[PATCH v4 00/38] DRM Rockchip rk3399 (Kevin)

[PATCH v4 00/38] DRM Rockchip rk3399 (Kevin)

[Enric Balletbo i Serra]

Hi,

This patchset includes cleanups, improvements, and bug fixes for
Rockchip DRM driver and PSR support.

This new version is the same as before but rebased on top of
drm-misc-next plus the Marek patches that fixes Chromebook2 Peach-Pit [1]
and the latest series of Rockchip rk3399 eDP support [2].

[1] https://www.spinics.net/lists/dri-devel/msg167804.html
[2] https://www.spinics.net/lists/dri-devel/msg167770.html

Regards,
 Enric

Changes in v4:
- Rebased all on top of drm-misc-next
- Removed the following patches as are already applied.
  [PATCH v3 01/43] drm/rockchip: Get rid of unnecessary struct fields
  [PATCH v3 02/43] drm/rockchip: support prime import sg table
  [PATCH v3 03/43] drm/rockchip: Respect page offset for PRIME mmap
  calls
- Removed the following patches as now are part of another patchset
  [PATCH v3 05/43] drm/bridge: analogix_dp: Don't power bridge in
  analogix_dp_bind
  [PATCH v3 33/43] drm/panel: simple: Change mode for Sharp lq123p1jx31

Changes in v3:
- Addressed some of the comments from Sean on the v2

Changes in v2:
- A few patches have been replaced by newer and cleaner versions from
  the ChromeOS kernel gerrit, especially about disallowing PSR for the
  whole atomic commit.


Douglas Anderson (4):
  drm/bridge: analogix_dp: Reorder plat_data->power_off to happen sooner
  drm/bridge: analogix_dp: Properly log AUX CH errors
  drm/bridge: analogix_dp: Properly disable aux chan retries on rockchip
  drm/bridge: analogix_dp: Split the platform-specific poweron in two
    parts

Kristian H. Kristensen (1):
  drm/rockchip: Disable PSR on input events

Lin Huang (6):
  drm/bridge: analogix_dp: Move enable video into config_video()
  drm/bridge: analogix_dp: Check AUX_EN status when doing AUX transfer
  drm/bridge: analogix_dp: Ensure edp is disabled when shutting down the
    panel
  drm/bridge: analogix_dp: Extend hpd check time to 100ms
  drm/bridge: analogix_dp: Check dpcd write/read status
  drm/bridge: analogix_dp: Reset aux channel if an error occurred

Mark Yao (1):
  drm/rockchip: pre dither down when output bpc is 8bit

Sean Paul (2):
  drm/rockchip: Don't use atomic constructs for psr
  drm/rockchip: Remove analogix psr worker

Tomasz Figa (7):
  drm/rockchip: analogix_dp: Do not call Analogix code before bind
  drm/rockchip: Cancel PSR enable work before changing the state
  drm/rockchip: psr: Avoid redundant calls to .set() callback
  drm/rockchip: psr: Sanitize semantics of allow/disallow API
  drm/rockchip: Disable PSR from reboot notifier
  drm/rockchip: Disallow PSR for the whole atomic commit
  drm/rockchip: psr: Remove flush by CRTC

Yakir Yang (1):
  drm/bridge: analogix_dp: detect Sink PSR state after configuring the
    PSR

zain wang (16):
  drm/bridge: analogix_dp: set psr activate/deactivate when
    enable/disable bridge
  drm/bridge: analogix_dp: Don't change psr while bridge is disabled
  drm/rockchip: add mutex vop lock
  drm/bridge: analogix_dp: add fast link train for eDP
  drm/rockchip: Only wait for panel ACK on PSR entry
  drm/bridge: analogix_dp: Don't use fast link training when panel just
    powered up
  drm/bridge: analogix_dp: Retry bridge enable when it failed
  drm/bridge: analogix_dp: Wait for HPD signal before configuring link
  drm/bridge: analogix_dp: Set PD_INC_BG first when powering up edp phy
  drm/bridge: analogix_dp: Fix incorrect usage of enhanced mode
  drm/bridge: analogix_dp: Fix AUX_PD bit for Rockchip
  drm/rockchip: Restore psr->state when enable/disable psr failed
  drm/bridge: analogix_dp: Don't use ANALOGIX_DP_PLL_CTL to control pll
  drm/bridge: analogix_dp: Fix timeout of video streamclk config
  drm/bridge: analogix_dp: Fix incorrect operations with register
    ANALOGIX_DP_FUNC_EN_1
  drm/bridge: analogix_dp: Move fast link training detect to set_bridge

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 452 ++++++++++++++++-----
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  14 +-
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 274 ++++++++-----
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h  |   7 +
 drivers/gpu/drm/exynos/exynos_dp.c                 |   2 +-
 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    |  73 ++--
 drivers/gpu/drm/rockchip/rockchip_drm_drv.c        |   2 +-
 drivers/gpu/drm/rockchip/rockchip_drm_drv.h        |   3 +-
 drivers/gpu/drm/rockchip/rockchip_drm_fb.c         |  61 ++-
 drivers/gpu/drm/rockchip/rockchip_drm_psr.c        | 361 ++++++++++------
 drivers/gpu/drm/rockchip/rockchip_drm_psr.h        |   7 +-
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c        |  47 ++-
 drivers/gpu/drm/rockchip/rockchip_drm_vop.h        |   1 +
 drivers/gpu/drm/rockchip/rockchip_vop_reg.c        |   1 +
 include/drm/bridge/analogix_dp.h                   |   5 +-
 15 files changed, 915 insertions(+), 395 deletions(-)

-- 
2.16.1

[PATCH v4 01/38] drm/bridge: analogix_dp: set psr activate/deactivate when enable/disable bridge

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

There's a race between when bridge_disable and when vop_crtc_disable
are called. If the flush timer triggers a new psr work between these,
we will operate eDP without power shutdowned by bridge_disable. In this
case, moving activate/deactivate to enable/disable bridge to avoid it.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c |  7 +++++-
 drivers/gpu/drm/rockchip/rockchip_drm_psr.c     | 30 ++++++++++++++++++++-----
 drivers/gpu/drm/rockchip/rockchip_drm_psr.h     |  4 ++--
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c     |  4 ----
 4 files changed, 32 insertions(+), 13 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index eb88c52336a7..7d76ff47028d 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -150,12 +150,17 @@ static int rockchip_dp_poweron(struct analogix_dp_plat_data *plat_data)
 		return ret;
 	}
 
-	return 0;
+	return rockchip_drm_psr_activate(&dp->encoder);
 }
 
 static int rockchip_dp_powerdown(struct analogix_dp_plat_data *plat_data)
 {
 	struct rockchip_dp_device *dp = to_dp(plat_data);
+	int ret;
+
+	ret = rockchip_drm_psr_deactivate(&dp->encoder);
+	if (ret != 0)
+		return ret;
 
 	clk_disable_unprepare(dp->pclk);
 
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
index 3acfd576b7df..b3fb99c5b1fd 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
@@ -57,6 +57,24 @@ static struct psr_drv *find_psr_by_crtc(struct drm_crtc *crtc)
 	return psr;
 }
 
+static struct psr_drv *find_psr_by_encoder(struct drm_encoder *encoder)
+{
+	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
+	struct psr_drv *psr;
+	unsigned long flags;
+
+	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	list_for_each_entry(psr, &drm_drv->psr_list, list) {
+		if (psr->encoder == encoder)
+			goto out;
+	}
+	psr = ERR_PTR(-ENODEV);
+
+out:
+	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	return psr;
+}
+
 static void psr_set_state_locked(struct psr_drv *psr, enum psr_state state)
 {
 	/*
@@ -115,14 +133,14 @@ static void psr_flush_handler(struct timer_list *t)
 
 /**
  * rockchip_drm_psr_activate - activate PSR on the given pipe
- * @crtc: CRTC to obtain the PSR encoder
+ * @encoder: encoder to obtain the PSR encoder
  *
  * Returns:
  * Zero on success, negative errno on failure.
  */
-int rockchip_drm_psr_activate(struct drm_crtc *crtc)
+int rockchip_drm_psr_activate(struct drm_encoder *encoder)
 {
-	struct psr_drv *psr = find_psr_by_crtc(crtc);
+	struct psr_drv *psr = find_psr_by_encoder(encoder);
 	unsigned long flags;
 
 	if (IS_ERR(psr))
@@ -138,14 +156,14 @@ EXPORT_SYMBOL(rockchip_drm_psr_activate);
 
 /**
  * rockchip_drm_psr_deactivate - deactivate PSR on the given pipe
- * @crtc: CRTC to obtain the PSR encoder
+ * @encoder: encoder to obtain the PSR encoder
  *
  * Returns:
  * Zero on success, negative errno on failure.
  */
-int rockchip_drm_psr_deactivate(struct drm_crtc *crtc)
+int rockchip_drm_psr_deactivate(struct drm_encoder *encoder)
 {
-	struct psr_drv *psr = find_psr_by_crtc(crtc);
+	struct psr_drv *psr = find_psr_by_encoder(encoder);
 	unsigned long flags;
 
 	if (IS_ERR(psr))
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.h b/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
index b420cf1bf902..b1ea0155e57c 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
@@ -18,8 +18,8 @@
 void rockchip_drm_psr_flush_all(struct drm_device *dev);
 int rockchip_drm_psr_flush(struct drm_crtc *crtc);
 
-int rockchip_drm_psr_activate(struct drm_crtc *crtc);
-int rockchip_drm_psr_deactivate(struct drm_crtc *crtc);
+int rockchip_drm_psr_activate(struct drm_encoder *encoder);
+int rockchip_drm_psr_deactivate(struct drm_encoder *encoder);
 
 int rockchip_drm_psr_register(struct drm_encoder *encoder,
 			void (*psr_set)(struct drm_encoder *, bool enable));
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index 9f72762532bf..63fbe789a5dd 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -569,8 +569,6 @@ static void vop_crtc_atomic_disable(struct drm_crtc *crtc,
 
 	WARN_ON(vop->event);
 
-	rockchip_drm_psr_deactivate(&vop->crtc);
-
 	drm_crtc_vblank_off(crtc);
 
 	/*
@@ -942,8 +940,6 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc,
 	clk_set_rate(vop->dclk, adjusted_mode->clock * 1000);
 
 	VOP_REG_SET(vop, common, standby, 0);
-
-	rockchip_drm_psr_activate(&vop->crtc);
 }
 
 static bool vop_fs_irq_is_pending(struct vop *vop)
-- 
2.16.1

[PATCH v4 02/38] drm/rockchip: Don't use atomic constructs for psr

[Enric Balletbo i Serra]

From: Sean Paul <seanpaul@chromium.org>

Instead of using timer and spinlocks, use delayed_work and
mutexes for rockchip psr. This allows us to make blocking
calls when enabling/disabling psr (which is sort of important
given we're talking over dpcd to the display).

Cc: Caesar Wang <wxt@rock-chips.com>
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/rockchip_drm_drv.c |  2 +-
 drivers/gpu/drm/rockchip/rockchip_drm_drv.h |  2 +-
 drivers/gpu/drm/rockchip/rockchip_drm_psr.c | 68 ++++++++++++-----------------
 3 files changed, 31 insertions(+), 41 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
index 1920334dbdaa..f814d37b1db2 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.c
@@ -134,7 +134,7 @@ static int rockchip_drm_bind(struct device *dev)
 	drm_dev->dev_private = private;
 
 	INIT_LIST_HEAD(&private->psr_list);
-	spin_lock_init(&private->psr_list_lock);
+	mutex_init(&private->psr_list_lock);
 
 	ret = rockchip_drm_init_iommu(drm_dev);
 	if (ret)
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
index 498dfbc52cec..9c064a40458b 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
@@ -55,7 +55,7 @@ struct rockchip_drm_private {
 	struct mutex mm_lock;
 	struct drm_mm mm;
 	struct list_head psr_list;
-	spinlock_t psr_list_lock;
+	struct mutex psr_list_lock;
 };
 
 int rockchip_drm_dma_attach_device(struct drm_device *drm_dev,
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
index b3fb99c5b1fd..b339ca943139 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
@@ -18,7 +18,7 @@
 #include "rockchip_drm_drv.h"
 #include "rockchip_drm_psr.h"
 
-#define PSR_FLUSH_TIMEOUT	msecs_to_jiffies(100)
+#define PSR_FLUSH_TIMEOUT_MS	100
 
 enum psr_state {
 	PSR_FLUSH,
@@ -30,11 +30,11 @@ struct psr_drv {
 	struct list_head	list;
 	struct drm_encoder	*encoder;
 
-	spinlock_t		lock;
+	struct mutex		lock;
 	bool			active;
 	enum psr_state		state;
 
-	struct timer_list	flush_timer;
+	struct delayed_work	flush_work;
 
 	void (*set)(struct drm_encoder *encoder, bool enable);
 };
@@ -43,9 +43,8 @@ static struct psr_drv *find_psr_by_crtc(struct drm_crtc *crtc)
 {
 	struct rockchip_drm_private *drm_drv = crtc->dev->dev_private;
 	struct psr_drv *psr;
-	unsigned long flags;
 
-	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	mutex_lock(&drm_drv->psr_list_lock);
 	list_for_each_entry(psr, &drm_drv->psr_list, list) {
 		if (psr->encoder->crtc == crtc)
 			goto out;
@@ -53,7 +52,7 @@ static struct psr_drv *find_psr_by_crtc(struct drm_crtc *crtc)
 	psr = ERR_PTR(-ENODEV);
 
 out:
-	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	mutex_unlock(&drm_drv->psr_list_lock);
 	return psr;
 }
 
@@ -61,9 +60,8 @@ static struct psr_drv *find_psr_by_encoder(struct drm_encoder *encoder)
 {
 	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
 	struct psr_drv *psr;
-	unsigned long flags;
 
-	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	mutex_lock(&drm_drv->psr_list_lock);
 	list_for_each_entry(psr, &drm_drv->psr_list, list) {
 		if (psr->encoder == encoder)
 			goto out;
@@ -71,7 +69,7 @@ static struct psr_drv *find_psr_by_encoder(struct drm_encoder *encoder)
 	psr = ERR_PTR(-ENODEV);
 
 out:
-	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	mutex_unlock(&drm_drv->psr_list_lock);
 	return psr;
 }
 
@@ -112,23 +110,21 @@ static void psr_set_state_locked(struct psr_drv *psr, enum psr_state state)
 
 static void psr_set_state(struct psr_drv *psr, enum psr_state state)
 {
-	unsigned long flags;
-
-	spin_lock_irqsave(&psr->lock, flags);
+	mutex_lock(&psr->lock);
 	psr_set_state_locked(psr, state);
-	spin_unlock_irqrestore(&psr->lock, flags);
+	mutex_unlock(&psr->lock);
 }
 
-static void psr_flush_handler(struct timer_list *t)
+static void psr_flush_handler(struct work_struct *work)
 {
-	struct psr_drv *psr = from_timer(psr, t, flush_timer);
-	unsigned long flags;
+	struct psr_drv *psr = container_of(to_delayed_work(work),
+					   struct psr_drv, flush_work);
 
 	/* If the state has changed since we initiated the flush, do nothing */
-	spin_lock_irqsave(&psr->lock, flags);
+	mutex_lock(&psr->lock);
 	if (psr->state == PSR_FLUSH)
 		psr_set_state_locked(psr, PSR_ENABLE);
-	spin_unlock_irqrestore(&psr->lock, flags);
+	mutex_unlock(&psr->lock);
 }
 
 /**
@@ -141,14 +137,13 @@ static void psr_flush_handler(struct timer_list *t)
 int rockchip_drm_psr_activate(struct drm_encoder *encoder)
 {
 	struct psr_drv *psr = find_psr_by_encoder(encoder);
-	unsigned long flags;
 
 	if (IS_ERR(psr))
 		return PTR_ERR(psr);
 
-	spin_lock_irqsave(&psr->lock, flags);
+	mutex_lock(&psr->lock);
 	psr->active = true;
-	spin_unlock_irqrestore(&psr->lock, flags);
+	mutex_unlock(&psr->lock);
 
 	return 0;
 }
@@ -164,15 +159,14 @@ EXPORT_SYMBOL(rockchip_drm_psr_activate);
 int rockchip_drm_psr_deactivate(struct drm_encoder *encoder)
 {
 	struct psr_drv *psr = find_psr_by_encoder(encoder);
-	unsigned long flags;
 
 	if (IS_ERR(psr))
 		return PTR_ERR(psr);
 
-	spin_lock_irqsave(&psr->lock, flags);
+	mutex_lock(&psr->lock);
 	psr->active = false;
-	spin_unlock_irqrestore(&psr->lock, flags);
-	del_timer_sync(&psr->flush_timer);
+	mutex_unlock(&psr->lock);
+	cancel_delayed_work_sync(&psr->flush_work);
 
 	return 0;
 }
@@ -180,9 +174,8 @@ EXPORT_SYMBOL(rockchip_drm_psr_deactivate);
 
 static void rockchip_drm_do_flush(struct psr_drv *psr)
 {
-	mod_timer(&psr->flush_timer,
-		  round_jiffies_up(jiffies + PSR_FLUSH_TIMEOUT));
 	psr_set_state(psr, PSR_FLUSH);
+	mod_delayed_work(system_wq, &psr->flush_work, PSR_FLUSH_TIMEOUT_MS);
 }
 
