Linux version 2.6.0-test4 (root@aeon) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Sat Aug 23 11:59:23 EDT 2003 Video mode to be used for restore is f00 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fffc000 (usable) BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data) BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. On node 0 totalpages: 131068 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126972 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 ASUS ) @ 0x000f5810 ACPI: RSDT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x1fffc000 ACPI: FADT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x1fffc0c0 ACPI: BOOT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x1fffc030 ACPI: MADT (v001 ASUS P4S8X 0x42302e31 MSFT 0x31313031) @ 0x1fffc058 ACPI: DSDT (v001 ASUS P4S8X 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2 IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, IRQ 0-23 ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x1]) ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x14] polarity[0x3] trigger[0x3]) Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Building zonelist for node : 0 Kernel command line: ro root=LABEL=/ parport=auto nmi_watchdog=1 3 Initializing CPU#0 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2533.827 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 5013.50 BogoMIPS Memory: 513496k/524272k available (2455k kernel code, 10008k reserved, 1052k data, 164k init, 0k highmem) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available CPU#0: Thermal monitoring enabled CPU: Intel(R) Pentium(R) 4 CPU 2.53GHz stepping 04 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX enabled ExtINT on CPU#0 ESR value before enabling vector: 00000000 ESR value after enabling vector: 00000000 ENABLING IO-APIC IRQs init IO_APIC IRQs IO-APIC (apicid-pin) 2-0, 2-9, 2-16, 2-17, 2-18, 2-19, 2-21, 2-22, 2-23 not connected. ..TIMER: vector=0x31 pin1=2 pin2=-1 activating NMI Watchdog ... done. testing NMI watchdog ... OK. number of MP IRQ sources: 15. number of IO-APIC #2 registers: 24. testing the IO APIC....................... IO APIC #2...... .... register #00: 02000000 ....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178080 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0080 .... register #02: 02000000 ....... : arbitration: 02 .... register #03: 00000001 ....... : Boot DT : 1 .... IRQ redirection table: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: 00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 000 00 1 0 0 0 0 0 0 00 0a 001 01 0 0 0 0 0 1 1 71 0b 001 01 0 0 0 0 0 1 1 79 0c 001 01 0 0 0 0 0 1 1 81 0d 001 01 0 0 0 0 0 1 1 89 0e 001 01 0 0 0 0 0 1 1 91 0f 001 01 0 0 0 0 0 1 1 99 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 001 01 1 1 0 1 0 1 1 A1 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00 IRQ to pin mappings: IRQ0 -> 0:2 IRQ1 -> 0:1 IRQ3 -> 0:3 IRQ4 -> 0:4 IRQ5 -> 0:5 IRQ6 -> 0:6 IRQ7 -> 0:7 IRQ8 -> 0:8 IRQ9 -> 0:20 IRQ10 -> 0:10 IRQ11 -> 0:11 IRQ12 -> 0:12 IRQ13 -> 0:13 IRQ14 -> 0:14 IRQ15 -> 0:15 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ... ..... CPU clock speed is 2532.0662 MHz. ..... host bus clock speed is 133.0297 MHz. PM: Adding info for No Bus:legacy Initializing RT netlink socket PCI: PCI BIOS revision 2.10 entry at 0xf11b0, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec pool[0]: 1 bvecs: 256 entries (12 bytes) biovec pool[1]: 4 bvecs: 256 entries (48 bytes) biovec pool[2]: 16 bvecs: 256 entries (192 bytes) biovec pool[3]: 64 bvecs: 256 entries (768 bytes) biovec pool[4]: 128 bvecs: 256 entries (1536 bytes) biovec pool[5]: 256 bvecs: 256 entries (3072 bytes) ACPI: Subsystem revision 20030813 tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:.................................................................................................................................... Table [DSDT](id F004) - 326 Objects with 47 Devices 132 Methods 6 Regions ACPI Namespace successfully loaded at root c052c4dc IOAPIC[0]: Set PCI routing entry (2-20 -> 0xa9 -> IRQ 20 Mode:1 Active:1) evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 15 [_GPE] 2 regs at 000000000000E420 on int 9 evgpeblk-0748 [06] ev_create_gpe_block : GPE 16 to 31 [_GPE] 2 regs at 000000000000E430 on int 9 Completing Region/Field/Buffer/Package initialization:........................................ Initialized 6/6 Regions 0/0 Fields 23/23 Buffers 11/11 Packages (334 nodes) Executing all Device _STA and_INI methods:................................................ 48 Devices found containing: 48 _STA, 1 _INI methods ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 *12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15, enabled at IRQ 9) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PM: Adding info for No Bus:pci0000:00 Enabling SiS 96x SMBus. PM: Adding info for pci:0000:00:00.0 PM: Adding info for pci:0000:00:01.0 PM: Adding info for pci:0000:00:02.0 PM: Adding info for pci:0000:00:02.1 PM: Adding info for pci:0000:00:02.3 PM: Adding info for pci:0000:00:02.5 PM: Adding info for pci:0000:00:02.7 PM: Adding info for pci:0000:00:03.0 PM: Adding info for pci:0000:00:03.1 PM: Adding info for pci:0000:00:03.2 PM: Adding info for pci:0000:00:03.3 PM: Adding info for pci:0000:00:04.0 PM: Adding info for pci:0000:00:0b.0 PM: Adding info for pci:0000:00:0e.0 PM: Adding info for pci:0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00f9680 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x96b0, dseg 0xf0000 PM: Adding info for No Bus:pnp0 PM: Adding info for pnp:00:01 PM: Adding info for pnp:00:02 PM: Adding info for pnp:00:03 PM: Adding info for pnp:00:05 PM: Adding info for pnp:00:06 PM: Adding info for pnp:00:07 PM: Adding info for pnp:00:09 PM: Adding info for pnp:00:0a PM: Adding info for pnp:00:0b PM: Adding info for pnp:00:0c PM: Adding info for pnp:00:0d PM: Adding info for pnp:00:0e PM: Adding info for pnp:00:0f PM: Adding info for pnp:00:10 PM: Adding info for pnp:00:11 PM: Adding info for pnp:00:12 PnPBIOS: 16 nodes reported by PnP BIOS; 16 recorded by driver SCSI subsystem initialized drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub IOAPIC[0]: Set PCI routing entry (2-16 -> 0xb1 -> IRQ 16 Mode:1 Active:1) 00:00:02[A] -> 2-16 -> IRQ 16 IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb9 -> IRQ 17 Mode:1 Active:1) 00:00:02[B] -> 2-17 -> IRQ 17 IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18 Mode:1 Active:1) 00:00:02[C] -> 2-18 -> IRQ 18 IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc9 -> IRQ 19 Mode:1 Active:1) 00:00:02[D] -> 2-19 -> IRQ 19 IOAPIC[0]: Set PCI routing entry (2-21 -> 0xd1 -> IRQ 21 Mode:1 Active:1) 00:00:03[B] -> 2-21 -> IRQ 21 IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1) 00:00:03[C] -> 2-22 -> IRQ 22 IOAPIC[0]: Set PCI routing entry (2-23 -> 0xe1 -> IRQ 23 Mode:1 Active:1) 00:00:03[D] -> 2-23 -> IRQ 23 Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed Pin 2-18 already programmed Pin 2-19 already programmed Pin 2-16 already programmed Pin 2-17 already programmed pci_irq-0299 [19] acpi_pci_irq_derive : Unable to derive IRQ for device 0000:00:03.0 ACPI: No IRQ known for interrupt pin A of device 0000:00:03.0 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' pty: 256 Unix98 ptys configured SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x1 Machine check exception polling timer started. IA-32 Microcode Update Driver: v1.11 VFS: Disk quotas dquot_6.5.1 Journalled Block Device driver loaded Initializing Cryptographic API ACPI: Power Button (FF) [PWRF] acpi_processor-1626 [22] acpi_processor_get_inf: Invalid PBLK length [5] ACPI: Processor [CPU0] (supports C1) PM: Adding info for No Bus:pnp1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.11a parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP] parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) parport0: cpp_daisy: aa5500ff(38) parport0: assign_addrs: aa5500ff(38) Using anticipatory scheduling elevator Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 PM: Adding info for platform:floppy0 