[PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[Maxime Ripard]

Hi,

Here is an preliminary version of the MIPI-DSI support for the Allwinner
SoCs.

This controller can be found on a number of recent SoCs, such as the
A31, A33 or the A64.

Given the sparse documentation, there's a number of obscure areas, but
the current implementation has been tested with a 4-lanes DSI panel on
an A33.

The support is a bit rough around the edges at the time, and some artifacts
are still shown on the screen for some reasons. Wider testing with
different display will hopefully nail those down.

This needs the regmap_mmio_attach_clk, on its way to Linus in 4.17.

Let me know what you think,
Maxime

Changes from v3:
  - Rebased on top of current drm-misc-next
  - Switched to SPDX license header
  - Made the ECC array const
  - Split the big DSI patch into two, one to add the DSI driver and one to
    add the TCON bits.
  - Removed the dithering code
  - Changed the DT labels to remove the indices
  - Used sleeps instead of delays in the panel driver
  - Used the backlight_enable / _disable functions
  - Added Chen-Yu's Reviewed-by

Changes from v2:
  - Added a ports node under the DSI node
  - Changed the huarui panel driver to an ili9881c driver
  - Changed the panel vendor to bananapi
  - Made the init table static in the panel driver
  - Dropped the huarui vendor patch for the DT doc.

Changes from v1:
  - Rebased on 4.16-rc1
  - Constified a few function arguments and structures
  - Reworked the DT binding example a bit
  - Reworked the panel driver to check for DSI return codes, and use DCS
    helpers when possible

Maxime Ripard (8):
  drm/sun4i: tcon: Add TRI finish interrupt for vblank
  dt-bindings: display: Add Allwinner MIPI-DSI bindings
  drm/sun4i: Add Allwinner A31 MIPI-DSI controller support
  drm/sun4i: Tie the DSI controller in the TCON
  dt-bindings: panel: Add the Ilitek ILI9881c panel documentation
  drm/panel: Add Ilitek ILI9881c panel driver
  ARM: dts: sun8i: a33: Add the DSI-related nodes
  [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display

 Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt |   20 +-
 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt       |   93 ++++++-
 arch/arm/boot/dts/sun8i-a33.dtsi                                    |   44 +++-
 arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts                        |   39 +++-
 drivers/gpu/drm/panel/Kconfig                                       |    9 +-
 drivers/gpu/drm/panel/Makefile                                      |    1 +-
 drivers/gpu/drm/panel/panel-ilitek-ili9881c.c                       |  489 ++++++++++++++++++++++++++++++++-
 drivers/gpu/drm/sun4i/Kconfig                                       |   10 +-
 drivers/gpu/drm/sun4i/Makefile                                      |    4 +-
 drivers/gpu/drm/sun4i/sun4i_tcon.c                                  |   86 +++++-
 drivers/gpu/drm/sun4i/sun4i_tcon.h                                  |   46 +++-
 drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c                             |  292 +++++++++++++++++++-
 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c                              | 1107 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h                              |   63 ++++-
 14 files changed, 2300 insertions(+), 3 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt
 create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h

base-commit: 7d9cf386c8da2490d0ee55cedb87be94a9e6093a
-- 
git-series 0.9.1

[PATCH v4 1/8] drm/sun4i: tcon: Add TRI finish interrupt for vblank

[Maxime Ripard]

The "CPU" (or Intel 8080) interface uses a different interrupt called
TRI_FINISH (most likely TRI being for trigger) to notify the end of frames,
and hence the VBLANK period.

And that interrupt to the possible VBLANK interrupts source.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 drivers/gpu/drm/sun4i/sun4i_tcon.c |  9 ++++++---
 drivers/gpu/drm/sun4i/sun4i_tcon.h |  4 ++++
 2 files changed, 10 insertions(+), 3 deletions(-)

diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index c3d92d537240..5f423ed2f01b 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -201,7 +201,8 @@ void sun4i_tcon_enable_vblank(struct sun4i_tcon *tcon, bool enable)
 	DRM_DEBUG_DRIVER("%sabling VBLANK interrupt\n", enable ? "En" : "Dis");
 
 	mask = SUN4I_TCON_GINT0_VBLANK_ENABLE(0) |
-	       SUN4I_TCON_GINT0_VBLANK_ENABLE(1);
+		SUN4I_TCON_GINT0_VBLANK_ENABLE(1) |
+		SUN4I_TCON_GINT0_TCON0_TRI_FINISH_ENABLE;
 
 	if (enable)
 		val = mask;
@@ -582,7 +583,8 @@ static irqreturn_t sun4i_tcon_handler(int irq, void *private)
 	regmap_read(tcon->regs, SUN4I_TCON_GINT0_REG, &status);
 
 	if (!(status & (SUN4I_TCON_GINT0_VBLANK_INT(0) |
-			SUN4I_TCON_GINT0_VBLANK_INT(1))))
+			SUN4I_TCON_GINT0_VBLANK_INT(1) |
+			SUN4I_TCON_GINT0_TCON0_TRI_FINISH_INT)))
 		return IRQ_NONE;
 
 	drm_crtc_handle_vblank(&scrtc->crtc);
@@ -591,7 +593,8 @@ static irqreturn_t sun4i_tcon_handler(int irq, void *private)
 	/* Acknowledge the interrupt */
 	regmap_update_bits(tcon->regs, SUN4I_TCON_GINT0_REG,
 			   SUN4I_TCON_GINT0_VBLANK_INT(0) |
-			   SUN4I_TCON_GINT0_VBLANK_INT(1),
+			   SUN4I_TCON_GINT0_VBLANK_INT(1) |
+			   SUN4I_TCON_GINT0_TCON0_TRI_FINISH_INT,
 			   0);
 
 	if (engine->ops->vblank_quirk)
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.h b/drivers/gpu/drm/sun4i/sun4i_tcon.h
index 161e09427124..2e0fb9640ed9 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.h
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.h
@@ -28,7 +28,11 @@
 
 #define SUN4I_TCON_GINT0_REG			0x4
 #define SUN4I_TCON_GINT0_VBLANK_ENABLE(pipe)		BIT(31 - (pipe))
+#define SUN4I_TCON_GINT0_TCON0_TRI_FINISH_ENABLE	BIT(27)
+#define SUN4I_TCON_GINT0_TCON0_TRI_COUNTER_ENABLE	BIT(26)
 #define SUN4I_TCON_GINT0_VBLANK_INT(pipe)		BIT(15 - (pipe))
+#define SUN4I_TCON_GINT0_TCON0_TRI_FINISH_INT		BIT(11)
+#define SUN4I_TCON_GINT0_TCON0_TRI_COUNTER_INT		BIT(10)
 
 #define SUN4I_TCON_GINT1_REG			0x8
 #define SUN4I_TCON_FRM_CTL_REG			0x10
-- 
git-series 0.9.1

[PATCH v4 2/8] dt-bindings: display: Add Allwinner MIPI-DSI bindings

[Maxime Ripard]

The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 93 +++++++-
 1 file changed, 93 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt

diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
new file mode 100644
index 000000000000..6a6cf5de08b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
@@ -0,0 +1,93 @@
+Allwinner A31 DSI Encoder
+=========================
+
+The DSI pipeline consists of two separate blocks: the DSI controller
+itself, and its associated D-PHY.
+
+DSI Encoder
+-----------
+
+The DSI Encoder generates the DSI signal from the TCON's.
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun6i-a31-mipi-dsi
+  - reg: base address and size of memory-mapped region
+  - interrupts: interrupt associated to this IP
+  - clocks: phandles to the clocks feeding the DSI encoder
+    * bus: the DSI interface clock
+    * mod: the DSI module clock
+  - clock-names: the clock names mentioned above
+  - phys: phandle to the D-PHY
+  - phy-names: must be "dphy"
+  - resets: phandle to the reset controller driving the encoder
+
+  - ports: A ports node with endpoint definitions as defined in
+    Documentation/devicetree/bindings/media/video-interfaces.txt. The
+    first port should be the input endpoint, usually coming from the
+    associated TCON.
+
+Any MIPI-DSI device attached to this should be described according to
+the bindings defined in ../mipi-dsi-bus.txt
+
+D-PHY
+-----
+
+Required properties:
+  - compatible: value must be one of:
+    * allwinner,sun6i-a31-mipi-dphy
+  - reg: base address and size of memory-mapped region
+  - clocks: phandles to the clocks feeding the DSI encoder
+    * bus: the DSI interface clock
+    * mod: the DSI module clock
+  - clock-names: the clock names mentioned above
+  - resets: phandle to the reset controller driving the encoder
+
+Example:
+
+dsi0: dsi@1ca0000 {
+	compatible = "allwinner,sun6i-a31-mipi-dsi";
+	reg = <0x01ca0000 0x1000>;
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&ccu CLK_BUS_MIPI_DSI>,
+		 <&ccu CLK_DSI_SCLK>;
+	clock-names = "bus", "mod";
+	resets = <&ccu RST_BUS_MIPI_DSI>;
+	phys = <&dphy0>;
+	phy-names = "dphy";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	panel@0 {
+		compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+		reg = <0>;
+		power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
+		reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
+		backlight = <&pwm_bl>;
+	};
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			dsi0_in_tcon0: endpoint {
+				remote-endpoint = <&tcon0_out_dsi0>;
+			};
+		};
+	};
+};
+
+dphy0: d-phy@1ca1000 {
+	compatible = "allwinner,sun6i-a31-mipi-dphy";
+	reg = <0x01ca1000 0x1000>;
+	clocks = <&ccu CLK_BUS_MIPI_DSI>,
+		 <&ccu CLK_DSI_DPHY>;
+	clock-names = "bus", "mod";
+	resets = <&ccu RST_BUS_MIPI_DSI>;
+	#phy-cells = <0>;
+};
-- 
git-series 0.9.1

[PATCH v4 3/8] drm/sun4i: Add Allwinner A31 MIPI-DSI controller support

[Maxime Ripard]

Most of the Allwinner SoCs since the A31 share the same MIPI-DSI
controller.

While that controller is mostly undocumented, the code is out there and has
been cleaned up in order to be integrated into DRM. However, there's still
some dark areas that are a bit unclear about how the block exactly
operates.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 drivers/gpu/drm/sun4i/Kconfig           |   10 +-
 drivers/gpu/drm/sun4i/Makefile          |    4 +-
 drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c |  292 ++++++-
 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c  | 1107 ++++++++++++++++++++++++-
 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h  |   63 +-
 5 files changed, 1476 insertions(+)
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
 create mode 100644 drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h

diff --git a/drivers/gpu/drm/sun4i/Kconfig b/drivers/gpu/drm/sun4i/Kconfig
index eee6bc0eaf97..156a865c3e6d 100644
--- a/drivers/gpu/drm/sun4i/Kconfig
+++ b/drivers/gpu/drm/sun4i/Kconfig
@@ -40,6 +40,16 @@ config DRM_SUN4I_BACKEND
 	  do some alpha blending and feed graphics to TCON. If M is
 	  selected the module will be called sun4i-backend.
 
