linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [Patch v4 0/6] Introduce Thermal Pressure
@ 2019-10-22 20:34 Thara Gopinath
  2019-10-22 20:34 ` [Patch v4 1/6] sched/pelt.c: Add support to track thermal pressure Thara Gopinath
                   ` (7 more replies)
  0 siblings, 8 replies; 51+ messages in thread
From: Thara Gopinath @ 2019-10-22 20:34 UTC (permalink / raw)
  To: mingo, peterz, ionela.voinescu, vincent.guittot, rui.zhang,
	edubezval, qperret
  Cc: linux-kernel, amit.kachhap, javi.merino, daniel.lezcano

Thermal governors can respond to an overheat event of a cpu by
capping the cpu's maximum possible frequency. This in turn
means that the maximum available compute capacity of the
cpu is restricted. But today in the kernel, task scheduler is 
not notified of capping of maximum frequency of a cpu.
In other words, scheduler is unware of maximum capacity
restrictions placed on a cpu due to thermal activity.
This patch series attempts to address this issue.
The benefits identified are better task placement among available
cpus in event of overheating which in turn leads to better
performance numbers.

The reduction in the maximum possible capacity of a cpu due to a 
thermal event can be considered as thermal pressure. Instantaneous
thermal pressure is hard to record and can sometime be erroneous
as there can be mismatch between the actual capping of capacity
and scheduler recording it. Thus solution is to have a weighted
average per cpu value for thermal pressure over time.
The weight reflects the amount of time the cpu has spent at a
capped maximum frequency. Since thermal pressure is recorded as
an average, it must be decayed periodically. Exisiting algorithm
in the kernel scheduler pelt framework is re-used to calculate
the weighted average. This patch series also defines a sysctl
inerface to allow for a configurable decay period.

Regarding testing, basic build, boot and sanity testing have been
performed on db845c platform with debian file system.
Further, dhrystone and hackbench tests have been
run with the thermal pressure algorithm. During testing, due to
constraints of step wise governor in dealing with big little systems,
trip point 0 temperature was made assymetric between cpus in little
cluster and big cluster; the idea being that
big core will heat up and cpu cooling device will throttle the
frequency of the big cores faster, there by limiting the maximum available
capacity and the scheduler will spread out tasks to little cores as well.

Test Results

Hackbench: 1 group , 30000 loops, 10 runs       
                                               Result         SD             
                                               (Secs)     (% of mean)     
 No Thermal Pressure                            14.03       2.69%           
 Thermal Pressure PELT Algo. Decay : 32 ms      13.29       0.56%         
 Thermal Pressure PELT Algo. Decay : 64 ms      12.57       1.56%           
 Thermal Pressure PELT Algo. Decay : 128 ms     12.71       1.04%         
 Thermal Pressure PELT Algo. Decay : 256 ms     12.29       1.42%           
 Thermal Pressure PELT Algo. Decay : 512 ms     12.42       1.15%  

Dhrystone Run Time  : 20 threads, 3000 MLOOPS
                                                 Result      SD             
                                                 (Secs)    (% of mean)     
 No Thermal Pressure                              9.452      4.49%
 Thermal Pressure PELT Algo. Decay : 32 ms        8.793      5.30%
 Thermal Pressure PELT Algo. Decay : 64 ms        8.981      5.29%
 Thermal Pressure PELT Algo. Decay : 128 ms       8.647      6.62%
 Thermal Pressure PELT Algo. Decay : 256 ms       8.774      6.45%
 Thermal Pressure PELT Algo. Decay : 512 ms       8.603      5.41%  

A Brief History

The first version of this patch-series was posted with resuing
PELT algorithm to decay thermal pressure signal. The discussions
that followed were around whether intanteneous thermal pressure
solution is better and whether a stand-alone algortihm to accumulate
and decay thermal pressure is more appropriate than re-using the
PELT framework. 
Tests on Hikey960 showed the stand-alone algorithm performing slightly
better than resuing PELT algorithm and V2 was posted with the stand
alone algorithm. Test results were shared as part of this series.
Discussions were around re-using PELT algorithm and running
further tests with more granular decay period.

For some time after this development was impeded due to hardware
unavailability, some other unforseen and possibly unfortunate events.
For this version, h/w was switched from hikey960 to db845c.
Also Instantaneous thermal pressure was never tested as part of this
cycle as it is clear that weighted average is a better implementation.
The non-PELT algorithm never gave any conclusive results to prove that it
is better than reusing PELT algorithm, in this round of testing.
Also reusing PELT algorithm means thermal pressure tracks the
other utilization signals in the scheduler.

v3->v4:
	- "Patch 3/7:sched: Initialize per cpu thermal pressure structure"
	   is dropped as it is no longer needed following changes in other
	   other patches.
	- rest of the change log mentioned in specific patches.

