[PATCH v2 0/6] VAG power control improvement for sgtl5000 codec

[PATCH v2 0/6] VAG power control improvement for sgtl5000 codec

[Oleksandr Suvorov]

VAG power control is improved to fit the manual. This fixes as
minimum one bug: if customer muxes Headphone to Line-In right after boot
w/o playing any sound, the VAG power remains off that leads to poor
sound quality from line-in.

I.e. after boot:
- Connect sound source to Line-In jack;
- Connect headphone to HP jack;
- Run following commands:
$ amixer set 'Headphone' 80%
$ amixer set 'Headphone Mux' LINE_IN

Also this series includes fixes of non-important bugs in sgtl5000 codec
driver.

Fix patch formatting in patchset v2.


Oleksandr Suvorov (6):
  ASoC: sgtl5000: Fix definition of VAG Ramp Control
  ASoC: sgtl5000: add ADC mute control
  ASoC: sgtl5000: Fix of unmute outputs on probe
  ASoC: sgtl5000: Fix charge pump source assignment
  ASoC: Define a set of DAPM pre/post-up events
  ASoC: sgtl5000: Improve VAG power and mute control

 include/sound/soc-dapm.h    |   2 +
 sound/soc/codecs/sgtl5000.c | 250 ++++++++++++++++++++++++++++++------
 sound/soc/codecs/sgtl5000.h |   2 +-
 3 files changed, 212 insertions(+), 42 deletions(-)

-- 
2.20.1

[PATCH v2 1/6] ASoC: sgtl5000: Fix definition of VAG Ramp Control

[Oleksandr Suvorov]

SGTL5000_SMALL_POP is a bit mask, not a value. Usage of
correct definition makes device probing code more clear.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 sound/soc/codecs/sgtl5000.c | 2 +-
 sound/soc/codecs/sgtl5000.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index a6a4748c97f9d..5e49523ee0b67 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -1296,7 +1296,7 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 
 	/* enable small pop, introduce 400ms delay in turning off */
 	snd_soc_component_update_bits(component, SGTL5000_CHIP_REF_CTRL,
-				SGTL5000_SMALL_POP, 1);
+				SGTL5000_SMALL_POP, SGTL5000_SMALL_POP);
 
 	/* disable short cut detector */
 	snd_soc_component_write(component, SGTL5000_CHIP_SHORT_CTRL, 0);
diff --git a/sound/soc/codecs/sgtl5000.h b/sound/soc/codecs/sgtl5000.h
index 18cae08bbd3a6..a4bf4bca95bf7 100644
--- a/sound/soc/codecs/sgtl5000.h
+++ b/sound/soc/codecs/sgtl5000.h
@@ -273,7 +273,7 @@
 #define SGTL5000_BIAS_CTRL_MASK			0x000e
 #define SGTL5000_BIAS_CTRL_SHIFT		1
 #define SGTL5000_BIAS_CTRL_WIDTH		3
-#define SGTL5000_SMALL_POP			1
+#define SGTL5000_SMALL_POP			0x0001
 
 /*
  * SGTL5000_CHIP_MIC_CTRL
-- 
2.20.1

[PATCH v2 2/6] ASoC: sgtl5000: add ADC mute control

[Oleksandr Suvorov]

This control mute/unmute the ADC input of SGTL5000
using its CHIP_ANA_CTRL register.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 sound/soc/codecs/sgtl5000.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index 5e49523ee0b67..bb58c997c6914 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -556,6 +556,7 @@ static const struct snd_kcontrol_new sgtl5000_snd_controls[] = {
 			SGTL5000_CHIP_ANA_ADC_CTRL,
 			8, 1, 0, capture_6db_attenuate),
 	SOC_SINGLE("Capture ZC Switch", SGTL5000_CHIP_ANA_CTRL, 1, 1, 0),
+	SOC_SINGLE("Capture Switch", SGTL5000_CHIP_ANA_CTRL, 0, 1, 1),
 
