linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Kuogee Hsieh <khsieh@codeaurora.org>,
	robdclark@gmail.com, sean@poorly.run, swboyd@chromium.org,
	vkoul@kernel.org, agross@kernel.org, bjorn.andersson@linaro.org,
	robh+dt@kernel.org, devicetree@vger.kernel.org
Cc: abhinavk@codeaurora.org, aravindh@codeaurora.org,
	freedreno@lists.freedesktop.org, linux-arm-msm@vger.kernel.org,
	linux-kernel@vger.kernel.org, kishon@ti.com,
	p.zabel@pengutronix.de
Subject: Re: [PATCH v2] phy: qcom-qmp: add support for display port voltage and pre-emphasis swing
Date: Fri, 3 Sep 2021 22:09:14 +0300	[thread overview]
Message-ID: <72483937-8ccb-331b-e1af-8f30f6cefc07@linaro.org> (raw)
In-Reply-To: <1630098658-23149-1-git-send-email-khsieh@codeaurora.org>

On 28/08/2021 00:10, Kuogee Hsieh wrote:
> Both voltage and pre-emphasis swing level are set during link training
> negotiation between host and sink. There are totally four tables added.
> A voltage swing table for both hbr and hbr1, a voltage table for both
> hbr2 and hbr3, a pre-emphasis table for both hbr and hbr1 and a pre-emphasis
> table for both hbr2 and hbr3. In addition, write 0x0a to TX_TX_POL_INV is
> added to complete the sequence of configure dp phy base on HPG.
> 
> Chnages in v2:
> -- revise commit test
> -- add Fixes tag
> -- replaced voltage_swing_cfg with voltage
> -- replaced pre_emphasis_cfg with emphasis
> -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_v4_phy_configure_dp_swing()
> -- delete drv_lvl_reg and emp_post_reg parameters from qcom_qmp_phy_configure_dp_swing()
> 
> Fixes: aff188feb5e1 ("phy: qcom-qmp: add support for sm8250-usb3-dp phy")
> Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp.c | 117 ++++++++++++++++++++++++++----------
>   1 file changed, 85 insertions(+), 32 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index 31036aa..021cbb0 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -3546,12 +3546,11 @@ static const u8 qmp_dp_v3_voltage_swing_hbr_rbr[4][4] = {
>   	{ 0x1f, 0xff, 0xff, 0xff }
>   };
>   
> -static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy,
> -		unsigned int drv_lvl_reg, unsigned int emp_post_reg)
> +static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy)

As this becomes a v3-only function, could you please rename it to 
qcom_qmp_v3_phy_configure_dp_swing()

