[PATCH v14 0/9] MIPS: JZ4780 and CI20 HDMI

[PATCH v14 0/9] MIPS: JZ4780 and CI20 HDMI

[H. Nikolaus Schaller]

PATCH V14 2022-02-12 15:19:25:
* make compatible to c03d0b52ff71d5 ("drm/connector: Fix typo in output format")
* move "dw-hdmi/ingenic-dw-hdmi: repair interworking with hdmi-connector" before
  drm/ingenic: Add dw-hdmi driver specialization for jz4780 (by paul@crapouillou.net)
* split introduction of dw_hdmi_enable_poll() into separate patch
* explicitly mark plane f0 as not working in jz4780 (suggested by paul@crapouillou.net)
* drop 1/9 since it is now in drm-misc/drm-misc-next

PATCH V13 2022-02-02 17:31:22:
* 7/9: remove call to gpiod_set_value() because of GPIOD_OUT_HIGH (by paul@crapouillou.net)
* 4/9: replace ".." by "." (by paul@crapouillou.net)
* 3/9: remove old hdmi-5v-power in the example (by paul@crapouillou.net)
* 2/9: disable handling of plane f0 only for jz4780 (by paul@crapouillou.net)

PATCH V12 2022-01-31 13:26:54:
This version reworks how hdmi ddc power is controlled by connector and not
by ddc/hdmi bridge driver.

Also some patches of the previous version of this series have been removed
since they are already applied to mips-next/linux/next/v5.17-rc1.

Fixes and changes:

- repair interworking of dw-hdmi with connector-hdmi (by hns@goldelico.com)
- fix JZ_REG_LCD_OSDC setup for jz4780 (by hns@goldelico.com and paul@crapouillou.net)
- adjustments for ci20.dts to use connector gpio for +5v (suggested by several)
- to add control of "ddc-en-gpios" to hdmi-connector driver (by hns@goldelico.com)
- regulator code removed because we now use the "ddc-en-gpios" of the connector
  driver (suggested by paul@crapouillou.net)
- bindings: addition of "ddc-i2c-bus" and "hdmi-5v-supply" removed (suggested by robh+dt@kernel.org)
- rebase on v5.17-rc2

PATCH V11 2021-12-02 19:39:52:
- patch 4/8: change devm_regulator_get_optional to devm_regulator_get and
             remove NULL check (requested by broonie@kernel.org)
- patch 3/8: make hdmi-5v-supply required (requested by broonie@kernel.org)

PATCH V10 2021-11-30 22:26:41:
- patch 3/8: fix $id and $ref paths (found by robh@kernel.org)

PATCH V9 2021-11-24 22:29:14:
- patch 6/8: remove optional <0> for assigned-clocks and unintentionally included "unwedge" setup (found by paul@crapouillou.net)
- patch 4/8: some cosmetics
             make regulator enable/disable only if not NULL (found by paul@crapouillou.net)
             simplify/fix error handling and driver cleanup on remove (proposed by paul@crapouillou.net)
- patch 3/8: fix #include path in example (found by paul@crapouillou.net)
             fix missing "i" in unevaluatedProperties (found by robh@kernel.org)
             fix 4 spaces indentation for required: property (found by robh@kernel.org)

PATCH V8 2021-11-23 19:14:00:
- fix a bad editing result from patch 2/8 (found by paul@crapouillou.net)

PATCH V7 2021-11-23 18:46:23:
- changed gpio polarity of hdmi_power to 0 (suggested by paul@crapouillou.net)
- fixed LCD1 irq number (bug found by paul@crapouillou.net)
- removed "- 4" for calculating max_register (suggested by paul@crapouillou.net)
- use unevaluatedPropertes instead of additionalProperties (suggested by robh@kernel.org)
- moved and renamed ingenic,jz4780-hdmi.yaml (suggested by robh@kernel.org)
- adjusted assigned-clocks changes to upstream which added some for SSI (by hns@goldelico.com)
- rebased and tested with v5.16-rc2 + patch set drm/ingenic by paul@crapouillou.net (by hns@goldelico.com)

PATCH V6 2021-11-10 20:43:33:
- changed CONFIG_DRM_INGENIC_DW_HDMI to "m" (by hns@goldelico.com)
- made ingenic-dw-hdmi an independent platform driver which can be compiled as module
  and removed error patch fixes for IPU (suggested by paul@crapouillou.net)
- moved assigned-clocks from jz4780.dtsi to ci20.dts (suggested by paul@crapouillou.net)
- fixed reg property in jz4780.dtsi to cover all registers incl. gamma and vee (by hns@goldelico.com)
- added a base patch to calculate regmap size from DTS reg property (requested by paul@crapouillou.net)
- restored resetting all bits except one in LCDOSDC (requested by paul@crapouillou.net)
- clarified setting of cpos (suggested by paul@crapouillou.net)
- moved bindings definition for ddc-i2c-bus (suggested by paul@crapouillou.net)
- simplified mask definitions for JZ_LCD_DESSIZE (requested by paul@crapouillou.net)
- removed setting alpha premultiplication (suggested by paul@crapouillou.net)
- removed some comments (suggested by paul@crapouillou.net)

PATCH V5 2021-10-05 14:28:44:
- dropped mode_fixup and timings support in dw-hdmi as it is no longer needed in this V5 (by hns@goldelico.com)
- dropped "drm/ingenic: add some jz4780 specific features" (stimulated by paul@crapouillou.net)
- fixed typo in commit subject: "synopsis" -> "synopsys" (by hns@goldelico.com)
- swapped clocks in jz4780.dtsi to match synopsys,dw-hdmi.yaml (by hns@goldelico.com)
- improved, simplified, fixed, dtbschecked ingenic-jz4780-hdmi.yaml and made dependent of bridge/synopsys,dw-hdmi.yaml (based on suggestions by maxime@cerno.tech)
- fixed binding vs. driver&DTS use of hdmi-5v regulator (suggested by maxime@cerno.tech)
- dropped "drm/bridge: synopsis: Fix to properly handle HPD" - was a no longer needed workaround for a previous version
  (suggested by maxime@cerno.tech)

PATCH V4 2021-09-27 18:44:38:
- fix setting output_port = 1 (issue found by paul@crapouillou.net)
- ci20.dts: convert to use hdmi-connector (by hns@goldelico.com)
- add a hdmi-regulator to control +5V power (by hns@goldelico.com)
- added a fix to dw-hdmi to call drm_kms_helper_hotplug_event on plugin event detection (by hns@goldelico.com)
- always allocate extended descriptor but initialize only for jz4780 (by hns@goldelico.com)
- updated to work on top of "[PATCH v3 0/6] drm/ingenic: Various improvements v3" (by paul@crapouillou.net)
- rebased to v5.13-rc3

PATCH V3 2021-08-08 07:10:50:
This series adds HDMI support for JZ4780 and CI20 board (and fixes one IPU related issue in registration error path)
- [patch 1/8] switched from mode_fixup to atomic_check (suggested by robert.foss@linaro.org)
  - the call to the dw-hdmi specialization is still called mode_fixup
- [patch 3/8] diverse fixes for ingenic-drm-drv (suggested by paul@crapouillou.net)
  - factor out some non-HDMI features of the jz4780 into a separate patch
  - multiple fixes around max height
  - do not change regmap config but a copy on stack
  - define some constants
  - factor out fixing of drm_init error path for IPU into separate patch
  - use FIELD_PREP()
- [patch 8/8] conversion to component framework dropped (suggested by Laurent.pinchart@ideasonboard.com and paul@crapouillou.net)

