From: Peter Rosin <peda@axentia.se>
To: Codrin.Ciubotariu@microchip.com, linux-i2c@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org
Cc: Ludovic.Desroches@microchip.com, Nicolas.Ferre@microchip.com,
alexandre.belloni@bootlin.com, robh+dt@kernel.org,
wsa@kernel.org, kamel.bouhara@bootlin.com
Subject: Re: Regression: at24 eeprom writing times out on sama5d3
Date: Fri, 10 Jun 2022 22:51:08 +0200 [thread overview]
Message-ID: <38dedc92-62a2-7365-6fda-95d6404be749@axentia.se> (raw)
In-Reply-To: <2bb4868b-90ab-887e-bf13-9de8b79231bd@microchip.com>
Hi!
2022-06-10 at 09:35, Codrin.Ciubotariu@microchip.com wrote:
> On 09.06.2022 17:28, Peter Rosin wrote:
>> Hi!
>
> Hi Peter,
>
>>
>> I have not actually bisected this issue but reverting the effects of
>> patch a4bd8da893a3 ("ARM: dts: at91: sama5d3: add i2c gpio pinctrl")
>> makes the problem go away.
>>
>> I.e. I need something like this in my dts
>>
>> &i2c2 {
>> status = "okay";
>>
>> pinctrl-names = "default";
>> /delete-property/ pinctrl-1;
>> /delete-property/ sda-gpios;
>> /delete-property/ scl-gpios;
>>
>> eeprom@50 {
>> compatible = "st,24c64", "atmel,24c64";
>> reg = <0x50>;
>> wp-gpios = <&filter_gpio 7 GPIO_ACTIVE_HIGH>;
>> };
>> };
>>
>> for multi-page eeprom writes to not time out (a page is 32 bytes on this
>> eeprom).
>>
>> For reference, the current defaults for this SoC/I2C-bus, that I modify,
>> are:
>>
>> pinctrl-names = "default", "gpio";
>> pinctrl-0 = <&pinctrl_i2c2>;
>> pinctrl-1 = <&pinctrl_i2c2_gpio>;
>> sda-gpios = <&pioA 18 GPIO_ACTIVE_HIGH>;
>> scl-gpios = <&pioA 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>>
>> I suspect that the underlying reason is that the bus recovery takes
>> too long and that the at24 eeprom driver gives up prematurely. I doubt
>> that this is chip specific, but I don't know that.
>>
>> I can work around the issue in user space with by writing in 4 byte
>> chunks, like so
>>
>> dd if=source.file of=/sys/bus/i2c/devices/2-0050/eeprom obs=4
>>
>> but that is really ugly and gets slow too, about 20 seconds to program
>> the full 8kB eeprom. With the above in my dts it takes a second or
>> so (a bit more with dynamic debug active).
>>
>>
>> If I run
>>
>> dd if=source.file of=/sys/bus/i2c/devices/2-0050/eeprom
>>
>> with a source.file of 8kB and the upstream dts properties in place, I can
>> collect the following debug output from at24, i2c-core and i2c-at91:
>>
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@0 --> 0 (-23170)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: Trying i2c bus recovery
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@32 --> -121 (-23169)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@32 --> 0 (-23168)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: Trying i2c bus recovery
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@64 --> -121 (-23168)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@64 --> 0 (-23167)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: Trying i2c bus recovery
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@96 --> -121 (-23167)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: controller timed out
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: Trying i2c bus recovery
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@96 --> -110 (-23155)
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:56:34 me20 kernel: at91_i2c f801c000.i2c: controller timed out
>> Jun 9 15:56:34 me20 kernel: i2c i2c-2: Trying i2c bus recovery
>> Jun 9 15:56:34 me20 kernel: at24 2-0050: write 32@96 --> -110 (-23143)
>>
>> And then there is no more action. I.e. only a couple of 32 byte pages
>> are written.
>>
>> With the above mentioned dts override in place I instead get this, which is
>> a lot more sensible:
>>
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@0 --> 0 (753629)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@32 --> -121 (753629)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@32 --> 0 (753630)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@64 --> -121 (753630)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@64 --> 0 (753631)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@96 --> -121 (753631)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@96 --> 0 (753632)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@128 --> -121 (753632)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@128 --> 0 (753633)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@160 --> -121 (753633)
>> Jun 9 15:48:53 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:53 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:53 me20 kernel: at24 2-0050: write 32@160 --> 0 (753634)
>> ... snip ...
>> Jun 9 15:48:55 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:55 me20 kernel: at24 2-0050: write 32@8128 --> -121 (753883)
>> Jun 9 15:48:55 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:55 me20 kernel: at24 2-0050: write 32@8128 --> 0 (753884)
>> Jun 9 15:48:55 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: received nack
>> Jun 9 15:48:55 me20 kernel: at24 2-0050: write 32@8160 --> -121 (753884)
>> Jun 9 15:48:55 me20 kernel: i2c i2c-2: at91_xfer: processing 1 messages:
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer: write 34 bytes.
>> Jun 9 15:48:55 me20 kernel: at91_i2c f801c000.i2c: transfer complete
>> Jun 9 15:48:55 me20 kernel: at24 2-0050: write 32@8160 --> 0 (753885)
>
> could you please apply this patch-set [1] and let us know if it
> addresses your issue?
>
> Thanks and best regards,
> Codrin
>
> https://patchwork.ozlabs.org/project/linux-i2c/list/?series=255408
That series does indeed help! I'll reply with a tested-by etc on the
first two patches, I can't test patch 3/3 with my sama5d3 board...
Thank you very much!
Cheers,
Peter
next prev parent reply other threads:[~2022-06-10 20:51 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-06-09 14:28 Regression: at24 eeprom writing times out on sama5d3 Peter Rosin
2022-06-10 7:35 ` Codrin.Ciubotariu
2022-06-10 20:51 ` Peter Rosin [this message]
2022-06-30 7:44 ` Peter Rosin
2022-09-08 12:06 ` Thorsten Leemhuis
2022-09-08 13:59 ` Peter Rosin
2022-09-26 13:32 ` Regression: at24 eeprom writing times out on sama5d3 #forregzbot Thorsten Leemhuis
2022-12-15 17:53 ` Regression: at24 eeprom writing times out on sama5d3 Thorsten Leemhuis
2022-12-15 18:50 ` Conor.Dooley
2023-03-15 11:07 ` Linux regression tracking (Thorsten Leemhuis)
2022-06-13 14:58 ` Wolfram Sang
2022-06-13 15:43 ` Peter Rosin
2022-06-13 20:06 ` Wolfram Sang
2022-06-14 8:25 ` Codrin.Ciubotariu
2022-06-14 13:53 ` Codrin.Ciubotariu
2022-06-14 14:25 ` Conor.Dooley
2022-06-15 8:34 ` Codrin.Ciubotariu
2022-06-11 13:41 ` Thorsten Leemhuis
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=38dedc92-62a2-7365-6fda-95d6404be749@axentia.se \
--to=peda@axentia.se \
--cc=Codrin.Ciubotariu@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=kamel.bouhara@bootlin.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=wsa@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).