+config DRM_SUN6I_DSI
+	tristate "Allwinner A31 MIPI-DSI Controller Support"
+	default MACH_SUN8I
+	select CRC_CCITT
+	select DRM_MIPI_DSI
+	help
+	  Choose this option if you want have an Allwinner SoC with
+	  MIPI-DSI support. If M is selected the module will be called
+	  sun6i-dsi
+
 config DRM_SUN8I_DW_HDMI
 	tristate "Support for Allwinner version of DesignWare HDMI"
 	depends on DRM_SUN4I
diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
index 330843ce4280..2589f4acd5ae 100644
--- a/drivers/gpu/drm/sun4i/Makefile
+++ b/drivers/gpu/drm/sun4i/Makefile
@@ -24,6 +24,9 @@ sun4i-tcon-y			+= sun4i_lvds.o
 sun4i-tcon-y			+= sun4i_tcon.o
 sun4i-tcon-y			+= sun4i_rgb.o
 
+sun6i-dsi-y			+= sun6i_mipi_dphy.o
+sun6i-dsi-y			+= sun6i_mipi_dsi.o
+
 obj-$(CONFIG_DRM_SUN4I)		+= sun4i-drm.o
 obj-$(CONFIG_DRM_SUN4I)		+= sun4i-tcon.o
 obj-$(CONFIG_DRM_SUN4I)		+= sun4i_tv.o
@@ -31,5 +34,6 @@ obj-$(CONFIG_DRM_SUN4I)		+= sun6i_drc.o
 
