On 25-06-2013 07:46, Amit Daniel Kachhap wrote: > This patch adds support for h/w mode calibration in the TMU controller. > Soc's like 5440 support this features. The h/w supports two point calibration > and one point calibration at 85C and 25C. > > Acked-by: Jonghwa Lee > Acked-by: Kukjin Kim > Signed-off-by: Amit Daniel Kachhap Acked-by: Eduardo Valentin > --- > Changes in this patch fixes a setting up of wrong calibration mode by defining > trim type for 25 and 85C. This will be only used in H/W based calibration. > > drivers/thermal/samsung/exynos_tmu.c | 33 ++++++++++++++++++++++++++++- > drivers/thermal/samsung/exynos_tmu.h | 8 +++++++ > drivers/thermal/samsung/exynos_tmu_data.c | 2 + > drivers/thermal/samsung/exynos_tmu_data.h | 2 + > 4 files changed, 44 insertions(+), 1 deletions(-) > > diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c > index 3fac0f9..a6fc379 100644 > --- a/drivers/thermal/samsung/exynos_tmu.c > +++ b/drivers/thermal/samsung/exynos_tmu.c > @@ -73,6 +73,9 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp) > struct exynos_tmu_platform_data *pdata = data->pdata; > int temp_code; > > + if (pdata->cal_mode == HW_MODE) > + return temp; > + > if (data->soc == SOC_ARCH_EXYNOS4210) > /* temp should range between 25 and 125 */ > if (temp < 25 || temp > 125) { > @@ -107,6 +110,9 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) > struct exynos_tmu_platform_data *pdata = data->pdata; > int temp; > > + if (pdata->cal_mode == HW_MODE) > + return temp_code; > + > if (data->soc == SOC_ARCH_EXYNOS4210) > /* temp_code should range between 75 and 175 */ > if (temp_code < 75 || temp_code > 175) { > @@ -155,6 +161,9 @@ static int exynos_tmu_initialize(struct platform_device *pdev) > if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) > __raw_writel(1, data->base + reg->triminfo_ctrl); > > + if (pdata->cal_mode == HW_MODE) > + goto skip_calib_data; > + > /* Save trimming info in order to perform calibration */ > if (data->soc == SOC_ARCH_EXYNOS5440) { > /* > @@ -190,6 +199,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) > (pdata->efuse_value >> reg->triminfo_85_shift) & > EXYNOS_TMU_TEMP_MASK; > > +skip_calib_data: > if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) { > dev_err(&pdev->dev, "Invalid max trigger level\n"); > goto out; > @@ -297,7 +307,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) > struct exynos_tmu_data *data = platform_get_drvdata(pdev); > struct exynos_tmu_platform_data *pdata = data->pdata; > const struct exynos_tmu_registers *reg = pdata->registers; > - unsigned int con, interrupt_en; > + unsigned int con, interrupt_en, cal_val; > > mutex_lock(&data->lock); > clk_enable(data->clk); > @@ -320,6 +330,27 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) > con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift); > } > > + if (pdata->cal_mode == HW_MODE) { > + con &= ~(reg->calib_mode_mask << reg->calib_mode_shift); > + cal_val = 0; > + switch (pdata->cal_type) { > + case TYPE_TWO_POINT_TRIMMING: > + cal_val = 3; > + break; > + case TYPE_ONE_POINT_TRIMMING_85: > + cal_val = 2; > + break; > + case TYPE_ONE_POINT_TRIMMING_25: > + cal_val = 1; > + break; > + case TYPE_NONE: > + break; > + default: > + dev_err(&pdev->dev, "Invalid calibration type, using none\n"); > + } > + con |= cal_val << reg->calib_mode_shift; > + } > + > if (on) { > con |= (1 << reg->core_en_shift); > interrupt_en = > diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h > index 25c48d4..b364c9e 100644 > --- a/drivers/thermal/samsung/exynos_tmu.h > +++ b/drivers/thermal/samsung/exynos_tmu.h > @@ -28,6 +28,8 @@ > > enum calibration_type { > TYPE_ONE_POINT_TRIMMING, > + TYPE_ONE_POINT_TRIMMING_25, > + TYPE_ONE_POINT_TRIMMING_85, > TYPE_TWO_POINT_TRIMMING, > TYPE_NONE, > }; > @@ -90,6 +92,10 @@ enum soc_type { > * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl > register. > * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register. > + * @calib_mode_shift: shift bits of calibration mode value in tmu_ctrl > + register. > + * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl > + register. > * @therm_trip_tq_en_shift: shift bits of thermal trip enable by TQ pin in > tmu_ctrl register. > * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register. > @@ -151,6 +157,8 @@ struct exynos_tmu_registers { > u32 therm_trip_en_shift; > u32 buf_slope_sel_shift; > u32 buf_slope_sel_mask; > + u32 calib_mode_shift; > + u32 calib_mode_mask; > u32 therm_trip_tq_en_shift; > u32 core_en_shift; > > diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c > index 5952915..9002499 100644 > --- a/drivers/thermal/samsung/exynos_tmu_data.c > +++ b/drivers/thermal/samsung/exynos_tmu_data.c > @@ -189,6 +189,8 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { > .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, > .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, > .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, > + .calib_mode_shift = EXYNOS_TMU_CALIB_MODE_SHIFT, > + .calib_mode_mask = EXYNOS_TMU_CALIB_MODE_MASK, > .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, > .tmu_status = EXYNOS5440_TMU_S0_7_STATUS, > .tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP, > diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h > index 43ce5fb..dc7feb5 100644 > --- a/drivers/thermal/samsung/exynos_tmu_data.h > +++ b/drivers/thermal/samsung/exynos_tmu_data.h > @@ -75,6 +75,8 @@ > #define EXYNOS_TMU_TRIP_MODE_SHIFT 13 > #define EXYNOS_TMU_TRIP_MODE_MASK 0x7 > #define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12 > +#define EXYNOS_TMU_CALIB_MODE_SHIFT 4 > +#define EXYNOS_TMU_CALIB_MODE_MASK 0x3 > > #define EXYNOS_TMU_INTEN_RISE0_SHIFT 0 > #define EXYNOS_TMU_INTEN_RISE1_SHIFT 4 > -- You have got to be excited about what you are doing. (L. Lamport) Eduardo Valentin