[RFC 00/13] [net-next] drivers/net/Space.c cleanup

[RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

I discovered that there are still a couple of drivers that rely on
beiong statically initialized from drivers/net/Space.c the way
we did in the last century. As it turns out, there are a couple
of simplifications that can be made here, as well as some minor
bugfixes.

There are four classes of drivers that use this:

- most 10mbit ISA bus ethernet drivers (and one 100mbit one)
- both ISA localtalk drivers
- several m68k ethernet drivers
- one obsolete WAN driver

I found that the drivers using in arch/m68k/ don't actually benefit
from being probed this way as they do not rely on the netdev= command
line arguments, they have simply never been changed to work like a
modern driver.

I had previously sent a patch to remove the sbni/granch driver, and
there were no objections to this patch but forgot to resend it after
some discussion about another patch in the same series.

For the ISA drivers, there is usually no way to probe multiple devices
at boot time other than the netdev= arguments, so all that logic is left
in place for the moment, but centralized in a single file that only gets
included in the kernel build if one or more of the drivers are built-in.

I'm also changing the old-style init_module() functions in these drivers
to static functions with a module_init() annotation, to more closely
resemble modern drivers. There are only a few users of the init_module()
interface remaining, and removing that would likely allow some cleanups
in the module loader code.

There are a couple of possible follow-ups:

* Most of ISA drivers could be trivially converted to use the module_init()
  entry point, which would slightly change the command line syntax and
  still support a single device of that type, but not more than one. We
  could decide that this is fine, as few users remain that have any of
  these devices, let alone more than one.

* Alternatively, the fact that the ISA drivers have never been cleaned
  up can be seen as an indication that there isn't really much remaining
  interest in them. We could move them to drivers/staging along with the
  consolidated contents of drivers/net/Space.c and see if anyone still
  uses them and eventually remove the ones that nobody has.
  I can see that Paul Gortmaker removed a number of less common ISA
  ethernet drivers in 2013, but at the time left these because they
  were possibly still relevant.

* If we end up moving the cops localtalk driver to staging, support
  for localtalk devices (though probably not appletalk over ethernet)
  can arguably meet the same fate.

If someone wants to work on those follow-ups or thinks they are a
good idea, let me know, otherwise I'd leave it at this cleanup.

       Arnd

Arnd Bergmann (13):
  [net-next] bcmgenet: remove call to netdev_boot_setup_check
  [net-next] natsemi: sonic: stop calling netdev_boot_setup_check
  [net-next] appletalk: ltpc: remove static probing
  [net-next] 3c509: stop calling netdev_boot_setup_check
  [net-next] cs89x0: rework driver configuration
  [net-next] m68k: remove legacy probing
  [net-next] move netdev_boot_setup into Space.c
  [net-next] make legacy ISA probe optional
  [net-next] wan: remove stale Kconfig entries
  [net-next] wan: remove sbni/granch driver
  [net-next] wan: hostess_sv11: use module_init/module_exit helpers
  [net-next] ethernet: isa: convert to module_init/module_exit
  [net-next] 8390: xsurf100: avoid including lib8390.c

 .../admin-guide/kernel-parameters.txt         |    2 -
 drivers/net/Kconfig                           |    7 +
 drivers/net/Makefile                          |    3 +-
 drivers/net/Space.c                           |  178 +-
 drivers/net/appletalk/Kconfig                 |    4 +-
 drivers/net/appletalk/ltpc.c                  |    7 +-
 drivers/net/ethernet/3com/3c509.c             |    3 -
 drivers/net/ethernet/3com/3c515.c             |    3 +-
 drivers/net/ethernet/3com/Kconfig             |    1 +
 drivers/net/ethernet/8390/Kconfig             |    3 +
 drivers/net/ethernet/8390/Makefile            |    2 +-
 drivers/net/ethernet/8390/apne.c              |   11 +-
 drivers/net/ethernet/8390/ne.c                |    5 +-
 drivers/net/ethernet/8390/smc-ultra.c         |    9 +-
 drivers/net/ethernet/8390/wd.c                |    7 +-
 drivers/net/ethernet/8390/xsurf100.c          |    7 +-
 drivers/net/ethernet/amd/Kconfig              |    2 +
 drivers/net/ethernet/amd/atarilance.c         |   11 +-
 drivers/net/ethernet/amd/lance.c              |    6 +-
 drivers/net/ethernet/amd/mvme147.c            |   16 +-
 drivers/net/ethernet/amd/ni65.c               |    6 +-
 drivers/net/ethernet/amd/sun3lance.c          |   19 +-
 .../net/ethernet/broadcom/genet/bcmgenet.c    |    2 -
 drivers/net/ethernet/cirrus/Kconfig           |   27 +-
 drivers/net/ethernet/cirrus/cs89x0.c          |   31 +-
 drivers/net/ethernet/i825xx/82596.c           |   24 +-
 drivers/net/ethernet/i825xx/sun3_82586.c      |   17 +-
 drivers/net/ethernet/natsemi/jazzsonic.c      |    2 -
 drivers/net/ethernet/natsemi/xtsonic.c        |    1 -
 drivers/net/ethernet/smsc/Kconfig             |    1 +
 drivers/net/ethernet/smsc/smc9194.c           |    6 +-
 drivers/net/wan/Kconfig                       |   51 -
 drivers/net/wan/Makefile                      |    1 -
 drivers/net/wan/hostess_sv11.c                |    6 +-
 drivers/net/wan/sbni.c                        | 1638 -----------------
 drivers/net/wan/sbni.h                        |  147 --
 include/linux/netdevice.h                     |   13 -
 include/net/Space.h                           |   10 -
 net/core/dev.c                                |  125 --
 net/ethernet/eth.c                            |    2 -
 40 files changed, 259 insertions(+), 2157 deletions(-)
 delete mode 100644 drivers/net/wan/sbni.c
 delete mode 100644 drivers/net/wan/sbni.h

-- 
2.29.2

Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Doug Berger <opendmb@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com

[RFC 01/13] [net-next] bcmgenet: remove call to netdev_boot_setup_check

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

The driver has never used the netdev->{irq,base_addr,mem_start}
members, so this call is completely unnecessary.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 2 --
 1 file changed, 2 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index fcca023f22e5..b52910f141dc 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -3972,8 +3972,6 @@ static int bcmgenet_probe(struct platform_device *pdev)
 	 */
 	dev->needed_headroom += 64;
 
-	netdev_boot_setup_check(dev);
-
 	priv->dev = dev;
 	priv->pdev = pdev;
 
-- 
2.29.2

[RFC 02/13] [net-next] natsemi: sonic: stop calling netdev_boot_setup_check

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

The data from the kernel command line is no longer used since the
probe function gets it from the platform device resources instead.

The jazz version was changed to be like this in 2007, the xtensa
version apparently copied the code from there.

Fixes: ed9f0e0bf3ce ("remove setup of platform device from jazzsonic.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/ethernet/natsemi/jazzsonic.c | 2 --
 drivers/net/ethernet/natsemi/xtsonic.c   | 1 -
 2 files changed, 3 deletions(-)

diff --git a/drivers/net/ethernet/natsemi/jazzsonic.c b/drivers/net/ethernet/natsemi/jazzsonic.c
index ce3eca5d152b..d74a80f010c5 100644
--- a/drivers/net/ethernet/natsemi/jazzsonic.c
+++ b/drivers/net/ethernet/natsemi/jazzsonic.c
@@ -193,8 +193,6 @@ static int jazz_sonic_probe(struct platform_device *pdev)
 	SET_NETDEV_DEV(dev, &pdev->dev);
 	platform_set_drvdata(pdev, dev);
 
-	netdev_boot_setup_check(dev);
-
 	dev->base_addr = res->start;
 	dev->irq = platform_get_irq(pdev, 0);
 	err = sonic_probe1(dev);
diff --git a/drivers/net/ethernet/natsemi/xtsonic.c b/drivers/net/ethernet/natsemi/xtsonic.c
index 28d9e98db81a..ca4686094701 100644
--- a/drivers/net/ethernet/natsemi/xtsonic.c
+++ b/drivers/net/ethernet/natsemi/xtsonic.c
@@ -215,7 +215,6 @@ int xtsonic_probe(struct platform_device *pdev)
 	lp->device = &pdev->dev;
 	platform_set_drvdata(pdev, dev);
 	SET_NETDEV_DEV(dev, &pdev->dev);
-	netdev_boot_setup_check(dev);
 
 	dev->base_addr = resmem->start;
 	dev->irq = resirq->start;
-- 
2.29.2

[RFC 03/13] [net-next] appletalk: ltpc: remove static probing

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

This driver never relies on the netdev_boot_setup_check()
to get its configuration, so it can just as well do its
own probing all the time.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/Space.c          | 3 ---
 drivers/net/appletalk/ltpc.c | 7 ++-----
 include/net/Space.h          | 1 -
 3 files changed, 2 insertions(+), 9 deletions(-)

diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index df79e7370bcc..9196a26615cc 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -142,9 +142,6 @@ static int __init net_olddevs_init(void)
 	cops_probe(1);
 	cops_probe(2);
 #endif
-#ifdef CONFIG_LTPC
-	ltpc_probe();
-#endif
 
 	return 0;
 }
diff --git a/drivers/net/appletalk/ltpc.c b/drivers/net/appletalk/ltpc.c
index c6f73aa3700c..9e7d3c686561 100644
--- a/drivers/net/appletalk/ltpc.c
+++ b/drivers/net/appletalk/ltpc.c
@@ -1013,7 +1013,7 @@ static const struct net_device_ops ltpc_netdev = {
 	.ndo_set_rx_mode	= set_multicast_list,
 };
 
-struct net_device * __init ltpc_probe(void)
+static struct net_device * __init ltpc_probe(void)
 {
 	struct net_device *dev;
 	int err = -ENOMEM;
@@ -1219,12 +1219,10 @@ static int __init ltpc_setup(char *str)
 }
 
 __setup("ltpc=", ltpc_setup);
-#endif /* MODULE */
+#endif
 
 static struct net_device *dev_ltpc;
 
-#ifdef MODULE
-
 MODULE_LICENSE("GPL");
 module_param(debug, int, 0);
 module_param_hw(io, int, ioport, 0);
@@ -1242,7 +1240,6 @@ static int __init ltpc_module_init(void)
 	return PTR_ERR_OR_ZERO(dev_ltpc);
 }
 module_init(ltpc_module_init);
-#endif
 
 static void __exit ltpc_cleanup(void)
 {
diff --git a/include/net/Space.h b/include/net/Space.h
index 9cce0d80d37a..e30e7a70ea99 100644
--- a/include/net/Space.h
+++ b/include/net/Space.h
@@ -21,7 +21,6 @@ struct net_device *mvme147lance_probe(int unit);
 struct net_device *tc515_probe(int unit);
 struct net_device *lance_probe(int unit);
 struct net_device *cops_probe(int unit);
-struct net_device *ltpc_probe(void);
 
 /* Fibre Channel adapters */
 int iph5526_probe(struct net_device *dev);
-- 
2.29.2

[RFC 04/13] [net-next] 3c509: stop calling netdev_boot_setup_check

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

This driver never uses the information returned by
netdev_boot_setup_check, and is not called by the boot-time probing from
driver/net/Space.c, so just remove these stale references.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/ethernet/3com/3c509.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/drivers/net/ethernet/3com/3c509.c b/drivers/net/ethernet/3com/3c509.c
index 96cc5fc36eb5..7fd2d322f2bb 100644
--- a/drivers/net/ethernet/3com/3c509.c
+++ b/drivers/net/ethernet/3com/3c509.c
@@ -302,7 +302,6 @@ static int el3_isa_match(struct device *pdev, unsigned int ndev)
 		return -ENOMEM;
 
 	SET_NETDEV_DEV(dev, pdev);
-	netdev_boot_setup_check(dev);
 
 	if (!request_region(ioaddr, EL3_IO_EXTENT, "3c509-isa")) {
 		free_netdev(dev);
@@ -421,7 +420,6 @@ static int el3_pnp_probe(struct pnp_dev *pdev, const struct pnp_device_id *id)
 		return -ENOMEM;
 	}
 	SET_NETDEV_DEV(dev, &pdev->dev);
-	netdev_boot_setup_check(dev);
 
 	el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_PNP);
 	pnp_set_drvdata(pdev, dev);
@@ -588,7 +586,6 @@ static int el3_eisa_probe(struct device *device)
 	}
 
 	SET_NETDEV_DEV(dev, device);
-	netdev_boot_setup_check(dev);
 
 	el3_dev_fill(dev, phys_addr, ioaddr, irq, if_port, EL3_EISA);
 	eisa_set_drvdata (edev, dev);
-- 
2.29.2

[RFC 05/13] [net-next] cs89x0: rework driver configuration

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

There are two drivers in the cs89x0 file, with the CONFIG_CS89x0_PLATFORM
symbol deciding which one is getting built. This is somewhat confusing
and makes it more likely ton configure a driver that works nowhere.

Split up the Kconfig option into separate ISA and PLATFORM drivers,
with the ISA symbol explicitly connecting to the static probing in
drivers/net/Space.c

The two drivers are still mutually incompatible at compile time,
which could be lifted by splitting them into multiple files,
but in practice this will make no difference.

The platform driver can now be enabled for compile-testing on
non-ARM machines.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/Space.c                  |  4 +---
 drivers/net/ethernet/cirrus/Kconfig  | 26 ++++++++++++++++----------
 drivers/net/ethernet/cirrus/cs89x0.c | 24 +++++++++++-------------
 3 files changed, 28 insertions(+), 26 deletions(-)

diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index 9196a26615cc..9f573f7ded3c 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -77,11 +77,9 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_SMC9194
 	{smc_init, 0},
 #endif
-#ifdef CONFIG_CS89x0
-#ifndef CONFIG_CS89x0_PLATFORM
+#ifdef CONFIG_CS89x0_ISA
 	{cs89x0_probe, 0},
 #endif
-#endif
 #if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET)	/* Intel */
 	{i82596_probe, 0},					/* I82596 */
 #endif
diff --git a/drivers/net/ethernet/cirrus/Kconfig b/drivers/net/ethernet/cirrus/Kconfig
index d8af9e64dd1e..7141340a8b0e 100644
--- a/drivers/net/ethernet/cirrus/Kconfig
+++ b/drivers/net/ethernet/cirrus/Kconfig
@@ -6,7 +6,7 @@
 config NET_VENDOR_CIRRUS
 	bool "Cirrus devices"
 	default y
-	depends on ISA || EISA || ARM || MAC
+	depends on ISA || EISA || ARM || MAC || COMPILE_TEST
 	help
 	  If you have a network (Ethernet) card belonging to this class, say Y.
 
@@ -18,9 +18,15 @@ config NET_VENDOR_CIRRUS
 if NET_VENDOR_CIRRUS
 
 config CS89x0
-	tristate "CS89x0 support"
-	depends on ISA || EISA || ARM
+	tristate
+
+config CS89x0_ISA
+	tristate "CS89x0 ISA driver support"
+	depends on HAS_IOPORT_MAP
+	depends on ISA
 	depends on !PPC32
+	depends on CS89x0_PLATFORM=n
+	select CS89x0
 	help
 	  Support for CS89x0 chipset based Ethernet cards. If you have a
 	  network (Ethernet) card of this type, say Y and read the file
@@ -30,15 +36,15 @@ config CS89x0
 	  will be called cs89x0.
 
 config CS89x0_PLATFORM
-	bool "CS89x0 platform driver support" if HAS_IOPORT_MAP
-	default !HAS_IOPORT_MAP
-	depends on CS89x0
+	tristate "CS89x0 platform driver support"
+	depends on ARM || COMPILE_TEST
+	select CS89x0
 	help
-	  Say Y to compile the cs89x0 driver as a platform driver. This
-	  makes this driver suitable for use on certain evaluation boards
-	  such as the iMX21ADS.
+	  Say Y to compile the cs89x0 platform driver. This makes this driver
+	  suitable for use on certain evaluation boards such as the iMX21ADS.
 
-	  If you are unsure, say N.
+	  To compile this driver as a module, choose M here. The module
+	  will be called cs89x0.
 
 config EP93XX_ETH
 	tristate "EP93xx Ethernet support"
diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c
index 33ace3307059..3b08cd943b7b 100644
--- a/drivers/net/ethernet/cirrus/cs89x0.c
+++ b/drivers/net/ethernet/cirrus/cs89x0.c
@@ -104,7 +104,7 @@ static char version[] __initdata =
  * them to system IRQ numbers. This mapping is card specific and is set to
  * the configuration of the Cirrus Eval board for this chip.
  */
-#ifndef CONFIG_CS89x0_PLATFORM
+#if IS_ENABLED(CONFIG_CS89x0_ISA)
 static unsigned int netcard_portlist[] __used __initdata = {
 	0x300, 0x320, 0x340, 0x360, 0x200, 0x220, 0x240,
 	0x260, 0x280, 0x2a0, 0x2c0, 0x2e0, 0
@@ -292,7 +292,7 @@ write_irq(struct net_device *dev, int chip_type, int irq)
 	int i;
 
 	if (chip_type == CS8900) {
-#ifndef CONFIG_CS89x0_PLATFORM
+#if IS_ENABLED(CONFIG_CS89x0_ISA)
 		/* Search the mapping table for the corresponding IRQ pin. */
 		for (i = 0; i != ARRAY_SIZE(cs8900_irq_map); i++)
 			if (cs8900_irq_map[i] == irq)
@@ -859,7 +859,7 @@ net_open(struct net_device *dev)
 			goto bad_out;
 		}
 	} else {
-#if !defined(CONFIG_CS89x0_PLATFORM)
+#if IS_ENABLED(CONFIG_CS89x0_ISA)
 		if (((1 << dev->irq) & lp->irq_map) == 0) {
 			pr_err("%s: IRQ %d is not in our map of allowable IRQs, which is %x\n",
 			       dev->name, dev->irq, lp->irq_map);
@@ -1523,7 +1523,7 @@ cs89x0_probe1(struct net_device *dev, void __iomem *ioaddr, int modular)
 			dev->irq = i;
 	} else {
 		i = lp->isa_config & INT_NO_MASK;
-#ifndef CONFIG_CS89x0_PLATFORM
+#if IS_ENABLED(CONFIG_CS89x0_ISA)
 		if (lp->chip_type == CS8900) {
 			/* Translate the IRQ using the IRQ mapping table. */
 			if (i >= ARRAY_SIZE(cs8900_irq_map))
@@ -1576,7 +1576,7 @@ cs89x0_probe1(struct net_device *dev, void __iomem *ioaddr, int modular)
 	return retval;
 }
 
-#ifndef CONFIG_CS89x0_PLATFORM
+#if IS_ENABLED(CONFIG_CS89x0_ISA)
 /*
  * This function converts the I/O port address used by the cs89x0_probe() and
  * init_module() functions to the I/O memory address used by the
@@ -1682,11 +1682,7 @@ struct net_device * __init cs89x0_probe(int unit)
 	pr_warn("no cs8900 or cs8920 detected.  Be sure to disable PnP with SETUP\n");
 	return ERR_PTR(err);
 }
-#endif
-#endif
-
-#if defined(MODULE) && !defined(CONFIG_CS89x0_PLATFORM)
-
+#else
 static struct net_device *dev_cs89x0;
 
 /* Support the 'debug' module parm even if we're compiled for non-debug to
@@ -1759,7 +1755,7 @@ MODULE_LICENSE("GPL");
 
 int __init init_module(void)
 {
-	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
+	struct net_device *dev;
 	struct net_local *lp;
 	int ret = 0;
 
@@ -1768,6 +1764,7 @@ int __init init_module(void)
 #else
 	debug = 0;
 #endif
+	dev = alloc_etherdev(sizeof(struct net_local));
 	if (!dev)
 		return -ENOMEM;
 
@@ -1838,9 +1835,10 @@ cleanup_module(void)
 	release_region(dev_cs89x0->base_addr, NETCARD_IO_EXTENT);
 	free_netdev(dev_cs89x0);
 }
-#endif /* MODULE && !CONFIG_CS89x0_PLATFORM */
+#endif /* MODULE */
+#endif /* CONFIG_CS89x0_ISA */
 
-#ifdef CONFIG_CS89x0_PLATFORM
+#if IS_ENABLED(CONFIG_CS89x0_PLATFORM)
 static int __init cs89x0_platform_probe(struct platform_device *pdev)
 {
 	struct net_device *dev = alloc_etherdev(sizeof(struct net_local));
-- 
2.29.2

[RFC 06/13] [net-next] m68k: remove legacy probing

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

There are six m68k specific drivers that use the legacy probe method
in drivers/net/Space.c. However, all of these only support a single
device, and they completely ignore the command line settings from
netdev_boot_setup_check, so there is really no point at all.

Aside from sun3_82586, these already have a module_init function that
can be used for built-in mode as well, simply by removing the #ifdef.