 /**
@@ -219,12 +212,11 @@ void rockchip_drm_psr_flush_all(struct drm_device *dev)
 {
 	struct rockchip_drm_private *drm_drv = dev->dev_private;
 	struct psr_drv *psr;
-	unsigned long flags;
 
-	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	mutex_lock(&drm_drv->psr_list_lock);
 	list_for_each_entry(psr, &drm_drv->psr_list, list)
 		rockchip_drm_do_flush(psr);
-	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	mutex_unlock(&drm_drv->psr_list_lock);
 }
 EXPORT_SYMBOL(rockchip_drm_psr_flush_all);
 
@@ -241,7 +233,6 @@ int rockchip_drm_psr_register(struct drm_encoder *encoder,
 {
 	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
 	struct psr_drv *psr;
-	unsigned long flags;
 
 	if (!encoder || !psr_set)
 		return -EINVAL;
@@ -250,17 +241,17 @@ int rockchip_drm_psr_register(struct drm_encoder *encoder,
 	if (!psr)
 		return -ENOMEM;
 
-	timer_setup(&psr->flush_timer, psr_flush_handler, 0);
-	spin_lock_init(&psr->lock);
+	INIT_DELAYED_WORK(&psr->flush_work, psr_flush_handler);
+	mutex_init(&psr->lock);
 
 	psr->active = true;
 	psr->state = PSR_DISABLE;
 	psr->encoder = encoder;
 	psr->set = psr_set;
 
-	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	mutex_lock(&drm_drv->psr_list_lock);
 	list_add_tail(&psr->list, &drm_drv->psr_list);
-	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	mutex_unlock(&drm_drv->psr_list_lock);
 
 	return 0;
 }
@@ -278,16 +269,15 @@ void rockchip_drm_psr_unregister(struct drm_encoder *encoder)
 {
 	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
 	struct psr_drv *psr, *n;
-	unsigned long flags;
 
-	spin_lock_irqsave(&drm_drv->psr_list_lock, flags);
+	mutex_lock(&drm_drv->psr_list_lock);
 	list_for_each_entry_safe(psr, n, &drm_drv->psr_list, list) {
 		if (psr->encoder == encoder) {
-			del_timer(&psr->flush_timer);
+			cancel_delayed_work_sync(&psr->flush_work);
 			list_del(&psr->list);
 			kfree(psr);
 		}
 	}
-	spin_unlock_irqrestore(&drm_drv->psr_list_lock, flags);
+	mutex_unlock(&drm_drv->psr_list_lock);
 }
 EXPORT_SYMBOL(rockchip_drm_psr_unregister);
-- 
2.16.1

[PATCH v4 03/38] drm/bridge: analogix_dp: detect Sink PSR state after configuring the PSR

[Enric Balletbo i Serra]

From: Yakir Yang <ykk@rock-chips.com>

Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c |  6 ++--
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  6 ++--
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 35 +++++++++++++++++++---
 3 files changed, 37 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index a693ab3078f0..e738aa6de1af 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -122,8 +122,7 @@ int analogix_dp_enable_psr(struct analogix_dp_device *dp)
 	psr_vsc.DB0 = 0;
 	psr_vsc.DB1 = EDP_VSC_PSR_STATE_ACTIVE | EDP_VSC_PSR_CRC_VALUES_VALID;
 
-	analogix_dp_send_psr_spd(dp, &psr_vsc);
-	return 0;
+	return analogix_dp_send_psr_spd(dp, &psr_vsc);
 }
 EXPORT_SYMBOL_GPL(analogix_dp_enable_psr);
 
@@ -149,8 +148,7 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
 	if (ret != 1)
 		dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret);
 
-	analogix_dp_send_psr_spd(dp, &psr_vsc);
-	return 0;
+	return analogix_dp_send_psr_spd(dp, &psr_vsc);
 }
 EXPORT_SYMBOL_GPL(analogix_dp_disable_psr);
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index 5c6a28806129..b039b28d8fcc 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -20,6 +20,8 @@
 #define MAX_CR_LOOP 5
 #define MAX_EQ_LOOP 5
 
+#define DP_TIMEOUT_PSR_LOOP_MS			300
+
 /* DP_MAX_LANE_COUNT */
 #define DPCD_ENHANCED_FRAME_CAP(x)		(((x) >> 7) & 0x1)
 #define DPCD_MAX_LANE_COUNT(x)			((x) & 0x1f)
@@ -247,8 +249,8 @@ void analogix_dp_config_video_slave_mode(struct analogix_dp_device *dp);
 void analogix_dp_enable_scrambling(struct analogix_dp_device *dp);
 void analogix_dp_disable_scrambling(struct analogix_dp_device *dp);
 void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp);
-void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
-			      struct edp_vsc_psr *vsc);
+int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
+			     struct edp_vsc_psr *vsc);
 ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 			     struct drm_dp_aux_msg *msg);
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 303083ad28e3..005a3f7005d2 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -10,10 +10,11 @@
  * option) any later version.
  */
 
-#include <linux/device.h>
-#include <linux/io.h>
 #include <linux/delay.h>
+#include <linux/device.h>
 #include <linux/gpio.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
 
 #include <drm/bridge/analogix_dp.h>
 
@@ -992,10 +993,25 @@ void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp)
 	writel(PSR_VID_CRC_ENABLE, dp->reg_base + ANALOGIX_DP_CRC_CON);
 }
 
-void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
-			      struct edp_vsc_psr *vsc)
+static ssize_t analogix_dp_get_psr_status(struct analogix_dp_device *dp)
+{
+	ssize_t val;
+	u8 status;
+
+	val = drm_dp_dpcd_readb(&dp->aux, DP_PSR_STATUS, &status);
+	if (val < 0) {
+		dev_err(dp->dev, "PSR_STATUS read failed ret=%zd", val);
+		return val;
+	}
+	return status;
+}
+
+int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
+			     struct edp_vsc_psr *vsc)
 {
 	unsigned int val;
+	int ret;
+	ssize_t psr_status;
 
 	/* don't send info frame */
 	val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
@@ -1036,6 +1052,17 @@ void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
 	val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
 	val |= IF_EN;
 	writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
+
+	ret = readx_poll_timeout(analogix_dp_get_psr_status, dp, psr_status,
+		psr_status >= 0 &&
+		((vsc->DB1 && psr_status == DP_PSR_SINK_ACTIVE_RFB) ||
+		(!vsc->DB1 && psr_status == DP_PSR_SINK_INACTIVE)), 1500,
+		DP_TIMEOUT_PSR_LOOP_MS * 1000);
+	if (ret) {
+		dev_warn(dp->dev, "Failed to apply PSR %d\n", ret);
+		return ret;
+	}
+	return 0;
 }
 
 ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
-- 
2.16.1

[PATCH v4 04/38] drm/rockchip: Remove analogix psr worker

[Enric Balletbo i Serra]

From: Sean Paul <seanpaul@chromium.org>

Now that the spinlocks and timers are gone, we can remove the psr
worker located in rockchip's analogix driver and do the enable/disable
directly. This should simplify the code and remove races on disable.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c | 31 ++-----------------------
 1 file changed, 2 insertions(+), 29 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index 7d76ff47028d..36334839a3f8 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -71,10 +71,6 @@ struct rockchip_dp_device {
 	struct regmap            *grf;
 	struct reset_control     *rst;
 
-	struct work_struct	 psr_work;
-	struct mutex             psr_lock;
-	unsigned int             psr_state;
-
 	const struct rockchip_dp_chip_data *data;
 
 	struct analogix_dp_device *adp;
@@ -84,28 +80,13 @@ struct rockchip_dp_device {
 static void analogix_dp_psr_set(struct drm_encoder *encoder, bool enabled)
 {
 	struct rockchip_dp_device *dp = to_dp(encoder);
+	int ret;
 
 	if (!analogix_dp_psr_supported(dp->adp))
 		return;
 
 	DRM_DEV_DEBUG(dp->dev, "%s PSR...\n", enabled ? "Entry" : "Exit");
 
-	mutex_lock(&dp->psr_lock);
-	if (enabled)
-		dp->psr_state = EDP_VSC_PSR_STATE_ACTIVE;
-	else
-		dp->psr_state = ~EDP_VSC_PSR_STATE_ACTIVE;
-
-	schedule_work(&dp->psr_work);
-	mutex_unlock(&dp->psr_lock);
-}
-
-static void analogix_dp_psr_work(struct work_struct *work)
-{
-	struct rockchip_dp_device *dp =
-				container_of(work, typeof(*dp), psr_work);
-	int ret;
-
 	ret = rockchip_drm_wait_vact_end(dp->encoder.crtc,
 					 PSR_WAIT_LINE_FLAG_TIMEOUT_MS);
 	if (ret) {
@@ -113,12 +94,10 @@ static void analogix_dp_psr_work(struct work_struct *work)
 		return;
 	}
 
-	mutex_lock(&dp->psr_lock);
-	if (dp->psr_state == EDP_VSC_PSR_STATE_ACTIVE)
+	if (enabled)
 		analogix_dp_enable_psr(dp->adp);
 	else
 		analogix_dp_disable_psr(dp->adp);
-	mutex_unlock(&dp->psr_lock);
 }
 
 static int rockchip_dp_pre_init(struct rockchip_dp_device *dp)
@@ -135,8 +114,6 @@ static int rockchip_dp_poweron(struct analogix_dp_plat_data *plat_data)
 	struct rockchip_dp_device *dp = to_dp(plat_data);
 	int ret;
 
-	cancel_work_sync(&dp->psr_work);
-
 	ret = clk_prepare_enable(dp->pclk);
 	if (ret < 0) {
 		DRM_DEV_ERROR(dp->dev, "failed to enable pclk %d\n", ret);
@@ -355,10 +332,6 @@ static int rockchip_dp_bind(struct device *dev, struct device *master,
 	dp->plat_data.power_off = rockchip_dp_powerdown;
 	dp->plat_data.get_modes = rockchip_dp_get_modes;
 
-	mutex_init(&dp->psr_lock);
-	dp->psr_state = ~EDP_VSC_PSR_STATE_ACTIVE;
-	INIT_WORK(&dp->psr_work, analogix_dp_psr_work);
-
 	ret = rockchip_drm_psr_register(&dp->encoder, analogix_dp_psr_set);
 	if (ret < 0)
 		goto err_cleanup_encoder;
-- 
2.16.1

[PATCH v4 05/38] drm/bridge: analogix_dp: Don't change psr while bridge is disabled

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.

Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 15 ++++++++-------
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  2 +-
 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    |  2 +-
 include/drm/bridge/analogix_dp.h                   |  2 +-
 4 files changed, 11 insertions(+), 10 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index e738aa6de1af..ee00d3d920e0 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -98,18 +98,18 @@ static int analogix_dp_detect_hpd(struct analogix_dp_device *dp)
 	return 0;
 }
 
-int analogix_dp_psr_supported(struct analogix_dp_device *dp)
+int analogix_dp_psr_enabled(struct analogix_dp_device *dp)
 {
 
-	return dp->psr_support;
+	return dp->psr_enable;
 }
-EXPORT_SYMBOL_GPL(analogix_dp_psr_supported);
+EXPORT_SYMBOL_GPL(analogix_dp_psr_enabled);
 
 int analogix_dp_enable_psr(struct analogix_dp_device *dp)
 {
 	struct edp_vsc_psr psr_vsc;
 
-	if (!dp->psr_support)
+	if (!dp->psr_enable)
 		return 0;
 
 	/* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */
@@ -131,7 +131,7 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
 	struct edp_vsc_psr psr_vsc;
 	int ret;
 
-	if (!dp->psr_support)
+	if (!dp->psr_enable)
 		return 0;
 
 	/* Prepare VSC packet as per EDP 1.4 spec, Table 6.9 */
@@ -871,8 +871,8 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
 	/* Enable video */
 	analogix_dp_start_video(dp);
 
-	dp->psr_support = analogix_dp_detect_sink_psr(dp);
-	if (dp->psr_support)
+	dp->psr_enable = analogix_dp_detect_sink_psr(dp);
+	if (dp->psr_enable)
 		analogix_dp_enable_sink_psr(dp);
 }
 
@@ -1117,6 +1117,7 @@ static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
 	if (ret)
 		DRM_ERROR("failed to setup the panel ret = %d\n", ret);
 
+	dp->psr_enable = false;
 	dp->dpms_mode = DRM_MODE_DPMS_OFF;
 }
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index b039b28d8fcc..e135a42cb19e 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -170,7 +170,7 @@ struct analogix_dp_device {
 	int			dpms_mode;
 	int			hpd_gpio;
 	bool                    force_hpd;
-	bool			psr_support;
+	bool			psr_enable;
 
 	struct mutex		panel_lock;
 	bool			panel_is_modeset;
diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index 36334839a3f8..3e8bf79bea58 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -82,7 +82,7 @@ static void analogix_dp_psr_set(struct drm_encoder *encoder, bool enabled)
 	struct rockchip_dp_device *dp = to_dp(encoder);
 	int ret;
 
-	if (!analogix_dp_psr_supported(dp->adp))
+	if (!analogix_dp_psr_enabled(dp->adp))
 		return;
 
 	DRM_DEV_DEBUG(dp->dev, "%s PSR...\n", enabled ? "Entry" : "Exit");
diff --git a/include/drm/bridge/analogix_dp.h b/include/drm/bridge/analogix_dp.h
index 711fff9b6803..e9a1116d2f8e 100644
--- a/include/drm/bridge/analogix_dp.h
+++ b/include/drm/bridge/analogix_dp.h
@@ -41,7 +41,7 @@ struct analogix_dp_plat_data {
 			 struct drm_connector *);
 };
 
-int analogix_dp_psr_supported(struct analogix_dp_device *dp);
+int analogix_dp_psr_enabled(struct analogix_dp_device *dp);
 int analogix_dp_enable_psr(struct analogix_dp_device *dp);
 int analogix_dp_disable_psr(struct analogix_dp_device *dp);
 
-- 
2.16.1

[PATCH v4 06/38] drm/rockchip: add mutex vop lock

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

Add a lock to vop to avoid disabling the crtc while waiting for a line
flag while enabling psr. If we disable in the middle of waiting for the
line flag, we'll end up timing out or worse.

Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 30 +++++++++++++++++++++++------
 1 file changed, 24 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index 63fbe789a5dd..184f980679af 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -117,6 +117,8 @@ struct vop {
 	spinlock_t reg_lock;
 	/* lock vop irq reg */
 	spinlock_t irq_lock;
+	/* protects crtc enable/disable */
+	struct mutex vop_lock;
 
 	unsigned int irq;
 
@@ -569,6 +571,7 @@ static void vop_crtc_atomic_disable(struct drm_crtc *crtc,
 
 	WARN_ON(vop->event);
 
+	mutex_lock(&vop->vop_lock);
 	drm_crtc_vblank_off(crtc);
 
 	/*
@@ -604,6 +607,7 @@ static void vop_crtc_atomic_disable(struct drm_crtc *crtc,
 	clk_disable(vop->aclk);
 	clk_disable(vop->hclk);
 	pm_runtime_put(vop->dev);
+	mutex_unlock(&vop->vop_lock);
 
 	if (crtc->state->event && !crtc->state->active) {
 		spin_lock_irq(&crtc->dev->event_lock);
@@ -873,10 +877,13 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc,
 	uint32_t pin_pol, val;
 	int ret;
 
+	mutex_lock(&vop->vop_lock);
+
 	WARN_ON(vop->event);
 
 	ret = vop_enable(crtc);
 	if (ret) {
+		mutex_unlock(&vop->vop_lock);
 		DRM_DEV_ERROR(vop->dev, "Failed to enable vop (%d)\n", ret);
 		return;
 	}
@@ -940,6 +947,7 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc,
 	clk_set_rate(vop->dclk, adjusted_mode->clock * 1000);
 
 	VOP_REG_SET(vop, common, standby, 0);
+	mutex_unlock(&vop->vop_lock);
 }
 
 static bool vop_fs_irq_is_pending(struct vop *vop)
@@ -1478,15 +1486,21 @@ int rockchip_drm_wait_vact_end(struct drm_crtc *crtc, unsigned int mstimeout)
 {
 	struct vop *vop = to_vop(crtc);
 	unsigned long jiffies_left;
+	int ret = 0;
 
 	if (!crtc || !vop->is_enabled)
 		return -ENODEV;
 
-	if (mstimeout <= 0)
-		return -EINVAL;
+	mutex_lock(&vop->vop_lock);
+	if (mstimeout <= 0) {
+		ret = -EINVAL;
+		goto out;
+	}
 
-	if (vop_line_flag_irq_is_enabled(vop))
-		return -EBUSY;
+	if (vop_line_flag_irq_is_enabled(vop)) {
+		ret = -EBUSY;
+		goto out;
+	}
 
 	reinit_completion(&vop->line_flag_completion);
 	vop_line_flag_irq_enable(vop);
@@ -1497,10 +1511,13 @@ int rockchip_drm_wait_vact_end(struct drm_crtc *crtc, unsigned int mstimeout)
 
 	if (jiffies_left == 0) {
 		DRM_DEV_ERROR(vop->dev, "Timeout waiting for IRQ\n");
-		return -ETIMEDOUT;
+		ret = -ETIMEDOUT;
+		goto out;
 	}
 
-	return 0;
+out:
+	mutex_unlock(&vop->vop_lock);
+	return ret;
 }
 EXPORT_SYMBOL(rockchip_drm_wait_vact_end);
 
@@ -1550,6 +1567,7 @@ static int vop_bind(struct device *dev, struct device *master, void *data)
 
 	spin_lock_init(&vop->reg_lock);
 	spin_lock_init(&vop->irq_lock);
+	mutex_init(&vop->vop_lock);
 
 	ret = devm_request_irq(dev, vop->irq, vop_isr,
 			       IRQF_SHARED, dev_name(dev), vop);
-- 
2.16.1

[PATCH v4 07/38] drm/bridge: analogix_dp: add fast link train for eDP

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

We would meet a short black screen when exit PSR with the full link
training, In this case, we should use fast link train instead of full
link training.

Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 142 ++++++++++++++++-----
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |   3 +
 2 files changed, 114 insertions(+), 31 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index ee00d3d920e0..806c3878b3d6 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -10,17 +10,18 @@
 * option) any later version.
 */
 
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/err.h>
 #include <linux/clk.h>
-#include <linux/io.h>
+#include <linux/component.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
 #include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_gpio.h>
-#include <linux/gpio.h>
-#include <linux/component.h>
 #include <linux/phy/phy.h>
+#include <linux/platform_device.h>
 
 #include <drm/drmP.h>
 #include <drm/drm_atomic_helper.h>
@@ -35,6 +36,8 @@
 
 #define to_dp(nm)	container_of(nm, struct analogix_dp_device, nm)
 
+static const bool verify_fast_training;
+
 struct bridge_init {
 	struct i2c_client *client;
 	struct device_node *node;
@@ -528,7 +531,7 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 {
 	int lane, lane_count, retval;
 	u32 reg;
-	u8 link_align, link_status[2], adjust_request[2];
+	u8 link_align, link_status[2], adjust_request[2], spread;
 
 	usleep_range(400, 401);
 
@@ -571,6 +574,20 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 		dev_dbg(dp->dev, "final lane count = %.2x\n",
 			dp->link_train.lane_count);
 
+		retval = drm_dp_dpcd_readb(&dp->aux, DP_MAX_DOWNSPREAD,
+					   &spread);
+		if (retval != 1) {
+			dev_err(dp->dev, "failed to read downspread %d\n",
+				retval);
+			dp->fast_train_support = false;
+		} else {
+			dp->fast_train_support =
+				(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING) ?
+					true : false;
+		}
+		dev_dbg(dp->dev, "fast link training %s\n",
+			dp->fast_train_support ? "supported" : "unsupported");
+
 		/* set enhanced mode if available */
 		analogix_dp_set_enhanced_mode(dp);
 		dp->link_train.lt_state = FINISHED;
@@ -627,10 +644,12 @@ static void analogix_dp_get_max_rx_lane_count(struct analogix_dp_device *dp,
 	*lane_count = DPCD_MAX_LANE_COUNT(data);
 }
 
-static void analogix_dp_init_training(struct analogix_dp_device *dp,
-				      enum link_lane_count_type max_lane,
-				      int max_rate)
+static int analogix_dp_full_link_train(struct analogix_dp_device *dp,
+				       u32 max_lanes, u32 max_rate)
 {
+	int retval = 0;
+	bool training_finished = false;
+
 	/*
 	 * MACRO_RST must be applied after the PLL_LOCK to avoid
 	 * the DP inter pair skew issue for at least 10 us
@@ -656,18 +675,13 @@ static void analogix_dp_init_training(struct analogix_dp_device *dp,
 	}
 
 	/* Setup TX lane count & rate */
-	if (dp->link_train.lane_count > max_lane)
-		dp->link_train.lane_count = max_lane;
+	if (dp->link_train.lane_count > max_lanes)
+		dp->link_train.lane_count = max_lanes;
 	if (dp->link_train.link_rate > max_rate)
 		dp->link_train.link_rate = max_rate;
 
 	/* All DP analog module power up */
 	analogix_dp_set_analog_power_down(dp, POWER_ALL, 0);
-}
-
-static int analogix_dp_sw_link_training(struct analogix_dp_device *dp)
-{
-	int retval = 0, training_finished = 0;
 
 	dp->link_train.lt_state = START;
 
@@ -702,22 +716,88 @@ static int analogix_dp_sw_link_training(struct analogix_dp_device *dp)
 	return retval;
 }
 
-static int analogix_dp_set_link_train(struct analogix_dp_device *dp,
-				      u32 count, u32 bwtype)
+static int analogix_dp_fast_link_train(struct analogix_dp_device *dp)
 {
-	int i;
-	int retval;
+	int i, ret;
+	u8 link_align, link_status[2];
+	enum pll_status status;
 
-	for (i = 0; i < DP_TIMEOUT_LOOP_COUNT; i++) {
-		analogix_dp_init_training(dp, count, bwtype);
-		retval = analogix_dp_sw_link_training(dp);
-		if (retval == 0)
-			break;
+	analogix_dp_reset_macro(dp);
+
+	analogix_dp_set_link_bandwidth(dp, dp->link_train.link_rate);
+	analogix_dp_set_lane_count(dp, dp->link_train.lane_count);
 
-		usleep_range(100, 110);
+	for (i = 0; i < dp->link_train.lane_count; i++) {
+		analogix_dp_set_lane_link_training(dp,
+			dp->link_train.training_lane[i], i);
 	}
 
-	return retval;
+	ret = readx_poll_timeout(analogix_dp_get_pll_lock_status, dp, status,
+				 status != PLL_UNLOCKED, 120,
+				 120 * DP_TIMEOUT_LOOP_COUNT);
+	if (ret) {
+		DRM_DEV_ERROR(dp->dev, "Wait for pll lock failed %d\n", ret);
+		return ret;
+	}
+
+	/* source Set training pattern 1 */
+	analogix_dp_set_training_pattern(dp, TRAINING_PTN1);
+	/* From DP spec, pattern must be on-screen for a minimum 500us */
+	usleep_range(500, 600);
+
+	analogix_dp_set_training_pattern(dp, TRAINING_PTN2);
+	/* From DP spec, pattern must be on-screen for a minimum 500us */
+	usleep_range(500, 600);
+
+	/* TODO: enhanced_mode?*/
+	analogix_dp_set_training_pattern(dp, DP_NONE);
+
+	/*
+	 * Useful for debugging issues with fast link training, disable for more
+	 * speed
+	 */
+	if (verify_fast_training) {
+		ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_ALIGN_STATUS_UPDATED,
+					&link_align);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dp->dev, "Read align status failed %d\n",
+				      ret);
+			return ret;
+		}
+
+		ret = drm_dp_dpcd_read(&dp->aux, DP_LANE0_1_STATUS, link_status,
+				       2);
+		if (ret < 0) {
+			DRM_DEV_ERROR(dp->dev, "Read link status failed %d\n",
+				      ret);
+			return ret;
+		}
+
+		if (analogix_dp_clock_recovery_ok(link_status,
+						  dp->link_train.lane_count)) {
+			DRM_DEV_ERROR(dp->dev, "Clock recovery failed\n");
+			analogix_dp_reduce_link_rate(dp);
+			return -EIO;
+		}
+
+		if (analogix_dp_channel_eq_ok(link_status, link_align,
+					      dp->link_train.lane_count)) {
+			DRM_DEV_ERROR(dp->dev, "Channel EQ failed\n");
+			analogix_dp_reduce_link_rate(dp);
+			return -EIO;
+		}
+	}
+
+	return 0;
+}
+
+static int analogix_dp_train_link(struct analogix_dp_device *dp)
+{
+	if (dp->fast_train_support)
+		return analogix_dp_fast_link_train(dp);
+
+	return analogix_dp_full_link_train(dp, dp->video_info.max_lane_count,
+					   dp->video_info.max_link_rate);
 }
 
 static int analogix_dp_config_video(struct analogix_dp_device *dp)
@@ -846,10 +926,10 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
 			DRM_ERROR("failed to disable the panel\n");
 	}
 
-	ret = analogix_dp_set_link_train(dp, dp->video_info.max_lane_count,
-					 dp->video_info.max_link_rate);
+	ret = readx_poll_timeout(analogix_dp_train_link, dp, ret, !ret, 100,
+				 DP_TIMEOUT_TRAINING_US * 5);
 	if (ret) {
-		dev_err(dp->dev, "unable to do link train\n");
+		dev_err(dp->dev, "unable to do link train, ret=%d\n", ret);
 		return;
 	}
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index e135a42cb19e..920607d7eb3e 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -20,6 +20,8 @@
 #define MAX_CR_LOOP 5
 #define MAX_EQ_LOOP 5
 
+/* Training takes 22ms if AUX channel comm fails. Use this as retry interval */
+#define DP_TIMEOUT_TRAINING_US			22000
 #define DP_TIMEOUT_PSR_LOOP_MS			300
 
 /* DP_MAX_LANE_COUNT */
@@ -171,6 +173,7 @@ struct analogix_dp_device {
 	int			hpd_gpio;
 	bool                    force_hpd;
 	bool			psr_enable;
+	bool			fast_train_support;
 
 	struct mutex		panel_lock;
 	bool			panel_is_modeset;
-- 
2.16.1

[PATCH v4 08/38] drm/rockchip: Only wait for panel ACK on PSR entry

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).

This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 4 ++--
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 2 +-
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 5 ++++-
 3 files changed, 7 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 806c3878b3d6..5a2e35dc41e3 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -125,7 +125,7 @@ int analogix_dp_enable_psr(struct analogix_dp_device *dp)
 	psr_vsc.DB0 = 0;
 	psr_vsc.DB1 = EDP_VSC_PSR_STATE_ACTIVE | EDP_VSC_PSR_CRC_VALUES_VALID;
 
-	return analogix_dp_send_psr_spd(dp, &psr_vsc);
+	return analogix_dp_send_psr_spd(dp, &psr_vsc, true);
 }
 EXPORT_SYMBOL_GPL(analogix_dp_enable_psr);
 
@@ -151,7 +151,7 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
 	if (ret != 1)
 		dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret);
 
-	return analogix_dp_send_psr_spd(dp, &psr_vsc);
+	return analogix_dp_send_psr_spd(dp, &psr_vsc, false);
 }
 EXPORT_SYMBOL_GPL(analogix_dp_disable_psr);
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index 920607d7eb3e..6a96ef7e6934 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -253,7 +253,7 @@ void analogix_dp_enable_scrambling(struct analogix_dp_device *dp);
 void analogix_dp_disable_scrambling(struct analogix_dp_device *dp);
 void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp);
 int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
-			     struct edp_vsc_psr *vsc);
+			     struct edp_vsc_psr *vsc, bool blocking);
 ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 			     struct drm_dp_aux_msg *msg);
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 005a3f7005d2..9df2f3ef000c 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -1007,7 +1007,7 @@ static ssize_t analogix_dp_get_psr_status(struct analogix_dp_device *dp)
 }
 
 int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
-			     struct edp_vsc_psr *vsc)
+			     struct edp_vsc_psr *vsc, bool blocking)
 {
 	unsigned int val;
 	int ret;
@@ -1053,6 +1053,9 @@ int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
 	val |= IF_EN;
 	writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
 
+	if (!blocking)
+		return 0;
+
 	ret = readx_poll_timeout(analogix_dp_get_psr_status, dp, psr_status,
 		psr_status >= 0 &&
 		((vsc->DB1 && psr_status == DP_PSR_SINK_ACTIVE_RFB) ||
-- 
2.16.1

[PATCH v4 09/38] drm/bridge: analogix_dp: Move enable video into config_video()

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

We need to enable video before analogix_dp_is_video_stream_on(), so
we can get the right video stream status.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 11 +++++------
 1 file changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 5a2e35dc41e3..f9661b410cb9 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -819,11 +819,10 @@ static int analogix_dp_config_video(struct analogix_dp_device *dp)
 		if (analogix_dp_is_slave_video_stream_clock_on(dp) == 0)
 			break;
 		if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) {
-			dev_err(dp->dev, "Timeout of video streamclk ok\n");
+			dev_err(dp->dev, "Timeout of slave video streamclk ok\n");
 			return -ETIMEDOUT;
 		}
-
-		usleep_range(1, 2);
+		usleep_range(1000, 1001);
 	}
 
 	/* Set to use the register calculated M/N video */
@@ -838,6 +837,9 @@ static int analogix_dp_config_video(struct analogix_dp_device *dp)
 	/* Configure video slave mode */
 	analogix_dp_enable_video_master(dp, 0);
 
+	/* Enable video */
+	analogix_dp_start_video(dp);
+
 	timeout_loop = 0;
 
 	for (;;) {
@@ -948,9 +950,6 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
 			DRM_ERROR("failed to enable the panel\n");
 	}
 
-	/* Enable video */
-	analogix_dp_start_video(dp);
-
 	dp->psr_enable = analogix_dp_detect_sink_psr(dp);
 	if (dp->psr_enable)
 		analogix_dp_enable_sink_psr(dp);
-- 
2.16.1

[PATCH v4 10/38] drm/bridge: analogix_dp: Check AUX_EN status when doing AUX transfer

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

We should check AUX_EN bit to confirm the AUX CH operation is completed.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 25 +++++++++++++----------
 1 file changed, 14 insertions(+), 11 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 9df2f3ef000c..e78c861b9e06 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -1073,9 +1073,9 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 {
 	u32 reg;
 	u8 *buffer = msg->buffer;
-	int timeout_loop = 0;
 	unsigned int i;
 	int num_transferred = 0;
+	int ret;
 
 	/* Buffer size of AUX CH is 16 bytes */
 	if (WARN_ON(msg->size > 16))
@@ -1139,17 +1139,20 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 
 	writel(reg, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2);
 
-	/* Is AUX CH command reply received? */
+	ret = readx_poll_timeout(readl, dp->reg_base + ANALOGIX_DP_AUX_CH_CTL_2,
+				 reg, !(reg & AUX_EN), 25, 500 * 1000);
+	if (ret) {
+		dev_err(dp->dev, "AUX CH enable timeout!\n");
+		return -ETIMEDOUT;
+	}
+
 	/* TODO: Wait for an interrupt instead of looping? */
-	reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA);
-	while (!(reg & RPLY_RECEIV)) {
-		timeout_loop++;
-		if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) {
-			dev_err(dp->dev, "AUX CH command reply failed!\n");
-			return -ETIMEDOUT;
-		}
-		reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA);
-		usleep_range(10, 11);
+	/* Is AUX CH command reply received? */
+	ret = readx_poll_timeout(readl, dp->reg_base + ANALOGIX_DP_INT_STA,
+				 reg, reg & RPLY_RECEIV, 10, 20 * 1000);
+	if (ret) {
+		dev_err(dp->dev, "AUX CH cmd reply timeout!\n");
+		return -ETIMEDOUT;
 	}
 
 	/* Clear interrupt source for AUX CH command reply */
-- 
2.16.1

[PATCH v4 11/38] drm/bridge: analogix_dp: Don't use fast link training when panel just powered up

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

Panel would reset its setting when it powers down. It would forget the last
succeeded link training setting. So we can't use the last successful link
training setting to do fast link training. Let's reset fast_train_enable in
analogix_dp_bridge_disable();

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 9 +++++----
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 2 +-
 2 files changed, 6 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index f9661b410cb9..ea7a80a989c6 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -579,14 +579,14 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 		if (retval != 1) {
 			dev_err(dp->dev, "failed to read downspread %d\n",
 				retval);
-			dp->fast_train_support = false;
+			dp->fast_train_enable = false;
 		} else {
-			dp->fast_train_support =
+			dp->fast_train_enable =
 				(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING) ?
 					true : false;
 		}
 		dev_dbg(dp->dev, "fast link training %s\n",
-			dp->fast_train_support ? "supported" : "unsupported");
+			dp->fast_train_enable ? "supported" : "unsupported");
 
 		/* set enhanced mode if available */
 		analogix_dp_set_enhanced_mode(dp);
@@ -793,7 +793,7 @@ static int analogix_dp_fast_link_train(struct analogix_dp_device *dp)
 
 static int analogix_dp_train_link(struct analogix_dp_device *dp)
 {
-	if (dp->fast_train_support)
+	if (dp->fast_train_enable)
 		return analogix_dp_fast_link_train(dp);
 
 	return analogix_dp_full_link_train(dp, dp->video_info.max_lane_count,
@@ -1197,6 +1197,7 @@ static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
 		DRM_ERROR("failed to setup the panel ret = %d\n", ret);
 
 	dp->psr_enable = false;
+	dp->fast_train_enable = false;
 	dp->dpms_mode = DRM_MODE_DPMS_OFF;
 }
 