 	SOC_DOUBLE_TLV("Headphone Playback Volume",
 			SGTL5000_CHIP_ANA_HP_CTRL,
-- 
2.20.1

[PATCH v2 3/6] ASoC: sgtl5000: Fix of unmute outputs on probe

[Oleksandr Suvorov]

To enable "zero cross detect" for ADC/HP, change
HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole
CHIP_ANA_CTRL register.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 sound/soc/codecs/sgtl5000.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index bb58c997c6914..e813a37910af4 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -1289,6 +1289,7 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 	int ret;
 	u16 reg;
 	struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
+	unsigned int zcd_mask = SGTL5000_HP_ZCD_EN | SGTL5000_ADC_ZCD_EN;
 
 	/* power up sgtl5000 */
 	ret = sgtl5000_set_power_regs(component);
@@ -1316,9 +1317,8 @@ static int sgtl5000_probe(struct snd_soc_component *component)
 	       0x1f);
 	snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);
 
-	snd_soc_component_write(component, SGTL5000_CHIP_ANA_CTRL,
-			SGTL5000_HP_ZCD_EN |
-			SGTL5000_ADC_ZCD_EN);
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+		zcd_mask, zcd_mask);
 
 	snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
 			SGTL5000_BIAS_R_MASK,
-- 
2.20.1

[PATCH v2 4/6] ASoC: sgtl5000: Fix charge pump source assignment

[Oleksandr Suvorov]

If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
source can be assigned automatically.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 sound/soc/codecs/sgtl5000.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index e813a37910af4..ee1e4bf613227 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -1174,12 +1174,16 @@ static int sgtl5000_set_power_regs(struct snd_soc_component *component)
 					SGTL5000_INT_OSC_EN);
 		/* Enable VDDC charge pump */
 		ana_pwr |= SGTL5000_VDDC_CHRGPMP_POWERUP;
-	} else if (vddio >= 3100 && vdda >= 3100) {
+	} else {
 		ana_pwr &= ~SGTL5000_VDDC_CHRGPMP_POWERUP;
-		/* VDDC use VDDIO rail */
-		lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
-		lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
-			    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		/* if vddio == vdda the source of charge pump should be
+		 * assigned manually to VDDIO
+		 */
+		if (vddio == vdda) {
+			lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
+			lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
+				    SGTL5000_VDDC_MAN_ASSN_SHIFT;
+		}
 	}
 
 	snd_soc_component_write(component, SGTL5000_CHIP_LINREG_CTRL, lreg_ctrl);
-- 
2.20.1

[PATCH v2 5/6] ASoC: Define a set of DAPM pre/post-up events

[Oleksandr Suvorov]

Prepare to use SND_SOC_DAPM_PRE_POST_PMU definition to
reduce coming code size and make it more readable.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 include/sound/soc-dapm.h | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/include/sound/soc-dapm.h b/include/sound/soc-dapm.h
index c00a0b8ade086..6c66941601307 100644
--- a/include/sound/soc-dapm.h
+++ b/include/sound/soc-dapm.h
@@ -353,6 +353,8 @@ struct device;
 #define SND_SOC_DAPM_WILL_PMD   0x80    /* called at start of sequence */
 #define SND_SOC_DAPM_PRE_POST_PMD \
 				(SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMD)
+#define SND_SOC_DAPM_PRE_POST_PMU \
+				(SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU)
 
 /* convenience event type detection */
 #define SND_SOC_DAPM_EVENT_ON(e)	\
-- 
2.20.1

[PATCH v2 6/6] ASoC: sgtl5000: Improve VAG power and mute control

[Oleksandr Suvorov]

Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
  come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
  prevents pop during line-in muxing.