PATCH V2 2021-08-05 16:08:05:
- code and commit messages revisited for checkpatch warnings
- rebased on v5.14-rc4
- include (failed, hence RFC 8/8) attempt to convert to component framework
  (was suggested by Paul Cercueil <paul@crapouillou.net> a while ago)

This series adds HDMI support for JZ4780 and CI20 board



H. Nikolaus Schaller (5):
  drm/bridge: display-connector: add ddc-en gpio support
  drm/bridge: dw-hdmi: repair interworking with hdmi-connector for
    jz4780
  drm/bridge: dw-hdmi: introduce dw_hdmi_enable_poll()
  drm/ingenic: dw-hdmi: make hot plug detection work for CI20
  [already applied to mips-fixes] MIPS: DTS: CI20: fix how ddc power is
    enabled

Paul Boddie (3):
  drm/ingenic: Add support for JZ4780 and HDMI output
  drm/ingenic: Add dw-hdmi driver specialization for jz4780
  [RFC] drm/ingenic: add some more features specific to jz4780

Sam Ravnborg (1):
  dt-bindings: display: Add ingenic,jz4780-dw-hdmi DT Schema

 .../display/bridge/ingenic,jz4780-hdmi.yaml   |  82 ++++++++++++++
 arch/mips/boot/dts/ingenic/ci20.dts           |  15 +--
 drivers/gpu/drm/bridge/display-connector.c    |  15 +++
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c     |  13 ++-
 drivers/gpu/drm/ingenic/Kconfig               |   9 ++
 drivers/gpu/drm/ingenic/Makefile              |   1 +
 drivers/gpu/drm/ingenic/ingenic-drm-drv.c     |  46 +++++++-
 drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c     | 106 ++++++++++++++++++
 include/drm/bridge/dw_hdmi.h                  |   1 +
 9 files changed, 271 insertions(+), 17 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
 create mode 100644 drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c

-- 
2.33.0

[PATCH v14 1/9] drm/ingenic: Add support for JZ4780 and HDMI output

[H. Nikolaus Schaller]

From: Paul Boddie <paul@boddie.org.uk>

Add support for the LCD controller present on JZ4780 SoCs.
This SoC uses 8-byte descriptors which extend the current
4-byte descriptors used for other Ingenic SoCs.

Note that plane f0 is not working and disabled to be
seen from user-space.

Tested on MIPS Creator CI20 board.

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
index 7f10d6eed549d..dcf44cb00821f 100644
--- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
+++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
@@ -65,8 +65,10 @@ struct ingenic_dma_hwdescs {
 struct jz_soc_info {
 	bool needs_dev_clk;
 	bool has_osd;
+	bool has_alpha;
 	bool map_noncoherent;
 	bool use_extended_hwdesc;
+	bool plane_f0_not_working;
 	unsigned int max_width, max_height;
 	const u32 *formats_f0, *formats_f1;
 	unsigned int num_formats_f0, num_formats_f1;
@@ -453,7 +455,7 @@ static int ingenic_drm_plane_atomic_check(struct drm_plane *plane,
 	if (!crtc)
 		return 0;
 
-	if (plane == &priv->f0)
+	if (priv->soc_info->plane_f0_not_working && plane == &priv->f0)
 		return -EINVAL;
 
 	crtc_state = drm_atomic_get_existing_crtc_state(state,
@@ -1055,6 +1057,7 @@ static int ingenic_drm_bind(struct device *dev, bool has_components)
 	long parent_rate;
 	unsigned int i, clone_mask = 0;
 	int ret, irq;
+	u32 osdc = 0;
 
 	soc_info = of_device_get_match_data(dev);
 	if (!soc_info) {
@@ -1312,7 +1315,10 @@ static int ingenic_drm_bind(struct device *dev, bool has_components)
 
 	/* Enable OSD if available */
 	if (soc_info->has_osd)
-		regmap_write(priv->map, JZ_REG_LCD_OSDC, JZ_LCD_OSDC_OSDEN);
+		osdc |= JZ_LCD_OSDC_OSDEN;
+	if (soc_info->has_alpha)
+		osdc |= JZ_LCD_OSDC_ALPHAEN;
+	regmap_write(priv->map, JZ_REG_LCD_OSDC, osdc);
 
 	mutex_init(&priv->clk_mutex);
 	priv->clock_nb.notifier_call = ingenic_drm_update_pixclk;
@@ -1511,7 +1517,9 @@ static const struct jz_soc_info jz4770_soc_info = {
 static const struct jz_soc_info jz4780_soc_info = {
 	.needs_dev_clk = true,
 	.has_osd = true,
+	.has_alpha = true,
 	.use_extended_hwdesc = true,
+	.plane_f0_not_working = true,	/* REVISIT */
 	.max_width = 4096,
 	.max_height = 2048,
 	.formats_f1 = jz4770_formats_f1,
-- 
2.33.0

[PATCH v14 2/9] dt-bindings: display: Add ingenic,jz4780-dw-hdmi DT Schema

[H. Nikolaus Schaller]

From: Sam Ravnborg <sam@ravnborg.org>

Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC.
Based on .txt binding from Zubair Lutfullah Kakakhel

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../display/bridge/ingenic,jz4780-hdmi.yaml   | 82 +++++++++++++++++++
 1 file changed, 82 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml

diff --git a/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml b/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
new file mode 100644
index 0000000000000..b8219eab4475a
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
@@ -0,0 +1,82 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ingenic,jz4780-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for Ingenic JZ4780 HDMI Transmitter
+
+maintainers:
+  - H. Nikolaus Schaller <hns@goldelico.com>
+
+description: |
+  The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys DesignWare HDMI 1.4
+  TX controller IP with accompanying PHY IP.
+
+allOf:
+  - $ref: synopsys,dw-hdmi.yaml#
+
+properties:
+  compatible:
+    const: ingenic,jz4780-dw-hdmi
+
+  reg-io-width:
+    const: 4
+
+  clocks:
+    maxItems: 2
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input from LCD controller output.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Link to the HDMI connector.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - ports
+  - reg-io-width
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/ingenic,jz4780-cgu.h>
+
+    hdmi: hdmi@10180000 {
+        compatible = "ingenic,jz4780-dw-hdmi";
+        reg = <0x10180000 0x8000>;
+        reg-io-width = <4>;
+        ddc-i2c-bus = <&i2c4>;
+        interrupt-parent = <&intc>;
+        interrupts = <3>;
+        clocks = <&cgu JZ4780_CLK_AHB0>, <&cgu JZ4780_CLK_HDMI>;
+        clock-names = "iahb", "isfr";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            hdmi_in: port@0 {
+                reg = <0>;
+                dw_hdmi_in: endpoint {
+                    remote-endpoint = <&jz4780_lcd_out>;
+                };
+            };
+            hdmi_out: port@1 {
+                reg = <1>;
+                dw_hdmi_out: endpoint {
+                    remote-endpoint = <&hdmi_con>;
+                };
+            };
+        };
+    };
+
+...
-- 
2.33.0

[PATCH v14 3/9] drm/ingenic: Add dw-hdmi driver specialization for jz4780

[H. Nikolaus Schaller]

From: Paul Boddie <paul@boddie.org.uk>

A specialisation of the generic Synopsys HDMI driver is employed for
JZ4780 HDMI support. This requires a new driver, plus device tree and
configuration modifications.

