linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ola Lilja <ola.o.lilja@stericsson.com>
To: Lee Jones <lee.jones@linaro.org>
Cc: "linux-arm-kernel@lists.infradead.org" 
	<linux-arm-kernel@lists.infradead.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	STEricsson_nomadik_linux <STEricsson_nomadik_linux@list.st.com>,
	Linus WALLEIJ <linus.walleij@stericsson.com>,
	"arnd@arndb.de" <arnd@arndb.de>,
	"broonie@opensource.wolfsonmicro.com" 
	<broonie@opensource.wolfsonmicro.com>,
	Roger NILSSON1 <roger.xr.nilsson@stericsson.com>,
	"alsa-devel@alsa-project.org" <alsa-devel@alsa-project.org>
Subject: Re: [PATCH 01/17] ASoC: Ux500: Move MSP pinctrl setup into the MSP driver
Date: Tue, 11 Sep 2012 11:28:16 +0200	[thread overview]
Message-ID: <504F0430.8070009@stericsson.com> (raw)
In-Reply-To: <20120910164628.GG24506@gmail.com>

On 09/10/2012 06:46 PM, Lee Jones wrote:

> Ola poke.
> 
> On Fri, Aug 24, 2012 at 03:01:37PM +0100, Lee Jones wrote:
>> In the initial submission of the MSP driver msp1 and msp3's associated
>> pinctrl mechanism was passed back to platform code using a plat_init()
>> call-back routine, but it has no place in platform code. The MSP driver
>> should set this up for the appropriate ports. Instead we use a use_pinctrl
>> identifier which is passed from platform_data/Device Tree which indicates
>> which ports should use pinctrl.
>> 
>> CC: alsa-devel@alsa-project.org
>> Signed-off-by: Lee Jones <lee.jones@linaro.org>
>> ---
>>  arch/arm/mach-ux500/board-mop500-msp.c |   75 +-------------------------------
>>  arch/arm/mach-ux500/include/mach/msp.h |    2 -
>>  sound/soc/ux500/ux500_msp_i2s.c        |   67 +++++++++++++++++++++-------
>>  sound/soc/ux500/ux500_msp_i2s.h        |    8 +++-
>>  4 files changed, 58 insertions(+), 94 deletions(-)
>> 
>> diff --git a/arch/arm/mach-ux500/board-mop500-msp.c b/arch/arm/mach-ux500/board-mop500-msp.c
>> index df15646..fc78d5d 100644
>> --- a/arch/arm/mach-ux500/board-mop500-msp.c
>> +++ b/arch/arm/mach-ux500/board-mop500-msp.c
>> @@ -23,53 +23,6 @@
>>  #include "devices-db8500.h"
>>  #include "pins-db8500.h"
>>  
>> -/* MSP1/3 Tx/Rx usage protection */
>> -static DEFINE_SPINLOCK(msp_rxtx_lock);
>> -
>> -/* Reference Count */
>> -static int msp_rxtx_ref;
>> -
>> -/* Pin modes */
>> -struct pinctrl *msp1_p;
>> -struct pinctrl_state *msp1_def;
>> -struct pinctrl_state *msp1_sleep;
>> -
>> -int msp13_i2s_init(void)
>> -{
>> -	int retval = 0;
>> -	unsigned long flags;
>> -
>> -	spin_lock_irqsave(&msp_rxtx_lock, flags);
>> -	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_def))) {
>> -		retval = pinctrl_select_state(msp1_p, msp1_def);
>> -		if (retval)
>> -			pr_err("could not set MSP1 defstate\n");
>> -	}
>> -	if (!retval)
>> -		msp_rxtx_ref++;
>> -	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> -
>> -	return retval;
>> -}
>> -
>> -int msp13_i2s_exit(void)
>> -{
>> -	int retval = 0;
>> -	unsigned long flags;
>> -
>> -	spin_lock_irqsave(&msp_rxtx_lock, flags);
>> -	WARN_ON(!msp_rxtx_ref);
>> -	msp_rxtx_ref--;
>> -	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_sleep))) {
>> -		retval = pinctrl_select_state(msp1_p, msp1_sleep);
>> -		if (retval)
>> -			pr_err("could not set MSP1 sleepstate\n");
>> -	}
>> -	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> -
>> -	return retval;
>> -}
>> -
>>  static struct stedma40_chan_cfg msp0_dma_rx = {
>>  	.high_priority = true,
>>  	.dir = STEDMA40_PERIPH_TO_MEM,
>> @@ -132,8 +85,6 @@ static struct msp_i2s_platform_data msp1_platform_data = {
>>  	.id = MSP_I2S_1,
>>  	.msp_i2s_dma_rx = NULL,
>>  	.msp_i2s_dma_tx = &msp1_dma_tx,
>> -	.msp_i2s_init = msp13_i2s_init,
>> -	.msp_i2s_exit = msp13_i2s_exit,
>>  };
>>  