Also, according to the manual, to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
---

 sound/soc/codecs/sgtl5000.c | 227 +++++++++++++++++++++++++++++++-----
 1 file changed, 195 insertions(+), 32 deletions(-)

diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
index ee1e4bf613227..acfbd5cdf936e 100644
--- a/sound/soc/codecs/sgtl5000.c
+++ b/sound/soc/codecs/sgtl5000.c
@@ -31,6 +31,13 @@
 #define SGTL5000_DAP_REG_OFFSET	0x0100
 #define SGTL5000_MAX_REG_OFFSET	0x013A
 
+/* Delay for the VAG ramp up */
+#define SGTL5000_VAG_POWERUP_DELAY 500 /* ms */
+/* Delay for the VAG ramp down */
+#define SGTL5000_VAG_POWERDOWN_DELAY 500 /* ms */
+
+#define SGTL5000_OUTPUTS_MUTE (SGTL5000_HP_MUTE | SGTL5000_LINE_OUT_MUTE)
+
 /* default value of sgtl5000 registers */
 static const struct reg_default sgtl5000_reg_defaults[] = {
 	{ SGTL5000_CHIP_DIG_POWER,		0x0000 },
@@ -123,6 +130,18 @@ enum  {
 	I2S_SCLK_STRENGTH_HIGH,
 };
 
+enum {
+	HP_POWER_EVENT,
+	DAC_POWER_EVENT,
+	ADC_POWER_EVENT
+};
+
+struct sgtl5000_mute_state {
+	u16 hp_event;
+	u16 dac_event;
+	u16 adc_event;
+};
+
 /* sgtl5000 private structure in codec */
 struct sgtl5000_priv {
 	int sysclk;	/* sysclk rate */
@@ -137,8 +156,109 @@ struct sgtl5000_priv {
 	u8 micbias_voltage;
 	u8 lrclk_strength;
 	u8 sclk_strength;
+	struct sgtl5000_mute_state mute_state;
 };
 
+static inline int hp_sel_input(struct snd_soc_component *component)
+{
+	return (snd_soc_component_read32(component, SGTL5000_CHIP_ANA_CTRL) &
+		SGTL5000_HP_SEL_MASK) >> SGTL5000_HP_SEL_SHIFT;
+}
+
+static inline u16 mute_output(struct snd_soc_component *component,
+			      u16 mute_mask)
+{
+	u16 mute_reg = snd_soc_component_read32(component,
+					      SGTL5000_CHIP_ANA_CTRL);
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+			    mute_mask, mute_mask);
+	return mute_reg;
+}
+
+static inline void restore_output(struct snd_soc_component *component,
+				  u16 mute_mask, u16 mute_reg)
+{
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+		mute_mask, mute_reg);
+}
+
+static void vag_power_on(struct snd_soc_component *component, u32 source)
+{
+	if (snd_soc_component_read32(component, SGTL5000_CHIP_ANA_POWER) &
+	    SGTL5000_VAG_POWERUP)
+		return;
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
+			    SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);
+
+	/* When VAG powering on to get local loop from Line-In, the sleep
+	 * is required to avoid loud pop.
+	 */
+	if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN &&
+	    source == HP_POWER_EVENT)
+		msleep(SGTL5000_VAG_POWERUP_DELAY);
+}
+
+static int vag_power_consumers(struct snd_soc_component *component,
+			       u16 ana_pwr_reg, u32 source)
+{
+	int consumers = 0;
+
+	/* count dac/adc consumers unconditional */
+	if (ana_pwr_reg & SGTL5000_DAC_POWERUP)
+		consumers++;
+	if (ana_pwr_reg & SGTL5000_ADC_POWERUP)
+		consumers++;
+
+	/*
+	 * If the event comes from HP and Line-In is selected,
+	 * current action is 'DAC to be powered down'.
+	 * As HP_POWERUP is not set when HP muxed to line-in,
+	 * we need to keep VAG power ON.
+	 */
+	if (source == HP_POWER_EVENT) {
+		if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN)
+			consumers++;
+	} else {
+		if (ana_pwr_reg & SGTL5000_HP_POWERUP)
+			consumers++;
+	}
+
+	return consumers;
+}
+
+static void vag_power_off(struct snd_soc_component *component, u32 source)
+{
+	u16 ana_pwr = snd_soc_component_read32(component,
+					     SGTL5000_CHIP_ANA_POWER);
+
+	if (!(ana_pwr & SGTL5000_VAG_POWERUP))
+		return;
+
+	/*
+	 * This function calls when any of VAG power consumers is disappearing.
+	 * Thus, if there is more than one consumer at the moment, as minimum
+	 * one consumer will definitely stay after the end of the current
+	 * event.
+	 * Don't clear VAG_POWERUP if 2 or more consumers of VAG present:
+	 * - LINE_IN (for HP events) / HP (for DAC/ADC events)
+	 * - DAC
+	 * - ADC
+	 * (the current consumer is disappearing right now)
+	 */
+	if (vag_power_consumers(component, ana_pwr, source) >= 2)
+		return;
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
+		SGTL5000_VAG_POWERUP, 0);
+	/* In power down case, we need wait 400-1000 ms
+	 * when VAG fully ramped down.
+	 * As longer we wait, as smaller pop we've got.
+	 */
+	msleep(SGTL5000_VAG_POWERDOWN_DELAY);
+}
+
 /*
  * mic_bias power on/off share the same register bits with
  * output impedance of mic bias, when power on mic bias, we
@@ -170,40 +290,79 @@ static int mic_bias_event(struct snd_soc_dapm_widget *w,
 	return 0;
 }
 
