RE: [PATCH v4 0/8] mtd: spi-nor: parse SFDP tables to setup (Q)SPI memories

["Krzeminski, Marcin (Nokia - PL/Wroclaw)" <marcin.krzeminski@nokia.com>]

> -----Original Message-----
> From: linux-mtd [mailto:linux-mtd-bounces@lists.infradead.org] On Behalf
> Of Cyrille Pitchen
> Sent: Monday, November 21, 2016 3:16 PM
> To: computersforpeace@gmail.com; marek.vasut@gmail.com;
> boris.brezillon@free-electrons.com; richard@nod.at; linux-
> mtd@lists.infradead.org
> Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>; nicolas.ferre@atmel.com;
> linux-kernel@vger.kernel.org
> Subject: [PATCH v4 0/8] mtd: spi-nor: parse SFDP tables to setup (Q)SPI
> memories
> 
> Hi all,
> 
> This series extends support of SPI protocols to new protocols such as SPI x-2-
> 2 and SPI x-4-4. Also spi_nor_scan() tries now to select the right op codes,
> timing parameters (number of mode and dummy cycles) and erase sector
> size by parsing the Serial Flash Discoverable Parameter (SFDP) tables, when
> available, as defined in the JEDEC JESD216 specifications.
> 
> When SFDP tables are not available, legacy settings are still used for
> backward compatibility (SPI and earlier QSPI memories).
> 
> Support of SPI memories >128Mbits is also improved by using the 4byte
> address instruction set, when available. Using those dedicated op codes is
> stateless as opposed to enter the 4byte address mode, hence a better
> compatibility with some boot loaders which expect to use 3byte address op
> codes.
> 
> 
> This series was tested on a Atmel sama5d2 xplained board with the atmel-
> qspi.c driver. Except for SST memories, the SPI bus clock was set to 83MHz.
> The config MTD_SPI_NOR_USE_4K_SECTORS was selected.
> 
> For my tests, I used some shell scripts using mtd_debug and sha1sum to
> check the data integrity.
> 
> e.g:
> #!/bin/sh
> 
> mtd_debug erase /dev/mtd5 0 0x780000
> mtd_debug write /dev/mtd5 0 7674703 sama5d4_doc11238.pdf mtd_debug
> read /dev/mtd5 0 7674703 sama5d4_tmp.pdf
> 
> sha1sum sama5d4_doc11238.pdf sama5d4_tmp.pdf
> 
> 
> Depending on the actual memory size, I may have used other partitions
> (/dev/mtd4) and input file size (2880044 and 320044 bytes).
> 
> 
> The series was tested with the following QSPI memories:
> 
> Spansion/Cypress:
> - s25fl127s	OK
> - s25fl512s	OK
> - s25fl164k	OK
> 
> Micron:
> - n25q128a	OK
> - n25q512	OK
> - n25q01g	OK
> 
> Macronix:
> - mx25v1635f	OK
> - mx25l3235f	OK
> - mx25l3273f	OK
> - mx25l6433f	OK
> - mx25l6473f	OK
> - mx25l12835f	OK
> - mx25l12845g	OK
> - mx25l12873g	OK
> - mx25l25645g	OK
> - mx25l25673g	OK
> - mx25l51245g	OK
> - mx66l1g45g	OK
> 
> SST:
> - sst26vf016b	OK
> - sst26vf032b	OK
> - sst26vf064b	OK
> 
> 
> Best regards,
> 
> Cyrille
> 
Hello,

I have tested this series on:
mx66u51235f OK
mt25qu01g OK(1)
s25fs512s FAILED(2)

(1) - There is a problem with Die Erase command. There is no 4byte version. I workarounded it by enabling 4byte mode before send, and disabled just after.
Resigning from Die Erase is bad idea because of erase speed. Having stateless mode is also bad, so some better idea that my workaround could be nice.
(2) - Totally failed because this chip does not support 64KiB sectors, but still reports that command for erasing that kind of sector is available,
moreover it is the same as command for erasing 256KiB sector. Solution for this, and for other flash could be that preferred sector size
is a parameter for spi-nor framework.