Here we add Kconfig DRM_INGENIC_DW_HDMI, Makefile and driver code.

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/ingenic/Kconfig           |   9 ++
 drivers/gpu/drm/ingenic/Makefile          |   1 +
 drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c | 104 ++++++++++++++++++++++
 3 files changed, 114 insertions(+)
 create mode 100644 drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c

diff --git a/drivers/gpu/drm/ingenic/Kconfig b/drivers/gpu/drm/ingenic/Kconfig
index 001f59fb06d56..090830bcbde7f 100644
--- a/drivers/gpu/drm/ingenic/Kconfig
+++ b/drivers/gpu/drm/ingenic/Kconfig
@@ -24,4 +24,13 @@ config DRM_INGENIC_IPU
 
 	  The Image Processing Unit (IPU) will appear as a second primary plane.
 
+config DRM_INGENIC_DW_HDMI
+	tristate "Ingenic specific support for Synopsys DW HDMI"
+	depends on MACH_JZ4780
+	select DRM_DW_HDMI
+	help
+	  Choose this option to enable Synopsys DesignWare HDMI based driver.
+	  If you want to enable HDMI on Ingenic JZ4780 based SoC, you should
+	  select this option.
+
 endif
diff --git a/drivers/gpu/drm/ingenic/Makefile b/drivers/gpu/drm/ingenic/Makefile
index d313326bdddbb..f10cc1c5a5f22 100644
--- a/drivers/gpu/drm/ingenic/Makefile
+++ b/drivers/gpu/drm/ingenic/Makefile
@@ -1,3 +1,4 @@
 obj-$(CONFIG_DRM_INGENIC) += ingenic-drm.o
 ingenic-drm-y = ingenic-drm-drv.o
 ingenic-drm-$(CONFIG_DRM_INGENIC_IPU) += ingenic-ipu.o
+obj-$(CONFIG_DRM_INGENIC_DW_HDMI) += ingenic-dw-hdmi.o
diff --git a/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c b/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c
new file mode 100644
index 0000000000000..34e986dd606cf
--- /dev/null
+++ b/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2011-2013 Freescale Semiconductor, Inc.
+ * Copyright (C) 2019, 2020 Paul Boddie <paul@boddie.org.uk>
+ *
+ * Derived from dw_hdmi-imx.c with i.MX portions removed.
+ * Probe and remove operations derived from rcar_dw_hdmi.c.
+ */
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include <drm/bridge/dw_hdmi.h>
+#include <drm/drm_of.h>
+#include <drm/drm_print.h>
+
+static const struct dw_hdmi_mpll_config ingenic_mpll_cfg[] = {
+	{ 45250000,  { { 0x01e0, 0x0000 }, { 0x21e1, 0x0000 }, { 0x41e2, 0x0000 } } },
+	{ 92500000,  { { 0x0140, 0x0005 }, { 0x2141, 0x0005 }, { 0x4142, 0x0005 } } },
+	{ 148500000, { { 0x00a0, 0x000a }, { 0x20a1, 0x000a }, { 0x40a2, 0x000a } } },
+	{ 216000000, { { 0x00a0, 0x000a }, { 0x2001, 0x000f }, { 0x4002, 0x000f } } },
+	{ ~0UL,      { { 0x0000, 0x0000 }, { 0x0000, 0x0000 }, { 0x0000, 0x0000 } } }
+};
+
+static const struct dw_hdmi_curr_ctrl ingenic_cur_ctr[] = {
+	/*pixelclk     bpp8    bpp10   bpp12 */
+	{ 54000000,  { 0x091c, 0x091c, 0x06dc } },
+	{ 58400000,  { 0x091c, 0x06dc, 0x06dc } },
+	{ 72000000,  { 0x06dc, 0x06dc, 0x091c } },
+	{ 74250000,  { 0x06dc, 0x0b5c, 0x091c } },
+	{ 118800000, { 0x091c, 0x091c, 0x06dc } },
+	{ 216000000, { 0x06dc, 0x0b5c, 0x091c } },
+	{ ~0UL,      { 0x0000, 0x0000, 0x0000 } },
+};
+
+/*
+ * Resistance term 133Ohm Cfg
+ * PREEMP config 0.00
+ * TX/CK level 10
+ */
+static const struct dw_hdmi_phy_config ingenic_phy_config[] = {
+	/*pixelclk   symbol   term   vlev */
+	{ 216000000, 0x800d, 0x0005, 0x01ad},
+	{ ~0UL,      0x0000, 0x0000, 0x0000}
+};
+
+static enum drm_mode_status
+ingenic_dw_hdmi_mode_valid(struct dw_hdmi *hdmi, void *data,
+			   const struct drm_display_info *info,
+			   const struct drm_display_mode *mode)
+{
+	if (mode->clock < 13500)
+		return MODE_CLOCK_LOW;
+	/* FIXME: Hardware is capable of 270MHz, but setup data is missing. */
+	if (mode->clock > 216000)
+		return MODE_CLOCK_HIGH;
+
+	return MODE_OK;
+}
+
+static struct dw_hdmi_plat_data ingenic_dw_hdmi_plat_data = {
+	.mpll_cfg   = ingenic_mpll_cfg,
+	.cur_ctr    = ingenic_cur_ctr,
+	.phy_config = ingenic_phy_config,
+	.mode_valid = ingenic_dw_hdmi_mode_valid,
+	.output_port	= 1,
+};
+
+static const struct of_device_id ingenic_dw_hdmi_dt_ids[] = {
+	{ .compatible = "ingenic,jz4780-dw-hdmi" },
+	{ /* Sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, ingenic_dw_hdmi_dt_ids);
+
+static void ingenic_dw_hdmi_cleanup(void *data)
+{
+	struct dw_hdmi *hdmi = (struct dw_hdmi *)data;
+
+	dw_hdmi_remove(hdmi);
+}
+
+static int ingenic_dw_hdmi_probe(struct platform_device *pdev)
+{
+	struct dw_hdmi *hdmi;
+
+	hdmi = dw_hdmi_probe(pdev, &ingenic_dw_hdmi_plat_data);
+	if (IS_ERR(hdmi))
+		return PTR_ERR(hdmi);
+
+	return devm_add_action_or_reset(&pdev->dev, ingenic_dw_hdmi_cleanup, hdmi);
+}
+
+static struct platform_driver ingenic_dw_hdmi_driver = {
+	.probe  = ingenic_dw_hdmi_probe,
+	.driver = {
+		.name = "dw-hdmi-ingenic",
+		.of_match_table = ingenic_dw_hdmi_dt_ids,
+	},
+};
+module_platform_driver(ingenic_dw_hdmi_driver);
+
+MODULE_DESCRIPTION("JZ4780 Specific DW-HDMI Driver Extension");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dwhdmi-ingenic");
-- 
2.33.0

[PATCH v14 4/9] drm/bridge: display-connector: add ddc-en gpio support

[H. Nikolaus Schaller]

"hdmi-connector.yaml" bindings defines an optional property
"ddc-en-gpios" for a single gpio to enable DDC operation.