-/*
- * As manual described, ADC/DAC only works when VAG powerup,
- * So enabled VAG before ADC/DAC up.
- * In power down case, we need wait 400ms when vag fully ramped down.
- */
-static int power_vag_event(struct snd_soc_dapm_widget *w,
-	struct snd_kcontrol *kcontrol, int event)
+static void vag_and_mute_control(struct snd_soc_component *component,
+				 int event, int event_source,
+				 u16 mute_mask, u16 *mute_reg)
 {
-	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
-	const u32 mask = SGTL5000_DAC_POWERUP | SGTL5000_ADC_POWERUP;
-
 	switch (event) {
-	case SND_SOC_DAPM_POST_PMU:
-		snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
-			SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);
-		msleep(400);
+	case SND_SOC_DAPM_PRE_PMU:
+		*mute_reg = mute_output(component, mute_mask);
+		break;
+	case SND_SOC_DAPM_POST_PMU:
+		vag_power_on(component, event_source);
+		restore_output(component, mute_mask, *mute_reg);
 		break;
-
 	case SND_SOC_DAPM_PRE_PMD:
-		/*
-		 * Don't clear VAG_POWERUP, when both DAC and ADC are
-		 * operational to prevent inadvertently starving the
-		 * other one of them.
-		 */
-		if ((snd_soc_component_read32(component, SGTL5000_CHIP_ANA_POWER) &
-				mask) != mask) {
-			snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
-				SGTL5000_VAG_POWERUP, 0);
-			msleep(400);
-		}
+		*mute_reg = mute_output(component, mute_mask);
+		vag_power_off(component, event_source);
+		break;
+	case SND_SOC_DAPM_POST_PMD:
+		restore_output(component, mute_mask, *mute_reg);
 		break;
 	default:
 		break;
 	}
+}
+
+/*
+ * Mute Headphone when power it up/down.
+ * Control VAG power on HP power path.
+ */
+static int headphone_pga_event(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, HP_POWER_EVENT,
+			     SGTL5000_HP_MUTE,
+			     &sgtl5000->mute_state.hp_event);
+
+	return 0;
+}
+
+/* As manual describes, ADC/DAC powering up/down requires
+ * to mute outputs to avoid pops.
+ * Control VAG power on ADC/DAC power path.
+ */
+static int adc_updown_depop(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, ADC_POWER_EVENT,
+			     SGTL5000_OUTPUTS_MUTE,
+			     &sgtl5000->mute_state.adc_event);
+
+	return 0;
+}
+
+static int dac_updown_depop(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, DAC_POWER_EVENT,
+			     SGTL5000_OUTPUTS_MUTE,
+			     &sgtl5000->mute_state.dac_event);
 
 	return 0;
 }
@@ -280,7 +439,10 @@ static const struct snd_soc_dapm_widget sgtl5000_dapm_widgets[] = {
 			    mic_bias_event,
 			    SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
 
