linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Mohamed DOLLIAZAL <mhd@gxt.com>
To: linux-kernel@vger.kernel.org
Subject: 2.4.2 ext2fs corruption status
Date: Wed, 01 Aug 2001 17:10:09 -0500	[thread overview]
Message-ID: <3B687E41.D969FCC3@gxt.com> (raw)

Hi all,

I am using RH 7.1 with the stock 2.4.2-2 kernel, I got several times my
disk corrupted and even lost the superblock. I have seen a lot messages
about the ext2fs corruption in kernel 2.4.2 but I didn't find what was
causing this problem (hardware or sofware). And if was bug, What kernel
should I use to avoid this problem.

I got these error messages :

EXT2-fs error (device sd(8,8)): ext2_new_block: Allocating block in
system zone - block = 786920
EXT2-fs error (device sd(8,8)): ext2_new_block: Free blocks count
corrupted for block group 3
EXT2-fs error (device sd(8,8)): ext2_readdir: bad entry in directory
#768546: rec_len is smaller than minimal - offset=0, inode=0, rec_len=0,
name_len=0

Here is the the output of   lspci -vv :

00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
(rev 02)
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=4M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
                Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 00007000-00007fff
        Memory behind bridge: de500000-de5fffff
        Prefetchable memory behind bridge: de200000-de2fffff
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
(rev 22)
        Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10)
(prog-if 8a [Master SecP PriP])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 32
        Region 4: I/O ports at ffa0 [size=16]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10)
(prog-if 00 [UHCI])
        Subsystem: Unknown device 0925:1234
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, cache line size 08
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at bc00 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10)
(prog-if 00 [UHCI])
        Subsystem: Unknown device 0925:1234
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, cache line size 08
        Interrupt: pin D routed to IRQ 11
        Region 4: I/O ports at c000 [size=32]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 SMBus: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
30)
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Capabilities: [68] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.5 Multimedia audio controller: VIA Technologies, Inc. AC97 Audio
Controller (rev 20)
        Subsystem: Giga-byte Technology: Unknown device 7600
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin C routed to IRQ 10
        Region 0: I/O ports at cc00 [size=256]
        Region 1: I/O ports at c800 [size=4]
        Region 2: I/O ports at c400 [size=4]
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:09.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03)
(prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64, cache line size 08
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
        I/O behind bridge: 00008000-00009fff
        Memory behind bridge: de600000-deefffff
        Prefetchable memory behind bridge:
00000000de300000-00000000de300000
        BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
        Capabilities: [dc] Power Management version 1
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
                Bridge: PM- B3+

00:0c.0 SCSI storage controller: Adaptec 7892A (rev 02)
        Subsystem: Adaptec: Unknown device e2a0
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (10000ns min, 6250ns max), cache line size 08
        Interrupt: pin A routed to IRQ 9
        BIST result: 00
        Region 0: I/O ports at d000 [disabled] [size=256]
        Region 1: Memory at dfbcf000 (64-bit, non-prefetchable)
[size=4K]
        Expansion ROM at dfba0000 [disabled] [size=128K]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 VGA compatible controller: Trident Microsystems 3DIm`age 975
(rev f3) (prog-if 00 [VGA])
        Subsystem: Trident Microsystems 3DImage 9750
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at dfc00000 (32-bit, non-prefetchable)
[size=4M]
        Region 1: Memory at dfbe0000 (32-bit, non-prefetchable)
[size=128K]
        Region 2: Memory at df400000 (32-bit, non-prefetchable)
[size=4M]
        Expansion ROM at dfbd0000 [disabled] [size=64K]

02:04.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 05)
        Subsystem: Intel Corporation EtherExpress PRO/100+ Dual Port
Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min, 14000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 5
        Region 0: Memory at de3ff000 (32-bit, prefetchable) [size=4K]
        Region 1: I/O ports at 9c00 [size=32]
        Region 2: Memory at dee00000 (32-bit, non-prefetchable)
[size=1M]
        Expansion ROM at ded00000 [disabled] [size=1M]
        Capabilities: [dc] Power Management version 1
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:05.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100]
(rev 05)
        Subsystem: Intel Corporation EtherExpress PRO/100+ Dual Port
Adapter
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (2000ns min, 14000ns max), cache line size 08
        Interrupt: pin A routed to IRQ 10
        Region 0: Memory at de3fe000 (32-bit, prefetchable) [size=4K]
        Region 1: I/O ports at 9800 [size=32]
        Region 2: Memory at dec00000 (32-bit, non-prefetchable)
[size=1M]
        Expansion ROM at deb00000 [disabled] [size=1M]
        Capabilities: [dc] Power Management version 1
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-


Thanks for you help,

Mohamed.


             reply	other threads:[~2001-08-01 22:03 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2001-08-01 22:10 Mohamed DOLLIAZAL [this message]
2001-08-01 22:15 ` 2.4.2 ext2fs corruption status Andreas Dilger
     [not found] <no.id>
2001-08-02  0:20 ` Alan Cox
2001-08-01 19:40   ` Mohamed DOLLIAZAL
2001-08-02 12:27 ` Alan Cox

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3B687E41.D969FCC3@gxt.com \
    --to=mhd@gxt.com \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).