Note that the 82596 driver was previously used on ISA as well, but
that got dropped long ago.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/Space.c                      | 25 +-----------------------
 drivers/net/ethernet/8390/apne.c         | 11 ++---------
 drivers/net/ethernet/amd/atarilance.c    | 11 ++---------
 drivers/net/ethernet/amd/mvme147.c       | 16 ++++++---------
 drivers/net/ethernet/amd/sun3lance.c     | 19 ++++++------------
 drivers/net/ethernet/i825xx/82596.c      | 24 ++++++-----------------
 drivers/net/ethernet/i825xx/sun3_82586.c | 17 +++++++---------
 include/net/Space.h                      |  6 ------
 8 files changed, 30 insertions(+), 99 deletions(-)

diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index 9f573f7ded3c..a03559f23295 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -80,34 +80,12 @@ static struct devprobe2 isa_probes[] __initdata = {
 #ifdef CONFIG_CS89x0_ISA
 	{cs89x0_probe, 0},
 #endif
-#if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET)	/* Intel */
-	{i82596_probe, 0},					/* I82596 */
-#endif
 #ifdef CONFIG_NI65
 	{ni65_probe, 0},
 #endif
 	{NULL, 0},
 };
 
-static struct devprobe2 m68k_probes[] __initdata = {
-#ifdef CONFIG_ATARILANCE	/* Lance-based Atari ethernet boards */
-	{atarilance_probe, 0},
-#endif
-#ifdef CONFIG_SUN3LANCE         /* sun3 onboard Lance chip */
-	{sun3lance_probe, 0},
-#endif
-#ifdef CONFIG_SUN3_82586        /* sun3 onboard Intel 82586 chip */
-	{sun3_82586_probe, 0},
-#endif
-#ifdef CONFIG_APNE		/* A1200 PCMCIA NE2000 */
-	{apne_probe, 0},
-#endif
-#ifdef CONFIG_MVME147_NET	/* MVME147 internal Ethernet */
-	{mvme147lance_probe, 0},
-#endif
-	{NULL, 0},
-};
-
 /* Unified ethernet device probe, segmented per architecture and
  * per bus interface. This drives the legacy devices only for now.
  */
@@ -119,8 +97,7 @@ static void __init ethif_probe2(int unit)
 	if (base_addr == 1)
 		return;
 
-	(void)(probe_list2(unit, m68k_probes, base_addr == 0) &&
-		probe_list2(unit, isa_probes, base_addr == 0));
+	probe_list2(unit, isa_probes, base_addr == 0);
 }
 
 /*  Statically configured drivers -- order matters here. */
diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
index fe6c834c422e..da1ae37a9d73 100644
--- a/drivers/net/ethernet/8390/apne.c
+++ b/drivers/net/ethernet/8390/apne.c
@@ -75,7 +75,6 @@
 #define NESM_STOP_PG	0x80	/* Last page +1 of RX ring */
 
 
-struct net_device * __init apne_probe(int unit);
 static int apne_probe1(struct net_device *dev, int ioaddr);
 
 static void apne_reset_8390(struct net_device *dev);
@@ -120,7 +119,7 @@ static u32 apne_msg_enable;
 module_param_named(msg_enable, apne_msg_enable, uint, 0444);
 MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
 
-struct net_device * __init apne_probe(int unit)
+static struct net_device * __init apne_probe(void)
 {
 	struct net_device *dev;
 	struct ei_device *ei_local;
@@ -150,10 +149,6 @@ struct net_device * __init apne_probe(int unit)
 	dev = alloc_ei_netdev();
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
 	ei_local = netdev_priv(dev);
 	ei_local->msg_enable = apne_msg_enable;
 
@@ -554,12 +549,11 @@ static irqreturn_t apne_interrupt(int irq, void *dev_id)
     return IRQ_HANDLED;
 }
 
-#ifdef MODULE
 static struct net_device *apne_dev;
 
 static int __init apne_module_init(void)
 {
-	apne_dev = apne_probe(-1);
+	apne_dev = apne_probe();
 	return PTR_ERR_OR_ZERO(apne_dev);
 }
 
@@ -579,7 +573,6 @@ static void __exit apne_module_exit(void)
 }
 module_init(apne_module_init);
 module_exit(apne_module_exit);
-#endif
 
 static int init_pcmcia(void)
 {
diff --git a/drivers/net/ethernet/amd/atarilance.c b/drivers/net/ethernet/amd/atarilance.c
index c1eab916438f..83012a1ef3cf 100644
--- a/drivers/net/ethernet/amd/atarilance.c
+++ b/drivers/net/ethernet/amd/atarilance.c
@@ -367,7 +367,7 @@ static void *slow_memcpy( void *dst, const void *src, size_t len )
 }
 
 
-struct net_device * __init atarilance_probe(int unit)
+struct net_device * __init atarilance_probe(void)
 {
 	int i;
 	static int found;
@@ -382,10 +382,6 @@ struct net_device * __init atarilance_probe(int unit)
 	dev = alloc_etherdev(sizeof(struct lance_private));
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
 
 	for( i = 0; i < N_LANCE_ADDR; ++i ) {
 		if (lance_probe1( dev, &lance_addr_list[i] )) {
@@ -1137,13 +1133,11 @@ static int lance_set_mac_address( struct net_device *dev, void *addr )
 	return 0;
 }
 
-
-#ifdef MODULE
 static struct net_device *atarilance_dev;
 
 static int __init atarilance_module_init(void)
 {
-	atarilance_dev = atarilance_probe(-1);
+	atarilance_dev = atarilance_probe();
 	return PTR_ERR_OR_ZERO(atarilance_dev);
 }
 
@@ -1155,4 +1149,3 @@ static void __exit atarilance_module_exit(void)
 }
 module_init(atarilance_module_init);
 module_exit(atarilance_module_exit);
-#endif /* MODULE */
diff --git a/drivers/net/ethernet/amd/mvme147.c b/drivers/net/ethernet/amd/mvme147.c
index 3f2e4cdd0b83..da97fccea9ea 100644
--- a/drivers/net/ethernet/amd/mvme147.c
+++ b/drivers/net/ethernet/amd/mvme147.c
@@ -68,7 +68,7 @@ static const struct net_device_ops lance_netdev_ops = {
 };
 
 /* Initialise the one and only on-board 7990 */
-struct net_device * __init mvme147lance_probe(int unit)
+static struct net_device * __init mvme147lance_probe(void)
 {
 	struct net_device *dev;
 	static int called;
@@ -86,9 +86,6 @@ struct net_device * __init mvme147lance_probe(int unit)
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
 
-	if (unit >= 0)
-		sprintf(dev->name, "eth%d", unit);
-
 	/* Fill the dev fields */
 	dev->base_addr = (unsigned long)MVME147_LANCE_BASE;
 	dev->netdev_ops = &lance_netdev_ops;
@@ -179,22 +176,21 @@ static int m147lance_close(struct net_device *dev)
 	return 0;
 }
 
-#ifdef MODULE
 MODULE_LICENSE("GPL");
 
 static struct net_device *dev_mvme147_lance;
-int __init init_module(void)
+static int __init m147lance_init(void)
 {
-	dev_mvme147_lance = mvme147lance_probe(-1);
+	dev_mvme147_lance = mvme147lance_probe();
 	return PTR_ERR_OR_ZERO(dev_mvme147_lance);
 }
+module_init(m147lance_init);
 
-void __exit cleanup_module(void)
+static void __exit m147lance_exit(void)
 {
 	struct m147lance_private *lp = netdev_priv(dev_mvme147_lance);
 	unregister_netdev(dev_mvme147_lance);
 	free_pages(lp->ram, 3);
 	free_netdev(dev_mvme147_lance);
 }
-
-#endif /* MODULE */
+module_exit(m147lance_exit);
diff --git a/drivers/net/ethernet/amd/sun3lance.c b/drivers/net/ethernet/amd/sun3lance.c
index 00ae1081254d..73724b082bdb 100644
--- a/drivers/net/ethernet/amd/sun3lance.c
+++ b/drivers/net/ethernet/amd/sun3lance.c
@@ -245,7 +245,7 @@ static void set_multicast_list( struct net_device *dev );
 
 /************************* End of Prototypes **************************/
 
-struct net_device * __init sun3lance_probe(int unit)
+static struct net_device * __init sun3lance_probe(void)
 {
 	struct net_device *dev;
 	static int found;
@@ -272,10 +272,6 @@ struct net_device * __init sun3lance_probe(int unit)
 	dev = alloc_etherdev(sizeof(struct lance_private));
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
 
 	if (!lance_probe(dev))
 		goto out;
@@ -924,17 +920,16 @@ static void set_multicast_list( struct net_device *dev )
 }
 
 
-#ifdef MODULE
-
 static struct net_device *sun3lance_dev;
 
-int __init init_module(void)
+static int __init sun3lance_init(void)
 {
-	sun3lance_dev = sun3lance_probe(-1);
+	sun3lance_dev = sun3lance_probe();
 	return PTR_ERR_OR_ZERO(sun3lance_dev);
 }
+module_init(sun3lance_init);
 
-void __exit cleanup_module(void)
+static void __exit sun3lance_cleanup(void)
 {
 	unregister_netdev(sun3lance_dev);
 #ifdef CONFIG_SUN3
@@ -942,6 +937,4 @@ void __exit cleanup_module(void)
 #endif
 	free_netdev(sun3lance_dev);
 }
-
-#endif /* MODULE */
-
+module_exit(sun3lance_cleanup);
diff --git a/drivers/net/ethernet/i825xx/82596.c b/drivers/net/ethernet/i825xx/82596.c
index fc8c7cd67471..b8a40146b895 100644
--- a/drivers/net/ethernet/i825xx/82596.c
+++ b/drivers/net/ethernet/i825xx/82596.c
@@ -1110,9 +1110,6 @@ static void print_eth(unsigned char *add, char *str)
 	       add, add + 6, add, add[12], add[13], str);
 }
 
-static int io = 0x300;
-static int irq = 10;
-
 static const struct net_device_ops i596_netdev_ops = {
 	.ndo_open 		= i596_open,
 	.ndo_stop		= i596_close,
@@ -1123,7 +1120,7 @@ static const struct net_device_ops i596_netdev_ops = {
 	.ndo_validate_addr	= eth_validate_addr,
 };
 
-struct net_device * __init i82596_probe(int unit)
+static struct net_device * __init i82596_probe(void)
 {
 	struct net_device *dev;
 	int i;
@@ -1140,14 +1137,6 @@ struct net_device * __init i82596_probe(int unit)
 	if (!dev)
 		return ERR_PTR(-ENOMEM);
 
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	} else {
-		dev->base_addr = io;
-		dev->irq = irq;
-	}
-
 #ifdef ENABLE_MVME16x_NET
 	if (MACH_IS_MVME16x) {
 		if (mvme16x_config & MVME16x_CONFIG_NO_ETHERNET) {
@@ -1515,22 +1504,22 @@ static void set_multicast_list(struct net_device *dev)
 	}
 }
 
-#ifdef MODULE
 static struct net_device *dev_82596;
 
 static int debug = -1;
 module_param(debug, int, 0);
 MODULE_PARM_DESC(debug, "i82596 debug mask");
 
-int __init init_module(void)
+static int __init i82596_init(void)
 {
 	if (debug >= 0)
 		i596_debug = debug;
-	dev_82596 = i82596_probe(-1);
+	dev_82596 = i82596_probe();
 	return PTR_ERR_OR_ZERO(dev_82596);
 }
+module_init(i82596_init);
 
-void __exit cleanup_module(void)
+static void __exit i82596_cleanup(void)
 {
 	unregister_netdev(dev_82596);
 #ifdef __mc68000__
@@ -1544,5 +1533,4 @@ void __exit cleanup_module(void)
 	free_page ((u32)(dev_82596->mem_start));
 	free_netdev(dev_82596);
 }
-
-#endif				/* MODULE */
+module_exit(i82596_cleanup);
diff --git a/drivers/net/ethernet/i825xx/sun3_82586.c b/drivers/net/ethernet/i825xx/sun3_82586.c
index 4564ee02c95f..893e0ddcb611 100644
--- a/drivers/net/ethernet/i825xx/sun3_82586.c
+++ b/drivers/net/ethernet/i825xx/sun3_82586.c
@@ -29,6 +29,7 @@ static int rfdadd = 0; /* rfdadd=1 may be better for 8K MEM cards */
 static int fifo=0x8;	/* don't change */
 
 #include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/string.h>
 #include <linux/errno.h>
 #include <linux/ioport.h>
@@ -276,7 +277,7 @@ static void alloc586(struct net_device *dev)
 	memset((char *)p->scb,0,sizeof(struct scb_struct));
 }
 
-struct net_device * __init sun3_82586_probe(int unit)
+static int __init sun3_82586_probe(void)
 {
 	struct net_device *dev;
 	unsigned long ioaddr;
@@ -291,25 +292,20 @@ struct net_device * __init sun3_82586_probe(int unit)
 		break;
 
 	default:
-		return ERR_PTR(-ENODEV);
+		return -ENODEV;
 	}
 
 	if (found)
-		return ERR_PTR(-ENODEV);
+		return -ENODEV;
 
 	ioaddr = (unsigned long)ioremap(IE_OBIO, SUN3_82586_TOTAL_SIZE);
 	if (!ioaddr)
-		return ERR_PTR(-ENOMEM);
+		return -ENOMEM;
 	found = 1;
 
 	dev = alloc_etherdev(sizeof(struct priv));
 	if (!dev)
 		goto out;
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
-
 	dev->irq = IE_IRQ;
 	dev->base_addr = ioaddr;
 	err = sun3_82586_probe1(dev, ioaddr);
@@ -326,8 +322,9 @@ struct net_device * __init sun3_82586_probe(int unit)
 	free_netdev(dev);
 out:
 	iounmap((void __iomem *)ioaddr);
-	return ERR_PTR(err);
+	return err;
 }
+module_init(sun3_82586_probe);
 
 static const struct net_device_ops sun3_82586_netdev_ops = {
 	.ndo_open		= sun3_82586_open,
diff --git a/include/net/Space.h b/include/net/Space.h
index e30e7a70ea99..93fd6caa4bad 100644
--- a/include/net/Space.h
+++ b/include/net/Space.h
@@ -8,16 +8,10 @@ struct net_device *ultra_probe(int unit);
 struct net_device *wd_probe(int unit);
 struct net_device *ne_probe(int unit);
 struct net_device *fmv18x_probe(int unit);
-struct net_device *i82596_probe(int unit);
 struct net_device *ni65_probe(int unit);
 struct net_device *sonic_probe(int unit);
 struct net_device *smc_init(int unit);
-struct net_device *atarilance_probe(int unit);
-struct net_device *sun3lance_probe(int unit);
-struct net_device *sun3_82586_probe(int unit);
-struct net_device *apne_probe(int unit);
 struct net_device *cs89x0_probe(int unit);
-struct net_device *mvme147lance_probe(int unit);
 struct net_device *tc515_probe(int unit);
 struct net_device *lance_probe(int unit);
 struct net_device *cops_probe(int unit);
-- 
2.29.2

[RFC 07/13] [net-next] move netdev_boot_setup into Space.c

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

This is now only used by a handful of old ISA drivers,
and can be moved into the file they already all depend on.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/Space.c       | 142 ++++++++++++++++++++++++++++++++++++++
 include/linux/netdevice.h |  13 ----
 net/core/dev.c            | 125 ---------------------------------
 net/ethernet/eth.c        |   2 -
 4 files changed, 142 insertions(+), 140 deletions(-)

diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index a03559f23295..f40f2e38682f 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -30,6 +30,148 @@
 #include <linux/netlink.h>
 #include <net/Space.h>
 
+/*
+ * This structure holds boot-time configured netdevice settings. They
+ * are then used in the device probing.
+ */
+struct netdev_boot_setup {
+	char name[IFNAMSIZ];
+	struct ifmap map;
+};
+#define NETDEV_BOOT_SETUP_MAX 8
+
+
+/******************************************************************************
+ *
+ *		      Device Boot-time Settings Routines
+ *
+ ******************************************************************************/
+
+/* Boot time configuration table */
+static struct netdev_boot_setup dev_boot_setup[NETDEV_BOOT_SETUP_MAX];
+
+/**
+ *	netdev_boot_setup_add	- add new setup entry
+ *	@name: name of the device
+ *	@map: configured settings for the device
+ *
+ *	Adds new setup entry to the dev_boot_setup list.  The function
+ *	returns 0 on error and 1 on success.  This is a generic routine to
+ *	all netdevices.
+ */
+static int netdev_boot_setup_add(char *name, struct ifmap *map)
+{
+	struct netdev_boot_setup *s;
+	int i;
+
+	s = dev_boot_setup;
+	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++) {
+		if (s[i].name[0] == '\0' || s[i].name[0] == ' ') {
+			memset(s[i].name, 0, sizeof(s[i].name));
+			strlcpy(s[i].name, name, IFNAMSIZ);
+			memcpy(&s[i].map, map, sizeof(s[i].map));
+			break;
+		}
+	}
+
+	return i >= NETDEV_BOOT_SETUP_MAX ? 0 : 1;
+}
+
+/**
+ * netdev_boot_setup_check	- check boot time settings
+ * @dev: the netdevice
+ *
+ * Check boot time settings for the device.
+ * The found settings are set for the device to be used
+ * later in the device probing.
+ * Returns 0 if no settings found, 1 if they are.
+ */
+int netdev_boot_setup_check(struct net_device *dev)
+{
+	struct netdev_boot_setup *s = dev_boot_setup;
+	int i;
+
+	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++) {
+		if (s[i].name[0] != '\0' && s[i].name[0] != ' ' &&
+		    !strcmp(dev->name, s[i].name)) {
+			dev->irq = s[i].map.irq;
+			dev->base_addr = s[i].map.base_addr;
+			dev->mem_start = s[i].map.mem_start;
+			dev->mem_end = s[i].map.mem_end;
+			return 1;
+		}
+	}
+	return 0;
+}
+EXPORT_SYMBOL(netdev_boot_setup_check);
+
+/**
+ * netdev_boot_base	- get address from boot time settings
+ * @prefix: prefix for network device
+ * @unit: id for network device
+ *
+ * Check boot time settings for the base address of device.
+ * The found settings are set for the device to be used
+ * later in the device probing.
+ * Returns 0 if no settings found.
+ */
+static unsigned long netdev_boot_base(const char *prefix, int unit)
+{
+	const struct netdev_boot_setup *s = dev_boot_setup;
+	char name[IFNAMSIZ];
+	int i;
+
+	sprintf(name, "%s%d", prefix, unit);
+
+	/*
+	 * If device already registered then return base of 1
+	 * to indicate not to probe for this interface
+	 */
+	if (__dev_get_by_name(&init_net, name))
+		return 1;
+
+	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++)
+		if (!strcmp(name, s[i].name))
+			return s[i].map.base_addr;
+	return 0;
+}
+
+/*
+ * Saves at boot time configured settings for any netdevice.
+ */
+static int __init netdev_boot_setup(char *str)
+{
+	int ints[5];
+	struct ifmap map;
+
+	str = get_options(str, ARRAY_SIZE(ints), ints);
+	if (!str || !*str)
+		return 0;
+
+	/* Save settings */
+	memset(&map, 0, sizeof(map));
+	if (ints[0] > 0)
+		map.irq = ints[1];
+	if (ints[0] > 1)
+		map.base_addr = ints[2];
+	if (ints[0] > 2)
+		map.mem_start = ints[3];
+	if (ints[0] > 3)
+		map.mem_end = ints[4];
+
+	/* Add new entry to the list */
+	return netdev_boot_setup_add(str, &map);
+}
+
+__setup("netdev=", netdev_boot_setup);
+
+static int __init ether_boot_setup(char *str)
+{
+	return netdev_boot_setup(str);
+}
+__setup("ether=", ether_boot_setup);
+
+
 /* A unified ethernet device probe.  This is the easiest way to have every
  * ethernet adaptor have the name "eth[0123...]".
  */
diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h
index 5cbc950b34df..75e945a92235 100644
--- a/include/linux/netdevice.h
+++ b/include/linux/netdevice.h
@@ -295,18 +295,6 @@ enum netdev_state_t {
 };
 
 
-/*
- * This structure holds boot-time configured netdevice settings. They
- * are then used in the device probing.
- */
-struct netdev_boot_setup {
-	char name[IFNAMSIZ];
-	struct ifmap map;
-};
-#define NETDEV_BOOT_SETUP_MAX 8
-
-int __init netdev_boot_setup(char *str);
-
 struct gro_list {
 	struct list_head	list;
 	int			count;
@@ -2917,7 +2905,6 @@ static inline struct net_device *first_net_device_rcu(struct net *net)
 }
 
 int netdev_boot_setup_check(struct net_device *dev);
-unsigned long netdev_boot_base(const char *prefix, int unit);
 struct net_device *dev_getbyhwaddr_rcu(struct net *net, unsigned short type,
 				       const char *hwaddr);
 struct net_device *dev_getfirstbyhwtype(struct net *net, unsigned short type);
diff --git a/net/core/dev.c b/net/core/dev.c
index 222b1d322c96..a4309a7f585e 100644
--- a/net/core/dev.c
+++ b/net/core/dev.c
@@ -674,131 +674,6 @@ void dev_remove_offload(struct packet_offload *po)
 }
 EXPORT_SYMBOL(dev_remove_offload);
 
-/******************************************************************************
- *
- *		      Device Boot-time Settings Routines
- *
- ******************************************************************************/
-
-/* Boot time configuration table */
-static struct netdev_boot_setup dev_boot_setup[NETDEV_BOOT_SETUP_MAX];
-
-/**
- *	netdev_boot_setup_add	- add new setup entry
- *	@name: name of the device
- *	@map: configured settings for the device
- *
- *	Adds new setup entry to the dev_boot_setup list.  The function
- *	returns 0 on error and 1 on success.  This is a generic routine to
- *	all netdevices.
- */
-static int netdev_boot_setup_add(char *name, struct ifmap *map)
-{
-	struct netdev_boot_setup *s;
-	int i;
-
-	s = dev_boot_setup;
-	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++) {
-		if (s[i].name[0] == '\0' || s[i].name[0] == ' ') {
-			memset(s[i].name, 0, sizeof(s[i].name));
-			strlcpy(s[i].name, name, IFNAMSIZ);
-			memcpy(&s[i].map, map, sizeof(s[i].map));
-			break;
-		}
-	}
-
-	return i >= NETDEV_BOOT_SETUP_MAX ? 0 : 1;
-}
-
-/**
- * netdev_boot_setup_check	- check boot time settings
- * @dev: the netdevice
- *
- * Check boot time settings for the device.
- * The found settings are set for the device to be used
- * later in the device probing.
- * Returns 0 if no settings found, 1 if they are.
- */
-int netdev_boot_setup_check(struct net_device *dev)
-{
-	struct netdev_boot_setup *s = dev_boot_setup;
-	int i;
-
-	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++) {
-		if (s[i].name[0] != '\0' && s[i].name[0] != ' ' &&
-		    !strcmp(dev->name, s[i].name)) {
-			dev->irq = s[i].map.irq;
-			dev->base_addr = s[i].map.base_addr;
-			dev->mem_start = s[i].map.mem_start;
-			dev->mem_end = s[i].map.mem_end;
-			return 1;
-		}
-	}
-	return 0;
-}
-EXPORT_SYMBOL(netdev_boot_setup_check);
-
-
-/**
- * netdev_boot_base	- get address from boot time settings
- * @prefix: prefix for network device
- * @unit: id for network device
- *
- * Check boot time settings for the base address of device.
- * The found settings are set for the device to be used
- * later in the device probing.
- * Returns 0 if no settings found.
- */
-unsigned long netdev_boot_base(const char *prefix, int unit)
-{
-	const struct netdev_boot_setup *s = dev_boot_setup;
-	char name[IFNAMSIZ];
-	int i;
-
-	sprintf(name, "%s%d", prefix, unit);
-
-	/*
-	 * If device already registered then return base of 1
-	 * to indicate not to probe for this interface
-	 */
-	if (__dev_get_by_name(&init_net, name))
-		return 1;
-
-	for (i = 0; i < NETDEV_BOOT_SETUP_MAX; i++)
-		if (!strcmp(name, s[i].name))
-			return s[i].map.base_addr;
-	return 0;
-}
-
-/*
- * Saves at boot time configured settings for any netdevice.
- */
-int __init netdev_boot_setup(char *str)
-{
-	int ints[5];
-	struct ifmap map;
-
-	str = get_options(str, ARRAY_SIZE(ints), ints);
-	if (!str || !*str)
-		return 0;
-
-	/* Save settings */
-	memset(&map, 0, sizeof(map));
-	if (ints[0] > 0)
-		map.irq = ints[1];
-	if (ints[0] > 1)
-		map.base_addr = ints[2];
-	if (ints[0] > 2)
-		map.mem_start = ints[3];
-	if (ints[0] > 3)
-		map.mem_end = ints[4];
-
-	/* Add new entry to the list */
-	return netdev_boot_setup_add(str, &map);
-}
-
-__setup("netdev=", netdev_boot_setup);
-
 /*******************************************************************************
  *
  *			    Device Interface Subroutines
diff --git a/net/ethernet/eth.c b/net/ethernet/eth.c
index 9cce612e8976..e2c496152dd8 100644
--- a/net/ethernet/eth.c
+++ b/net/ethernet/eth.c
@@ -62,8 +62,6 @@
 #include <linux/uaccess.h>
 #include <net/pkt_sched.h>
 
-__setup("ether=", netdev_boot_setup);
-
 /**
  * eth_header - create the Ethernet header
  * @skb:	buffer to alter
-- 
2.29.2

[RFC 08/13] [net-next] make legacy ISA probe optional

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

There are very few ISA drivers left that rely on the static probing from
drivers/net/Space.o. Make them all select a new CONFIG_NETDEV_LEGACY_INIT
symbol, and drop the entire probe logic when that is disabled.

