* [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable
@ 2019-12-12 13:00 Srinivas Neeli
2020-02-10 11:48 ` Michal Simek
0 siblings, 1 reply; 4+ messages in thread
From: Srinivas Neeli @ 2019-12-12 13:00 UTC (permalink / raw)
To: a.zummo, alexandre.belloni, michal.simek, sgoud, shubhraj
Cc: linux-rtc, linux-arm-kernel, linux-kernel, git, Srinivas Neeli
Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
clear the alarm interrupt status bit immediately after the interrupt is
triggered.This is due to the sticky nature of the alarm interrupt status
register. The alarm interrupt status register can be cleared only after
the second counter outruns the set alarm value. To fix multiple spurious
interrupts, disable alarm interrupt in the handler and clear the status
bit before enabling the alarm interrupt.
Fixes: 11143c19eb57 ("rtc: add xilinx zynqmp rtc driver")
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
---
drivers/rtc/rtc-zynqmp.c | 29 ++++++++++++++++++++++++-----
1 file changed, 24 insertions(+), 5 deletions(-)
diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
index 5786866c09e9..d311e3ef1f21 100644
--- a/drivers/rtc/rtc-zynqmp.c
+++ b/drivers/rtc/rtc-zynqmp.c
@@ -38,6 +38,8 @@
#define RTC_CALIB_DEF 0x198233
#define RTC_CALIB_MASK 0x1FFFFF
+#define RTC_ALRM_MASK BIT(1)
+#define RTC_MSEC 1000
struct xlnx_rtc_dev {
struct rtc_device *rtc;
@@ -124,11 +126,28 @@ static int xlnx_rtc_alarm_irq_enable(struct device *dev, u32 enabled)
{
struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
- if (enabled)
+ unsigned int status;
+ ulong timeout;
+
+ timeout = jiffies + msecs_to_jiffies(RTC_MSEC);
+
+ if (enabled) {
+ while (1) {
+ status = readl(xrtcdev->reg_base + RTC_INT_STS);
+ if (!((status & RTC_ALRM_MASK) == RTC_ALRM_MASK))
+ break;
+
+ if (time_after_eq(jiffies, timeout)) {
+ dev_err(dev, "Time out occur, while clearing alarm status bit\n");
+ return -ETIMEDOUT;
+ }
+ writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
+ }
+
writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_EN);
- else
+ } else {
writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
-
+ }
return 0;
}
@@ -183,8 +202,8 @@ static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
if (!(status & (RTC_INT_SEC | RTC_INT_ALRM)))
return IRQ_NONE;
- /* Clear RTC_INT_ALRM interrupt only */
- writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
+ /* Disable RTC_INT_ALRM interrupt only */
+ writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
if (status & RTC_INT_ALRM)
rtc_update_irq(xrtcdev->rtc, 1, RTC_IRQF | RTC_AF);
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable
2019-12-12 13:00 [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable Srinivas Neeli
@ 2020-02-10 11:48 ` Michal Simek
2020-02-11 10:39 ` Alexandre Belloni
0 siblings, 1 reply; 4+ messages in thread
From: Michal Simek @ 2020-02-10 11:48 UTC (permalink / raw)
To: Srinivas Neeli
Cc: Alessandro Zummo, Alexandre Belloni, Srinivas Goud,
Shubhrajyoti Datta, linux-rtc, LKML, linux-arm, git
Hi,
čt 12. 12. 2019 v 14:01 odesílatel Srinivas Neeli
<srinivas.neeli@xilinx.com> napsal:
>
> Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
> clear the alarm interrupt status bit immediately after the interrupt is
> triggered.This is due to the sticky nature of the alarm interrupt status
> register. The alarm interrupt status register can be cleared only after
> the second counter outruns the set alarm value. To fix multiple spurious
> interrupts, disable alarm interrupt in the handler and clear the status
> bit before enabling the alarm interrupt.
>
> Fixes: 11143c19eb57 ("rtc: add xilinx zynqmp rtc driver")
> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> ---
> drivers/rtc/rtc-zynqmp.c | 29 ++++++++++++++++++++++++-----
> 1 file changed, 24 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
> index 5786866c09e9..d311e3ef1f21 100644
> --- a/drivers/rtc/rtc-zynqmp.c
> +++ b/drivers/rtc/rtc-zynqmp.c
> @@ -38,6 +38,8 @@
>
> #define RTC_CALIB_DEF 0x198233
> #define RTC_CALIB_MASK 0x1FFFFF
> +#define RTC_ALRM_MASK BIT(1)
> +#define RTC_MSEC 1000
>
> struct xlnx_rtc_dev {
> struct rtc_device *rtc;
> @@ -124,11 +126,28 @@ static int xlnx_rtc_alarm_irq_enable(struct device *dev, u32 enabled)
> {
> struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
>
here shouldn't be empty line.