Usually this controls +5V power on the HDMI connector.
This +5V may also be needed for HPD.

This was not reflected in code.

Now, the driver activates the ddc gpio after probe and
deactivates after remove so it is "almost on".

But only if this driver is loaded (and not e.g. blacklisted
as module).

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/bridge/display-connector.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/gpu/drm/bridge/display-connector.c b/drivers/gpu/drm/bridge/display-connector.c
index d24f5b90feabf..e4d52a7e31b71 100644
--- a/drivers/gpu/drm/bridge/display-connector.c
+++ b/drivers/gpu/drm/bridge/display-connector.c
@@ -24,6 +24,7 @@ struct display_connector {
 	int			hpd_irq;
 
 	struct regulator	*dp_pwr;
+	struct gpio_desc	*ddc_en;
 };
 
 static inline struct display_connector *
@@ -345,6 +346,17 @@ static int display_connector_probe(struct platform_device *pdev)
 		}
 	}
 
+	/* enable DDC */
+	if (type == DRM_MODE_CONNECTOR_HDMIA) {
+		conn->ddc_en = devm_gpiod_get_optional(&pdev->dev, "ddc-en",
+						       GPIOD_OUT_HIGH);
+
+		if (IS_ERR(conn->ddc_en)) {
+			dev_err(&pdev->dev, "Couldn't get ddc-en gpio\n");
+			return PTR_ERR(conn->ddc_en);
+		}
+	}
+
 	conn->bridge.funcs = &display_connector_bridge_funcs;
 	conn->bridge.of_node = pdev->dev.of_node;
 
@@ -373,6 +385,9 @@ static int display_connector_remove(struct platform_device *pdev)
 {
 	struct display_connector *conn = platform_get_drvdata(pdev);
 
+	if (conn->ddc_en)
+		gpiod_set_value(conn->ddc_en, 0);
+
 	if (conn->dp_pwr)
 		regulator_disable(conn->dp_pwr);
 
-- 
2.33.0

[PATCH v14 5/9] drm/bridge: dw-hdmi: repair interworking with hdmi-connector for jz4780

[H. Nikolaus Schaller]

Commit 7cd70656d1285b ("drm/bridge: display-connector: implement bus fmts callbacks")

introduced a new mechanism to negotiate bus formats between hdmi connector
and the synopsys hdmi driver inside the jz4780.

By this, the dw-hdmi is no longer the only bridge and sets up a list
of formats in dw_hdmi_bridge_atomic_get_output_bus_fmts().

This includes MEDIA_BUS_FMT_UYVY8_1X16 which is chosen for the jz4780 but only
produces a black screen.

This fix is based on the observation that max_bpc = 0 when running this
function while info->bpc = 8. Since the formats checks before this always test
for max_bpc >= info->pbc indirectly my assumption is that we must check it
here as well.

Adding the proposed patch makes the CI20/jz4780 panel work again in
MEDIA_BUS_FMT_RGB888_1X24 mode.

Fixes: 7cd70656d1285b ("drm/bridge: display-connector: implement bus fmts callbacks")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
index b0d8110dd412c..826a055a7a273 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -2620,10 +2620,10 @@ static u32 *dw_hdmi_bridge_atomic_get_output_bus_fmts(struct drm_bridge *bridge,
 		output_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
 	}
 
-	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR422)
+	if (max_bpc >= info->bpc && info->color_formats & DRM_COLOR_FORMAT_YCBCR422)
 		output_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
 
-	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR444)
+	if (max_bpc >= info->bpc && info->color_formats & DRM_COLOR_FORMAT_YCBCR444)
 		output_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
 
 	/* Default 8bit RGB fallback */
-- 
2.33.0

[PATCH v14 6/9] drm/bridge: dw-hdmi: introduce dw_hdmi_enable_poll()

[H. Nikolaus Schaller]

so that specialization drivers like ingenic-dw-hdmi can enable polling.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 9 +++++++++
 include/drm/bridge/dw_hdmi.h              | 1 +
 2 files changed, 10 insertions(+)

diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
index 826a055a7a273..fc2d5422c8a19 100644
--- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
+++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
@@ -3216,6 +3216,15 @@ static int dw_hdmi_parse_dt(struct dw_hdmi *hdmi)
 	return 0;
 }
 
+void dw_hdmi_enable_poll(struct dw_hdmi *hdmi, bool enable)
+{
+	if (hdmi->bridge.dev)
+		hdmi->bridge.dev->mode_config.poll_enabled = enable;
+	else
+		dev_warn(hdmi->dev, "no hdmi->bridge.dev");
+}
+EXPORT_SYMBOL_GPL(dw_hdmi_enable_poll);
+
 struct dw_hdmi *dw_hdmi_probe(struct platform_device *pdev,
 			      const struct dw_hdmi_plat_data *plat_data)
 {
diff --git a/include/drm/bridge/dw_hdmi.h b/include/drm/bridge/dw_hdmi.h
index 2a1f85f9a8a3f..963960794b40e 100644
--- a/include/drm/bridge/dw_hdmi.h
+++ b/include/drm/bridge/dw_hdmi.h
@@ -196,5 +196,6 @@ enum drm_connector_status dw_hdmi_phy_read_hpd(struct dw_hdmi *hdmi,
 void dw_hdmi_phy_update_hpd(struct dw_hdmi *hdmi, void *data,
 			    bool force, bool disabled, bool rxsense);
 void dw_hdmi_phy_setup_hpd(struct dw_hdmi *hdmi, void *data);
+void dw_hdmi_enable_poll(struct dw_hdmi *hdmi, bool enable);
 
 #endif /* __IMX_HDMI_H__ */
-- 
2.33.0

[PATCH v14 7/9] drm/ingenic: dw-hdmi: make hot plug detection work for CI20

[H. Nikolaus Schaller]

There is no hpd-gpio installed on the CI20 board HDMI connector.
Hence there is no hpd detection by the connector driver and we
have to enable polling by the dw-hdmi driver.

We need to set .poll_enabled but that struct component
can only be accessed in the core code. Hence we use the public
setter function drm_kms_helper_hotplug_event().

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c b/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c
index 34e986dd606cf..90547a28dc5c7 100644
--- a/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c
+++ b/drivers/gpu/drm/ingenic/ingenic-dw-hdmi.c
@@ -55,6 +55,8 @@ ingenic_dw_hdmi_mode_valid(struct dw_hdmi *hdmi, void *data,
 	if (mode->clock > 216000)
 		return MODE_CLOCK_HIGH;
 
+	dw_hdmi_enable_poll(hdmi, true);
+
 	return MODE_OK;
 }
 
-- 
2.33.0

[PATCH v14 8/9] [already applied to mips-fixes] MIPS: DTS: CI20: fix how ddc power is enabled

[H. Nikolaus Schaller]

Originally we proposed a new hdmi-5v-supply regulator reference
for CI20 device tree but that was superseded by a better idea to use
the already defined "ddc-en-gpios" property of the "hdmi-connector".

Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already
been applied to v5.17-rc1, we add this on top.

Fixes: ae1b8d2c2de9 ("MIPS: DTS: CI20: Add DT nodes for HDMI setup")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
---
 arch/mips/boot/dts/ingenic/ci20.dts | 15 ++-------------
 1 file changed, 2 insertions(+), 13 deletions(-)

diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 3e336b3dbb109..ab6e3dc0bc1d0 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -83,6 +83,8 @@ hdmi_out: connector {
 		label = "HDMI OUT";
 		type = "a";
 
+		ddc-en-gpios = <&gpa 25 GPIO_ACTIVE_HIGH>;
+
 		port {
 			hdmi_con: endpoint {
 				remote-endpoint = <&dw_hdmi_out>;
@@ -114,17 +116,6 @@ otg_power: fixedregulator@2 {
 		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
 		enable-active-high;
 	};
-
-	hdmi_power: fixedregulator@3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "hdmi_power";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpa 25 0>;
-		enable-active-high;
-	};
 };
 
 &ext {
@@ -576,8 +567,6 @@ &hdmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pins_hdmi_ddc>;
 
-	hdmi-5v-supply = <&hdmi_power>;
-
 	ports {
 		#address-cells = <1>;
 		#size-cells = <0>;
-- 
2.33.0

[PATCH v14 9/9] [RFC] drm/ingenic: add some more features specific to jz4780

[H. Nikolaus Schaller]

From: Paul Boddie <paul@boddie.org.uk>

The jz4780 has some more features which should be initialized
according to the vendor kernel.

Signed-off-by: Paul Boddie <paul@boddie.org.uk>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
---
 drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 34 +++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
index dcf44cb00821f..fb2cdb188b993 100644
--- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
+++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
@@ -66,6 +66,9 @@ struct jz_soc_info {
 	bool needs_dev_clk;
 	bool has_osd;
 	bool has_alpha;
+	bool has_pcfg;
+	bool has_recover;
+	bool has_rgbc;
 	bool map_noncoherent;
 	bool use_extended_hwdesc;
 	bool plane_f0_not_working;
@@ -732,6 +735,9 @@ static void ingenic_drm_encoder_atomic_mode_set(struct drm_encoder *encoder,
 		    | JZ_LCD_CFG_SPL_DISABLE | JZ_LCD_CFG_REV_DISABLE;
 	}
 
+	if (priv->soc_info->has_recover)
+		cfg |= JZ_LCD_CFG_RECOVER_FIFO_UNDERRUN;
+
 	if (priv->soc_info->use_extended_hwdesc)
 		cfg |= JZ_LCD_CFG_DESCRIPTOR_8;
 
@@ -1320,6 +1326,22 @@ static int ingenic_drm_bind(struct device *dev, bool has_components)
 		osdc |= JZ_LCD_OSDC_ALPHAEN;
 	regmap_write(priv->map, JZ_REG_LCD_OSDC, osdc);
 
+	/* Magic values from the vendor kernel for the priority thresholds. */
+	if (soc_info->has_pcfg)
+		regmap_write(priv->map, JZ_REG_LCD_PCFG,
+			     JZ_LCD_PCFG_PRI_MODE |
+			     JZ_LCD_PCFG_HP_BST_16 |
+			     (511 << JZ_LCD_PCFG_THRESHOLD2_OFFSET) |
+			     (400 << JZ_LCD_PCFG_THRESHOLD1_OFFSET) |
+			     (256 << JZ_LCD_PCFG_THRESHOLD0_OFFSET));
+
+	/* RGB output control may be superfluous. */
+	if (soc_info->has_rgbc)
+		regmap_write(priv->map, JZ_REG_LCD_RGBC,
+			     JZ_LCD_RGBC_RGB_FORMAT_ENABLE |
+			     JZ_LCD_RGBC_ODD_RGB |
+			     JZ_LCD_RGBC_EVEN_RGB);
+
 	mutex_init(&priv->clk_mutex);
 	priv->clock_nb.notifier_call = ingenic_drm_update_pixclk;
 
@@ -1483,6 +1505,9 @@ static const struct jz_soc_info jz4740_soc_info = {
 	.needs_dev_clk = true,
 	.has_osd = false,
 	.map_noncoherent = false,
+	.has_pcfg = false,
+	.has_recover = false,
+	.has_rgbc = false,
 	.max_width = 800,
 	.max_height = 600,
 	.formats_f1 = jz4740_formats,
@@ -1494,6 +1519,9 @@ static const struct jz_soc_info jz4725b_soc_info = {
 	.needs_dev_clk = false,
 	.has_osd = true,
 	.map_noncoherent = false,
+	.has_pcfg = false,
+	.has_recover = true,
+	.has_rgbc = true,
 	.max_width = 800,
 	.max_height = 600,
 	.formats_f1 = jz4725b_formats_f1,
@@ -1506,6 +1534,9 @@ static const struct jz_soc_info jz4770_soc_info = {
 	.needs_dev_clk = false,
 	.has_osd = true,
 	.map_noncoherent = true,
+	.has_pcfg = false,
+	.has_recover = true,
+	.has_rgbc = true,
 	.max_width = 1280,
 	.max_height = 720,
 	.formats_f1 = jz4770_formats_f1,
@@ -1518,6 +1549,9 @@ static const struct jz_soc_info jz4780_soc_info = {
 	.needs_dev_clk = true,
 	.has_osd = true,
 	.has_alpha = true,
+	.has_pcfg = true,
+	.has_recover = true,
+	.has_rgbc = true,
 	.use_extended_hwdesc = true,
 	.plane_f0_not_working = true,	/* REVISIT */
 	.max_width = 4096,
-- 
2.33.0

Re: [PATCH v14 1/9] drm/ingenic: Add support for JZ4780 and HDMI output

[Paul Cercueil]

Hi Nikolaus,

Le sam., févr. 12 2022 at 15:19:19 +0100, H. Nikolaus Schaller 
<hns@goldelico.com> a écrit :
> From: Paul Boddie <paul@boddie.org.uk>
> 
> Add support for the LCD controller present on JZ4780 SoCs.
> This SoC uses 8-byte descriptors which extend the current
> 4-byte descriptors used for other Ingenic SoCs.
> 
> Note that plane f0 is not working and disabled to be
> seen from user-space.
> 
> Tested on MIPS Creator CI20 board.

That's not really what the patch does though. It's a fix for a commit 
that has the exact same title and description, and is already merged: 
b807fd2c43fe ("drm/ingenic: Add support for JZ4780 and HDMI output").

Please rewrite the patch's title and description to actually describe 
its purpose.

