From: Benjamin Gaignard <benjamin.gaignard@linaro.org>
To: Rob Herring <robh@kernel.org>
Cc: Lee Jones <lee.jones@linaro.org>,
Mark Rutland <mark.rutland@arm.com>,
alexandre.torgue@st.com, devicetree@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Thierry Reding <thierry.reding@gmail.com>,
linux-pwm@vger.kernel.org, Jonathan Cameron <jic23@kernel.org>,
knaack.h@gmx.de, Lars-Peter Clausen <lars@metafoo.de>,
Peter Meerwald-Stadler <pmeerw@pmeerw.net>,
linux-iio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
Fabrice Gasnier <fabrice.gasnier@st.com>,
Gerald Baeza <gerald.baeza@st.com>,
Arnaud Pouliquen <arnaud.pouliquen@st.com>,
Linus Walleij <linus.walleij@linaro.org>,
Linaro Kernel Mailman List <linaro-kernel@lists.linaro.org>,
Benjamin Gaignard <benjamin.gaignard@st.com>
Subject: Re: [PATCH v6 7/8] ARM: dts: stm32: add Timers driver for stm32f429 MCU
Date: Tue, 13 Dec 2016 10:15:21 +0100 [thread overview]
Message-ID: <CA+M3ks6hMDVqDkjn_vcu-d2YkJkiAmCS44Nc7rtfgAkD09LNFA@mail.gmail.com> (raw)
In-Reply-To: <20161212185943.ph7njaqb2lxtgdn4@rob-hp-laptop>
2016-12-12 19:59 GMT+01:00 Rob Herring <robh@kernel.org>:
> On Fri, Dec 09, 2016 at 03:15:18PM +0100, Benjamin Gaignard wrote:
>> Add Timers and it sub-nodes into DT for stm32f429 family.
>>
>> version 6:
>> - split patch in two: one for SoC family and one for stm32f469
>> discovery board.
>>
>> version 5:
>> - rename gptimer node to timers
>> - re-order timers node par addresses
>>
>> version 4:
>> - remove unwanted indexing in pwm@ and timer@ node name
>> - use "reg" instead of additional parameters to set timer
>> configuration
>>
>> version 3:
>> - use "st,stm32-timer-trigger" in DT
>>
>> version 2:
>> - use parameters to describe hardware capabilities
>> - do not use references for pwm and iio timer subnodes
>>
>> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
>> ---
>> arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++
>> 1 file changed, 275 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
>> index bca491d..d0fb9cc 100644
>> --- a/arch/arm/boot/dts/stm32f429.dtsi
>> +++ b/arch/arm/boot/dts/stm32f429.dtsi
>> @@ -355,6 +355,21 @@
>> slew-rate = <2>;
>> };
>> };
>> +
>> + pwm1_pins: pwm@1 {
>
> No reg prop, so should not have a unit-address. Given the names in the
> define below, seems like "timer1" would be appropriate.
>
>> + pins {
>> + pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>,
>> + <STM32F429_PB13_FUNC_TIM1_CH1N>,
>> + <STM32F429_PB12_FUNC_TIM1_BKIN>;
>> + };
>> + };
>> +
>> + pwm3_pins: pwm@3 {
>> + pins {
>> + pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>,
>> + <STM32F429_PB5_FUNC_TIM3_CH2>;
>> + };
>> + };
>> };
>>
>> rcc: rcc@40023810 {
>> @@ -426,6 +441,266 @@
>> interrupts = <80>;
>> clocks = <&rcc 0 38>;
>> };
>> +
>> + timers2: timers@40000000 {
>
> timer@...
>
> It may be more than just a timer, there's not a better generic name.
>
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40000000 0x400>;
>> + clocks = <&rcc 0 128>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <1>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers3: timers@40000400 {
>
> ditto
>
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40000400 0x400>;
>> + clocks = <&rcc 0 129>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <2>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers4: timers@40000800 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40000800 0x400>;
>> + clocks = <&rcc 0 130>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <3>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers5: timers@40000C00 {
>
> timer@...
>
> And use lowercase hex.
