From: Stefan Agner <stefan@agner.ch>
To: Boris Brezillon <boris.brezillon@bootlin.com>, axboe@kernel.dk
Cc: Dmitry Osipenko <digetx@gmail.com>,
dwmw2@infradead.org, computersforpeace@gmail.com,
marek.vasut@gmail.com, robh+dt@kernel.org, mark.rutland@arm.com,
thierry.reding@gmail.com, dev@lynxeye.de,
miquel.raynal@bootlin.com, richard@nod.at, marcel@ziswiler.com,
krzk@kernel.org, benjamin.lindqvist@endian.se,
jonathanh@nvidia.com, pdeschrijver@nvidia.com,
pgaikwad@nvidia.com, mirza.krak@gmail.com, gaireg@gaireg.de,
linux-mtd@lists.infradead.org, linux-tegra@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver
Date: Tue, 12 Jun 2018 11:17:09 +0200 [thread overview]
Message-ID: <53e36cff80e38e489959aa18471d0782@agner.ch> (raw)
In-Reply-To: <20180612102734.0ea3bfa5@bbrezillon>
[also added Jens Axboe]
On 12.06.2018 10:27, Boris Brezillon wrote:
> On Tue, 12 Jun 2018 10:06:42 +0200
> Stefan Agner <stefan@agner.ch> wrote:
>
>> On 12.06.2018 02:03, Dmitry Osipenko wrote:
>> > On Monday, 11 June 2018 23:52:22 MSK Stefan Agner wrote:
>> >> Add support for the NAND flash controller found on NVIDIA
>> >> Tegra 2 SoCs. This implementation does not make use of the
>> >> command queue feature. Regular operations/data transfers are
>> >> done in PIO mode. Page read/writes with hardware ECC make
>> >> use of the DMA for data transfer.
>> >>
>> >> Signed-off-by: Lucas Stach <dev@lynxeye.de>
>> >> Signed-off-by: Stefan Agner <stefan@agner.ch>
>> >> ---
>> >> MAINTAINERS | 7 +
>> >> drivers/mtd/nand/raw/Kconfig | 6 +
>> >> drivers/mtd/nand/raw/Makefile | 1 +
>> >> drivers/mtd/nand/raw/tegra_nand.c | 1248 +++++++++++++++++++++++++++++
>> >> 4 files changed, 1262 insertions(+)
>> >> create mode 100644 drivers/mtd/nand/raw/tegra_nand.c
>> >>
>> [snip]
>> >> +static int tegra_nand_cmd(struct nand_chip *chip,
>> >> + const struct nand_subop *subop)
>> >> +{
>> >> + const struct nand_op_instr *instr;
>> >> + const struct nand_op_instr *instr_data_in = NULL;
>> >> + struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
>> >> + unsigned int op_id, size = 0, offset = 0;
>> >> + bool first_cmd = true;
>> >> + u32 reg, cmd = 0;
>> >> + int ret;
>> >> +
>> >> + for (op_id = 0; op_id < subop->ninstrs; op_id++) {
>> >> + unsigned int naddrs, i;
>> >> + const u8 *addrs;
>> >> + u32 addr1 = 0, addr2 = 0;
>> >> +
>> >> + instr = &subop->instrs[op_id];
>> >> +
>> >> + switch (instr->type) {
>> >> + case NAND_OP_CMD_INSTR:
>> >> + if (first_cmd) {
>> >> + cmd |= COMMAND_CLE;
>> >> + writel_relaxed(instr->ctx.cmd.opcode,
>> >> + ctrl->regs + CMD_REG1);
>> >> + } else {
>> >> + cmd |= COMMAND_SEC_CMD;
>> >> + writel_relaxed(instr->ctx.cmd.opcode,
>> >> + ctrl->regs + CMD_REG2);
>> >> + }
>> >> + first_cmd = false;
>> >> + break;
>> >> + case NAND_OP_ADDR_INSTR:
>> >> + offset = nand_subop_get_addr_start_off(subop, op_id);
>> >> + naddrs = nand_subop_get_num_addr_cyc(subop, op_id);
>> >> + addrs = &instr->ctx.addr.addrs[offset];
>> >> +
>> >> + cmd |= COMMAND_ALE | COMMAND_ALE_SIZE(naddrs);
>> >> + for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> >> + addr1 |= *addrs++ << (BITS_PER_BYTE * i);
>> >> + naddrs -= i;
>> >> + for (i = 0; i < min_t(unsigned int, 4, naddrs); i++)
>> >> + addr2 |= *addrs++ << (BITS_PER_BYTE * i);
>> >> + writel_relaxed(addr1, ctrl->regs + ADDR_REG1);
>> >> + writel_relaxed(addr2, ctrl->regs + ADDR_REG2);
>> >> + break;
>> >> +
>> >> + case NAND_OP_DATA_IN_INSTR:
>> >> + size = nand_subop_get_data_len(subop, op_id);
>> >> + offset = nand_subop_get_data_start_off(subop, op_id);
>> >> +
>> >> + cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> >> + COMMAND_RX | COMMAND_A_VALID;
>> >> +
>> >> + instr_data_in = instr;
>> >> + break;
>> >> +
>> >> + case NAND_OP_DATA_OUT_INSTR:
>> >> + size = nand_subop_get_data_len(subop, op_id);
>> >> + offset = nand_subop_get_data_start_off(subop, op_id);
>> >> +
>> >> + cmd |= COMMAND_TRANS_SIZE(size) | COMMAND_PIO |
>> >> + COMMAND_TX | COMMAND_A_VALID;
>> >> +
>> >> + memcpy(®, instr->ctx.data.buf.out + offset, size);
>> >> + writel_relaxed(reg, ctrl->regs + RESP);
>> >> +
>> >> + break;
>> >> + case NAND_OP_WAITRDY_INSTR:
>> >> + cmd |= COMMAND_RBSY_CHK;
>> >> + break;
>> >> +
>> >> + }
>> >> + }
>> >> +
>> >> + cmd |= COMMAND_GO | COMMAND_CE(ctrl->cur_cs);
>> >> + writel_relaxed(cmd, ctrl->regs + COMMAND);
>> >> + ret = wait_for_completion_io_timeout(&ctrl->command_complete,
>> >> + msecs_to_jiffies(500));
>> >
>> > It's not obvious to me whether _io_ variant is appropriate to use here, would
>> > be nice if somebody could clarify that. Maybe block/ already does the IO
>> > accounting itself and hence the IO time would be counted twice in that case.