 obj-$(CONFIG_DRM_SUN4I_BACKEND)	+= sun4i-backend.o sun4i-frontend.o
 obj-$(CONFIG_DRM_SUN4I_HDMI)	+= sun4i-drm-hdmi.o
+obj-$(CONFIG_DRM_SUN6I_DSI)	+= sun6i-dsi.o
 obj-$(CONFIG_DRM_SUN8I_DW_HDMI)	+= sun8i-drm-hdmi.o
 obj-$(CONFIG_DRM_SUN8I_MIXER)	+= sun8i-mixer.o
diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c
new file mode 100644
index 000000000000..e4d19431fa0e
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dphy.c
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2016 Allwinnertech Co., Ltd.
+ * Copyright (C) 2017-2018 Bootlin
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include "sun6i_mipi_dsi.h"
+
+#define SUN6I_DPHY_GCTL_REG		0x00
+#define SUN6I_DPHY_GCTL_LANE_NUM(n)		((((n) - 1) & 3) << 4)
+#define SUN6I_DPHY_GCTL_EN			BIT(0)
+
+#define SUN6I_DPHY_TX_CTL_REG		0x04
+#define SUN6I_DPHY_TX_CTL_HS_TX_CLK_CONT	BIT(28)
+
+#define SUN6I_DPHY_TX_TIME0_REG		0x10
+#define SUN6I_DPHY_TX_TIME0_HS_TRAIL(n)		(((n) & 0xff) << 24)
+#define SUN6I_DPHY_TX_TIME0_HS_PREPARE(n)	(((n) & 0xff) << 16)
+#define SUN6I_DPHY_TX_TIME0_LP_CLK_DIV(n)	((n) & 0xff)
+
+#define SUN6I_DPHY_TX_TIME1_REG		0x14
+#define SUN6I_DPHY_TX_TIME1_CLK_POST(n)		(((n) & 0xff) << 24)
+#define SUN6I_DPHY_TX_TIME1_CLK_PRE(n)		(((n) & 0xff) << 16)
+#define SUN6I_DPHY_TX_TIME1_CLK_ZERO(n)		(((n) & 0xff) << 8)
+#define SUN6I_DPHY_TX_TIME1_CLK_PREPARE(n)	((n) & 0xff)
+
+#define SUN6I_DPHY_TX_TIME2_REG		0x18
+#define SUN6I_DPHY_TX_TIME2_CLK_TRAIL(n)	((n) & 0xff)
+
+#define SUN6I_DPHY_TX_TIME3_REG		0x1c
+
+#define SUN6I_DPHY_TX_TIME4_REG		0x20
+#define SUN6I_DPHY_TX_TIME4_HS_TX_ANA1(n)	(((n) & 0xff) << 8)
+#define SUN6I_DPHY_TX_TIME4_HS_TX_ANA0(n)	((n) & 0xff)
+
+#define SUN6I_DPHY_ANA0_REG		0x4c
+#define SUN6I_DPHY_ANA0_REG_PWS			BIT(31)
+#define SUN6I_DPHY_ANA0_REG_DMPC		BIT(28)
+#define SUN6I_DPHY_ANA0_REG_DMPD(n)		(((n) & 0xf) << 24)
+#define SUN6I_DPHY_ANA0_REG_SLV(n)		(((n) & 7) << 12)
+#define SUN6I_DPHY_ANA0_REG_DEN(n)		(((n) & 0xf) << 8)
+
+#define SUN6I_DPHY_ANA1_REG		0x50
+#define SUN6I_DPHY_ANA1_REG_VTTMODE		BIT(31)
+#define SUN6I_DPHY_ANA1_REG_CSMPS(n)		(((n) & 3) << 28)
+#define SUN6I_DPHY_ANA1_REG_SVTT(n)		(((n) & 0xf) << 24)
+
+#define SUN6I_DPHY_ANA2_REG		0x54
+#define SUN6I_DPHY_ANA2_EN_P2S_CPU(n)		(((n) & 0xf) << 24)
+#define SUN6I_DPHY_ANA2_EN_P2S_CPU_MASK		GENMASK(27, 24)
+#define SUN6I_DPHY_ANA2_EN_CK_CPU		BIT(4)
+#define SUN6I_DPHY_ANA2_REG_ENIB		BIT(1)
+
+#define SUN6I_DPHY_ANA3_REG		0x58
+#define SUN6I_DPHY_ANA3_EN_VTTD(n)		(((n) & 0xf) << 28)
+#define SUN6I_DPHY_ANA3_EN_VTTD_MASK		GENMASK(31, 28)
+#define SUN6I_DPHY_ANA3_EN_VTTC			BIT(27)
+#define SUN6I_DPHY_ANA3_EN_DIV			BIT(26)
+#define SUN6I_DPHY_ANA3_EN_LDOC			BIT(25)
+#define SUN6I_DPHY_ANA3_EN_LDOD			BIT(24)
+#define SUN6I_DPHY_ANA3_EN_LDOR			BIT(18)
+
+#define SUN6I_DPHY_ANA4_REG		0x5c
+#define SUN6I_DPHY_ANA4_REG_DMPLVC		BIT(24)
+#define SUN6I_DPHY_ANA4_REG_DMPLVD(n)		(((n) & 0xf) << 20)
+#define SUN6I_DPHY_ANA4_REG_CKDV(n)		(((n) & 0x1f) << 12)
+#define SUN6I_DPHY_ANA4_REG_TMSC(n)		(((n) & 3) << 10)
+#define SUN6I_DPHY_ANA4_REG_TMSD(n)		(((n) & 3) << 8)
+#define SUN6I_DPHY_ANA4_REG_TXDNSC(n)		(((n) & 3) << 6)
+#define SUN6I_DPHY_ANA4_REG_TXDNSD(n)		(((n) & 3) << 4)
+#define SUN6I_DPHY_ANA4_REG_TXPUSC(n)		(((n) & 3) << 2)
+#define SUN6I_DPHY_ANA4_REG_TXPUSD(n)		((n) & 3)
+
+#define SUN6I_DPHY_DBG5_REG		0xf4
+
+int sun6i_dphy_init(struct sun6i_dphy *dphy, unsigned int lanes)
+{
+	reset_control_deassert(dphy->reset);
+	clk_prepare_enable(dphy->mod_clk);
+	clk_set_rate_exclusive(dphy->mod_clk, 150000000);
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_CTL_REG,
+		     SUN6I_DPHY_TX_CTL_HS_TX_CLK_CONT);
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_TIME0_REG,
+		     SUN6I_DPHY_TX_TIME0_LP_CLK_DIV(14) |
+		     SUN6I_DPHY_TX_TIME0_HS_PREPARE(6) |
+		     SUN6I_DPHY_TX_TIME0_HS_TRAIL(10));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_TIME1_REG,
+		     SUN6I_DPHY_TX_TIME1_CLK_PREPARE(7) |
+		     SUN6I_DPHY_TX_TIME1_CLK_ZERO(50) |
+		     SUN6I_DPHY_TX_TIME1_CLK_PRE(3) |
+		     SUN6I_DPHY_TX_TIME1_CLK_POST(10));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_TIME2_REG,
+		     SUN6I_DPHY_TX_TIME2_CLK_TRAIL(30));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_TIME3_REG, 0);
+
+	regmap_write(dphy->regs, SUN6I_DPHY_TX_TIME4_REG,
+		     SUN6I_DPHY_TX_TIME4_HS_TX_ANA0(3) |
+		     SUN6I_DPHY_TX_TIME4_HS_TX_ANA1(3));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_GCTL_REG,
+		     SUN6I_DPHY_GCTL_LANE_NUM(lanes) |
+		     SUN6I_DPHY_GCTL_EN);
+
+	return 0;
+}
+
+int sun6i_dphy_power_on(struct sun6i_dphy *dphy, unsigned int lanes)
+{
+	u8 lanes_mask = GENMASK(lanes - 1, 0);
+
+	regmap_write(dphy->regs, SUN6I_DPHY_ANA0_REG,
+		     SUN6I_DPHY_ANA0_REG_PWS |
+		     SUN6I_DPHY_ANA0_REG_DMPC |
+		     SUN6I_DPHY_ANA0_REG_SLV(7) |
+		     SUN6I_DPHY_ANA0_REG_DMPD(lanes_mask) |
+		     SUN6I_DPHY_ANA0_REG_DEN(lanes_mask));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_ANA1_REG,
+		     SUN6I_DPHY_ANA1_REG_CSMPS(1) |
+		     SUN6I_DPHY_ANA1_REG_SVTT(7));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_ANA4_REG,
+		     SUN6I_DPHY_ANA4_REG_CKDV(1) |
+		     SUN6I_DPHY_ANA4_REG_TMSC(1) |
+		     SUN6I_DPHY_ANA4_REG_TMSD(1) |
+		     SUN6I_DPHY_ANA4_REG_TXDNSC(1) |
+		     SUN6I_DPHY_ANA4_REG_TXDNSD(1) |
+		     SUN6I_DPHY_ANA4_REG_TXPUSC(1) |
+		     SUN6I_DPHY_ANA4_REG_TXPUSD(1) |
+		     SUN6I_DPHY_ANA4_REG_DMPLVC |
+		     SUN6I_DPHY_ANA4_REG_DMPLVD(lanes_mask));
+
+	regmap_write(dphy->regs, SUN6I_DPHY_ANA2_REG,
+		     SUN6I_DPHY_ANA2_REG_ENIB);
+	udelay(5);
+
+	regmap_write(dphy->regs, SUN6I_DPHY_ANA3_REG,
+		     SUN6I_DPHY_ANA3_EN_LDOR |
+		     SUN6I_DPHY_ANA3_EN_LDOC |
+		     SUN6I_DPHY_ANA3_EN_LDOD);
+	udelay(1);
+
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA3_REG,
+			   SUN6I_DPHY_ANA3_EN_VTTC |
+			   SUN6I_DPHY_ANA3_EN_VTTD_MASK,
+			   SUN6I_DPHY_ANA3_EN_VTTC |
+			   SUN6I_DPHY_ANA3_EN_VTTD(lanes_mask));
+	udelay(1);
+
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA3_REG,
+			   SUN6I_DPHY_ANA3_EN_DIV,
+			   SUN6I_DPHY_ANA3_EN_DIV);
+	udelay(1);
+
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA2_REG,
+			   SUN6I_DPHY_ANA2_EN_CK_CPU,
+			   SUN6I_DPHY_ANA2_EN_CK_CPU);
+	udelay(1);
+
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA1_REG,
+			   SUN6I_DPHY_ANA1_REG_VTTMODE,
+			   SUN6I_DPHY_ANA1_REG_VTTMODE);
+
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA2_REG,
+			   SUN6I_DPHY_ANA2_EN_P2S_CPU_MASK,
+			   SUN6I_DPHY_ANA2_EN_P2S_CPU(lanes_mask));
+
+	return 0;
+}
+
+int sun6i_dphy_power_off(struct sun6i_dphy *dphy)
+{
+	regmap_update_bits(dphy->regs, SUN6I_DPHY_ANA1_REG,
+			   SUN6I_DPHY_ANA1_REG_VTTMODE, 0);
+
+	return 0;
+}
+
+int sun6i_dphy_exit(struct sun6i_dphy *dphy)
+{
+	clk_rate_exclusive_put(dphy->mod_clk);
+	clk_disable_unprepare(dphy->mod_clk);
+	reset_control_assert(dphy->reset);
+
+	return 0;
+}
+
+static struct regmap_config sun6i_dphy_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+	.max_register	= SUN6I_DPHY_DBG5_REG,
+	.name		= "mipi-dphy",
+};
+
+static const struct of_device_id sun6i_dphy_of_table[] = {
+	{ .compatible = "allwinner,sun6i-a31-mipi-dphy" },
+	{ }
+};
+
+int sun6i_dphy_probe(struct sun6i_dsi *dsi, struct device_node *node)
+{
+	struct sun6i_dphy *dphy;
+	struct resource res;
+	void __iomem *regs;
+	int ret;
+
+	if (!of_match_node(sun6i_dphy_of_table, node)) {
+		dev_err(dsi->dev, "Incompatible D-PHY\n");
+		return -EINVAL;
+	}
+
+	dphy = devm_kzalloc(dsi->dev, sizeof(*dphy), GFP_KERNEL);
+	if (!dphy)
+		return -ENOMEM;
+
+	ret = of_address_to_resource(node, 0, &res);
+	if (ret) {
+		dev_err(dsi->dev, "phy: Couldn't get our resources\n");
+		return ret;
+	}
+
+	regs = devm_ioremap_resource(dsi->dev, &res);
+	if (IS_ERR(regs)) {
+		dev_err(dsi->dev, "Couldn't map the DPHY encoder registers\n");
+		return PTR_ERR(regs);
+	}
+
+	dphy->regs = devm_regmap_init_mmio(dsi->dev, regs,
+					   &sun6i_dphy_regmap_config);
+	if (IS_ERR(dphy->regs)) {
+		dev_err(dsi->dev, "Couldn't create the DPHY encoder regmap\n");
+		return PTR_ERR(dphy->regs);
+	}
+
+	dphy->reset = of_reset_control_get_shared(node, NULL);
+	if (IS_ERR(dphy->reset)) {
+		dev_err(dsi->dev, "Couldn't get our reset line\n");
+		return PTR_ERR(dphy->reset);
+	}
+
+	dphy->bus_clk = of_clk_get_by_name(node, "bus");
+	if (IS_ERR(dphy->bus_clk)) {
+		dev_err(dsi->dev, "Couldn't get the DPHY bus clock\n");
+		ret = PTR_ERR(dphy->bus_clk);
+		goto err_free_reset;
+	}
+	regmap_mmio_attach_clk(dphy->regs, dphy->bus_clk);
+
+	dphy->mod_clk = of_clk_get_by_name(node, "mod");
+	if (IS_ERR(dphy->mod_clk)) {
+		dev_err(dsi->dev, "Couldn't get the DPHY mod clock\n");
+		ret = PTR_ERR(dphy->mod_clk);
+		goto err_free_bus;
+	}
+
+	dsi->dphy = dphy;
+
+	return 0;
+
+err_free_bus:
+	regmap_mmio_detach_clk(dphy->regs);
+	clk_put(dphy->bus_clk);
+err_free_reset:
+	reset_control_put(dphy->reset);
+	return ret;
+}
+
+int sun6i_dphy_remove(struct sun6i_dsi *dsi)
+{
+	struct sun6i_dphy *dphy = dsi->dphy;
+
+	regmap_mmio_detach_clk(dphy->regs);
+	clk_put(dphy->mod_clk);
+	clk_put(dphy->bus_clk);
+	reset_control_put(dphy->reset);
+
+	return 0;
+}
diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
new file mode 100644
index 000000000000..bfbf761f0c1d
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.c
@@ -0,0 +1,1107 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2016 Allwinnertech Co., Ltd.
+ * Copyright (C) 2017-2018 Bootlin
+ *
+ * Maxime Ripard <maxime.ripard@bootlin.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/component.h>
+#include <linux/crc-ccitt.h>
+#include <linux/of_address.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <linux/phy/phy.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+
+#include "sun4i_drv.h"
+#include "sun6i_mipi_dsi.h"
+
+#include <video/mipi_display.h>
+
+#define SUN6I_DSI_CTL_REG		0x000
+#define SUN6I_DSI_CTL_EN			BIT(0)
+
+#define SUN6I_DSI_BASIC_CTL_REG		0x00c
+#define SUN6I_DSI_BASIC_CTL_HBP_DIS		BIT(2)
+#define SUN6I_DSI_BASIC_CTL_HSA_HSE_DIS		BIT(1)
+#define SUN6I_DSI_BASIC_CTL_VIDEO_BURST		BIT(0)
+
+#define SUN6I_DSI_BASIC_CTL0_REG	0x010
+#define SUN6I_DSI_BASIC_CTL0_HS_EOTP_EN		BIT(18)
+#define SUN6I_DSI_BASIC_CTL0_CRC_EN		BIT(17)
+#define SUN6I_DSI_BASIC_CTL0_ECC_EN		BIT(16)
+#define SUN6I_DSI_BASIC_CTL0_INST_ST		BIT(0)
+
+#define SUN6I_DSI_BASIC_CTL1_REG	0x014
+#define SUN6I_DSI_BASIC_CTL1_VIDEO_ST_DELAY(n)	(((n) & 0x1fff) << 4)
+#define SUN6I_DSI_BASIC_CTL1_VIDEO_FILL		BIT(2)
+#define SUN6I_DSI_BASIC_CTL1_VIDEO_PRECISION	BIT(1)
+#define SUN6I_DSI_BASIC_CTL1_VIDEO_MODE		BIT(0)
+
+#define SUN6I_DSI_BASIC_SIZE0_REG	0x018
+#define SUN6I_DSI_BASIC_SIZE0_VBP(n)		(((n) & 0xfff) << 16)