Cheers,
-Paul

> 
> Signed-off-by: Paul Boddie <paul@boddie.org.uk>
> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> ---
>  drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 12 ++++++++++--
>  1 file changed, 10 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c 
> b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
> index 7f10d6eed549d..dcf44cb00821f 100644
> --- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
> +++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
> @@ -65,8 +65,10 @@ struct ingenic_dma_hwdescs {
>  struct jz_soc_info {
>  	bool needs_dev_clk;
>  	bool has_osd;
> +	bool has_alpha;
>  	bool map_noncoherent;
>  	bool use_extended_hwdesc;
> +	bool plane_f0_not_working;
>  	unsigned int max_width, max_height;
>  	const u32 *formats_f0, *formats_f1;
>  	unsigned int num_formats_f0, num_formats_f1;
> @@ -453,7 +455,7 @@ static int ingenic_drm_plane_atomic_check(struct 
> drm_plane *plane,
>  	if (!crtc)
>  		return 0;
> 
> -	if (plane == &priv->f0)
> +	if (priv->soc_info->plane_f0_not_working && plane == &priv->f0)
>  		return -EINVAL;
> 
>  	crtc_state = drm_atomic_get_existing_crtc_state(state,
> @@ -1055,6 +1057,7 @@ static int ingenic_drm_bind(struct device *dev, 
> bool has_components)
>  	long parent_rate;
>  	unsigned int i, clone_mask = 0;
>  	int ret, irq;
> +	u32 osdc = 0;
> 
>  	soc_info = of_device_get_match_data(dev);
>  	if (!soc_info) {
> @@ -1312,7 +1315,10 @@ static int ingenic_drm_bind(struct device 
> *dev, bool has_components)
> 
>  	/* Enable OSD if available */
>  	if (soc_info->has_osd)
> -		regmap_write(priv->map, JZ_REG_LCD_OSDC, JZ_LCD_OSDC_OSDEN);
> +		osdc |= JZ_LCD_OSDC_OSDEN;
> +	if (soc_info->has_alpha)
> +		osdc |= JZ_LCD_OSDC_ALPHAEN;
> +	regmap_write(priv->map, JZ_REG_LCD_OSDC, osdc);
> 
>  	mutex_init(&priv->clk_mutex);
>  	priv->clock_nb.notifier_call = ingenic_drm_update_pixclk;
> @@ -1511,7 +1517,9 @@ static const struct jz_soc_info jz4770_soc_info 
> = {
>  static const struct jz_soc_info jz4780_soc_info = {
>  	.needs_dev_clk = true,
>  	.has_osd = true,
> +	.has_alpha = true,
>  	.use_extended_hwdesc = true,
> +	.plane_f0_not_working = true,	/* REVISIT */
>  	.max_width = 4096,
>  	.max_height = 2048,
>  	.formats_f1 = jz4770_formats_f1,
> --
> 2.33.0
> 

Re: [PATCH v14 2/9] dt-bindings: display: Add ingenic,jz4780-dw-hdmi DT Schema

[Paul Cercueil]

Hi,

Le sam., févr. 12 2022 at 15:19:20 +0100, H. Nikolaus Schaller 
<hns@goldelico.com> a écrit :
> From: Sam Ravnborg <sam@ravnborg.org>
> 
> Add DT bindings for the hdmi driver for the Ingenic JZ4780 SoC.
> Based on .txt binding from Zubair Lutfullah Kakakhel
> 
> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> Cc: Rob Herring <robh@kernel.org>
> Cc: devicetree@vger.kernel.org
> Reviewed-by: Rob Herring <robh@kernel.org>

Patch pushed to drm-misc-next, thanks!

Cheers,
-Paul

> ---
>  .../display/bridge/ingenic,jz4780-hdmi.yaml   | 82 
> +++++++++++++++++++
>  1 file changed, 82 insertions(+)
>  create mode 100644 
> Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
> 
> diff --git 
> a/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml 
> b/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
> new file mode 100644
> index 0000000000000..b8219eab4475a
> --- /dev/null
> +++ 
> b/Documentation/devicetree/bindings/display/bridge/ingenic,jz4780-hdmi.yaml
> @@ -0,0 +1,82 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: 
> http://devicetree.org/schemas/display/bridge/ingenic,jz4780-hdmi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Bindings for Ingenic JZ4780 HDMI Transmitter
> +
> +maintainers:
> +  - H. Nikolaus Schaller <hns@goldelico.com>
> +
> +description: |
> +  The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys 
> DesignWare HDMI 1.4
> +  TX controller IP with accompanying PHY IP.
> +
> +allOf:
> +  - $ref: synopsys,dw-hdmi.yaml#
> +
> +properties:
> +  compatible:
> +    const: ingenic,jz4780-dw-hdmi
> +
> +  reg-io-width:
> +    const: 4
> +
> +  clocks:
> +    maxItems: 2
> +
> +  ports:
> +    $ref: /schemas/graph.yaml#/properties/ports
> +
> +    properties:
> +      port@0:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Input from LCD controller output.
> +
> +      port@1:
> +        $ref: /schemas/graph.yaml#/properties/port
> +        description: Link to the HDMI connector.
> +
> +required:
> +  - compatible
> +  - clocks
> +  - clock-names
> +  - ports
> +  - reg-io-width
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/ingenic,jz4780-cgu.h>
> +
> +    hdmi: hdmi@10180000 {
> +        compatible = "ingenic,jz4780-dw-hdmi";
> +        reg = <0x10180000 0x8000>;
> +        reg-io-width = <4>;
> +        ddc-i2c-bus = <&i2c4>;
> +        interrupt-parent = <&intc>;
> +        interrupts = <3>;
> +        clocks = <&cgu JZ4780_CLK_AHB0>, <&cgu JZ4780_CLK_HDMI>;
> +        clock-names = "iahb", "isfr";
> +
> +        ports {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +            hdmi_in: port@0 {
> +                reg = <0>;
> +                dw_hdmi_in: endpoint {
> +                    remote-endpoint = <&jz4780_lcd_out>;
> +                };
> +            };
> +            hdmi_out: port@1 {
> +                reg = <1>;
> +                dw_hdmi_out: endpoint {
> +                    remote-endpoint = <&hdmi_con>;
> +                };
> +            };
> +        };
> +    };
> +
> +...
> --
> 2.33.0
> 

Re: [PATCH v14 8/9] [already applied to mips-fixes] MIPS: DTS: CI20: fix how ddc power is enabled

[Paul Cercueil]

Hi,

Le sam., févr. 12 2022 at 15:19:26 +0100, H. Nikolaus Schaller 
<hns@goldelico.com> a écrit :
> Originally we proposed a new hdmi-5v-supply regulator reference
> for CI20 device tree but that was superseded by a better idea to use
> the already defined "ddc-en-gpios" property of the "hdmi-connector".
> 
> Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already
> been applied to v5.17-rc1, we add this on top.
> 
> Fixes: ae1b8d2c2de9 ("MIPS: DTS: CI20: Add DT nodes for HDMI setup")
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> Reviewed-by: Paul Cercueil <paul@crapouillou.net>

Since it's already applied you don't have to send this patch anymore.

