Re: [PATCH] Input: ili210x - Set the device name according to the device model

From: Marek Vasut <marex@denx.de>
To: Rogerio Pimentel <rpimentel.silva@gmail.com>
Cc: dmitry.torokhov@gmail.com, hansemro@outlook.com,
	linux-input@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH] Input: ili210x - Set the device name according to the device model
Date: Thu, 2 Sep 2021 14:44:03 +0200	[thread overview]
Message-ID: <2cf4320e-1111-2c2d-dc5a-92b171647450@denx.de> (raw)
In-Reply-To: <CAOkaPuVV3HK8OvVMQxjRPh1S_pFjvbEgsR-5UB51H8aguCw6Lw@mail.gmail.com>

On 9/2/21 2:39 PM, Rogerio Pimentel wrote:
> On Wed, Sep 1, 2021 at 5:48 PM Marek Vasut <marex@denx.de> wrote:
>>
>> On 9/1/21 10:27 PM, Rogerio Pimentel wrote:
>>> On Wed, Sep 1, 2021 at 4:46 PM Marek Vasut <marex@denx.de> wrote:
>>>>
>>>> On 9/1/21 9:22 PM, Rogerio Pimentel wrote:
>>>>
>>>> [...]
>>>>
>>>>> diff --git a/drivers/input/touchscreen/ili210x.c b/drivers/input/touchscreen/ili210x.c
>>>>> index 30576a5f2f04..ca7af4a6f588 100644
>>>>> --- a/drivers/input/touchscreen/ili210x.c
>>>>> +++ b/drivers/input/touchscreen/ili210x.c
>>>>> @@ -19,6 +19,8 @@
>>>>>     #define ILI251X_DATA_SIZE1  31
>>>>>     #define ILI251X_DATA_SIZE2  20
>>>>>
>>>>> +#define ILI_NAME_LEN         27
>>>>> +
>>>>>     /* Touchscreen commands */
>>>>>     #define REG_TOUCHDATA               0x10
>>>>>     #define REG_PANEL_INFO              0x20
>>>>> @@ -394,6 +396,7 @@ static int ili210x_i2c_probe(struct i2c_client *client,
>>>>>         struct input_dev *input;
>>>>>         int error;
>>>>>         unsigned int max_xy;
>>>>> +     char *model_name;
>>>>>
>>>>>         dev_dbg(dev, "Probing for ILI210X I2C Touschreen driver");
>>>>>
>>>>> @@ -440,7 +443,11 @@ static int ili210x_i2c_probe(struct i2c_client *client,
>>>>>         i2c_set_clientdata(client, priv);
>>>>>
>>>>>         /* Setup input device */
>>>>> -     input->name = "ILI210x Touchscreen";
>>>>> +     input->name = "Ilitek         Touchscreen";
>>>>> +     model_name = (char *)input->name;
>>>>> +     snprintf(model_name, ILI_NAME_LEN, "Ilitek %s Touchscreen",
>>>>
>>>> Which ilitek devices do you have available exactly ?
>>>>
>>>> There is a firmware interface which does report the device type, but I
>>>> don't know whether it works on all the ilitek touchscreen devices. If it
>>>> does, then it could be used here to pull the type from the firmware and
>>>> then use this instead
>>>>
>>>> snprintf(model_name, ILI_NAME_LEN, "Ilitek ILI%04x Touchscreen", type);
>>>>
>>>> Try this command against the touch controller, it sends it command 0x61
>>>> and reads two bytes of the reply:
>>>> i2ctransfer -f -y 1 w1@0x41 0x61 r2
>>>> 0x10 0x25 # <---- on ILI2510 it reports 0x25 0x10 in reverse
>>>
>>> Thanks for the comments and suggestions. I'll make the changes and send V2.
>>
>> Can you tell which ILI2xxx touch controller you have exactly ?
> 
> Now I have only the ILI2511. Will also have to support ILI2510 and ILI2118.
> 
>> Can you share the output of the 'i2ctransfer' (from i2c-tools) command
>> above ?
> 
> # i2ctransfer -f -y 3 w1@0x41 0x61 r2
> 0x11 0x25

Nice, so this works at least with the 251x series. Let's see how the 
2118 behaves, I bet you will get 0x18 0x21 there too.