[PATCH 0/2] drm: bridge: adv7511: Add support For ADV7535

[PATCH 0/2] drm: bridge: adv7511: Add support For ADV7535

[Bogdan Togorean]

This patch-set add support for ADV7535 part in ADV7511 driver.

ADV7535 and ADV7533 are pin to pin compatible parts but ADV7535
support TMDS clock upto 148.5Mhz and resolutions up to 1080p@60Hz.

Bogdan Togorean (2):
  dt-bindings: drm: bridge: adv7511: Add ADV7535 support
  drm: bridge: adv7511: Add support for ADV7535

 .../bindings/display/bridge/adi,adv7511.txt   | 23 +++++++-------
 drivers/gpu/drm/bridge/adv7511/adv7511.h      |  2 ++
 drivers/gpu/drm/bridge/adv7511/adv7511_drv.c  | 31 ++++++++++++++-----
 3 files changed, 37 insertions(+), 19 deletions(-)

-- 
2.22.0

[PATCH 1/2] dt-bindings: drm: bridge: adv7511: Add ADV7535 support

[Bogdan Togorean]

ADV7535 is a part compatible with ADV7533 but it supports 1080p@60hz and
v1p2 supply is fixed to 1.8V

Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
---
 .../bindings/display/bridge/adi,adv7511.txt   | 23 ++++++++++---------
 1 file changed, 12 insertions(+), 11 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
index 2c887536258c..e8ddec5d9d91 100644
--- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
@@ -1,10 +1,10 @@
-Analog Device ADV7511(W)/13/33 HDMI Encoders
+Analog Device ADV7511(W)/13/33/35 HDMI Encoders
 -----------------------------------------
 
-The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters
-compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
-S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while
-the others support RGB interface.
+The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
+transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
+conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
+pixels, while the others support RGB interface.
 
 Required properties:
 
@@ -13,6 +13,7 @@ Required properties:
 		"adi,adv7511w"
 		"adi,adv7513"
 		"adi,adv7533"
+		"adi,adv7535"
 
 - reg: I2C slave addresses
   The ADV7511 internal registers are split into four pages exposed through
@@ -52,14 +53,14 @@ The following input format properties are required except in "rgb 1x" and
 - bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
   needed only for ADV7511.
 
-The following properties are required for ADV7533:
+The following properties are required for ADV7533 and ADV7535:
 
 - adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
   be one of 1, 2, 3 or 4.
 - a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
 - v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
 - v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
-  either 1.2V or 1.8V.
+  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
 
 Optional properties:
 
@@ -71,9 +72,9 @@ Optional properties:
 - adi,embedded-sync: The input uses synchronization signals embedded in the
   data stream (similar to BT.656). Defaults to separate H/V synchronization
   signals.
-- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing
-  generator. The chip will rely on the sync signals in the DSI data lanes,
-  rather than generate its own timings for HDMI output.
+- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
+  internal timing generator. The chip will rely on the sync signals in the
+  DSI data lanes, rather than generate its own timings for HDMI output.
 - clocks: from common clock binding: reference to the CEC clock.
 - clock-names: from common clock binding: must be "cec".
 - reg-names : Names of maps with programmable addresses.
@@ -85,7 +86,7 @@ Required nodes:
 The ADV7511 has two video ports. Their connections are modelled using the OF
 graph bindings specified in Documentation/devicetree/bindings/graph.txt.
 
-- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the
+- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
   remote endpoint phandle should be a reference to a valid mipi_dsi_host device
   node.
 - Video port 1 for the HDMI output
-- 
2.22.0

[PATCH 2/2] drm: bridge: adv7511: Add support for ADV7535

[Bogdan Togorean]

ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535 but on ADV7533 can be 1.2V
or 1.8V and is configurable in a register.

Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
---
 drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 ++
 drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 31 +++++++++++++++-----
 2 files changed, 25 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
index 52b2adfdc877..702432615ec8 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
@@ -91,6 +91,7 @@
 #define ADV7511_REG_ARC_CTRL			0xdf
 #define ADV7511_REG_CEC_I2C_ADDR		0xe1
 #define ADV7511_REG_CEC_CTRL			0xe2
+#define ADV7511_REG_SUPPLY_SELECT		0xe4
 #define ADV7511_REG_CHIP_ID_HIGH		0xf5
 #define ADV7511_REG_CHIP_ID_LOW			0xf6
 
@@ -320,6 +321,7 @@ struct adv7511_video_config {
 enum adv7511_type {
 	ADV7511,
 	ADV7533,
+	ADV7535,
 };
 
 #define ADV7511_MAX_ADDRS 3
diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
index f6d2681f6927..941072decb73 100644
--- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
+++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
@@ -367,7 +367,7 @@ static void adv7511_power_on(struct adv7511 *adv7511)
 	 */
 	regcache_sync(adv7511->regmap);
 