>>
>> Good that you bring this up.
>>
>> I don't think that there is any higher layer which could take care of
>> accounting. Usually, with raw nand there is no block layer involved
>> anyway.
>>
>> In a quick test it seems that only when using wait_for_completion_io I/O
>> is properly accounted in the "wait" section of top.
>>
>> So far only a single driver (omap2) used the _io variant, but I think it
>> is the right thing to do! After all, it is I/O...
>>
>> Boris or any other MTD maintainer, any comment on this?
>
> Given this definition of io_schedule_timeout() [1] (which is used when
> you call wait_for_completion_io_timeout()), I'd say it's not useful to
> use the _io_ version, simply because MTD devs are not exposed as blk
> devices, and thus don't need the blk_schedule_flush_plug() that is done
> is io_schedule_prepare(). But that also means MTD I/Os are not
> accounted as I/Os :-(.
Documentation of wait_for_completion_io says:
"The caller is accounted as waiting for IO (which traditionally means
blkio only)."
Which sounds as if it using _io is only an accounting thing...
The hint about blkio might suggest that there is more to it.
Is calling blk_schedule_flush_plug a problem for MTD?
https://elixir.bootlin.com/linux/v4.17.1/source/include/linux/blkdev.h#L1355
>
> Let's go for the non-io version for now, since all drivers except omap2
> seem to use this function.
>
I still think it would be nice and "the right thing" from a user
perspective...
--
Stefan
> [1]https://elixir.bootlin.com/linux/v4.17.1/source/kernel/sched/core.c#L5164
next prev parent reply other threads:[~2018-06-12 9:17 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-11 20:52 [PATCH v4 0/6] mtd: rawnand: add NVIDIA Tegra NAND flash support Stefan Agner
2018-06-11 20:52 ` [PATCH v4 1/6] mtd: rawnand: add Reed-Solomon error correction algorithm Stefan Agner
2018-06-12 18:37 ` Rob Herring
2018-06-11 20:52 ` [PATCH v4 2/6] mtd: rawnand: add an option to specify NAND chip as a boot device Stefan Agner
2018-06-11 20:52 ` [PATCH v4 3/6] mtd: rawnand: tegra: add devicetree binding Stefan Agner
2018-06-11 20:52 ` [PATCH v4 4/6] mtd: rawnand: add NVIDIA Tegra NAND Flash controller driver Stefan Agner
2018-06-11 23:08 ` kbuild test robot
2018-06-11 23:32 ` Dmitry Osipenko
2018-06-12 8:02 ` Stefan Agner
2018-06-12 8:13 ` Boris Brezillon
2018-06-17 16:57 ` Stefan Agner
2018-06-12 0:03 ` Dmitry Osipenko
2018-06-12 8:06 ` Stefan Agner
2018-06-12 8:27 ` Boris Brezillon
2018-06-12 9:17 ` Stefan Agner [this message]
2018-06-12 9:34 ` Boris Brezillon
2018-06-12 15:24 ` Jens Axboe
2018-06-12 20:20 ` Stefan Agner
2018-06-12 21:20 ` Boris Brezillon
2018-06-12 21:24 ` Jens Axboe
2018-06-12 21:30 ` Boris Brezillon
2018-06-12 12:17 ` Dmitry Osipenko
2018-06-11 20:52 ` [PATCH v4 5/6] ARM: dts: tegra: add Tegra20 NAND flash controller node Stefan Agner
2018-06-11 20:52 ` [PATCH v4 6/6] ARM: dts: tegra: enable NAND flash on Colibri T20 Stefan Agner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=53e36cff80e38e489959aa18471d0782@agner.ch \
--to=stefan@agner.ch \
--cc=axboe@kernel.dk \
--cc=benjamin.lindqvist@endian.se \
--cc=boris.brezillon@bootlin.com \
--cc=computersforpeace@gmail.com \
--cc=dev@lynxeye.de \
--cc=devicetree@vger.kernel.org \
--cc=digetx@gmail.com \
--cc=dwmw2@infradead.org \
--cc=gaireg@gaireg.de \
--cc=jonathanh@nvidia.com \
--cc=krzk@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=linux-tegra@vger.kernel.org \
--cc=marcel@ziswiler.com \
--cc=marek.vasut@gmail.com \
--cc=mark.rutland@arm.com \
--cc=miquel.raynal@bootlin.com \
--cc=mirza.krak@gmail.com \
--cc=pdeschrijver@nvidia.com \
--cc=pgaikwad@nvidia.com \
--cc=richard@nod.at \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).