>>  static struct stedma40_chan_cfg msp2_dma_rx = {
>> @@ -219,47 +170,23 @@ static struct msp_i2s_platform_data msp3_platform_data = {
>>  	.id		= MSP_I2S_3,
>>  	.msp_i2s_dma_rx	= &msp1_dma_rx,
>>  	.msp_i2s_dma_tx	= NULL,
>> -	.msp_i2s_init = msp13_i2s_init,
>> -	.msp_i2s_exit = msp13_i2s_exit,
>>  };
>>  
>>  int mop500_msp_init(struct device *parent)
>>  {
>> -	struct platform_device *msp1;
>> -
>>  	pr_info("%s: Register platform-device 'snd-soc-mop500'.\n", __func__);
>>  	platform_device_register(&snd_soc_mop500);
>>  
>>  	pr_info("Initialize MSP I2S-devices.\n");
>>  	db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
>>  			   &msp0_platform_data);
>> -	msp1 = db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
>> +	db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
>>  			   &msp1_platform_data);
>>  	db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
>>  			   &msp2_platform_data);
>>  	db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
>>  			   &msp3_platform_data);
>>  
>> -	/* Get the pinctrl handle for MSP1 */
>> -	if (msp1) {
>> -		msp1_p = pinctrl_get(&msp1->dev);
>> -		if (IS_ERR(msp1_p))
>> -			dev_err(&msp1->dev, "could not get MSP1 pinctrl\n");
>> -		else {
>> -			msp1_def = pinctrl_lookup_state(msp1_p,
>> -							PINCTRL_STATE_DEFAULT);
>> -			if (IS_ERR(msp1_def)) {
>> -				dev_err(&msp1->dev,
>> -					"could not get MSP1 defstate\n");
>> -			}
>> -			msp1_sleep = pinctrl_lookup_state(msp1_p,
>> -							  PINCTRL_STATE_SLEEP);
>> -			if (IS_ERR(msp1_sleep))
>> -				dev_err(&msp1->dev,
>> -					"could not get MSP1 idlestate\n");
>> -		}
>> -	}
>> -
>>  	pr_info("%s: Register platform-device 'ux500-pcm'\n", __func__);
>>  	platform_device_register(&ux500_pcm);
>>  
>> diff --git a/arch/arm/mach-ux500/include/mach/msp.h b/arch/arm/mach-ux500/include/mach/msp.h
>> index 798be19..3cc7142 100644
>> --- a/arch/arm/mach-ux500/include/mach/msp.h
>> +++ b/arch/arm/mach-ux500/include/mach/msp.h
>> @@ -22,8 +22,6 @@ struct msp_i2s_platform_data {
>>  	enum msp_i2s_id id;
>>  	struct stedma40_chan_cfg *msp_i2s_dma_rx;
>>  	struct stedma40_chan_cfg *msp_i2s_dma_tx;
>> -	int (*msp_i2s_init) (void);
>> -	int (*msp_i2s_exit) (void);
>>  };
>>  
>>  #endif
>> diff --git a/sound/soc/ux500/ux500_msp_i2s.c b/sound/soc/ux500/ux500_msp_i2s.c
>> index 36be11e..08813c5 100644
>> --- a/sound/soc/ux500/ux500_msp_i2s.c
>> +++ b/sound/soc/ux500/ux500_msp_i2s.c
>> @@ -15,6 +15,7 @@
>>  
>>  #include <linux/module.h>
>>  #include <linux/platform_device.h>
>> +#include <linux/pinctrl/consumer.h>
>>  #include <linux/delay.h>
>>  #include <linux/slab.h>
>>  
>> @@ -25,6 +26,9 @@
>>  
>>  #include "ux500_msp_i2s.h"
>>  
>> +/* MSP1/3 Tx/Rx usage protection */
>> +static DEFINE_SPINLOCK(msp_rxtx_lock);
>> +
>>   /* Protocol desciptors */
>>  static const struct msp_protdesc prot_descs[] = {
>>  	{ /* I2S */
>> @@ -352,17 +356,23 @@ static int configure_multichannel(struct ux500_msp *msp,
>>  
>>  static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config)
>>  {
>> -	int status = 0;
>> +	int status = 0, retval = 0;
>>  	u32 reg_val_DMACR, reg_val_GCR;
>> +	unsigned long flags;
>>  
>>  	/* Check msp state whether in RUN or CONFIGURED Mode */
>> -	if ((msp->msp_state == MSP_STATE_IDLE) && (msp->plat_init)) {
>> -		status = msp->plat_init();
>> -		if (status) {
>> -			dev_err(msp->dev, "%s: ERROR: Failed to init MSP (%d)!\n",
>> -				__func__, status);
>> -			return status;
>> +	if (msp->msp_state == MSP_STATE_IDLE) {
>> +		spin_lock_irqsave(&msp_rxtx_lock, flags);
>> +		if (msp->pinctrl_rxtx_ref == 0 &&
>> +			!(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_def))) {
>> +			retval = pinctrl_select_state(msp->pinctrl_p,
>> +						msp->pinctrl_def);