-	if (adv7511->type == ADV7533)
+	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		adv7533_dsi_power_on(adv7511);
 	adv7511->powered = true;
 }
@@ -387,7 +387,7 @@ static void __adv7511_power_off(struct adv7511 *adv7511)
 static void adv7511_power_off(struct adv7511 *adv7511)
 {
 	__adv7511_power_off(adv7511);
-	if (adv7511->type == ADV7533)
+	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		adv7533_dsi_power_off(adv7511);
 	adv7511->powered = false;
 }
@@ -761,7 +761,7 @@ static void adv7511_mode_set(struct adv7511 *adv7511,
 	regmap_update_bits(adv7511->regmap, 0x17,
 		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
 
-	if (adv7511->type == ADV7533)
+	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		adv7533_mode_set(adv7511, adj_mode);
 
 	drm_mode_copy(&adv7511->curr_mode, adj_mode);
@@ -874,7 +874,7 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge)
 				 &adv7511_connector_helper_funcs);
 	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
 
-	if (adv->type == ADV7533)
+	if (adv->type == ADV7533 || adv->type == ADV7535)
 		ret = adv7533_attach_dsi(adv);
 
 	if (adv->i2c_main->irq)
@@ -952,7 +952,7 @@ static bool adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
 	struct i2c_client *i2c = to_i2c_client(dev);
 	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
 
-	if (adv7511->type == ADV7533)
+	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		reg -= ADV7533_REG_CEC_OFFSET;
 
 	switch (reg) {
@@ -994,7 +994,7 @@ static int adv7511_init_cec_regmap(struct adv7511 *adv)
 		goto err;
 	}
 
-	if (adv->type == ADV7533) {
+	if (adv->type == ADV7533 || adv->type == ADV7535) {
 		ret = adv7533_patch_cec_registers(adv);
 		if (ret)
 			goto err;
@@ -1094,8 +1094,9 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 	struct adv7511_link_config link_config;
 	struct adv7511 *adv7511;
 	struct device *dev = &i2c->dev;
+	struct regulator *reg_v1p2;
 	unsigned int val;
-	int ret;
+	int ret, reg_v1p2_uV;
 
 	if (!dev->of_node)
 		return -EINVAL;
@@ -1163,6 +1164,18 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 	if (ret)
 		goto uninit_regulators;
 
+	if (adv7511->type == ADV7533) {
+		ret = match_string(adv7533_supply_names, adv7511->num_supplies,
+									"v1p2");
+		reg_v1p2 = adv7511->supplies[ret].consumer;
+		reg_v1p2_uV = regulator_get_voltage(reg_v1p2);
+
+		if (reg_v1p2_uV == 1200000) {
+			regmap_update_bits(adv7511->regmap,
+				ADV7511_REG_SUPPLY_SELECT, 0x80, 0x80);
+		}
+	}
+
 	adv7511_packet_disable(adv7511, 0xffff);
 
 	adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
@@ -1242,7 +1255,7 @@ static int adv7511_remove(struct i2c_client *i2c)
 {
 	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
 
-	if (adv7511->type == ADV7533)
+	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
 		adv7533_detach_dsi(adv7511);
 	i2c_unregister_device(adv7511->i2c_cec);
 	if (adv7511->cec_clk)
@@ -1268,6 +1281,7 @@ static const struct i2c_device_id adv7511_i2c_ids[] = {
 	{ "adv7513", ADV7511 },
 #ifdef CONFIG_DRM_I2C_ADV7533
 	{ "adv7533", ADV7533 },
+	{ "adv7535", ADV7535 },
 #endif
 	{ }
 };
@@ -1279,6 +1293,7 @@ static const struct of_device_id adv7511_of_ids[] = {
 	{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
 #ifdef CONFIG_DRM_I2C_ADV7533
 	{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
+	{ .compatible = "adi,adv7535", .data = (void *)ADV7535 },
 #endif
 	{ }
 };
-- 
2.22.0

Re: [PATCH 2/2] drm: bridge: adv7511: Add support for ADV7535

[Neil Armstrong]