The 9 drivers that are called from Space.c are the same set that
calls netdev_boot_setup_check().

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/Kconfig                 | 7 +++++++
 drivers/net/Makefile                | 3 ++-
 drivers/net/appletalk/Kconfig       | 4 +++-
 drivers/net/ethernet/3com/Kconfig   | 1 +
 drivers/net/ethernet/8390/Kconfig   | 3 +++
 drivers/net/ethernet/8390/ne.c      | 2 ++
 drivers/net/ethernet/amd/Kconfig    | 2 ++
 drivers/net/ethernet/cirrus/Kconfig | 1 +
 drivers/net/ethernet/smsc/Kconfig   | 1 +
 9 files changed, 22 insertions(+), 2 deletions(-)

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 74dc8e249faa..6dccd68a99d3 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -603,4 +603,11 @@ config NET_FAILOVER
 	  a VM with direct attached VF by failing over to the paravirtual
 	  datapath when the VF is unplugged.
 
+config NETDEV_LEGACY_INIT
+	bool
+	depends on ISA
+	help
+	  Drivers that call netdev_boot_setup_check() should select this
+	  symbol, everything else no longer needs it.
+
 endif # NETDEVICES
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 7ffd2d03efaf..e0ce373c68dd 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -18,7 +18,8 @@ obj-$(CONFIG_MACVLAN) += macvlan.o
 obj-$(CONFIG_MACVTAP) += macvtap.o
 obj-$(CONFIG_MII) += mii.o
 obj-$(CONFIG_MDIO) += mdio.o
-obj-$(CONFIG_NET) += Space.o loopback.o
+obj-$(CONFIG_NET) += loopback.o
+obj-$(CONFIG_NETDEV_LEGACY_INIT) += Space.o
 obj-$(CONFIG_NETCONSOLE) += netconsole.o
 obj-y += phy/
 obj-y += mdio/
diff --git a/drivers/net/appletalk/Kconfig b/drivers/net/appletalk/Kconfig
index 43918398f0d3..90b9f1d6eda9 100644
--- a/drivers/net/appletalk/Kconfig
+++ b/drivers/net/appletalk/Kconfig
@@ -52,7 +52,9 @@ config LTPC
 
 config COPS
 	tristate "COPS LocalTalk PC support"
-	depends on DEV_APPLETALK && (ISA || EISA)
+	depends on DEV_APPLETALK && ISA
+	depends on NETDEVICES
+	select NETDEV_LEGACY_INIT
 	help
 	  This allows you to use COPS AppleTalk cards to connect to LocalTalk
 	  networks. You also need version 1.3.3 or later of the netatalk
diff --git a/drivers/net/ethernet/3com/Kconfig b/drivers/net/ethernet/3com/Kconfig
index a52a3740f0c9..706bd59bf645 100644
--- a/drivers/net/ethernet/3com/Kconfig
+++ b/drivers/net/ethernet/3com/Kconfig
@@ -34,6 +34,7 @@ config EL3
 config 3C515
 	tristate "3c515 ISA \"Fast EtherLink\""
 	depends on ISA && ISA_DMA_API && !PPC32
+	select NETDEV_LEGACY_INIT
 	help
 	  If you have a 3Com ISA EtherLink XL "Corkscrew" 3c515 Fast Ethernet
 	  network card, say Y here.
diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index 9f4b302fd2ce..a4130e643342 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -102,6 +102,7 @@ config MCF8390
 config NE2000
 	tristate "NE2000/NE1000 support"
 	depends on (ISA || (Q40 && m) || MACH_TX49XX || ATARI_ETHERNEC)
+	select NETDEV_LEGACY_INIT if ISA
 	select CRC32
 	help
 	  If you have a network (Ethernet) card of this type, say Y here.
@@ -169,6 +170,7 @@ config STNIC
 config ULTRA
 	tristate "SMC Ultra support"
 	depends on ISA
+	select NETDEV_LEGACY_INIT
 	select CRC32
 	help
 	  If you have a network (Ethernet) card of this type, say Y here.
@@ -186,6 +188,7 @@ config ULTRA
 config WD80x3
 	tristate "WD80*3 support"
 	depends on ISA
+	select NETDEV_LEGACY_INIT
 	select CRC32
 	help
 	  If you have a network (Ethernet) card of this type, say Y here.
diff --git a/drivers/net/ethernet/8390/ne.c b/drivers/net/ethernet/8390/ne.c
index e9756d0ea5b8..d0bbe2180b9e 100644
--- a/drivers/net/ethernet/8390/ne.c
+++ b/drivers/net/ethernet/8390/ne.c
@@ -951,6 +951,7 @@ static int __init ne_init(void)
 }
 module_init(ne_init);
 
+#ifdef CONFIG_NETDEV_LEGACY_INIT
 struct net_device * __init ne_probe(int unit)
 {
 	int this_dev;
@@ -991,6 +992,7 @@ struct net_device * __init ne_probe(int unit)
 
 	return ERR_PTR(-ENODEV);
 }
+#endif
 #endif /* MODULE */
 
 static void __exit ne_exit(void)
diff --git a/drivers/net/ethernet/amd/Kconfig b/drivers/net/ethernet/amd/Kconfig
index d0b0609bbe23..c6a3abec86f5 100644
--- a/drivers/net/ethernet/amd/Kconfig
+++ b/drivers/net/ethernet/amd/Kconfig
@@ -46,6 +46,7 @@ config AMD8111_ETH
 config LANCE
 	tristate "AMD LANCE and PCnet (AT1500 and NE2100) support"
 	depends on ISA && ISA_DMA_API && !ARM && !PPC32
+	select NETDEV_LEGACY_INIT
 	help
 	  If you have a network (Ethernet) card of this type, say Y here.
 	  Some LinkSys cards are of this type.
@@ -132,6 +133,7 @@ config PCMCIA_NMCLAN
 config NI65
 	tristate "NI6510 support"
 	depends on ISA && ISA_DMA_API && !ARM && !PPC32
+	select NETDEV_LEGACY_INIT
 	help
 	  If you have a network (Ethernet) card of this type, say Y here.
 
diff --git a/drivers/net/ethernet/cirrus/Kconfig b/drivers/net/ethernet/cirrus/Kconfig
index 7141340a8b0e..dac1764ba740 100644
--- a/drivers/net/ethernet/cirrus/Kconfig
+++ b/drivers/net/ethernet/cirrus/Kconfig
@@ -26,6 +26,7 @@ config CS89x0_ISA
 	depends on ISA
 	depends on !PPC32
 	depends on CS89x0_PLATFORM=n
+	select NETDEV_LEGACY_INIT
 	select CS89x0
 	help
 	  Support for CS89x0 chipset based Ethernet cards. If you have a
diff --git a/drivers/net/ethernet/smsc/Kconfig b/drivers/net/ethernet/smsc/Kconfig
index c52a38df0e0d..72e42a868346 100644
--- a/drivers/net/ethernet/smsc/Kconfig
+++ b/drivers/net/ethernet/smsc/Kconfig
@@ -23,6 +23,7 @@ config SMC9194
 	tristate "SMC 9194 support"
 	depends on ISA
 	select CRC32
+	select NETDEV_LEGACY_INIT
 	help
 	  This is support for the SMC9xxx based Ethernet cards. Choose this
 	  option if you have a DELL laptop with the docking station, or
-- 
2.29.2

[RFC 09/13] [net-next] wan: remove stale Kconfig entries

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

The dscc4 driver was removed in 2019 but these Kconfig entries remain,
so remove them as well.

Fixes: 28c9eb9042a9 ("net/wan: dscc4: remove broken dscc4 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/wan/Kconfig | 24 ------------------------
 1 file changed, 24 deletions(-)

diff --git a/drivers/net/wan/Kconfig b/drivers/net/wan/Kconfig
index 83c9481995dd..f59ebafa3761 100644
--- a/drivers/net/wan/Kconfig
+++ b/drivers/net/wan/Kconfig
@@ -290,30 +290,6 @@ config SLIC_DS26522
 	  To compile this driver as a module, choose M here: the
 	  module will be called slic_ds26522.
 
-config DSCC4_PCISYNC
-	bool "Etinc PCISYNC features"
-	depends on DSCC4
-	help
-	  Due to Etinc's design choice for its PCISYNC cards, some operations
-	  are only allowed on specific ports of the DSCC4. This option is the
-	  only way for the driver to know that it shouldn't return a success
-	  code for these operations.
-
-	  Please say Y if your card is an Etinc's PCISYNC.
-
-config DSCC4_PCI_RST
-	bool "Hard reset support"
-	depends on DSCC4
-	help
-	  Various DSCC4 bugs forbid any reliable software reset of the ASIC.
-	  As a replacement, some vendors provide a way to assert the PCI #RST
-	  pin of DSCC4 through the GPIO port of the card. If you choose Y,
-	  the driver will make use of this feature before module removal
-	  (i.e. rmmod). The feature is known to be available on Commtech's
-	  cards. Contact your manufacturer for details.
-
-	  Say Y if your card supports this feature.
-
 config IXP4XX_HSS
 	tristate "Intel IXP4xx HSS (synchronous serial port) support"
 	depends on HDLC && IXP4XX_NPE && IXP4XX_QMGR
-- 
2.29.2

[RFC 10/13] [net-next] wan: remove sbni/granch driver

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

The driver was merged in 1999 and has only ever seen treewide cleanups
since then, with no indication whatsoever that anyone has actually
had access to hardware for testing the patches.

From the information in the link below, it appears that the hardware
is for some leased line system in Russia that has since been
discontinued, and useless without any remote end to connect to.

As the driver still feels like a Linux-2.2 era artifact today, it
appears that the best way forward is to just delete it.

Link: https://www.tms.ru/%D0%90%D0%B4%D0%B0%D0%BF%D1%82%D0%B5%D1%80_%D0%B4%D0%BB%D1%8F_%D0%B2%D1%8B%D0%B4%D0%B5%D0%BB%D0%B5%D0%BD%D0%BD%D1%8B%D1%85_%D0%BB%D0%B8%D0%BD%D0%B8%D0%B9_Granch_SBNI12-10
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 .../admin-guide/kernel-parameters.txt         |    2 -
 drivers/net/Space.c                           |    4 -
 drivers/net/wan/Kconfig                       |   27 -
 drivers/net/wan/Makefile                      |    1 -
 drivers/net/wan/sbni.c                        | 1638 -----------------
 drivers/net/wan/sbni.h                        |  147 --
 include/net/Space.h                           |    3 -
 7 files changed, 1822 deletions(-)
 delete mode 100644 drivers/net/wan/sbni.c
 delete mode 100644 drivers/net/wan/sbni.h

diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index cb89dbdedc46..0dc2404207a7 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -4876,8 +4876,6 @@
 	sa1100ir	[NET]
 			See drivers/net/irda/sa1100_ir.c.
 
-	sbni=		[NET] Granch SBNI12 leased line adapter
-
 	sched_verbose	[KNL] Enables verbose scheduler debug messages.
 
 	schedstats=	[KNL,X86] Enable or disable scheduled statistics.
diff --git a/drivers/net/Space.c b/drivers/net/Space.c
index f40f2e38682f..49e67c9fb5a4 100644
--- a/drivers/net/Space.c
+++ b/drivers/net/Space.c
@@ -247,10 +247,6 @@ static int __init net_olddevs_init(void)
 {
 	int num;
 
-#ifdef CONFIG_SBNI
-	for (num = 0; num < 8; ++num)
-		sbni_probe(num);
-#endif
 	for (num = 0; num < 8; ++num)
 		ethif_probe2(num);
 
diff --git a/drivers/net/wan/Kconfig b/drivers/net/wan/Kconfig
index f59ebafa3761..a187c814a4a6 100644
--- a/drivers/net/wan/Kconfig
+++ b/drivers/net/wan/Kconfig
@@ -313,33 +313,6 @@ config LAPBETHER
 	  To compile this driver as a module, choose M here: the
 	  module will be called lapbether.
 
-	  If unsure, say N.
-
-config SBNI
-	tristate "Granch SBNI12 Leased Line adapter support"
-	depends on X86
-	help
-	  Driver for ISA SBNI12-xx cards which are low cost alternatives to
-	  leased line modems.
-
-	  You can find more information and last versions of drivers and
-	  utilities at <http://www.granch.ru/>. If you have any question you
-	  can send email to <sbni@granch.ru>.
-
-	  To compile this driver as a module, choose M here: the
-	  module will be called sbni.
-
-	  If unsure, say N.
-
-config SBNI_MULTILINE
-	bool "Multiple line feature support"
-	depends on SBNI
-	help
-	  Schedule traffic for some parallel lines, via SBNI12 adapters.
-
-	  If you have two computers connected with two parallel lines it's
-	  possible to increase transfer rate nearly twice. You should have
-	  a program named 'sbniconfig' to configure adapters.
 
 	  If unsure, say N.
 
diff --git a/drivers/net/wan/Makefile b/drivers/net/wan/Makefile
index 081666c36ca2..f6b92efffc94 100644
--- a/drivers/net/wan/Makefile
+++ b/drivers/net/wan/Makefile
@@ -22,7 +22,6 @@ obj-$(CONFIG_FARSYNC)		+= farsync.o
 obj-$(CONFIG_LANMEDIA)		+= lmc/
 