> - if (enabled)
> + unsigned int status;
> + ulong timeout;
> +
> + timeout = jiffies + msecs_to_jiffies(RTC_MSEC);
> +
> + if (enabled) {
> + while (1) {
> + status = readl(xrtcdev->reg_base + RTC_INT_STS);
> + if (!((status & RTC_ALRM_MASK) == RTC_ALRM_MASK))
> + break;
> +
> + if (time_after_eq(jiffies, timeout)) {
> + dev_err(dev, "Time out occur, while clearing alarm status bit\n");
> + return -ETIMEDOUT;
> + }
> + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
> + }
> +
> writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_EN);
> - else
> + } else {
> writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
> -
> + }
And here it was good to have empty line.
> return 0;
> }
>
> @@ -183,8 +202,8 @@ static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
> if (!(status & (RTC_INT_SEC | RTC_INT_ALRM)))
> return IRQ_NONE;
>
> - /* Clear RTC_INT_ALRM interrupt only */
> - writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
> + /* Disable RTC_INT_ALRM interrupt only */
> + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
>
> if (status & RTC_INT_ALRM)
> rtc_update_irq(xrtcdev->rtc, 1, RTC_IRQF | RTC_AF);
> --
> 2.7.4
Other then these two above things look good.
Alexandre: Any issue with this patch?
Thanks,
Michal
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable
2020-02-10 11:48 ` Michal Simek
@ 2020-02-11 10:39 ` Alexandre Belloni
2020-02-11 10:40 ` Michal Simek
0 siblings, 1 reply; 4+ messages in thread
From: Alexandre Belloni @ 2020-02-11 10:39 UTC (permalink / raw)
To: Michal Simek
Cc: Srinivas Neeli, Alessandro Zummo, Srinivas Goud,
Shubhrajyoti Datta, linux-rtc, LKML, linux-arm, git
On 10/02/2020 12:48:14+0100, Michal Simek wrote:
> Hi,
>
> čt 12. 12. 2019 v 14:01 odesílatel Srinivas Neeli
> <srinivas.neeli@xilinx.com> napsal:
> >
> > Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
> > clear the alarm interrupt status bit immediately after the interrupt is
> > triggered.This is due to the sticky nature of the alarm interrupt status
> > register. The alarm interrupt status register can be cleared only after
> > the second counter outruns the set alarm value. To fix multiple spurious
> > interrupts, disable alarm interrupt in the handler and clear the status
> > bit before enabling the alarm interrupt.
> >
> > Fixes: 11143c19eb57 ("rtc: add xilinx zynqmp rtc driver")
> > Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
> > ---
> > drivers/rtc/rtc-zynqmp.c | 29 ++++++++++++++++++++++++-----
> > 1 file changed, 24 insertions(+), 5 deletions(-)
> >
> > diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
> > index 5786866c09e9..d311e3ef1f21 100644
> > --- a/drivers/rtc/rtc-zynqmp.c
> > +++ b/drivers/rtc/rtc-zynqmp.c
> > @@ -38,6 +38,8 @@
> >
> > #define RTC_CALIB_DEF 0x198233
> > #define RTC_CALIB_MASK 0x1FFFFF
> > +#define RTC_ALRM_MASK BIT(1)
> > +#define RTC_MSEC 1000
> >
> > struct xlnx_rtc_dev {
> > struct rtc_device *rtc;
> > @@ -124,11 +126,28 @@ static int xlnx_rtc_alarm_irq_enable(struct device *dev, u32 enabled)
> > {
> > struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
> >
>
> here shouldn't be empty line.
>
> > - if (enabled)
> > + unsigned int status;
> > + ulong timeout;
> > +
> > + timeout = jiffies + msecs_to_jiffies(RTC_MSEC);
> > +
> > + if (enabled) {
> > + while (1) {
> > + status = readl(xrtcdev->reg_base + RTC_INT_STS);
> > + if (!((status & RTC_ALRM_MASK) == RTC_ALRM_MASK))
> > + break;
> > +
> > + if (time_after_eq(jiffies, timeout)) {
> > + dev_err(dev, "Time out occur, while clearing alarm status bit\n");
> > + return -ETIMEDOUT;
> > + }
> > + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
> > + }
> > +
> > writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_EN);
> > - else
> > + } else {
> > writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
> > -
> > + }
>
> And here it was good to have empty line.
>
> > return 0;
> > }
> >
> > @@ -183,8 +202,8 @@ static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
> > if (!(status & (RTC_INT_SEC | RTC_INT_ALRM)))
> > return IRQ_NONE;
> >
> > - /* Clear RTC_INT_ALRM interrupt only */
> > - writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
> > + /* Disable RTC_INT_ALRM interrupt only */
> > + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
> >
> > if (status & RTC_INT_ALRM)
> > rtc_update_irq(xrtcdev->rtc, 1, RTC_IRQF | RTC_AF);
> > --
> > 2.7.4
>
> Other then these two above things look good.
