From: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To: Wei Xu <xuwei5@hisilicon.com>, Rob Herring <robh+dt@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: [PATCH RESEND 4/7] arm64: dts: hisilicon: Add support for Hikey 970 USB3 PHY
Date: Wed, 15 Dec 2021 09:54:30 +0100 [thread overview]
Message-ID: <4ace4c6b2adad26b1f1068aeaf0fcb1e95ba67dc.1639558366.git.mchehab+huawei@kernel.org> (raw)
In-Reply-To: <cover.1639558366.git.mchehab+huawei@kernel.org>
Add the USB3 bindings for Kirin 970 phy and Hikey 970 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
---
To avoid mailbombing on a large number of people, only mailing lists were C/C on the cover.
See [PATCH RESEND 0/7] at: https://lore.kernel.org/all/cover.1639558366.git.mchehab+huawei@kernel.org/
.../boot/dts/hisilicon/hi3670-hikey970.dts | 83 +++++++++++++++++++
arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 56 +++++++++++++
2 files changed, 139 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
index 7c32f5fd5cc5..60594db07041 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts
@@ -430,3 +430,86 @@ &uart6 {
label = "LS-UART1";
status = "okay";
};
+
+&usb_phy {
+ phy-supply = <&ldo17>;
+};
+
+&i2c1 {
+ status = "okay";
+
+ rt1711h: rt1711h@4e {
+ compatible = "richtek,rt1711h";
+ reg = <0x4e>;
+ status = "okay";
+ interrupt-parent = <&gpio27>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_cfg_func>;
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "sink";
+ source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
+ sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
+ PDO_VAR(5000, 5000, 1000)>;
+ op-sink-microwatt = <10000000>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@1 {
+ reg = <1>;
+ usb_con_ss: endpoint {
+ remote-endpoint = <&dwc3_ss>;
+ };
+ };
+ };
+ };
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rt1711h_ep: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&hikey_usb_ep1>;
+ };
+ };
+ };
+};
+
+&i2c2 {
+ /* USB HUB is on this bus at address 0x44 */
+ status = "okay";
+};
+
+&dwc3 { /* USB */
+ dr_mode = "otg";
+ maximum-speed = "super-speed";
+ phy_type = "utmi";
+ snps,dis-del-phy-power-chg-quirk;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,tx_de_emphasis_quirk;
+ snps,tx_de_emphasis = <1>;
+ snps,dis-split-quirk;
+ snps,gctl-reset-quirk;
+ usb-role-switch;
+ role-switch-default-mode = "host";
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dwc3_role_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&hikey_usb_ep0>;
+ };
+
+ dwc3_ss: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&usb_con_ss>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index 636c8817df7e..782e1487666d 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/hi3670-clock.h>
+#include <dt-bindings/usb/pd.h>
/ {
compatible = "hisilicon,hi3670";
@@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 {
pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>;
status = "disabled";
};
+
+ usb3_otg_bc: usb3_otg_bc@ff200000 {
+ compatible = "syscon", "simple-mfd";
+ reg = <0x0 0xff200000 0x0 0x1000>;
+
+ usb_phy: usbphy {
+ compatible = "hisilicon,hi3670-usb-phy";
+ #phy-cells = <0>;
+ hisilicon,pericrg-syscon = <&crg_ctrl>;
+ hisilicon,pctrl-syscon = <&pctrl>;
+ hisilicon,sctrl-syscon = <&sctrl>;
+ hisilicon,eye-diagram-param = <0xFDFEE4>;
+ hisilicon,tx-vboost-lvl = <0x5>;
+ };
+ };
+
+ usb31_misc_rst: usb31_misc_rst_controller {
+ compatible = "hisilicon,hi3660-reset";
+ #reset-cells = <2>;
+ hisi,rst-syscon = <&usb3_otg_bc>;
+ };
+
+ usb3: hisi_dwc3 {
+ compatible = "hisilicon,hi3670-dwc3";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>,
+ <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>,
+ <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>,
+ <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+ clock-names = "clk_gate_abb_usb",
+ "hclk_gate_usb3otg",
+ "clk_gate_usb3otg_ref",
+ "aclk_gate_usb3dvfs";
+
+ assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>;
+ assigned-clock-rates = <238000000>;
+ resets = <&crg_rst 0x90 6>,
+ <&crg_rst 0x90 7>,
+ <&usb31_misc_rst 0xA0 8>,
+ <&usb31_misc_rst 0xA0 9>;
+
+ dwc3: usb@ff100000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff100000 0x0 0x100000>;
+
+ interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>,
+ <0 161 IRQ_TYPE_LEVEL_HIGH>;
+
+ phys = <&usb_phy>;
+ phy-names = "usb3-phy";
+ };
+ };
};
};
--
2.33.1
next prev parent reply other threads:[~2021-12-15 8:54 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-15 8:54 [PATCH RESEND 0/7] DT bindings for Hikey960/970 USB/PCI Mauro Carvalho Chehab
2021-12-15 8:54 ` [PATCH RESEND 1/7] dt-bindings: misc: add schema for USB hub on Kirin devices Mauro Carvalho Chehab
2021-12-16 19:52 ` Rob Herring
2021-12-17 9:32 ` Mauro Carvalho Chehab
2021-12-15 8:54 ` [PATCH RESEND 2/7] dt-bindings: clock: hi3670-clock.txt: add pmctrl compatible Mauro Carvalho Chehab
2021-12-16 19:54 ` Rob Herring
2021-12-15 8:54 ` [PATCH RESEND 3/7] dt-bindings: usb: hisilicon,hi3670-dwc3: add binding for Kirin970 Mauro Carvalho Chehab
2021-12-16 20:01 ` Rob Herring
2021-12-15 8:54 ` Mauro Carvalho Chehab [this message]
2021-12-15 8:54 ` [PATCH RESEND 5/7] arm64: dts: HiSilicon: Add support for HiKey 970 PCIe controller hardware Mauro Carvalho Chehab
2021-12-15 8:54 ` [PATCH RESEND 6/7] arm64: dts: hisilicon: Add usb mux hub for hikey970 Mauro Carvalho Chehab
2021-12-15 8:54 ` [PATCH RESEND 7/7] arm64: dts: hisilicon: Add usb mux hub for hikey960 Mauro Carvalho Chehab
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4ace4c6b2adad26b1f1068aeaf0fcb1e95ba67dc.1639558366.git.mchehab+huawei@kernel.org \
--to=mchehab+huawei@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).