Re: [PATCH v2] iio: adc: ad7476: Add support for ADS786X ADCs

[Alexandru Ardelean <ardeleanalex@gmail.com>]

On Mon, Jan 28, 2019 at 9:43 AM Ricardo Ribalda Delgado
<ricardo@ribalda.com> wrote:
>
> HI Alexandru
>
> On Mon, Jan 28, 2019 at 8:38 AM Alexandru Ardelean
> <ardeleanalex@gmail.com> wrote:
> >
> > On Sat, Jan 26, 2019 at 8:21 PM Jonathan Cameron <jic23@kernel.org> wrote:
> > >
> > > On Fri, 25 Jan 2019 11:04:51 +0100
> > > Ricardo Ribalda Delgado <ricardo@ribalda.com> wrote:
> > >
> > > > Add support for ADS7866, ADS7867 and ADS7868 8/10/12 bit Single channel
> > > > ADC.
> > > >
> >
> > I don't want this reply be offensive or anything.
> > But since I've seen this precedence, I do have to ask if these driver
> > changes were tested on at least one of the TI chips/eval-boards.
> >
> > Ideally, before adding new drivers it would be nice to make sure that
> > they were run on actual HW.
> > Good code-review can get us only so far.
> >
> > We could ask someone who has any of these chips to test.
> > Or maybe some eval boards from TI could be obtained to test these changes.
> >
> > Overall changes seem good [I haven't taken a close look], but HW
> > testing is king.
> >
>
> I have access to ADS7868 (the 8 bit version) which has been connected
> in "loopback" to the ti-dac7612 (also new driver). I can run any test
> that you need or even give you or someone access (privately) to the
> board via vpn
> or something like that.
>
> Would that work for you?

No, that's fine :)
Thank you for the answer.
And apologies [again] if this was a bit too forward/harsh from my side.

Thanks
Alex

>
> Best regards!
>
> > Thanks
> > Alex
> >
> > > > Datasheet: http://www.ti.com/lit/ds/symlink/ads7868.pdf
> > > >
> > > > Signed-off-by: Ricardo Ribalda Delgado <ricardo@ribalda.com>
> > > > ---
> > > > v2: I have missnamed the devices
> > > >  drivers/iio/adc/Kconfig  |  3 ++-
> > > >  drivers/iio/adc/ad7476.c | 20 ++++++++++++++++++++
> > > >  2 files changed, 22 insertions(+), 1 deletion(-)
> > > >
> > > > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > > > index f9354e5ee65c..d86900fc2634 100644
> > > > --- a/drivers/iio/adc/Kconfig
> > > > +++ b/drivers/iio/adc/Kconfig
> > > > @@ -64,7 +64,8 @@ config AD7476
> > > >       help
> > > >         Say yes here to build support for Analog Devices AD7273, AD7274, AD7276,
> > > >         AD7277, AD7278, AD7475, AD7476, AD7477, AD7478, AD7466, AD7467, AD7468,
> > > > -       AD7495, AD7910, AD7920, AD7920 SPI analog to digital converters (ADC).
> > > > +       AD7495, AD7910, AD7920, AD7920, ADS7866, ADS7867, ADS7868 SPI analog
> > > > +       to digital converters (ADC).
> > >
> > > As commented in the earlier thread (after you sent this!), please make sure
> > > the help text makes it clear that these aren't all Analog devices parts.
> > >
> > > Likely to cause confusion otherwise.
> > >
> > > Good to see you didn't spin another driver but instead tracked down that
> > > this one would work well!
> > >
> > > Thanks,
> > >
> > > Jonathan
> > >
> > > >
> > > >         To compile this driver as a module, choose M here: the
> > > >         module will be called ad7476.
> > > > diff --git a/drivers/iio/adc/ad7476.c b/drivers/iio/adc/ad7476.c
> > > > index 0549686b9ef8..76747488044b 100644
> > > > --- a/drivers/iio/adc/ad7476.c
> > > > +++ b/drivers/iio/adc/ad7476.c
> > > > @@ -59,6 +59,9 @@ enum ad7476_supported_device_ids {
> > > >       ID_ADC081S,
> > > >       ID_ADC101S,
> > > >       ID_ADC121S,
> > > > +     ID_ADS7866,
> > > > +     ID_ADS7867,
> > > > +     ID_ADS7868,
> > > >  };
> > > >
> > > >  static irqreturn_t ad7476_trigger_handler(int irq, void  *p)
> > > > @@ -157,6 +160,8 @@ static int ad7476_read_raw(struct iio_dev *indio_dev,
> > > >  #define AD7940_CHAN(bits) _AD7476_CHAN((bits), 15 - (bits), \
> > > >               BIT(IIO_CHAN_INFO_RAW))
> > > >  #define AD7091R_CHAN(bits) _AD7476_CHAN((bits), 16 - (bits), 0)
> > > > +#define ADS786X_CHAN(bits) _AD7476_CHAN((bits), 12 - (bits), \
> > > > +             BIT(IIO_CHAN_INFO_RAW))
> > > >
> > > >  static const struct ad7476_chip_info ad7476_chip_info_tbl[] = {
> > > >       [ID_AD7091R] = {
> > > > @@ -209,6 +214,18 @@ static const struct ad7476_chip_info ad7476_chip_info_tbl[] = {
> > > >               .channel[0] = ADC081S_CHAN(12),
> > > >               .channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
> > > >       },
> > > > +     [ID_ADS7866] = {
> > > > +             .channel[0] = ADS786X_CHAN(12),
> > > > +             .channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
> > > > +     },
> > > > +     [ID_ADS7867] = {
> > > > +             .channel[0] = ADS786X_CHAN(10),
> > > > +             .channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
> > > > +     },
> > > > +     [ID_ADS7868] = {
> > > > +             .channel[0] = ADS786X_CHAN(8),
> > > > +             .channel[1] = IIO_CHAN_SOFT_TIMESTAMP(1),
> > > > +     },
> > > >  };
> > > >
> > > >  static const struct iio_info ad7476_info = {
> > > > @@ -314,6 +331,9 @@ static const struct spi_device_id ad7476_id[] = {
> > > >       {"adc081s", ID_ADC081S},
> > > >       {"adc101s", ID_ADC101S},
> > > >       {"adc121s", ID_ADC121S},
> > > > +     {"ads7866", ID_ADS7866},
> > > > +     {"ads7867", ID_ADS7867},
> > > > +     {"ads7868", ID_ADS7868},
> > > >       {}
> > > >  };
> > > >  MODULE_DEVICE_TABLE(spi, ad7476_id);
> > >
>
>
>
> --
> Ricardo Ribalda