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index 6a96ef7e6934..403ff853464b 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -173,7 +173,7 @@ struct analogix_dp_device {
 	int			hpd_gpio;
 	bool                    force_hpd;
 	bool			psr_enable;
-	bool			fast_train_support;
+	bool			fast_train_enable;
 
 	struct mutex		panel_lock;
 	bool			panel_is_modeset;
-- 
2.16.1

[PATCH v4 12/38] drm/bridge: analogix_dp: Retry bridge enable when it failed

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 65 +++++++++++++++++-----
 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  3 +-
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  |  5 +-
 3 files changed, 56 insertions(+), 17 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index ea7a80a989c6..c81733b8185e 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -43,8 +43,10 @@ struct bridge_init {
 	struct device_node *node;
 };
 
-static void analogix_dp_init_dp(struct analogix_dp_device *dp)
+static int analogix_dp_init_dp(struct analogix_dp_device *dp)
 {
+	int ret;
+
 	analogix_dp_reset(dp);
 
 	analogix_dp_swreset(dp);
@@ -56,10 +58,13 @@ static void analogix_dp_init_dp(struct analogix_dp_device *dp)
 	analogix_dp_enable_sw_function(dp);
 
 	analogix_dp_config_interrupt(dp);
-	analogix_dp_init_analog_func(dp);
+	ret = analogix_dp_init_analog_func(dp);
+	if (ret)
+		return ret;
 
 	analogix_dp_init_hpd(dp);
 	analogix_dp_init_aux(dp);
+	return 0;
 }
 
 static int analogix_dp_detect_hpd(struct analogix_dp_device *dp)
@@ -918,7 +923,7 @@ static irqreturn_t analogix_dp_irq_thread(int irq, void *arg)
 	return IRQ_HANDLED;
 }
 
-static void analogix_dp_commit(struct analogix_dp_device *dp)
+static int analogix_dp_commit(struct analogix_dp_device *dp)
 {
 	int ret;
 
@@ -928,11 +933,10 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
 			DRM_ERROR("failed to disable the panel\n");
 	}
 
-	ret = readx_poll_timeout(analogix_dp_train_link, dp, ret, !ret, 100,
-				 DP_TIMEOUT_TRAINING_US * 5);
+	ret = analogix_dp_train_link(dp);
 	if (ret) {
 		dev_err(dp->dev, "unable to do link train, ret=%d\n", ret);
-		return;
+		return ret;
 	}
 
 	analogix_dp_enable_scramble(dp, 1);
@@ -953,6 +957,7 @@ static void analogix_dp_commit(struct analogix_dp_device *dp)
 	dp->psr_enable = analogix_dp_detect_sink_psr(dp);
 	if (dp->psr_enable)
 		analogix_dp_enable_sink_psr(dp);
+	return 0;
 }
 
 /*
@@ -1149,12 +1154,9 @@ static void analogix_dp_bridge_pre_enable(struct drm_bridge *bridge)
 		DRM_ERROR("failed to setup the panel ret = %d\n", ret);
 }
 
-static void analogix_dp_bridge_enable(struct drm_bridge *bridge)
+static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 {
-	struct analogix_dp_device *dp = bridge->driver_private;
-
-	if (dp->dpms_mode == DRM_MODE_DPMS_ON)
-		return;
+	int ret;
 
 	pm_runtime_get_sync(dp->dev);
 
@@ -1162,11 +1164,46 @@ static void analogix_dp_bridge_enable(struct drm_bridge *bridge)
 		dp->plat_data->power_on(dp->plat_data);
 
 	phy_power_on(dp->phy);
-	analogix_dp_init_dp(dp);
+
+	ret = analogix_dp_init_dp(dp);
+	if (ret)
+		goto out_dp_init;
+
+	ret = analogix_dp_commit(dp);
+	if (ret)
+		goto out_dp_init;
+
 	enable_irq(dp->irq);
-	analogix_dp_commit(dp);
+	return 0;
 
-	dp->dpms_mode = DRM_MODE_DPMS_ON;
+out_dp_init:
+	phy_power_off(dp->phy);
+	if (dp->plat_data->power_off)
+		dp->plat_data->power_off(dp->plat_data);
+	pm_runtime_put_sync(dp->dev);
+
+	return ret;
+}
+
+static void analogix_dp_bridge_enable(struct drm_bridge *bridge)
+{
+	struct analogix_dp_device *dp = bridge->driver_private;
+	int timeout_loop = 0;
+
+	if (dp->dpms_mode == DRM_MODE_DPMS_ON)
+		return;
+
+	while (timeout_loop < MAX_PLL_LOCK_LOOP) {
+		if (analogix_dp_set_bridge(dp) == 0) {
+			dp->dpms_mode = DRM_MODE_DPMS_ON;
+			return;
+		}
+		dev_err(dp->dev, "failed to set bridge, retry: %d\n",
+			timeout_loop);
+		timeout_loop++;
+		usleep_range(10, 11);
+	}
+	dev_err(dp->dev, "too many times retry set bridge, give it up\n");
 }
 
 static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
index 403ff853464b..769255dc6e99 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
@@ -19,6 +19,7 @@
 #define DP_TIMEOUT_LOOP_COUNT 100
 #define MAX_CR_LOOP 5
 #define MAX_EQ_LOOP 5
+#define MAX_PLL_LOCK_LOOP 5
 
 /* Training takes 22ms if AUX channel comm fails. Use this as retry interval */
 #define DP_TIMEOUT_TRAINING_US			22000
@@ -197,7 +198,7 @@ void analogix_dp_set_pll_power_down(struct analogix_dp_device *dp, bool enable);
 void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
 				       enum analog_power_block block,
 				       bool enable);
-void analogix_dp_init_analog_func(struct analogix_dp_device *dp);
+int analogix_dp_init_analog_func(struct analogix_dp_device *dp);
 void analogix_dp_init_hpd(struct analogix_dp_device *dp);
 void analogix_dp_force_hpd(struct analogix_dp_device *dp);
 enum dp_irq_type analogix_dp_get_irq_type(struct analogix_dp_device *dp);
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index e78c861b9e06..b47c5af43560 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -333,7 +333,7 @@ void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
 	}
 }
 
-void analogix_dp_init_analog_func(struct analogix_dp_device *dp)
+int analogix_dp_init_analog_func(struct analogix_dp_device *dp)
 {
 	u32 reg;
 	int timeout_loop = 0;
@@ -355,7 +355,7 @@ void analogix_dp_init_analog_func(struct analogix_dp_device *dp)
 			timeout_loop++;
 			if (DP_TIMEOUT_LOOP_COUNT < timeout_loop) {
 				dev_err(dp->dev, "failed to get pll lock status\n");
-				return;
+				return -ETIMEDOUT;
 			}
 			usleep_range(10, 20);
 		}
@@ -366,6 +366,7 @@ void analogix_dp_init_analog_func(struct analogix_dp_device *dp)
 	reg &= ~(SERDES_FIFO_FUNC_EN_N | LS_CLK_DOMAIN_FUNC_EN_N
 		| AUX_FUNC_EN_N);
 	writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_2);
+	return 0;
 }
 
 void analogix_dp_clear_hotplug_interrupts(struct analogix_dp_device *dp)
-- 
2.16.1

[PATCH v4 13/38] drm/bridge: analogix_dp: Wait for HPD signal before configuring link

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

According to DP spec v1.3 chap 3.5.1.2 Link Training, Link Policy Maker
must first detect that the HPD signal is asserted high by the Downstream
Device before establishing a link with it.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index c81733b8185e..92fb9a072cb6 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -1169,6 +1169,17 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 	if (ret)
 		goto out_dp_init;
 
+	/*
+	 * According to DP spec v1.3 chap 3.5.1.2 Link Training,
+	 * We should first make sure the HPD signal is asserted high by device
+	 * when we want to establish a link with it.
+	 */
+	ret = analogix_dp_detect_hpd(dp);
+	if (ret) {
+		DRM_ERROR("failed to get hpd single ret = %d\n", ret);
+		goto out_dp_init;
+	}
+
 	ret = analogix_dp_commit(dp);
 	if (ret)
 		goto out_dp_init;
-- 
2.16.1

[PATCH v4 14/38] drm/bridge: analogix_dp: Set PD_INC_BG first when powering up edp phy

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 10 ++++++++--
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h |  3 +++
 2 files changed, 11 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index b47c5af43560..bb72f8b0e603 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -321,10 +321,16 @@ void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
 		break;
 	case POWER_ALL:
 		if (enable) {
-			reg = DP_PHY_PD | AUX_PD | CH3_PD | CH2_PD |
-				CH1_PD | CH0_PD;
+			reg = DP_ALL_PD;
 			writel(reg, dp->reg_base + phy_pd_addr);
 		} else {
+			reg = DP_ALL_PD;
+			writel(reg, dp->reg_base + phy_pd_addr);
+			usleep_range(10, 15);
+			reg &= ~DP_INC_BG;
+			writel(reg, dp->reg_base + phy_pd_addr);
+			usleep_range(10, 15);
+
 			writel(0x00, dp->reg_base + phy_pd_addr);
 		}
 		break;
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
index 40200c652533..9602668669f4 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
@@ -342,12 +342,15 @@
 #define DP_PLL_REF_BIT_1_2500V			(0x7 << 0)
 
 /* ANALOGIX_DP_PHY_PD */
+#define DP_INC_BG				(0x1 << 7)
+#define DP_EXP_BG				(0x1 << 6)
 #define DP_PHY_PD				(0x1 << 5)
 #define AUX_PD					(0x1 << 4)
 #define CH3_PD					(0x1 << 3)
 #define CH2_PD					(0x1 << 2)
 #define CH1_PD					(0x1 << 1)
 #define CH0_PD					(0x1 << 0)
+#define DP_ALL_PD				(0xff)
 
 /* ANALOGIX_DP_PHY_TEST */
 #define MACRO_RST				(0x1 << 5)
-- 
2.16.1

[PATCH v4 15/38] drm/bridge: analogix_dp: Ensure edp is disabled when shutting down the panel

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

When panel is shut down, we should make sure edp can be disabled to avoid
undefined behavior.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 92fb9a072cb6..9b7d530ad24c 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -1160,6 +1160,12 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 
 	pm_runtime_get_sync(dp->dev);
 
+	ret = clk_prepare_enable(dp->clock);
+	if (ret < 0) {
+		DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret);
+		goto out_dp_clk_pre;
+	}
+
 	if (dp->plat_data->power_on)
 		dp->plat_data->power_on(dp->plat_data);
 
@@ -1191,6 +1197,8 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 	phy_power_off(dp->phy);
 	if (dp->plat_data->power_off)
 		dp->plat_data->power_off(dp->plat_data);
+	clk_disable_unprepare(dp->clock);
+out_dp_clk_pre:
 	pm_runtime_put_sync(dp->dev);
 
 	return ret;
@@ -1234,10 +1242,13 @@ static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
 
 	disable_irq(dp->irq);
 	phy_power_off(dp->phy);
+	analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);
 
 	if (dp->plat_data->power_off)
 		dp->plat_data->power_off(dp->plat_data);
 
+	clk_disable_unprepare(dp->clock);
+
 	pm_runtime_put_sync(dp->dev);
 
 	ret = analogix_dp_prepare_panel(dp, false, true);
-- 
2.16.1

[PATCH v4 16/38] drm/bridge: analogix_dp: Extend hpd check time to 100ms

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

There was a 1ms delay to detect the hpd signal, which is too short to
detect a short pulse. This patch extends this delay to 100ms.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 9b7d530ad24c..0ff151f741a3 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -76,7 +76,7 @@ static int analogix_dp_detect_hpd(struct analogix_dp_device *dp)
 			return 0;
 
 		timeout_loop++;
-		usleep_range(10, 11);
+		usleep_range(1000, 1100);
 	}
 
 	/*
-- 
2.16.1

[PATCH v4 17/38] drm/bridge: analogix_dp: Fix incorrect usage of enhanced mode

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

Enhanced mode is required by the eDP 1.2 specification, and not doing it
early could result in a period of time where we have a link transmitting
idle packets without it. Since there is no reason to disable it, we just
enable it at the beginning of link training and then keep it on all the
time.

Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 0ff151f741a3..5489570ef010 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -281,6 +281,8 @@ static int analogix_dp_link_start(struct analogix_dp_device *dp)
 	retval = drm_dp_dpcd_write(&dp->aux, DP_LINK_BW_SET, buf, 2);
 	if (retval < 0)
 		return retval;
+	/* set enhanced mode if available */
+	analogix_dp_set_enhanced_mode(dp);
 
 	/* Set TX pre-emphasis to minimum */
 	for (lane = 0; lane < lane_count; lane++)
@@ -593,8 +595,6 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 		dev_dbg(dp->dev, "fast link training %s\n",
 			dp->fast_train_enable ? "supported" : "unsupported");
 
-		/* set enhanced mode if available */
-		analogix_dp_set_enhanced_mode(dp);
 		dp->link_train.lt_state = FINISHED;
 
 		return 0;
@@ -940,8 +940,6 @@ static int analogix_dp_commit(struct analogix_dp_device *dp)
 	}
 
 	analogix_dp_enable_scramble(dp, 1);
-	analogix_dp_enable_rx_to_enhanced_mode(dp, 1);
-	analogix_dp_enable_enhanced_mode(dp, 1);
 
 	analogix_dp_init_video(dp);
 	ret = analogix_dp_config_video(dp);
-- 
2.16.1

[PATCH v4 18/38] drm/bridge: analogix_dp: Check dpcd write/read status

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

We need to check the dpcd write/read return value to see whether the
write/read was successful

Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 169 ++++++++++++++++-----
 1 file changed, 127 insertions(+), 42 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 5489570ef010..2d49ee6fd2f3 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -160,80 +160,137 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
 }
 EXPORT_SYMBOL_GPL(analogix_dp_disable_psr);
 
-static bool analogix_dp_detect_sink_psr(struct analogix_dp_device *dp)
+static int analogix_dp_detect_sink_psr(struct analogix_dp_device *dp)
 {
 	unsigned char psr_version;
+	int ret;
+
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_SUPPORT, &psr_version);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to get PSR version, disable it\n");
+		return ret;
+	}
 
-	drm_dp_dpcd_readb(&dp->aux, DP_PSR_SUPPORT, &psr_version);
 	dev_dbg(dp->dev, "Panel PSR version : %x\n", psr_version);
 
-	return (psr_version & DP_PSR_IS_SUPPORTED) ? true : false;
+	dp->psr_enable = (psr_version & DP_PSR_IS_SUPPORTED) ? true : false;
+
+	return 0;
 }
 
-static void analogix_dp_enable_sink_psr(struct analogix_dp_device *dp)
+static int analogix_dp_enable_sink_psr(struct analogix_dp_device *dp)
 {
 	unsigned char psr_en;
+	int ret;
 
 	/* Disable psr function */
-	drm_dp_dpcd_readb(&dp->aux, DP_PSR_EN_CFG, &psr_en);
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_PSR_EN_CFG, &psr_en);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to get psr config\n");
+		goto end;
+	}
+
 	psr_en &= ~DP_PSR_ENABLE;
-	drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to disable panel psr\n");
+		goto end;
+	}
 
 	/* Main-Link transmitter remains active during PSR active states */
 	psr_en = DP_PSR_MAIN_LINK_ACTIVE | DP_PSR_CRC_VERIFICATION;
-	drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to set panel psr\n");
+		goto end;
+	}
 
 	/* Enable psr function */
 	psr_en = DP_PSR_ENABLE | DP_PSR_MAIN_LINK_ACTIVE |
 		 DP_PSR_CRC_VERIFICATION;
-	drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_PSR_EN_CFG, psr_en);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to set panel psr\n");
+		goto end;
+	}
 
 	analogix_dp_enable_psr_crc(dp);
+
+	return 0;
+end:
+	dev_err(dp->dev, "enable psr fail, force to disable psr\n");
+	dp->psr_enable = false;
+
+	return ret;
 }
 
-static void
+static int
 analogix_dp_enable_rx_to_enhanced_mode(struct analogix_dp_device *dp,
 				       bool enable)
 {
 	u8 data;
+	int ret;
 
-	drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_LANE_COUNT_SET, &data);
+	if (ret != 1)
+		return ret;
 
 	if (enable)
-		drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
-				   DP_LANE_COUNT_ENHANCED_FRAME_EN |
-					DPCD_LANE_COUNT_SET(data));
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
+					 DP_LANE_COUNT_ENHANCED_FRAME_EN |
+					 DPCD_LANE_COUNT_SET(data));
 	else
-		drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
-				   DPCD_LANE_COUNT_SET(data));
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_LANE_COUNT_SET,
+					 DPCD_LANE_COUNT_SET(data));
+
+	return ret < 0 ? ret : 0;
 }
 
-static int analogix_dp_is_enhanced_mode_available(struct analogix_dp_device *dp)
+static int analogix_dp_is_enhanced_mode_available(struct analogix_dp_device *dp,
+						  u8 *enhanced_mode_support)
 {
 	u8 data;
-	int retval;
+	int ret;
 
-	drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data);
-	retval = DPCD_ENHANCED_FRAME_CAP(data);
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_LANE_COUNT, &data);
+	if (ret != 1) {
+		*enhanced_mode_support = 0;
+		return ret;
+	}
 