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SIS5513: IDE controller at PCI slot 0000:00:02.5 SIS5513: chipset revision 0 SIS5513: not 100% native mode: will probe irqs later SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:DMA, hdd:pio hda: Maxtor 6Y080P0, ATA DISK drive PM: Adding info for No Bus:ide0 hdb: Maxtor 53073H6, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 PM: Adding info for ide:0.0 PM: Adding info for ide:0.1 hdc: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive PM: Adding info for No Bus:ide1 ide1 at 0x170-0x177,0x376 on irq 15 PM: Adding info for ide:1.0 hda: max request size: 128KiB hda: 160086528 sectors (81964 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(133) hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 > hdb: max request size: 128KiB hdb: 60030432 sectors (30735 MB) w/2048KiB Cache, CHS=59554/16/63, UDMA(100) hdb: hdb1 hdc: ATAPI 50X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12 ide-floppy driver 0.99.newide PM: Adding info for No Bus:ide-scsi ppa: Version 2.07 (for Linux 2.4.x) ppa: Found device at ID 6, Attempting to use EPP 32 bit ppa: Communication established with ID 6 using EPP 32 bit scsi0 : Iomega VPI0 (ppa) interface PM: Adding info for No Bus:host0 Vendor: IOMEGA Model: ZIP 100 Rev: D.09 Type: Direct-Access ANSI SCSI revision: 02 PM: Adding info for scsi:0:0:6:0 Attached scsi removable disk sda at scsi0, channel 0, id 6, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 6, lun 0, type 0 ehci_hcd: block sizes: qh 128 qtd 96 itd 128 sitd 64 ehci_hcd 0000:00:03.3: EHCI Host Controller ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024 ehci_hcd 0000:00:03.3: capability 0001 at 70 ehci_hcd 0000:00:03.3: irq 23, pci mem e081c000 ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:03.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024 RUN ehci_hcd 0000:00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13 ehci_hcd 0000:00:03.3: root hub device address 1 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.0-test4 ehci_hcd usb usb1: SerialNumber: 0000:00:03.3 drivers/usb/core/usb.c: usb_hotplug PM: Adding info for usb:usb1 usb usb1: usb_new_device - registering interface 1-0:0 drivers/usb/core/usb.c: usb_hotplug hub 1-0:0: usb_probe_interface hub 1-0:0: usb_probe_interface - got id hub 1-0:0: USB hub found hub 1-0:0: 6 ports detected hub 1-0:0: standalone hub hub 1-0:0: ganged power switching hub 1-0:0: individual port over-current protection hub 1-0:0: Single TT hub 1-0:0: TT requires at most 8 FS bit times hub 1-0:0: Port indicators are not supported hub 1-0:0: power on to power good time: 0ms hub 1-0:0: hub controller current requirement: 0mA hub 1-0:0: local power source is good hub 1-0:0: no over-current condition exists hub 1-0:0: enabling power on all ports PM: Adding info for usb:1-0:0 ohci-hcd: 2003 Feb 24 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci-hcd: block sizes: ed 64 td 64 pci_irq-0299 [18] acpi_pci_irq_derive : Unable to derive IRQ for device 0000:00:03.0 ACPI: No IRQ known for interrupt pin A of device 0000:00:03.0 ohci-hcd 0000:00:03.0: OHCI Host Controller ohci-hcd 0000:00:03.0: irq 9, pci mem e081e000 ohci-hcd 0000:00:03.0: new USB bus registered, assigned bus number 2 ohci-hcd 0000:00:03.0: reset, control = 0x0 ohci-hcd 0000:00:03.0: root hub device address 1 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.0-test4 ohci-hcd usb usb2: SerialNumber: 0000:00:03.0 drivers/usb/core/usb.c: usb_hotplug PM: Adding info for usb:usb2 usb usb2: usb_new_device - registering interface 2-0:0 drivers/usb/core/usb.c: usb_hotplug hub 2-0:0: usb_probe_interface hub 2-0:0: usb_probe_interface - got id hub 2-0:0: USB hub found hub 2-0:0: 2 ports detected hub 2-0:0: standalone hub hub 2-0:0: ganged power switching hub 2-0:0: global over-current protection hub 2-0:0: Port indicators are not supported hub 2-0:0: power on to power good time: 2ms hub 2-0:0: hub controller current requirement: 0mA hub 2-0:0: local power source is good hub 2-0:0: no over-current condition exists hub 2-0:0: enabling