 obj-$(CONFIG_LAPBETHER)		+= lapbether.o
-obj-$(CONFIG_SBNI)		+= sbni.o
 obj-$(CONFIG_N2)		+= n2.o
 obj-$(CONFIG_C101)		+= c101.o
 obj-$(CONFIG_WANXL)		+= wanxl.o
diff --git a/drivers/net/wan/sbni.c b/drivers/net/wan/sbni.c
deleted file mode 100644
index 3092a09d3eaa..000000000000
--- a/drivers/net/wan/sbni.c
+++ /dev/null
@@ -1,1638 +0,0 @@
-/* sbni.c:  Granch SBNI12 leased line adapters driver for linux
- *
- *	Written 2001 by Denis I.Timofeev (timofeev@granch.ru)
- *
- *	Previous versions were written by Yaroslav Polyakov,
- *	Alexey Zverev and Max Khon.
- *
- *	Driver supports SBNI12-02,-04,-05,-10,-11 cards, single and
- *	double-channel, PCI and ISA modifications.
- *	More info and useful utilities to work with SBNI12 cards you can find
- *	at http://www.granch.com (English) or http://www.granch.ru (Russian)
- *
- *	This software may be used and distributed according to the terms
- *	of the GNU General Public License.
- *
- *
- *  5.0.1	Jun 22 2001
- *	  - Fixed bug in probe
- *  5.0.0	Jun 06 2001
- *	  - Driver was completely redesigned by Denis I.Timofeev,
- *	  - now PCI/Dual, ISA/Dual (with single interrupt line) models are
- *	  - supported
- *  3.3.0	Thu Feb 24 21:30:28 NOVT 2000 
- *        - PCI cards support
- *  3.2.0	Mon Dec 13 22:26:53 NOVT 1999
- * 	  - Completely rebuilt all the packet storage system
- * 	  -    to work in Ethernet-like style.
- *  3.1.1	just fixed some bugs (5 aug 1999)
- *  3.1.0	added balancing feature	(26 apr 1999)
- *  3.0.1	just fixed some bugs (14 apr 1999).
- *  3.0.0	Initial Revision, Yaroslav Polyakov (24 Feb 1999)
- *        - added pre-calculation for CRC, fixed bug with "len-2" frames, 
- *        - removed outbound fragmentation (MTU=1000), written CRC-calculation 
- *        - on asm, added work with hard_headers and now we have our own cache 
- *        - for them, optionally supported word-interchange on some chipsets,
- * 
- *	Known problem: this driver wasn't tested on multiprocessor machine.
- */
-
-#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/ptrace.h>
-#include <linux/fcntl.h>
-#include <linux/ioport.h>
-#include <linux/interrupt.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/pci.h>
-#include <linux/skbuff.h>
-#include <linux/timer.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-
-#include <net/net_namespace.h>
-#include <net/arp.h>
-#include <net/Space.h>
-
-#include <asm/io.h>
-#include <asm/types.h>
-#include <asm/byteorder.h>
-#include <asm/irq.h>
-#include <linux/uaccess.h>
-
-#include "sbni.h"
-
-/* device private data */
-
-struct net_local {
-	struct timer_list	watchdog;
-	struct net_device	*watchdog_dev;
-
-	spinlock_t	lock;
-	struct sk_buff  *rx_buf_p;		/* receive buffer ptr */
-	struct sk_buff  *tx_buf_p;		/* transmit buffer ptr */
-	
-	unsigned int	framelen;		/* current frame length */
-	unsigned int	maxframe;		/* maximum valid frame length */
-	unsigned int	state;
-	unsigned int	inppos, outpos;		/* positions in rx/tx buffers */
-
-	/* transmitting frame number - from frames qty to 1 */
-	unsigned int	tx_frameno;
-
-	/* expected number of next receiving frame */
-	unsigned int	wait_frameno;
-
-	/* count of failed attempts to frame send - 32 attempts do before
-	   error - while receiver tunes on opposite side of wire */
-	unsigned int	trans_errors;
-
-	/* idle time; send pong when limit exceeded */
-	unsigned int	timer_ticks;
-
-	/* fields used for receive level autoselection */
-	int	delta_rxl;
-	unsigned int	cur_rxl_index, timeout_rxl;
-	unsigned long	cur_rxl_rcvd, prev_rxl_rcvd;
-
-	struct sbni_csr1	csr1;		/* current value of CSR1 */
-	struct sbni_in_stats	in_stats; 	/* internal statistics */ 
-
-	struct net_device		*second;	/* for ISA/dual cards */
-
-#ifdef CONFIG_SBNI_MULTILINE
-	struct net_device		*master;
-	struct net_device		*link;
-#endif
-};
-
-
-static int  sbni_card_probe( unsigned long );
-static int  sbni_pci_probe( struct net_device  * );
-static struct net_device  *sbni_probe1(struct net_device *, unsigned long, int);
-static int  sbni_open( struct net_device * );
-static int  sbni_close( struct net_device * );
-static netdev_tx_t sbni_start_xmit(struct sk_buff *,
-					 struct net_device * );
-static int  sbni_ioctl( struct net_device *, struct ifreq *, int );
-static void  set_multicast_list( struct net_device * );
-
-static irqreturn_t sbni_interrupt( int, void * );
-static void  handle_channel( struct net_device * );
-static int   recv_frame( struct net_device * );
-static void  send_frame( struct net_device * );
-static int   upload_data( struct net_device *,
-			  unsigned, unsigned, unsigned, u32 );
-static void  download_data( struct net_device *, u32 * );
-static void  sbni_watchdog(struct timer_list *);
-static void  interpret_ack( struct net_device *, unsigned );
-static int   append_frame_to_pkt( struct net_device *, unsigned, u32 );
-static void  indicate_pkt( struct net_device * );
-static void  card_start( struct net_device * );
-static void  prepare_to_send( struct sk_buff *, struct net_device * );
-static void  drop_xmit_queue( struct net_device * );
-static void  send_frame_header( struct net_device *, u32 * );
-static int   skip_tail( unsigned int, unsigned int, u32 );
-static int   check_fhdr( u32, u32 *, u32 *, u32 *, u32 *, u32 * );
-static void  change_level( struct net_device * );
-static void  timeout_change_level( struct net_device * );
-static u32   calc_crc32( u32, u8 *, u32 );
-static struct sk_buff *  get_rx_buf( struct net_device * );
-static int  sbni_init( struct net_device * );
-
-#ifdef CONFIG_SBNI_MULTILINE
-static int  enslave( struct net_device *, struct net_device * );
-static int  emancipate( struct net_device * );
-#endif
-
-static const char  version[] =
-	"Granch SBNI12 driver ver 5.0.1  Jun 22 2001  Denis I.Timofeev.\n";
-
-static bool skip_pci_probe	__initdata = false;
-static int  scandone	__initdata = 0;
-static int  num		__initdata = 0;
-
-static unsigned char  rxl_tab[];
-static u32  crc32tab[];
-
-/* A list of all installed devices, for removing the driver module. */
-static struct net_device  *sbni_cards[ SBNI_MAX_NUM_CARDS ];
-
-/* Lists of device's parameters */
-static u32	io[   SBNI_MAX_NUM_CARDS ] __initdata =
-	{ [0 ... SBNI_MAX_NUM_CARDS-1] = -1 };
-static u32	irq[  SBNI_MAX_NUM_CARDS ] __initdata;
-static u32	baud[ SBNI_MAX_NUM_CARDS ] __initdata;
-static u32	rxl[  SBNI_MAX_NUM_CARDS ] __initdata =
-	{ [0 ... SBNI_MAX_NUM_CARDS-1] = -1 };
-static u32	mac[  SBNI_MAX_NUM_CARDS ] __initdata;
-
-#ifndef MODULE
-typedef u32  iarr[];
-static iarr *dest[5] __initdata = { &io, &irq, &baud, &rxl, &mac };
-#endif
-
-/* A zero-terminated list of I/O addresses to be probed on ISA bus */
-static unsigned int  netcard_portlist[ ] __initdata = { 
-	0x210, 0x214, 0x220, 0x224, 0x230, 0x234, 0x240, 0x244, 0x250, 0x254,
-	0x260, 0x264, 0x270, 0x274, 0x280, 0x284, 0x290, 0x294, 0x2a0, 0x2a4,
-	0x2b0, 0x2b4, 0x2c0, 0x2c4, 0x2d0, 0x2d4, 0x2e0, 0x2e4, 0x2f0, 0x2f4,
-	0 };
-
-#define NET_LOCAL_LOCK(dev) (((struct net_local *)netdev_priv(dev))->lock)
-
-/*
- * Look for SBNI card which addr stored in dev->base_addr, if nonzero.
- * Otherwise, look through PCI bus. If none PCI-card was found, scan ISA.
- */
-
-static inline int __init
-sbni_isa_probe( struct net_device  *dev )
-{
-	if( dev->base_addr > 0x1ff &&
-	    request_region( dev->base_addr, SBNI_IO_EXTENT, dev->name ) &&
-	    sbni_probe1( dev, dev->base_addr, dev->irq ) )
-
-		return  0;
-	else {
-		pr_err("base address 0x%lx is busy, or adapter is malfunctional!\n",
-		       dev->base_addr);
-		return  -ENODEV;
-	}
-}
-
-static const struct net_device_ops sbni_netdev_ops = {
-	.ndo_open		= sbni_open,
-	.ndo_stop		= sbni_close,
-	.ndo_start_xmit		= sbni_start_xmit,
-	.ndo_set_rx_mode	= set_multicast_list,
-	.ndo_do_ioctl		= sbni_ioctl,
-	.ndo_set_mac_address 	= eth_mac_addr,
-	.ndo_validate_addr	= eth_validate_addr,
-};
-
-static void __init sbni_devsetup(struct net_device *dev)
-{
-	ether_setup( dev );
-	dev->netdev_ops = &sbni_netdev_ops;
-}
-
-int __init sbni_probe(int unit)
-{
-	struct net_device *dev;
-	int err;
-
-	dev = alloc_netdev(sizeof(struct net_local), "sbni",
-			   NET_NAME_UNKNOWN, sbni_devsetup);
-	if (!dev)
-		return -ENOMEM;
-
-	dev->netdev_ops = &sbni_netdev_ops;
-
-	sprintf(dev->name, "sbni%d", unit);
-	netdev_boot_setup_check(dev);
-
-	err = sbni_init(dev);
-	if (err) {
-		free_netdev(dev);
-		return err;
-	}
-
-	err = register_netdev(dev);
-	if (err) {
-		release_region( dev->base_addr, SBNI_IO_EXTENT );
-		free_netdev(dev);
-		return err;
-	}
-	pr_info_once("%s", version);
-	return 0;
-}
-
-static int __init sbni_init(struct net_device *dev)
-{
-	int  i;
-	if( dev->base_addr )
-		return  sbni_isa_probe( dev );
-	/* otherwise we have to perform search our adapter */
-
-	if( io[ num ] != -1 ) {
-		dev->base_addr	= io[ num ];
-		dev->irq	= irq[ num ];
-	} else if( scandone  ||  io[ 0 ] != -1 ) {
-		return  -ENODEV;
-	}
-
-	/* if io[ num ] contains non-zero address, then that is on ISA bus */
-	if( dev->base_addr )
-		return  sbni_isa_probe( dev );
-
-	/* ...otherwise - scan PCI first */
-	if( !skip_pci_probe  &&  !sbni_pci_probe( dev ) )
-		return  0;
-
-	if( io[ num ] == -1 ) {
-		/* Auto-scan will be stopped when first ISA card were found */
-		scandone = 1;
-		if( num > 0 )
-			return  -ENODEV;
-	}
-
-	for( i = 0;  netcard_portlist[ i ];  ++i ) {
-		int  ioaddr = netcard_portlist[ i ];
-		if( request_region( ioaddr, SBNI_IO_EXTENT, dev->name ) &&
-		    sbni_probe1( dev, ioaddr, 0 ))
-			return 0;
-	}
-
-	return  -ENODEV;
-}
-
-
-static int __init
-sbni_pci_probe( struct net_device  *dev )
-{
-	struct pci_dev  *pdev = NULL;
-
-	while( (pdev = pci_get_class( PCI_CLASS_NETWORK_OTHER << 8, pdev ))
-	       != NULL ) {
-		int  pci_irq_line;
-		unsigned long  pci_ioaddr;
-
-		if( pdev->vendor != SBNI_PCI_VENDOR &&
-		    pdev->device != SBNI_PCI_DEVICE )
-			continue;
-
-		pci_ioaddr = pci_resource_start( pdev, 0 );
-		pci_irq_line = pdev->irq;
-
-		/* Avoid already found cards from previous calls */
-		if( !request_region( pci_ioaddr, SBNI_IO_EXTENT, dev->name ) ) {
-			if (pdev->subsystem_device != 2)
-				continue;
-
-			/* Dual adapter is present */
-			if (!request_region(pci_ioaddr += 4, SBNI_IO_EXTENT,
-							dev->name ) )
-				continue;
-		}
-
-		if (pci_irq_line <= 0 || pci_irq_line >= nr_irqs)
-			pr_warn(
-"WARNING: The PCI BIOS assigned this PCI card to IRQ %d, which is unlikely to work!.\n"
-"You should use the PCI BIOS setup to assign a valid IRQ line.\n",
-				pci_irq_line );
-
-		/* avoiding re-enable dual adapters */
-		if( (pci_ioaddr & 7) == 0  &&  pci_enable_device( pdev ) ) {
-			release_region( pci_ioaddr, SBNI_IO_EXTENT );
-			pci_dev_put( pdev );
-			return  -EIO;
-		}
-		if( sbni_probe1( dev, pci_ioaddr, pci_irq_line ) ) {
-			SET_NETDEV_DEV(dev, &pdev->dev);
-			/* not the best thing to do, but this is all messed up 
-			   for hotplug systems anyway... */
-			pci_dev_put( pdev );
-			return  0;
-		}
-	}
-	return  -ENODEV;
-}
-
-
-static struct net_device * __init
-sbni_probe1( struct net_device  *dev,  unsigned long  ioaddr,  int  irq )
-{
-	struct net_local  *nl;
-
-	if( sbni_card_probe( ioaddr ) ) {
-		release_region( ioaddr, SBNI_IO_EXTENT );
-		return NULL;
-	}
-
-	outb( 0, ioaddr + CSR0 );
-
-	if( irq < 2 ) {
-		unsigned long irq_mask;
-
-		irq_mask = probe_irq_on();
-		outb( EN_INT | TR_REQ, ioaddr + CSR0 );
-		outb( PR_RES, ioaddr + CSR1 );
-		mdelay(50);
-		irq = probe_irq_off(irq_mask);
-		outb( 0, ioaddr + CSR0 );
-
-		if( !irq ) {
-			pr_err("%s: can't detect device irq!\n", dev->name);
-			release_region( ioaddr, SBNI_IO_EXTENT );
-			return NULL;
-		}
-	} else if( irq == 2 )
-		irq = 9;
-
-	dev->irq = irq;
-	dev->base_addr = ioaddr;
-
-	/* Fill in sbni-specific dev fields. */
-	nl = netdev_priv(dev);
-	if( !nl ) {
-		pr_err("%s: unable to get memory!\n", dev->name);
-		release_region( ioaddr, SBNI_IO_EXTENT );
-		return NULL;
-	}
-
-	memset( nl, 0, sizeof(struct net_local) );
-	spin_lock_init( &nl->lock );
-
-	/* store MAC address (generate if that isn't known) */
-	*(__be16 *)dev->dev_addr = htons( 0x00ff );
-	*(__be32 *)(dev->dev_addr + 2) = htonl( 0x01000000 |
-		((mac[num] ?
-		mac[num] :
-		(u32)((long)netdev_priv(dev))) & 0x00ffffff));
-
-	/* store link settings (speed, receive level ) */
-	nl->maxframe  = DEFAULT_FRAME_LEN;
-	nl->csr1.rate = baud[ num ];
-
-	if( (nl->cur_rxl_index = rxl[ num ]) == -1 ) {
-		/* autotune rxl */
-		nl->cur_rxl_index = DEF_RXL;
-		nl->delta_rxl = DEF_RXL_DELTA;
-	} else {
-		nl->delta_rxl = 0;
-	}
-	nl->csr1.rxl  = rxl_tab[ nl->cur_rxl_index ];
-	if( inb( ioaddr + CSR0 ) & 0x01 )
-		nl->state |= FL_SLOW_MODE;
-
-	pr_notice("%s: ioaddr %#lx, irq %d, MAC: 00:ff:01:%02x:%02x:%02x\n",
-		  dev->name, dev->base_addr, dev->irq,
-		  ((u8 *)dev->dev_addr)[3],
-		  ((u8 *)dev->dev_addr)[4],
-		  ((u8 *)dev->dev_addr)[5]);
-
-	pr_notice("%s: speed %d",
-		  dev->name,
-		  ((nl->state & FL_SLOW_MODE) ? 500000 : 2000000)
-		  / (1 << nl->csr1.rate));
-
-	if( nl->delta_rxl == 0 )
-		pr_cont(", receive level 0x%x (fixed)\n", nl->cur_rxl_index);
-	else
-		pr_cont(", receive level (auto)\n");
-
-#ifdef CONFIG_SBNI_MULTILINE
-	nl->master = dev;
-	nl->link   = NULL;
-#endif
-   
-	sbni_cards[ num++ ] = dev;
-	return  dev;
-}
-
-/* -------------------------------------------------------------------------- */
-
-#ifdef CONFIG_SBNI_MULTILINE
-
-static netdev_tx_t
-sbni_start_xmit( struct sk_buff  *skb,  struct net_device  *dev )
-{
-	struct net_device  *p;
-
-	netif_stop_queue( dev );
-
-	/* Looking for idle device in the list */
-	for( p = dev;  p; ) {
-		struct net_local  *nl = netdev_priv(p);
-		spin_lock( &nl->lock );
-		if( nl->tx_buf_p  ||  (nl->state & FL_LINE_DOWN) ) {
-			p = nl->link;
-			spin_unlock( &nl->lock );
-		} else {
-			/* Idle dev is found */
-			prepare_to_send( skb, p );
-			spin_unlock( &nl->lock );
-			netif_start_queue( dev );
-			return NETDEV_TX_OK;
-		}
-	}
-
-	return NETDEV_TX_BUSY;
-}
-
-#else	/* CONFIG_SBNI_MULTILINE */
-
-static netdev_tx_t
-sbni_start_xmit( struct sk_buff  *skb,  struct net_device  *dev )
-{
-	struct net_local  *nl  = netdev_priv(dev);
-
-	netif_stop_queue( dev );
-	spin_lock( &nl->lock );
-
-	prepare_to_send( skb, dev );
-
-	spin_unlock( &nl->lock );
-	return NETDEV_TX_OK;
-}
-
-#endif	/* CONFIG_SBNI_MULTILINE */
-
-/* -------------------------------------------------------------------------- */
-
-/* interrupt handler */
-
-/*
- * 	SBNI12D-10, -11/ISA boards within "common interrupt" mode could not
- * be looked as two independent single-channel devices. Every channel seems
- * as Ethernet interface but interrupt handler must be common. Really, first
- * channel ("master") driver only registers the handler. In its struct net_local
- * it has got pointer to "slave" channel's struct net_local and handles that's
- * interrupts too.
- *	dev of successfully attached ISA SBNI boards is linked to list.
- * While next board driver is initialized, it scans this list. If one
- * has found dev with same irq and ioaddr different by 4 then it assumes
- * this board to be "master".
- */ 
-
-static irqreturn_t
-sbni_interrupt( int  irq,  void  *dev_id )
-{
-	struct net_device	  *dev = dev_id;
-	struct net_local  *nl  = netdev_priv(dev);
-	int	repeat;
-
-	spin_lock( &nl->lock );
-	if( nl->second )
-		spin_lock(&NET_LOCAL_LOCK(nl->second));
-
-	do {
-		repeat = 0;
-		if( inb( dev->base_addr + CSR0 ) & (RC_RDY | TR_RDY) ) {
-			handle_channel( dev );
-			repeat = 1;
-		}
-		if( nl->second  && 	/* second channel present */
-		    (inb( nl->second->base_addr+CSR0 ) & (RC_RDY | TR_RDY)) ) {
-			handle_channel( nl->second );
-			repeat = 1;
-		}
-	} while( repeat );
-
-	if( nl->second )
-		spin_unlock(&NET_LOCAL_LOCK(nl->second));
-	spin_unlock( &nl->lock );
-	return IRQ_HANDLED;
-}
-
-
-static void
-handle_channel( struct net_device  *dev )
-{
-	struct net_local	*nl    = netdev_priv(dev);
-	unsigned long		ioaddr = dev->base_addr;
-
-	int  req_ans;
-	unsigned char  csr0;
-
-#ifdef CONFIG_SBNI_MULTILINE
-	/* Lock the master device because we going to change its local data */
-	if( nl->state & FL_SLAVE )
-		spin_lock(&NET_LOCAL_LOCK(nl->master));
-#endif
-
-	outb( (inb( ioaddr + CSR0 ) & ~EN_INT) | TR_REQ, ioaddr + CSR0 );
-
-	nl->timer_ticks = CHANGE_LEVEL_START_TICKS;
-	for(;;) {
-		csr0 = inb( ioaddr + CSR0 );
-		if( ( csr0 & (RC_RDY | TR_RDY) ) == 0 )
-			break;
-
-		req_ans = !(nl->state & FL_PREV_OK);
-
-		if( csr0 & RC_RDY )
-			req_ans = recv_frame( dev );
-
-		/*
-		 * TR_RDY always equals 1 here because we have owned the marker,
-		 * and we set TR_REQ when disabled interrupts
-		 */
-		csr0 = inb( ioaddr + CSR0 );
-		if( !(csr0 & TR_RDY)  ||  (csr0 & RC_RDY) )
-			netdev_err(dev, "internal error!\n");
-
-		/* if state & FL_NEED_RESEND != 0 then tx_frameno != 0 */
-		if( req_ans  ||  nl->tx_frameno != 0 )
-			send_frame( dev );
-		else
-			/* send marker without any data */
-			outb( inb( ioaddr + CSR0 ) & ~TR_REQ, ioaddr + CSR0 );
-	}
-
-	outb( inb( ioaddr + CSR0 ) | EN_INT, ioaddr + CSR0 );
-
-#ifdef CONFIG_SBNI_MULTILINE
-	if( nl->state & FL_SLAVE )
-		spin_unlock(&NET_LOCAL_LOCK(nl->master));
-#endif
-}
-
-
-/*
- * Routine returns 1 if it needs to acknowledge received frame.
- * Empty frame received without errors won't be acknowledged.
- */
-
-static int
-recv_frame( struct net_device  *dev )
-{
-	struct net_local  *nl   = netdev_priv(dev);
-	unsigned long  ioaddr	= dev->base_addr;
-
-	u32  crc = CRC32_INITIAL;
-
-	unsigned  framelen = 0, frameno, ack;
-	unsigned  is_first, frame_ok = 0;
-
-	if( check_fhdr( ioaddr, &framelen, &frameno, &ack, &is_first, &crc ) ) {
-		frame_ok = framelen > 4
-			?  upload_data( dev, framelen, frameno, is_first, crc )
-			:  skip_tail( ioaddr, framelen, crc );
-		if( frame_ok )
-			interpret_ack( dev, ack );
-	}
-
-	outb( inb( ioaddr + CSR0 ) ^ CT_ZER, ioaddr + CSR0 );
-	if( frame_ok ) {
-		nl->state |= FL_PREV_OK;
-		if( framelen > 4 )
-			nl->in_stats.all_rx_number++;
-	} else {
-		nl->state &= ~FL_PREV_OK;
-		change_level( dev );
-		nl->in_stats.all_rx_number++;
-		nl->in_stats.bad_rx_number++;
-	}
-
-	return  !frame_ok  ||  framelen > 4;
-}
-
-
-static void
-send_frame( struct net_device  *dev )
-{
-	struct net_local  *nl    = netdev_priv(dev);
-
-	u32  crc = CRC32_INITIAL;
-
-	if( nl->state & FL_NEED_RESEND ) {
-
-		/* if frame was sended but not ACK'ed - resend it */
-		if( nl->trans_errors ) {
-			--nl->trans_errors;
-			if( nl->framelen != 0 )
-				nl->in_stats.resend_tx_number++;
-		} else {
-			/* cannot xmit with many attempts */
-#ifdef CONFIG_SBNI_MULTILINE
-			if( (nl->state & FL_SLAVE)  ||  nl->link )
-#endif
-			nl->state |= FL_LINE_DOWN;
-			drop_xmit_queue( dev );
-			goto  do_send;
-		}
-	} else
-		nl->trans_errors = TR_ERROR_COUNT;
-
-	send_frame_header( dev, &crc );
-	nl->state |= FL_NEED_RESEND;
-	/*
-	 * FL_NEED_RESEND will be cleared after ACK, but if empty
-	 * frame sended then in prepare_to_send next frame
-	 */
-
-
-	if( nl->framelen ) {
-		download_data( dev, &crc );
-		nl->in_stats.all_tx_number++;
-		nl->state |= FL_WAIT_ACK;
-	}
-
-	outsb( dev->base_addr + DAT, (u8 *)&crc, sizeof crc );
-
-do_send:
-	outb( inb( dev->base_addr + CSR0 ) & ~TR_REQ, dev->base_addr + CSR0 );
-
-	if( nl->tx_frameno )
-		/* next frame exists - we request card to send it */
-		outb( inb( dev->base_addr + CSR0 ) | TR_REQ,
-		      dev->base_addr + CSR0 );
-}
-
-
-/*
- * Write the frame data into adapter's buffer memory, and calculate CRC.
- * Do padding if necessary.
- */
-
-static void
-download_data( struct net_device  *dev,  u32  *crc_p )
-{
-	struct net_local  *nl    = netdev_priv(dev);
-	struct sk_buff    *skb	 = nl->tx_buf_p;
-
-	unsigned  len = min_t(unsigned int, skb->len - nl->outpos, nl->framelen);
-
-	outsb( dev->base_addr + DAT, skb->data + nl->outpos, len );
-	*crc_p = calc_crc32( *crc_p, skb->data + nl->outpos, len );
-
-	/* if packet too short we should write some more bytes to pad */
-	for( len = nl->framelen - len;  len--; ) {
-		outb( 0, dev->base_addr + DAT );
-		*crc_p = CRC32( 0, *crc_p );
-	}
-}
-
-
-static int
-upload_data( struct net_device  *dev,  unsigned  framelen,  unsigned  frameno,
-	     unsigned  is_first,  u32  crc )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	int  frame_ok;
-
-	if( is_first ) {
-		nl->wait_frameno = frameno;
-		nl->inppos = 0;
-	}
-
-	if( nl->wait_frameno == frameno ) {
-
-		if( nl->inppos + framelen  <=  ETHER_MAX_LEN )
-			frame_ok = append_frame_to_pkt( dev, framelen, crc );
-
-		/*
-		 * if CRC is right but framelen incorrect then transmitter
-		 * error was occurred... drop entire packet
-		 */
-		else if( (frame_ok = skip_tail( dev->base_addr, framelen, crc ))
-			 != 0 ) {
-			nl->wait_frameno = 0;
-			nl->inppos = 0;
-#ifdef CONFIG_SBNI_MULTILINE
-			nl->master->stats.rx_errors++;
-			nl->master->stats.rx_missed_errors++;
-#else
-		        dev->stats.rx_errors++;
-			dev->stats.rx_missed_errors++;
-#endif
-		}
-			/* now skip all frames until is_first != 0 */
-	} else
-		frame_ok = skip_tail( dev->base_addr, framelen, crc );
-
-	if( is_first  &&  !frame_ok ) {
-		/*
-		 * Frame has been broken, but we had already stored
-		 * is_first... Drop entire packet.
-		 */
-		nl->wait_frameno = 0;
-#ifdef CONFIG_SBNI_MULTILINE
-		nl->master->stats.rx_errors++;
-		nl->master->stats.rx_crc_errors++;
-#else
-		dev->stats.rx_errors++;
-		dev->stats.rx_crc_errors++;
-#endif
-	}
-
-	return  frame_ok;
-}
-
-
-static inline void
-send_complete( struct net_device *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-#ifdef CONFIG_SBNI_MULTILINE
-	nl->master->stats.tx_packets++;
-	nl->master->stats.tx_bytes += nl->tx_buf_p->len;
-#else
-	dev->stats.tx_packets++;
-	dev->stats.tx_bytes += nl->tx_buf_p->len;
-#endif
-	dev_consume_skb_irq(nl->tx_buf_p);
-
-	nl->tx_buf_p = NULL;
-
-	nl->outpos = 0;
-	nl->state &= ~(FL_WAIT_ACK | FL_NEED_RESEND);
-	nl->framelen   = 0;
-}
-
-
-static void
-interpret_ack( struct net_device  *dev,  unsigned  ack )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	if( ack == FRAME_SENT_OK ) {
-		nl->state &= ~FL_NEED_RESEND;
-
-		if( nl->state & FL_WAIT_ACK ) {
-			nl->outpos += nl->framelen;
-
-			if( --nl->tx_frameno ) {
-				nl->framelen = min_t(unsigned int,
-						   nl->maxframe,
-						   nl->tx_buf_p->len - nl->outpos);
-			} else {
-				send_complete( dev );
-#ifdef CONFIG_SBNI_MULTILINE
-				netif_wake_queue( nl->master );
-#else
-				netif_wake_queue( dev );
-#endif
-			}
-		}
-	}
-
-	nl->state &= ~FL_WAIT_ACK;
-}
-
-
-/*
- * Glue received frame with previous fragments of packet.
- * Indicate packet when last frame would be accepted.
- */
-
-static int
-append_frame_to_pkt( struct net_device  *dev,  unsigned  framelen,  u32  crc )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	u8  *p;
-
-	if( nl->inppos + framelen  >  ETHER_MAX_LEN )
-		return  0;
-
-	if( !nl->rx_buf_p  &&  !(nl->rx_buf_p = get_rx_buf( dev )) )
-		return  0;
-
-	p = nl->rx_buf_p->data + nl->inppos;
-	insb( dev->base_addr + DAT, p, framelen );
-	if( calc_crc32( crc, p, framelen ) != CRC32_REMAINDER )
-		return  0;
-
-	nl->inppos += framelen - 4;
-	if( --nl->wait_frameno == 0 )		/* last frame received */
-		indicate_pkt( dev );
-
-	return  1;
-}
-
-
-/*
- * Prepare to start output on adapter.
- * Transmitter will be actually activated when marker is accepted.