-	return retval;
+	*enhanced_mode_support = DPCD_ENHANCED_FRAME_CAP(data);
+
+	return 0;
 }
 
-static void analogix_dp_set_enhanced_mode(struct analogix_dp_device *dp)
+static int analogix_dp_set_enhanced_mode(struct analogix_dp_device *dp)
 {
 	u8 data;
+	int ret;
+
+	ret = analogix_dp_is_enhanced_mode_available(dp, &data);
+	if (ret < 0)
+		return ret;
+
+	ret = analogix_dp_enable_rx_to_enhanced_mode(dp, data);
+	if (ret < 0)
+		return ret;
 
-	data = analogix_dp_is_enhanced_mode_available(dp);
-	analogix_dp_enable_rx_to_enhanced_mode(dp, data);
 	analogix_dp_enable_enhanced_mode(dp, data);
+
+	return 0;
 }
 
-static void analogix_dp_training_pattern_dis(struct analogix_dp_device *dp)
+static int analogix_dp_training_pattern_dis(struct analogix_dp_device *dp)
 {
+	int ret;
+
 	analogix_dp_set_training_pattern(dp, DP_NONE);
 
-	drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
-			   DP_TRAINING_PATTERN_DISABLE);
+	ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+				 DP_TRAINING_PATTERN_DISABLE);
+
+	return ret < 0 ? ret : 0;
 }
 
 static void
@@ -282,7 +339,11 @@ static int analogix_dp_link_start(struct analogix_dp_device *dp)
 	if (retval < 0)
 		return retval;
 	/* set enhanced mode if available */
-	analogix_dp_set_enhanced_mode(dp);
+	retval = analogix_dp_set_enhanced_mode(dp);
+	if (retval < 0) {
+		dev_err(dp->dev, "failed to set enhance mode\n");
+		return retval;
+	}
 
 	/* Set TX pre-emphasis to minimum */
 	for (lane = 0; lane < lane_count; lane++)
@@ -567,10 +628,11 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 
 	if (!analogix_dp_channel_eq_ok(link_status, link_align, lane_count)) {
 		/* traing pattern Set to Normal */
-		analogix_dp_training_pattern_dis(dp);
+		retval = analogix_dp_training_pattern_dis(dp);
+		if (retval < 0)
+			return retval;
 
 		dev_info(dp->dev, "Link Training success!\n");
-
 		analogix_dp_get_link_bandwidth(dp, &reg);
 		dp->link_train.link_rate = reg;
 		dev_dbg(dp->dev, "final bandwidth = %.2x\n",
@@ -867,24 +929,32 @@ static int analogix_dp_config_video(struct analogix_dp_device *dp)
 	return 0;
 }
 
-static void analogix_dp_enable_scramble(struct analogix_dp_device *dp,
-					bool enable)
+static int analogix_dp_enable_scramble(struct analogix_dp_device *dp,
+				       bool enable)
 {
 	u8 data;
+	int ret;
 
 	if (enable) {
 		analogix_dp_enable_scrambling(dp);
 
-		drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET, &data);
-		drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+		ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET,
+					&data);
+		if (ret != 1)
+			return ret;
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
 				   (u8)(data & ~DP_LINK_SCRAMBLING_DISABLE));
 	} else {
 		analogix_dp_disable_scrambling(dp);
 
-		drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET, &data);
-		drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
+		ret = drm_dp_dpcd_readb(&dp->aux, DP_TRAINING_PATTERN_SET,
+					&data);
+		if (ret != 1)
+			return ret;
+		ret = drm_dp_dpcd_writeb(&dp->aux, DP_TRAINING_PATTERN_SET,
 				   (u8)(data | DP_LINK_SCRAMBLING_DISABLE));
 	}
+	return ret < 0 ? ret : 0;
 }
 
 static irqreturn_t analogix_dp_hardirq(int irq, void *arg)
@@ -939,23 +1009,36 @@ static int analogix_dp_commit(struct analogix_dp_device *dp)
 		return ret;
 	}
 
-	analogix_dp_enable_scramble(dp, 1);
+	ret = analogix_dp_enable_scramble(dp, 1);
+	if (ret < 0) {
+		dev_err(dp->dev, "can not enable scramble\n");
+		return ret;
+	}
 
 	analogix_dp_init_video(dp);
 	ret = analogix_dp_config_video(dp);
-	if (ret)
+	if (ret) {
 		dev_err(dp->dev, "unable to config video\n");
+		return ret;
+	}
 
 	/* Safe to enable the panel now */
 	if (dp->plat_data->panel) {
-		if (drm_panel_enable(dp->plat_data->panel))
+		ret = drm_panel_enable(dp->plat_data->panel);
+		if (ret) {
 			DRM_ERROR("failed to enable the panel\n");
+			return ret;
+		}
 	}
 
-	dp->psr_enable = analogix_dp_detect_sink_psr(dp);
+	ret = analogix_dp_detect_sink_psr(dp);
+	if (ret)
+		return ret;
+
 	if (dp->psr_enable)
-		analogix_dp_enable_sink_psr(dp);
-	return 0;
+		ret = analogix_dp_enable_sink_psr(dp);
+
+	return ret;
 }
 
 /*
@@ -1185,8 +1268,10 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 	}
 
 	ret = analogix_dp_commit(dp);
-	if (ret)
+	if (ret) {
+		DRM_ERROR("dp commit error, ret = %d\n", ret);
 		goto out_dp_init;
+	}
 
 	enable_irq(dp->irq);
 	return 0;
-- 
2.16.1

[PATCH v4 19/38] drm/bridge: analogix_dp: Fix AUX_PD bit for Rockchip

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 117 ++++++++++++----------
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h |   2 +
 2 files changed, 65 insertions(+), 54 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index bb72f8b0e603..dee1ba109b5f 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -248,76 +248,85 @@ void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
 {
 	u32 reg;
 	u32 phy_pd_addr = ANALOGIX_DP_PHY_PD;
+	u32 mask;
 
 	if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
 		phy_pd_addr = ANALOGIX_DP_PD;
 
 	switch (block) {
 	case AUX_BLOCK:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= AUX_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~AUX_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
+			mask = RK_AUX_PD;
+		else
+			mask = AUX_PD;
+
+		reg = readl(dp->reg_base + phy_pd_addr);
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+		writel(reg, dp->reg_base + phy_pd_addr);
 		break;
 	case CH0_BLOCK:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= CH0_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~CH0_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		mask = CH0_PD;
+		reg = readl(dp->reg_base + phy_pd_addr);
+
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+		writel(reg, dp->reg_base + phy_pd_addr);
 		break;
 	case CH1_BLOCK:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= CH1_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~CH1_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		mask = CH1_PD;
+		reg = readl(dp->reg_base + phy_pd_addr);
+
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+		writel(reg, dp->reg_base + phy_pd_addr);
 		break;
 	case CH2_BLOCK:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= CH2_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~CH2_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		mask = CH2_PD;
+		reg = readl(dp->reg_base + phy_pd_addr);
+
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+		writel(reg, dp->reg_base + phy_pd_addr);
 		break;
 	case CH3_BLOCK:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= CH3_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~CH3_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		mask = CH3_PD;
+		reg = readl(dp->reg_base + phy_pd_addr);
+
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+		writel(reg, dp->reg_base + phy_pd_addr);
 		break;
 	case ANALOG_TOTAL:
-		if (enable) {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg |= DP_PHY_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		} else {
-			reg = readl(dp->reg_base + phy_pd_addr);
-			reg &= ~DP_PHY_PD;
-			writel(reg, dp->reg_base + phy_pd_addr);
-		}
+		/*
+		 * There is no bit named DP_PHY_PD, so We used DP_INC_BG
+		 * to power off everything instead of DP_PHY_PD in
+		 * Rockchip
+		 */
+		if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
+			mask = DP_INC_BG;
+		else
+			mask = DP_PHY_PD;
+
+		reg = readl(dp->reg_base + phy_pd_addr);
+		if (enable)
+			reg |= mask;
+		else
+			reg &= ~mask;
+
+		writel(reg, dp->reg_base + phy_pd_addr);
+		if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
+			usleep_range(10, 15);
 		break;
 	case POWER_ALL:
 		if (enable) {
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
index 9602668669f4..b633a4a5082a 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
@@ -345,7 +345,9 @@
 #define DP_INC_BG				(0x1 << 7)
 #define DP_EXP_BG				(0x1 << 6)
 #define DP_PHY_PD				(0x1 << 5)
+#define RK_AUX_PD				(0x1 << 5)
 #define AUX_PD					(0x1 << 4)
+#define RK_PLL_PD				(0x1 << 4)
 #define CH3_PD					(0x1 << 3)
 #define CH2_PD					(0x1 << 2)
 #define CH1_PD					(0x1 << 1)
-- 
2.16.1

[PATCH v4 20/38] drm/bridge: analogix_dp: Reset aux channel if an error occurred

[Enric Balletbo i Serra]

From: Lin Huang <hl@rock-chips.com>

AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel if some
errors occurred.

Cc: 征增 王 <wzz@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 18 ++++++++++++++----
 1 file changed, 14 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index dee1ba109b5f..7b7fd227e1f9 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -466,6 +466,10 @@ void analogix_dp_init_aux(struct analogix_dp_device *dp)
 	reg = RPLY_RECEIV | AUX_ERR;
 	writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA);
 
+	analogix_dp_set_analog_power_down(dp, AUX_BLOCK, true);
+	usleep_range(10, 11);
+	analogix_dp_set_analog_power_down(dp, AUX_BLOCK, false);
+
 	analogix_dp_reset_aux(dp);
 
 	/* Disable AUX transaction H/W retry */
@@ -1159,7 +1163,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 				 reg, !(reg & AUX_EN), 25, 500 * 1000);
 	if (ret) {
 		dev_err(dp->dev, "AUX CH enable timeout!\n");
-		return -ETIMEDOUT;
+		goto aux_error;
 	}
 
 	/* TODO: Wait for an interrupt instead of looping? */
@@ -1168,7 +1172,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 				 reg, reg & RPLY_RECEIV, 10, 20 * 1000);
 	if (ret) {
 		dev_err(dp->dev, "AUX CH cmd reply timeout!\n");
-		return -ETIMEDOUT;
+		goto aux_error;
 	}
 
 	/* Clear interrupt source for AUX CH command reply */
@@ -1178,7 +1182,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 	reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA);
 	if (reg & AUX_ERR) {
 		writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA);
-		return -EREMOTEIO;
+		goto aux_error;
 	}
 
 	/* Check AUX CH error access status */
@@ -1186,7 +1190,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 	if ((reg & AUX_STATUS_MASK)) {
 		dev_err(dp->dev, "AUX CH error happened: %d\n\n",
 			reg & AUX_STATUS_MASK);
-		return -EREMOTEIO;
+		goto aux_error;
 	}
 
 	if (msg->request & DP_AUX_I2C_READ) {
@@ -1212,4 +1216,10 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 		msg->reply = DP_AUX_NATIVE_REPLY_ACK;
 
 	return num_transferred > 0 ? num_transferred : -EBUSY;
+
+aux_error:
+	/* if aux err happen, reset aux */
+	analogix_dp_init_aux(dp);
+
+	return -EREMOTEIO;
 }
-- 
2.16.1

[PATCH v4 21/38] drm/rockchip: Restore psr->state when enable/disable psr failed

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

If we failed disable psr, it would hang the display until next psr
cycle coming. So we should restore psr->state when it failed.

Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c |  4 +++-
 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    | 10 +++++-----
 drivers/gpu/drm/rockchip/rockchip_drm_psr.c        | 20 +++++++++++++-------
 drivers/gpu/drm/rockchip/rockchip_drm_psr.h        |  2 +-
 4 files changed, 22 insertions(+), 14 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 2d49ee6fd2f3..c93a0d125b87 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -153,8 +153,10 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
 	psr_vsc.DB1 = 0;
 
 	ret = drm_dp_dpcd_writeb(&dp->aux, DP_SET_POWER, DP_SET_POWER_D0);
-	if (ret != 1)
+	if (ret != 1) {
 		dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret);
+		return ret;
+	}
 
 	return analogix_dp_send_psr_spd(dp, &psr_vsc, false);
 }
diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index 3e8bf79bea58..8c884f9ce713 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -77,13 +77,13 @@ struct rockchip_dp_device {
 	struct analogix_dp_plat_data plat_data;
 };
 
-static void analogix_dp_psr_set(struct drm_encoder *encoder, bool enabled)
+static int analogix_dp_psr_set(struct drm_encoder *encoder, bool enabled)
 {
 	struct rockchip_dp_device *dp = to_dp(encoder);
 	int ret;
 
 	if (!analogix_dp_psr_enabled(dp->adp))
-		return;
+		return 0;
 
 	DRM_DEV_DEBUG(dp->dev, "%s PSR...\n", enabled ? "Entry" : "Exit");
 
@@ -91,13 +91,13 @@ static void analogix_dp_psr_set(struct drm_encoder *encoder, bool enabled)
 					 PSR_WAIT_LINE_FLAG_TIMEOUT_MS);
 	if (ret) {
 		DRM_DEV_ERROR(dp->dev, "line flag interrupt did not arrive\n");
-		return;
+		return -ETIMEDOUT;
 	}
 
 	if (enabled)
-		analogix_dp_enable_psr(dp->adp);
+		return analogix_dp_enable_psr(dp->adp);
 	else
-		analogix_dp_disable_psr(dp->adp);
+		return analogix_dp_disable_psr(dp->adp);
 }
 
 static int rockchip_dp_pre_init(struct rockchip_dp_device *dp)
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
index b339ca943139..9376f4396b6b 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
@@ -36,7 +36,7 @@ struct psr_drv {
 
 	struct delayed_work	flush_work;
 
-	void (*set)(struct drm_encoder *encoder, bool enable);
+	int (*set)(struct drm_encoder *encoder, bool enable);
 };
 
 static struct psr_drv *find_psr_by_crtc(struct drm_crtc *crtc)
@@ -93,19 +93,25 @@ static void psr_set_state_locked(struct psr_drv *psr, enum psr_state state)
 		return;
 	}
 
-	psr->state = state;
-
 	/* Actually commit the state change to hardware */
-	switch (psr->state) {
+	switch (state) {
 	case PSR_ENABLE:
-		psr->set(psr->encoder, true);
+		if (psr->set(psr->encoder, true))
+			return;
 		break;
 
 	case PSR_DISABLE:
 	case PSR_FLUSH:
-		psr->set(psr->encoder, false);
+		if (psr->set(psr->encoder, false))
+			return;
 		break;
+
+	default:
+		pr_err("%s: Unknown state %d\n", __func__, state);
+		return;
 	}
+
+	psr->state = state;
 }
 
 static void psr_set_state(struct psr_drv *psr, enum psr_state state)
@@ -229,7 +235,7 @@ EXPORT_SYMBOL(rockchip_drm_psr_flush_all);
  * Zero on success, negative errno on failure.
  */
 int rockchip_drm_psr_register(struct drm_encoder *encoder,
-			void (*psr_set)(struct drm_encoder *, bool enable))
+			int (*psr_set)(struct drm_encoder *, bool enable))
 {
 	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
 	struct psr_drv *psr;
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.h b/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
index b1ea0155e57c..06537ee27565 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.h
@@ -22,7 +22,7 @@ int rockchip_drm_psr_activate(struct drm_encoder *encoder);
 int rockchip_drm_psr_deactivate(struct drm_encoder *encoder);
 
 int rockchip_drm_psr_register(struct drm_encoder *encoder,
-			void (*psr_set)(struct drm_encoder *, bool enable));
+			int (*psr_set)(struct drm_encoder *, bool enable));
 void rockchip_drm_psr_unregister(struct drm_encoder *encoder);
 
 #endif /* __ROCKCHIP_DRM_PSR__ */
-- 
2.16.1

[PATCH v4 22/38] drm/bridge: analogix_dp: Don't use ANALOGIX_DP_PLL_CTL to control pll

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list.  We should use BIT_4 in ANALOGIX_DP_PD to control the pll power
instead of ANALOGIX_DP_PLL_CTL.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 20 ++++++++++++--------
 1 file changed, 12 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 7b7fd227e1f9..02ab1aaa9993 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -230,16 +230,20 @@ enum pll_status analogix_dp_get_pll_lock_status(struct analogix_dp_device *dp)
 void analogix_dp_set_pll_power_down(struct analogix_dp_device *dp, bool enable)
 {
 	u32 reg;
+	u32 mask = DP_PLL_PD;
+	u32 pd_addr = ANALOGIX_DP_PLL_CTL;
 
-	if (enable) {
-		reg = readl(dp->reg_base + ANALOGIX_DP_PLL_CTL);
-		reg |= DP_PLL_PD;
-		writel(reg, dp->reg_base + ANALOGIX_DP_PLL_CTL);
-	} else {
-		reg = readl(dp->reg_base + ANALOGIX_DP_PLL_CTL);
-		reg &= ~DP_PLL_PD;
-		writel(reg, dp->reg_base + ANALOGIX_DP_PLL_CTL);
+	if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) {
+		pd_addr = ANALOGIX_DP_PD;
+		mask = RK_PLL_PD;
 	}
+
+	reg = readl(dp->reg_base + pd_addr);
+	if (enable)
+		reg |= mask;
+	else
+		reg &= ~mask;
+	writel(reg, dp->reg_base + pd_addr);
 }
 
 void analogix_dp_set_analog_power_down(struct analogix_dp_device *dp,
-- 
2.16.1

[PATCH v4 23/38] drm/bridge: analogix_dp: Fix timeout of video streamclk config

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

The STRM_VALID bit in register ANALOGIX_DP_SYS_CTL_3 may be unstable,
so we may hit the error log "Timeout of video streamclk ok" since
checked this unstable bit.
In fact, we can go continue and the streamclk is ok if we wait enough time,
it does no effect on display.
Let's change this error to warn.

Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index c93a0d125b87..2493a580e655 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -921,8 +921,9 @@ static int analogix_dp_config_video(struct analogix_dp_device *dp)
 			done_count = 0;
 		}
 		if (timeout_loop > DP_TIMEOUT_LOOP_COUNT) {
-			dev_err(dp->dev, "Timeout of video streamclk ok\n");
-			return -ETIMEDOUT;
+			dev_warn(dp->dev,
+				 "Ignoring timeout of video streamclk ok\n");
+			break;
 		}
 
 		usleep_range(1000, 1001);
-- 
2.16.1

[PATCH v4 24/38] drm/bridge: analogix_dp: Fix incorrect operations with register ANALOGIX_DP_FUNC_EN_1

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:

on Exynos edp phy,
BIT 7		MASTER_VID_FUNC_EN_N
BIT 6		reserved
BIT 5		SLAVE_VID_FUNC_EN_N

on Rockchip edp phy,
BIT 7		reserved
BIT 6		RK_VID_CAP_FUNC_EN_N
BIT 5		RK_VID_FIFO_FUNC_EN_N

So, we should do some private operations to Rockchip.

Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 19 ++++++++++++++-----
 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h |  2 ++
 2 files changed, 16 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 02ab1aaa9993..4eae206ec31b 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -126,9 +126,14 @@ void analogix_dp_reset(struct analogix_dp_device *dp)
 	analogix_dp_stop_video(dp);
 	analogix_dp_enable_video_mute(dp, 0);
 
-	reg = MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N |
-		AUD_FIFO_FUNC_EN_N | AUD_FUNC_EN_N |
-		HDCP_FUNC_EN_N | SW_FUNC_EN_N;
+	if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
+		reg = RK_VID_CAP_FUNC_EN_N | RK_VID_FIFO_FUNC_EN_N |
+			SW_FUNC_EN_N;
+	else
+		reg = MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N |
+			AUD_FIFO_FUNC_EN_N | AUD_FUNC_EN_N |
+			HDCP_FUNC_EN_N | SW_FUNC_EN_N;
+
 	writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_1);
 
 	reg = SSC_FUNC_EN_N | AUX_FUNC_EN_N |
@@ -971,8 +976,12 @@ void analogix_dp_config_video_slave_mode(struct analogix_dp_device *dp)
 	u32 reg;
 
 	reg = readl(dp->reg_base + ANALOGIX_DP_FUNC_EN_1);
-	reg &= ~(MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N);
-	reg |= MASTER_VID_FUNC_EN_N;
+	if (dp->plat_data && is_rockchip(dp->plat_data->dev_type)) {
+		reg &= ~(RK_VID_CAP_FUNC_EN_N | RK_VID_FIFO_FUNC_EN_N);
+	} else {
+		reg &= ~(MASTER_VID_FUNC_EN_N | SLAVE_VID_FUNC_EN_N);
+		reg |= MASTER_VID_FUNC_EN_N;
+	}
 	writel(reg, dp->reg_base + ANALOGIX_DP_FUNC_EN_1);
 
 	reg = readl(dp->reg_base + ANALOGIX_DP_VIDEO_CTL_10);
diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
index b633a4a5082a..0cf27c731727 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h
@@ -127,7 +127,9 @@
 
 /* ANALOGIX_DP_FUNC_EN_1 */
 #define MASTER_VID_FUNC_EN_N			(0x1 << 7)
+#define RK_VID_CAP_FUNC_EN_N			(0x1 << 6)
 #define SLAVE_VID_FUNC_EN_N			(0x1 << 5)
+#define RK_VID_FIFO_FUNC_EN_N			(0x1 << 5)
 #define AUD_FIFO_FUNC_EN_N			(0x1 << 4)
 #define AUD_FUNC_EN_N				(0x1 << 3)
 #define HDCP_FUNC_EN_N				(0x1 << 2)
-- 
2.16.1

[PATCH v4 25/38] drm/bridge: analogix_dp: Move fast link training detect to set_bridge

[Enric Balletbo i Serra]

From: zain wang <wzz@rock-chips.com>

It's too early to detect fast link training, if other step after it
failed, we will set fast_link flag to 1, and retry set_bridge again. In
this case we will power down and power up panel power supply, and we
will do fast link training since we have set fast_link flag to 1. In
fact, we should do full link training now, not the fast link training.
So we should move the fast link detection at the end of set_bridge.

Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 42 +++++++++++++---------
 1 file changed, 26 insertions(+), 16 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index 2493a580e655..e0f96ad4c700 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -601,7 +601,7 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 {
 	int lane, lane_count, retval;
 	u32 reg;
-	u8 link_align, link_status[2], adjust_request[2], spread;
+	u8 link_align, link_status[2], adjust_request[2];
 
 	usleep_range(400, 401);
 
@@ -645,20 +645,6 @@ static int analogix_dp_process_equalizer_training(struct analogix_dp_device *dp)
 		dev_dbg(dp->dev, "final lane count = %.2x\n",
 			dp->link_train.lane_count);
 
-		retval = drm_dp_dpcd_readb(&dp->aux, DP_MAX_DOWNSPREAD,
-					   &spread);
-		if (retval != 1) {
-			dev_err(dp->dev, "failed to read downspread %d\n",
-				retval);
-			dp->fast_train_enable = false;
-		} else {
-			dp->fast_train_enable =
-				(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING) ?
-					true : false;
-		}
-		dev_dbg(dp->dev, "fast link training %s\n",
-			dp->fast_train_enable ? "supported" : "unsupported");
-
 		dp->link_train.lt_state = FINISHED;
 
 		return 0;
@@ -996,6 +982,22 @@ static irqreturn_t analogix_dp_irq_thread(int irq, void *arg)
 	return IRQ_HANDLED;
 }
 
+static int analogix_dp_fast_link_train_detection(struct analogix_dp_device *dp)
+{
+	int ret;
+	u8 spread;
+
+	ret = drm_dp_dpcd_readb(&dp->aux, DP_MAX_DOWNSPREAD, &spread);
+	if (ret != 1) {
+		dev_err(dp->dev, "failed to read downspread %d\n", ret);
+		return ret;
+	}
+	dp->fast_train_enable = !!(spread & DP_NO_AUX_HANDSHAKE_LINK_TRAINING);
+	dev_dbg(dp->dev, "fast link training %s\n",
+		dp->fast_train_enable ? "supported" : "unsupported");
+	return 0;
+}
+
 static int analogix_dp_commit(struct analogix_dp_device *dp)
 {
 	int ret;
@@ -1038,8 +1040,16 @@ static int analogix_dp_commit(struct analogix_dp_device *dp)
 	if (ret)
 		return ret;
 
-	if (dp->psr_enable)
+	if (dp->psr_enable) {
 		ret = analogix_dp_enable_sink_psr(dp);
+		if (ret)
+			return ret;
+	}
+
+	/* Check whether panel supports fast training */
+	ret =  analogix_dp_fast_link_train_detection(dp);
+	if (ret)
+		dp->psr_enable = false;
 
 	return ret;
 }
-- 
2.16.1

[PATCH v4 26/38] drm/bridge: analogix_dp: Reorder plat_data->power_off to happen sooner

[Enric Balletbo i Serra]

From: Douglas Anderson <dianders@chromium.org>

The current user of the analogix power_off is "analogix_dp-rockchip".
That driver does this:
- deactivate PSR
- turn off a clock

Both of these things (especially deactive PSR) should be done before
we turn the PHY power off and turn off analog power.  Let's move the
callback up.

Note that without this patch (and with
https://patchwork.kernel.org/patch/9553349/ [seanpaul: this patch was
not applied, but it seems like the race can still occur]), I experienced
an error in reboot testing where one thread was at:

  rockchip_drm_psr_deactivate
  rockchip_dp_powerdown
  analogix_dp_bridge_disable
  drm_bridge_disable

...and the other thread was at:

  analogix_dp_send_psr_spd
  analogix_dp_enable_psr
  analogix_dp_psr_set
  psr_flush_handler

The flush handler thread was finding AUX channel errors and eventually
reported "Failed to apply PSR", where I had a kgdb breakpoint. Presumably
the device would have eventually given up and shut down anyway, but it
seems better to fix the order to be more correct.

Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index e0f96ad4c700..edaca650e6d2 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -1337,12 +1337,13 @@ static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
 	}
 
 	disable_irq(dp->irq);
-	phy_power_off(dp->phy);
-	analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);
 
 	if (dp->plat_data->power_off)
 		dp->plat_data->power_off(dp->plat_data);
 
+	phy_power_off(dp->phy);
+	analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);
+
 	clk_disable_unprepare(dp->clock);
 
 	pm_runtime_put_sync(dp->dev);
-- 
2.16.1

[PATCH v4 27/38] drm/bridge: analogix_dp: Properly log AUX CH errors

[Enric Balletbo i Serra]

From: Douglas Anderson <dianders@chromium.org>

The code in analogix_dp_transfer() that was supposed to print out:
  AUX CH error happened

Was actually dead code. That's because the previous check (whether
the interrupt status indicated any errors) would have hit for all
errors anyway.

Let's combine the two error checks so we can actually see AUX CH
errors.  We'll also downgrade the message to a warning since some of
these types of errors might be expected for some displays.  If this
gets too noisy we can downgrade again to debug.

Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 4eae206ec31b..58e8a28e99aa 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -1105,6 +1105,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 			     struct drm_dp_aux_msg *msg)
 {
 	u32 reg;
+	u32 status_reg;
 	u8 *buffer = msg->buffer;
 	unsigned int i;
 	int num_transferred = 0;
@@ -1193,16 +1194,12 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
 
 	/* Clear interrupt source for AUX CH access error */
 	reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA);
-	if (reg & AUX_ERR) {
+	status_reg = readl(dp->reg_base + ANALOGIX_DP_AUX_CH_STA);
+	if ((reg & AUX_ERR) || (status_reg & AUX_STATUS_MASK)) {
 		writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA);
-		goto aux_error;
-	}
 
-	/* Check AUX CH error access status */
-	reg = readl(dp->reg_base + ANALOGIX_DP_AUX_CH_STA);
-	if ((reg & AUX_STATUS_MASK)) {
-		dev_err(dp->dev, "AUX CH error happened: %d\n\n",
-			reg & AUX_STATUS_MASK);
+		dev_warn(dp->dev, "AUX CH error happened: %#x (%d)\n",
+			 status_reg & AUX_STATUS_MASK, !!(reg & AUX_ERR));
 		goto aux_error;
 	}
 
-- 
2.16.1

[PATCH v4 28/38] drm/bridge: analogix_dp: Properly disable aux chan retries on rockchip

[Enric Balletbo i Serra]

From: Douglas Anderson <dianders@chromium.org>

The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it sets them to
3.  If we actually need 3 retries for Rockchip then we could adjust
the comment, but it seems more likely that we want the same retry
behavior across all platforms.

Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 15 ++++++++-------
 1 file changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
index 58e8a28e99aa..a5f2763d72e4 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
@@ -481,15 +481,16 @@ void analogix_dp_init_aux(struct analogix_dp_device *dp)
 
 	analogix_dp_reset_aux(dp);
 
-	/* Disable AUX transaction H/W retry */
+	/* AUX_BIT_PERIOD_EXPECTED_DELAY doesn't apply to Rockchip IP */
 	if (dp->plat_data && is_rockchip(dp->plat_data->dev_type))
-		reg = AUX_BIT_PERIOD_EXPECTED_DELAY(0) |
-		      AUX_HW_RETRY_COUNT_SEL(3) |
-		      AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
+		reg = 0;
 	else
-		reg = AUX_BIT_PERIOD_EXPECTED_DELAY(3) |
-		      AUX_HW_RETRY_COUNT_SEL(0) |
-		      AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
+		reg = AUX_BIT_PERIOD_EXPECTED_DELAY(3);
+
+	/* Disable AUX transaction H/W retry */
+	reg |= AUX_HW_RETRY_COUNT_SEL(0) |
+	       AUX_HW_RETRY_INTERVAL_600_MICROSECONDS;
+
 	writel(reg, dp->reg_base + ANALOGIX_DP_AUX_HW_RETRY_CTL);
 
 	/* Receive AUX Channel DEFER commands equal to DEFFER_COUNT*64 */
-- 
2.16.1

[PATCH v4 29/38] drm/rockchip: pre dither down when output bpc is 8bit

[Enric Balletbo i Serra]

From: Mark Yao <mark.yao@rock-chips.com>

Some encoder have a crc verification check, crc check fail if
input and output data is not equal.

That means encoder input and output need use same color depth,
vop can output 10bit data to encoder, but some panel only support
8bit depth, that would make crc check die.

So pre dither down vop data to 8bit if panel's bpc is 8.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict in rockchip_drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c | 2 ++
 drivers/gpu/drm/rockchip/rockchip_drm_drv.h     | 1 +
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c     | 6 ++++++
 drivers/gpu/drm/rockchip/rockchip_drm_vop.h     | 1 +
 drivers/gpu/drm/rockchip/rockchip_vop_reg.c     | 1 +
 5 files changed, 11 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index 8c884f9ce713..b3f46ed24cdc 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -218,6 +218,7 @@ rockchip_dp_drm_encoder_atomic_check(struct drm_encoder *encoder,
 				      struct drm_connector_state *conn_state)
 {
 	struct rockchip_crtc_state *s = to_rockchip_crtc_state(crtc_state);
+	struct drm_display_info *di = &conn_state->connector->display_info;
 
 	/*
 	 * The hardware IC designed that VOP must output the RGB10 video
@@ -229,6 +230,7 @@ rockchip_dp_drm_encoder_atomic_check(struct drm_encoder *encoder,
 
 	s->output_mode = ROCKCHIP_OUT_MODE_AAAA;
 	s->output_type = DRM_MODE_CONNECTOR_eDP;
+	s->output_bpc = di->bpc;
 
 	return 0;
 }
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
index 9c064a40458b..3a6ebfc26036 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_drv.h
@@ -36,6 +36,7 @@ struct rockchip_crtc_state {
 	struct drm_crtc_state base;
 	int output_type;
 	int output_mode;
+	int output_bpc;
 };
 #define to_rockchip_crtc_state(s) \
 		container_of(s, struct rockchip_crtc_state, base)
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
index 184f980679af..42562ab04bde 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c
@@ -928,6 +928,12 @@ static void vop_crtc_atomic_enable(struct drm_crtc *crtc,
 	if (s->output_mode == ROCKCHIP_OUT_MODE_AAAA &&
 	    !(vop_data->feature & VOP_FEATURE_OUTPUT_RGB10))
 		s->output_mode = ROCKCHIP_OUT_MODE_P888;
+
+	if (s->output_mode == ROCKCHIP_OUT_MODE_AAAA && s->output_bpc == 8)
+		VOP_REG_SET(vop, common, pre_dither_down, 1);
+	else
+		VOP_REG_SET(vop, common, pre_dither_down, 0);
+
 	VOP_REG_SET(vop, common, out_mode, s->output_mode);
 
 	VOP_REG_SET(vop, modeset, htotal_pw, (htotal << 16) | hsync_len);
diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h
index 56bbd2e2a8ef..084acdd0019a 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.h
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.h
@@ -67,6 +67,7 @@ struct vop_common {
 	struct vop_reg cfg_done;
 	struct vop_reg dsp_blank;
 	struct vop_reg data_blank;
+	struct vop_reg pre_dither_down;
 	struct vop_reg dither_down;
 	struct vop_reg dither_up;
 	struct vop_reg gate_en;
diff --git a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c
index 2e4eea3459fe..08023d3ecb76 100644
--- a/drivers/gpu/drm/rockchip/rockchip_vop_reg.c
+++ b/drivers/gpu/drm/rockchip/rockchip_vop_reg.c
@@ -264,6 +264,7 @@ static const struct vop_common rk3288_common = {
 	.standby = VOP_REG_SYNC(RK3288_SYS_CTRL, 0x1, 22),
 	.gate_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 23),
 	.mmu_en = VOP_REG(RK3288_SYS_CTRL, 0x1, 20),
+	.pre_dither_down = VOP_REG(RK3288_DSP_CTRL1, 0x1, 1),
 	.dither_down = VOP_REG(RK3288_DSP_CTRL1, 0xf, 1),
 	.dither_up = VOP_REG(RK3288_DSP_CTRL1, 0x1, 6),
 	.data_blank = VOP_REG(RK3288_DSP_CTRL0, 0x1, 19),
-- 
2.16.1

[PATCH v4 30/38] drm/bridge: analogix_dp: Split the platform-specific poweron in two parts

[Enric Balletbo i Serra]

From: Douglas Anderson <dianders@chromium.org>

Some of the platform-specific stuff in rockchip_dp_poweron() needs to
happen before the generic code.  Some needs to happen after.  Let's
split the callback in two.