>   {
>   	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
>   	unsigned int v_level = 0, p_level = 0;
> -	u8 voltage_swing_cfg, pre_emphasis_cfg;
> +	u8 voltage, emphasis;
>   	int i;
>   
>   	for (i = 0; i < dp_opts->lanes; i++) {
> @@ -3560,26 +3559,25 @@ static int qcom_qmp_phy_configure_dp_swing(struct qmp_phy *qphy,
>   	}
>   
>   	if (dp_opts->link_rate <= 2700) {
> -		voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level];
> -		pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level];
> +		voltage = qmp_dp_v3_voltage_swing_hbr_rbr[v_level][p_level];
> +		emphasis = qmp_dp_v3_pre_emphasis_hbr_rbr[v_level][p_level];
>   	} else {
> -		voltage_swing_cfg = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level];
> -		pre_emphasis_cfg = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level];
> +		voltage = qmp_dp_v3_voltage_swing_hbr3_hbr2[v_level][p_level];
> +		emphasis = qmp_dp_v3_pre_emphasis_hbr3_hbr2[v_level][p_level];
>   	}
>   
>   	/* TODO: Move check to config check */
> -	if (voltage_swing_cfg == 0xFF && pre_emphasis_cfg == 0xFF)
> +	if (voltage == 0xFF && emphasis == 0xFF)
>   		return -EINVAL;
>   
>   	/* Enable MUX to use Cursor values from these registers */
> -	voltage_swing_cfg |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN;
> -	pre_emphasis_cfg |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN;
> -
> -	writel(voltage_swing_cfg, qphy->tx + drv_lvl_reg);
> -	writel(pre_emphasis_cfg, qphy->tx + emp_post_reg);
> -	writel(voltage_swing_cfg, qphy->tx2 + drv_lvl_reg);
> -	writel(pre_emphasis_cfg, qphy->tx2 + emp_post_reg);
> +	voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN;
> +	emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN;
>   
> +	writel(voltage, qphy->tx + QSERDES_V3_TX_TX_DRV_LVL);
> +	writel(emphasis, qphy->tx + QSERDES_V3_TX_TX_EMP_POST1_LVL);
> +	writel(voltage, qphy->tx2 + QSERDES_V3_TX_TX_DRV_LVL);
> +	writel(emphasis, qphy->tx2 + QSERDES_V3_TX_TX_EMP_POST1_LVL);
>   	return 0;
>   }
>   
> @@ -3588,9 +3586,7 @@ static void qcom_qmp_v3_phy_configure_dp_tx(struct qmp_phy *qphy)
>   	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
>   	u32 bias_en, drvr_en;
>   
> -	if (qcom_qmp_phy_configure_dp_swing(qphy,
> -				QSERDES_V3_TX_TX_DRV_LVL,
> -				QSERDES_V3_TX_TX_EMP_POST1_LVL) < 0)
> +	if (qcom_qmp_phy_configure_dp_swing(qphy) < 0)
>   		return;
>   
>   	if (dp_opts->lanes == 1) {
> @@ -3728,6 +3724,71 @@ static int qcom_qmp_v3_dp_phy_calibrate(struct qmp_phy *qphy)
>   	return 0;
>   }
>   
> +/* The values in these tables are given without MUX_EN (0x20) bit set */
> +static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = {
> +	{ 0x00, 0x0c, 0x15, 0x1b },
> +	{ 0x02, 0x0e, 0x16, 0xff },
> +	{ 0x02, 0x11, 0xff, 0xff },
> +	{ 0x04, 0xff, 0xff, 0xff }
> +};
> +
> +static const u8 qmp_dp_v4_voltage_swing_hbr3_hbr2[4][4] = {
> +	{ 0x02, 0x12, 0x16, 0x1a },
> +	{ 0x09, 0x19, 0x1f, 0xff },
> +	{ 0x10, 0x1f, 0xff, 0xff },
> +	{ 0x1f, 0xff, 0xff, 0xff }
> +};
> +
> +static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = {
> +	{ 0x00, 0x0e, 0x15, 0x1b },
> +	{ 0x00, 0x0e, 0x15, 0xff },
> +	{ 0x00, 0x0e, 0xff, 0xff },
> +	{ 0x04, 0xff, 0xff, 0xff }
> +};
> +
> +static const u8 qmp_dp_v4_voltage_swing_hbr_rbr[4][4] = {
> +	{ 0x08, 0x0f, 0x16, 0x1f },
> +	{ 0x11, 0x1e, 0x1f, 0xff },
> +	{ 0x16, 0x1f, 0xff, 0xff },
> +	{ 0x1f, 0xff, 0xff, 0xff }
> +};
> +
> +static int qcom_qmp_v4_phy_configure_dp_swing(struct qmp_phy *qphy)
> +{
> +	const struct phy_configure_opts_dp *dp_opts = &qphy->dp_opts;
> +	unsigned int v_level = 0, p_level = 0;
> +	u8 voltage, emphasis;
> +	int i;
> +
> +	for (i = 0; i < dp_opts->lanes; i++) {
> +		v_level = max(v_level, dp_opts->voltage[i]);
> +		p_level = max(p_level, dp_opts->pre[i]);
> +	}
> +
> +	if (dp_opts->link_rate <= 2700) {