+#define SUN6I_DSI_BASIC_SIZE0_VSA(n)		((n) & 0xfff)
+
+#define SUN6I_DSI_BASIC_SIZE1_REG	0x01c
+#define SUN6I_DSI_BASIC_SIZE1_VT(n)		(((n) & 0xfff) << 16)
+#define SUN6I_DSI_BASIC_SIZE1_VACT(n)		((n) & 0xfff)
+
+#define SUN6I_DSI_INST_FUNC_REG(n)	(0x020 + (n) * 0x04)
+#define SUN6I_DSI_INST_FUNC_INST_MODE(n)	(((n) & 0xf) << 28)
+#define SUN6I_DSI_INST_FUNC_ESCAPE_ENTRY(n)	(((n) & 0xf) << 24)
+#define SUN6I_DSI_INST_FUNC_TRANS_PACKET(n)	(((n) & 0xf) << 20)
+#define SUN6I_DSI_INST_FUNC_LANE_CEN		BIT(4)
+#define SUN6I_DSI_INST_FUNC_LANE_DEN(n)		((n) & 0xf)
+
+#define SUN6I_DSI_INST_LOOP_SEL_REG	0x040
+
+#define SUN6I_DSI_INST_LOOP_NUM_REG(n)	(0x044 + (n) * 0x10)
+#define SUN6I_DSI_INST_LOOP_NUM_N1(n)		(((n) & 0xfff) << 16)
+#define SUN6I_DSI_INST_LOOP_NUM_N0(n)		((n) & 0xfff)
+
+#define SUN6I_DSI_INST_JUMP_SEL_REG	0x048
+
+#define SUN6I_DSI_INST_JUMP_CFG_REG(n)	(0x04c + (n) * 0x04)
+#define SUN6I_DSI_INST_JUMP_CFG_TO(n)		(((n) & 0xf) << 20)
+#define SUN6I_DSI_INST_JUMP_CFG_POINT(n)	(((n) & 0xf) << 16)
+#define SUN6I_DSI_INST_JUMP_CFG_NUM(n)		((n) & 0xffff)
+
+#define SUN6I_DSI_TRANS_START_REG	0x060
+
+#define SUN6I_DSI_TRANS_ZERO_REG	0x078
+
+#define SUN6I_DSI_TCON_DRQ_REG		0x07c
+#define SUN6I_DSI_TCON_DRQ_ENABLE_MODE		BIT(28)
+#define SUN6I_DSI_TCON_DRQ_SET(n)		((n) & 0x3ff)
+
+#define SUN6I_DSI_PIXEL_CTL0_REG	0x080
+#define SUN6I_DSI_PIXEL_CTL0_PD_PLUG_DISABLE	BIT(16)
+#define SUN6I_DSI_PIXEL_CTL0_FORMAT(n)		((n) & 0xf)
+
+#define SUN6I_DSI_PIXEL_CTL1_REG	0x084
+
+#define SUN6I_DSI_PIXEL_PH_REG		0x090
+#define SUN6I_DSI_PIXEL_PH_ECC(n)		(((n) & 0xff) << 24)
+#define SUN6I_DSI_PIXEL_PH_WC(n)		(((n) & 0xffff) << 8)
+#define SUN6I_DSI_PIXEL_PH_VC(n)		(((n) & 3) << 6)
+#define SUN6I_DSI_PIXEL_PH_DT(n)		((n) & 0x3f)
+
+#define SUN6I_DSI_PIXEL_PF0_REG		0x098
+#define SUN6I_DSI_PIXEL_PF0_CRC_FORCE(n)	((n) & 0xffff)
+
+#define SUN6I_DSI_PIXEL_PF1_REG		0x09c
+#define SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINEN(n)	(((n) & 0xffff) << 16)
+#define SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINE0(n)	((n) & 0xffff)
+
+#define SUN6I_DSI_SYNC_HSS_REG		0x0b0
+
+#define SUN6I_DSI_SYNC_HSE_REG		0x0b4
+
+#define SUN6I_DSI_SYNC_VSS_REG		0x0b8
+
+#define SUN6I_DSI_SYNC_VSE_REG		0x0bc
+
+#define SUN6I_DSI_BLK_HSA0_REG		0x0c0
+
+#define SUN6I_DSI_BLK_HSA1_REG		0x0c4
+#define SUN6I_DSI_BLK_PF(n)			(((n) & 0xffff) << 16)
+#define SUN6I_DSI_BLK_PD(n)			((n) & 0xff)
+
+#define SUN6I_DSI_BLK_HBP0_REG		0x0c8
+
+#define SUN6I_DSI_BLK_HBP1_REG		0x0cc
+
+#define SUN6I_DSI_BLK_HFP0_REG		0x0d0
+
+#define SUN6I_DSI_BLK_HFP1_REG		0x0d4
+
+#define SUN6I_DSI_BLK_HBLK0_REG		0x0e0
+
+#define SUN6I_DSI_BLK_HBLK1_REG		0x0e4
+
+#define SUN6I_DSI_BLK_VBLK0_REG		0x0e8
+
+#define SUN6I_DSI_BLK_VBLK1_REG		0x0ec
+
+#define SUN6I_DSI_BURST_LINE_REG	0x0f0
+#define SUN6I_DSI_BURST_LINE_SYNC_POINT(n)	(((n) & 0xffff) << 16)
+#define SUN6I_DSI_BURST_LINE_NUM(n)		((n) & 0xffff)
+
+#define SUN6I_DSI_BURST_DRQ_REG		0x0f4
+#define SUN6I_DSI_BURST_DRQ_EDGE1(n)		(((n) & 0xffff) << 16)
+#define SUN6I_DSI_BURST_DRQ_EDGE0(n)		((n) & 0xffff)
+
+#define SUN6I_DSI_CMD_CTL_REG		0x200
+#define SUN6I_DSI_CMD_CTL_RX_OVERFLOW		BIT(26)
+#define SUN6I_DSI_CMD_CTL_RX_FLAG		BIT(25)
+#define SUN6I_DSI_CMD_CTL_TX_FLAG		BIT(9)
+
+#define SUN6I_DSI_CMD_RX_REG(n)		(0x240 + (n) * 0x04)
+
+#define SUN6I_DSI_DEBUG_DATA_REG	0x2f8
+
+#define SUN6I_DSI_CMD_TX_REG(n)		(0x300 + (n) * 0x04)
+
+enum sun6i_dsi_start_inst {
+	DSI_START_LPRX,
+	DSI_START_LPTX,
+	DSI_START_HSC,
+	DSI_START_HSD,
+};
+
+enum sun6i_dsi_inst_id {
+	DSI_INST_ID_LP11	= 0,
+	DSI_INST_ID_TBA,
+	DSI_INST_ID_HSC,
+	DSI_INST_ID_HSD,
+	DSI_INST_ID_LPDT,
+	DSI_INST_ID_HSCEXIT,
+	DSI_INST_ID_NOP,
+	DSI_INST_ID_DLY,
+	DSI_INST_ID_END		= 15,
+};
+
+enum sun6i_dsi_inst_mode {
+	DSI_INST_MODE_STOP	= 0,
+	DSI_INST_MODE_TBA,
+	DSI_INST_MODE_HS,
+	DSI_INST_MODE_ESCAPE,
+	DSI_INST_MODE_HSCEXIT,
+	DSI_INST_MODE_NOP,
+};
+
+enum sun6i_dsi_inst_escape {
+	DSI_INST_ESCA_LPDT	= 0,
+	DSI_INST_ESCA_ULPS,
+	DSI_INST_ESCA_UN1,
+	DSI_INST_ESCA_UN2,
+	DSI_INST_ESCA_RESET,
+	DSI_INST_ESCA_UN3,
+	DSI_INST_ESCA_UN4,
+	DSI_INST_ESCA_UN5,
+};
+
+enum sun6i_dsi_inst_packet {
+	DSI_INST_PACK_PIXEL	= 0,
+	DSI_INST_PACK_COMMAND,
+};
+
+static const u32 sun6i_dsi_ecc_array[] = {
+	[0] = (BIT(0) | BIT(1) | BIT(2) | BIT(4) | BIT(5) | BIT(7) | BIT(10) |
+	       BIT(11) | BIT(13) | BIT(16) | BIT(20) | BIT(21) | BIT(22) |
+	       BIT(23)),
+	[1] = (BIT(0) | BIT(1) | BIT(3) | BIT(4) | BIT(6) | BIT(8) | BIT(10) |
+	       BIT(12) | BIT(14) | BIT(17) | BIT(20) | BIT(21) | BIT(22) |
+	       BIT(23)),
+	[2] = (BIT(0) | BIT(2) | BIT(3) | BIT(5) | BIT(6) | BIT(9) | BIT(11) |
+	       BIT(12) | BIT(15) | BIT(18) | BIT(20) | BIT(21) | BIT(22)),
+	[3] = (BIT(1) | BIT(2) | BIT(3) | BIT(7) | BIT(8) | BIT(9) | BIT(13) |
+	       BIT(14) | BIT(15) | BIT(19) | BIT(20) | BIT(21) | BIT(23)),
+	[4] = (BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | BIT(16) |
+	       BIT(17) | BIT(18) | BIT(19) | BIT(20) | BIT(22) | BIT(23)),
+	[5] = (BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) |
+	       BIT(16) | BIT(17) | BIT(18) | BIT(19) | BIT(21) | BIT(22) |
+	       BIT(23)),
+};
+
+static u32 sun6i_dsi_ecc_compute(unsigned int data)
+{
+	int i;
+	u8 ecc = 0;
+
+	for (i = 0; i < ARRAY_SIZE(sun6i_dsi_ecc_array); i++) {
+		u32 field = sun6i_dsi_ecc_array[i];
+		bool init = false;
+		u8 val = 0;
+		int j;
+
+		for (j = 0; j < 24; j++) {
+			if (!(BIT(j) & field))
+				continue;
+
+			if (!init) {
+				val = (BIT(j) & data) ? 1 : 0;
+				init = true;
+			} else {
+				val ^= (BIT(j) & data) ? 1 : 0;
+			}
+		}
+
+		ecc |= val << i;
+	}
+
+	return ecc;
+}
+
+static u16 sun6i_dsi_crc_compute(u8 const *buffer, size_t len)
+{
+	return crc_ccitt(0xffff, buffer, len);
+}
+
+static u16 sun6i_dsi_crc_repeat_compute(u8 pd, size_t len)
+{
+	u8 buffer[len];
+
+	memset(buffer, pd, len);
+
+	return sun6i_dsi_crc_compute(buffer, len);
+}
+
+static u32 sun6i_dsi_build_sync_pkt(u8 dt, u8 vc, u8 d0, u8 d1)
+{
+	u32 val = dt & 0x3f;
+
+	val |= (vc & 3) << 6;
+	val |= (d0 & 0xff) << 8;
+	val |= (d1 & 0xff) << 16;
+	val |= sun6i_dsi_ecc_compute(val) << 24;
+
+	return val;
+}
+
+static u32 sun6i_dsi_build_blk0_pkt(u8 vc, u16 wc)
+{
+	return sun6i_dsi_build_sync_pkt(MIPI_DSI_BLANKING_PACKET, vc,
+					wc & 0xff, wc >> 8);
+}
+
+static u32 sun6i_dsi_build_blk1_pkt(u16 pd, size_t len)
+{
+	u32 val = SUN6I_DSI_BLK_PD(pd);
+
+	return val | SUN6I_DSI_BLK_PF(sun6i_dsi_crc_repeat_compute(pd, len));
+}
+
+static void sun6i_dsi_inst_abort(struct sun6i_dsi *dsi)
+{
+	regmap_update_bits(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG,
+			   SUN6I_DSI_BASIC_CTL0_INST_ST, 0);
+}
+
+static void sun6i_dsi_inst_commit(struct sun6i_dsi *dsi)
+{
+	regmap_update_bits(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG,
+			   SUN6I_DSI_BASIC_CTL0_INST_ST,
+			   SUN6I_DSI_BASIC_CTL0_INST_ST);
+}
+
+static int sun6i_dsi_inst_wait_for_completion(struct sun6i_dsi *dsi)
+{
+	u32 val;
+
+	return regmap_read_poll_timeout(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG,
+					val,
+					!(val & SUN6I_DSI_BASIC_CTL0_INST_ST),
+					100, 5000);
+}
+
+static void sun6i_dsi_inst_setup(struct sun6i_dsi *dsi,
+				 enum sun6i_dsi_inst_id id,
+				 enum sun6i_dsi_inst_mode mode,
+				 bool clock, u8 data,
+				 enum sun6i_dsi_inst_packet packet,
+				 enum sun6i_dsi_inst_escape escape)
+{
+	regmap_write(dsi->regs, SUN6I_DSI_INST_FUNC_REG(id),
+		     SUN6I_DSI_INST_FUNC_INST_MODE(mode) |
+		     SUN6I_DSI_INST_FUNC_ESCAPE_ENTRY(escape) |
+		     SUN6I_DSI_INST_FUNC_TRANS_PACKET(packet) |
+		     (clock ? SUN6I_DSI_INST_FUNC_LANE_CEN : 0) |
+		     SUN6I_DSI_INST_FUNC_LANE_DEN(data));
+}
+
+static void sun6i_dsi_inst_init(struct sun6i_dsi *dsi,
+				struct mipi_dsi_device *device)
+{
+	u8 lanes_mask = GENMASK(device->lanes - 1, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_LP11, DSI_INST_MODE_STOP,
+			     true, lanes_mask, 0, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_TBA, DSI_INST_MODE_TBA,
+			     false, 1, 0, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSC, DSI_INST_MODE_HS,
+			     true, 0, DSI_INST_PACK_PIXEL, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSD, DSI_INST_MODE_HS,
+			     false, lanes_mask, DSI_INST_PACK_PIXEL, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_LPDT, DSI_INST_MODE_ESCAPE,
+			     false, 1, DSI_INST_PACK_COMMAND,
+			     DSI_INST_ESCA_LPDT);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSCEXIT, DSI_INST_MODE_HSCEXIT,
+			     true, 0, 0, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_NOP, DSI_INST_MODE_STOP,
+			     false, lanes_mask, 0, 0);
+
+	sun6i_dsi_inst_setup(dsi, DSI_INST_ID_DLY, DSI_INST_MODE_NOP,
+			     true, lanes_mask, 0, 0);
+
+	regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_CFG_REG(0),
+		     SUN6I_DSI_INST_JUMP_CFG_POINT(DSI_INST_ID_NOP) |
+		     SUN6I_DSI_INST_JUMP_CFG_TO(DSI_INST_ID_HSCEXIT) |
+		     SUN6I_DSI_INST_JUMP_CFG_NUM(1));
+};
+
+static u16 sun6i_dsi_get_video_start_delay(struct sun6i_dsi *dsi,
+					   struct drm_display_mode *mode)
+{
+	return mode->vtotal - (mode->vsync_end - mode->vdisplay) + 1;
+}
+
+static void sun6i_dsi_setup_burst(struct sun6i_dsi *dsi,
+				  struct drm_display_mode *mode)
+{
+	struct mipi_dsi_device *device = dsi->device;
+	u32 val = 0;
+
+	if ((mode->hsync_end - mode->hdisplay) > 20) {
+		/* Maaaaaagic */
+		u16 drq = (mode->hsync_end - mode->hdisplay) - 20;
+
+		drq *= mipi_dsi_pixel_format_to_bpp(device->format);
+		drq /= 32;
+
+		val = (SUN6I_DSI_TCON_DRQ_ENABLE_MODE |
+		       SUN6I_DSI_TCON_DRQ_SET(drq));
+	}
+
+	regmap_write(dsi->regs, SUN6I_DSI_TCON_DRQ_REG, val);
+}
+
+static void sun6i_dsi_setup_inst_loop(struct sun6i_dsi *dsi,
+				      struct drm_display_mode *mode)
+{
+	u16 delay = 50 - 1;
+
+	regmap_write(dsi->regs, SUN6I_DSI_INST_LOOP_NUM_REG(0),
+		     SUN6I_DSI_INST_LOOP_NUM_N0(50 - 1) |
+		     SUN6I_DSI_INST_LOOP_NUM_N1(delay));
+	regmap_write(dsi->regs, SUN6I_DSI_INST_LOOP_NUM_REG(1),
+		     SUN6I_DSI_INST_LOOP_NUM_N0(50 - 1) |
+		     SUN6I_DSI_INST_LOOP_NUM_N1(delay));
+}
+
+static void sun6i_dsi_setup_format(struct sun6i_dsi *dsi,
+				   struct drm_display_mode *mode)
+{
+	struct mipi_dsi_device *device = dsi->device;
+	u32 val = SUN6I_DSI_PIXEL_PH_VC(device->channel);
+	u8 dt, fmt;
+	u16 wc;
+
+	/*
+	 * TODO: The format defines are only valid in video mode and
+	 * change in command mode.
+	 */
+	switch (device->format) {
+	case MIPI_DSI_FMT_RGB888:
+		dt = MIPI_DSI_PACKED_PIXEL_STREAM_24;
+		fmt = 8;
+		break;
+	case MIPI_DSI_FMT_RGB666:
+		dt = MIPI_DSI_PIXEL_STREAM_3BYTE_18;
+		fmt = 9;
+		break;
+	case MIPI_DSI_FMT_RGB666_PACKED:
