* PATCH: ethtool support for forcedeth for 2.4.33-pre1
@ 2006-01-12 14:41 Christopher Lalancette
0 siblings, 0 replies; only message in thread
From: Christopher Lalancette @ 2006-01-12 14:41 UTC (permalink / raw)
To: linux-kernel
All,
The patch below adds improved ethtool support for forcedeth for
2.4.33-pre1. The patch was originally written against 2.4.21, but
applies to 2.4.33-pre1 as well. This patch adds support for get/set
settings, get regs, and nway rst.
Chris Lalancette
--- linux-2.4.21/drivers/net/forcedeth.c.v0.30 2006-01-11
16:28:20.557859000 -0500
+++ linux-2.4.21/drivers/net/forcedeth.c 2006-01-11
16:32:32.750417000 -0500
@@ -212,6 +212,7 @@
#define NVREG_LINKSPEED_10 1000
#define NVREG_LINKSPEED_100 100
#define NVREG_LINKSPEED_1000 50
+#define NVREG_LINKSPEED_MASK (0xFFF)
NvRegUnknownSetupReg5 = 0x130,
#define NVREG_UNKSETUP5_BIT31 (1<<31)
NvRegUnknownSetupReg3 = 0x13c,
@@ -443,6 +444,8 @@
int in_shutdown;
u32 linkspeed;
int duplex;
+ int autoneg;
+ int fixed_mode;
int phyaddr;
int wolenabled;
unsigned int phy_oui;
@@ -802,11 +805,238 @@
return 0;
}
+static int nv_update_linkspeed(struct net_device *dev);
+static int nv_get_settings(struct net_device *dev, struct ethtool_cmd
*ecmd)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ int adv;
+
+ spin_lock_irq(&np->lock);
+ ecmd->port = PORT_MII;
+ if (!netif_running(dev)) {
+ /* We do not track link speed / duplex setting if the
+ * interface is disabled. Force a link check */
+ nv_update_linkspeed(dev);
+ }
+ switch(np->linkspeed & (NVREG_LINKSPEED_MASK)) {
+ case NVREG_LINKSPEED_10:
+ ecmd->speed = SPEED_10;
+ break;
+ case NVREG_LINKSPEED_100:
+ ecmd->speed = SPEED_100;
+ break;
+ case NVREG_LINKSPEED_1000:
+ ecmd->speed = SPEED_1000;
+ break;
+ }
+ ecmd->duplex = DUPLEX_HALF;
+ if (np->duplex)
+ ecmd->duplex = DUPLEX_FULL;
+
+ ecmd->autoneg = np->autoneg;
+
+ ecmd->advertising = ADVERTISED_MII;
+ if (np->autoneg) {
+ ecmd->advertising |= ADVERTISED_Autoneg;
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ } else {
+ adv = np->fixed_mode;
+ }
+
+ if (adv & ADVERTISE_10HALF)
+ ecmd->advertising |= ADVERTISED_10baseT_Half;
+ if (adv & ADVERTISE_10FULL)
+ ecmd->advertising |= ADVERTISED_10baseT_Full;
+ if (adv & ADVERTISE_100HALF)
+ ecmd->advertising |= ADVERTISED_100baseT_Half;
+ if (adv & ADVERTISE_100FULL)
+ ecmd->advertising |= ADVERTISED_100baseT_Full;
+ if (np->autoneg && np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ if (adv & ADVERTISE_1000FULL)
+ ecmd->advertising |= ADVERTISED_1000baseT_Full;
+ }
+
+ ecmd->supported = (SUPPORTED_Autoneg |
+ SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
+ SUPPORTED_MII);
+ if (np->gigabit == PHY_GIGABIT)
+ ecmd->supported |= SUPPORTED_1000baseT_Full;
+
+ ecmd->phy_address = np->phyaddr;
+ ecmd->transceiver = XCVR_EXTERNAL;
+
+ /* ignore maxtxpkt, maxrxpkt for now */
+ spin_unlock_irq(&np->lock);
+ return 0;
+}
+
+static void nv_linkchange(struct net_device *dev);
+static int nv_set_settings(struct net_device *dev, struct ethtool_cmd