>
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40000C00 0x400>;
>
> ditto
>
>> + clocks = <&rcc 0 131>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <4>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers6: timers@40001000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40001000 0x400>;
>> + clocks = <&rcc 0 132>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <5>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers7: timers@40001400 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40001400 0x400>;
>> + clocks = <&rcc 0 133>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <6>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers12: timers@40001800 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40001800 0x400>;
>> + clocks = <&rcc 0 134>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <9>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers13: timers@40001C00 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40001C00 0x400>;
>> + clocks = <&rcc 0 135>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers14: timers@40002000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40002000 0x400>;
>> + clocks = <&rcc 0 136>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers1: timers@40010000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40010000 0x400>;
>> + clocks = <&rcc 0 160>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <0>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers8: timers@40010400 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40010400 0x400>;
>> + clocks = <&rcc 0 161>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <7>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers9: timers@40014000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40014000 0x400>;
>> + clocks = <&rcc 0 176>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> +
>> + timer {
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <8>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers10: timers@40014400 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40014400 0x400>;
>> + clocks = <&rcc 0 177>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> + };
>> +
>> + timers11: timers@40014800 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40014800 0x400>;
>> + clocks = <&rcc 0 178>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm {
>> + compatible = "st,stm32-pwm";
>> + status = "disabled";
>> + };
>> + };
>> };
>> };
>>
>> --
>> 1.9.1
>>
--
Benjamin Gaignard
Graphic Study Group
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2016-12-13 9:15 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-12-09 14:15 [PATCH v6 0/8] Add PWM and IIO timer drivers for STM32 Benjamin Gaignard
2016-12-09 14:15 ` [PATCH v6 1/8] MFD: add bindings for STM32 Timers driver Benjamin Gaignard
2016-12-12 7:46 ` Lee Jones
2016-12-12 18:51 ` Rob Herring
2016-12-13 9:29 ` Benjamin Gaignard
2016-12-13 21:07 ` Rob Herring
2016-12-14 13:07 ` Benjamin Gaignard
2016-12-09 14:15 ` [PATCH v6 2/8] MFD: add " Benjamin Gaignard
2016-12-12 7:47 ` Lee Jones
2016-12-30 20:38 ` Jonathan Cameron
2016-12-09 14:15 ` [PATCH v6 3/8] PWM: add pwm-stm32 DT bindings Benjamin Gaignard
2016-12-12 19:02 ` Rob Herring
2016-12-13 11:11 ` Lee Jones
2016-12-13 15:57 ` Rob Herring
2016-12-13 16:28 ` Benjamin Gaignard
2016-12-13 17:11 ` Rob Herring
2016-12-19 12:55 ` Lee Jones
2016-12-09 14:15 ` [PATCH v6 4/8] PWM: add PWM driver for STM32 plaftorm Benjamin Gaignard
2016-12-09 14:15 ` [PATCH v6 5/8] IIO: add bindings for STM32 timer trigger driver Benjamin Gaignard
2016-12-12 19:28 ` Rob Herring
2016-12-09 14:15 ` [PATCH v6 6/8] IIO: add " Benjamin Gaignard
2016-12-30 21:12 ` Jonathan Cameron
2017-01-02 8:46 ` Benjamin Gaignard
2017-01-02 18:22 ` Jonathan Cameron
2017-01-03 9:23 ` Benjamin Gaignard
2017-01-03 12:59 ` Benjamin Gaignard
2017-01-03 17:24 ` Jonathan Cameron
2017-01-03 17:16 ` Jonathan Cameron
2016-12-09 14:15 ` [PATCH v6 7/8] ARM: dts: stm32: add Timers driver for stm32f429 MCU Benjamin Gaignard
2016-12-12 18:59 ` Rob Herring
2016-12-13 9:15 ` Benjamin Gaignard [this message]
2016-12-13 9:29 ` Benjamin Gaignard
2016-12-09 14:15 ` [PATCH v6 8/8] ARM: dts: stm32: Enable pw1 and pwm3 for stm32f469-disco Benjamin Gaignard
2016-12-12 7:48 ` [PATCH v6 0/8] Add PWM and IIO timer drivers for STM32 Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CA+M3ks6hMDVqDkjn_vcu-d2YkJkiAmCS44Nc7rtfgAkD09LNFA@mail.gmail.com \
--to=benjamin.gaignard@linaro.org \
--cc=alexandre.torgue@st.com \
--cc=arnaud.pouliquen@st.com \
--cc=benjamin.gaignard@st.com \
--cc=devicetree@vger.kernel.org \
--cc=fabrice.gasnier@st.com \
--cc=gerald.baeza@st.com \
--cc=jic23@kernel.org \
--cc=knaack.h@gmx.de \
--cc=lars@metafoo.de \
--cc=lee.jones@linaro.org \
--cc=linaro-kernel@lists.linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pwm@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pmeerw@pmeerw.net \
--cc=robh@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).