- */
-
-static void
-prepare_to_send( struct sk_buff  *skb,  struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	unsigned int  len;
-
-	/* nl->tx_buf_p == NULL here! */
-	if( nl->tx_buf_p )
-		netdev_err(dev, "memory leak!\n");
-
-	nl->outpos = 0;
-	nl->state &= ~(FL_WAIT_ACK | FL_NEED_RESEND);
-
-	len = skb->len;
-	if( len < SBNI_MIN_LEN )
-		len = SBNI_MIN_LEN;
-
-	nl->tx_buf_p	= skb;
-	nl->tx_frameno	= DIV_ROUND_UP(len, nl->maxframe);
-	nl->framelen	= len < nl->maxframe  ?  len  :  nl->maxframe;
-
-	outb( inb( dev->base_addr + CSR0 ) | TR_REQ,  dev->base_addr + CSR0 );
-#ifdef CONFIG_SBNI_MULTILINE
-	netif_trans_update(nl->master);
-#else
-	netif_trans_update(dev);
-#endif
-}
-
-
-static void
-drop_xmit_queue( struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	if( nl->tx_buf_p ) {
-		dev_kfree_skb_any( nl->tx_buf_p );
-		nl->tx_buf_p = NULL;
-#ifdef CONFIG_SBNI_MULTILINE
-		nl->master->stats.tx_errors++;
-		nl->master->stats.tx_carrier_errors++;
-#else
-		dev->stats.tx_errors++;
-		dev->stats.tx_carrier_errors++;
-#endif
-	}
-
-	nl->tx_frameno	= 0;
-	nl->framelen	= 0;
-	nl->outpos	= 0;
-	nl->state &= ~(FL_WAIT_ACK | FL_NEED_RESEND);
-#ifdef CONFIG_SBNI_MULTILINE
-	netif_start_queue( nl->master );
-	netif_trans_update(nl->master);
-#else
-	netif_start_queue( dev );
-	netif_trans_update(dev);
-#endif
-}
-
-
-static void
-send_frame_header( struct net_device  *dev,  u32  *crc_p )
-{
-	struct net_local  *nl  = netdev_priv(dev);
-
-	u32  crc = *crc_p;
-	u32  len_field = nl->framelen + 6;	/* CRC + frameno + reserved */
-	u8   value;
-
-	if( nl->state & FL_NEED_RESEND )
-		len_field |= FRAME_RETRY;	/* non-first attempt... */
-
-	if( nl->outpos == 0 )
-		len_field |= FRAME_FIRST;
-
-	len_field |= (nl->state & FL_PREV_OK) ? FRAME_SENT_OK : FRAME_SENT_BAD;
-	outb( SBNI_SIG, dev->base_addr + DAT );
-
-	value = (u8) len_field;
-	outb( value, dev->base_addr + DAT );
-	crc = CRC32( value, crc );
-	value = (u8) (len_field >> 8);
-	outb( value, dev->base_addr + DAT );
-	crc = CRC32( value, crc );
-
-	outb( nl->tx_frameno, dev->base_addr + DAT );
-	crc = CRC32( nl->tx_frameno, crc );
-	outb( 0, dev->base_addr + DAT );
-	crc = CRC32( 0, crc );
-	*crc_p = crc;
-}
-
-
-/*
- * if frame tail not needed (incorrect number or received twice),
- * it won't store, but CRC will be calculated
- */
-
-static int
-skip_tail( unsigned int  ioaddr,  unsigned int  tail_len,  u32 crc )
-{
-	while( tail_len-- )
-		crc = CRC32( inb( ioaddr + DAT ), crc );
-
-	return  crc == CRC32_REMAINDER;
-}
-
-
-/*
- * Preliminary checks if frame header is correct, calculates its CRC
- * and split it to simple fields
- */
-
-static int
-check_fhdr( u32  ioaddr,  u32  *framelen,  u32  *frameno,  u32  *ack,
-	    u32  *is_first,  u32  *crc_p )
-{
-	u32  crc = *crc_p;
-	u8   value;
-
-	if( inb( ioaddr + DAT ) != SBNI_SIG )
-		return  0;
-
-	value = inb( ioaddr + DAT );
-	*framelen = (u32)value;
-	crc = CRC32( value, crc );
-	value = inb( ioaddr + DAT );
-	*framelen |= ((u32)value) << 8;
-	crc = CRC32( value, crc );
-
-	*ack = *framelen & FRAME_ACK_MASK;
-	*is_first = (*framelen & FRAME_FIRST) != 0;
-
-	if( (*framelen &= FRAME_LEN_MASK) < 6 ||
-	    *framelen > SBNI_MAX_FRAME - 3 )
-		return  0;
-
-	value = inb( ioaddr + DAT );
-	*frameno = (u32)value;
-	crc = CRC32( value, crc );
-
-	crc = CRC32( inb( ioaddr + DAT ), crc );	/* reserved byte */
-	*framelen -= 2;
-
-	*crc_p = crc;
-	return  1;
-}
-
-
-static struct sk_buff *
-get_rx_buf( struct net_device  *dev )
-{
-	/* +2 is to compensate for the alignment fixup below */
-	struct sk_buff  *skb = dev_alloc_skb( ETHER_MAX_LEN + 2 );
-	if( !skb )
-		return  NULL;
-
-	skb_reserve( skb, 2 );		/* Align IP on longword boundaries */
-	return  skb;
-}
-
-
-static void
-indicate_pkt( struct net_device  *dev )
-{
-	struct net_local  *nl  = netdev_priv(dev);
-	struct sk_buff    *skb = nl->rx_buf_p;
-
-	skb_put( skb, nl->inppos );
-
-#ifdef CONFIG_SBNI_MULTILINE
-	skb->protocol = eth_type_trans( skb, nl->master );
-	netif_rx( skb );
-	++nl->master->stats.rx_packets;
-	nl->master->stats.rx_bytes += nl->inppos;
-#else
-	skb->protocol = eth_type_trans( skb, dev );
-	netif_rx( skb );
-	++dev->stats.rx_packets;
-	dev->stats.rx_bytes += nl->inppos;
-#endif
-	nl->rx_buf_p = NULL;	/* protocol driver will clear this sk_buff */
-}
-
-
-/* -------------------------------------------------------------------------- */
-
-/*
- * Routine checks periodically wire activity and regenerates marker if
- * connect was inactive for a long time.
- */
-
-static void
-sbni_watchdog(struct timer_list *t)
-{
-	struct net_local   *nl  = from_timer(nl, t, watchdog);
-	struct net_device  *dev = nl->watchdog_dev;
-	unsigned long	   flags;
-	unsigned char	   csr0;
-
-	spin_lock_irqsave( &nl->lock, flags );
-
-	csr0 = inb( dev->base_addr + CSR0 );
-	if( csr0 & RC_CHK ) {
-
-		if( nl->timer_ticks ) {
-			if( csr0 & (RC_RDY | BU_EMP) )
-				/* receiving not active */
-				nl->timer_ticks--;
-		} else {
-			nl->in_stats.timeout_number++;
-			if( nl->delta_rxl )
-				timeout_change_level( dev );
-
-			outb( *(u_char *)&nl->csr1 | PR_RES,
-			      dev->base_addr + CSR1 );
-			csr0 = inb( dev->base_addr + CSR0 );
-		}
-	} else
-		nl->state &= ~FL_LINE_DOWN;
-
-	outb( csr0 | RC_CHK, dev->base_addr + CSR0 ); 
-
-	mod_timer(t, jiffies + SBNI_TIMEOUT);
-
-	spin_unlock_irqrestore( &nl->lock, flags );
-}
-
-
-static unsigned char  rxl_tab[] = {
-	0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x08,
-	0x0a, 0x0c, 0x0f, 0x16, 0x18, 0x1a, 0x1c, 0x1f
-};
-
-#define SIZE_OF_TIMEOUT_RXL_TAB 4
-static unsigned char  timeout_rxl_tab[] = {
-	0x03, 0x05, 0x08, 0x0b
-};
-
-/* -------------------------------------------------------------------------- */
-
-static void
-card_start( struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	nl->timer_ticks = CHANGE_LEVEL_START_TICKS;
-	nl->state &= ~(FL_WAIT_ACK | FL_NEED_RESEND);
-	nl->state |= FL_PREV_OK;
-
-	nl->inppos = nl->outpos = 0;
-	nl->wait_frameno = 0;
-	nl->tx_frameno	 = 0;
-	nl->framelen	 = 0;
-
-	outb( *(u_char *)&nl->csr1 | PR_RES, dev->base_addr + CSR1 );
-	outb( EN_INT, dev->base_addr + CSR0 );
-}
-
-/* -------------------------------------------------------------------------- */
-
-/* Receive level auto-selection */
-
-static void
-change_level( struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	if( nl->delta_rxl == 0 )	/* do not auto-negotiate RxL */
-		return;
-
-	if( nl->cur_rxl_index == 0 )
-		nl->delta_rxl = 1;
-	else if( nl->cur_rxl_index == 15 )
-		nl->delta_rxl = -1;
-	else if( nl->cur_rxl_rcvd < nl->prev_rxl_rcvd )
-		nl->delta_rxl = -nl->delta_rxl;
-
-	nl->csr1.rxl = rxl_tab[ nl->cur_rxl_index += nl->delta_rxl ];
-	inb( dev->base_addr + CSR0 );	/* needs for PCI cards */
-	outb( *(u8 *)&nl->csr1, dev->base_addr + CSR1 );
-
-	nl->prev_rxl_rcvd = nl->cur_rxl_rcvd;
-	nl->cur_rxl_rcvd  = 0;
-}
-
-
-static void
-timeout_change_level( struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	nl->cur_rxl_index = timeout_rxl_tab[ nl->timeout_rxl ];
-	if( ++nl->timeout_rxl >= 4 )
-		nl->timeout_rxl = 0;
-
-	nl->csr1.rxl = rxl_tab[ nl->cur_rxl_index ];
-	inb( dev->base_addr + CSR0 );
-	outb( *(unsigned char *)&nl->csr1, dev->base_addr + CSR1 );
-
-	nl->prev_rxl_rcvd = nl->cur_rxl_rcvd;
-	nl->cur_rxl_rcvd  = 0;
-}
-
-/* -------------------------------------------------------------------------- */
-
-/*
- *	Open/initialize the board. 
- */
-
-static int
-sbni_open( struct net_device  *dev )
-{
-	struct net_local	*nl = netdev_priv(dev);
-	struct timer_list	*w  = &nl->watchdog;
-
-	/*
-	 * For double ISA adapters within "common irq" mode, we have to
-	 * determine whether primary or secondary channel is initialized,
-	 * and set the irq handler only in first case.
-	 */
-	if( dev->base_addr < 0x400 ) {		/* ISA only */
-		struct net_device  **p = sbni_cards;
-		for( ;  *p  &&  p < sbni_cards + SBNI_MAX_NUM_CARDS;  ++p )
-			if( (*p)->irq == dev->irq &&
-			    ((*p)->base_addr == dev->base_addr + 4 ||
-			     (*p)->base_addr == dev->base_addr - 4) &&
-			    (*p)->flags & IFF_UP ) {
-
-				((struct net_local *) (netdev_priv(*p)))
-					->second = dev;
-				netdev_notice(dev, "using shared irq with %s\n",
-					      (*p)->name);
-				nl->state |= FL_SECONDARY;
-				goto  handler_attached;
-			}
-	}
-
-	if( request_irq(dev->irq, sbni_interrupt, IRQF_SHARED, dev->name, dev) ) {
-		netdev_err(dev, "unable to get IRQ %d\n", dev->irq);
-		return  -EAGAIN;
-	}
-
-handler_attached:
-
-	spin_lock( &nl->lock );
-	memset( &dev->stats, 0, sizeof(struct net_device_stats) );
-	memset( &nl->in_stats, 0, sizeof(struct sbni_in_stats) );
-
-	card_start( dev );
-
-	netif_start_queue( dev );
-
-	/* set timer watchdog */
-	nl->watchdog_dev = dev;
-	timer_setup(w, sbni_watchdog, 0);
-	w->expires	= jiffies + SBNI_TIMEOUT;
-	add_timer( w );
-   
-	spin_unlock( &nl->lock );
-	return 0;
-}
-
-
-static int
-sbni_close( struct net_device  *dev )
-{
-	struct net_local  *nl = netdev_priv(dev);
-
-	if( nl->second  &&  nl->second->flags & IFF_UP ) {
-		netdev_notice(dev, "Secondary channel (%s) is active!\n",
-			      nl->second->name);
-		return  -EBUSY;
-	}
-
-#ifdef CONFIG_SBNI_MULTILINE
-	if( nl->state & FL_SLAVE )
-		emancipate( dev );
-	else
-		while( nl->link )	/* it's master device! */
-			emancipate( nl->link );
-#endif
-
-	spin_lock( &nl->lock );
-
-	nl->second = NULL;
-	drop_xmit_queue( dev );	
-	netif_stop_queue( dev );
-   
-	del_timer( &nl->watchdog );
-
-	outb( 0, dev->base_addr + CSR0 );
-
-	if( !(nl->state & FL_SECONDARY) )
-		free_irq( dev->irq, dev );
-	nl->state &= FL_SECONDARY;
-
-	spin_unlock( &nl->lock );
-	return 0;
-}
-
-
-/*
-	Valid combinations in CSR0 (for probing):
-
-	VALID_DECODER	0000,0011,1011,1010
-
-				    	; 0   ; -
-				TR_REQ	; 1   ; +
-			TR_RDY	    	; 2   ; -
-			TR_RDY	TR_REQ	; 3   ; +
-		BU_EMP		    	; 4   ; +
-		BU_EMP	     	TR_REQ	; 5   ; +
-		BU_EMP	TR_RDY	    	; 6   ; -
-		BU_EMP	TR_RDY	TR_REQ	; 7   ; +
-	RC_RDY 		     		; 8   ; +
-	RC_RDY			TR_REQ	; 9   ; +
-	RC_RDY		TR_RDY		; 10  ; -
-	RC_RDY		TR_RDY	TR_REQ	; 11  ; -
-	RC_RDY	BU_EMP			; 12  ; -
-	RC_RDY	BU_EMP		TR_REQ	; 13  ; -
-	RC_RDY	BU_EMP	TR_RDY		; 14  ; -
-	RC_RDY	BU_EMP	TR_RDY	TR_REQ	; 15  ; -
-*/
-
-#define VALID_DECODER (2 + 8 + 0x10 + 0x20 + 0x80 + 0x100 + 0x200)
-
-
-static int
-sbni_card_probe( unsigned long  ioaddr )
-{
-	unsigned char  csr0;
-
-	csr0 = inb( ioaddr + CSR0 );
-	if( csr0 != 0xff  &&  csr0 != 0x00 ) {
-		csr0 &= ~EN_INT;
-		if( csr0 & BU_EMP )
-			csr0 |= EN_INT;
-      
-		if( VALID_DECODER & (1 << (csr0 >> 4)) )
-			return  0;
-	}
-   
-	return  -ENODEV;
-}
-
-/* -------------------------------------------------------------------------- */
-
-static int
-sbni_ioctl( struct net_device  *dev,  struct ifreq  *ifr,  int  cmd )
-{
-	struct net_local  *nl = netdev_priv(dev);
-	struct sbni_flags  flags;
-	int  error = 0;
-
-#ifdef CONFIG_SBNI_MULTILINE
-	struct net_device  *slave_dev;
-	char  slave_name[ 8 ];
-#endif
-  
-	switch( cmd ) {
-	case  SIOCDEVGETINSTATS :
-		if (copy_to_user( ifr->ifr_data, &nl->in_stats,
-					sizeof(struct sbni_in_stats) ))
-			error = -EFAULT;
-		break;
-
-	case  SIOCDEVRESINSTATS :
-		if (!capable(CAP_NET_ADMIN))
-			return  -EPERM;
-		memset( &nl->in_stats, 0, sizeof(struct sbni_in_stats) );
-		break;
-
-	case  SIOCDEVGHWSTATE :
-		flags.mac_addr	= *(u32 *)(dev->dev_addr + 3);
-		flags.rate	= nl->csr1.rate;
-		flags.slow_mode	= (nl->state & FL_SLOW_MODE) != 0;
-		flags.rxl	= nl->cur_rxl_index;
-		flags.fixed_rxl	= nl->delta_rxl == 0;
-
-		if (copy_to_user( ifr->ifr_data, &flags, sizeof flags ))
-			error = -EFAULT;
-		break;
-
-	case  SIOCDEVSHWSTATE :
-		if (!capable(CAP_NET_ADMIN))
-			return  -EPERM;
-
-		spin_lock( &nl->lock );
-		flags = *(struct sbni_flags*) &ifr->ifr_ifru;
-		if( flags.fixed_rxl ) {
-			nl->delta_rxl = 0;
-			nl->cur_rxl_index = flags.rxl;
-		} else {
-			nl->delta_rxl = DEF_RXL_DELTA;
-			nl->cur_rxl_index = DEF_RXL;
-		}
-
-		nl->csr1.rxl = rxl_tab[ nl->cur_rxl_index ];
-		nl->csr1.rate = flags.rate;
-		outb( *(u8 *)&nl->csr1 | PR_RES, dev->base_addr + CSR1 );
-		spin_unlock( &nl->lock );
-		break;
-
-#ifdef CONFIG_SBNI_MULTILINE
-
-	case  SIOCDEVENSLAVE :
-		if (!capable(CAP_NET_ADMIN))
-			return  -EPERM;
-
-		if (copy_from_user( slave_name, ifr->ifr_data, sizeof slave_name ))
-			return -EFAULT;
-		slave_dev = dev_get_by_name(&init_net, slave_name );
-		if( !slave_dev  ||  !(slave_dev->flags & IFF_UP) ) {
-			netdev_err(dev, "trying to enslave non-active device %s\n",
-				   slave_name);
-			if (slave_dev)
-				dev_put(slave_dev);
-			return  -EPERM;
-		}
-
-		return  enslave( dev, slave_dev );
-
-	case  SIOCDEVEMANSIPATE :
-		if (!capable(CAP_NET_ADMIN))
-			return  -EPERM;
-
-		return  emancipate( dev );
-
-#endif	/* CONFIG_SBNI_MULTILINE */
-
-	default :
-		return  -EOPNOTSUPP;
-	}
-
-	return  error;
-}
-
-
-#ifdef CONFIG_SBNI_MULTILINE
-
-static int
-enslave( struct net_device  *dev,  struct net_device  *slave_dev )
-{
-	struct net_local  *nl  = netdev_priv(dev);
-	struct net_local  *snl = netdev_priv(slave_dev);
-
-	if( nl->state & FL_SLAVE )	/* This isn't master or free device */
-		return  -EBUSY;
-
-	if( snl->state & FL_SLAVE )	/* That was already enslaved */
-		return  -EBUSY;
-
-	spin_lock( &nl->lock );
-	spin_lock( &snl->lock );
-
-	/* append to list */
-	snl->link = nl->link;
-	nl->link  = slave_dev;
-	snl->master = dev;
-	snl->state |= FL_SLAVE;
-
-	/* Summary statistics of MultiLine operation will be stored
-	   in master's counters */
-	memset( &slave_dev->stats, 0, sizeof(struct net_device_stats) );
-	netif_stop_queue( slave_dev );
-	netif_wake_queue( dev );	/* Now we are able to transmit */
-
-	spin_unlock( &snl->lock );
-	spin_unlock( &nl->lock );
-	netdev_notice(dev, "slave device (%s) attached\n", slave_dev->name);
-	return  0;
-}
-
-
-static int
-emancipate( struct net_device  *dev )
-{
-	struct net_local   *snl = netdev_priv(dev);
-	struct net_device  *p   = snl->master;
-	struct net_local   *nl  = netdev_priv(p);
-
-	if( !(snl->state & FL_SLAVE) )
-		return  -EINVAL;
-
-	spin_lock( &nl->lock );
-	spin_lock( &snl->lock );
-	drop_xmit_queue( dev );
-
-	/* exclude from list */
-	for(;;) {	/* must be in list */
-		struct net_local  *t = netdev_priv(p);
-		if( t->link == dev ) {
-			t->link = snl->link;
-			break;
-		}
-		p = t->link;
-	}
-
-	snl->link = NULL;
-	snl->master = dev;
-	snl->state &= ~FL_SLAVE;
-
-	netif_start_queue( dev );
-
-	spin_unlock( &snl->lock );
-	spin_unlock( &nl->lock );
-
-	dev_put( dev );
-	return  0;
-}
-
-#endif
-
-static void
-set_multicast_list( struct net_device  *dev )
-{
-	return;		/* sbni always operate in promiscuos mode */
-}
-
-
-#ifdef MODULE
-module_param_hw_array(io, int, ioport, NULL, 0);
-module_param_hw_array(irq, int, irq, NULL, 0);
-module_param_array(baud, int, NULL, 0);
-module_param_array(rxl, int, NULL, 0);
-module_param_array(mac, int, NULL, 0);
-module_param(skip_pci_probe, bool, 0);
-
-MODULE_LICENSE("GPL");
-
-
-int __init init_module( void )
-{
-	struct net_device  *dev;
-	int err;
-
-	while( num < SBNI_MAX_NUM_CARDS ) {
-		dev = alloc_netdev(sizeof(struct net_local), "sbni%d",
-				   NET_NAME_UNKNOWN, sbni_devsetup);
-		if( !dev)
-			break;
-
-		sprintf( dev->name, "sbni%d", num );
-
-		err = sbni_init(dev);
-		if (err) {
-			free_netdev(dev);
-			break;
-		}
-
-		if( register_netdev( dev ) ) {
-			release_region( dev->base_addr, SBNI_IO_EXTENT );
-			free_netdev( dev );
-			break;
-		}
-	}
-
-	return  *sbni_cards  ?  0  :  -ENODEV;
-}
-
-void
-cleanup_module(void)
-{
-	int i;
-
-	for (i = 0;  i < SBNI_MAX_NUM_CARDS;  ++i) {
-		struct net_device *dev = sbni_cards[i];
-		if (dev != NULL) {
-			unregister_netdev(dev);
-			release_region(dev->base_addr, SBNI_IO_EXTENT);
-			free_netdev(dev);
-		}
-	}
-}
-
-#else	/* MODULE */
-
-static int __init
-sbni_setup( char  *p )
-{
-	int  n, parm;
-
-	if( *p++ != '(' )
-		goto  bad_param;
-
-	for( n = 0, parm = 0;  *p  &&  n < 8; ) {
-		(*dest[ parm ])[ n ] = simple_strtoul( p, &p, 0 );
-		if( !*p  ||  *p == ')' )
-			return 1;
-		if( *p == ';' ) {
-			++p;
-			++n;
-			parm = 0;
-		} else if( *p++ != ',' ) {
-			break;
-		} else {
-			if( ++parm >= 5 )
-				break;
-		}
-	}
-bad_param:
-	pr_err("Error in sbni kernel parameter!\n");
-	return 0;
-}
-
-__setup( "sbni=", sbni_setup );
-
-#endif	/* MODULE */
-
-/* -------------------------------------------------------------------------- */
-
-static u32
-calc_crc32( u32  crc,  u8  *p,  u32  len )
-{
-	while( len-- )
-		crc = CRC32( *p++, crc );
-
-	return  crc;
-}
-
-static u32  crc32tab[] __attribute__ ((aligned(8))) = {
-	0xD202EF8D,  0xA505DF1B,  0x3C0C8EA1,  0x4B0BBE37,
-	0xD56F2B94,  0xA2681B02,  0x3B614AB8,  0x4C667A2E,
-	0xDCD967BF,  0xABDE5729,  0x32D70693,  0x45D03605,
-	0xDBB4A3A6,  0xACB39330,  0x35BAC28A,  0x42BDF21C,
-	0xCFB5FFE9,  0xB8B2CF7F,  0x21BB9EC5,  0x56BCAE53,
-	0xC8D83BF0,  0xBFDF0B66,  0x26D65ADC,  0x51D16A4A,
-	0xC16E77DB,  0xB669474D,  0x2F6016F7,  0x58672661,
-	0xC603B3C2,  0xB1048354,  0x280DD2EE,  0x5F0AE278,
-	0xE96CCF45,  0x9E6BFFD3,  0x0762AE69,  0x70659EFF,
-	0xEE010B5C,  0x99063BCA,  0x000F6A70,  0x77085AE6,
-	0xE7B74777,  0x90B077E1,  0x09B9265B,  0x7EBE16CD,
-	0xE0DA836E,  0x97DDB3F8,  0x0ED4E242,  0x79D3D2D4,
-	0xF4DBDF21,  0x83DCEFB7,  0x1AD5BE0D,  0x6DD28E9B,
-	0xF3B61B38,  0x84B12BAE,  0x1DB87A14,  0x6ABF4A82,
-	0xFA005713,  0x8D076785,  0x140E363F,  0x630906A9,
-	0xFD6D930A,  0x8A6AA39C,  0x1363F226,  0x6464C2B0,
-	0xA4DEAE1D,  0xD3D99E8B,  0x4AD0CF31,  0x3DD7FFA7,
-	0xA3B36A04,  0xD4B45A92,  0x4DBD0B28,  0x3ABA3BBE,
-	0xAA05262F,  0xDD0216B9,  0x440B4703,  0x330C7795,
-	0xAD68E236,  0xDA6FD2A0,  0x4366831A,  0x3461B38C,
-	0xB969BE79,  0xCE6E8EEF,  0x5767DF55,  0x2060EFC3,
-	0xBE047A60,  0xC9034AF6,  0x500A1B4C,  0x270D2BDA,
-	0xB7B2364B,  0xC0B506DD,  0x59BC5767,  0x2EBB67F1,
-	0xB0DFF252,  0xC7D8C2C4,  0x5ED1937E,  0x29D6A3E8,
-	0x9FB08ED5,  0xE8B7BE43,  0x71BEEFF9,  0x06B9DF6F,
-	0x98DD4ACC,  0xEFDA7A5A,  0x76D32BE0,  0x01D41B76,
-	0x916B06E7,  0xE66C3671,  0x7F6567CB,  0x0862575D,
-	0x9606C2FE,  0xE101F268,  0x7808A3D2,  0x0F0F9344,
-	0x82079EB1,  0xF500AE27,  0x6C09FF9D,  0x1B0ECF0B,
-	0x856A5AA8,  0xF26D6A3E,  0x6B643B84,  0x1C630B12,
-	0x8CDC1683,  0xFBDB2615,  0x62D277AF,  0x15D54739,
-	0x8BB1D29A,  0xFCB6E20C,  0x65BFB3B6,  0x12B88320,
-	0x3FBA6CAD,  0x48BD5C3B,  0xD1B40D81,  0xA6B33D17,
-	0x38D7A8B4,  0x4FD09822,  0xD6D9C998,  0xA1DEF90E,
-	0x3161E49F,  0x4666D409,  0xDF6F85B3,  0xA868B525,
-	0x360C2086,  0x410B1010,  0xD80241AA,  0xAF05713C,
-	0x220D7CC9,  0x550A4C5F,  0xCC031DE5,  0xBB042D73,
-	0x2560B8D0,  0x52678846,  0xCB6ED9FC,  0xBC69E96A,
-	0x2CD6F4FB,  0x5BD1C46D,  0xC2D895D7,  0xB5DFA541,
-	0x2BBB30E2,  0x5CBC0074,  0xC5B551CE,  0xB2B26158,
-	0x04D44C65,  0x73D37CF3,  0xEADA2D49,  0x9DDD1DDF,
-	0x03B9887C,  0x74BEB8EA,  0xEDB7E950,  0x9AB0D9C6,
-	0x0A0FC457,  0x7D08F4C1,  0xE401A57B,  0x930695ED,
-	0x0D62004E,  0x7A6530D8,  0xE36C6162,  0x946B51F4,
-	0x19635C01,  0x6E646C97,  0xF76D3D2D,  0x806A0DBB,
-	0x1E0E9818,  0x6909A88E,  0xF000F934,  0x8707C9A2,
-	0x17B8D433,  0x60BFE4A5,  0xF9B6B51F,  0x8EB18589,
-	0x10D5102A,  0x67D220BC,  0xFEDB7106,  0x89DC4190,
-	0x49662D3D,  0x3E611DAB,  0xA7684C11,  0xD06F7C87,
-	0x4E0BE924,  0x390CD9B2,  0xA0058808,  0xD702B89E,
-	0x47BDA50F,  0x30BA9599,  0xA9B3C423,  0xDEB4F4B5,
-	0x40D06116,  0x37D75180,  0xAEDE003A,  0xD9D930AC,
-	0x54D13D59,  0x23D60DCF,  0xBADF5C75,  0xCDD86CE3,
-	0x53BCF940,  0x24BBC9D6,  0xBDB2986C,  0xCAB5A8FA,
-	0x5A0AB56B,  0x2D0D85FD,  0xB404D447,  0xC303E4D1,
-	0x5D677172,  0x2A6041E4,  0xB369105E,  0xC46E20C8,
-	0x72080DF5,  0x050F3D63,  0x9C066CD9,  0xEB015C4F,
-	0x7565C9EC,  0x0262F97A,  0x9B6BA8C0,  0xEC6C9856,
-	0x7CD385C7,  0x0BD4B551,  0x92DDE4EB,  0xE5DAD47D,
-	0x7BBE41DE,  0x0CB97148,  0x95B020F2,  0xE2B71064,
-	0x6FBF1D91,  0x18B82D07,  0x81B17CBD,  0xF6B64C2B,
-	0x68D2D988,  0x1FD5E91E,  0x86DCB8A4,  0xF1DB8832,
-	0x616495A3,  0x1663A535,  0x8F6AF48F,  0xF86DC419,
-	0x660951BA,  0x110E612C,  0x88073096,  0xFF000000
-};
-
diff --git a/drivers/net/wan/sbni.h b/drivers/net/wan/sbni.h
deleted file mode 100644
index 84264510a8ed..000000000000
--- a/drivers/net/wan/sbni.h
+++ /dev/null
@@ -1,147 +0,0 @@
-/* sbni.h:  definitions for a Granch SBNI12 driver, version 5.0.0
- * Written 2001 Denis I.Timofeev (timofeev@granch.ru)
- * This file is distributed under the GNU GPL
- */
-
-#ifndef SBNI_H
-#define SBNI_H
-
-#ifdef SBNI_DEBUG
-#define DP( A ) A
-#else
-#define DP( A )
-#endif
-
-
-/* We don't have official vendor id yet... */
-#define SBNI_PCI_VENDOR 	0x55 
-#define SBNI_PCI_DEVICE 	0x9f
-
-#define ISA_MODE 0x00
-#define PCI_MODE 0x01
-
-#define	SBNI_IO_EXTENT	4
-
-enum sbni_reg {
-	CSR0 = 0,
-	CSR1 = 1,
-	DAT  = 2
-};
-
-/* CSR0 mapping */
-enum {
-	BU_EMP = 0x02,
-	RC_CHK = 0x04,
-	CT_ZER = 0x08,
-	TR_REQ = 0x10,
-	TR_RDY = 0x20,
-	EN_INT = 0x40,
-	RC_RDY = 0x80
-};
-
-
-/* CSR1 mapping */
-#define PR_RES 0x80
-
-struct sbni_csr1 {
-#ifdef __LITTLE_ENDIAN_BITFIELD
-	u8 rxl	: 5;
-	u8 rate	: 2;
-	u8 	: 1;
-#else
-	u8 	: 1;
-	u8 rate	: 2;
-	u8 rxl	: 5;
-#endif
-};
-
-/* fields in frame header */
-#define FRAME_ACK_MASK  (unsigned short)0x7000
-#define FRAME_LEN_MASK  (unsigned short)0x03FF
-#define FRAME_FIRST     (unsigned short)0x8000
-#define FRAME_RETRY     (unsigned short)0x0800
-
-#define FRAME_SENT_BAD  (unsigned short)0x4000
-#define FRAME_SENT_OK   (unsigned short)0x3000
-
-
-/* state flags */
-enum {
-	FL_WAIT_ACK    = 0x01,
-	FL_NEED_RESEND = 0x02,
-	FL_PREV_OK     = 0x04,
-	FL_SLOW_MODE   = 0x08,
-	FL_SECONDARY   = 0x10,
-#ifdef CONFIG_SBNI_MULTILINE
-	FL_SLAVE       = 0x20,
-#endif
-	FL_LINE_DOWN   = 0x40
-};
-
-
-enum {
-	DEFAULT_IOBASEADDR = 0x210,
-	DEFAULT_INTERRUPTNUMBER = 5,
-	DEFAULT_RATE = 0,
-	DEFAULT_FRAME_LEN = 1012
-};
-
-#define DEF_RXL_DELTA	-1
-#define DEF_RXL		0xf
-
-#define SBNI_SIG 0x5a
-
-#define	SBNI_MIN_LEN	60	/* Shortest Ethernet frame without FCS */
-#define SBNI_MAX_FRAME	1023
-#define ETHER_MAX_LEN	1518
-
-#define SBNI_TIMEOUT	(HZ/10)
-
-#define TR_ERROR_COUNT	32
-#define CHANGE_LEVEL_START_TICKS 4
-
-#define SBNI_MAX_NUM_CARDS	16
-
-/* internal SBNI-specific statistics */
-struct sbni_in_stats {
-	u32	all_rx_number;
-	u32	bad_rx_number;
-	u32	timeout_number;
-	u32	all_tx_number;
-	u32	resend_tx_number;
-};
-
-/* SBNI ioctl params */
-#define SIOCDEVGETINSTATS 	SIOCDEVPRIVATE
-#define SIOCDEVRESINSTATS 	SIOCDEVPRIVATE+1
-#define SIOCDEVGHWSTATE   	SIOCDEVPRIVATE+2
-#define SIOCDEVSHWSTATE   	SIOCDEVPRIVATE+3
-#define SIOCDEVENSLAVE  	SIOCDEVPRIVATE+4
-#define SIOCDEVEMANSIPATE  	SIOCDEVPRIVATE+5
-
-
-/* data packet for SIOCDEVGHWSTATE/SIOCDEVSHWSTATE ioctl requests */
-struct sbni_flags {
-	u32	rxl		: 4;
-	u32	rate		: 2;
-	u32	fixed_rxl	: 1;
-	u32	slow_mode	: 1;
-	u32	mac_addr	: 24;
-};
-
-/*
- * CRC-32 stuff
- */
-#define CRC32(c,crc) (crc32tab[((size_t)(crc) ^ (c)) & 0xff] ^ (((crc) >> 8) & 0x00FFFFFF))
-      /* CRC generator 0xEDB88320 */
-      /* CRC remainder 0x2144DF1C */
-      /* CRC initial value 0x00000000 */
-#define CRC32_REMAINDER 0x2144DF1C
-#define CRC32_INITIAL 0x00000000
-
-#ifndef __initdata
-#define __initdata
-#endif
-
-#endif
-
diff --git a/include/net/Space.h b/include/net/Space.h
index 93fd6caa4bad..08ca9cef0213 100644
--- a/include/net/Space.h
+++ b/include/net/Space.h
@@ -18,6 +18,3 @@ struct net_device *cops_probe(int unit);
 