>> +			if (retval)
>> +				pr_err("could not set MSP defstate\n");
>>  		}
>> +		if (!retval)
>> +			msp->pinctrl_rxtx_ref++;
>> +		spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>>  	}
>>  
>>  	/* Configure msp with protocol dependent settings */
>> @@ -620,7 +630,8 @@ int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction)
>>  
>>  int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
>>  {
>> -	int status = 0;
>> +	int status = 0, retval = 0;
>> +	unsigned long flags;
>>  
>>  	dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir);
>>  
>> @@ -631,12 +642,19 @@ int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir)
>>  		writel((readl(msp->registers + MSP_GCR) &
>>  			       (~(FRAME_GEN_ENABLE | SRG_ENABLE))),
>>  			      msp->registers + MSP_GCR);
>> -		if (msp->plat_exit)
>> -			status = msp->plat_exit();
>> -			if (status)
>> -				dev_warn(msp->dev,
>> -					"%s: WARN: ux500_msp_i2s_exit failed (%d)!\n",
>> -					__func__, status);
>> +
>> +		spin_lock_irqsave(&msp_rxtx_lock, flags);
>> +		WARN_ON(!msp->pinctrl_rxtx_ref);
>> +		msp->pinctrl_rxtx_ref--;
>> +		if (msp->pinctrl_rxtx_ref == 0 &&
>> +			!(IS_ERR(msp->pinctrl_p) || IS_ERR(msp->pinctrl_sleep))) {
>> +			retval = pinctrl_select_state(msp->pinctrl_p,
>> +						msp->pinctrl_sleep);
>> +			if (retval)
>> +				pr_err("could not set MSP sleepstate\n");
>> +		}
>> +		spin_unlock_irqrestore(&msp_rxtx_lock, flags);
>> +
>>  		writel(0, msp->registers + MSP_GCR);
>>  		writel(0, msp->registers + MSP_TCF);
>>  		writel(0, msp->registers + MSP_RCF);
>> @@ -678,8 +696,6 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
>>  
>>  	msp->id = platform_data->id;
>>  	msp->dev = &pdev->dev;
>> -	msp->plat_init = platform_data->msp_i2s_init;
>> -	msp->plat_exit = platform_data->msp_i2s_exit;
>>  	msp->dma_cfg_rx = platform_data->msp_i2s_dma_rx;
>>  	msp->dma_cfg_tx = platform_data->msp_i2s_dma_tx;
>>  
>> @@ -717,6 +733,25 @@ int ux500_msp_i2s_init_msp(struct platform_device *pdev,
>>  	dev_dbg(&pdev->dev, "I2S device-name: '%s'\n", i2s_cont->name);
>>  	msp->i2s_cont = i2s_cont;
>>  
>> +	msp->pinctrl_p = pinctrl_get(msp->dev);
>> +	if (IS_ERR(msp->pinctrl_p))
>> +		dev_err(&pdev->dev, "could not get MSP pinctrl\n");
>> +	else {
>> +		msp->pinctrl_def = pinctrl_lookup_state(msp->pinctrl_p,
>> +						PINCTRL_STATE_DEFAULT);
>> +		if (IS_ERR(msp->pinctrl_def)) {
>> +			dev_err(&pdev->dev,
>> +				"could not get MSP defstate (%li)\n",
>> +				PTR_ERR(msp->pinctrl_def));
>> +		}
>> +		msp->pinctrl_sleep = pinctrl_lookup_state(msp->pinctrl_p,
>> +						PINCTRL_STATE_SLEEP);
>> +		if (IS_ERR(msp->pinctrl_sleep))
>> +			dev_err(&pdev->dev,
>> +				"could not get MSP idlestate (%li)\n",
>> +				PTR_ERR(msp->pinctrl_def));
>> +	}
>> +
>>  	return 0;
>>  
>>  err_i2s_cont:
>> diff --git a/sound/soc/ux500/ux500_msp_i2s.h b/sound/soc/ux500/ux500_msp_i2s.h
>> index 2d9136d..1311c0d 100644
>> --- a/sound/soc/ux500/ux500_msp_i2s.h
>> +++ b/sound/soc/ux500/ux500_msp_i2s.h
>> @@ -524,14 +524,18 @@ struct ux500_msp {
>>  	struct dma_chan *rx_pipeid;
>>  	enum msp_state msp_state;
>>  	int (*transfer) (struct ux500_msp *msp, struct i2s_message *message);
>> -	int (*plat_init) (void);
>> -	int (*plat_exit) (void);
>>  	struct timer_list notify_timer;
>>  	int def_elem_len;
>>  	unsigned int dir_busy;
>>  	int loopback_enable;
>>  	u32 backup_regs[MAX_MSP_BACKUP_REGS];
>>  	unsigned int f_bitclk;
>> +	/* Pin modes */
>> +	struct pinctrl *pinctrl_p;
>> +	struct pinctrl_state *pinctrl_def;
>> +	struct pinctrl_state *pinctrl_sleep;
>> +	/* Reference Count */
>> +	int pinctrl_rxtx_ref;
>>  };
>>  
>>  struct ux500_msp_dma_params {
>> -- 
>> 1.7.9.5
>> 
> 


Looks OK from my perspective!

