From: Linu Cherian <linuc.decode@gmail.com> To: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: linux-arm-kernel <linux-arm-kernel@lists.infradead.org>, Mark Rutland <mark.rutland@arm.com>, maz@kernel.org, Anshuman Khandual <anshuman.khandual@arm.com>, catalin.marinas@arm.com, Coresight ML <coresight@lists.linaro.org>, linux-kernel@vger.kernel.org, james.morse@arm.com, Will Deacon <will@kernel.org>, Mike Leach <mike.leach@linaro.org> Subject: Re: [PATCH 08/10] coresight: trbe: Workaround TRBE errat overwrite in FILL mode Date: Fri, 6 Aug 2021 21:39:43 +0530 [thread overview] Message-ID: <CAAHhmWjR6XYo5j_h3jfLsmWzqD9i9L-pHq=zrrdrw9YTXmuCqg@mail.gmail.com> (raw) In-Reply-To: <20210728135217.591173-9-suzuki.poulose@arm.com> Hi Suzuki, On Wed, Jul 28, 2021 at 7:23 PM Suzuki K Poulose <suzuki.poulose@arm.com> wrote: > > ARM Neoverse-N2 (#2139208) and Cortex-A710(##2119858) suffers from > an erratum, which when triggered, might cause the TRBE to overwrite > the trace data already collected in FILL mode, in the event of a WRAP. > i.e, the TRBE doesn't stop writing the data, instead wraps to the base > and could write upto 3 cache line size worth trace. Thus, this could > corrupt the trace at the "BASE" pointer. > > The workaround is to program the write pointer 256bytes from the > base, such that if the erratum is triggered, it doesn't overwrite > the trace data that was captured. This skipped region could be > padded with ignore packets at the end of the session, so that > the decoder sees a continuous buffer with some padding at the > beginning. Just trying to understand, Is there a possibility that lost data results in partial trace packets towards the end of the buffer ? Or its always guaranteed that trace packet end is always aligned with buffer end/limit ? Thinking of a case when formatting is disabled. The trace data written at the base is considered > lost as the limit could have been in the middle of the perf > ring buffer, and jumping to the "base" is not acceptable. > We set the flags already to indicate that some amount of trace > was lost during the FILL event IRQ. So this is fine. > > One important change with the work around is, we program the > TRBBASER_EL1 to current page where we are allowed to write. > Otherwise, it could overwrite a region that may be consumed > by the perf. Towards this, we always make sure that the > "handle->head" and thus the trbe_write is PAGE_SIZE aligned, > so that we can set the BASE to the PAGE base and move the > TRBPTR to the 256bytes offset. > > Cc: Mike Leach <mike.leach@linaro.org> > Cc: Mathieu Poirier <mathieu.poirier@linaro.org> > Cc: Anshuman Khandual <anshuman.khandual@arm.com> > Cc: Leo Yan <leo.yan@linaro.org> > Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> > --- > drivers/hwtracing/coresight/coresight-trbe.c | 111 +++++++++++++++++-- > 1 file changed, 102 insertions(+), 9 deletions(-) > > diff --git a/drivers/hwtracing/coresight/coresight-trbe.c b/drivers/hwtracing/coresight/coresight-trbe.c > index 9ea28813182b..cd997ed5d918 100644 > --- a/drivers/hwtracing/coresight/coresight-trbe.c > +++ b/drivers/hwtracing/coresight/coresight-trbe.c > @@ -17,6 +17,7 @@ > > #include <asm/barrier.h> > #include <asm/cputype.h> > +#include <asm/cpufeature.h> > > #include "coresight-self-hosted-trace.h" > #include "coresight-trbe.h" > @@ -84,9 +85,17 @@ struct trbe_buf { > * per TRBE instance, we keep track of the list of errata that > * affects the given instance of the TRBE. > */ > -#define TRBE_ERRATA_MAX 0 > +#define TRBE_WORKAROUND_OVERWRITE_FILL_MODE 0 > +#define TRBE_ERRATA_MAX 1 > + > +/* > + * Safe limit for the number of bytes that may be overwritten > + * when the erratum is triggered. > + */ > +#define TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP 256 > > static unsigned long trbe_errata_cpucaps[TRBE_ERRATA_MAX] = { > + [TRBE_WORKAROUND_OVERWRITE_FILL_MODE] = ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE, > }; > > /* > @@ -531,10 +540,13 @@ static enum trbe_fault_action trbe_get_fault_act(u64 trbsr) > if ((ec == TRBE_EC_STAGE1_ABORT) || (ec == TRBE_EC_STAGE2_ABORT)) > return TRBE_FAULT_ACT_FATAL; > > - if (is_trbe_wrap(trbsr) && (ec == TRBE_EC_OTHERS) && (bsc == TRBE_BSC_FILLED)) { > - if (get_trbe_write_pointer() == get_trbe_base_pointer()) > - return TRBE_FAULT_ACT_WRAP; > - } > + /* > + * It is not necessary to verify the TRBPTR == TRBBASER to detect > + * a FILL event. Moreover, CPU errata could make this check invalid. > + */ > + if (is_trbe_wrap(trbsr) && (ec == TRBE_EC_OTHERS) && (bsc == TRBE_BSC_FILLED)) > + return TRBE_FAULT_ACT_WRAP; > + > return TRBE_FAULT_ACT_SPURIOUS; > } > > @@ -544,6 +556,7 @@ static unsigned long trbe_get_trace_size(struct perf_output_handle *handle, > { > u64 write; > u64 start_off, end_off; > + u64 size; > > /* > * If the TRBE has wrapped around the write pointer has > @@ -559,7 +572,18 @@ static unsigned long trbe_get_trace_size(struct perf_output_handle *handle, > > if (WARN_ON_ONCE(end_off < start_off)) > return 0; > - return (end_off - start_off); > + > + size = end_off - start_off; > + /* > + * If the TRBE is affected by the following erratum, we must fill > + * the space we skipped with IGNORE packets. And we are always > + * guaranteed to have at least a PAGE_SIZE space in the buffer. > + */ > + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, buf->cpudata) && > + !WARN_ON(size < TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP)) > + __trbe_pad_buf(buf, start_off, TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP); > + > + return size; > } > > static void *arm_trbe_alloc_buffer(struct coresight_device *csdev, > @@ -704,20 +728,73 @@ static unsigned long arm_trbe_update_buffer(struct coresight_device *csdev, > return size; > } > > + > +static int trbe_apply_work_around_before_enable(struct trbe_buf *buf) > +{ > + /* > + * TRBE_WORKAROUND_OVERWRITE_FILL_MODE causes the TRBE to overwrite a few cache > + * line size from the "TRBBASER_EL1" in the event of a "FILL". > + * Thus, we could loose some amount of the trace at the base. > + * > + * To work around this: > + * - Software must leave 256bytes of space from the base, so that > + * the trace collected now is not overwritten. > + * - Fill the first 256bytes with IGNORE packets for the decoder > + * to ignore at the end of the session, so that the decoder ignores > + * this gap. > + * > + * This also means that, the TRBE driver must set the TRBBASER_EL1 > + * such that, when the erratum is triggered, it doesn't overwrite > + * the "area" outside the area marked by (handle->head, +size). > + * So, we make sure that the handle->head is always PAGE aligned, > + * by tweaking the required alignment for the TRBE (trbe_align). > + * And when we enable the TRBE, > + * > + * - move the TRBPTR_EL1 to 256bytes past the starting point. > + * So that any trace collected in this run is not overwritten. > + * > + * - set the TRBBASER_EL1 to the original trbe_write. This will > + * ensure that, if the TRBE hits the erratum, it would only > + * write within the region allowed for the TRBE. > + * > + * At the trace collection time, we always pad the skipped bytes > + * with IGNORE packets to make sure the decoder doesn't see any > + * overwritten packets. > + */ > + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, buf->cpudata)) { > + if (WARN_ON(!IS_ALIGNED(buf->trbe_write, PAGE_SIZE))) > + return -EINVAL; > + buf->trbe_hw_base = buf->trbe_write; > + buf->trbe_write += TRBE_WORKAROUND_OVERWRITE_FILL_MODE_SKIP; > + } > + > + return 0; > +} > + > static int __arm_trbe_enable(struct trbe_buf *buf, > struct perf_output_handle *handle) > { > + int ret = 0; > + > buf->trbe_limit = compute_trbe_buffer_limit(handle); > buf->trbe_write = buf->trbe_base + PERF_IDX2OFF(handle->head, buf); > if (buf->trbe_limit == buf->trbe_base) { > - trbe_stop_and_truncate_event(handle); > - return -ENOSPC; > + ret = -ENOSPC; > + goto err; > } > /* Set the base of the TRBE to the buffer base */ > buf->trbe_hw_base = buf->trbe_base; > + > + ret = trbe_apply_work_around_before_enable(buf); > + if (ret) > + goto err; > + > *this_cpu_ptr(buf->cpudata->drvdata->handle) = handle; > trbe_enable_hw(buf); > return 0; > +err: > + trbe_stop_and_truncate_event(handle); > + return ret; > } > > static int arm_trbe_enable(struct coresight_device *csdev, u32 mode, void *data) > @@ -1003,7 +1080,23 @@ static void arm_trbe_probe_cpu(void *info) > pr_err("Unsupported alignment on cpu %d\n", cpu); > goto cpu_clear; > } > - cpudata->trbe_align = cpudata->trbe_hw_align; > + > + /* > + * If the TRBE is affected by erratum TRBE_WORKAROUND_OVERWRITE_FILL_MODE, > + * we must always program the TBRPTR_EL1, 256bytes from a page > + * boundary, with TRBBASER_EL1 set to the page, to prevent > + * TRBE over-writing 256bytes at TRBBASER_EL1 on FILL event. > + * > + * Thus make sure we always align our write pointer to a PAGE_SIZE, > + * which also guarantees that we have at least a PAGE_SIZE space in > + * the buffer (TRBLIMITR is PAGE aligned) and thus we can skip > + * the required bytes at the base. > + */ > + if (trbe_has_erratum(TRBE_WORKAROUND_OVERWRITE_FILL_MODE, cpudata)) > + cpudata->trbe_align = PAGE_SIZE; > + else > + cpudata->trbe_align = cpudata->trbe_hw_align; > + > cpudata->trbe_flag = get_trbe_flag_update(trbidr); > cpudata->cpu = cpu; > cpudata->drvdata = drvdata; > -- > 2.24.1 > > _______________________________________________ > CoreSight mailing list > CoreSight@lists.linaro.org > https://lists.linaro.org/mailman/listinfo/coresight
next prev parent reply other threads:[~2021-08-06 16:10 UTC|newest] Thread overview: 42+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-07-28 13:52 [PATCH 00/10] arm64: Self-hosted trace related erratum workarouds Suzuki K Poulose 2021-07-28 13:52 ` [PATCH 01/10] coresight: trbe: Add infrastructure for Errata handling Suzuki K Poulose 2021-08-02 6:43 ` Anshuman Khandual 2021-09-07 9:04 ` Suzuki K Poulose 2021-09-09 2:55 ` Anshuman Khandual 2021-07-28 13:52 ` [PATCH 02/10] coresight: trbe: Add a helper to calculate the trace generated Suzuki K Poulose 2021-07-30 10:01 ` Anshuman Khandual 2021-07-28 13:52 ` [PATCH 03/10] coresight: trbe: Add a helper to pad a given buffer area Suzuki K Poulose 2021-07-30 10:05 ` Anshuman Khandual 2021-07-28 13:52 ` [PATCH 04/10] coresight: trbe: Decouple buffer base from the hardware base Suzuki K Poulose 2021-07-30 10:53 ` Anshuman Khandual 2021-07-28 13:52 ` [PATCH 05/10] coresight: trbe: Allow driver to choose a different alignment Suzuki K Poulose 2021-07-30 11:02 ` Anshuman Khandual 2021-07-30 14:29 ` Suzuki K Poulose 2021-07-28 13:52 ` [PATCH 06/10] arm64: Add Neoverse-N2, Cortex-A710 CPU part definition Suzuki K Poulose 2021-07-30 11:26 ` Anshuman Khandual 2021-07-30 14:31 ` Suzuki K Poulose 2021-08-02 11:21 ` Catalin Marinas 2021-08-02 11:21 ` Catalin Marinas 2021-07-28 13:52 ` [PATCH 07/10] arm64: Add erratum detection for TRBE overwrite in FILL mode Suzuki K Poulose 2021-08-02 7:44 ` Anshuman Khandual 2021-08-02 11:22 ` Catalin Marinas 2021-08-06 12:44 ` Linu Cherian 2021-09-07 9:10 ` Suzuki K Poulose 2021-07-28 13:52 ` [PATCH 08/10] coresight: trbe: Workaround TRBE errat " Suzuki K Poulose 2021-08-03 10:25 ` Anshuman Khandual 2021-09-07 9:58 ` Suzuki K Poulose 2021-09-09 4:21 ` Anshuman Khandual 2021-09-09 8:37 ` Suzuki K Poulose 2021-08-06 16:09 ` Linu Cherian [this message] 2021-09-07 9:18 ` Suzuki K Poulose 2021-07-28 13:52 ` [PATCH 09/10] arm64: Enable workaround for TRBE " Suzuki K Poulose 2021-08-02 9:34 ` Anshuman Khandual 2021-08-02 11:24 ` Catalin Marinas 2021-07-28 13:52 ` [PATCH 10/10] arm64: errata: Add workaround for TSB flush failures Suzuki K Poulose 2021-07-29 9:55 ` Marc Zyngier 2021-07-29 10:41 ` Suzuki K Poulose 2021-08-02 9:12 ` Anshuman Khandual 2021-08-02 9:35 ` Marc Zyngier 2021-08-03 3:51 ` Anshuman Khandual 2021-09-08 13:39 ` Suzuki K Poulose 2021-08-02 11:27 ` Catalin Marinas
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to='CAAHhmWjR6XYo5j_h3jfLsmWzqD9i9L-pHq=zrrdrw9YTXmuCqg@mail.gmail.com' \ --to=linuc.decode@gmail.com \ --cc=anshuman.khandual@arm.com \ --cc=catalin.marinas@arm.com \ --cc=coresight@lists.linaro.org \ --cc=james.morse@arm.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=maz@kernel.org \ --cc=mike.leach@linaro.org \ --cc=suzuki.poulose@arm.com \ --cc=will@kernel.org \ --subject='Re: [PATCH 08/10] coresight: trbe: Workaround TRBE errat overwrite in FILL mode' \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: link
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).