From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1753294AbdCOUSX (ORCPT ); Wed, 15 Mar 2017 16:18:23 -0400 Received: from mail-ot0-f169.google.com ([74.125.82.169]:36797 "EHLO mail-ot0-f169.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751480AbdCOUSV (ORCPT ); Wed, 15 Mar 2017 16:18:21 -0400 MIME-Version: 1.0 In-Reply-To: <7f5ddeba-6f79-9de5-2c67-a77e6bec0ef9@broadcom.com> References: <1489590033-4946-1-git-send-email-npcomplete13@gmail.com> <20170315185214.GF21021@lunn.ch> <7f5ddeba-6f79-9de5-2c67-a77e6bec0ef9@broadcom.com> From: Vivek Unune Date: Wed, 15 Mar 2017 16:18:20 -0400 Message-ID: Subject: Re: [PATCH] ARM: dts: BCM5301X: Add support for Linksys EA9500 To: Florian Fainelli Cc: Andrew Lunn , hauke@hauke-m.de, zajec5@gmail.com, bcm-kernel-feedback-list@broadcom.com, robh+dt@kernel.org, mark.rutland@arm.com, linux@armlinux.org.uk, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Content-Type: text/plain; charset=UTF-8 Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Thanks Florian. Let me try this out. First I'll try to figure out how to add a mdio node. Over the weekend I was trying enable DSA driver, but did not see DSA under network. I'm using LEDE source with kernel 4.9. Nor did I see it when I tried 'make kernel_menuconfig' Thanks again. On Wed, Mar 15, 2017 at 3:49 PM, Florian Fainelli wrote: > On 03/15/2017 12:34 PM, Vivek Unune wrote: >> Andrew, >> >> I'm not entirely sure. But here is what I observed. >> >> Boot loader sets up both the switches. And I can use all 8 ports of the >> router when I boot Lede. Only the internal swich is detected and >> configurable via swconfig tool >> Internal switch is connected to CPU via port 5 same as Netgear R8000. >> The other bit here is that I looked through the GPL source and gpio pin >> 10 is labeled as EA9500_RST2LANSW_GPIO10_PIN/ResetSwitch. So when I >> performed a robo reset of the pin and 5 (labeled 1 thru 5 on the unit) >> of the 8 physical ports stopped working (no packets). >> >> If the external switch were to be connect via dedicated ethernet >> interface it should have shown up during the probe. Is in't it? > > Not necessarily, and probably not with LEDE which would treat the > external 53125 as a dumb switch and not even see it. With a mainline > kernel and the B53 DSA driver you would be able to represent both > switches in Device Tree and describe how they are cascading from each other. > > The potential Device Tree changes could look like this (based on your > explanation, but I am not sure) for your platform, assuming the 53125 is > actually exposing the front panel ports and that we did introduce a > "mdio" node which would be required to expose the external BCM53125 switch. > > > /* There is no MDIO node, there should be one */ > &mdio { > status = "okay"; > > switch@30 { > #address-cells = <1>; > #size-cells = <0>; > reset-gpios = <&gpio 10>; > reset-names = "robo_reset"; > > ports { > #address-cells = <1>; > #size-cells = <0>; > > port@0 { > reg = <0>; > label = "lan1"; > }; > > port@1 { > reg = <1>; > label = "lan2"; > }; > > port@2 { > reg = <2>; > label = "lan3"; > }; > > port@3 { > reg = <3>; > label = "lan1"; > }; > > port@4 { > reg = <4>; > label = "wan"; > }; > > port@5 { > reg = <5>; > label = "cpu"; > ethernet = <&sw0port8>; > fixed-link { > speed = <1000>; > full-duplex; > }; > }; > }; > }; > }; > > &srab { > status = "okay"; > > ports { > #address-cells = <1>; > #size-cells = <0>; > > port@5 { > reg = <5>; > label = "cpu"; > ethernet = <&gmac0>; > fixed-link { > speed = <1000>; > full-duplex; > }; > }; > > sw0port8: port@8 { > reg = <8>; > label = "extswitch"; > > fixed-link { > speed = <1000>; > full-duplex; > }; > }; > }; > }; > >> >> Thanks, >> >> Vivek >> >> >> On Wed, Mar 15, 2017 at 2:52 PM Andrew Lunn > > wrote: >> >> Hi Vivek >> >> > - It has two switches in order to support 8 lan ports. Internal >> switch is >> > BCM53012. The external switch BCM53125 currently works as "dumb >> switch" >> >> Do you know how the second switch is connected? Is it cascaded off the >> internal switch? Or does it have a dedicated Ethernet interface? >> >> Thanks >> Andrew >> > > > -- > Florian