From: Naresh Kamboju <naresh.kamboju@linaro.org>
To: LTP List <ltp@lists.linux.it>,
open list <linux-kernel@vger.kernel.org>,
linux-block <linux-block@vger.kernel.org>
Cc: chrubis <chrubis@suse.cz>, Arnd Bergmann <arnd@arndb.de>,
maco@android.com, Christoph Hellwig <hch@lst.de>,
Jens Axboe <axboe@kernel.dk>, Jan Stancek <jstancek@redhat.com>,
Yang Xu <xuyang2018.jy@cn.fujitsu.com>,
Xiao Yang <yangx.jy@cn.fujitsu.com>,
Richard Palethorpe <rpalethorpe@suse.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
lkft-triage@lists.linaro.org
Subject: Re: LTP: syscalls: regression on mainline - ioctl_loop01 mknod07 setns01
Date: Thu, 4 Jun 2020 22:49:24 +0530 [thread overview]
Message-ID: <CA+G9fYuUvjDeLXVm2ax_5UF=OJeH7fog0U7GG2vEUXg-HXWRqg@mail.gmail.com> (raw)
In-Reply-To: <CA+G9fYuGwcE3zyMFQPpfA0CyW=4WOg9V=kCfKhS7b8930jQofA@mail.gmail.com>
+ linux-block@vger.kernel.org
On Thu, 4 Jun 2020 at 22:47, Naresh Kamboju <naresh.kamboju@linaro.org> wrote:
>
> Following three test cases reported as regression on Linux mainline kernel
> on x86_64, arm64, arm and i386
>
> ltp-syscalls-tests:
> * ioctl_loop01
> * mknod07
> * setns01
>
> git repo: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
> git branch: master
> GOOD:
> git commit: b23c4771ff62de8ca9b5e4a2d64491b2fb6f8f69
> git describe: v5.7-1230-gb23c4771ff62
> BAD:
> git commit: 1ee08de1e234d95b5b4f866878b72fceb5372904
> git describe: v5.7-3523-g1ee08de1e234
>
> kernel-config: https://builds.tuxbuild.com/U3bU0dMA62OVHb4DvZIVuw/kernel.config
>
> We are investigating these failures.
>
> tst_test.c:906: CONF: btrfs driver not available
> tst_test.c:1246: INFO: Timeout per run is 0h 15m 00s
> tst_device.c:88: INFO: Found free device 1 '/dev/loop1'
> ioctl_loop01.c:49: PASS: /sys/block/loop1/loop/partscan = 0
> [ 1073.639677] loop_set_status: loop1 () has still dirty pages (nrpages=1)
> ioctl_loop01.c:50: PASS: /sys/block/loop1/loop/autoclear = 0
> ioctl_loop01.c:51: PASS: /sys/block/loop1/loop/backing_file =
> '/scratch/ltp-mnIdulzriQ/9cPtLQ/test.img'
> ioctl_loop01.c:63: FAIL: expect 12 but got 17
> ioctl_loop01.c:67: FAIL: /sys/block/loop1/loop/partscan != 1 got 0
> ioctl_loop01.c:68: FAIL: /sys/block/loop1/loop/autoclear != 1 got 0
> ioctl_loop01.c:79: FAIL: access /dev/loop1p1 fails
> [ 1073.679678] loop_set_status: loop1 () has still dirty pages (nrpages=1)
> ioctl_loop01.c:85: FAIL: access /sys/block/loop1/loop1p1 fails
>
> HINT: You _MAY_ be missing kernel fixes, see:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=10c70d95c0f2
>
> mke2fs 1.43.8 (1-Jan-2018)
> [ 1264.711379] EXT4-fs (loop0): mounting ext2 file system using the
> ext4 subsystem
> [ 1264.716642] EXT4-fs (loop0): mounted filesystem without journal. Opts: (null)
> mknod07 0 TINFO : Using test device LTP_DEV='/dev/loop0'
> mknod07 0 TINFO : Formatting /dev/loop0 with ext2 opts='' extra opts=''
> mknod07 1 TPASS : mknod failed as expected:
> TEST_ERRNO=EACCES(13): Permission denied
> mknod07 2 TPASS : mknod failed as expected:
> TEST_ERRNO=EACCES(13): Permission denied
> mknod07 3 TFAIL : mknod07.c:155: mknod succeeded unexpectedly
> mknod07 4 TPASS : mknod failed as expected:
> TEST_ERRNO=EPERM(1): Operation not permitted
> mknod07 5 TPASS : mknod failed as expected:
> TEST_ERRNO=EROFS(30): Read-only file system
> mknod07 6 TPASS : mknod failed as expected:
> TEST_ERRNO=ELOOP(40): Too many levels of symbolic links
>
>
> setns01 0 TINFO : ns_name=ipc, ns_fds[0]=6, ns_types[0]=0x8000000
> setns01 0 TINFO : ns_name=mnt, ns_fds[1]=7, ns_types[1]=0x20000
> setns01 0 TINFO : ns_name=net, ns_fds[2]=8, ns_types[2]=0x40000000
> setns01 0 TINFO : ns_name=pid, ns_fds[3]=9, ns_types[3]=0x20000000
> setns01 0 TINFO : ns_name=uts, ns_fds[4]=10, ns_types[4]=0x4000000
> setns01 0 TINFO : setns(-1, 0x8000000)
> setns01 1 TPASS : invalid fd exp_errno=9
> setns01 0 TINFO : setns(-1, 0x20000)
> setns01 2 TPASS : invalid fd exp_errno=9
> setns01 0 TINFO : setns(-1, 0x40000000)
> setns01 3 TPASS : invalid fd exp_errno=9
> setns01 0 TINFO : setns(-1, 0x20000000)
> setns01 4 TPASS : invalid fd exp_errno=9
> setns01 0 TINFO : setns(-1, 0x4000000)
> setns01 5 TPASS : invalid fd exp_errno=9
> setns01 0 TINFO : setns(11, 0x8000000)
> setns01 6 TFAIL : setns01.c:176: regular file fd exp_errno=22:
> errno=EBADF(9): Bad file descriptor
> setns01 0 TINFO : setns(11, 0x20000)
> setns01 7 TFAIL : setns01.c:176: regular file fd exp_errno=22:
> errno=EBADF(9): Bad file descriptor
> setns01 0 TINFO : setns(11, 0x40000000)
> setns01 8 TFAIL : setns01.c:176: regular file fd exp_errno=22:
> errno=EBADF(9): Bad file descriptor
> setns01 0 TINFO : setns(11, 0x20000000)
> setns01 9 TFAIL : setns01.c:176: regular file fd exp_errno=22:
> errno=EBADF(9): Bad file descriptor
> setns01 0 TINFO : setns(11, 0x4000000)
> setns01 10 TFAIL : setns01.c:176: regular file fd exp_errno=22:
> errno=EBADF(9): Bad file descriptor
>
> Full test log link,
> https://lkft.validation.linaro.org/scheduler/job/1467931#L8047
>
> test results comparison shows this test case started failing from June-2-2020
> https://qa-reports.linaro.org/lkft/linux-mainline-oe/build/v5.7-4092-g38696e33e2bd/testrun/2779586/suite/ltp-syscalls-tests/test/ioctl_loop01/history/
>
> https://qa-reports.linaro.org/lkft/linux-mainline-oe/build/v5.7-4092-g38696e33e2bd/testrun/2779586/suite/ltp-syscalls-tests/test/setns01/history/
>
> https://qa-reports.linaro.org/lkft/linux-mainline-oe/build/v5.7-4092-g38696e33e2bd/testrun/2779586/suite/ltp-syscalls-tests/test/mknod07/history/
>
>
> --
> Linaro LKFT
> https://lkft.linaro.org
next prev parent reply other threads:[~2020-06-04 17:19 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-04 17:17 LTP: syscalls: regression on mainline - ioctl_loop01 mknod07 setns01 Naresh Kamboju
2020-06-04 17:19 ` Naresh Kamboju [this message]
2020-06-04 19:10 ` Martijn Coenen
2020-06-04 20:27 ` Martijn Coenen
2020-06-05 8:21 ` Yang Xu
2020-06-05 8:59 ` [LTP] " Yang Xu
2020-06-05 9:11 ` Martijn Coenen
2020-06-05 9:27 ` Yang Xu
2020-06-05 11:31 ` Martijn Coenen
2020-06-05 8:27 ` Jan Stancek
2020-06-05 10:50 ` Naresh Kamboju
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CA+G9fYuUvjDeLXVm2ax_5UF=OJeH7fog0U7GG2vEUXg-HXWRqg@mail.gmail.com' \
--to=naresh.kamboju@linaro.org \
--cc=arnd@arndb.de \
--cc=axboe@kernel.dk \
--cc=chrubis@suse.cz \
--cc=hch@lst.de \
--cc=jstancek@redhat.com \
--cc=linux-block@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=lkft-triage@lists.linaro.org \
--cc=ltp@lists.linux.it \
--cc=maco@android.com \
--cc=rpalethorpe@suse.com \
--cc=viresh.kumar@linaro.org \
--cc=xuyang2018.jy@cn.fujitsu.com \
--cc=yangx.jy@cn.fujitsu.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).