Hi Bogdan,

On 30/07/2019 15:17, Bogdan Togorean wrote:
> ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
> 1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535 but on ADV7533 can be 1.2V
> or 1.8V and is configurable in a register.
> 
> Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
> ---
>  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 ++
>  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 31 +++++++++++++++-----
>  2 files changed, 25 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> index 52b2adfdc877..702432615ec8 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> @@ -91,6 +91,7 @@
>  #define ADV7511_REG_ARC_CTRL			0xdf
>  #define ADV7511_REG_CEC_I2C_ADDR		0xe1
>  #define ADV7511_REG_CEC_CTRL			0xe2
> +#define ADV7511_REG_SUPPLY_SELECT		0xe4
>  #define ADV7511_REG_CHIP_ID_HIGH		0xf5
>  #define ADV7511_REG_CHIP_ID_LOW			0xf6
>  
> @@ -320,6 +321,7 @@ struct adv7511_video_config {
>  enum adv7511_type {
>  	ADV7511,
>  	ADV7533,
> +	ADV7535,
>  };
>  
>  #define ADV7511_MAX_ADDRS 3
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> index f6d2681f6927..941072decb73 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> @@ -367,7 +367,7 @@ static void adv7511_power_on(struct adv7511 *adv7511)
>  	 */
>  	regcache_sync(adv7511->regmap);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_dsi_power_on(adv7511);
>  	adv7511->powered = true;
>  }
> @@ -387,7 +387,7 @@ static void __adv7511_power_off(struct adv7511 *adv7511)
>  static void adv7511_power_off(struct adv7511 *adv7511)
>  {
>  	__adv7511_power_off(adv7511);
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_dsi_power_off(adv7511);
>  	adv7511->powered = false;
>  }
> @@ -761,7 +761,7 @@ static void adv7511_mode_set(struct adv7511 *adv7511,
>  	regmap_update_bits(adv7511->regmap, 0x17,
>  		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_mode_set(adv7511, adj_mode);
>  
>  	drm_mode_copy(&adv7511->curr_mode, adj_mode);
> @@ -874,7 +874,7 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge)
>  				 &adv7511_connector_helper_funcs);
>  	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
>  
> -	if (adv->type == ADV7533)
> +	if (adv->type == ADV7533 || adv->type == ADV7535)
>  		ret = adv7533_attach_dsi(adv);
>  
>  	if (adv->i2c_main->irq)
> @@ -952,7 +952,7 @@ static bool adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
>  	struct i2c_client *i2c = to_i2c_client(dev);
>  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		reg -= ADV7533_REG_CEC_OFFSET;
>  
>  	switch (reg) {
> @@ -994,7 +994,7 @@ static int adv7511_init_cec_regmap(struct adv7511 *adv)
>  		goto err;
>  	}
>  
> -	if (adv->type == ADV7533) {
> +	if (adv->type == ADV7533 || adv->type == ADV7535) {
>  		ret = adv7533_patch_cec_registers(adv);
>  		if (ret)
>  			goto err;
> @@ -1094,8 +1094,9 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
>  	struct adv7511_link_config link_config;
>  	struct adv7511 *adv7511;
>  	struct device *dev = &i2c->dev;
> +	struct regulator *reg_v1p2;
>  	unsigned int val;
> -	int ret;
> +	int ret, reg_v1p2_uV;
>  
>  	if (!dev->of_node)
>  		return -EINVAL;
> @@ -1163,6 +1164,18 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
>  	if (ret)
>  		goto uninit_regulators;
>  
> +	if (adv7511->type == ADV7533) {
> +		ret = match_string(adv7533_supply_names, adv7511->num_supplies,
> +									"v1p2");
> +		reg_v1p2 = adv7511->supplies[ret].consumer;
> +		reg_v1p2_uV = regulator_get_voltage(reg_v1p2);
> +
> +		if (reg_v1p2_uV == 1200000) {
> +			regmap_update_bits(adv7511->regmap,
> +				ADV7511_REG_SUPPLY_SELECT, 0x80, 0x80);
> +		}
> +	}
> +
>  	adv7511_packet_disable(adv7511, 0xffff);
>  
>  	adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
> @@ -1242,7 +1255,7 @@ static int adv7511_remove(struct i2c_client *i2c)
>  {
>  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_detach_dsi(adv7511);
>  	i2c_unregister_device(adv7511->i2c_cec);
>  	if (adv7511->cec_clk)
> @@ -1268,6 +1281,7 @@ static const struct i2c_device_id adv7511_i2c_ids[] = {
>  	{ "adv7513", ADV7511 },
>  #ifdef CONFIG_DRM_I2C_ADV7533
>  	{ "adv7533", ADV7533 },
> +	{ "adv7535", ADV7535 },

Maybe you should add a new CONFIG_DRM_I2C_ADV7535 or update the current CONFIG_DRM_I2C_ADV7533 description.

>  #endif
>  	{ }
>  };
> @@ -1279,6 +1293,7 @@ static const struct of_device_id adv7511_of_ids[] = {
>  	{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
>  #ifdef CONFIG_DRM_I2C_ADV7533
>  	{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
> +	{ .compatible = "adi,adv7535", .data = (void *)ADV7535 },

Ditto

I'm not a adv75xx expert but it looks sane.

Neil

>  #endif
>  	{ }
>  };
> 

Re: [PATCH 1/2] dt-bindings: drm: bridge: adv7511: Add ADV7535 support

[Laurent Pinchart]

Hi Bogdan,

Thank you for the patch.