 /* Fibre Channel adapters */
 int iph5526_probe(struct net_device *dev);
-
-/* SBNI adapters */
-int sbni_probe(int unit);
-- 
2.29.2

[RFC 11/13] [net-next] wan: hostess_sv11: use module_init/module_exit helpers

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

This is one of very few drivers using the old init_module/cleanup_module
function names. Change it over to the modern method.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/wan/hostess_sv11.c | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wan/hostess_sv11.c b/drivers/net/wan/hostess_sv11.c
index 6c05c4c8914a..59808fba23c2 100644
--- a/drivers/net/wan/hostess_sv11.c
+++ b/drivers/net/wan/hostess_sv11.c
@@ -338,15 +338,17 @@ MODULE_DESCRIPTION("Modular driver for the Comtrol Hostess SV11");
 
 static struct z8530_dev *sv11_unit;
 
-int init_module(void)
+static int sv11_module_init(void)
 {
 	if ((sv11_unit = sv11_init(io, irq)) == NULL)
 		return -ENODEV;
 	return 0;
 }
+module_init(sv11_module_init);
 
-void cleanup_module(void)
+static void sv11_module_cleanup(void)
 {
 	if (sv11_unit)
 		sv11_shutdown(sv11_unit);
 }
+module_exit(sv11_module_cleanup);
-- 
2.29.2

[RFC 12/13] [net-next] ethernet: isa: convert to module_init/module_exit

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

There are a couple of ISA ethernet drivers that use the old
init_module/cleanup_module function names for the main entry
points, practically nothing else uses those.

Change them to the documented method with module_init()
and module_exit() markers next to static functions.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/ethernet/3com/3c515.c     | 3 ++-
 drivers/net/ethernet/8390/ne.c        | 3 ++-
 drivers/net/ethernet/8390/smc-ultra.c | 9 ++++-----
 drivers/net/ethernet/8390/wd.c        | 7 ++++---
 drivers/net/ethernet/amd/lance.c      | 6 ++++--
 drivers/net/ethernet/amd/ni65.c       | 6 ++++--
 drivers/net/ethernet/cirrus/cs89x0.c  | 7 ++++---
 drivers/net/ethernet/smsc/smc9194.c   | 6 ++++--
 8 files changed, 28 insertions(+), 19 deletions(-)

diff --git a/drivers/net/ethernet/3com/3c515.c b/drivers/net/ethernet/3com/3c515.c
index 47b4215bb93b..8d90fed5d33e 100644
--- a/drivers/net/ethernet/3com/3c515.c
+++ b/drivers/net/ethernet/3com/3c515.c
@@ -407,7 +407,7 @@ MODULE_PARM_DESC(max_interrupt_work, "3c515 maximum events handled per interrupt
 /* we will need locking (and refcounting) if we ever use it for more */
 static LIST_HEAD(root_corkscrew_dev);
 
-int init_module(void)
+static int corkscrew_init_module(void)
 {
 	int found = 0;
 	if (debug >= 0)
@@ -416,6 +416,7 @@ int init_module(void)
 		found++;
 	return found ? 0 : -ENODEV;
 }
+module_init(corkscrew_init_module);
 
 #else
 struct net_device *tc515_probe(int unit)
diff --git a/drivers/net/ethernet/8390/ne.c b/drivers/net/ethernet/8390/ne.c
index d0bbe2180b9e..53660bc8d6ff 100644
--- a/drivers/net/ethernet/8390/ne.c
+++ b/drivers/net/ethernet/8390/ne.c
@@ -923,7 +923,7 @@ static void __init ne_add_devices(void)
 }
 
 #ifdef MODULE
-int __init init_module(void)
+static int __init ne_init(void)
 {
 	int retval;
 	ne_add_devices();
@@ -940,6 +940,7 @@ int __init init_module(void)
 	ne_loop_rm_unreg(0);
 	return retval;
 }
+module_init(ne_init);
 #else /* MODULE */
 static int __init ne_init(void)
 {
diff --git a/drivers/net/ethernet/8390/smc-ultra.c b/drivers/net/ethernet/8390/smc-ultra.c
index 3fe3b4dfa7c5..0600e05512da 100644
--- a/drivers/net/ethernet/8390/smc-ultra.c
+++ b/drivers/net/ethernet/8390/smc-ultra.c
@@ -522,7 +522,6 @@ static void ultra_pio_input(struct net_device *dev, int count,
 	/* We know skbuffs are padded to at least word alignment. */
 	insw(ioaddr + IOPD, buf, (count+1)>>1);
 }
-
 static void ultra_pio_output(struct net_device *dev, int count,
 							const unsigned char *buf, const int start_page)
 {
@@ -572,8 +571,7 @@ MODULE_LICENSE("GPL");
 
 /* This is set up so that only a single autoprobe takes place per call.
 ISA device autoprobes on a running machine are not recommended. */
-int __init
-init_module(void)
+static int __init ultra_init_module(void)
 {
 	struct net_device *dev;
 	int this_dev, found = 0;
@@ -600,6 +598,7 @@ init_module(void)
 		return 0;
 	return -ENXIO;
 }
+module_init(ultra_init_module);
 
 static void cleanup_card(struct net_device *dev)
 {
@@ -613,8 +612,7 @@ static void cleanup_card(struct net_device *dev)
 	iounmap(ei_status.mem);
 }
 
-void __exit
-cleanup_module(void)
+static void __exit ultra_cleanup_module(void)
 {
 	int this_dev;
 
@@ -627,4 +625,5 @@ cleanup_module(void)
 		}
 	}
 }
+module_exit(ultra_cleanup_module);
 #endif /* MODULE */
diff --git a/drivers/net/ethernet/8390/wd.c b/drivers/net/ethernet/8390/wd.c
index c834123560f1..263a942d81fa 100644
--- a/drivers/net/ethernet/8390/wd.c
+++ b/drivers/net/ethernet/8390/wd.c
@@ -519,7 +519,7 @@ MODULE_LICENSE("GPL");
 /* This is set up so that only a single autoprobe takes place per call.
 ISA device autoprobes on a running machine are not recommended. */
 
-int __init init_module(void)
+static int __init wd_init_module(void)
 {
 	struct net_device *dev;
 	int this_dev, found = 0;
@@ -548,6 +548,7 @@ int __init init_module(void)
 		return 0;
 	return -ENXIO;
 }
+module_init(wd_init_module);
 
 static void cleanup_card(struct net_device *dev)
 {
@@ -556,8 +557,7 @@ static void cleanup_card(struct net_device *dev)
 	iounmap(ei_status.mem);
 }
 
-void __exit
-cleanup_module(void)
+static void __exit wd_cleanup_module(void)
 {
 	int this_dev;
 
@@ -570,4 +570,5 @@ cleanup_module(void)
 		}
 	}
 }
+module_exit(wd_cleanup_module);
 #endif /* MODULE */
diff --git a/drivers/net/ethernet/amd/lance.c b/drivers/net/ethernet/amd/lance.c
index aff44241988c..997f9f2f84f4 100644
--- a/drivers/net/ethernet/amd/lance.c
+++ b/drivers/net/ethernet/amd/lance.c
@@ -327,7 +327,7 @@ MODULE_PARM_DESC(dma, "LANCE/PCnet ISA DMA channel (ignored for some devices)");
 MODULE_PARM_DESC(irq, "LANCE/PCnet IRQ number (ignored for some devices)");
 MODULE_PARM_DESC(lance_debug, "LANCE/PCnet debug level (0-7)");
 
-int __init init_module(void)
+static int __init lance_init_module(void)
 {
 	struct net_device *dev;
 	int this_dev, found = 0;
@@ -356,6 +356,7 @@ int __init init_module(void)
 		return 0;
 	return -ENXIO;
 }
+module_init(lance_init_module);
 
 static void cleanup_card(struct net_device *dev)
 {
@@ -368,7 +369,7 @@ static void cleanup_card(struct net_device *dev)
 	kfree(lp);
 }
 
-void __exit cleanup_module(void)
+static void __exit lance_cleanup_module(void)
 {
 	int this_dev;
 
@@ -381,6 +382,7 @@ void __exit cleanup_module(void)
 		}
 	}
 }
+module_exit(lance_cleanup_module);
 #endif /* MODULE */
 MODULE_LICENSE("GPL");
 
diff --git a/drivers/net/ethernet/amd/ni65.c b/drivers/net/ethernet/amd/ni65.c
index c38edf6f03a3..da9ca21fecf7 100644
--- a/drivers/net/ethernet/amd/ni65.c
+++ b/drivers/net/ethernet/amd/ni65.c
@@ -1230,18 +1230,20 @@ MODULE_PARM_DESC(irq, "ni6510 IRQ number (ignored for some cards)");
 MODULE_PARM_DESC(io, "ni6510 I/O base address");
 MODULE_PARM_DESC(dma, "ni6510 ISA DMA channel (ignored for some cards)");
 
-int __init init_module(void)
+static int __init ni65_init_module(void)
 {
  	dev_ni65 = ni65_probe(-1);
 	return PTR_ERR_OR_ZERO(dev_ni65);
 }
+module_init(ni65_init_module);
 