Cheers,
-Paul

> ---
>  arch/mips/boot/dts/ingenic/ci20.dts | 15 ++-------------
>  1 file changed, 2 insertions(+), 13 deletions(-)
> 
> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts 
> b/arch/mips/boot/dts/ingenic/ci20.dts
> index 3e336b3dbb109..ab6e3dc0bc1d0 100644
> --- a/arch/mips/boot/dts/ingenic/ci20.dts
> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> @@ -83,6 +83,8 @@ hdmi_out: connector {
>  		label = "HDMI OUT";
>  		type = "a";
> 
> +		ddc-en-gpios = <&gpa 25 GPIO_ACTIVE_HIGH>;
> +
>  		port {
>  			hdmi_con: endpoint {
>  				remote-endpoint = <&dw_hdmi_out>;
> @@ -114,17 +116,6 @@ otg_power: fixedregulator@2 {
>  		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
>  		enable-active-high;
>  	};
> -
> -	hdmi_power: fixedregulator@3 {
> -		compatible = "regulator-fixed";
> -
> -		regulator-name = "hdmi_power";
> -		regulator-min-microvolt = <5000000>;
> -		regulator-max-microvolt = <5000000>;
> -
> -		gpio = <&gpa 25 0>;
> -		enable-active-high;
> -	};
>  };
> 
>  &ext {
> @@ -576,8 +567,6 @@ &hdmi {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pins_hdmi_ddc>;
> 
> -	hdmi-5v-supply = <&hdmi_power>;
> -
>  	ports {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> --
> 2.33.0
> 

Re: [PATCH v14 5/9] drm/bridge: dw-hdmi: repair interworking with hdmi-connector for jz4780

[Paul Cercueil]

Hi Nikolaus,


Le sam., févr. 12 2022 at 15:19:23 +0100, H. Nikolaus Schaller 
<hns@goldelico.com> a écrit :
> Commit 7cd70656d1285b ("drm/bridge: display-connector: implement bus 
> fmts callbacks")
> 
> introduced a new mechanism to negotiate bus formats between hdmi 
> connector
> and the synopsys hdmi driver inside the jz4780.
> 
> By this, the dw-hdmi is no longer the only bridge and sets up a list
> of formats in dw_hdmi_bridge_atomic_get_output_bus_fmts().
> 
> This includes MEDIA_BUS_FMT_UYVY8_1X16 which is chosen for the jz4780 
> but only
> produces a black screen.

Neil pushed a fix yesterday that looks like it could fix your issue.
The fix is: 1528038385c0 ("drm/bridge: dw-hdmi: use safe format when 
first in bridge chain")

Could you try if it does indeed fix your issue?

Cheers,
-Paul

> This fix is based on the observation that max_bpc = 0 when running 
> this
> function while info->bpc = 8. Since the formats checks before this 
> always test
> for max_bpc >= info->pbc indirectly my assumption is that we must 
> check it
> here as well.
> 
> Adding the proposed patch makes the CI20/jz4780 panel work again in
> MEDIA_BUS_FMT_RGB888_1X24 mode.
> 
> Fixes: 7cd70656d1285b ("drm/bridge: display-connector: implement bus 
> fmts callbacks")
> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
> ---
>  drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c 
> b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> index b0d8110dd412c..826a055a7a273 100644
> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
> @@ -2620,10 +2620,10 @@ static u32 
> *dw_hdmi_bridge_atomic_get_output_bus_fmts(struct drm_bridge *bridge,
>  		output_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
>  	}
> 
> -	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR422)
> +	if (max_bpc >= info->bpc && info->color_formats & 
> DRM_COLOR_FORMAT_YCBCR422)
>  		output_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
> 
> -	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR444)
> +	if (max_bpc >= info->bpc && info->color_formats & 
> DRM_COLOR_FORMAT_YCBCR444)
>  		output_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
> 
>  	/* Default 8bit RGB fallback */
> --
> 2.33.0
> 

Re: [PATCH v14 1/9] drm/ingenic: Add support for JZ4780 and HDMI output

[H. Nikolaus Schaller]

Hi Paul,

> Am 12.02.2022 um 15:44 schrieb Paul Cercueil <paul@crapouillou.net>:
> 
> Hi Nikolaus,
> 
> Le sam., févr. 12 2022 at 15:19:19 +0100, H. Nikolaus Schaller <hns@goldelico.com> a écrit :
>> From: Paul Boddie <paul@boddie.org.uk>
>> Add support for the LCD controller present on JZ4780 SoCs.
>> This SoC uses 8-byte descriptors which extend the current
>> 4-byte descriptors used for other Ingenic SoCs.
>> Note that plane f0 is not working and disabled to be
>> seen from user-space.
>> Tested on MIPS Creator CI20 board.
> 
> That's not really what the patch does though. It's a fix for a commit that has the exact same title and description, and is already merged: b807fd2c43fe ("drm/ingenic: Add support for JZ4780 and HDMI output").

Well, last version was not a fix...

I simply did not notice that parts of the commit contents were removed by rebase to drm-misc-next and the commit message diverged...

> Please rewrite the patch's title and description to actually describe its purpose.

Well, git rebase should do this for us if it removes the code described in the commit and makes a fix out of it. What do we have automation for :)

v15 will come now...

BR and thanks,
Nikolaus

> 
> Cheers,
> -Paul
> 
>> Signed-off-by: Paul Boddie <paul@boddie.org.uk>
>> Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> ---
>> drivers/gpu/drm/ingenic/ingenic-drm-drv.c | 12 ++++++++++--
>> 1 file changed, 10 insertions(+), 2 deletions(-)
>> diff --git a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> index 7f10d6eed549d..dcf44cb00821f 100644
>> --- a/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> +++ b/drivers/gpu/drm/ingenic/ingenic-drm-drv.c
>> @@ -65,8 +65,10 @@ struct ingenic_dma_hwdescs {
>> struct jz_soc_info {
>> 	bool needs_dev_clk;
>> 	bool has_osd;
>> +	bool has_alpha;
>> 	bool map_noncoherent;
>> 	bool use_extended_hwdesc;
>> +	bool plane_f0_not_working;
>> 	unsigned int max_width, max_height;
>> 	const u32 *formats_f0, *formats_f1;
>> 	unsigned int num_formats_f0, num_formats_f1;
>> @@ -453,7 +455,7 @@ static int ingenic_drm_plane_atomic_check(struct drm_plane *plane,
>> 	if (!crtc)
>> 		return 0;
>> -	if (plane == &priv->f0)
>> +	if (priv->soc_info->plane_f0_not_working && plane == &priv->f0)
>> 		return -EINVAL;
>> 	crtc_state = drm_atomic_get_existing_crtc_state(state,
>> @@ -1055,6 +1057,7 @@ static int ingenic_drm_bind(struct device *dev, bool has_components)
>> 	long parent_rate;
>> 	unsigned int i, clone_mask = 0;
>> 	int ret, irq;
>> +	u32 osdc = 0;
>> 	soc_info = of_device_get_match_data(dev);
>> 	if (!soc_info) {
>> @@ -1312,7 +1315,10 @@ static int ingenic_drm_bind(struct device *dev, bool has_components)
>> 	/* Enable OSD if available */
>> 	if (soc_info->has_osd)
>> -		regmap_write(priv->map, JZ_REG_LCD_OSDC, JZ_LCD_OSDC_OSDEN);
>> +		osdc |= JZ_LCD_OSDC_OSDEN;
>> +	if (soc_info->has_alpha)
>> +		osdc |= JZ_LCD_OSDC_ALPHAEN;
>> +	regmap_write(priv->map, JZ_REG_LCD_OSDC, osdc);
>> 	mutex_init(&priv->clk_mutex);
>> 	priv->clock_nb.notifier_call = ingenic_drm_update_pixclk;
>> @@ -1511,7 +1517,9 @@ static const struct jz_soc_info jz4770_soc_info = {
>> static const struct jz_soc_info jz4780_soc_info = {
>> 	.needs_dev_clk = true,
>> 	.has_osd = true,
>> +	.has_alpha = true,
>> 	.use_extended_hwdesc = true,
>> +	.plane_f0_not_working = true,	/* REVISIT */
>> 	.max_width = 4096,
>> 	.max_height = 2048,
>> 	.formats_f1 = jz4770_formats_f1,
>> --
>> 2.33.0
> 
> 