+		dt = MIPI_DSI_PACKED_PIXEL_STREAM_18;
+		fmt = 10;
+		break;
+	case MIPI_DSI_FMT_RGB565:
+		dt = MIPI_DSI_PACKED_PIXEL_STREAM_16;
+		fmt = 11;
+		break;
+	default:
+		return;
+	}
+	val |= SUN6I_DSI_PIXEL_PH_DT(dt);
+
+	wc = mode->hdisplay * mipi_dsi_pixel_format_to_bpp(device->format) / 8;
+	val |= SUN6I_DSI_PIXEL_PH_WC(wc);
+	val |= SUN6I_DSI_PIXEL_PH_ECC(sun6i_dsi_ecc_compute(val));
+
+	regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PH_REG, val);
+
+	regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PF0_REG,
+		     SUN6I_DSI_PIXEL_PF0_CRC_FORCE(0xffff));
+
+	regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PF1_REG,
+		     SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINE0(0xffff) |
+		     SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINEN(0xffff));
+
+	regmap_write(dsi->regs, SUN6I_DSI_PIXEL_CTL0_REG,
+		     SUN6I_DSI_PIXEL_CTL0_PD_PLUG_DISABLE |
+		     SUN6I_DSI_PIXEL_CTL0_FORMAT(fmt));
+}
+
+static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi,
+				    struct drm_display_mode *mode)
+{
+	struct mipi_dsi_device *device = dsi->device;
+	unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8;
+	u16 hbp, hfp, hsa, hblk, vblk;
+
+	regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL_REG, 0);
+
+	regmap_write(dsi->regs, SUN6I_DSI_SYNC_HSS_REG,
+		     sun6i_dsi_build_sync_pkt(MIPI_DSI_H_SYNC_START,
+					      device->channel,
+					      0, 0));
+
+	regmap_write(dsi->regs, SUN6I_DSI_SYNC_HSE_REG,
+		     sun6i_dsi_build_sync_pkt(MIPI_DSI_H_SYNC_END,
+					      device->channel,
+					      0, 0));
+
+	regmap_write(dsi->regs, SUN6I_DSI_SYNC_VSS_REG,
+		     sun6i_dsi_build_sync_pkt(MIPI_DSI_V_SYNC_START,
+					      device->channel,
+					      0, 0));
+
+	regmap_write(dsi->regs, SUN6I_DSI_SYNC_VSE_REG,
+		     sun6i_dsi_build_sync_pkt(MIPI_DSI_V_SYNC_END,
+					      device->channel,
+					      0, 0));
+
+	regmap_write(dsi->regs, SUN6I_DSI_BASIC_SIZE0_REG,
+		     SUN6I_DSI_BASIC_SIZE0_VSA(mode->vsync_end -
+					       mode->vsync_start) |
+		     SUN6I_DSI_BASIC_SIZE0_VBP(mode->vsync_start -
+					       mode->vdisplay));
+
+	regmap_write(dsi->regs, SUN6I_DSI_BASIC_SIZE1_REG,
+		     SUN6I_DSI_BASIC_SIZE1_VACT(mode->vdisplay) |
+		     SUN6I_DSI_BASIC_SIZE1_VT(mode->vtotal));
+
+	/*
+	 * A sync period is composed of a blanking packet (4 bytes +
+	 * payload + 2 bytes) and a sync event packet (4 bytes). Its
+	 * minimal size is therefore 10 bytes
+	 */
+#define HSA_PACKET_OVERHEAD	10
+	hsa = max((unsigned int)HSA_PACKET_OVERHEAD,
+		  (mode->hsync_end - mode->hsync_start) * Bpp - HSA_PACKET_OVERHEAD);
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HSA0_REG,
+		     sun6i_dsi_build_blk0_pkt(device->channel, hsa));
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HSA1_REG,
+		     sun6i_dsi_build_blk1_pkt(0, hsa));
+
+	/*
+	 * The backporch is set using a blanking packet (4 bytes +
+	 * payload + 2 bytes). Its minimal size is therefore 6 bytes
+	 */
+#define HBP_PACKET_OVERHEAD	6
+	hbp = max((unsigned int)HBP_PACKET_OVERHEAD,
+		  (mode->hsync_start - mode->hdisplay) * Bpp - HBP_PACKET_OVERHEAD);
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HBP0_REG,
+		     sun6i_dsi_build_blk0_pkt(device->channel, hbp));
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HBP1_REG,
+		     sun6i_dsi_build_blk1_pkt(0, hbp));
+
+	/*
+	 * The frontporch is set using a blanking packet (4 bytes +
+	 * payload + 2 bytes). Its minimal size is therefore 6 bytes
+	 */
+#define HFP_PACKET_OVERHEAD	6
+	hfp = max((unsigned int)HFP_PACKET_OVERHEAD,
+		  (mode->htotal - mode->hsync_end) * Bpp - HFP_PACKET_OVERHEAD);
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HFP0_REG,
+		     sun6i_dsi_build_blk0_pkt(device->channel, hfp));
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HFP1_REG,
+		     sun6i_dsi_build_blk1_pkt(0, hfp));
+
+	/*
+	 * hblk seems to be the line + porches length.
+	 */
+	hblk = mode->htotal * Bpp - hsa;
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HBLK0_REG,
+		     sun6i_dsi_build_blk0_pkt(device->channel, hblk));
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_HBLK1_REG,
+		     sun6i_dsi_build_blk1_pkt(0, hblk));
+
+	/*
+	 * And I'm not entirely sure what vblk is about. The driver in
+	 * Allwinner BSP is using a rather convoluted calculation
+	 * there only for 4 lanes. However, using 0 (the !4 lanes
+	 * case) even with a 4 lanes screen seems to work...
+	 */
+	vblk = 0;
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_VBLK0_REG,
+		     sun6i_dsi_build_blk0_pkt(device->channel, vblk));
+	regmap_write(dsi->regs, SUN6I_DSI_BLK_VBLK1_REG,
+		     sun6i_dsi_build_blk1_pkt(0, vblk));
+}
+
+static int sun6i_dsi_start(struct sun6i_dsi *dsi,
+			   enum sun6i_dsi_start_inst func)
+{
+	switch (func) {
+	case DSI_START_LPTX:
+		regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG,
+			     DSI_INST_ID_LPDT << (4 * DSI_INST_ID_LP11) |
+			     DSI_INST_ID_END  << (4 * DSI_INST_ID_LPDT));
+		break;
+	case DSI_START_LPRX:
+		regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG,
+			     DSI_INST_ID_LPDT << (4 * DSI_INST_ID_LP11) |
+			     DSI_INST_ID_DLY  << (4 * DSI_INST_ID_LPDT) |
+			     DSI_INST_ID_TBA  << (4 * DSI_INST_ID_DLY) |
+			     DSI_INST_ID_END  << (4 * DSI_INST_ID_TBA));
+		break;
+	case DSI_START_HSC:
+		regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG,
+			     DSI_INST_ID_HSC  << (4 * DSI_INST_ID_LP11) |
+			     DSI_INST_ID_END  << (4 * DSI_INST_ID_HSC));
+		break;
+	case DSI_START_HSD:
+		regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG,
+			     DSI_INST_ID_NOP  << (4 * DSI_INST_ID_LP11) |
+			     DSI_INST_ID_HSD  << (4 * DSI_INST_ID_NOP) |
+			     DSI_INST_ID_DLY  << (4 * DSI_INST_ID_HSD) |
+			     DSI_INST_ID_NOP  << (4 * DSI_INST_ID_DLY) |
+			     DSI_INST_ID_END  << (4 * DSI_INST_ID_HSCEXIT));
+		break;
+	default:
+		regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG,
+			     DSI_INST_ID_END  << (4 * DSI_INST_ID_LP11));
+		break;
+	}
+
+	sun6i_dsi_inst_abort(dsi);
+	sun6i_dsi_inst_commit(dsi);
+
+	if (func == DSI_START_HSC)
+		regmap_write_bits(dsi->regs,
+				  SUN6I_DSI_INST_FUNC_REG(DSI_INST_ID_LP11),
+				  SUN6I_DSI_INST_FUNC_LANE_CEN, 0);
+
+	return 0;
+}
+
+static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder)
+{
+	struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
+	struct sun6i_dsi *dsi = encoder_to_sun6i_dsi(encoder);
+	struct mipi_dsi_device *device = dsi->device;
+	u16 delay;
+
+	DRM_DEBUG_DRIVER("Enabling DSI output\n");
+
+	pm_runtime_get_sync(dsi->dev);
+
+	delay = sun6i_dsi_get_video_start_delay(dsi, mode);
+	regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL1_REG,
+		     SUN6I_DSI_BASIC_CTL1_VIDEO_ST_DELAY(delay) |
+		     SUN6I_DSI_BASIC_CTL1_VIDEO_FILL |
+		     SUN6I_DSI_BASIC_CTL1_VIDEO_PRECISION |
+		     SUN6I_DSI_BASIC_CTL1_VIDEO_MODE);
+
+	sun6i_dsi_setup_burst(dsi, mode);
+	sun6i_dsi_setup_inst_loop(dsi, mode);
+	sun6i_dsi_setup_format(dsi, mode);
+	sun6i_dsi_setup_timings(dsi, mode);
+
+	sun6i_dphy_init(dsi->dphy, device->lanes);
+	sun6i_dphy_power_on(dsi->dphy, device->lanes);
+
+	if (!IS_ERR(dsi->panel))
+		drm_panel_prepare(dsi->panel);
+
+	/*
+	 * FIXME: This should be moved after the switch to HS mode.
+	 *
+	 * Unfortunately, once in HS mode, it seems like we're not
+	 * able to send DCS commands anymore, which would prevent any
+	 * panel to send any DCS command as part as their enable
+	 * method, which is quite common.
+	 *
+	 * I haven't seen any artifact due to that sub-optimal
+	 * ordering on the panels I've tested it with, so I guess this
+	 * will do for now, until that IP is better understood.
+	 */
+	if (!IS_ERR(dsi->panel))
+		drm_panel_enable(dsi->panel);
+
+	sun6i_dsi_start(dsi, DSI_START_HSC);
+
+	udelay(1000);
+
+	sun6i_dsi_start(dsi, DSI_START_HSD);
+}
+
+static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder)
+{
+	struct sun6i_dsi *dsi = encoder_to_sun6i_dsi(encoder);
+
+	DRM_DEBUG_DRIVER("Disabling DSI output\n");
+
+	if (!IS_ERR(dsi->panel)) {
+		drm_panel_disable(dsi->panel);
+		drm_panel_unprepare(dsi->panel);
+	}
+
+	sun6i_dphy_power_off(dsi->dphy);
+	sun6i_dphy_exit(dsi->dphy);
+
+	pm_runtime_put(dsi->dev);
+}
+
+static int sun6i_dsi_get_modes(struct drm_connector *connector)
+{
+	struct sun6i_dsi *dsi = connector_to_sun6i_dsi(connector);
+
+	return drm_panel_get_modes(dsi->panel);
+}
+
+static struct drm_connector_helper_funcs sun6i_dsi_connector_helper_funcs = {
+	.get_modes	= sun6i_dsi_get_modes,
+};
+
+static enum drm_connector_status
+sun6i_dsi_connector_detect(struct drm_connector *connector, bool force)
+{
+	return connector_status_connected;
+}
+
+static const struct drm_connector_funcs sun6i_dsi_connector_funcs = {
+	.detect			= sun6i_dsi_connector_detect,
+	.fill_modes		= drm_helper_probe_single_connector_modes,
+	.destroy		= drm_connector_cleanup,
+	.reset			= drm_atomic_helper_connector_reset,
+	.atomic_duplicate_state	= drm_atomic_helper_connector_duplicate_state,
+	.atomic_destroy_state	= drm_atomic_helper_connector_destroy_state,
+};
+
+static const struct drm_encoder_helper_funcs sun6i_dsi_enc_helper_funcs = {
+	.disable	= sun6i_dsi_encoder_disable,
+	.enable		= sun6i_dsi_encoder_enable,
+};
+
+static const struct drm_encoder_funcs sun6i_dsi_enc_funcs = {
+	.destroy	= drm_encoder_cleanup,
+};
+
+static u32 sun6i_dsi_dcs_build_pkt_hdr(struct sun6i_dsi *dsi,
+				       const struct mipi_dsi_msg *msg)
+{
+	u32 pkt = msg->type;
+
+	if (msg->type == MIPI_DSI_DCS_LONG_WRITE) {
+		pkt |= ((msg->tx_len + 1) & 0xffff) << 8;
+		pkt |= (((msg->tx_len + 1) >> 8) & 0xffff) << 16;
+	} else {
+		pkt |= (((u8 *)msg->tx_buf)[0] << 8);
+		if (msg->tx_len > 1)
+			pkt |= (((u8 *)msg->tx_buf)[1] << 16);
+	}
+
+	pkt |= sun6i_dsi_ecc_compute(pkt) << 24;
+
+	return pkt;
+}
+
+static int sun6i_dsi_dcs_write_short(struct sun6i_dsi *dsi,
+				     const struct mipi_dsi_msg *msg)
+{
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0),
+		     sun6i_dsi_dcs_build_pkt_hdr(dsi, msg));
+	regmap_write_bits(dsi->regs, SUN6I_DSI_CMD_CTL_REG,
+			  0xff, (4 - 1));
+
+	sun6i_dsi_start(dsi, DSI_START_LPTX);
+
+	return msg->tx_len;
+}
+
+static int sun6i_dsi_dcs_write_long(struct sun6i_dsi *dsi,
+				    const struct mipi_dsi_msg *msg)
+{
+	int ret, len = 0;
+	u8 *bounce;
+	u16 crc;
+
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0),
+		     sun6i_dsi_dcs_build_pkt_hdr(dsi, msg));
+
+	bounce = kzalloc(msg->tx_len + sizeof(crc), GFP_KERNEL);
+	if (!bounce)
+		return -ENOMEM;
+
+	memcpy(bounce, msg->tx_buf, msg->tx_len);
+	len += msg->tx_len;
+
+	crc = sun6i_dsi_crc_compute(bounce, msg->tx_len);
+	memcpy((u8 *)bounce + msg->tx_len, &crc, sizeof(crc));