On Tue, Jul 30, 2019 at 04:17:35PM +0300, Bogdan Togorean wrote:
> ADV7535 is a part compatible with ADV7533 but it supports 1080p@60hz and
> v1p2 supply is fixed to 1.8V
> 
> Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  .../bindings/display/bridge/adi,adv7511.txt   | 23 ++++++++++---------
>  1 file changed, 12 insertions(+), 11 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> index 2c887536258c..e8ddec5d9d91 100644
> --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
> @@ -1,10 +1,10 @@
> -Analog Device ADV7511(W)/13/33 HDMI Encoders
> +Analog Device ADV7511(W)/13/33/35 HDMI Encoders
>  -----------------------------------------
>  
> -The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters
> -compatible with HDMI 1.4 and DVI 1.0. They support color space conversion,
> -S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while
> -the others support RGB interface.
> +The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video
> +transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space
> +conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input
> +pixels, while the others support RGB interface.
>  
>  Required properties:
>  
> @@ -13,6 +13,7 @@ Required properties:
>  		"adi,adv7511w"
>  		"adi,adv7513"
>  		"adi,adv7533"
> +		"adi,adv7535"
>  
>  - reg: I2C slave addresses
>    The ADV7511 internal registers are split into four pages exposed through
> @@ -52,14 +53,14 @@ The following input format properties are required except in "rgb 1x" and
>  - bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is
>    needed only for ADV7511.
>  
> -The following properties are required for ADV7533:
> +The following properties are required for ADV7533 and ADV7535:
>  
>  - adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should
>    be one of 1, 2, 3 or 4.
>  - a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip.
>  - v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip.
>  - v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be
> -  either 1.2V or 1.8V.
> +  either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535.
>  
>  Optional properties:
>  
> @@ -71,9 +72,9 @@ Optional properties:
>  - adi,embedded-sync: The input uses synchronization signals embedded in the
>    data stream (similar to BT.656). Defaults to separate H/V synchronization
>    signals.
> -- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing
> -  generator. The chip will rely on the sync signals in the DSI data lanes,
> -  rather than generate its own timings for HDMI output.
> +- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the
> +  internal timing generator. The chip will rely on the sync signals in the
> +  DSI data lanes, rather than generate its own timings for HDMI output.
>  - clocks: from common clock binding: reference to the CEC clock.
>  - clock-names: from common clock binding: must be "cec".
>  - reg-names : Names of maps with programmable addresses.
> @@ -85,7 +86,7 @@ Required nodes:
>  The ADV7511 has two video ports. Their connections are modelled using the OF
>  graph bindings specified in Documentation/devicetree/bindings/graph.txt.
>  
> -- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the
> +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the
>    remote endpoint phandle should be a reference to a valid mipi_dsi_host device
>    node.
>  - Video port 1 for the HDMI output

-- 
Regards,

Laurent Pinchart

Re: [PATCH 2/2] drm: bridge: adv7511: Add support for ADV7535

[Laurent Pinchart]

Hi Bogdan,

Thank you for the patch.