Re: [PATCH v14 5/9] drm/bridge: dw-hdmi: repair interworking with hdmi-connector for jz4780

[H. Nikolaus Schaller]

> Am 12.02.2022 um 16:06 schrieb Paul Cercueil <paul@crapouillou.net>:
> 
> Hi Nikolaus,
> 
> 
> Le sam., févr. 12 2022 at 15:19:23 +0100, H. Nikolaus Schaller <hns@goldelico.com> a écrit :
>> Commit 7cd70656d1285b ("drm/bridge: display-connector: implement bus fmts callbacks")
>> introduced a new mechanism to negotiate bus formats between hdmi connector
>> and the synopsys hdmi driver inside the jz4780.
>> By this, the dw-hdmi is no longer the only bridge and sets up a list
>> of formats in dw_hdmi_bridge_atomic_get_output_bus_fmts().
>> This includes MEDIA_BUS_FMT_UYVY8_1X16 which is chosen for the jz4780 but only
>> produces a black screen.
> 
> Neil pushed a fix yesterday that looks like it could fix your issue.
> The fix is: 1528038385c0 ("drm/bridge: dw-hdmi: use safe format when first in bridge chain")
> 
> Could you try if it does indeed fix your issue?

Sure.

Would have been nice and is a fix addressing same base commit, but is not a replacement for my attempt :(

Fortunately we can have both.

> 
> Cheers,
> -Paul
> 
>> This fix is based on the observation that max_bpc = 0 when running this
>> function while info->bpc = 8. Since the formats checks before this always test
>> for max_bpc >= info->pbc indirectly my assumption is that we must check it
>> here as well.
>> Adding the proposed patch makes the CI20/jz4780 panel work again in
>> MEDIA_BUS_FMT_RGB888_1X24 mode.
>> Fixes: 7cd70656d1285b ("drm/bridge: display-connector: implement bus fmts callbacks")
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> ---
>> drivers/gpu/drm/bridge/synopsys/dw-hdmi.c | 4 ++--
>> 1 file changed, 2 insertions(+), 2 deletions(-)
>> diff --git a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> index b0d8110dd412c..826a055a7a273 100644
>> --- a/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> +++ b/drivers/gpu/drm/bridge/synopsys/dw-hdmi.c
>> @@ -2620,10 +2620,10 @@ static u32 *dw_hdmi_bridge_atomic_get_output_bus_fmts(struct drm_bridge *bridge,
>> 		output_fmts[i++] = MEDIA_BUS_FMT_RGB101010_1X30;
>> 	}
>> -	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR422)
>> +	if (max_bpc >= info->bpc && info->color_formats & DRM_COLOR_FORMAT_YCBCR422)
>> 		output_fmts[i++] = MEDIA_BUS_FMT_UYVY8_1X16;
>> -	if (info->color_formats & DRM_COLOR_FORMAT_YCBCR444)
>> +	if (max_bpc >= info->bpc && info->color_formats & DRM_COLOR_FORMAT_YCBCR444)
>> 		output_fmts[i++] = MEDIA_BUS_FMT_YUV8_1X24;
>> 	/* Default 8bit RGB fallback */
>> --
>> 2.33.0
> 
> 

Re: [PATCH v14 8/9] [already applied to mips-fixes] MIPS: DTS: CI20: fix how ddc power is enabled

[H. Nikolaus Schaller]

> Am 12.02.2022 um 15:58 schrieb Paul Cercueil <paul@crapouillou.net>:
> 
> Hi,
> 
> Le sam., févr. 12 2022 at 15:19:26 +0100, H. Nikolaus Schaller <hns@goldelico.com> a écrit :
>> Originally we proposed a new hdmi-5v-supply regulator reference
>> for CI20 device tree but that was superseded by a better idea to use
>> the already defined "ddc-en-gpios" property of the "hdmi-connector".
>> Since "MIPS: DTS: CI20: Add DT nodes for HDMI setup" has already
>> been applied to v5.17-rc1, we add this on top.
>> Fixes: ae1b8d2c2de9 ("MIPS: DTS: CI20: Add DT nodes for HDMI setup")
>> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
>> Reviewed-by: Paul Cercueil <paul@crapouillou.net>
> 
> Since it's already applied you don't have to send this patch anymore.

I see, it has arrived in linux-next but not yet in drm-misc-next...
So if someone wants to test the series directly on top of drm-misc-next (as I am doing), it would be incomplete without.

IMHO these side-branches and partial merges here and there sometimes make more problems than they seem to solve...

But I leave already applied out commits for v15.

> 
> Cheers,
> -Paul
> 
>> ---
>> arch/mips/boot/dts/ingenic/ci20.dts | 15 ++-------------
>> 1 file changed, 2 insertions(+), 13 deletions(-)
>> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
>> index 3e336b3dbb109..ab6e3dc0bc1d0 100644
>> --- a/arch/mips/boot/dts/ingenic/ci20.dts
>> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
>> @@ -83,6 +83,8 @@ hdmi_out: connector {
>> 		label = "HDMI OUT";
>> 		type = "a";
>> +		ddc-en-gpios = <&gpa 25 GPIO_ACTIVE_HIGH>;
>> +
>> 		port {
>> 			hdmi_con: endpoint {
>> 				remote-endpoint = <&dw_hdmi_out>;
>> @@ -114,17 +116,6 @@ otg_power: fixedregulator@2 {
>> 		gpio = <&gpf 14 GPIO_ACTIVE_LOW>;
>> 		enable-active-high;
>> 	};
>> -
>> -	hdmi_power: fixedregulator@3 {
>> -		compatible = "regulator-fixed";
>> -
>> -		regulator-name = "hdmi_power";
>> -		regulator-min-microvolt = <5000000>;
>> -		regulator-max-microvolt = <5000000>;
>> -
>> -		gpio = <&gpa 25 0>;
>> -		enable-active-high;
>> -	};
>> };
>> &ext {
>> @@ -576,8 +567,6 @@ &hdmi {
>> 	pinctrl-names = "default";
>> 	pinctrl-0 = <&pins_hdmi_ddc>;
>> -	hdmi-5v-supply = <&hdmi_power>;
>> -
>> 	ports {
>> 		#address-cells = <1>;
>> 		#size-cells = <0>;
>> --
>> 2.33.0
> 
>