-void __exit cleanup_module(void)
+static void __exit ni65_cleanup_module(void)
 {
  	unregister_netdev(dev_ni65);
  	cleanup_card(dev_ni65);
  	free_netdev(dev_ni65);
 }
+module_exit(ni65_cleanup_module);
 #endif /* MODULE */
 
 MODULE_LICENSE("GPL");
diff --git a/drivers/net/ethernet/cirrus/cs89x0.c b/drivers/net/ethernet/cirrus/cs89x0.c
index 3b08cd943b7b..d0c4c8b7a15a 100644
--- a/drivers/net/ethernet/cirrus/cs89x0.c
+++ b/drivers/net/ethernet/cirrus/cs89x0.c
@@ -1753,7 +1753,7 @@ MODULE_LICENSE("GPL");
  * (hw or software util)
  */
 
-int __init init_module(void)
+static int __init cs89x0_isa_init_module(void)
 {
 	struct net_device *dev;
 	struct net_local *lp;
@@ -1823,9 +1823,9 @@ int __init init_module(void)
 	free_netdev(dev);
 	return ret;
 }
+module_init(cs89x0_isa_init_module);
 
-void __exit
-cleanup_module(void)
+static void __exit cs89x0_isa_cleanup_module(void)
 {
 	struct net_local *lp = netdev_priv(dev_cs89x0);
 
@@ -1835,6 +1835,7 @@ cleanup_module(void)
 	release_region(dev_cs89x0->base_addr, NETCARD_IO_EXTENT);
 	free_netdev(dev_cs89x0);
 }
+module_exit(cs89x0_isa_cleanup_module);
 #endif /* MODULE */
 #endif /* CONFIG_CS89x0_ISA */
 
diff --git a/drivers/net/ethernet/smsc/smc9194.c b/drivers/net/ethernet/smsc/smc9194.c
index 4b2330deed47..d7a394d4b460 100644
--- a/drivers/net/ethernet/smsc/smc9194.c
+++ b/drivers/net/ethernet/smsc/smc9194.c
@@ -1508,7 +1508,7 @@ MODULE_PARM_DESC(io, "SMC 99194 I/O base address");
 MODULE_PARM_DESC(irq, "SMC 99194 IRQ number");
 MODULE_PARM_DESC(ifport, "SMC 99194 interface port (0-default, 1-TP, 2-AUI)");
 
-int __init init_module(void)
+static int __init smc_init_module(void)
 {
 	if (io == 0)
 		printk(KERN_WARNING
@@ -1518,13 +1518,15 @@ int __init init_module(void)
 	devSMC9194 = smc_init(-1);
 	return PTR_ERR_OR_ZERO(devSMC9194);
 }
+module_init(smc_init_module);
 
-void __exit cleanup_module(void)
+static void __exit smc_cleanup_module(void)
 {
 	unregister_netdev(devSMC9194);
 	free_irq(devSMC9194->irq, devSMC9194);
 	release_region(devSMC9194->base_addr, SMC_IO_EXTENT);
 	free_netdev(devSMC9194);
 }
+module_exit(smc_cleanup_module);
 
 #endif /* MODULE */
-- 
2.29.2

[RFC 13/13] [net-next] 8390: xsurf100: avoid including lib8390.c

[Arnd Bergmann]

From: Arnd Bergmann <arnd@arndb.de>

This driver always warns about unused functions because it includes
an file that it doesn't actually need:

In file included from drivers/net/ethernet/8390/xsurf100.c:48:
drivers/net/ethernet/8390/lib8390.c:995:27: error: '____alloc_ei_netdev' defined but not used [-Werror=unused-function]
  995 | static struct net_device *____alloc_ei_netdev(int size)
      |                           ^~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:957:13: error: '__ei_set_multicast_list' defined but not used [-Werror=unused-function]
  957 | static void __ei_set_multicast_list(struct net_device *dev)
      |             ^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:857:33: error: '__ei_get_stats' defined but not used [-Werror=unused-function]
  857 | static struct net_device_stats *__ei_get_stats(struct net_device *dev)
      |                                 ^~~~~~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:512:13: error: '__ei_poll' defined but not used [-Werror=unused-function]
  512 | static void __ei_poll(struct net_device *dev)
      |             ^~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:303:20: error: '__ei_start_xmit' defined but not used [-Werror=unused-function]
  303 | static netdev_tx_t __ei_start_xmit(struct sk_buff *skb,
      |                    ^~~~~~~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:257:13: error: '__ei_tx_timeout' defined but not used [-Werror=unused-function]
  257 | static void __ei_tx_timeout(struct net_device *dev, unsigned int txqueue)
      |             ^~~~~~~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:233:12: error: '__ei_close' defined but not used [-Werror=unused-function]
  233 | static int __ei_close(struct net_device *dev)
      |            ^~~~~~~~~~
drivers/net/ethernet/8390/lib8390.c:204:12: error: '__ei_open' defined but not used [-Werror=unused-function]
  204 | static int __ei_open(struct net_device *dev)
      |            ^~~~~~~~~

Use the normal library module instead and call the NS8390p_init()
function.

Fixes: 861928f4e60e ("net-next: New ax88796 platform driver for Amiga X-Surf 100 Zorro board (m68k)")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
 drivers/net/ethernet/8390/Makefile   | 2 +-
 drivers/net/ethernet/8390/xsurf100.c | 7 ++-----
 2 files changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile
index 85c83c566ec6..304897d5f0f9 100644
--- a/drivers/net/ethernet/8390/Makefile
+++ b/drivers/net/ethernet/8390/Makefile
@@ -16,5 +16,5 @@ obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o 8390.o
 obj-$(CONFIG_STNIC) += stnic.o 8390.o
 obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
 obj-$(CONFIG_WD80x3) += wd.o 8390.o
-obj-$(CONFIG_XSURF100) += xsurf100.o
+obj-$(CONFIG_XSURF100) += xsurf100.o 8390.o
 obj-$(CONFIG_ZORRO8390) += zorro8390.o
diff --git a/drivers/net/ethernet/8390/xsurf100.c b/drivers/net/ethernet/8390/xsurf100.c
index e2c963821ffe..11d5d43e7202 100644
--- a/drivers/net/ethernet/8390/xsurf100.c
+++ b/drivers/net/ethernet/8390/xsurf100.c
@@ -42,10 +42,7 @@
 /* Ensure we have our RCR base value */
 #define AX88796_PLATFORM
 
-static unsigned char version[] =
-		"ax88796.c: Copyright 2005,2007 Simtec Electronics\n";
-
-#include "lib8390.c"
+#include "8390.h"
 
 /* from ne.c */
 #define NE_CMD		EI_SHIFT(0x00)
@@ -232,7 +229,7 @@ static void xs100_block_output(struct net_device *dev, int count,
 		if (jiffies - dma_start > 2 * HZ / 100) {	/* 20ms */
 			netdev_warn(dev, "timeout waiting for Tx RDC.\n");
 			ei_local->reset_8390(dev);
-			ax_NS8390_init(dev, 1);
+			NS8390p_init(dev, 1);
 			break;
 		}
 	}
-- 
2.29.2

Re: [RFC 01/13] [net-next] bcmgenet: remove call to netdev_boot_setup_check

[Florian Fainelli]

On 5/15/2021 3:13 PM, Arnd Bergmann wrote:
> From: Arnd Bergmann <arnd@arndb.de>
> 
> The driver has never used the netdev->{irq,base_addr,mem_start}
> members, so this call is completely unnecessary.
> 
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Acked-by: Florian Fainelli <f.fainelli@gmail.com>
-- 
Florian

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Maciej W. Rozycki]

On Sun, 16 May 2021, Arnd Bergmann wrote:

> For the ISA drivers, there is usually no way to probe multiple devices
> at boot time other than the netdev= arguments, so all that logic is left
> in place for the moment, but centralized in a single file that only gets
> included in the kernel build if one or more of the drivers are built-in.

 As I recall at least some ISA drivers did probe multiple interfaces in 
their monolithic configuration; I used a configuration with as many as 
five ne2k clones for a bridge machine for a fairly large network (~300 
machines) and as I recall it required no command-line parameters (but then 
it was some 25 years ago, so I may well not remember correctly anymore).  
It may have been with ISA PnP though (damn!).

 For modular drivers it was deemed too dangerous, for obvious reasons, and 
explicit parameters were the only way.

> * Most of ISA drivers could be trivially converted to use the module_init()
>   entry point, which would slightly change the command line syntax and
>   still support a single device of that type, but not more than one. We
>   could decide that this is fine, as few users remain that have any of
>   these devices, let alone more than one.
> 
> * Alternatively, the fact that the ISA drivers have never been cleaned
>   up can be seen as an indication that there isn't really much remaining
>   interest in them. We could move them to drivers/staging along with the
>   consolidated contents of drivers/net/Space.c and see if anyone still
>   uses them and eventually remove the ones that nobody has.

 I have a 3c509b interface in active use (although in the EISA mode, so no 
need for weird probing, but it can be reconfigured), and I have an ne2k 
clone in storage, so I could do some run-time verification if there is no 
one else available.  I'll see if I can do some driver polishing for these 
devices, but given the number of other tasks on my table this is somewhat 
low priority for me.

  Maciej

Re: [RFC 13/13] [net-next] 8390: xsurf100: avoid including lib8390.c

[Finn Thain]

On Sun, 16 May 2021, Arnd Bergmann wrote:

> From: Arnd Bergmann <arnd@arndb.de>
> 
> This driver always warns about unused functions because it includes
> an file that it doesn't actually need:
> 

I don't think you can omit #include "lib8390.c" here without changing 
driver behaviour, because of the macros in effect.

I think this change would need some actual testing unless you can show 
that the module binary does not change.

Re: [RFC 13/13] [net-next] 8390: xsurf100: avoid including lib8390.c

[Geert Uytterhoeven]

On Sun, May 16, 2021 at 6:24 AM Finn Thain <fthain@telegraphics.com.au> wrote:
> On Sun, 16 May 2021, Arnd Bergmann wrote:
> > From: Arnd Bergmann <arnd@arndb.de>
> >
> > This driver always warns about unused functions because it includes
> > an file that it doesn't actually need:
>
> I don't think you can omit #include "lib8390.c" here without changing
> driver behaviour, because of the macros in effect.
>
> I think this change would need some actual testing unless you can show
> that the module binary does not change.

Michael posted a similar but different patch a while ago, involving
calling ax_NS8390_reinit():
https://lore.kernel.org/linux-m68k/1528604559-972-3-git-send-email-schmitzmic@gmail.com/

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Arnd Bergmann]

On Sun, May 16, 2021 at 2:06 AM Maciej W. Rozycki <macro@orcam.me.uk> wrote:
>
> On Sun, 16 May 2021, Arnd Bergmann wrote:
>
> > For the ISA drivers, there is usually no way to probe multiple devices
> > at boot time other than the netdev= arguments, so all that logic is left
> > in place for the moment, but centralized in a single file that only gets
> > included in the kernel build if one or more of the drivers are built-in.
>
>  As I recall at least some ISA drivers did probe multiple interfaces in
> their monolithic configuration; I used a configuration with as many as
> five ne2k clones for a bridge machine for a fairly large network (~300
> machines) and as I recall it required no command-line parameters (but then
> it was some 25 years ago, so I may well not remember correctly anymore).
> It may have been with ISA PnP though (damn!).
>
>  For modular drivers it was deemed too dangerous, for obvious reasons, and
> explicit parameters were the only way.

I did use two ne2k compatible pre-PnP cards in a router, by loading two
copies of the same driver module, and I'm fairly sure that would still work,
but it's obviously not how it was meant to be used. ;-)

To clarify: the code drivers/net/Space.c logic can probe these drivers
both with and without explicit configuration. Using the netdev= arguments
will result in reliable assignment of device names and prevent drivers
from poking ports that may be used by other devices, but drivers can
also implement their own device detection, in case of
drivers/net/ethernet/8390/ne.c, it can find devices at up to six addresses:
static unsigned int netcard_portlist[] __initdata = {
    0x300, 0x280, 0x320, 0x340, 0x360, 0x380, 0
};

> > * Most of ISA drivers could be trivially converted to use the module_init()
> >   entry point, which would slightly change the command line syntax and
> >   still support a single device of that type, but not more than one. We
> >   could decide that this is fine, as few users remain that have any of
> >   these devices, let alone more than one.
> >
> > * Alternatively, the fact that the ISA drivers have never been cleaned
> >   up can be seen as an indication that there isn't really much remaining
> >   interest in them. We could move them to drivers/staging along with the
> >   consolidated contents of drivers/net/Space.c and see if anyone still
> >   uses them and eventually remove the ones that nobody has.
>
>  I have a 3c509b interface in active use (although in the EISA mode, so no
> need for weird probing, but it can be reconfigured),

The 3c509 driver already doesn't use the drivers/net/Space.c probing,
Marc Zyngier addressed this when he added EISA support in 2003.
It also supports multiple non-PnP cards with module parameters
as well as pre-standard jumperless autoconfiguration. My only change
to this driver was to remove a few lines of dead code that I guess Marc
missed at the time.

I probably should have listed the drivers that still use Space.c after
my series. Here is the list I'm talking about:

3com:
    3c515/corkscrew: supports PnP mode, ignores command line and
        module parameters but scans for devices on all ports
8390:
   wd80x3: supports module parameters up to four cards, no PnP
   smc-ultra: supports up to four devices with module parameters, plus PnP
   ne2k/iosa: supports up to four devices with module parameters, plus PnP
amd
   lance: supports up to eight devices with module parameters, no PnP
   ni65: supports only one device as loadable module, no PnP
smsc
   smc9194: supports only one device as loadable module, no PnP
cirrus
   cs89x0 (supports only one device as loadable module, plus custom
        PnP-like probing in built-in mode)

> and I have an ne2k clone in storage, so I could do some run-time
> verification if there is no one else available.  I'll see if I can do some driver
> polishing for these devices, but given the number of other tasks on my
> table this is somewhat low priority for me.

I don't think it's necessary to validate the changes I did to the
ne2k driver specifically, though it might be nice to see that I didn't
break the overall logic in Space.c.

        Arnd

Re: [RFC 13/13] [net-next] 8390: xsurf100: avoid including lib8390.c

[Arnd Bergmann]

On Sun, May 16, 2021 at 11:04 AM Geert Uytterhoeven
<geert@linux-m68k.org> wrote:
>
> On Sun, May 16, 2021 at 6:24 AM Finn Thain <fthain@telegraphics.com.au> wrote:
> > On Sun, 16 May 2021, Arnd Bergmann wrote:
> > > From: Arnd Bergmann <arnd@arndb.de>
> > >
> > > This driver always warns about unused functions because it includes
> > > an file that it doesn't actually need:
> >
> > I don't think you can omit #include "lib8390.c" here without changing
> > driver behaviour, because of the macros in effect.
> >
> > I think this change would need some actual testing unless you can show
> > that the module binary does not change.
>
> Michael posted a similar but different patch a while ago, involving
> calling ax_NS8390_reinit():
> https://lore.kernel.org/linux-m68k/1528604559-972-3-git-send-email-schmitzmic@gmail.com/

Ah nice. As far as I can tell, the two versions are functionally equivalent
based on my reading of the port accessors, but he probably tested his
version, so I'll drop mine from this series. Nothing else depends on this
one, I just included it since it was an obvious thing to fix.

        Arnd

Re: [RFC 06/13] [net-next] m68k: remove legacy probing

[Geert Uytterhoeven]

Hi Arnd,

CC linux-m68k

On Sun, May 16, 2021 at 12:14 AM Arnd Bergmann <arnd@kernel.org> wrote:
> From: Arnd Bergmann <arnd@arndb.de>
>
> There are six m68k specific drivers that use the legacy probe method
> in drivers/net/Space.c. However, all of these only support a single
> device, and they completely ignore the command line settings from
> netdev_boot_setup_check, so there is really no point at all.
>
> Aside from sun3_82586, these already have a module_init function that
> can be used for built-in mode as well, simply by removing the #ifdef.
>
> Note that the 82596 driver was previously used on ISA as well, but
> that got dropped long ago.

> Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Looks all good to me, so
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
but I don't have any of the hardware to test.