-	SND_SOC_DAPM_PGA("HP", SGTL5000_CHIP_ANA_POWER, 4, 0, NULL, 0),
+	SND_SOC_DAPM_PGA_E("HP", SGTL5000_CHIP_ANA_POWER, 4, 0, NULL, 0,
+			   headphone_pga_event,
+			   SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
 	SND_SOC_DAPM_PGA("LO", SGTL5000_CHIP_ANA_POWER, 0, 0, NULL, 0),
 
 	SND_SOC_DAPM_MUX("Capture Mux", SND_SOC_NOPM, 0, 0, &adc_mux),
@@ -301,11 +463,12 @@ static const struct snd_soc_dapm_widget sgtl5000_dapm_widgets[] = {
 				0, SGTL5000_CHIP_DIG_POWER,
 				1, 0),
 
-	SND_SOC_DAPM_ADC("ADC", "Capture", SGTL5000_CHIP_ANA_POWER, 1, 0),
-	SND_SOC_DAPM_DAC("DAC", "Playback", SGTL5000_CHIP_ANA_POWER, 3, 0),
-
-	SND_SOC_DAPM_PRE("VAG_POWER_PRE", power_vag_event),
-	SND_SOC_DAPM_POST("VAG_POWER_POST", power_vag_event),
+	SND_SOC_DAPM_ADC_E("ADC", "Capture", SGTL5000_CHIP_ANA_POWER, 1, 0,
+			   adc_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
+	SND_SOC_DAPM_DAC_E("DAC", "Playback", SGTL5000_CHIP_ANA_POWER, 3, 0,
+			   dac_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
 };
 
 /* routes for sgtl5000 */
-- 
2.20.1

Re: [PATCH v2 1/6] ASoC: sgtl5000: Fix definition of VAG Ramp Control

[Igor Opaniuk]

On Tue, Jun 25, 2019 at 10:55 AM Oleksandr Suvorov
<oleksandr.suvorov@toradex.com> wrote:
>
> SGTL5000_SMALL_POP is a bit mask, not a value. Usage of
> correct definition makes device probing code more clear.
>
> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
>
>  sound/soc/codecs/sgtl5000.c | 2 +-
>  sound/soc/codecs/sgtl5000.h | 2 +-
>  2 files changed, 2 insertions(+), 2 deletions(-)
>
> diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
> index a6a4748c97f9d..5e49523ee0b67 100644
> --- a/sound/soc/codecs/sgtl5000.c
> +++ b/sound/soc/codecs/sgtl5000.c
> @@ -1296,7 +1296,7 @@ static int sgtl5000_probe(struct snd_soc_component *component)
>
>         /* enable small pop, introduce 400ms delay in turning off */
>         snd_soc_component_update_bits(component, SGTL5000_CHIP_REF_CTRL,
> -                               SGTL5000_SMALL_POP, 1);
> +                               SGTL5000_SMALL_POP, SGTL5000_SMALL_POP);
>
>         /* disable short cut detector */
>         snd_soc_component_write(component, SGTL5000_CHIP_SHORT_CTRL, 0);
> diff --git a/sound/soc/codecs/sgtl5000.h b/sound/soc/codecs/sgtl5000.h
> index 18cae08bbd3a6..a4bf4bca95bf7 100644
> --- a/sound/soc/codecs/sgtl5000.h
> +++ b/sound/soc/codecs/sgtl5000.h
> @@ -273,7 +273,7 @@
>  #define SGTL5000_BIAS_CTRL_MASK                        0x000e
>  #define SGTL5000_BIAS_CTRL_SHIFT               1
>  #define SGTL5000_BIAS_CTRL_WIDTH               3
> -#define SGTL5000_SMALL_POP                     1
> +#define SGTL5000_SMALL_POP                     0x0001
>
>  /*
>   * SGTL5000_CHIP_MIC_CTRL
> --
> 2.20.1
>

Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)

Re: [PATCH v2 2/6] ASoC: sgtl5000: add ADC mute control

[Igor Opaniuk]

On Tue, Jun 25, 2019 at 10:49 AM Oleksandr Suvorov
<oleksandr.suvorov@toradex.com> wrote:
>
> This control mute/unmute the ADC input of SGTL5000
> using its CHIP_ANA_CTRL register.
>
> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
>
>  sound/soc/codecs/sgtl5000.c | 1 +
>  1 file changed, 1 insertion(+)
>
> diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
> index 5e49523ee0b67..bb58c997c6914 100644
> --- a/sound/soc/codecs/sgtl5000.c
> +++ b/sound/soc/codecs/sgtl5000.c
> @@ -556,6 +556,7 @@ static const struct snd_kcontrol_new sgtl5000_snd_controls[] = {
>                         SGTL5000_CHIP_ANA_ADC_CTRL,
>                         8, 1, 0, capture_6db_attenuate),
>         SOC_SINGLE("Capture ZC Switch", SGTL5000_CHIP_ANA_CTRL, 1, 1, 0),
> +       SOC_SINGLE("Capture Switch", SGTL5000_CHIP_ANA_CTRL, 0, 1, 1),
>
>         SOC_DOUBLE_TLV("Headphone Playback Volume",
>                         SGTL5000_CHIP_ANA_HP_CTRL,
> --
> 2.20.1
>

Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)

Re: [PATCH v2 4/6] ASoC: sgtl5000: Fix charge pump source assignment

[Igor Opaniuk]

Hi Oleksandr,

On Tue, Jun 25, 2019 at 10:56 AM Oleksandr Suvorov
<oleksandr.suvorov@toradex.com> wrote:
>
> If VDDA != VDDIO and any of them is greater than 3.1V, charge pump
> source can be assigned automatically.
minor: Could also you please add a reference link to the commit message,
where this behavior is defined?

>
> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
>
>  sound/soc/codecs/sgtl5000.c | 14 +++++++++-----
>  1 file changed, 9 insertions(+), 5 deletions(-)
>
> diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
> index e813a37910af4..ee1e4bf613227 100644
> --- a/sound/soc/codecs/sgtl5000.c
> +++ b/sound/soc/codecs/sgtl5000.c
> @@ -1174,12 +1174,16 @@ static int sgtl5000_set_power_regs(struct snd_soc_component *component)
>                                         SGTL5000_INT_OSC_EN);
>                 /* Enable VDDC charge pump */
>                 ana_pwr |= SGTL5000_VDDC_CHRGPMP_POWERUP;
> -       } else if (vddio >= 3100 && vdda >= 3100) {
> +       } else {
>                 ana_pwr &= ~SGTL5000_VDDC_CHRGPMP_POWERUP;
> -               /* VDDC use VDDIO rail */
> -               lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
> -               lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
> -                           SGTL5000_VDDC_MAN_ASSN_SHIFT;
> +               /* if vddio == vdda the source of charge pump should be
> +                * assigned manually to VDDIO
> +                */
minor: please check the preferred style for long (multi-line) comments
in coding-style.rst,
first line should be empty.