Specifically we can't start doing PSR work until _after_ the whole
controller is up, so don't set the enable until the end.

Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[seanpaul added exynos change]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c |  7 +++++--
 drivers/gpu/drm/exynos/exynos_dp.c                 |  2 +-
 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    | 12 ++++++++++--
 include/drm/bridge/analogix_dp.h                   |  3 ++-
 4 files changed, 18 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
index edaca650e6d2..8703c3cc5ff8 100644
--- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
+++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
@@ -1260,8 +1260,8 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 		goto out_dp_clk_pre;
 	}
 
-	if (dp->plat_data->power_on)
-		dp->plat_data->power_on(dp->plat_data);
+	if (dp->plat_data->power_on_start)
+		dp->plat_data->power_on_start(dp->plat_data);
 
 	phy_power_on(dp->phy);
 
@@ -1286,6 +1286,9 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
 		goto out_dp_init;
 	}
 
+	if (dp->plat_data->power_on_end)
+		dp->plat_data->power_on_end(dp->plat_data);
+
 	enable_irq(dp->irq);
 	return 0;
 
diff --git a/drivers/gpu/drm/exynos/exynos_dp.c b/drivers/gpu/drm/exynos/exynos_dp.c
index 964831dab102..86330f396784 100644
--- a/drivers/gpu/drm/exynos/exynos_dp.c
+++ b/drivers/gpu/drm/exynos/exynos_dp.c
@@ -162,7 +162,7 @@ static int exynos_dp_bind(struct device *dev, struct device *master, void *data)
 	dp->drm_dev = drm_dev;
 
 	dp->plat_data.dev_type = EXYNOS_DP;
-	dp->plat_data.power_on = exynos_dp_poweron;
+	dp->plat_data.power_on_start = exynos_dp_poweron;
 	dp->plat_data.power_off = exynos_dp_poweroff;
 	dp->plat_data.attach = exynos_dp_bridge_attach;
 	dp->plat_data.get_modes = exynos_dp_get_modes;
diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index b3f46ed24cdc..23317a2269e1 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -109,7 +109,7 @@ static int rockchip_dp_pre_init(struct rockchip_dp_device *dp)
 	return 0;
 }
 
-static int rockchip_dp_poweron(struct analogix_dp_plat_data *plat_data)
+static int rockchip_dp_poweron_start(struct analogix_dp_plat_data *plat_data)
 {
 	struct rockchip_dp_device *dp = to_dp(plat_data);
 	int ret;
@@ -127,6 +127,13 @@ static int rockchip_dp_poweron(struct analogix_dp_plat_data *plat_data)
 		return ret;
 	}
 
+	return ret;
+}
+
+static int rockchip_dp_poweron_end(struct analogix_dp_plat_data *plat_data)
+{
+	struct rockchip_dp_device *dp = to_dp(plat_data);
+
 	return rockchip_drm_psr_activate(&dp->encoder);
 }
 
@@ -330,7 +337,8 @@ static int rockchip_dp_bind(struct device *dev, struct device *master,
 	dp->plat_data.encoder = &dp->encoder;
 
 	dp->plat_data.dev_type = dp->data->chip_type;
-	dp->plat_data.power_on = rockchip_dp_poweron;
+	dp->plat_data.power_on_start = rockchip_dp_poweron_start;
+	dp->plat_data.power_on_end = rockchip_dp_poweron_end;
 	dp->plat_data.power_off = rockchip_dp_powerdown;
 	dp->plat_data.get_modes = rockchip_dp_get_modes;
 
diff --git a/include/drm/bridge/analogix_dp.h b/include/drm/bridge/analogix_dp.h
index e9a1116d2f8e..475b706b49de 100644
--- a/include/drm/bridge/analogix_dp.h
+++ b/include/drm/bridge/analogix_dp.h
@@ -33,7 +33,8 @@ struct analogix_dp_plat_data {
 	struct drm_connector *connector;
 	bool skip_connector;
 
-	int (*power_on)(struct analogix_dp_plat_data *);
+	int (*power_on_start)(struct analogix_dp_plat_data *);
+	int (*power_on_end)(struct analogix_dp_plat_data *);
 	int (*power_off)(struct analogix_dp_plat_data *);
 	int (*attach)(struct analogix_dp_plat_data *, struct drm_bridge *,
 		      struct drm_connector *);
-- 
2.16.1

[PATCH v4 31/38] drm/rockchip: analogix_dp: Do not call Analogix code before bind

[Enric Balletbo i Serra]

From: Tomasz Figa <tfiga@chromium.org>

Driver callbacks, such as system suspend or resume can be called any
time, specifically they can be called before the component bind
callback. Let's use dp->adp pointer as a safeguard and skip calling
Analogix entry points if it is an ERR_PTR().

Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
index 23317a2269e1..6d45d62466b3 100644
--- a/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
+++ b/drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
@@ -368,6 +368,8 @@ static void rockchip_dp_unbind(struct device *dev, struct device *master,
 	analogix_dp_unbind(dp->adp);
 	rockchip_drm_psr_unregister(&dp->encoder);
 	dp->encoder.funcs->destroy(&dp->encoder);
+
+	dp->adp = ERR_PTR(-ENODEV);
 }
 
 static const struct component_ops rockchip_dp_component_ops = {
@@ -391,6 +393,7 @@ static int rockchip_dp_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	dp->dev = dev;
+	dp->adp = ERR_PTR(-ENODEV);
 	dp->plat_data.panel = panel;
 
 	ret = rockchip_dp_of_probe(dp);
@@ -414,6 +417,9 @@ static int rockchip_dp_suspend(struct device *dev)
 {
 	struct rockchip_dp_device *dp = dev_get_drvdata(dev);
 
+	if (IS_ERR(dp->adp))
+		return 0;
+
 	return analogix_dp_suspend(dp->adp);
 }
 
@@ -421,6 +427,9 @@ static int rockchip_dp_resume(struct device *dev)
 {
 	struct rockchip_dp_device *dp = dev_get_drvdata(dev);
 
+	if (IS_ERR(dp->adp))
+		return 0;
+
 	return analogix_dp_resume(dp->adp);
 }
 #endif
-- 
2.16.1

[PATCH v4 32/38] drm/rockchip: Disable PSR on input events

[Enric Balletbo i Serra]

From: "Kristian H. Kristensen" <hoegsberg@google.com>

To improve PSR exit latency, we speculatively start exiting when we
receive input events. Occasionally, this may lead to false positives,
but most of the time we get a head start on coming out of PSR. Depending
on how userspace takes to produce a new frame in response to the event,
this can completely hide the exit latency. In case of Chrome OS, we
typically get the input notifier 50ms or more before the dirty_fb
triggered exit.

Signed-off-by: Kristian H. Kristensen <hoegsberg@google.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
---

 drivers/gpu/drm/rockchip/rockchip_drm_psr.c | 134 ++++++++++++++++++++++++++++
 1 file changed, 134 insertions(+)

diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
index 9376f4396b6b..a107845ba97c 100644
--- a/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
+++ b/drivers/gpu/drm/rockchip/rockchip_drm_psr.c
@@ -12,6 +12,8 @@
  * GNU General Public License for more details.
  */
 
+#include <linux/input.h>
+
 #include <drm/drmP.h>
 #include <drm/drm_crtc_helper.h>
 
@@ -35,6 +37,9 @@ struct psr_drv {
 	enum psr_state		state;
 
 	struct delayed_work	flush_work;
+	struct work_struct	disable_work;
+
+	struct input_handler    input_handler;
 
 	int (*set)(struct drm_encoder *encoder, bool enable);
 };
@@ -133,6 +138,18 @@ static void psr_flush_handler(struct work_struct *work)
 	mutex_unlock(&psr->lock);
 }
 
+static void psr_disable_handler(struct work_struct *work)
+{
+	struct psr_drv *psr = container_of(work, struct psr_drv, disable_work);
+
+	/* If the state has changed since we initiated the flush, do nothing */
+	mutex_lock(&psr->lock);
+	if (psr->state == PSR_ENABLE)
+		psr_set_state_locked(psr, PSR_FLUSH);
+	mutex_unlock(&psr->lock);
+	mod_delayed_work(system_wq, &psr->flush_work, PSR_FLUSH_TIMEOUT_MS);
+}
+
 /**
  * rockchip_drm_psr_activate - activate PSR on the given pipe
  * @encoder: encoder to obtain the PSR encoder
@@ -173,6 +190,7 @@ int rockchip_drm_psr_deactivate(struct drm_encoder *encoder)
 	psr->active = false;
 	mutex_unlock(&psr->lock);
 	cancel_delayed_work_sync(&psr->flush_work);
+	cancel_work_sync(&psr->disable_work);
 
 	return 0;
 }
@@ -226,6 +244,95 @@ void rockchip_drm_psr_flush_all(struct drm_device *dev)
 }
 EXPORT_SYMBOL(rockchip_drm_psr_flush_all);
 
+static void psr_input_event(struct input_handle *handle,
+			    unsigned int type, unsigned int code,
+			    int value)
+{
+	struct psr_drv *psr = handle->handler->private;
+
+	schedule_work(&psr->disable_work);
+}
+
+static int psr_input_connect(struct input_handler *handler,
+			     struct input_dev *dev,
+			     const struct input_device_id *id)
+{
+	struct input_handle *handle;
+	int error;
+
+	handle = kzalloc(sizeof(struct input_handle), GFP_KERNEL);
+	if (!handle)
+		return -ENOMEM;
+
+	handle->dev = dev;
+	handle->handler = handler;
+	handle->name = "rockchip-psr";
+
+	error = input_register_handle(handle);
+	if (error)
+		goto err2;
+
+	error = input_open_device(handle);
+	if (error)
+		goto err1;
+
+	return 0;
+
+err1:
+	input_unregister_handle(handle);
+err2:
+	kfree(handle);
+	return error;
+}
+
+static void psr_input_disconnect(struct input_handle *handle)
+{
+	input_close_device(handle);
+	input_unregister_handle(handle);
+	kfree(handle);
+}
+
+/* Same device ids as cpu-boost */
+static const struct input_device_id psr_ids[] = {
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT |
+			 INPUT_DEVICE_ID_MATCH_ABSBIT,
+		.evbit = { BIT_MASK(EV_ABS) },
+		.absbit = { [BIT_WORD(ABS_MT_POSITION_X)] =
+			    BIT_MASK(ABS_MT_POSITION_X) |
+			    BIT_MASK(ABS_MT_POSITION_Y) },
+	}, /* multi-touch touchscreen */
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT,
+		.evbit = { BIT_MASK(EV_ABS) },
+		.absbit = { [BIT_WORD(ABS_X)] = BIT_MASK(ABS_X) }
+
+	}, /* stylus or joystick device */
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT,
+		.evbit = { BIT_MASK(EV_KEY) },
+		.keybit = { [BIT_WORD(BTN_LEFT)] = BIT_MASK(BTN_LEFT) },
+	}, /* pointer (e.g. trackpad, mouse) */
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT,
+		.evbit = { BIT_MASK(EV_KEY) },
+		.keybit = { [BIT_WORD(KEY_ESC)] = BIT_MASK(KEY_ESC) },
+	}, /* keyboard */
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT |
+				INPUT_DEVICE_ID_MATCH_KEYBIT,
+		.evbit = { BIT_MASK(EV_KEY) },
+		.keybit = {[BIT_WORD(BTN_JOYSTICK)] = BIT_MASK(BTN_JOYSTICK) },
+	}, /* joysticks not caught by ABS_X above */
+	{
+		.flags = INPUT_DEVICE_ID_MATCH_EVBIT |
+				INPUT_DEVICE_ID_MATCH_KEYBIT,
+		.evbit = { BIT_MASK(EV_KEY) },
+		.keybit = { [BIT_WORD(BTN_GAMEPAD)] = BIT_MASK(BTN_GAMEPAD) },
+	}, /* gamepad */
+	{ },
+};
+
 /**
  * rockchip_drm_psr_register - register encoder to psr driver
  * @encoder: encoder that obtain the PSR function
@@ -239,6 +346,7 @@ int rockchip_drm_psr_register(struct drm_encoder *encoder,
 {
 	struct rockchip_drm_private *drm_drv = encoder->dev->dev_private;
 	struct psr_drv *psr;
+	int error;
 
 	if (!encoder || !psr_set)
 		return -EINVAL;
@@ -248,6 +356,7 @@ int rockchip_drm_psr_register(struct drm_encoder *encoder,
 		return -ENOMEM;
 
 	INIT_DELAYED_WORK(&psr->flush_work, psr_flush_handler);
+	INIT_WORK(&psr->disable_work, psr_disable_handler);
 	mutex_init(&psr->lock);
 
 	psr->active = true;
@@ -255,11 +364,33 @@ int rockchip_drm_psr_register(struct drm_encoder *encoder,
 	psr->encoder = encoder;
 	psr->set = psr_set;
 
+	psr->input_handler.event = psr_input_event;
+	psr->input_handler.connect = psr_input_connect;
+	psr->input_handler.disconnect = psr_input_disconnect;
+	psr->input_handler.name =
+		kasprintf(GFP_KERNEL, "rockchip-psr-%s", encoder->name);
+	if (!psr->input_handler.name) {
+		error = -ENOMEM;
+		goto err2;
+	}
+	psr->input_handler.id_table = psr_ids;
+	psr->input_handler.private = psr;
+
+	error = input_register_handler(&psr->input_handler);
+	if (error)
+		goto err1;
+
 	mutex_lock(&drm_drv->psr_list_lock);
 	list_add_tail(&psr->list, &drm_drv->psr_list);
 	mutex_unlock(&drm_drv->psr_list_lock);
 
 	return 0;
+
+ err1:
+	kfree(psr->input_handler.name);
+ err2:
+	kfree(psr);
+	return error;
 }
 EXPORT_SYMBOL(rockchip_drm_psr_register);
 
@@ -279,8 +410,11 @@ void rockchip_drm_psr_unregister(struct drm_encoder *encoder)
 	mutex_lock(&drm_drv->psr_list_lock);
 	list_for_each_entry_safe(psr, n, &drm_drv->psr_list, list) {
 		if (psr->encoder == encoder) {
+			input_unregister_handler(&psr->input_handler);
 			cancel_delayed_work_sync(&psr->flush_work);
+			cancel_work_sync(&psr->disable_work);
 			list_del(&psr->list);
+			kfree(psr->input_handler.name);
 			kfree(psr);
 		}
 	}
-- 
2.16.1

Re: [PATCH v4 15/38] drm/bridge: analogix_dp: Ensure edp is disabled when shutting down the panel

[Marek Szyprowski]

Hi All,

This is the patch, which introduces the issue I've pointed here:

https://lists.freedesktop.org/archives/dri-devel/2018-March/167794.html

On 2018-03-05 23:23, Enric Balletbo i Serra wrote:
> From: Lin Huang <hl@rock-chips.com>
>
> When panel is shut down, we should make sure edp can be disabled to avoid
> undefined behavior.
>
> Cc: Stéphane Marchesin <marcheu@chromium.org>
> Signed-off-by: Lin Huang <hl@rock-chips.com>
> Signed-off-by: zain wang <wzz@rock-chips.com>
> Signed-off-by: Sean Paul <seanpaul@chromium.org>
> Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> ---
>
>   drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 11 +++++++++++
>   1 file changed, 11 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> index 92fb9a072cb6..9b7d530ad24c 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> @@ -1160,6 +1160,12 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
>   
>   	pm_runtime_get_sync(dp->dev);
>   
> +	ret = clk_prepare_enable(dp->clock);
> +	if (ret < 0) {
> +		DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret);
> +		goto out_dp_clk_pre;
> +	}
> +
>   	if (dp->plat_data->power_on)
>   		dp->plat_data->power_on(dp->plat_data);
>   
> @@ -1191,6 +1197,8 @@ static int analogix_dp_set_bridge(struct analogix_dp_device *dp)
>   	phy_power_off(dp->phy);
>   	if (dp->plat_data->power_off)
>   		dp->plat_data->power_off(dp->plat_data);
> +	clk_disable_unprepare(dp->clock);
> +out_dp_clk_pre:
>   	pm_runtime_put_sync(dp->dev);
>   
>   	return ret;
> @@ -1234,10 +1242,13 @@ static void analogix_dp_bridge_disable(struct drm_bridge *bridge)
>   
>   	disable_irq(dp->irq);
>   	phy_power_off(dp->phy);
> +	analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);

In case of Exynos DP, external PHY is used to power the DP block, so no
register access should be performed after phy_power_off(). Please move
analogix_dp_set_analog_power_down() before phy_power_off().