> ---
>  drivers/net/Space.c                      | 25 +-----------------------
>  drivers/net/ethernet/8390/apne.c         | 11 ++---------
>  drivers/net/ethernet/amd/atarilance.c    | 11 ++---------
>  drivers/net/ethernet/amd/mvme147.c       | 16 ++++++---------
>  drivers/net/ethernet/amd/sun3lance.c     | 19 ++++++------------
>  drivers/net/ethernet/i825xx/82596.c      | 24 ++++++-----------------
>  drivers/net/ethernet/i825xx/sun3_82586.c | 17 +++++++---------
>  include/net/Space.h                      |  6 ------
>  8 files changed, 30 insertions(+), 99 deletions(-)
>
> diff --git a/drivers/net/Space.c b/drivers/net/Space.c
> index 9f573f7ded3c..a03559f23295 100644
> --- a/drivers/net/Space.c
> +++ b/drivers/net/Space.c
> @@ -80,34 +80,12 @@ static struct devprobe2 isa_probes[] __initdata = {
>  #ifdef CONFIG_CS89x0_ISA
>         {cs89x0_probe, 0},
>  #endif
> -#if defined(CONFIG_MVME16x_NET) || defined(CONFIG_BVME6000_NET)        /* Intel */
> -       {i82596_probe, 0},                                      /* I82596 */
> -#endif
>  #ifdef CONFIG_NI65
>         {ni65_probe, 0},
>  #endif
>         {NULL, 0},
>  };
>
> -static struct devprobe2 m68k_probes[] __initdata = {
> -#ifdef CONFIG_ATARILANCE       /* Lance-based Atari ethernet boards */
> -       {atarilance_probe, 0},
> -#endif
> -#ifdef CONFIG_SUN3LANCE         /* sun3 onboard Lance chip */
> -       {sun3lance_probe, 0},
> -#endif
> -#ifdef CONFIG_SUN3_82586        /* sun3 onboard Intel 82586 chip */
> -       {sun3_82586_probe, 0},
> -#endif
> -#ifdef CONFIG_APNE             /* A1200 PCMCIA NE2000 */
> -       {apne_probe, 0},
> -#endif
> -#ifdef CONFIG_MVME147_NET      /* MVME147 internal Ethernet */
> -       {mvme147lance_probe, 0},
> -#endif
> -       {NULL, 0},
> -};
> -
>  /* Unified ethernet device probe, segmented per architecture and
>   * per bus interface. This drives the legacy devices only for now.
>   */
> @@ -119,8 +97,7 @@ static void __init ethif_probe2(int unit)
>         if (base_addr == 1)
>                 return;
>
> -       (void)(probe_list2(unit, m68k_probes, base_addr == 0) &&
> -               probe_list2(unit, isa_probes, base_addr == 0));
> +       probe_list2(unit, isa_probes, base_addr == 0);
>  }
>
>  /*  Statically configured drivers -- order matters here. */
> diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
> index fe6c834c422e..da1ae37a9d73 100644
> --- a/drivers/net/ethernet/8390/apne.c
> +++ b/drivers/net/ethernet/8390/apne.c
> @@ -75,7 +75,6 @@
>  #define NESM_STOP_PG   0x80    /* Last page +1 of RX ring */
>
>
> -struct net_device * __init apne_probe(int unit);
>  static int apne_probe1(struct net_device *dev, int ioaddr);
>
>  static void apne_reset_8390(struct net_device *dev);
> @@ -120,7 +119,7 @@ static u32 apne_msg_enable;
>  module_param_named(msg_enable, apne_msg_enable, uint, 0444);
>  MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
>
> -struct net_device * __init apne_probe(int unit)
> +static struct net_device * __init apne_probe(void)
>  {
>         struct net_device *dev;
>         struct ei_device *ei_local;
> @@ -150,10 +149,6 @@ struct net_device * __init apne_probe(int unit)
>         dev = alloc_ei_netdev();
>         if (!dev)
>                 return ERR_PTR(-ENOMEM);
> -       if (unit >= 0) {
> -               sprintf(dev->name, "eth%d", unit);
> -               netdev_boot_setup_check(dev);
> -       }
>         ei_local = netdev_priv(dev);
>         ei_local->msg_enable = apne_msg_enable;
>
> @@ -554,12 +549,11 @@ static irqreturn_t apne_interrupt(int irq, void *dev_id)
>      return IRQ_HANDLED;
>  }
>
> -#ifdef MODULE
>  static struct net_device *apne_dev;
>
>  static int __init apne_module_init(void)
>  {
> -       apne_dev = apne_probe(-1);
> +       apne_dev = apne_probe();
>         return PTR_ERR_OR_ZERO(apne_dev);
>  }
>
> @@ -579,7 +573,6 @@ static void __exit apne_module_exit(void)
>  }
>  module_init(apne_module_init);
>  module_exit(apne_module_exit);
> -#endif
>
>  static int init_pcmcia(void)
>  {
> diff --git a/drivers/net/ethernet/amd/atarilance.c b/drivers/net/ethernet/amd/atarilance.c
> index c1eab916438f..83012a1ef3cf 100644
> --- a/drivers/net/ethernet/amd/atarilance.c
> +++ b/drivers/net/ethernet/amd/atarilance.c
> @@ -367,7 +367,7 @@ static void *slow_memcpy( void *dst, const void *src, size_t len )
>  }
>
>
> -struct net_device * __init atarilance_probe(int unit)
> +struct net_device * __init atarilance_probe(void)
>  {
>         int i;
>         static int found;
> @@ -382,10 +382,6 @@ struct net_device * __init atarilance_probe(int unit)
>         dev = alloc_etherdev(sizeof(struct lance_private));
>         if (!dev)
>                 return ERR_PTR(-ENOMEM);
> -       if (unit >= 0) {
> -               sprintf(dev->name, "eth%d", unit);
> -               netdev_boot_setup_check(dev);
> -       }
>
>         for( i = 0; i < N_LANCE_ADDR; ++i ) {
>                 if (lance_probe1( dev, &lance_addr_list[i] )) {
> @@ -1137,13 +1133,11 @@ static int lance_set_mac_address( struct net_device *dev, void *addr )
>         return 0;
>  }
>
> -
> -#ifdef MODULE
>  static struct net_device *atarilance_dev;
>
>  static int __init atarilance_module_init(void)
>  {
> -       atarilance_dev = atarilance_probe(-1);
> +       atarilance_dev = atarilance_probe();
>         return PTR_ERR_OR_ZERO(atarilance_dev);
>  }
>
> @@ -1155,4 +1149,3 @@ static void __exit atarilance_module_exit(void)
>  }
>  module_init(atarilance_module_init);
>  module_exit(atarilance_module_exit);
> -#endif /* MODULE */
> diff --git a/drivers/net/ethernet/amd/mvme147.c b/drivers/net/ethernet/amd/mvme147.c
> index 3f2e4cdd0b83..da97fccea9ea 100644
> --- a/drivers/net/ethernet/amd/mvme147.c
> +++ b/drivers/net/ethernet/amd/mvme147.c
> @@ -68,7 +68,7 @@ static const struct net_device_ops lance_netdev_ops = {
>  };
>
>  /* Initialise the one and only on-board 7990 */
> -struct net_device * __init mvme147lance_probe(int unit)
> +static struct net_device * __init mvme147lance_probe(void)
>  {
>         struct net_device *dev;
>         static int called;
> @@ -86,9 +86,6 @@ struct net_device * __init mvme147lance_probe(int unit)
>         if (!dev)
>                 return ERR_PTR(-ENOMEM);
>
> -       if (unit >= 0)
> -               sprintf(dev->name, "eth%d", unit);
> -
>         /* Fill the dev fields */
>         dev->base_addr = (unsigned long)MVME147_LANCE_BASE;
>         dev->netdev_ops = &lance_netdev_ops;
> @@ -179,22 +176,21 @@ static int m147lance_close(struct net_device *dev)
>         return 0;
>  }
>
> -#ifdef MODULE
>  MODULE_LICENSE("GPL");
>
>  static struct net_device *dev_mvme147_lance;
> -int __init init_module(void)
> +static int __init m147lance_init(void)
>  {
> -       dev_mvme147_lance = mvme147lance_probe(-1);
> +       dev_mvme147_lance = mvme147lance_probe();
>         return PTR_ERR_OR_ZERO(dev_mvme147_lance);
>  }
> +module_init(m147lance_init);
>
> -void __exit cleanup_module(void)
> +static void __exit m147lance_exit(void)
>  {
>         struct m147lance_private *lp = netdev_priv(dev_mvme147_lance);
>         unregister_netdev(dev_mvme147_lance);
>         free_pages(lp->ram, 3);
>         free_netdev(dev_mvme147_lance);
>  }
> -
> -#endif /* MODULE */
> +module_exit(m147lance_exit);
> diff --git a/drivers/net/ethernet/amd/sun3lance.c b/drivers/net/ethernet/amd/sun3lance.c
> index 00ae1081254d..73724b082bdb 100644
> --- a/drivers/net/ethernet/amd/sun3lance.c
> +++ b/drivers/net/ethernet/amd/sun3lance.c
> @@ -245,7 +245,7 @@ static void set_multicast_list( struct net_device *dev );
>
>  /************************* End of Prototypes **************************/
>
> -struct net_device * __init sun3lance_probe(int unit)
> +static struct net_device * __init sun3lance_probe(void)
>  {
>         struct net_device *dev;
>         static int found;
> @@ -272,10 +272,6 @@ struct net_device * __init sun3lance_probe(int unit)
>         dev = alloc_etherdev(sizeof(struct lance_private));
>         if (!dev)
>                 return ERR_PTR(-ENOMEM);
> -       if (unit >= 0) {
> -               sprintf(dev->name, "eth%d", unit);
> -               netdev_boot_setup_check(dev);
> -       }
>
>         if (!lance_probe(dev))
>                 goto out;
> @@ -924,17 +920,16 @@ static void set_multicast_list( struct net_device *dev )
>  }
>
>
> -#ifdef MODULE
> -
>  static struct net_device *sun3lance_dev;
>
> -int __init init_module(void)
> +static int __init sun3lance_init(void)
>  {
> -       sun3lance_dev = sun3lance_probe(-1);
> +       sun3lance_dev = sun3lance_probe();
>         return PTR_ERR_OR_ZERO(sun3lance_dev);
>  }
> +module_init(sun3lance_init);
>
> -void __exit cleanup_module(void)
> +static void __exit sun3lance_cleanup(void)
>  {
>         unregister_netdev(sun3lance_dev);
>  #ifdef CONFIG_SUN3
> @@ -942,6 +937,4 @@ void __exit cleanup_module(void)
>  #endif
>         free_netdev(sun3lance_dev);
>  }
> -
> -#endif /* MODULE */
> -
> +module_exit(sun3lance_cleanup);
> diff --git a/drivers/net/ethernet/i825xx/82596.c b/drivers/net/ethernet/i825xx/82596.c
> index fc8c7cd67471..b8a40146b895 100644
> --- a/drivers/net/ethernet/i825xx/82596.c
> +++ b/drivers/net/ethernet/i825xx/82596.c
> @@ -1110,9 +1110,6 @@ static void print_eth(unsigned char *add, char *str)
>                add, add + 6, add, add[12], add[13], str);
>  }
>
> -static int io = 0x300;
> -static int irq = 10;
> -
>  static const struct net_device_ops i596_netdev_ops = {
>         .ndo_open               = i596_open,
>         .ndo_stop               = i596_close,
> @@ -1123,7 +1120,7 @@ static const struct net_device_ops i596_netdev_ops = {
>         .ndo_validate_addr      = eth_validate_addr,
>  };
>
> -struct net_device * __init i82596_probe(int unit)
> +static struct net_device * __init i82596_probe(void)
>  {
>         struct net_device *dev;
>         int i;
> @@ -1140,14 +1137,6 @@ struct net_device * __init i82596_probe(int unit)
>         if (!dev)
>                 return ERR_PTR(-ENOMEM);
>
> -       if (unit >= 0) {
> -               sprintf(dev->name, "eth%d", unit);
> -               netdev_boot_setup_check(dev);
> -       } else {
> -               dev->base_addr = io;
> -               dev->irq = irq;
> -       }
> -
>  #ifdef ENABLE_MVME16x_NET
>         if (MACH_IS_MVME16x) {
>                 if (mvme16x_config & MVME16x_CONFIG_NO_ETHERNET) {
> @@ -1515,22 +1504,22 @@ static void set_multicast_list(struct net_device *dev)
>         }
>  }
>
> -#ifdef MODULE
>  static struct net_device *dev_82596;
>
>  static int debug = -1;
>  module_param(debug, int, 0);
>  MODULE_PARM_DESC(debug, "i82596 debug mask");
>
> -int __init init_module(void)
> +static int __init i82596_init(void)
>  {
>         if (debug >= 0)
>                 i596_debug = debug;
> -       dev_82596 = i82596_probe(-1);
> +       dev_82596 = i82596_probe();
>         return PTR_ERR_OR_ZERO(dev_82596);
>  }
> +module_init(i82596_init);
>
> -void __exit cleanup_module(void)
> +static void __exit i82596_cleanup(void)
>  {
>         unregister_netdev(dev_82596);
>  #ifdef __mc68000__
> @@ -1544,5 +1533,4 @@ void __exit cleanup_module(void)
>         free_page ((u32)(dev_82596->mem_start));
>         free_netdev(dev_82596);
>  }
> -
> -#endif                         /* MODULE */
> +module_exit(i82596_cleanup);
> diff --git a/drivers/net/ethernet/i825xx/sun3_82586.c b/drivers/net/ethernet/i825xx/sun3_82586.c
> index 4564ee02c95f..893e0ddcb611 100644
> --- a/drivers/net/ethernet/i825xx/sun3_82586.c
> +++ b/drivers/net/ethernet/i825xx/sun3_82586.c
> @@ -29,6 +29,7 @@ static int rfdadd = 0; /* rfdadd=1 may be better for 8K MEM cards */
>  static int fifo=0x8;   /* don't change */
>
>  #include <linux/kernel.h>
> +#include <linux/module.h>
>  #include <linux/string.h>
>  #include <linux/errno.h>
>  #include <linux/ioport.h>
> @@ -276,7 +277,7 @@ static void alloc586(struct net_device *dev)
>         memset((char *)p->scb,0,sizeof(struct scb_struct));
>  }
>
> -struct net_device * __init sun3_82586_probe(int unit)
> +static int __init sun3_82586_probe(void)
>  {
>         struct net_device *dev;
>         unsigned long ioaddr;
> @@ -291,25 +292,20 @@ struct net_device * __init sun3_82586_probe(int unit)
>                 break;
>
>         default:
> -               return ERR_PTR(-ENODEV);
> +               return -ENODEV;
>         }
>
>         if (found)
> -               return ERR_PTR(-ENODEV);
> +               return -ENODEV;
>
>         ioaddr = (unsigned long)ioremap(IE_OBIO, SUN3_82586_TOTAL_SIZE);
>         if (!ioaddr)
> -               return ERR_PTR(-ENOMEM);
> +               return -ENOMEM;
>         found = 1;
>
>         dev = alloc_etherdev(sizeof(struct priv));
>         if (!dev)
>                 goto out;
> -       if (unit >= 0) {
> -               sprintf(dev->name, "eth%d", unit);
> -               netdev_boot_setup_check(dev);
> -       }
> -
>         dev->irq = IE_IRQ;
>         dev->base_addr = ioaddr;
>         err = sun3_82586_probe1(dev, ioaddr);
> @@ -326,8 +322,9 @@ struct net_device * __init sun3_82586_probe(int unit)
>         free_netdev(dev);
>  out:
>         iounmap((void __iomem *)ioaddr);
> -       return ERR_PTR(err);
> +       return err;
>  }
> +module_init(sun3_82586_probe);
>
>  static const struct net_device_ops sun3_82586_netdev_ops = {
>         .ndo_open               = sun3_82586_open,
> diff --git a/include/net/Space.h b/include/net/Space.h
> index e30e7a70ea99..93fd6caa4bad 100644
> --- a/include/net/Space.h
> +++ b/include/net/Space.h
> @@ -8,16 +8,10 @@ struct net_device *ultra_probe(int unit);
>  struct net_device *wd_probe(int unit);
>  struct net_device *ne_probe(int unit);
>  struct net_device *fmv18x_probe(int unit);
> -struct net_device *i82596_probe(int unit);
>  struct net_device *ni65_probe(int unit);
>  struct net_device *sonic_probe(int unit);
>  struct net_device *smc_init(int unit);
> -struct net_device *atarilance_probe(int unit);
> -struct net_device *sun3lance_probe(int unit);
> -struct net_device *sun3_82586_probe(int unit);
> -struct net_device *apne_probe(int unit);
>  struct net_device *cs89x0_probe(int unit);
> -struct net_device *mvme147lance_probe(int unit);
>  struct net_device *tc515_probe(int unit);
>  struct net_device *lance_probe(int unit);
>  struct net_device *cops_probe(int unit);

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Paul Gortmaker]

[[RFC 00/13] [net-next] drivers/net/Space.c cleanup] On 16/05/2021 (Sun 00:13) Arnd Bergmann wrote:

> From: Arnd Bergmann <arnd@arndb.de>

[...]

> * Alternatively, the fact that the ISA drivers have never been cleaned
>   up can be seen as an indication that there isn't really much remaining
>   interest in them. We could move them to drivers/staging along with the
>   consolidated contents of drivers/net/Space.c and see if anyone still
>   uses them and eventually remove the ones that nobody has.
>   I can see that Paul Gortmaker removed a number of less common ISA
>   ethernet drivers in 2013, but at the time left these because they
>   were possibly still relevant.

It was a thin/remote possibility, even then:  From v3.9-rc1~139^2~288

  In theory, it is possible that someone could still be running one of these
  12+ year old P3 machines and want 3.9+ bleeding edge kernels (but unlikely).
  In light of the above (remote) possibility, we can defer the removal of some
  ISA network drivers that were highly popular and well tested.  Typically
  that means the stuff more from the mid to late '90s, some with ISA PnP
  support, like the 3c509, the wd/SMC 8390 based stuff, PCnet/lance etc.

Now those 12y old machines are 20y old, and bleeding edge for this discussion
will be the the v5.14+ kernel.

Leaving the more popular cards was a concession to making progress vs.
having the whole cleanup blocked by individuals who haven't yet realized
that using ancient hardware is best done (only done?) with ancient kernels.

Maybe things are better now; people are putting more consideration to
the future of the kernel, rather than clinging to times long past?
We've since managed to delete several complete old arch dirs; which I
had previously thought impossible.  I couldn't even git rid of the x86
EISA support code six years ago.[1]

I'd be willing to do a "Phase 2" of 930d52c012b8 ISA net delete;  I'm
not sure the bounce through stable on the way out does much other than
muddy the git history.  I'd be tempted to just propose the individual
deletes and see where that goes....

Paul.
--

[1] https://lwn.net/Articles/630115/

> 
> * If we end up moving the cops localtalk driver to staging, support
>   for localtalk devices (though probably not appletalk over ethernet)
>   can arguably meet the same fate.
> 
> If someone wants to work on those follow-ups or thinks they are a
> good idea, let me know, otherwise I'd leave it at this cleanup.
> 
>        Arnd
> 
> Arnd Bergmann (13):
>   [net-next] bcmgenet: remove call to netdev_boot_setup_check
>   [net-next] natsemi: sonic: stop calling netdev_boot_setup_check
>   [net-next] appletalk: ltpc: remove static probing
>   [net-next] 3c509: stop calling netdev_boot_setup_check
>   [net-next] cs89x0: rework driver configuration
>   [net-next] m68k: remove legacy probing
>   [net-next] move netdev_boot_setup into Space.c
>   [net-next] make legacy ISA probe optional
>   [net-next] wan: remove stale Kconfig entries
>   [net-next] wan: remove sbni/granch driver
>   [net-next] wan: hostess_sv11: use module_init/module_exit helpers
>   [net-next] ethernet: isa: convert to module_init/module_exit
>   [net-next] 8390: xsurf100: avoid including lib8390.c
> 
>  .../admin-guide/kernel-parameters.txt         |    2 -
>  drivers/net/Kconfig                           |    7 +
>  drivers/net/Makefile                          |    3 +-
>  drivers/net/Space.c                           |  178 +-
>  drivers/net/appletalk/Kconfig                 |    4 +-
>  drivers/net/appletalk/ltpc.c                  |    7 +-
>  drivers/net/ethernet/3com/3c509.c             |    3 -
>  drivers/net/ethernet/3com/3c515.c             |    3 +-
>  drivers/net/ethernet/3com/Kconfig             |    1 +
>  drivers/net/ethernet/8390/Kconfig             |    3 +
>  drivers/net/ethernet/8390/Makefile            |    2 +-
>  drivers/net/ethernet/8390/apne.c              |   11 +-
>  drivers/net/ethernet/8390/ne.c                |    5 +-
>  drivers/net/ethernet/8390/smc-ultra.c         |    9 +-
>  drivers/net/ethernet/8390/wd.c                |    7 +-
>  drivers/net/ethernet/8390/xsurf100.c          |    7 +-
>  drivers/net/ethernet/amd/Kconfig              |    2 +
>  drivers/net/ethernet/amd/atarilance.c         |   11 +-
>  drivers/net/ethernet/amd/lance.c              |    6 +-
>  drivers/net/ethernet/amd/mvme147.c            |   16 +-
>  drivers/net/ethernet/amd/ni65.c               |    6 +-
>  drivers/net/ethernet/amd/sun3lance.c          |   19 +-
>  .../net/ethernet/broadcom/genet/bcmgenet.c    |    2 -
>  drivers/net/ethernet/cirrus/Kconfig           |   27 +-
>  drivers/net/ethernet/cirrus/cs89x0.c          |   31 +-
>  drivers/net/ethernet/i825xx/82596.c           |   24 +-
>  drivers/net/ethernet/i825xx/sun3_82586.c      |   17 +-
>  drivers/net/ethernet/natsemi/jazzsonic.c      |    2 -
>  drivers/net/ethernet/natsemi/xtsonic.c        |    1 -
>  drivers/net/ethernet/smsc/Kconfig             |    1 +
>  drivers/net/ethernet/smsc/smc9194.c           |    6 +-
>  drivers/net/wan/Kconfig                       |   51 -
>  drivers/net/wan/Makefile                      |    1 -
>  drivers/net/wan/hostess_sv11.c                |    6 +-
>  drivers/net/wan/sbni.c                        | 1638 -----------------
>  drivers/net/wan/sbni.h                        |  147 --
>  include/linux/netdevice.h                     |   13 -
>  include/net/Space.h                           |   10 -
>  net/core/dev.c                                |  125 --
>  net/ethernet/eth.c                            |    2 -
>  40 files changed, 259 insertions(+), 2157 deletions(-)
>  delete mode 100644 drivers/net/wan/sbni.c
>  delete mode 100644 drivers/net/wan/sbni.h
> 
> -- 
> 2.29.2
> 
> Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
> Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
> Cc: "David S. Miller" <davem@davemloft.net>
> Cc: Jakub Kicinski <kuba@kernel.org>
> Cc: Doug Berger <opendmb@gmail.com>
> Cc: Florian Fainelli <f.fainelli@gmail.com>
> Cc: Sam Creasey <sammy@sammy.net>
> Cc: Geert Uytterhoeven <geert@linux-m68k.org>
> Cc: Finn Thain <fthain@telegraphics.com.au>
> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
> Cc: Andrew Lunn <andrew@lunn.ch>
> Cc: Alexei Starovoitov <ast@kernel.org>
> Cc: Eric Dumazet <edumazet@google.com>
> Cc: Andrii Nakryiko <andriin@fb.com>
> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
> Cc: netdev@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: bcm-kernel-feedback-list@broadcom.com

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Maciej W. Rozycki]

On Mon, 17 May 2021, Paul Gortmaker wrote:

> Leaving the more popular cards was a concession to making progress vs.
> having the whole cleanup blocked by individuals who haven't yet realized
> that using ancient hardware is best done (only done?) with ancient kernels.

 Hmm, it depends on what you want to achieve, although I think it will be 
fair if you require anyone caring about old hardware to keep any relevant 
code base, such as drivers, board support, etc. up to date as our internal 
interfaces evolve.  Otherwise if it works, then I fail to see a reason to 
remove it just because you can.

> Maybe things are better now; people are putting more consideration to
> the future of the kernel, rather than clinging to times long past?
> We've since managed to delete several complete old arch dirs; which I
> had previously thought impossible.  I couldn't even git rid of the x86
> EISA support code six years ago.[1]

 Heh, that machine I raised my objection for is now back in service, after 
a failure of its industrial PSU and the installation of a replacement one 
(which was a bit of a challenge to track down), serving the maintenance of 
the defxx driver for the DEFEA (EISA) variant of the DEC FDDI network 
adapter:

platform eisa.0: Probing EISA bus 0
eisa 00:00: EISA: Mainboard AEI0401 detected
eisa 00:05: EISA: slot 5: DEC3002 detected
defxx: v1.12 2021/03/10  Lawrence V. Stefani and others
00:05: DEFEA at I/O addr = 0x5000, IRQ = 10, Hardware addr = 00-00-f8-c8-b3-b6
00:05: registered as fddi0
eisa 00:06: EISA: slot 6: NPI0303 detected
eisa 00:08: EISA: slot 8: TCM5094 detected
eth0: 3c5x9 found at 0x8000, 10baseT port, address 00:a0:24:b6:8b:db, IRQ 12.
platform eisa.0: EISA: Detected 3 cards

I just need to upgrade it with more DRAM (256MiB supported; not too bad 
for an i486) so that it runs a tad more smoothly.  An alternative would be 
switching to an EISA Alpha machine, however I don't have any at the moment 
and chasing one would be a bit of an issue.

 FAOD I keep getting contacted about the FDDI stuff as it remains in use 
in various industrial and scientific installations and the typical use 
case nowadays is getting whatever old gear, which has fallen apart, they 
have used to communicate with their equipment over FDDI with a modern 
Linux machine, preferably running out of the box with one of the readily 
available distributions, and one of those FDDI cards (normally the PCI 
variant though), which are reasonably available still.

> I'd be willing to do a "Phase 2" of 930d52c012b8 ISA net delete;  I'm
> not sure the bounce through stable on the way out does much other than
> muddy the git history.  I'd be tempted to just propose the individual
> deletes and see where that goes....

 Sounds fair to me.

  Maciej

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Arnd Bergmann]

On Mon, May 17, 2021 at 4:38 PM Paul Gortmaker
<paul.gortmaker@windriver.com> wrote:
> > From: Arnd Bergmann <arnd@arndb.de>
>
> I'd be willing to do a "Phase 2" of 930d52c012b8 ISA net delete;  I'm
> not sure the bounce through stable on the way out does much other than
> muddy the git history.  I'd be tempted to just propose the individual
> deletes and see where that goes....

I think the main benefit of going through drivers/staging would be that
it could be done somewhat more aggressively by moving more of the
presumed-unused hardware out at once, and waiting for media
coverage to wake up any remaining users. Then again, reverting
a removal isn't that different from reverting the move to staging.

If we do it one driver at a time, a good start might be the ones that
don't already have support for probing multiple devices in a loadable
module (ni65,smc9194, cs89x0-isa, cops, ltpc), which would let us
kill off drivers/net/Space.c by always using the module_init() logic.
These are all non-ISAPnP devices, and a second step could be
to remove support for all non-PNP devices (lance, wd80x3,
corkscrew and maybe the ISA WAN devices).

Unless we can agree to remove CONFIG_ISA completely, it's probably
best to leave ISA support for those drivers that also work on PCI, EISA
or m68k hardware, as those have the best chance to still get tested.
3c509 is probably the best maintained, given that it's the only network
driver that got converted to isa_register_driver() from the linux-2.0
style static probing. 3c515 has the distinction of being the only
remaining 100mbit one, and ne2k is obviously the one that one can
still find on ebay or the parent's attic.

       Arnd

Re: [RFC 00/13] [net-next] drivers/net/Space.c cleanup

[Finn Thain]

On Mon, 17 May 2021, Paul Gortmaker wrote:

> Leaving the more popular cards was a concession to making progress vs. 
> having the whole cleanup blocked by individuals who haven't yet realized 
> that using ancient hardware is best done (only done?) with ancient 
> kernels.
> 

By extension, using ancient kernels is best done with ancient userland. 
And now the time has come to remove all the 'compat' nonsense.

Oh, wait, all of that old software seems to be riddled with bugs and 
vulnerabilities.

And who would have thought that all those developers writing new code for 
emulators and their users were holding up "progress"?

> Maybe things are better now; people are putting more consideration to
> the future of the kernel, rather than clinging to times long past?

If you've been doing engineering for a while you'll start to notice a 
pattern: old designs that work get reused. That's partly why the latest 
silicon contains ancient logic blocks.

When that changes, perhaps we can talk about "progress"...