My tests covers my use case of mtd/spi-nor framework (ubi, ubifs and jffs2 + some regression).
	
Some small comments in patches.

Thanks,
Marcin

> ChangeLog:
> 
> v3 -> v4
> - replace dev_info() by dev_dbg() in patch 1.
> - split former patch 2 into 2 patches:
>   + new patch 2 deals with the rename of SPINOR_OP_READ4_* macros
>   + new patch 3 deals with the alternative methode to support memory
> >16MiB
> - add comment in patch 3 to describe the dichotomic search performed by
>   spi_nor_convert_opcode().
> - change return type from int to void for m25p80_proto2nbits() in patch 6.
> - remove former patches 8 & 9 from the v2 series: the support of the
>   Macronix mx66l1g45g memory will be sent in a separated patch.
> 
> v2 -> v3
> - tested with new samples: Micron n25q512, n25q01g and Macronix
>   mx25v1635f, mx25l3235f, mx25l3273f.
> - add "Reviewed-by: Jagan Teki <jagan@openedev.com>" on patch 1.
> - add "Tested-by: Vignesh R <vigneshr@ti.com>" on patch 2.
> - fix some checkpatch warnings.
> - add call of spi_nor_wait_till_ready() in spansion_new_quad_enable()
>   and sr2_bit7_quad_enable(), as suggested by Joel Esponde on patch 6.
> - test JESD216 rev A (minor 5) instead of rev B (minor 6) with the return
>   code of spi_nor_parse_sfdp() from spi_nor_init_params() on patch 6.
>   The seven additional DWORDs of the Basic Flash Parameter Table were
>   introduced in rev A, not rev B, so the 15th DWORD was already available
>   in rev A. The 15th DWORD provides us with the Quad Enable Requirements
>   (QER) bits.
>   Basic Flash Parameter Table size:
>   + JESD216 :  9 DWORDS
>   + JESD216A: 16 DWORDS
>   + JESD216B: 16 DWORDS
> 
> v1 -> v2
> - fix patch 3 to resolve compiler errors on hisi-sfc.c and cadence-quadspi.c
>   drivers
> 
> 
> Cyrille Pitchen (8):
>   mtd: spi-nor: improve macronix_quad_enable()
>   mtd: spi-nor: rename SPINOR_OP_* macros of the 4-byte address op codes
>   mtd: spi-nor: add an alternative method to support memory >16MiB
>   mtd: spi-nor: add support of SPI protocols like SPI 1-2-2 and SPI
>     1-4-4
>   mtd: spi-nor: remove unused set_quad_mode() function
>   mtd: m25p80: add support of dual and quad spi protocols to all
>     commands
>   mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables
>   mtd: spi-nor: parse SFDP 4-byte Address Instruction Table
> 
>  drivers/mtd/devices/m25p80.c            |  191 ++++--
>  drivers/mtd/devices/serial_flash_cmds.h |    7 -
>  drivers/mtd/devices/st_spi_fsm.c        |   28 +-
>  drivers/mtd/spi-nor/atmel-quadspi.c     |   83 ++-
>  drivers/mtd/spi-nor/cadence-quadspi.c   |   18 +-
>  drivers/mtd/spi-nor/fsl-quadspi.c       |    8 +-
>  drivers/mtd/spi-nor/hisi-sfc.c          |   32 +-
>  drivers/mtd/spi-nor/mtk-quadspi.c       |   16 +-
>  drivers/mtd/spi-nor/nxp-spifi.c         |   21 +-
>  drivers/mtd/spi-nor/spi-nor.c           | 1017
> ++++++++++++++++++++++++++++---
>  drivers/spi/spi-bcm-qspi.c              |    6 +-
>  include/linux/mtd/spi-nor.h             |  164 ++++-
>  12 files changed, 1351 insertions(+), 240 deletions(-)
> 
> --
> 2.7.4
> 
> 
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/