Thara Gopinath (6):
  sched/pelt.c: Add support to track thermal pressure
  sched: Add infrastructure to store and update instantaneous thermal
    pressure
  sched/fair: Enable CFS periodic tick to update thermal pressure
  sched/fair: update cpu_capcity to reflect thermal pressure
  thermal/cpu-cooling: Update thermal pressure in case of a maximum
    frequency capping
  sched: thermal: Enable tuning of decay period

 Documentation/admin-guide/kernel-parameters.txt |  5 ++
 drivers/thermal/cpu_cooling.c                   | 31 ++++++++++-
 include/linux/sched.h                           |  8 +++
 kernel/sched/Makefile                           |  2 +-
 kernel/sched/fair.c                             |  6 +++
 kernel/sched/pelt.c                             | 13 +++++
 kernel/sched/pelt.h                             |  7 +++
 kernel/sched/sched.h                            |  1 +
 kernel/sched/thermal.c                          | 68 +++++++++++++++++++++++++
 kernel/sched/thermal.h                          | 13 +++++
 10 files changed, 151 insertions(+), 3 deletions(-)
 create mode 100644 kernel/sched/thermal.c
 create mode 100644 kernel/sched/thermal.h

-- 
2.1.4


^ permalink raw reply	[flat|nested] 51+ messages in thread

end of thread, other threads:[~2019-11-05 21:29 UTC | newest]

Thread overview: 51+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-10-22 20:34 [Patch v4 0/6] Introduce Thermal Pressure Thara Gopinath
2019-10-22 20:34 ` [Patch v4 1/6] sched/pelt.c: Add support to track thermal pressure Thara Gopinath
2019-10-31  9:47   ` Ionela Voinescu
2019-10-22 20:34 ` [Patch v4 2/6] sched: Add infrastructure to store and update instantaneous " Thara Gopinath
2019-10-28 15:21   ` Peter Zijlstra
2019-10-30 21:37     ` Thara Gopinath
2019-11-01 12:17   ` Dietmar Eggemann
2019-11-01 20:57     ` Thara Gopinath
2019-11-04 17:29       ` Dietmar Eggemann
2019-11-04 17:34         ` Vincent Guittot
2019-11-04 17:41           ` Dietmar Eggemann
2019-11-04 17:48             ` Vincent Guittot
2019-10-22 20:34 ` [Patch v4 3/6] sched/fair: Enable CFS periodic tick to update " Thara Gopinath
2019-10-28 15:24   ` Peter Zijlstra
2019-10-28 15:27     ` Peter Zijlstra
2019-10-30 21:41     ` Thara Gopinath
2019-10-31 16:11   ` Dietmar Eggemann
2019-10-31 16:46     ` Thara Gopinath
2019-10-22 20:34 ` [Patch v4 4/6] sched/fair: update cpu_capcity to reflect " Thara Gopinath
2019-10-23 12:28   ` Qais Yousef
2019-10-28 15:30     ` Peter Zijlstra
2019-10-31 10:53       ` Qais Yousef
2019-10-31 15:38         ` Dietmar Eggemann
2019-10-31 15:48           ` Vincent Guittot
2019-10-31 16:17             ` Dietmar Eggemann
2019-10-31 16:31               ` Vincent Guittot
2019-10-31 16:44                 ` Dietmar Eggemann
2019-10-31 16:03         ` Thara Gopinath
2019-10-31 16:56           ` Qais Yousef
2019-10-22 20:34 ` [Patch v4 5/6] thermal/cpu-cooling: Update thermal pressure in case of a maximum frequency capping Thara Gopinath
2019-10-28 15:33   ` Peter Zijlstra
2019-10-31 16:29   ` Dietmar Eggemann
2019-10-31 16:38     ` Vincent Guittot
2019-11-01 15:47       ` Ionela Voinescu
2019-11-01 21:04         ` Thara Gopinath
2019-11-04 14:41           ` Ionela Voinescu
2019-10-31 16:46     ` Thara Gopinath
2019-10-22 20:34 ` [Patch v4 6/6] sched: thermal: Enable tuning of decay period Thara Gopinath
2019-10-28 15:42   ` Peter Zijlstra
2019-11-04 16:12   ` Ionela Voinescu
2019-11-05 20:26     ` Thara Gopinath
2019-11-05 21:29       ` Ionela Voinescu
2019-10-29 15:34 ` [Patch v4 0/6] Introduce Thermal Pressure Daniel Lezcano
2019-10-31 10:07   ` Ionela Voinescu
2019-10-31 11:54     ` Daniel Lezcano
2019-10-31 12:57       ` Ionela Voinescu
2019-10-31 17:48         ` Daniel Lezcano
2019-10-31  9:44 ` Ionela Voinescu
2019-10-31 16:41   ` Thara Gopinath
2019-10-31 16:52     ` Thara Gopinath
2019-11-05 21:04     ` Ionela Voinescu

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).