+	len += sizeof(crc);
+
+	regmap_bulk_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(1), bounce, len);
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG, len + 4 - 1);
+	kfree(bounce);
+
+	sun6i_dsi_start(dsi, DSI_START_LPTX);
+
+	ret = sun6i_dsi_inst_wait_for_completion(dsi);
+	if (ret < 0) {
+		sun6i_dsi_inst_abort(dsi);
+		return ret;
+	}
+
+	/*
+	 * TODO: There's some bits (reg 0x200, bits 8/9) that
+	 * apparently can be used to check whether the data have been
+	 * sent, but I couldn't get it to work reliably.
+	 */
+	return msg->tx_len;
+}
+
+static int sun6i_dsi_dcs_read(struct sun6i_dsi *dsi,
+			      const struct mipi_dsi_msg *msg)
+{
+	u32 val;
+	int ret;
+	u8 byte0;
+
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0),
+		     sun6i_dsi_dcs_build_pkt_hdr(dsi, msg));
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG,
+		     (4 - 1));
+
+	sun6i_dsi_start(dsi, DSI_START_LPRX);
+
+	ret = sun6i_dsi_inst_wait_for_completion(dsi);
+	if (ret < 0) {
+		sun6i_dsi_inst_abort(dsi);
+		return ret;
+	}
+
+	/*
+	 * TODO: There's some bits (reg 0x200, bits 24/25) that
+	 * apparently can be used to check whether the data have been
+	 * received, but I couldn't get it to work reliably.
+	 */
+	regmap_read(dsi->regs, SUN6I_DSI_CMD_CTL_REG, &val);
+	if (val & SUN6I_DSI_CMD_CTL_RX_OVERFLOW)
+		return -EIO;
+
+	regmap_read(dsi->regs, SUN6I_DSI_CMD_RX_REG(0), &val);
+	byte0 = val & 0xff;
+	if (byte0 == MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT)
+		return -EIO;
+
+	((u8 *)msg->rx_buf)[0] = (val >> 8);
+
+	return 1;
+}
+
+static int sun6i_dsi_attach(struct mipi_dsi_host *host,
+			    struct mipi_dsi_device *device)
+{
+	struct sun6i_dsi *dsi = host_to_sun6i_dsi(host);
+
+	dsi->device = device;
+	dsi->panel = of_drm_find_panel(device->dev.of_node);
+	if (!dsi->panel)
+		return -EINVAL;
+
+	dev_info(host->dev, "Attached device %s\n", device->name);
+
+	return 0;
+}
+
+static int sun6i_dsi_detach(struct mipi_dsi_host *host,
+			    struct mipi_dsi_device *device)
+{
+	struct sun6i_dsi *dsi = host_to_sun6i_dsi(host);
+
+	dsi->panel = NULL;
+	dsi->device = NULL;
+
+	return 0;
+}
+
+static ssize_t sun6i_dsi_transfer(struct mipi_dsi_host *host,
+				  const struct mipi_dsi_msg *msg)
+{
+	struct sun6i_dsi *dsi = host_to_sun6i_dsi(host);
+	int ret;
+
+	ret = sun6i_dsi_inst_wait_for_completion(dsi);
+	if (ret < 0)
+		sun6i_dsi_inst_abort(dsi);
+
+	regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG,
+		     SUN6I_DSI_CMD_CTL_RX_OVERFLOW |
+		     SUN6I_DSI_CMD_CTL_RX_FLAG |
+		     SUN6I_DSI_CMD_CTL_TX_FLAG);
+
+	switch (msg->type) {
+	case MIPI_DSI_DCS_SHORT_WRITE:
+	case MIPI_DSI_DCS_SHORT_WRITE_PARAM:
+		ret = sun6i_dsi_dcs_write_short(dsi, msg);
+		break;
+
+	case MIPI_DSI_DCS_LONG_WRITE:
+		ret = sun6i_dsi_dcs_write_long(dsi, msg);
+		break;
+
+	case MIPI_DSI_DCS_READ:
+		if (msg->rx_len == 1) {
+			ret = sun6i_dsi_dcs_read(dsi, msg);
+			break;
+		}
+
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+static const struct mipi_dsi_host_ops sun6i_dsi_host_ops = {
+	.attach		= sun6i_dsi_attach,
+	.detach		= sun6i_dsi_detach,
+	.transfer	= sun6i_dsi_transfer,
+};
+
+static const struct regmap_config sun6i_dsi_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+	.max_register	= SUN6I_DSI_CMD_TX_REG(255),
+	.name		= "mipi-dsi",
+};
+
+static int sun6i_dsi_bind(struct device *dev, struct device *master,
+			 void *data)
+{
+	struct drm_device *drm = data;
+	struct sun4i_drv *drv = drm->dev_private;
+	struct sun6i_dsi *dsi = dev_get_drvdata(dev);
+	int ret;
+
+	if (!dsi->panel)
+		return -EPROBE_DEFER;
+
+	dsi->drv = drv;
+
+	drm_encoder_helper_add(&dsi->encoder,
+			       &sun6i_dsi_enc_helper_funcs);
+	ret = drm_encoder_init(drm,
+			       &dsi->encoder,
+			       &sun6i_dsi_enc_funcs,
+			       DRM_MODE_ENCODER_DSI,
+			       NULL);
+	if (ret) {
+		dev_err(dsi->dev, "Couldn't initialise the DSI encoder\n");
+		return ret;
+	}
+	dsi->encoder.possible_crtcs = BIT(0);
+
+	drm_connector_helper_add(&dsi->connector,
+				 &sun6i_dsi_connector_helper_funcs);
+	ret = drm_connector_init(drm, &dsi->connector,
+				 &sun6i_dsi_connector_funcs,
+				 DRM_MODE_CONNECTOR_DSI);
+	if (ret) {
+		dev_err(dsi->dev,
+			"Couldn't initialise the DSI connector\n");
+		goto err_cleanup_connector;
+	}
+
+	drm_mode_connector_attach_encoder(&dsi->connector, &dsi->encoder);
+	drm_panel_attach(dsi->panel, &dsi->connector);
+
+	return 0;
+
+err_cleanup_connector:
+	drm_encoder_cleanup(&dsi->encoder);
+	return ret;
+}
+
+static void sun6i_dsi_unbind(struct device *dev, struct device *master,
+			    void *data)
+{
+	struct sun6i_dsi *dsi = dev_get_drvdata(dev);
+
+	drm_panel_detach(dsi->panel);
+}
+
+static const struct component_ops sun6i_dsi_ops = {
+	.bind	= sun6i_dsi_bind,
+	.unbind	= sun6i_dsi_unbind,
+};
+
+static int sun6i_dsi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *dphy_node;
+	struct sun6i_dsi *dsi;
+	struct resource *res;
+	void __iomem *base;
+	int ret;
+
+	dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+	if (!dsi)
+		return -ENOMEM;
+	dev_set_drvdata(dev, dsi);
+	dsi->dev = dev;
+	dsi->host.ops = &sun6i_dsi_host_ops;
+	dsi->host.dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(base)) {
+		dev_err(dev, "Couldn't map the DSI encoder registers\n");
+		return PTR_ERR(base);
+	}
+
+	dsi->regs = devm_regmap_init_mmio_clk(dev, "bus", base,
+					      &sun6i_dsi_regmap_config);
+	if (IS_ERR(dsi->regs)) {
+		dev_err(dev, "Couldn't create the DSI encoder regmap\n");
+		return PTR_ERR(dsi->regs);
+	}
+
+	dsi->reset = devm_reset_control_get_shared(dev, NULL);
+	if (IS_ERR(dsi->reset)) {
+		dev_err(dev, "Couldn't get our reset line\n");
+		return PTR_ERR(dsi->reset);
+	}
+
+	dsi->mod_clk = devm_clk_get(dev, "mod");
+	if (IS_ERR(dsi->mod_clk)) {
+		dev_err(dev, "Couldn't get the DSI mod clock\n");
+		return PTR_ERR(dsi->mod_clk);
+	}
+
+	/*
+	 * In order to operate properly, that clock seems to be always
+	 * set to 297MHz.
+	 */
+	clk_set_rate_exclusive(dsi->mod_clk, 297000000);
+
+	dphy_node = of_parse_phandle(dev->of_node, "phys", 0);
+	ret = sun6i_dphy_probe(dsi, dphy_node);
+	of_node_put(dphy_node);
+	if (ret) {
+		dev_err(dev, "Couldn't get the MIPI D-PHY\n");
+		goto err_unprotect_clk;
+	}
+
+	pm_runtime_enable(dev);
+
+	ret = mipi_dsi_host_register(&dsi->host);
+	if (ret) {
+		dev_err(dev, "Couldn't register MIPI-DSI host\n");
+		goto err_remove_phy;
+	}
+
+	ret = component_add(&pdev->dev, &sun6i_dsi_ops);
+	if (ret) {
+		dev_err(dev, "Couldn't register our component\n");
+		goto err_remove_dsi_host;
+	}
+
+	return 0;
+
+err_remove_dsi_host:
+	mipi_dsi_host_unregister(&dsi->host);
+err_remove_phy:
+	pm_runtime_disable(dev);
+	sun6i_dphy_remove(dsi);
+err_unprotect_clk:
+	clk_rate_exclusive_put(dsi->mod_clk);
+	return ret;
+}
+
+static int sun6i_dsi_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct sun6i_dsi *dsi = dev_get_drvdata(dev);
+
+	component_del(&pdev->dev, &sun6i_dsi_ops);
+	mipi_dsi_host_unregister(&dsi->host);
+	pm_runtime_disable(dev);
+	sun6i_dphy_remove(dsi);
+	clk_rate_exclusive_put(dsi->mod_clk);
+
+	return 0;
+}
+
+static int sun6i_dsi_runtime_resume(struct device *dev)
+{
+	struct sun6i_dsi *dsi = dev_get_drvdata(dev);
+
+	reset_control_deassert(dsi->reset);
+	clk_prepare_enable(dsi->mod_clk);
+
+	/*
+	 * Enable the DSI block.
+	 *
+	 * Some part of it can only be done once we get a number of
+	 * lanes, see sun6i_dsi_inst_init
+	 */
+	regmap_write(dsi->regs, SUN6I_DSI_CTL_REG, SUN6I_DSI_CTL_EN);
+
+	regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG,
+		     SUN6I_DSI_BASIC_CTL0_ECC_EN | SUN6I_DSI_BASIC_CTL0_CRC_EN);
+
+	regmap_write(dsi->regs, SUN6I_DSI_TRANS_START_REG, 10);
+	regmap_write(dsi->regs, SUN6I_DSI_TRANS_ZERO_REG, 0);
+
+	if (dsi->device)
+		sun6i_dsi_inst_init(dsi, dsi->device);
+
+	regmap_write(dsi->regs, SUN6I_DSI_DEBUG_DATA_REG, 0xff);
+
+	return 0;
+}
+
+static int sun6i_dsi_runtime_suspend(struct device *dev)
+{
+	struct sun6i_dsi *dsi = dev_get_drvdata(dev);
+
+	clk_disable_unprepare(dsi->mod_clk);
+	reset_control_assert(dsi->reset);
+
+	return 0;
+}
+
+static const struct dev_pm_ops sun6i_dsi_pm_ops = {
+	SET_RUNTIME_PM_OPS(sun6i_dsi_runtime_suspend,
+			   sun6i_dsi_runtime_resume,
+			   NULL)
+};
+
+static const struct of_device_id sun6i_dsi_of_table[] = {
+	{ .compatible = "allwinner,sun6i-a31-mipi-dsi" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun6i_dsi_of_table);
+
+static struct platform_driver sun6i_dsi_platform_driver = {
+	.probe		= sun6i_dsi_probe,
+	.remove		= sun6i_dsi_remove,
+	.driver		= {
+		.name		= "sun6i-mipi-dsi",
+		.of_match_table	= sun6i_dsi_of_table,
+		.pm		= &sun6i_dsi_pm_ops,
+	},
+};
+module_platform_driver(sun6i_dsi_platform_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Allwinner A31 DSI Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h
new file mode 100644
index 000000000000..dbbc5b3ecbda
--- /dev/null
+++ b/drivers/gpu/drm/sun4i/sun6i_mipi_dsi.h
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2016 Allwinnertech Co., Ltd.
+ * Copyright (C) 2017-2018 Bootlin
+ *
+ * Maxime Ripard <maxime.ripard@bootlin.com>
+ */
+
+#ifndef _SUN6I_MIPI_DSI_H_
+#define _SUN6I_MIPI_DSI_H_
+
+#include <drm/drm_connector.h>
+#include <drm/drm_encoder.h>
+#include <drm/drm_mipi_dsi.h>
+
+struct sun6i_dphy {
+	struct clk		*bus_clk;
+	struct clk		*mod_clk;
+	struct regmap		*regs;
+	struct reset_control	*reset;
+};
+
+struct sun6i_dsi {
+	struct drm_connector	connector;
+	struct drm_encoder	encoder;
+	struct mipi_dsi_host	host;
+
+	struct clk		*bus_clk;
+	struct clk		*mod_clk;
+	struct regmap		*regs;
+	struct reset_control	*reset;
+	struct sun6i_dphy	*dphy;
+
+	struct device		*dev;
+	struct sun4i_drv	*drv;
+	struct mipi_dsi_device	*device;
+	struct drm_panel	*panel;
+};
+
+static inline struct sun6i_dsi *host_to_sun6i_dsi(struct mipi_dsi_host *host)
+{
+	return container_of(host, struct sun6i_dsi, host);
+};
+
+static inline struct sun6i_dsi *connector_to_sun6i_dsi(struct drm_connector *connector)
+{
+	return container_of(connector, struct sun6i_dsi, connector);
+};
+
+static inline struct sun6i_dsi *encoder_to_sun6i_dsi(const struct drm_encoder *encoder)
+{
+	return container_of(encoder, struct sun6i_dsi, encoder);
+};
+
+int sun6i_dphy_probe(struct sun6i_dsi *dsi, struct device_node *node);
+int sun6i_dphy_remove(struct sun6i_dsi *dsi);
+
+int sun6i_dphy_init(struct sun6i_dphy *dphy, unsigned int lanes);
+int sun6i_dphy_power_on(struct sun6i_dphy *dphy, unsigned int lanes);
+int sun6i_dphy_power_off(struct sun6i_dphy *dphy);
+int sun6i_dphy_exit(struct sun6i_dphy *dphy);
+
+#endif /* _SUN6I_MIPI_DSI_H_ */
-- 
git-series 0.9.1

