From: Stefan Agner <stefan@agner.ch>
To: Anthony Felice <tony.felice@timesys.com>
Cc: dri-devel@lists.freedesktop.org, shawnguo@kernel.org,
dmitry.torokhov@gmail.com, robh+dt@kernel.org,
mark.rutland@arm.com, kernel@pengutronix.de,
linux@armlinux.org.uk, fabio.estevam@nxp.com,
geert@linux-m68k.org, mwelling@ieee.org, sre@kernel.org,
damien.riegel@savoirfairelinux.com, maitysanchayan@gmail.com,
linux-input@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 1/4] ARM: dts: vf610-twr: Enable display controller
Date: Sat, 25 Jun 2016 13:53:32 -0700 [thread overview]
Message-ID: <80c8e7b31ed47dbc419937a281b4b7c5@agner.ch> (raw)
In-Reply-To: <1466797486-31558-2-git-send-email-tony.felice@timesys.com>
On 2016-06-24 12:44, Anthony Felice wrote:
> This adds nodes to enable tcon0 and dcu0 for the Vybrid Tower. These
> are used to drive the Vybrid Tower TWR-LCD-RGB display. Also, a node
> for the nec nl4827hc19-05b panel on the TWR-LCD-RGB display has been
> added.
So my pixel clock polarity changes which will be part of 4.7 work for
Tower? I could never actually test that since I don't have the display
here...
https://patchwork.kernel.org/patch/8874971/
This patch looks good to me:
Acked-by: Stefan Agner <stefan@agner.ch>
--
Stefan
>
> Signed-off-by: Anthony Felice <tony.felice@timesys.com>
> ---
> arch/arm/boot/dts/vf610-twr.dts | 48 +++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 48 insertions(+)
>
> diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts
> index cdc1007..ad1aff9 100644
> --- a/arch/arm/boot/dts/vf610-twr.dts
> +++ b/arch/arm/boot/dts/vf610-twr.dts
> @@ -66,6 +66,10 @@
> clock-frequency = <50000000>;
> };
>
> + panel: panel {
> + compatible = "nec,nl4827hc19-05b";
> + };
> +
> regulators {
> compatible = "simple-bus";
> #address-cells = <1>;
> @@ -134,6 +138,13 @@
> <&clks VF610_CLK_ENET_EXT>;
> };
>
> +&dcu0 {
> + fsl,panel = <&panel>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_dcu0>;
> + status = "okay";
> +};
> +
> &dspi0 {
> bus-num = <0>;
> pinctrl-names = "default";
> @@ -210,6 +221,39 @@
>
> &iomuxc {
> vf610-twr {
> + pinctrl_dcu0: dcu0grp {
> + fsl,pins = <
> + VF610_PAD_PTE0__DCU0_HSYNC 0x42
> + VF610_PAD_PTE1__DCU0_VSYNC 0x42
> + VF610_PAD_PTE2__DCU0_PCLK 0x42
> + VF610_PAD_PTE4__DCU0_DE 0x42
> + VF610_PAD_PTE5__DCU0_R0 0x42
> + VF610_PAD_PTE6__DCU0_R1 0x42
> + VF610_PAD_PTE7__DCU0_R2 0x42
> + VF610_PAD_PTE8__DCU0_R3 0x42
> + VF610_PAD_PTE9__DCU0_R4 0x42
> + VF610_PAD_PTE10__DCU0_R5 0x42
> + VF610_PAD_PTE11__DCU0_R6 0x42
> + VF610_PAD_PTE12__DCU0_R7 0x42
> + VF610_PAD_PTE13__DCU0_G0 0x42
> + VF610_PAD_PTE14__DCU0_G1 0x42
> + VF610_PAD_PTE15__DCU0_G2 0x42
> + VF610_PAD_PTE16__DCU0_G3 0x42
> + VF610_PAD_PTE17__DCU0_G4 0x42
> + VF610_PAD_PTE18__DCU0_G5 0x42
> + VF610_PAD_PTE19__DCU0_G6 0x42
> + VF610_PAD_PTE20__DCU0_G7 0x42
> + VF610_PAD_PTE21__DCU0_B0 0x42
> + VF610_PAD_PTE22__DCU0_B1 0x42
> + VF610_PAD_PTE23__DCU0_B2 0x42
> + VF610_PAD_PTE24__DCU0_B3 0x42
> + VF610_PAD_PTE25__DCU0_B4 0x42
> + VF610_PAD_PTE26__DCU0_B5 0x42
> + VF610_PAD_PTE27__DCU0_B6 0x42
> + VF610_PAD_PTE28__DCU0_B7 0x42
> + >;
> + };
> +
> pinctrl_adc0_ad5: adc0ad5grp {
> fsl,pins = <
> VF610_PAD_PTC30__ADC0_SE5 0xa1
> @@ -370,6 +414,10 @@
> status = "okay";
> };
>
> +&tcon0 {
> + status = "okay";
> +};
> +
> &uart1 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_uart1>;
next prev parent reply other threads:[~2016-06-25 20:57 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-06-24 19:44 [PATCH 0/4] Enable display and touchscreen for Vybrid Tower Anthony Felice
2016-06-24 19:44 ` [PATCH 1/4] ARM: dts: vf610-twr: Enable display controller Anthony Felice
2016-06-25 20:53 ` Stefan Agner [this message]
2016-06-24 19:44 ` [PATCH 2/4] input: touchscreen: crtouch_ts: Add driver Anthony Felice
2016-06-24 22:04 ` Dmitry Torokhov
2016-06-25 20:40 ` Stefan Agner
2016-06-28 20:55 ` Rob Herring
2016-06-24 19:44 ` [PATCH 3/4] ARM: dts: vf610-twr: Add crtouch node and pinmux Anthony Felice
2016-06-24 19:44 ` [PATCH 4/4] ARM: imx_v6_v7_defconfig: enable useful configurations for Vybrid Anthony Felice
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=80c8e7b31ed47dbc419937a281b4b7c5@agner.ch \
--to=stefan@agner.ch \
--cc=damien.riegel@savoirfairelinux.com \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.torokhov@gmail.com \
--cc=dri-devel@lists.freedesktop.org \
--cc=fabio.estevam@nxp.com \
--cc=geert@linux-m68k.org \
--cc=kernel@pengutronix.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=maitysanchayan@gmail.com \
--cc=mark.rutland@arm.com \
--cc=mwelling@ieee.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=sre@kernel.org \
--cc=tony.felice@timesys.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).