From: Prabhakar Lad <prabhakar.csengg@gmail.com>
To: Sekhar Nori <nsekhar@ti.com>
Cc: DLOS <davinci-linux-open-source@linux.davincidsp.com>,
LAK <linux-arm-kernel@lists.infradead.org>,
devicetree-discuss@lists.ozlabs.org,
LKML <linux-kernel@vger.kernel.org>,
netdev@vger.kernel.org, Heiko Schocher <hs@denx.de>
Subject: Re: [PATCH v3 6/6] ARM: davinci: da850: configure system configuration chip(CFGCHIP3) for emac
Date: Thu, 8 Aug 2013 16:02:30 +0530 [thread overview]
Message-ID: <CA+V-a8smEd_75Ab-_vxjBATr8Q9Sefs0tpxc+kgQJRtuLJad=w@mail.gmail.com> (raw)
In-Reply-To: <51F8A4FF.8020803@ti.com>
Hi Sekhar,
Sorry for the delayed response I was on leave and now back again up
and running.
On Wed, Jul 31, 2013 at 11:17 AM, Sekhar Nori <nsekhar@ti.com> wrote:
> On Sunday 23 June 2013 08:30 PM, Prabhakar Lad wrote:
>> From: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
>>
>> This patch makes a common function for to configure emac and calls
>> it appropriately in DT and non DT boot mode. The system configuration
>> chip CFGCHIP3, controls the emac module. This patch appropriately
>> configures this register for emac and sets DA850_MII_MDIO_CLKEN_PIN
>> GPIO pin appropriately.
>>
[Snip]
>> + if (rmii_enabled)
>> + val |= BIT(8);
>> + else
>> + val &= ~BIT(8);
>> +
>> + /* configure the CFGCHIP3 register for RMII or MII */
>> + writel(val, cfg_chip3_base);
>> +
>> + ret = davinci_cfg_reg(DA850_GPIO2_6);
>> + if (ret)
>> + pr_warn("%s:GPIO(2,6) mux setup failed\n", __func__);
>> +
>> + ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en");
>> + if (ret) {
>> + pr_warn("Cannot open GPIO %d\n", DA850_MII_MDIO_CLKEN_PIN);
>> + return;
>> + }
>
> You cannot do this in SoC specific code. All boards wont use a GPIO to
> choose between MII/RMII. You need to do this in a EVM specific manner.
> This just means you retain the GPIO part of code in board-da850-evm.c
OK
> and for the DT case use a board specific GPIO node. See a similar
> example in arch/arm/boot/dts/ste-nomadik-s8815.dts and how the code uses
Alrite something similar to usb-s8815 node.
> it in arch/arm/mach-nomadik/cpu-8815.c.
>
But I don't see any code to access this node in this file, can
you point me to right direction ?
Regards,
--Prabhakar Lad
next prev parent reply other threads:[~2013-08-08 10:32 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-06-23 15:00 [PATCH v3 0/6] ARM: davinci: da850: add ethernet driver DT support Prabhakar Lad
2013-06-23 15:00 ` [PATCH v3 1/6] ARM: davinci: da8xx: fix clock lookup for mdio device Prabhakar Lad
2013-08-14 12:04 ` Sekhar Nori
2013-06-23 15:00 ` [PATCH v3 2/6] ARM: davinci: da850: add DT node " Prabhakar Lad
2013-06-23 15:00 ` [PATCH v3 3/6] ARM: davinci: da850: add OF_DEV_AUXDATA entry for mdio Prabhakar Lad
2013-06-23 15:00 ` [PATCH v3 4/6] ARM: davinci: da850: add DT node for eth0 Prabhakar Lad
2013-06-23 15:00 ` [PATCH v3 5/6] ARM: davinci: da850: add OF_DEV_AUXDATA entry " Prabhakar Lad
2013-06-23 15:00 ` [PATCH v3 6/6] ARM: davinci: da850: configure system configuration chip(CFGCHIP3) for emac Prabhakar Lad
2013-07-31 5:47 ` Sekhar Nori
2013-08-08 10:32 ` Prabhakar Lad [this message]
2013-08-08 16:05 ` Sekhar Nori
2013-08-08 10:39 ` Prabhakar Lad
2013-07-11 17:12 ` [PATCH v3 0/6] ARM: davinci: da850: add ethernet driver DT support Prabhakar Lad
2013-07-12 6:51 ` Sekhar Nori
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CA+V-a8smEd_75Ab-_vxjBATr8Q9Sefs0tpxc+kgQJRtuLJad=w@mail.gmail.com' \
--to=prabhakar.csengg@gmail.com \
--cc=davinci-linux-open-source@linux.davincidsp.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=hs@denx.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=nsekhar@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).