[PATCH v4 4/8] drm/sun4i: Tie the DSI controller in the TCON

[Maxime Ripard]

The DSI controller needs a particular interface (CPU aka 8080) with some
modifications from the TCON in order to run.

Make sure the TCON is able to provide it when we are using the DSI output.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 drivers/gpu/drm/sun4i/sun4i_tcon.c | 77 +++++++++++++++++++++++++++++++-
 drivers/gpu/drm/sun4i/sun4i_tcon.h | 42 +++++++++++++++++-
 2 files changed, 119 insertions(+)

diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index 5f423ed2f01b..08747fc3ee71 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -35,6 +35,7 @@
 #include "sun4i_lvds.h"
 #include "sun4i_rgb.h"
 #include "sun4i_tcon.h"
+#include "sun6i_mipi_dsi.h"
 #include "sunxi_engine.h"
 
 static struct drm_connector *sun4i_tcon_get_connector(const struct drm_encoder *encoder)
@@ -169,6 +170,7 @@ void sun4i_tcon_set_status(struct sun4i_tcon *tcon,
 	case DRM_MODE_ENCODER_LVDS:
 		is_lvds = true;
 		/* Fallthrough */
+	case DRM_MODE_ENCODER_DSI:
 	case DRM_MODE_ENCODER_NONE:
 		channel = 0;
 		break;
@@ -274,6 +276,71 @@ static void sun4i_tcon0_mode_set_common(struct sun4i_tcon *tcon,
 		     SUN4I_TCON0_BASIC0_Y(mode->crtc_vdisplay));
 }
 
