From: Ben Greear <greearb@candelatech.com>
To: "Feldman, Scott" <scott.feldman@intel.com>
Cc: linux-kernel <linux-kernel@vger.kernel.org>,
"'netdev@oss.sgi.com'" <netdev@oss.sgi.com>
Subject: Re: Update on e1000 troubles (over-heating!)
Date: Tue, 08 Oct 2002 11:44:30 -0700 [thread overview]
Message-ID: <3DA3278E.9000800@candelatech.com> (raw)
In-Reply-To: 288F9BF66CD9D5118DF400508B68C44604758AF7@orsmsx113.jf.intel.com
[-- Attachment #1: Type: text/plain, Size: 932 bytes --]
Feldman, Scott wrote:
>>I believe I have figured out why the e1000 crashed my machine
>>after .5 - 1 hours: The NIC was over-heating. I measured
>>one of the NICs after the machine crashed with an external
>>(cheap) temp probe. It registered right at 50 degrees C, and
>>this was about 15-30 seconds after it crashed.
>
>
> Ben, please send lspci -x on the hot nic.
Here is the lspci information, both -x and -vv. This is with two of
the e1000 single-port NICS side-by-side. I have also strapped a P-IV
CPU fan on top of the two cards to blow some air over them....running
tests now to see if that actually helps anything. If it does, I'll
be sure to send you a picture :)
Thanks,
Ben
>
> -scott
>
--
Ben Greear <greearb@candelatech.com> <Ben_Greear AT excite.com>
President of Candela Technologies Inc http://www.candelatech.com
ScryMUD: http://scry.wanfear.com http://scry.wanfear.com/~greear
[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 10779 bytes --]
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11)
00: 22 10 0c 70 06 00 30 22 11 00 00 06 00 40 00 00
10: 08 00 00 f8 08 00 20 f6 91 10 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge
00: 22 10 0d 70 07 00 20 02 00 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 44 f1 01 20 22
20: f0 ff 00 00 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 04 00
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05)
00: 22 10 40 74 0f 00 20 02 05 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04)
00: 22 10 41 74 05 00 00 02 04 8a 01 01 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 f0 00 00 00 00 00 00 00 00 00 00 22 10 41 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
00: 22 10 43 74 00 00 80 02 03 00 80 06 00 40 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 43 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:08.0 Ethernet controller: Intel Corp.: Unknown device 100f (rev 01)
00: 86 80 0f 10 17 00 30 02 01 00 00 02 10 40 00 00
10: 04 00 00 f4 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 10 00 00 00 00 00 00 00 00 00 00 86 80 01 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 ff 00
00:09.0 Ethernet controller: Intel Corp.: Unknown device 100f (rev 01)
00: 86 80 0f 10 17 00 30 02 01 00 00 02 10 40 00 00
10: 04 00 02 f4 00 00 00 00 00 00 00 00 00 00 00 00
20: 41 10 00 00 00 00 00 00 00 00 00 00 86 80 01 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 09 01 ff 00
00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05)
00: 22 10 48 74 17 00 20 22 05 00 04 06 00 63 01 00
10: 00 00 00 00 00 00 00 00 00 02 02 a8 20 20 00 22
20: 10 f4 f0 f5 f0 ff 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 0c 00
02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07)
00: 22 10 49 74 17 00 80 82 07 10 03 0c 00 40 00 00
10: 00 00 10 f4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 49 74
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 04 00 50
02:07.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
00: 02 10 52 47 87 00 90 02 27 00 00 03 10 42 00 00
10: 00 00 00 f5 01 20 00 00 00 10 10 f4 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 08 80
30: 00 00 00 00 5c 00 00 00 00 00 00 00 ff 00 08 00
02:08.0 Ethernet controller: 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T] (rev 78)
00: b7 10 05 98 17 00 10 02 78 00 00 02 10 50 00 00
10: 01 24 00 00 00 20 10 f4 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 62 24
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 0a 0a
02:09.0 Ethernet controller: 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T] (rev 78)
00: b7 10 05 98 17 00 10 02 78 00 00 02 10 50 00 00
10: 81 24 00 00 00 24 10 f4 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 62 24
30: 00 00 00 00 dc 00 00 00 00 00 00 00 05 01 0a 0a
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at f6200000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at 1090 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=x1,x2
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04) (prog-if 8a [Master SecP PriP])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:08.0 Ethernet controller: Intel Corp.: Unknown device 100f (rev 01)
Subsystem: Intel Corp.: Unknown device 1001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 10
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at 1000 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:09.0 Ethernet controller: Intel Corp.: Unknown device 100f (rev 01)
Subsystem: Intel Corp.: Unknown device 1001
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (63750ns min), cache line size 10
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f4020000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at 1040 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [e4] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=0
Status: Bus=0 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, DC=simple, DMMRBC=0, DMOST=0, DMCRS=0, RSCEM-
Capabilities: [f0] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=02, subordinate=02, sec-latency=168
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f4100000-f5ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07) (prog-if 10 [OHCI])
Subsystem: Advanced Micro Devices [AMD] AMD-768 [Opus] USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 64 (20000ns max)
Interrupt: pin D routed to IRQ 10
Region 0: Memory at f4100000 (32-bit, non-prefetchable) [size=4K]
02:07.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) (prog-if 00 [VGA])
Subsystem: ATI Technologies Inc: Unknown device 8008
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 10
Region 0: Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at f4101000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:08.0 Ethernet controller: 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T] (rev 78)
Subsystem: Tyan Computer: Unknown device 2462
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 2400 [size=128]
Region 1: Memory at f4102000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:09.0 Ethernet controller: 3Com Corporation 3c980-TX 10/100baseTX NIC [Python-T] (rev 78)
Subsystem: Tyan Computer: Unknown device 2462
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 (2500ns min, 2500ns max), cache line size 10
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2480 [size=128]
Region 1: Memory at f4102400 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
next prev parent reply other threads:[~2002-10-08 18:40 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-06 7:33 Update on e1000 troubles (over-heating!) Feldman, Scott
2002-10-08 18:44 ` Ben Greear [this message]
-- strict thread matches above, loose matches on Subject: below --
2002-10-15 2:20 Feldman, Scott
2002-10-15 2:37 ` Andi Kleen
2002-10-15 2:54 ` Jonathan Lundell
2002-10-15 5:42 ` Dave Hansen
2002-10-15 7:07 ` Ben Greear
2002-10-15 7:01 ` Ben Greear
2002-10-06 3:38 Ben Greear
2002-10-06 3:47 ` Andre Hedrick
2002-10-06 22:38 ` jamal
2002-10-07 0:14 ` Andre Hedrick
2002-10-07 11:56 ` jamal
2002-10-07 3:46 ` Ben Greear
2002-10-07 5:26 ` David S. Miller
2002-10-07 11:53 ` jamal
2002-10-07 11:58 ` David S. Miller
2002-10-07 16:40 ` Ben Greear
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3DA3278E.9000800@candelatech.com \
--to=greearb@candelatech.com \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@oss.sgi.com \
--cc=scott.feldman@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).