power on all ports PM: Adding info for usb:2-0:0 ohci-hcd 0000:00:03.0: created debug files ohci-hcd 0000:00:03.0: OHCI controller state ohci-hcd 0000:00:03.0: OHCI 1.0, with legacy support registers ohci-hcd 0000:00:03.0: control 0x08f HCFS=operational IE PLE CBSR=3 ohci-hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0 ohci-hcd 0000:00:03.0: intrstatus 0x00000004 SF ohci-hcd 0000:00:03.0: intrenable 0x80000002 MIE WDH ohci-hcd 0000:00:03.0: hcca frame #0011 ohci-hcd 0000:00:03.0: roothub.a 01000202 POTPGT=1 NPS NDP=2 ohci-hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000 ohci-hcd 0000:00:03.0: roothub.status 00000000 ohci-hcd 0000:00:03.0: roothub.portstatus [0] 0x00000100 PPS ohci-hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS ohci-hcd 0000:00:03.1: OHCI Host Controller ohci-hcd 0000:00:03.1: irq 21, pci mem e0820000 ohci-hcd 0000:00:03.1: new USB bus registered, assigned bus number 3 ohci-hcd 0000:00:03.1: reset, control = 0x0 ohci-hcd 0000:00:03.1: root hub device address 1 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.0-test4 ohci-hcd usb usb3: SerialNumber: 0000:00:03.1 drivers/usb/core/usb.c: usb_hotplug PM: Adding info for usb:usb3 usb usb3: usb_new_device - registering interface 3-0:0 drivers/usb/core/usb.c: usb_hotplug hub 3-0:0: usb_probe_interface hub 3-0:0: usb_probe_interface - got id hub 3-0:0: USB hub found hub 3-0:0: 2 ports detected hub 3-0:0: standalone hub hub 3-0:0: ganged power switching hub 3-0:0: global over-current protection hub 3-0:0: Port indicators are not supported hub 3-0:0: power on to power good time: 2ms hub 3-0:0: hub controller current requirement: 0mA hub 3-0:0: local power source is good hub 3-0:0: no over-current condition exists hub 3-0:0: enabling power on all ports PM: Adding info for usb:3-0:0 ohci-hcd 0000:00:03.1: created debug files ohci-hcd 0000:00:03.1: OHCI controller state ohci-hcd 0000:00:03.1: OHCI 1.0, with legacy support registers ohci-hcd 0000:00:03.1: control 0x08f HCFS=operational IE PLE CBSR=3 ohci-hcd 0000:00:03.1: cmdstatus 0x00000 SOC=0 ohci-hcd 0000:00:03.1: intrstatus 0x00000004 SF ohci-hcd 0000:00:03.1: intrenable 0x80000002 MIE WDH ohci-hcd 0000:00:03.1: hcca frame #0011 ohci-hcd 0000:00:03.1: roothub.a 01000202 POTPGT=1 NPS NDP=2 ohci-hcd 0000:00:03.1: roothub.b 00000000 PPCM=0000 DR=0000 ohci-hcd 0000:00:03.1: roothub.status 00000000 ohci-hcd 0000:00:03.1: roothub.portstatus [0] 0x00000100 PPS ohci-hcd 0000:00:03.1: roothub.portstatus [1] 0x00000100 PPS ohci-hcd 0000:00:03.2: OHCI Host Controller ohci-hcd 0000:00:03.2: irq 22, pci mem e0822000 ohci-hcd 0000:00:03.2: new USB bus registered, assigned bus number 4 ohci-hcd 0000:00:03.2: reset, control = 0x0 ohci-hcd 0000:00:03.2: root hub device address 1 usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.0-test4 ohci-hcd usb usb4: SerialNumber: 0000:00:03.2 drivers/usb/core/usb.c: usb_hotplug PM: Adding info for usb:usb4 usb usb4: usb_new_device - registering interface 4-0:0 drivers/usb/core/usb.c: usb_hotplug hub 4-0:0: usb_probe_interface hub 4-0:0: usb_probe_interface - got id hub 4-0:0: USB hub found hub 4-0:0: 2 ports detected hub 4-0:0: standalone hub hub 4-0:0: ganged power switching hub 4-0:0: global over-current protection hub 4-0:0: Port indicators are not supported hub 4-0:0: power on to power good time: 2ms hub 4-0:0: hub controller current requirement: 0mA hub 4-0:0: local power source is good hub 4-0:0: no over-current condition exists hub 4-0:0: enabling power on all ports PM: Adding info for usb:4-0:0 ohci-hcd 0000:00:03.2: created debug files ohci-hcd 0000:00:03.2: OHCI controller state ohci-hcd 0000:00:03.2: OHCI 1.0, with legacy support registers ohci-hcd 0000:00:03.2: control 0x08f HCFS=operational IE PLE CBSR=3 ohci-hcd 0000:00:03.2: cmdstatus 0x00000 SOC=0 ohci-hcd 0000:00:03.2: intrstatus 0x00000004 SF ohci-hcd 0000:00:03.2: intrenable 0x80000002 MIE WDH ohci-hcd 0000:00:03.2: hcca frame #0011 ohci-hcd 0000:00:03.2: roothub.a 01000202 POTPGT=1 NPS NDP=2 ohci-hcd 0000:00:03.2: roothub.b 00000000 PPCM=0000 DR=0000 