  reply	other threads:[~2012-09-11  9:28 UTC|newest]

Thread overview: 36+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2012-08-24 14:01 [PATCH 00/17] MOP500 Audio fix-ups and DT enablement Lee Jones
2012-08-24 14:01 ` [PATCH 01/17] ASoC: Ux500: Move MSP pinctrl setup into the MSP driver Lee Jones
2012-08-30 23:46   ` Linus Walleij
2012-09-10 16:46   ` Lee Jones
2012-09-11  9:28     ` Ola Lilja [this message]
2012-08-24 14:01 ` [PATCH 02/17] ASoC: Ux500: Enable MOP500 driver for Device Tree Lee Jones
2012-08-24 14:01 ` [PATCH 03/17] ASoC: Ux500: Enable ux500 MSP " Lee Jones
2012-08-24 14:01 ` [PATCH 04/17] ASoC: codecs: Enable AB8500 CODEC " Lee Jones
2012-08-24 14:01 ` [PATCH 05/17] ASoC: Ux500: Minor coding layout changes Lee Jones
2012-09-10 16:44   ` Lee Jones
2012-09-11  0:27     ` Mark Brown
2012-09-11  9:03     ` Ola Lilja
2012-08-24 14:01 ` [PATCH 06/17] Documentation: Define the MOP500 Audio Machine Driver Device Tree bindings Lee Jones
2012-09-10 16:44   ` Lee Jones
2012-09-11  9:06     ` Ola Lilja
2012-09-11  9:08       ` Mark Brown
2012-09-14 10:02       ` Lee Jones
2012-08-24 14:01 ` [PATCH 07/17] Documentation: Define the MSP " Lee Jones
2012-09-10 16:43   ` Lee Jones
2012-09-11  9:08     ` Ola Lilja
2012-09-14  9:57       ` Lee Jones
2012-08-24 14:01 ` [PATCH 08/17] ARM: ux500: Clean-up MSP platform code Lee Jones
2012-08-24 14:01 ` [PATCH 09/17] ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree Lee Jones
2012-08-30 23:50   ` Linus Walleij
2012-08-24 14:01 ` [PATCH 10/17] ARM: ux500: Fork MSP platform registration for step-by-step DT enablement Lee Jones
2012-08-24 14:01 ` [PATCH 11/17] ARM: ux500: Pass MSP DMA platform data though AUXDATA Lee Jones
2012-08-24 14:01 ` [PATCH 12/17] ARM: ux500: Stop registering the MOP500 Audio driver from platform code Lee Jones
2012-08-24 14:01 ` [PATCH 13/17] ARM: ux500: Remove platform registration of MSP devices Lee Jones
2012-08-24 14:01 ` [PATCH 14/17] ARM: ux500: Rename MSP board file to something more meaningful Lee Jones
2012-08-24 15:05   ` [alsa-devel] " Hebbar, Gururaja
2012-08-24 15:08     ` Lee Jones
2012-08-24 15:14     ` Lee Jones
2012-08-24 15:16       ` Hebbar, Gururaja
2012-08-24 14:01 ` [PATCH 15/17] ARM: ux500: Add nodes for the MSP into Device Tree Lee Jones
2012-08-24 14:01 ` [PATCH 16/17] ARM: ux500: Add all encompassing sound node to the Snowball " Lee Jones
2012-08-24 14:01 ` [PATCH 17/17] Documentation: Add the AB8500 CODEC device to the MFD AB8500 doc Lee Jones

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=504F0430.8070009@stericsson.com \
    --to=ola.o.lilja@stericsson.com \
    --cc=STEricsson_nomadik_linux@list.st.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=arnd@arndb.de \
    --cc=broonie@opensource.wolfsonmicro.com \
    --cc=lee.jones@linaro.org \
    --cc=linus.walleij@stericsson.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=roger.xr.nilsson@stericsson.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).