>   
>   	if (dp->plat_data->power_off)
>   		dp->plat_data->power_off(dp->plat_data);
>   
> +	clk_disable_unprepare(dp->clock);
> +
>   	pm_runtime_put_sync(dp->dev);
>   
>   	ret = analogix_dp_prepare_panel(dp, false, true);

Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland

Re: [PATCH v4 15/38] drm/bridge: analogix_dp: Ensure edp is disabled when shutting down the panel

[Enric Balletbo i Serra]

Hi Marek,

On 06/03/18 08:35, Marek Szyprowski wrote:
> Hi All,
> 
> This is the patch, which introduces the issue I've pointed here:
> 
> https://lists.freedesktop.org/archives/dri-devel/2018-March/167794.html
> 
> On 2018-03-05 23:23, Enric Balletbo i Serra wrote:
>> From: Lin Huang <hl@rock-chips.com>
>>
>> When panel is shut down, we should make sure edp can be disabled to avoid
>> undefined behavior.
>>
>> Cc: Stéphane Marchesin <marcheu@chromium.org>
>> Signed-off-by: Lin Huang <hl@rock-chips.com>
>> Signed-off-by: zain wang <wzz@rock-chips.com>
>> Signed-off-by: Sean Paul <seanpaul@chromium.org>
>> Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
>> Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
>> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
>> ---
>>
>>   drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 11 +++++++++++
>>   1 file changed, 11 insertions(+)
>>
>> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>> b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>> index 92fb9a072cb6..9b7d530ad24c 100644
>> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>> @@ -1160,6 +1160,12 @@ static int analogix_dp_set_bridge(struct
>> analogix_dp_device *dp)
>>         pm_runtime_get_sync(dp->dev);
>>   +    ret = clk_prepare_enable(dp->clock);
>> +    if (ret < 0) {
>> +        DRM_ERROR("Failed to prepare_enable the clock clk [%d]\n", ret);
>> +        goto out_dp_clk_pre;
>> +    }
>> +
>>       if (dp->plat_data->power_on)
>>           dp->plat_data->power_on(dp->plat_data);
>>   @@ -1191,6 +1197,8 @@ static int analogix_dp_set_bridge(struct
>> analogix_dp_device *dp)
>>       phy_power_off(dp->phy);
>>       if (dp->plat_data->power_off)
>>           dp->plat_data->power_off(dp->plat_data);
>> +    clk_disable_unprepare(dp->clock);
>> +out_dp_clk_pre:
>>       pm_runtime_put_sync(dp->dev);
>>         return ret;
>> @@ -1234,10 +1242,13 @@ static void analogix_dp_bridge_disable(struct
>> drm_bridge *bridge)
>>         disable_irq(dp->irq);
>>       phy_power_off(dp->phy);
>> +    analogix_dp_set_analog_power_down(dp, POWER_ALL, 1);
> 
> In case of Exynos DP, external PHY is used to power the DP block, so no
> register access should be performed after phy_power_off(). Please move
> analogix_dp_set_analog_power_down() before phy_power_off().
> 

Oh, sorry, I missed that change, I'll include in next version, but I will wait a
little bit more before send for if I receive feedback on the others patches.


>>         if (dp->plat_data->power_off)
>>           dp->plat_data->power_off(dp->plat_data);
>>   +    clk_disable_unprepare(dp->clock);
>> +
>>       pm_runtime_put_sync(dp->dev);
>>         ret = analogix_dp_prepare_panel(dp, false, true);
> 
> Best regards
Enric

Re: [PATCH v4 00/38] DRM Rockchip rk3399 (Kevin)

[Marek Szyprowski]

Hi Enric,

On 2018-03-05 23:22, Enric Balletbo i Serra wrote:
> Hi,
>
> This patchset includes cleanups, improvements, and bug fixes for
> Rockchip DRM driver and PSR support.
>
> This new version is the same as before but rebased on top of
> drm-misc-next plus the Marek patches that fixes Chromebook2 Peach-Pit [1]
> and the latest series of Rockchip rk3399 eDP support [2].
>
> [1] https://www.spinics.net/lists/dri-devel/msg167804.html
> [2] https://www.spinics.net/lists/dri-devel/msg167770.html

Thanks for v4 of this patchset.

After fixing the issue pointed in the patch 15/38, everything works fine on
Exynos5250-based Chromebook Snow and Exynos5420-based Chromebook2 Peach-Pit
boards. You can add my:

Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>

> Regards,
>   Enric
>
> Changes in v4:
> - Rebased all on top of drm-misc-next
> - Removed the following patches as are already applied.
>    [PATCH v3 01/43] drm/rockchip: Get rid of unnecessary struct fields
>    [PATCH v3 02/43] drm/rockchip: support prime import sg table
>    [PATCH v3 03/43] drm/rockchip: Respect page offset for PRIME mmap
>    calls
> - Removed the following patches as now are part of another patchset
>    [PATCH v3 05/43] drm/bridge: analogix_dp: Don't power bridge in
>    analogix_dp_bind
>    [PATCH v3 33/43] drm/panel: simple: Change mode for Sharp lq123p1jx31
>
> Changes in v3:
> - Addressed some of the comments from Sean on the v2
>
> Changes in v2:
> - A few patches have been replaced by newer and cleaner versions from
>    the ChromeOS kernel gerrit, especially about disallowing PSR for the
>    whole atomic commit.
>
>
> Douglas Anderson (4):
>    drm/bridge: analogix_dp: Reorder plat_data->power_off to happen sooner
>    drm/bridge: analogix_dp: Properly log AUX CH errors
>    drm/bridge: analogix_dp: Properly disable aux chan retries on rockchip
>    drm/bridge: analogix_dp: Split the platform-specific poweron in two
>      parts
>
> Kristian H. Kristensen (1):
>    drm/rockchip: Disable PSR on input events
>
> Lin Huang (6):
>    drm/bridge: analogix_dp: Move enable video into config_video()
>    drm/bridge: analogix_dp: Check AUX_EN status when doing AUX transfer
>    drm/bridge: analogix_dp: Ensure edp is disabled when shutting down the
>      panel
>    drm/bridge: analogix_dp: Extend hpd check time to 100ms
>    drm/bridge: analogix_dp: Check dpcd write/read status
>    drm/bridge: analogix_dp: Reset aux channel if an error occurred
>
> Mark Yao (1):
>    drm/rockchip: pre dither down when output bpc is 8bit
>
> Sean Paul (2):
>    drm/rockchip: Don't use atomic constructs for psr
>    drm/rockchip: Remove analogix psr worker
>
> Tomasz Figa (7):
>    drm/rockchip: analogix_dp: Do not call Analogix code before bind
>    drm/rockchip: Cancel PSR enable work before changing the state
>    drm/rockchip: psr: Avoid redundant calls to .set() callback
>    drm/rockchip: psr: Sanitize semantics of allow/disallow API
>    drm/rockchip: Disable PSR from reboot notifier
>    drm/rockchip: Disallow PSR for the whole atomic commit
>    drm/rockchip: psr: Remove flush by CRTC
>
> Yakir Yang (1):
>    drm/bridge: analogix_dp: detect Sink PSR state after configuring the
>      PSR
>
> zain wang (16):
>    drm/bridge: analogix_dp: set psr activate/deactivate when
>      enable/disable bridge
>    drm/bridge: analogix_dp: Don't change psr while bridge is disabled
>    drm/rockchip: add mutex vop lock
>    drm/bridge: analogix_dp: add fast link train for eDP
>    drm/rockchip: Only wait for panel ACK on PSR entry
>    drm/bridge: analogix_dp: Don't use fast link training when panel just
>      powered up
>    drm/bridge: analogix_dp: Retry bridge enable when it failed
>    drm/bridge: analogix_dp: Wait for HPD signal before configuring link
>    drm/bridge: analogix_dp: Set PD_INC_BG first when powering up edp phy
>    drm/bridge: analogix_dp: Fix incorrect usage of enhanced mode
>    drm/bridge: analogix_dp: Fix AUX_PD bit for Rockchip
>    drm/rockchip: Restore psr->state when enable/disable psr failed
>    drm/bridge: analogix_dp: Don't use ANALOGIX_DP_PLL_CTL to control pll
>    drm/bridge: analogix_dp: Fix timeout of video streamclk config
>    drm/bridge: analogix_dp: Fix incorrect operations with register
>      ANALOGIX_DP_FUNC_EN_1
>    drm/bridge: analogix_dp: Move fast link training detect to set_bridge
>
>   drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 452 ++++++++++++++++-----
>   drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  14 +-
>   drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 274 ++++++++-----
>   drivers/gpu/drm/bridge/analogix/analogix_dp_reg.h  |   7 +
>   drivers/gpu/drm/exynos/exynos_dp.c                 |   2 +-
>   drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    |  73 ++--
>   drivers/gpu/drm/rockchip/rockchip_drm_drv.c        |   2 +-
>   drivers/gpu/drm/rockchip/rockchip_drm_drv.h        |   3 +-
>   drivers/gpu/drm/rockchip/rockchip_drm_fb.c         |  61 ++-
>   drivers/gpu/drm/rockchip/rockchip_drm_psr.c        | 361 ++++++++++------
>   drivers/gpu/drm/rockchip/rockchip_drm_psr.h        |   7 +-
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.c        |  47 ++-
>   drivers/gpu/drm/rockchip/rockchip_drm_vop.h        |   1 +
>   drivers/gpu/drm/rockchip/rockchip_vop_reg.c        |   1 +
>   include/drm/bridge/analogix_dp.h                   |   5 +-
>   15 files changed, 915 insertions(+), 395 deletions(-)
>

Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland

Re: [PATCH v4 01/38] drm/bridge: analogix_dp: set psr activate/deactivate when enable/disable bridge

[Heiko Stuebner]

Am Montag, 5. März 2018, 23:22:53 CET schrieb Enric Balletbo i Serra:
> From: zain wang <wzz@rock-chips.com>
> 
> There's a race between when bridge_disable and when vop_crtc_disable
> are called. If the flush timer triggers a new psr work between these,
> we will operate eDP without power shutdowned by bridge_disable. In this
> case, moving activate/deactivate to enable/disable bridge to avoid it.
> 
> Cc: Stéphane Marchesin <marcheu@chromium.org>
> Signed-off-by: zain wang <wzz@rock-chips.com>
> Signed-off-by: Caesar Wang <wxt@rock-chips.com>
> Signed-off-by: Sean Paul <seanpaul@chromium.org>
> Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>

adapted the subject to drm/rockchip, as it only touches the rockchip
glue driver for the analogix_dp and applied to drm-misc-next after
checking on both pinky (rk3288) and kevin (rk3399).


Heiko

Re: [PATCH v4 02/38] drm/rockchip: Don't use atomic constructs for psr

[Heiko Stuebner]

Am Montag, 5. März 2018, 23:22:54 CET schrieb Enric Balletbo i Serra:
> From: Sean Paul <seanpaul@chromium.org>
> 
> Instead of using timer and spinlocks, use delayed_work and
> mutexes for rockchip psr. This allows us to make blocking
> calls when enabling/disabling psr (which is sort of important
> given we're talking over dpcd to the display).
> 
> Cc: Caesar Wang <wxt@rock-chips.com>
> Cc: 征增 王 <wzz@rock-chips.com>
> Cc: Stéphane Marchesin <marcheu@chromium.org>
> Signed-off-by: Sean Paul <seanpaul@chromium.org>
> Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>

applied to drm-misc-next after
checking on both pinky (rk3288) and kevin (rk3399).


Heiko

Re: [PATCH v4 03/38] drm/bridge: analogix_dp: detect Sink PSR state after configuring the PSR

[Heiko Stuebner]

Hi Enric,

Am Montag, 5. März 2018, 23:22:55 CET schrieb Enric Balletbo i Serra:
> From: Yakir Yang <ykk@rock-chips.com>
> 
> Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
> function, or print the sink PSR error state if we failed to apply the
> requested PSR setting.
> 
> Cc: 征增 王 <wzz@rock-chips.com>
> Cc: Stéphane Marchesin <marcheu@chromium.org>
> Signed-off-by: Yakir Yang <ykk@rock-chips.com>
> [seanpaul changed timeout loop to a readx poll]
> Signed-off-by: Sean Paul <seanpaul@chromium.org>
> Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>

as this modifies the generic part of the analogix_dp, I think we'll
need some form of Ack from the drm-bridge maintainers.
[Or bridge maintainers applying it].
Change itself looks good, at least to me :-) .

It seems your recipient list is missing some bridge maintainers though.
MAINTAINERS, tells us that
	Archit Taneja <architt@codeaurora.org>
	Andrzej Hajda <a.hajda@samsung.com>
	Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
should be CCed, but right now I only see Archit.

As there are quite a lot of general patches in here, I'd think this calls
for a v5, including Mareks tested-tag and including the missing people.


Heiko

> 
>  drivers/gpu/drm/bridge/analogix/analogix_dp_core.c |  6 ++--
>  drivers/gpu/drm/bridge/analogix/analogix_dp_core.h |  6 ++--
>  drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 35 +++++++++++++++++++---
>  3 files changed, 37 insertions(+), 10 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> index a693ab3078f0..e738aa6de1af 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
> @@ -122,8 +122,7 @@ int analogix_dp_enable_psr(struct analogix_dp_device *dp)
>  	psr_vsc.DB0 = 0;
>  	psr_vsc.DB1 = EDP_VSC_PSR_STATE_ACTIVE | EDP_VSC_PSR_CRC_VALUES_VALID;
>  
> -	analogix_dp_send_psr_spd(dp, &psr_vsc);
> -	return 0;
> +	return analogix_dp_send_psr_spd(dp, &psr_vsc);
>  }
>  EXPORT_SYMBOL_GPL(analogix_dp_enable_psr);
>  
> @@ -149,8 +148,7 @@ int analogix_dp_disable_psr(struct analogix_dp_device *dp)
>  	if (ret != 1)
>  		dev_err(dp->dev, "Failed to set DP Power0 %d\n", ret);
>  
> -	analogix_dp_send_psr_spd(dp, &psr_vsc);
> -	return 0;
> +	return analogix_dp_send_psr_spd(dp, &psr_vsc);
>  }
>  EXPORT_SYMBOL_GPL(analogix_dp_disable_psr);
>  
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
> index 5c6a28806129..b039b28d8fcc 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
> @@ -20,6 +20,8 @@
>  #define MAX_CR_LOOP 5
>  #define MAX_EQ_LOOP 5
>  
> +#define DP_TIMEOUT_PSR_LOOP_MS			300
> +
>  /* DP_MAX_LANE_COUNT */
>  #define DPCD_ENHANCED_FRAME_CAP(x)		(((x) >> 7) & 0x1)
>  #define DPCD_MAX_LANE_COUNT(x)			((x) & 0x1f)
> @@ -247,8 +249,8 @@ void analogix_dp_config_video_slave_mode(struct analogix_dp_device *dp);
>  void analogix_dp_enable_scrambling(struct analogix_dp_device *dp);
>  void analogix_dp_disable_scrambling(struct analogix_dp_device *dp);
>  void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp);
> -void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
> -			      struct edp_vsc_psr *vsc);
> +int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
> +			     struct edp_vsc_psr *vsc);
>  ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
>  			     struct drm_dp_aux_msg *msg);
>  
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> index 303083ad28e3..005a3f7005d2 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> @@ -10,10 +10,11 @@
>   * option) any later version.
>   */
>  
> -#include <linux/device.h>
> -#include <linux/io.h>
>  #include <linux/delay.h>
> +#include <linux/device.h>
>  #include <linux/gpio.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
>  
>  #include <drm/bridge/analogix_dp.h>
>  
> @@ -992,10 +993,25 @@ void analogix_dp_enable_psr_crc(struct analogix_dp_device *dp)
>  	writel(PSR_VID_CRC_ENABLE, dp->reg_base + ANALOGIX_DP_CRC_CON);
>  }
>  
> -void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
> -			      struct edp_vsc_psr *vsc)
> +static ssize_t analogix_dp_get_psr_status(struct analogix_dp_device *dp)
> +{
> +	ssize_t val;
> +	u8 status;
> +
> +	val = drm_dp_dpcd_readb(&dp->aux, DP_PSR_STATUS, &status);
> +	if (val < 0) {
> +		dev_err(dp->dev, "PSR_STATUS read failed ret=%zd", val);
> +		return val;
> +	}
> +	return status;
> +}
> +
> +int analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
> +			     struct edp_vsc_psr *vsc)
>  {
>  	unsigned int val;
> +	int ret;
> +	ssize_t psr_status;
>  
>  	/* don't send info frame */
>  	val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
> @@ -1036,6 +1052,17 @@ void analogix_dp_send_psr_spd(struct analogix_dp_device *dp,
>  	val = readl(dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
>  	val |= IF_EN;
>  	writel(val, dp->reg_base + ANALOGIX_DP_PKT_SEND_CTL);
> +
> +	ret = readx_poll_timeout(analogix_dp_get_psr_status, dp, psr_status,
> +		psr_status >= 0 &&
> +		((vsc->DB1 && psr_status == DP_PSR_SINK_ACTIVE_RFB) ||
> +		(!vsc->DB1 && psr_status == DP_PSR_SINK_INACTIVE)), 1500,
> +		DP_TIMEOUT_PSR_LOOP_MS * 1000);
> +	if (ret) {
> +		dev_warn(dp->dev, "Failed to apply PSR %d\n", ret);
> +		return ret;
> +	}
> +	return 0;
>  }
>  
>  ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
>