On Tue, Jul 30, 2019 at 04:17:36PM +0300, Bogdan Togorean wrote:
> ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
> 1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535 but on ADV7533 can be 1.2V
> or 1.8V and is configurable in a register.
> 
> Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
> ---
>  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 ++
>  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 31 +++++++++++++++-----
>  2 files changed, 25 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> index 52b2adfdc877..702432615ec8 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> @@ -91,6 +91,7 @@
>  #define ADV7511_REG_ARC_CTRL			0xdf
>  #define ADV7511_REG_CEC_I2C_ADDR		0xe1
>  #define ADV7511_REG_CEC_CTRL			0xe2
> +#define ADV7511_REG_SUPPLY_SELECT		0xe4
>  #define ADV7511_REG_CHIP_ID_HIGH		0xf5
>  #define ADV7511_REG_CHIP_ID_LOW			0xf6
>  
> @@ -320,6 +321,7 @@ struct adv7511_video_config {
>  enum adv7511_type {
>  	ADV7511,
>  	ADV7533,
> +	ADV7535,
>  };
>  
>  #define ADV7511_MAX_ADDRS 3
> diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> index f6d2681f6927..941072decb73 100644
> --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> @@ -367,7 +367,7 @@ static void adv7511_power_on(struct adv7511 *adv7511)
>  	 */
>  	regcache_sync(adv7511->regmap);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_dsi_power_on(adv7511);
>  	adv7511->powered = true;
>  }
> @@ -387,7 +387,7 @@ static void __adv7511_power_off(struct adv7511 *adv7511)
>  static void adv7511_power_off(struct adv7511 *adv7511)
>  {
>  	__adv7511_power_off(adv7511);
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_dsi_power_off(adv7511);
>  	adv7511->powered = false;
>  }
> @@ -761,7 +761,7 @@ static void adv7511_mode_set(struct adv7511 *adv7511,
>  	regmap_update_bits(adv7511->regmap, 0x17,
>  		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_mode_set(adv7511, adj_mode);
>  
>  	drm_mode_copy(&adv7511->curr_mode, adj_mode);
> @@ -874,7 +874,7 @@ static int adv7511_bridge_attach(struct drm_bridge *bridge)
>  				 &adv7511_connector_helper_funcs);
>  	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
>  
> -	if (adv->type == ADV7533)
> +	if (adv->type == ADV7533 || adv->type == ADV7535)
>  		ret = adv7533_attach_dsi(adv);
>  
>  	if (adv->i2c_main->irq)
> @@ -952,7 +952,7 @@ static bool adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
>  	struct i2c_client *i2c = to_i2c_client(dev);
>  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		reg -= ADV7533_REG_CEC_OFFSET;
>  
>  	switch (reg) {
> @@ -994,7 +994,7 @@ static int adv7511_init_cec_regmap(struct adv7511 *adv)
>  		goto err;
>  	}
>  
> -	if (adv->type == ADV7533) {
> +	if (adv->type == ADV7533 || adv->type == ADV7535) {
>  		ret = adv7533_patch_cec_registers(adv);
>  		if (ret)
>  			goto err;
> @@ -1094,8 +1094,9 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
>  	struct adv7511_link_config link_config;
>  	struct adv7511 *adv7511;
>  	struct device *dev = &i2c->dev;
> +	struct regulator *reg_v1p2;
>  	unsigned int val;
> -	int ret;
> +	int ret, reg_v1p2_uV;
>  
>  	if (!dev->of_node)
>  		return -EINVAL;
> @@ -1163,6 +1164,18 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
>  	if (ret)
>  		goto uninit_regulators;
>  
> +	if (adv7511->type == ADV7533) {
> +		ret = match_string(adv7533_supply_names, adv7511->num_supplies,

Although they're equivalent, I would use
ARRAY_SIZE(adv7533_supply_names) instead of adv7511->num_supplies to
make the code easier to read (otherwise one has to check where
num_supplies is set to validate this function call).

> +									"v1p2");

You should align "v1p2" left, with adv7533_supply_names.

I wonder if you couldn't simply hardcode the index, with a comment above
the adv7533_supply_names array to mention that the order of the entries
shall not be modified without updating the locations that hardcode
indices.

> +		reg_v1p2 = adv7511->supplies[ret].consumer;
> +		reg_v1p2_uV = regulator_get_voltage(reg_v1p2);
> +
> +		if (reg_v1p2_uV == 1200000) {
> +			regmap_update_bits(adv7511->regmap,
> +				ADV7511_REG_SUPPLY_SELECT, 0x80, 0x80);
> +		}

Shouldn't you explicitly clear bit 7 when reg_v1p2_uV is not 1200000 ?
Or is there a guarantee it gets reset after a reboot ?

> +	}
> +
>  	adv7511_packet_disable(adv7511, 0xffff);
>  
>  	adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
> @@ -1242,7 +1255,7 @@ static int adv7511_remove(struct i2c_client *i2c)
>  {
>  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
>  
> -	if (adv7511->type == ADV7533)
> +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
>  		adv7533_detach_dsi(adv7511);
>  	i2c_unregister_device(adv7511->i2c_cec);
>  	if (adv7511->cec_clk)
> @@ -1268,6 +1281,7 @@ static const struct i2c_device_id adv7511_i2c_ids[] = {
>  	{ "adv7513", ADV7511 },
>  #ifdef CONFIG_DRM_I2C_ADV7533

As noted by Neil, I think this config option should be renamed (possibly
to CONFIG_DRM_I2C_ADV753X) and its description updated.

>  	{ "adv7533", ADV7533 },
> +	{ "adv7535", ADV7535 },
>  #endif
>  	{ }
>  };
> @@ -1279,6 +1293,7 @@ static const struct of_device_id adv7511_of_ids[] = {
>  	{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
>  #ifdef CONFIG_DRM_I2C_ADV7533
>  	{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
> +	{ .compatible = "adi,adv7535", .data = (void *)ADV7535 },
>  #endif
>  	{ }
>  };

-- 
Regards,

Laurent Pinchart

Re: [PATCH 2/2] drm: bridge: adv7511: Add support for ADV7535

[Togorean, Bogdan]

Hi Neil,

Thank you for review.

