From: Rajendra Nayak <rnayak@codeaurora.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: viresh.kumar@linaro.org, sboyd@kernel.org, andy.gross@linaro.org,
ulf.hansson@linaro.org, collinsd@codeaurora.org,
devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v3 5/7] dt-bindings: power: Add qcom rpmh power domain driver bindings
Date: Tue, 12 Jun 2018 12:10:49 +0530 [thread overview]
Message-ID: <8aae8809-77e0-9aa7-0c90-1e6d956ab81e@codeaurora.org> (raw)
In-Reply-To: <20180612053953.GA18050@builder>
On 06/12/2018 11:09 AM, Bjorn Andersson wrote:
> On Mon 11 Jun 21:40 PDT 2018, Rajendra Nayak wrote:
>
>> Add DT bindings to describe the rpmh powerdomains found on Qualcomm
>> Technologies, Inc. SoCs. These power domains communicate a performance
>> state to RPMh, which then translates it into corresponding voltage on
>> a PMIC rail.
>>
>> Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
>> ---
>> .../devicetree/bindings/power/qcom,rpmhpd.txt | 65 +++++++++++++++++++
>> 1 file changed, 65 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/power/qcom,rpmhpd.txt
>>
>> diff --git a/Documentation/devicetree/bindings/power/qcom,rpmhpd.txt b/Documentation/devicetree/bindings/power/qcom,rpmhpd.txt
>> new file mode 100644
>> index 000000000000..41ef7afa6b24
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/power/qcom,rpmhpd.txt
>> @@ -0,0 +1,65 @@
>> +Qualcomm RPMh Power domains
>> +
>> +For RPMh Power domains, we communicate a performance state to RPMh
>> +which then translates it into a corresponding voltage on a rail
>> +
>> +Required Properties:
>> + - compatible: Should be one of the following
>> + * qcom,sdm845-rpmhpd: RPMh Power domain for the sdm845 family of SoC
>
> Afaict this binding is identical to the one introduced in patch 1, so I
> would suggest that you just add the compatible there.
Sure, makes sense. thanks.
>
> Regards,
> Bjorn
>
>> + - power-domain-cells: number of cells in power domain specifier
>> + must be 1
>> + - operating-points-v2: Phandle to the OPP table for the power-domain.
>> + Refer to Documentation/devicetree/bindings/power/power_domain.txt
>> + and Documentation/devicetree/bindings/opp/qcom-opp.txt for more details
>> +
>> +Example:
>> +
>> + rpmhpd: power-controller {
>> + compatible = "qcom,sdm845-rpmhpd";
>> + #power-domain-cells = <1>;
>> + operating-points-v2 = <&rpmhpd_opp_table>;
>> + };
>> +
>> + rpmhpd_opp_table: opp-table {
>> + compatible = "operating-points-v2-qcom-level";
>> +
>> + rpmhpd_opp_ret: opp1 {
>> + qcom-level = <16>;
>> + };
>> +
>> + rpmhpd_opp_min_svs: opp2 {
>> + qcom-level = <48>;
>> + };
>> +
>> + rpmhpd_opp_low_svs: opp3 {
>> + qcom-level = <64>;
>> + };
>> +
>> + rpmhpd_opp_svs: opp4 {
>> + qcom-level = <128>;
>> + };
>> +
>> + rpmhpd_opp_svs_l1: opp5 {
>> + qcom-level = <192>;
>> + };
>> +
>> + rpmhpd_opp_nom: opp6 {
>> + qcom-level = <256>;
>> + };
>> +
>> + rpmhpd_opp_nom_l1: opp7 {
>> + qcom-level = <320>;
>> + };
>> +
>> + rpmhpd_opp_nom_l2: opp8 {
>> + qcom-level = <336>;
>> + };
>> +
>> + rpmhpd_opp_turbo: opp9 {
>> + qcom-level = <384>;
>> + };
>> +
>> + rpmhpd_opp_turbo_l1: opp10 {
>> + qcom-level = <416>;
>> + };
>> + };
>> --
>> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
>> of Code Aurora Forum, hosted by The Linux Foundation
>>
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
hosted by The Linux Foundation
next prev parent reply other threads:[~2018-06-12 6:40 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-12 4:40 [PATCH v3 0/7] Add powerdomain driver for corners on msm8996/sdm845 Rajendra Nayak
2018-06-12 4:40 ` [PATCH v3 1/7] dt-bindings: power: Add qcom rpm power domain driver bindings Rajendra Nayak
2018-06-12 4:40 ` [PATCH v3 2/7] soc: qcom: rpmpd: Add a Power domain driver to model corners Rajendra Nayak
2018-06-12 7:39 ` Ulf Hansson
2018-06-25 17:15 ` Rob Herring
2018-06-12 4:40 ` [PATCH v3 3/7] soc: qcom: rpmpd: Add support for get/set performance state Rajendra Nayak
2018-06-12 4:40 ` [PATCH v3 4/7] arm64: dts: msm8996: Add rpmpd device node Rajendra Nayak
2018-06-12 4:40 ` [PATCH v3 5/7] dt-bindings: power: Add qcom rpmh power domain driver bindings Rajendra Nayak
2018-06-12 5:39 ` Bjorn Andersson
2018-06-12 6:40 ` Rajendra Nayak [this message]
2018-06-13 22:12 ` David Collins
2018-06-14 6:26 ` Rajendra Nayak
2018-06-19 9:59 ` Viresh Kumar
2018-06-12 4:40 ` [PATCH v3 6/7] soc: qcom: Add RPMh Power domain driver Rajendra Nayak
2018-06-12 7:46 ` Ulf Hansson
2018-06-12 19:06 ` Rob Herring
2018-06-13 3:25 ` Rajendra Nayak
2018-06-12 19:42 ` Matthias Kaehlcke
2018-06-13 3:30 ` Rajendra Nayak
2018-06-14 0:32 ` David Collins
2018-06-14 6:54 ` Rajendra Nayak
2018-06-14 18:17 ` David Collins
2018-06-15 9:25 ` Ulf Hansson
2018-06-15 21:46 ` David Collins
2018-06-16 12:13 ` Ulf Hansson
2018-06-12 4:40 ` [PATCH v3 7/7] soc: qcom: rpmpd/rpmhpd: Add a max vote on all corners at init Rajendra Nayak
2018-06-13 22:28 ` David Collins
2018-06-14 6:35 ` Rajendra Nayak
2018-06-19 10:10 ` Viresh Kumar
2018-06-25 8:57 ` Ulf Hansson
2018-06-25 10:10 ` Rajendra Nayak
2018-06-12 7:47 ` [PATCH v3 0/7] Add powerdomain driver for corners on msm8996/sdm845 Ulf Hansson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=8aae8809-77e0-9aa7-0c90-1e6d956ab81e@codeaurora.org \
--to=rnayak@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=collinsd@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=sboyd@kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).