> +               if (vddio == vdda) {
> +                       lreg_ctrl |= SGTL5000_VDDC_ASSN_OVRD;
> +                       lreg_ctrl |= SGTL5000_VDDC_MAN_ASSN_VDDIO <<
> +                                   SGTL5000_VDDC_MAN_ASSN_SHIFT;
> +               }
>         }
>
>         snd_soc_component_write(component, SGTL5000_CHIP_LINREG_CTRL, lreg_ctrl);
> --
> 2.20.1
>

With my comments addressed:
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)

Re: [PATCH v2 3/6] ASoC: sgtl5000: Fix of unmute outputs on probe

[Igor Opaniuk]

On Tue, Jun 25, 2019 at 10:54 AM Oleksandr Suvorov
<oleksandr.suvorov@toradex.com> wrote:
>
> To enable "zero cross detect" for ADC/HP, change
> HP_ZCD_EN/ADC_ZCD_EN bits only instead of writing the whole
> CHIP_ANA_CTRL register.
>
> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
>
>  sound/soc/codecs/sgtl5000.c | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/sound/soc/codecs/sgtl5000.c b/sound/soc/codecs/sgtl5000.c
> index bb58c997c6914..e813a37910af4 100644
> --- a/sound/soc/codecs/sgtl5000.c
> +++ b/sound/soc/codecs/sgtl5000.c
> @@ -1289,6 +1289,7 @@ static int sgtl5000_probe(struct snd_soc_component *component)
>         int ret;
>         u16 reg;
>         struct sgtl5000_priv *sgtl5000 = snd_soc_component_get_drvdata(component);
> +       unsigned int zcd_mask = SGTL5000_HP_ZCD_EN | SGTL5000_ADC_ZCD_EN;
>
>         /* power up sgtl5000 */
>         ret = sgtl5000_set_power_regs(component);
> @@ -1316,9 +1317,8 @@ static int sgtl5000_probe(struct snd_soc_component *component)
>                0x1f);
>         snd_soc_component_write(component, SGTL5000_CHIP_PAD_STRENGTH, reg);
>
> -       snd_soc_component_write(component, SGTL5000_CHIP_ANA_CTRL,
> -                       SGTL5000_HP_ZCD_EN |
> -                       SGTL5000_ADC_ZCD_EN);
> +       snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
> +               zcd_mask, zcd_mask);
>
>         snd_soc_component_update_bits(component, SGTL5000_CHIP_MIC_CTRL,
>                         SGTL5000_BIAS_R_MASK,
> --
> 2.20.1
>

Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)

Re: [PATCH v2 5/6] ASoC: Define a set of DAPM pre/post-up events

[Igor Opaniuk]

On Tue, Jun 25, 2019 at 10:55 AM Oleksandr Suvorov
<oleksandr.suvorov@toradex.com> wrote:
>
> Prepare to use SND_SOC_DAPM_PRE_POST_PMU definition to
> reduce coming code size and make it more readable.
>
> Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
> ---
>
>  include/sound/soc-dapm.h | 2 ++
>  1 file changed, 2 insertions(+)
>
> diff --git a/include/sound/soc-dapm.h b/include/sound/soc-dapm.h
> index c00a0b8ade086..6c66941601307 100644
> --- a/include/sound/soc-dapm.h
> +++ b/include/sound/soc-dapm.h
> @@ -353,6 +353,8 @@ struct device;
>  #define SND_SOC_DAPM_WILL_PMD   0x80    /* called at start of sequence */
>  #define SND_SOC_DAPM_PRE_POST_PMD \
>                                 (SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMD)
> +#define SND_SOC_DAPM_PRE_POST_PMU \
> +                               (SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU)
>
>  /* convenience event type detection */
>  #define SND_SOC_DAPM_EVENT_ON(e)       \
> --
> 2.20.1
>

Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>

-- 
Best regards - Freundliche Grüsse - Meilleures salutations

Senior Development Engineer,
Igor Opaniuk

Toradex AG
Altsagenstrasse 5 | 6048 Horw/Luzern | Switzerland | T: +41 41 500 48
00 (main line)