On Wed, 2019-07-31 at 09:42 +0200, Neil Armstrong wrote:
> [External]
> 
> Hi Bogdan,
> 
> On 30/07/2019 15:17, Bogdan Togorean wrote:
> > ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
> > 1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535 but on ADV7533 can be
> > 1.2V
> > or 1.8V and is configurable in a register.
> > 
> > Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
> > ---
> >  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 ++
> >  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 31 +++++++++++++++-
> > ----
> >  2 files changed, 25 insertions(+), 8 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > index 52b2adfdc877..702432615ec8 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > @@ -91,6 +91,7 @@
> >  #define ADV7511_REG_ARC_CTRL			0xdf
> >  #define ADV7511_REG_CEC_I2C_ADDR		0xe1
> >  #define ADV7511_REG_CEC_CTRL			0xe2
> > +#define ADV7511_REG_SUPPLY_SELECT		0xe4
> >  #define ADV7511_REG_CHIP_ID_HIGH		0xf5
> >  #define ADV7511_REG_CHIP_ID_LOW			0xf6
> >  
> > @@ -320,6 +321,7 @@ struct adv7511_video_config {
> >  enum adv7511_type {
> >  	ADV7511,
> >  	ADV7533,
> > +	ADV7535,
> >  };
> >  
> >  #define ADV7511_MAX_ADDRS 3
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > index f6d2681f6927..941072decb73 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > @@ -367,7 +367,7 @@ static void adv7511_power_on(struct adv7511
> > *adv7511)
> >  	 */
> >  	regcache_sync(adv7511->regmap);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_dsi_power_on(adv7511);
> >  	adv7511->powered = true;
> >  }
> > @@ -387,7 +387,7 @@ static void __adv7511_power_off(struct adv7511
> > *adv7511)
> >  static void adv7511_power_off(struct adv7511 *adv7511)
> >  {
> >  	__adv7511_power_off(adv7511);
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_dsi_power_off(adv7511);
> >  	adv7511->powered = false;
> >  }
> > @@ -761,7 +761,7 @@ static void adv7511_mode_set(struct adv7511
> > *adv7511,
> >  	regmap_update_bits(adv7511->regmap, 0x17,
> >  		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_mode_set(adv7511, adj_mode);
> >  
> >  	drm_mode_copy(&adv7511->curr_mode, adj_mode);
> > @@ -874,7 +874,7 @@ static int adv7511_bridge_attach(struct
> > drm_bridge *bridge)
> >  				 &adv7511_connector_helper_funcs);
> >  	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
> >  
> > -	if (adv->type == ADV7533)
> > +	if (adv->type == ADV7533 || adv->type == ADV7535)
> >  		ret = adv7533_attach_dsi(adv);
> >  
> >  	if (adv->i2c_main->irq)
> > @@ -952,7 +952,7 @@ static bool
> > adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
> >  	struct i2c_client *i2c = to_i2c_client(dev);
> >  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		reg -= ADV7533_REG_CEC_OFFSET;
> >  
> >  	switch (reg) {
> > @@ -994,7 +994,7 @@ static int adv7511_init_cec_regmap(struct
> > adv7511 *adv)
> >  		goto err;
> >  	}
> >  
> > -	if (adv->type == ADV7533) {
> > +	if (adv->type == ADV7533 || adv->type == ADV7535) {
> >  		ret = adv7533_patch_cec_registers(adv);
> >  		if (ret)
> >  			goto err;
> > @@ -1094,8 +1094,9 @@ static int adv7511_probe(struct i2c_client
> > *i2c, const struct i2c_device_id *id)
> >  	struct adv7511_link_config link_config;
> >  	struct adv7511 *adv7511;
> >  	struct device *dev = &i2c->dev;
> > +	struct regulator *reg_v1p2;
> >  	unsigned int val;
> > -	int ret;
> > +	int ret, reg_v1p2_uV;
> >  
> >  	if (!dev->of_node)
> >  		return -EINVAL;
> > @@ -1163,6 +1164,18 @@ static int adv7511_probe(struct i2c_client
> > *i2c, const struct i2c_device_id *id)
> >  	if (ret)
> >  		goto uninit_regulators;
> >  
> > +	if (adv7511->type == ADV7533) {
> > +		ret = match_string(adv7533_supply_names, adv7511-
> > >num_supplies,
> > +									
> > "v1p2");
> > +		reg_v1p2 = adv7511->supplies[ret].consumer;
> > +		reg_v1p2_uV = regulator_get_voltage(reg_v1p2);
> > +
> > +		if (reg_v1p2_uV == 1200000) {
> > +			regmap_update_bits(adv7511->regmap,
> > +				ADV7511_REG_SUPPLY_SELECT, 0x80, 0x80);
> > +		}
> > +	}
> > +
> >  	adv7511_packet_disable(adv7511, 0xffff);
> >  
> >  	adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
> > @@ -1242,7 +1255,7 @@ static int adv7511_remove(struct i2c_client
> > *i2c)
> >  {
> >  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_detach_dsi(adv7511);
> >  	i2c_unregister_device(adv7511->i2c_cec);
> >  	if (adv7511->cec_clk)
> > @@ -1268,6 +1281,7 @@ static const struct i2c_device_id
> > adv7511_i2c_ids[] = {
> >  	{ "adv7513", ADV7511 },
> >  #ifdef CONFIG_DRM_I2C_ADV7533
> >  	{ "adv7533", ADV7533 },
> > +	{ "adv7535", ADV7535 },
> 
> Maybe you should add a new CONFIG_DRM_I2C_ADV7535 or update the
> current CONFIG_DRM_I2C_ADV7533 description.
I'll rename the config option as Laurent also suggested to
CONFIG_DRM_I2C_ADV753X and update its description. 
> 
> >  #endif
> >  	{ }
> >  };
> > @@ -1279,6 +1293,7 @@ static const struct of_device_id
> > adv7511_of_ids[] = {
> >  	{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
> >  #ifdef CONFIG_DRM_I2C_ADV7533
> >  	{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
> > +	{ .compatible = "adi,adv7535", .data = (void *)ADV7535 },
> 
> Ditto
> 
> I'm not a adv75xx expert but it looks sane.
> 
> Neil
> 
> >  #endif
> >  	{ }
> >  };
> > 