*ecmd)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+
+ if (ecmd->port != PORT_MII)
+ return -EINVAL;
+ if (ecmd->transceiver != XCVR_EXTERNAL)
+ return -EINVAL;
+ if (ecmd->phy_address != np->phyaddr) {
+ /* TODO: support switching between multiple phys. Should be
+ * trivial, but not enabled due to lack of test hardware. */
+ return -EINVAL;
+ }
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ u32 mask;
+
+ mask = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
+ ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full;
+ if (np->gigabit == PHY_GIGABIT)
+ mask |= ADVERTISED_1000baseT_Full;
+
+ if ((ecmd->advertising & mask) == 0)
+ return -EINVAL;
+
+ } else if (ecmd->autoneg == AUTONEG_DISABLE) {
+ /* Note: autonegotiation disable, speed 1000 intentionally
+ * forbidden - noone should need that. */
+
+ if (ecmd->speed != SPEED_10 && ecmd->speed != SPEED_100)
+ return -EINVAL;
+ if (ecmd->duplex != DUPLEX_HALF && ecmd->duplex != DUPLEX_FULL)
+ return -EINVAL;
+ } else {
+ return -EINVAL;
+ }
+
+ spin_lock_irq(&np->lock);
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ int adv, bmcr;
+
+ np->autoneg = 1;
+
+ /* advertise only what has been requested */
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
+ if (ecmd->advertising & ADVERTISED_10baseT_Half)
+ adv |= ADVERTISE_10HALF;
+ if (ecmd->advertising & ADVERTISED_10baseT_Full)
+ adv |= ADVERTISE_10FULL;
+ if (ecmd->advertising & ADVERTISED_100baseT_Half)
+ adv |= ADVERTISE_100HALF;
+ if (ecmd->advertising & ADVERTISED_100baseT_Full)
+ adv |= ADVERTISE_100FULL;
+ mii_rw(dev, np->phyaddr, MII_ADVERTISE, adv);
+
+ if (np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ adv &= ~ADVERTISE_1000FULL;
+ if (ecmd->advertising & ADVERTISED_1000baseT_Full)
+ adv |= ADVERTISE_1000FULL;
+ mii_rw(dev, np->phyaddr, MII_1000BT_CR, adv);
+ }
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ } else {
+ int adv, bmcr;
+
+ np->autoneg = 0;
+
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
+ if (ecmd->speed == SPEED_10 && ecmd->duplex == DUPLEX_HALF)
+ adv |= ADVERTISE_10HALF;
+ if (ecmd->speed == SPEED_10 && ecmd->duplex == DUPLEX_FULL)
+ adv |= ADVERTISE_10FULL;
+ if (ecmd->speed == SPEED_100 && ecmd->duplex == DUPLEX_HALF)
+ adv |= ADVERTISE_100HALF;
+ if (ecmd->speed == SPEED_100 && ecmd->duplex == DUPLEX_FULL)
+ adv |= ADVERTISE_100FULL;
+ mii_rw(dev, np->phyaddr, MII_ADVERTISE, adv);
+ np->fixed_mode = adv;
+
+ if (np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ adv &= ~ADVERTISE_1000FULL;
+ mii_rw(dev, np->phyaddr, MII_1000BT_CR, adv);
+ }
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= ~(BMCR_ANENABLE|BMCR_SPEED100|BMCR_FULLDPLX);
+ if (adv & (ADVERTISE_10FULL|ADVERTISE_100FULL))
+ bmcr |= BMCR_FULLDPLX;
+ if (adv & (ADVERTISE_100HALF|ADVERTISE_100FULL))
+ bmcr |= BMCR_SPEED100;
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ if (netif_running(dev)) {
+ /* Wait a bit and then reconfigure the nic. */
+ udelay(10);
+ nv_linkchange(dev);
+ }
+ }
