Re: [PATCH v4 1/2] dt-bindings: phy: ti: phy-gmii-sel: Add bindings for J7200

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 01/09/2022 11:55, Siddharth Vadapalli wrote:
> TI's J7200 SoC supports additional PHY modes like QSGMII and SGMII
> that are not supported on earlier SoCs. Add a compatible for it.
> 
> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
> ---
>  .../mfd/ti,j721e-system-controller.yaml       |  6 ++++
>  .../bindings/phy/ti,phy-gmii-sel.yaml         | 30 ++++++++++++++++++-
>  2 files changed, 35 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
> index 1aeac43cad92..802374e7645f 100644
> --- a/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
> +++ b/Documentation/devicetree/bindings/mfd/ti,j721e-system-controller.yaml
> @@ -54,6 +54,12 @@ patternProperties:
>      description:
>        Clock provider for TI EHRPWM nodes.
>  
> +  "phy@[0-9a-f]+$":
> +    type: object
> +    $ref: /schemas/phy/phy-provider.yaml

You need instead ref to specific device bindings/schema. Probably to
/schemas/phy/ti,phy-gmii-sel.yaml#

This was entirely different in v3, so your change is very confusing.

> +    description:
> +      This is the register to set phy mode through phy-gmii-sel driver.

I don't understand the description. Please focus on the hardware not
some drivers - what is here? Phy for something?

> +
>  required:
>    - compatible
>    - reg
> diff --git a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> index ff8a6d9eb153..0ffb97f1a77c 100644
> --- a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> +++ b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml
> @@ -53,12 +53,24 @@ properties:
>        - ti,am43xx-phy-gmii-sel
>        - ti,dm814-phy-gmii-sel
>        - ti,am654-phy-gmii-sel
> +      - ti,j7200-cpsw5g-phy-gmii-sel
>  
>    reg:
>      maxItems: 1
>  
>    '#phy-cells': true
>  
> +  ti,qsgmii-main-ports:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    description: |
> +      Required only for QSGMII mode. Array to select the port for
> +      QSGMII main mode. Rest of the ports are selected as QSGMII_SUB
> +      ports automatically. Any one of the 4 CPSW5G ports can act as the
> +      main port with the rest of them being the QSGMII_SUB ports.
> +    items:
> +      minimum: 1
> +      maximum: 4
> +
>  allOf:
>    - if:
>        properties:
> @@ -73,6 +85,22 @@ allOf:
>          '#phy-cells':
>            const: 1
>            description: CPSW port number (starting from 1)

Blank line


> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - ti,j7200-cpsw5g-phy-gmii-sel
> +    then:
> +      properties:
> +        '#phy-cells':
> +          const: 1
> +          description: CPSW port number (starting from 1)
> +        ti,qsgmii-main-ports:
> +          maxItems: 1

It does not really make sense to limit items here, in the context of
this patch. You got a comment for it already. Your patch should make
sense on its own.

> +    else:
> +      properties:
> +        ti,qsgmii-main-ports: false

Blank line

>    - if:
>        properties:
>          compatible:
> @@ -97,7 +125,7 @@ additionalProperties: false
>  
>  examples:
>    - |
> -    phy_gmii_sel: phy-gmii-sel@650 {
> +    phy_gmii_sel: phy@650 {

Split cleanup into separate patch.

>          compatible = "ti,am3352-phy-gmii-sel";
>          reg = <0x650 0x4>;
>          #phy-cells = <2>;


Best regards,
Krzysztof