Re: [PATCH 2/2] drm: bridge: adv7511: Add support for ADV7535

[Togorean, Bogdan]

Hi Laurent,

Thnk you for your review.

On Wed, 2019-07-31 at 12:14 +0300, Laurent Pinchart wrote:
> [External]
> 
> Hi Bogdan,
> 
> Thank you for the patch.
> 
> On Tue, Jul 30, 2019 at 04:17:36PM +0300, Bogdan Togorean wrote:
> > ADV7535 is a DSI to HDMI bridge chip like ADV7533 but it allows
> > 1080p@60Hz. v1p2 is fixed to 1.8V on ADV7535 but on ADV7533 can be
> > 1.2V
> > or 1.8V and is configurable in a register.
> > 
> > Signed-off-by: Bogdan Togorean <bogdan.togorean@analog.com>
> > ---
> >  drivers/gpu/drm/bridge/adv7511/adv7511.h     |  2 ++
> >  drivers/gpu/drm/bridge/adv7511/adv7511_drv.c | 31 +++++++++++++++-
> > ----
> >  2 files changed, 25 insertions(+), 8 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > index 52b2adfdc877..702432615ec8 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511.h
> > @@ -91,6 +91,7 @@
> >  #define ADV7511_REG_ARC_CTRL			0xdf
> >  #define ADV7511_REG_CEC_I2C_ADDR		0xe1
> >  #define ADV7511_REG_CEC_CTRL			0xe2
> > +#define ADV7511_REG_SUPPLY_SELECT		0xe4
> >  #define ADV7511_REG_CHIP_ID_HIGH		0xf5
> >  #define ADV7511_REG_CHIP_ID_LOW			0xf6
> >  
> > @@ -320,6 +321,7 @@ struct adv7511_video_config {
> >  enum adv7511_type {
> >  	ADV7511,
> >  	ADV7533,
> > +	ADV7535,
> >  };
> >  
> >  #define ADV7511_MAX_ADDRS 3
> > diff --git a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > index f6d2681f6927..941072decb73 100644
> > --- a/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > +++ b/drivers/gpu/drm/bridge/adv7511/adv7511_drv.c
> > @@ -367,7 +367,7 @@ static void adv7511_power_on(struct adv7511
> > *adv7511)
> >  	 */
> >  	regcache_sync(adv7511->regmap);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_dsi_power_on(adv7511);
> >  	adv7511->powered = true;
> >  }
> > @@ -387,7 +387,7 @@ static void __adv7511_power_off(struct adv7511
> > *adv7511)
> >  static void adv7511_power_off(struct adv7511 *adv7511)
> >  {
> >  	__adv7511_power_off(adv7511);
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_dsi_power_off(adv7511);
> >  	adv7511->powered = false;
> >  }
> > @@ -761,7 +761,7 @@ static void adv7511_mode_set(struct adv7511
> > *adv7511,
> >  	regmap_update_bits(adv7511->regmap, 0x17,
> >  		0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_mode_set(adv7511, adj_mode);
> >  
> >  	drm_mode_copy(&adv7511->curr_mode, adj_mode);
> > @@ -874,7 +874,7 @@ static int adv7511_bridge_attach(struct
> > drm_bridge *bridge)
> >  				 &adv7511_connector_helper_funcs);
> >  	drm_connector_attach_encoder(&adv->connector, bridge->encoder);
> >  
> > -	if (adv->type == ADV7533)
> > +	if (adv->type == ADV7533 || adv->type == ADV7535)
> >  		ret = adv7533_attach_dsi(adv);
> >  
> >  	if (adv->i2c_main->irq)
> > @@ -952,7 +952,7 @@ static bool
> > adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
> >  	struct i2c_client *i2c = to_i2c_client(dev);
> >  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		reg -= ADV7533_REG_CEC_OFFSET;
> >  
> >  	switch (reg) {
> > @@ -994,7 +994,7 @@ static int adv7511_init_cec_regmap(struct
> > adv7511 *adv)
> >  		goto err;
> >  	}
> >  
> > -	if (adv->type == ADV7533) {
