Re: [PATCH v4 3/4] soc: amlogic: Add support for Secure power domains controller

[Kevin Hilman <khilman@baylibre.com>]

Hi Jianxin,

Jianxin Pan <jianxin.pan@amlogic.com> writes:

> Add support for the Amlogic Secure Power controller. In A1/C1 series, power
> control registers are in secure domain, and should be accessed by smc.
>
> Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>

This driver is looking pretty good.  A few more minor comments below.

[...]

> +static bool pwrc_secure_is_off(struct meson_secure_pwrc_domain *pwrc_domain)
> +{
> +	int sts = 1;

What does 'sts' mean?  status?  or something else?  Please use a more
descriptive name.

> +	if (meson_sm_call(pwrc_domain->pwrc->fw, SM_PWRC_GET, &sts,
> +			  pwrc_domain->index, 0, 0, 0, 0) < 0)
> +		pr_err("failed to get power domain status\n");

Does any bit in this register mean the power domain is off?  I think it
would be better (and more future proof) if you checked the specific bit
(or mask)

> +	return !!sts;

and then:

    return sts & bitmask;
    
> +}
> +
> +static int meson_secure_pwrc_off(struct generic_pm_domain *domain)
> +{
> +	int sts = 0;

Like above, what does sts mean?

> +	struct meson_secure_pwrc_domain *pwrc_domain =
> +		container_of(domain, struct meson_secure_pwrc_domain, base);
> +
> +	if (meson_sm_call(pwrc_domain->pwrc->fw, SM_PWRC_SET, NULL,
> +			  pwrc_domain->index, PWRC_OFF, 0, 0, 0) < 0) {
> +		pr_err("failed to set power domain off\n");
> +		sts = -EINVAL;
> +	}
> +
> +	return sts;

It looks to me like sts is only used as a return code, so maybe call it
ret for clarity?  or rename it to something more descriptive.

> +}
> +
> +static int meson_secure_pwrc_on(struct generic_pm_domain *domain)
> +{
> +	int sts = 0;
> +	struct meson_secure_pwrc_domain *pwrc_domain =
> +		container_of(domain, struct meson_secure_pwrc_domain, base);
> +
> +	if (meson_sm_call(pwrc_domain->pwrc->fw, SM_PWRC_SET, NULL,
> +			  pwrc_domain->index, PWRC_ON, 0, 0, 0) < 0) {
> +		pr_err("failed to set power domain on\n");
> +		sts = -EINVAL;
> +	}
> +
> +	return sts;

same comment as above.

> +}
> +
> +#define SEC_PD(__name, __flag)			\
> +[PWRC_##__name##_ID] =				\
> +{						\
> +	.name = #__name,			\
> +	.index = PWRC_##__name##_ID,		\
> +	.is_off = pwrc_secure_is_off,	\
> +	.flags = __flag,			\
> +}
> +
> +static struct meson_secure_pwrc_domain_desc a1_pwrc_domains[] = {
> +	SEC_PD(DSPA,	0),
> +	SEC_PD(DSPB,	0),
> +	/* UART should keep working in ATF after suspend and before resume */
> +	SEC_PD(UART,	GENPD_FLAG_ALWAYS_ON),
> +	/* DMC is for DDR PHY ana/dig and DMC, and should be always on */
> +	SEC_PD(DMC,	GENPD_FLAG_ALWAYS_ON),
> +	SEC_PD(I2C,	0),
> +	SEC_PD(PSRAM,	0),
> +	SEC_PD(ACODEC,	0),
> +	SEC_PD(AUDIO,	0),
> +	SEC_PD(OTP,	0),
> +	SEC_PD(DMA,	0),
> +	SEC_PD(SD_EMMC,	0),
> +	SEC_PD(RAMA,	0),
> +	/* SRAMB is used as AFT runtime memory, and should be always on */

AFT?  I assume you mean ATF?

> +	SEC_PD(RAMB,	GENPD_FLAG_ALWAYS_ON),
> +	SEC_PD(IR,	0),
> +	SEC_PD(SPICC,	0),
> +	SEC_PD(SPIFC,	0),
> +	SEC_PD(USB,	0),
> +	/* NIC is for NIC400, and should be always on */

Why?

> +	SEC_PD(NIC,	GENPD_FLAG_ALWAYS_ON),
> +	SEC_PD(PDMIN,	0),
> +	SEC_PD(RSA,	0),
> +};

[...]

Kevin