+ spin_unlock_irq(&np->lock);
+
+ return 0;
+}
+
+#define FORCEDETH_REGS_VER 1
+#define FORCEDETH_REGS_SIZE 0x400 /* 256 32-bit registers */
+
+static int nv_get_regs_len(struct net_device *dev)
+{
+ return FORCEDETH_REGS_SIZE;
+}
+
+static void nv_get_regs(struct net_device *dev, struct ethtool_regs
*regs, void *buf)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ u8 *base = get_hwbase(dev);
+ u32 *rbuf = buf;
+ int i;
+
+ regs->version = FORCEDETH_REGS_VER;
+ spin_lock_irq(&np->lock);
+ for (i=0;i<FORCEDETH_REGS_SIZE/sizeof(u32);i++)
+ rbuf[i] = readl(base + i*sizeof(u32));
+ spin_unlock_irq(&np->lock);
+}
+
+static int nv_nway_reset(struct net_device *dev)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ int ret;
+
+ spin_lock_irq(&np->lock);
+ if (np->autoneg) {
+ int bmcr;
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ ret = 0;
+ } else {
+ ret = -EINVAL;
+ }
+ spin_unlock_irq(&np->lock);
+
+ return ret;
+}
+
static struct ethtool_ops ops = {
.get_drvinfo = nv_get_drvinfo,
.get_link = ethtool_op_get_link,
.get_wol = nv_get_wol,
.set_wol = nv_set_wol,
+ .get_settings = nv_get_settings,
+ .set_settings = nv_set_settings,
+ .get_regs_len = nv_get_regs_len,
+ .get_regs = nv_get_regs,
+ .nway_reset = nv_nway_reset,
};
/*
@@ -1286,6 +1516,25 @@
goto set_speed;
}
+ if (np->autoneg == 0) {
+ dprintk(KERN_DEBUG "%s: nv_update_linkspeed: autoneg off, PHY
set to 0x%04x.\n",
+ dev->name, np->fixed_mode);
+ if (np->fixed_mode & LPA_100FULL) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_100;
+ newdup = 1;
+ } else if (np->fixed_mode & LPA_100HALF) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_100;
+ newdup = 0;
+ } else if (np->fixed_mode & LPA_10FULL) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ newdup = 1;
+ } else {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ newdup = 0;
+ }
+ retval = 1;
+ goto set_speed;
+ }
/* check auto negotiation is complete */
if (!(mii_status & BMSR_ANEGCOMPLETE)) {
/* still in autonegotiation - configure nic for 10 MBit HD and
wait. */
@@ -1362,9 +1611,9 @@
phyreg &= ~(PHY_HALF|PHY_100|PHY_1000);
if (np->duplex == 0)
phyreg |= PHY_HALF;
- if ((np->linkspeed & 0xFFF) == NVREG_LINKSPEED_100)
+ if ((np->linkspeed & NVREG_LINKSPEED_MASK) == NVREG_LINKSPEED_100)
phyreg |= PHY_100;
- else if ((np->linkspeed & 0xFFF) == NVREG_LINKSPEED_1000)
+ else if ((np->linkspeed & NVREG_LINKSPEED_MASK) ==
NVREG_LINKSPEED_1000)
phyreg |= PHY_1000;
writel(phyreg, base + NvRegPhyInterface);
@@ -1865,6 +2114,10 @@
phy_init(dev);
}
+ np->linkspeed = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ np->duplex = 0;
+ np->autoneg = 1;
+
err = register_netdev(dev);
if (err) {
printk(KERN_INFO "forcedeth: unable to register netdev: %d\n",
err);
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2006-01-12 14:41 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2006-01-12 14:41 PATCH: ethtool support for forcedeth for 2.4.33-pre1 Christopher Lalancette
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).