> > +	if (adv->type == ADV7533 || adv->type == ADV7535) {
> >  		ret = adv7533_patch_cec_registers(adv);
> >  		if (ret)
> >  			goto err;
> > @@ -1094,8 +1094,9 @@ static int adv7511_probe(struct i2c_client
> > *i2c, const struct i2c_device_id *id)
> >  	struct adv7511_link_config link_config;
> >  	struct adv7511 *adv7511;
> >  	struct device *dev = &i2c->dev;
> > +	struct regulator *reg_v1p2;
> >  	unsigned int val;
> > -	int ret;
> > +	int ret, reg_v1p2_uV;
> >  
> >  	if (!dev->of_node)
> >  		return -EINVAL;
> > @@ -1163,6 +1164,18 @@ static int adv7511_probe(struct i2c_client
> > *i2c, const struct i2c_device_id *id)
> >  	if (ret)
> >  		goto uninit_regulators;
> >  
> > +	if (adv7511->type == ADV7533) {
> > +		ret = match_string(adv7533_supply_names, adv7511-
> > >num_supplies,
> 
> Although they're equivalent, I would use
> ARRAY_SIZE(adv7533_supply_names) instead of adv7511->num_supplies to
> make the code easier to read (otherwise one has to check where
> num_supplies is set to validate this function call).
> 
Ack. Will modify it in V2
> > +									
> > "v1p2");
> 
> You should align "v1p2" left, with adv7533_supply_names.
> 
> I wonder if you couldn't simply hardcode the index, with a comment
> above
> the adv7533_supply_names array to mention that the order of the
> entries
> shall not be modified without updating the locations that hardcode
> indices.
Ok, my intention was to have robust code but as you said a comment
before the supply names array is enough.
> 
> > +		reg_v1p2 = adv7511->supplies[ret].consumer;
> > +		reg_v1p2_uV = regulator_get_voltage(reg_v1p2);
> > +
> > +		if (reg_v1p2_uV == 1200000) {
> > +			regmap_update_bits(adv7511->regmap,
> > +				ADV7511_REG_SUPPLY_SELECT, 0x80, 0x80);
> > +		}
> 
> Shouldn't you explicitly clear bit 7 when reg_v1p2_uV is not 1200000
> ?
> Or is there a guarantee it gets reset after a reboot ?
It is guaranteed that it starts cleared to be safe for the chip if the
voltage is 1.8V.
> 
> > +	}
> > +
> >  	adv7511_packet_disable(adv7511, 0xffff);
> >  
> >  	adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
> > @@ -1242,7 +1255,7 @@ static int adv7511_remove(struct i2c_client
> > *i2c)
> >  {
> >  	struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
> >  
> > -	if (adv7511->type == ADV7533)
> > +	if (adv7511->type == ADV7533 || adv7511->type == ADV7535)
> >  		adv7533_detach_dsi(adv7511);
> >  	i2c_unregister_device(adv7511->i2c_cec);
> >  	if (adv7511->cec_clk)
> > @@ -1268,6 +1281,7 @@ static const struct i2c_device_id
> > adv7511_i2c_ids[] = {
> >  	{ "adv7513", ADV7511 },
> >  #ifdef CONFIG_DRM_I2C_ADV7533
> 
> As noted by Neil, I think this config option should be renamed
> (possibly
> to CONFIG_DRM_I2C_ADV753X) and its description updated.
Ack. Will rename to CONFIG_DRM_I2C_ADV753X and update decription.
> 
> >  	{ "adv7533", ADV7533 },
> > +	{ "adv7535", ADV7535 },
> >  #endif
> >  	{ }
> >  };
> > @@ -1279,6 +1293,7 @@ static const struct of_device_id
> > adv7511_of_ids[] = {
> >  	{ .compatible = "adi,adv7513", .data = (void *)ADV7511 },
> >  #ifdef CONFIG_DRM_I2C_ADV7533
> >  	{ .compatible = "adi,adv7533", .data = (void *)ADV7533 },
> > +	{ .compatible = "adi,adv7535", .data = (void *)ADV7535 },
> >  #endif
> >  	{ }
> >  };