>
> Alexandre: Any issue with this patch?
>
No issue, I was kind of waiting for your review. I'll take the patch
once your comments are addressed.
--
Alexandre Belloni, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable
2020-02-11 10:39 ` Alexandre Belloni
@ 2020-02-11 10:40 ` Michal Simek
0 siblings, 0 replies; 4+ messages in thread
From: Michal Simek @ 2020-02-11 10:40 UTC (permalink / raw)
To: Alexandre Belloni, Michal Simek
Cc: Srinivas Neeli, Alessandro Zummo, Srinivas Goud,
Shubhrajyoti Datta, linux-rtc, LKML, linux-arm, git
On 11. 02. 20 11:39, Alexandre Belloni wrote:
> On 10/02/2020 12:48:14+0100, Michal Simek wrote:
>> Hi,
>>
>> čt 12. 12. 2019 v 14:01 odesílatel Srinivas Neeli
>> <srinivas.neeli@xilinx.com> napsal:
>>>
>>> Fix multiple occurring interrupts for alarm interrupt. RTC module doesn't
>>> clear the alarm interrupt status bit immediately after the interrupt is
>>> triggered.This is due to the sticky nature of the alarm interrupt status
>>> register. The alarm interrupt status register can be cleared only after
>>> the second counter outruns the set alarm value. To fix multiple spurious
>>> interrupts, disable alarm interrupt in the handler and clear the status
>>> bit before enabling the alarm interrupt.
>>>
>>> Fixes: 11143c19eb57 ("rtc: add xilinx zynqmp rtc driver")
>>> Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
>>> ---
>>> drivers/rtc/rtc-zynqmp.c | 29 ++++++++++++++++++++++++-----
>>> 1 file changed, 24 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/drivers/rtc/rtc-zynqmp.c b/drivers/rtc/rtc-zynqmp.c
>>> index 5786866c09e9..d311e3ef1f21 100644
>>> --- a/drivers/rtc/rtc-zynqmp.c
>>> +++ b/drivers/rtc/rtc-zynqmp.c
>>> @@ -38,6 +38,8 @@
>>>
>>> #define RTC_CALIB_DEF 0x198233
>>> #define RTC_CALIB_MASK 0x1FFFFF
>>> +#define RTC_ALRM_MASK BIT(1)
>>> +#define RTC_MSEC 1000
>>>
>>> struct xlnx_rtc_dev {
>>> struct rtc_device *rtc;
>>> @@ -124,11 +126,28 @@ static int xlnx_rtc_alarm_irq_enable(struct device *dev, u32 enabled)
>>> {
>>> struct xlnx_rtc_dev *xrtcdev = dev_get_drvdata(dev);
>>>
>>
>> here shouldn't be empty line.
>>
>>> - if (enabled)
>>> + unsigned int status;
>>> + ulong timeout;
>>> +
>>> + timeout = jiffies + msecs_to_jiffies(RTC_MSEC);
>>> +
>>> + if (enabled) {
>>> + while (1) {
>>> + status = readl(xrtcdev->reg_base + RTC_INT_STS);
>>> + if (!((status & RTC_ALRM_MASK) == RTC_ALRM_MASK))
>>> + break;
>>> +
>>> + if (time_after_eq(jiffies, timeout)) {
>>> + dev_err(dev, "Time out occur, while clearing alarm status bit\n");
>>> + return -ETIMEDOUT;
>>> + }
>>> + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
>>> + }
>>> +
>>> writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_EN);
>>> - else
>>> + } else {
>>> writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
>>> -
>>> + }
>>
>> And here it was good to have empty line.
>>
>>> return 0;
>>> }
>>>
>>> @@ -183,8 +202,8 @@ static irqreturn_t xlnx_rtc_interrupt(int irq, void *id)
>>> if (!(status & (RTC_INT_SEC | RTC_INT_ALRM)))
>>> return IRQ_NONE;
>>>
>>> - /* Clear RTC_INT_ALRM interrupt only */
>>> - writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_STS);
>>> + /* Disable RTC_INT_ALRM interrupt only */
>>> + writel(RTC_INT_ALRM, xrtcdev->reg_base + RTC_INT_DIS);
>>>
>>> if (status & RTC_INT_ALRM)
>>> rtc_update_irq(xrtcdev->rtc, 1, RTC_IRQF | RTC_AF);
>>> --
>>> 2.7.4
>>
>> Other then these two above things look good.
>>
>> Alexandre: Any issue with this patch?
>>
>
> No issue, I was kind of waiting for your review. I'll take the patch
> once your comments are addressed.
Ok. Thanks,
Michal
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2020-02-11 10:41 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-12 13:00 [PATCH] rtc: zynqmp: Clear alarm interrupt status before interrupt enable Srinivas Neeli
2020-02-10 11:48 ` Michal Simek
2020-02-11 10:39 ` Alexandre Belloni
2020-02-11 10:40 ` Michal Simek
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).