> +		voltage = qmp_dp_v4_voltage_swing_hbr_rbr[v_level][p_level];
> +		emphasis = qmp_dp_v4_pre_emphasis_hbr_rbr[v_level][p_level];
> +	} else {
> +		voltage = qmp_dp_v4_voltage_swing_hbr3_hbr2[v_level][p_level];
> +		emphasis = qmp_dp_v4_pre_emphasis_hbr3_hbr2[v_level][p_level];
> +	}
> +
> +	/* TODO: Move check to config check */
> +	if (voltage == 0xFF && emphasis == 0xFF)
> +		return -EINVAL;
> +
> +	/* Enable MUX to use Cursor values from these registers */
> +	voltage |= DP_PHY_TXn_TX_DRV_LVL_MUX_EN;
> +	emphasis |= DP_PHY_TXn_TX_EMP_POST1_LVL_MUX_EN;
> +
> +	writel(voltage, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL);
> +	writel(emphasis, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> +	writel(voltage, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL);
> +	writel(emphasis, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> +
> +	return 0;
> +}
> +
>   static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy)
>   {
>   	writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_PSR_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
> @@ -3757,16 +3818,7 @@ static void qcom_qmp_v4_phy_dp_aux_init(struct qmp_phy *qphy)
>   
>   static void qcom_qmp_v4_phy_configure_dp_tx(struct qmp_phy *qphy)
>   {
> -	/* Program default values before writing proper values */
> -	writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL);
> -	writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL);
> -
> -	writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> -	writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> -
> -	qcom_qmp_phy_configure_dp_swing(qphy,
> -			QSERDES_V4_TX_TX_DRV_LVL,
> -			QSERDES_V4_TX_TX_EMP_POST1_LVL);
> +	qcom_qmp_v4_phy_configure_dp_swing(qphy);
>   }
>   
>   static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy)
> @@ -3885,6 +3937,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy)
>   	writel(drvr1_en, qphy->tx2 + QSERDES_V4_TX_HIGHZ_DRVR_EN);
>   	writel(bias1_en, qphy->tx2 + QSERDES_V4_TX_TRANSCEIVER_BIAS_EN);
>   
> +	writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV);
> +	writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV);
> +
>   	writel(0x18, qphy->pcs + QSERDES_DP_PHY_CFG);
>   	udelay(2000);
>   	writel(0x19, qphy->pcs + QSERDES_DP_PHY_CFG);
> @@ -3896,11 +3951,9 @@ static int qcom_qmp_v4_phy_configure_dp_phy(struct qmp_phy *qphy)
>   			10000))
>   		return -ETIMEDOUT;
>   
> -	writel(0x0a, qphy->tx + QSERDES_V4_TX_TX_POL_INV);
> -	writel(0x0a, qphy->tx2 + QSERDES_V4_TX_TX_POL_INV);
>   
> -	writel(0x27, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL);
> -	writel(0x27, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL);
> +	writel(0x22, qphy->tx + QSERDES_V4_TX_TX_DRV_LVL);
> +	writel(0x22, qphy->tx2 + QSERDES_V4_TX_TX_DRV_LVL);
>   
>   	writel(0x20, qphy->tx + QSERDES_V4_TX_TX_EMP_POST1_LVL);
>   	writel(0x20, qphy->tx2 + QSERDES_V4_TX_TX_EMP_POST1_LVL);
> 


-- 
With best wishes
Dmitry

  reply	other threads:[~2021-09-03 19:09 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-08-27 21:10 [PATCH v2] phy: qcom-qmp: add support for display port voltage and pre-emphasis swing Kuogee Hsieh
2021-09-03 19:09 ` Dmitry Baryshkov [this message]
2021-09-03 19:16   ` Stephen Boyd

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=72483937-8ccb-331b-e1af-8f30f6cefc07@linaro.org \
    --to=dmitry.baryshkov@linaro.org \
    --cc=abhinavk@codeaurora.org \
    --cc=agross@kernel.org \
    --cc=aravindh@codeaurora.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=freedreno@lists.freedesktop.org \
    --cc=khsieh@codeaurora.org \
    --cc=kishon@ti.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robdclark@gmail.com \
    --cc=robh+dt@kernel.org \
    --cc=sean@poorly.run \
    --cc=swboyd@chromium.org \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).