ohci-hcd 0000:00:03.2: roothub.status 00000000 ohci-hcd 0000:00:03.2: roothub.portstatus [0] 0x00000100 PPS ohci-hcd 0000:00:03.2: roothub.portstatus [1] 0x00000100 PPS drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 drivers/usb/core/usb.c: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver drivers/usb/core/usb.c: registered new driver usbscanner drivers/usb/image/scanner.c: 0.4.14:USB Scanner Driver mice: PS/2 mouse device common for all mice input: PC Speaker input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 LLC 2.0 by Procom, 1997, Arnaldo C. Melo, 2001, 2002 NET 4.0 IEEE 802.2 extended support NET4.0 IEEE 802.2 BSD sockets, Jay Schulist, 2001, Arnaldo C. Melo, 2002-2003 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 65536) Linux IP multicast router 0.06 plus PIM-SM ip_conntrack version 2.1 (4095 buckets, 32760 max) - 300 bytes per conntrack ehci_hcd 0000:00:03.3: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT hub 1-0:0: port 1, status 501, change 1, 480 Mb/s ip_tables: (C) 2000-2002 Netfilter core team Initializing IPsec netlink socket NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver ip6_tables: (C) 2000-2002 Netfilter core team RAMDISK: Compressed image found at block 0 Freeing initrd memory: 219k freed VFS: Mounted root (ext2 filesystem). hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x501 ehci_hcd 0000:00:03.3: port 1 low speed --> companion kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ehci_hcd 0000:00:03.3: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC ehci_hcd 0000:00:03.3: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT hub 1-0:0: port 3, status 501, change 1, 480 Mb/s Freeing unused kernel memory: 164k freed hub 1-0:0: debounce: port 3: delay 100ms stable 4 status 0x501 ehci_hcd 0000:00:03.3: port 3 full speed --> companion ehci_hcd 0000:00:03.3: GetStatus port 3 status 003001 POWER OWNER sig=se0 CONNECT ohci-hcd 0000:00:03.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS hub 2-0:0: port 1, status 301, change 1, 1.5 Mb/s hub 2-0:0: debounce: port 1: delay 100ms stable 4 status 0x301 ohci-hcd 0000:00:03.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS hub 2-0:0: new USB device on port 1, assigned address 2 irq 20: nobody cared! Call Trace: [] __report_bad_irq+0x2b/0x8c [] acpi_irq+0xf/0x1a [] note_interrupt+0x69/0x99 [] do_IRQ+0x14a/0x176 [] default_idle+0x0/0x2c [] _stext+0x0/0x61 [] common_interrupt+0x18/0x20 [] default_idle+0x0/0x2c [] _stext+0x0/0x61 [] default_idle+0x27/0x2c [] cpu_idle+0x31/0x3a [] start_kernel+0x17b/0x1a0 [] unknown_bootoption+0x0/0xfa handlers: [] (acpi_irq+0x0/0x1a) Disabling IRQ #20 drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver EXT3 FS on hda2, internal journal Adding 1004020k swap on /dev/hda5. Priority:-1 extents:1 usb 2-1: control timeout on ep0out intel8x0: clocking to 48000 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected SiS 648 chipset agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xe0000000 kjournald starting. Commit interval 5 seconds EXT3 FS on hda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kudzu: numerical sysctl 1 23 is obsolete. ohci1394: $Rev: 1023 $ Ben Collins ohci1394_0: Unexpected PCI resource length of 1000! ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[de800000-de8007ff] Max Packet=[2048] PM: Adding info for ieee1394:fw-host0 PM: Adding info for ieee1394:00e018000006d3df ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e018000006d3df] Disabled Privacy Extensions on device c0423400(lo) sis900.c: v1.08.06 9/24/2002 eth0: Realtek RTL8201 PHY transceiver found at address 1. eth0: Using transceiver found at address 1 as default eth0: SiS 900 PCI Fast Ethernet at 0x9800, IRQ 19, 00:e0:18:9d:4f:d0. eth0: Media Link On 100mbps full-duplex Linux Tulip driver version 1.1.13 (May 11, 2002) eth1: ADMtek Comet rev 17 at 0x9400, 00:20:78:04:68:6F, IRQ 19. eth0: no IPv6 routers present drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic drivers/usb/core/usb.c: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0