+static void sun4i_tcon0_mode_set_cpu(struct sun4i_tcon *tcon,
+				     struct mipi_dsi_device *device,
+				     const struct drm_display_mode *mode)
+{
+	u8 bpp = mipi_dsi_pixel_format_to_bpp(device->format);
+	u8 lanes = device->lanes;
+	u32 block_space, start_delay;
+	u32 tcon_div;
+
+	tcon->dclk_min_div = 4;
+	tcon->dclk_max_div = 127;
+
+	sun4i_tcon0_mode_set_common(tcon, mode);
+
+	regmap_update_bits(tcon->regs, SUN4I_TCON0_CTL_REG,
+			   SUN4I_TCON0_CTL_IF_MASK,
+			   SUN4I_TCON0_CTL_IF_8080);
+
+	regmap_write(tcon->regs, SUN4I_TCON_ECC_FIFO_REG,
+		     SUN4I_TCON_ECC_FIFO_EN);
+
+	regmap_write(tcon->regs, SUN4I_TCON0_CPU_IF_REG,
+		     SUN4I_TCON0_CPU_IF_MODE_DSI |
+		     SUN4I_TCON0_CPU_IF_TRI_FIFO_FLUSH |
+		     SUN4I_TCON0_CPU_IF_TRI_FIFO_EN |
+		     SUN4I_TCON0_CPU_IF_TRI_EN);
+
+	/*
+	 * This looks suspicious, but it works...
+	 *
+	 * The datasheet says that this should be set higher than 20 *
+	 * pixel cycle, but it's not clear what a pixel cycle is.
+	 */
+	regmap_read(tcon->regs, SUN4I_TCON0_DCLK_REG, &tcon_div);
+	tcon_div &= GENMASK(6, 0);
+	block_space = mode->htotal * bpp / (tcon_div * lanes);
+	block_space -= mode->hdisplay + 40;
+
+	regmap_write(tcon->regs, SUN4I_TCON0_CPU_TRI0_REG,
+		     SUN4I_TCON0_CPU_TRI0_BLOCK_SPACE(block_space) |
+		     SUN4I_TCON0_CPU_TRI0_BLOCK_SIZE(mode->hdisplay));
+
+	regmap_write(tcon->regs, SUN4I_TCON0_CPU_TRI1_REG,
+		     SUN4I_TCON0_CPU_TRI1_BLOCK_NUM(mode->vdisplay));
+
+	start_delay = (mode->crtc_vtotal - mode->crtc_vdisplay - 10 - 1);
+	start_delay = start_delay * mode->crtc_htotal * 149;
+	start_delay = start_delay / (mode->crtc_clock / 1000) / 8;
+	regmap_write(tcon->regs, SUN4I_TCON0_CPU_TRI2_REG,
+		     SUN4I_TCON0_CPU_TRI2_TRANS_START_SET(10) |
+		     SUN4I_TCON0_CPU_TRI2_START_DELAY(start_delay));
+
+	/*
+	 * The Allwinner BSP has a comment that the period should be
+	 * the display clock * 15, but uses an hardcoded 3000...
+	 */
+	regmap_write(tcon->regs, SUN4I_TCON_SAFE_PERIOD_REG,
+		     SUN4I_TCON_SAFE_PERIOD_NUM(3000) |
+		     SUN4I_TCON_SAFE_PERIOD_MODE(3));
+
+	/* Enable the output on the pins */
+	regmap_write(tcon->regs, SUN4I_TCON0_IO_TRI_REG,
+		     0xe0000000);
+}
+
 static void sun4i_tcon0_mode_set_lvds(struct sun4i_tcon *tcon,
 				      const struct drm_encoder *encoder,
 				      const struct drm_display_mode *mode)
@@ -539,7 +606,17 @@ void sun4i_tcon_mode_set(struct sun4i_tcon *tcon,
 			 const struct drm_encoder *encoder,
 			 const struct drm_display_mode *mode)
 {
+	struct sun6i_dsi *dsi;
+
 	switch (encoder->encoder_type) {
+	case DRM_MODE_ENCODER_DSI:
+		/*
+		 * This is not really elegant, but it's the "cleaner"
+		 * way I could think of...
+		 */
+		dsi = encoder_to_sun6i_dsi(encoder);
+		sun4i_tcon0_mode_set_cpu(tcon, dsi->device, mode);
+		break;
 	case DRM_MODE_ENCODER_LVDS:
 		sun4i_tcon0_mode_set_lvds(tcon, encoder, mode);
 		break;
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.h b/drivers/gpu/drm/sun4i/sun4i_tcon.h
index 2e0fb9640ed9..f6a071cd5a6f 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.h
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.h
@@ -35,10 +35,25 @@
 #define SUN4I_TCON_GINT0_TCON0_TRI_COUNTER_INT		BIT(10)
 
 #define SUN4I_TCON_GINT1_REG			0x8
+
 #define SUN4I_TCON_FRM_CTL_REG			0x10
+#define SUN4I_TCON_FRM_CTL_EN				BIT(31)
+
+#define SUN4I_TCON_FRM_SEED_PR_REG		0x14
+#define SUN4I_TCON_FRM_SEED_PG_REG		0x18
+#define SUN4I_TCON_FRM_SEED_PB_REG		0x1c
+#define SUN4I_TCON_FRM_SEED_LR_REG		0x20
+#define SUN4I_TCON_FRM_SEED_LG_REG		0x24
+#define SUN4I_TCON_FRM_SEED_LB_REG		0x28
+#define SUN4I_TCON_FRM_TBL0_REG			0x2c
+#define SUN4I_TCON_FRM_TBL1_REG			0x30
+#define SUN4I_TCON_FRM_TBL2_REG			0x34
+#define SUN4I_TCON_FRM_TBL3_REG			0x38
 
 #define SUN4I_TCON0_CTL_REG			0x40
 #define SUN4I_TCON0_CTL_TCON_ENABLE			BIT(31)
+#define SUN4I_TCON0_CTL_IF_MASK				GENMASK(25, 24)
+#define SUN4I_TCON0_CTL_IF_8080				(1 << 24)
 #define SUN4I_TCON0_CTL_CLK_DELAY_MASK			GENMASK(8, 4)
 #define SUN4I_TCON0_CTL_CLK_DELAY(delay)		((delay << 4) & SUN4I_TCON0_CTL_CLK_DELAY_MASK)
 #define SUN4I_TCON0_CTL_SRC_SEL_MASK			GENMASK(2, 0)
@@ -65,7 +80,14 @@
 #define SUN4I_TCON0_BASIC3_V_SYNC(height)		(((height) - 1) & 0x7ff)
 
 #define SUN4I_TCON0_HV_IF_REG			0x58
+
 #define SUN4I_TCON0_CPU_IF_REG			0x60
+#define SUN4I_TCON0_CPU_IF_MODE_MASK			GENMASK(31, 28)
+#define SUN4I_TCON0_CPU_IF_MODE_DSI			(1 << 28)
+#define SUN4I_TCON0_CPU_IF_TRI_FIFO_FLUSH		BIT(16)
+#define SUN4I_TCON0_CPU_IF_TRI_FIFO_EN			BIT(2)
+#define SUN4I_TCON0_CPU_IF_TRI_EN			BIT(0)
+
 #define SUN4I_TCON0_CPU_WR_REG			0x64
 #define SUN4I_TCON0_CPU_RD0_REG			0x68
 #define SUN4I_TCON0_CPU_RDA_REG			0x6c
@@ -132,6 +154,10 @@
 
 #define SUN4I_TCON1_IO_POL_REG			0xf0
 #define SUN4I_TCON1_IO_TRI_REG			0xf4
+
+#define SUN4I_TCON_ECC_FIFO_REG			0xf8
+#define SUN4I_TCON_ECC_FIFO_EN				BIT(3)
+
 #define SUN4I_TCON_CEU_CTL_REG			0x100
 #define SUN4I_TCON_CEU_MUL_RR_REG		0x110
 #define SUN4I_TCON_CEU_MUL_RG_REG		0x114
@@ -148,6 +174,22 @@
 #define SUN4I_TCON_CEU_RANGE_R_REG		0x140
 #define SUN4I_TCON_CEU_RANGE_G_REG		0x144
 #define SUN4I_TCON_CEU_RANGE_B_REG		0x148
+
+#define SUN4I_TCON0_CPU_TRI0_REG		0x160
+#define SUN4I_TCON0_CPU_TRI0_BLOCK_SPACE(space)		((((space) - 1) & 0xfff) << 16)
+#define SUN4I_TCON0_CPU_TRI0_BLOCK_SIZE(size)		(((size) - 1) & 0xfff)
+
+#define SUN4I_TCON0_CPU_TRI1_REG		0x164
+#define SUN4I_TCON0_CPU_TRI1_BLOCK_NUM(num)		(((num) - 1) & 0xffff)
+
+#define SUN4I_TCON0_CPU_TRI2_REG		0x168
+#define SUN4I_TCON0_CPU_TRI2_START_DELAY(delay)		(((delay) & 0xffff) << 16)
+#define SUN4I_TCON0_CPU_TRI2_TRANS_START_SET(set)	((set) & 0xfff)
+
+#define SUN4I_TCON_SAFE_PERIOD_REG		0x1f0
+#define SUN4I_TCON_SAFE_PERIOD_NUM(num)			(((num) & 0xfff) << 16)
+#define SUN4I_TCON_SAFE_PERIOD_MODE(mode)		((mode) & 0x3)
+
 #define SUN4I_TCON_MUX_CTRL_REG			0x200
 
 #define SUN4I_TCON0_LVDS_ANA0_REG		0x220
-- 
git-series 0.9.1

[PATCH v4 5/8] dt-bindings: panel: Add the Ilitek ILI9881c panel documentation

[Maxime Ripard]

The LHR050H41 from BananaPi is a 1280x700 4-lanes DSI panel based on the
ILI9881c from Ilitek.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt

diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt
new file mode 100644
index 000000000000..df05e8bb4851
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9881c.txt
@@ -0,0 +1,20 @@
+Ilitek ILI9881c based MIPI-DSI panels
+
+Required properties:
+  - compatible: must be "ilitek,ili9881c" and one of:
+    * "bananapi,lhr050h41"
+  - reg: DSI virtual channel used by that screen
+  - power-gpios: a GPIO phandle for the power pin
+  - reset-gpios: a GPIO phandle for the reset pin
+
+Optional properties:
+  - backlight: phandle to the backlight used
+
+Example:
+panel@0 {
+	compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+	reg = <0>;
+	power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
+	reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
+	backlight = <&pwm_bl>;
+};
-- 
git-series 0.9.1

[PATCH v4 6/8] drm/panel: Add Ilitek ILI9881c panel driver

[Maxime Ripard]

The LHR050H41 panel is the panel shipped with the BananaPi M2-Magic, and is
based on the Ilitek ILI9881c Controller. Add a driver for it, modelled
after the other Ilitek controller drivers.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 drivers/gpu/drm/panel/Kconfig                 |   9 +-
 drivers/gpu/drm/panel/Makefile                |   1 +-
 drivers/gpu/drm/panel/panel-ilitek-ili9881c.c | 489 +++++++++++++++++++-
 3 files changed, 499 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9881c.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index 25682ff3449a..6020c30a33b3 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -46,6 +46,15 @@ config DRM_PANEL_ILITEK_IL9322
 	  Say Y here if you want to enable support for Ilitek IL9322
 	  QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
 
+config DRM_PANEL_ILITEK_ILI9881C
+	tristate "Ilitek ILI9881C-based panels"
+	depends on OF
+	depends on DRM_MIPI_DSI
+	depends on BACKLIGHT_CLASS_DEVICE
+	help
+	  Say Y if you want to enable support for panels based on the
+	  Ilitek ILI9881c controller.
+
 config DRM_PANEL_INNOLUX_P079ZCA
 	tristate "Innolux P079ZCA panel"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index f26efc11d746..5ccaaa9d13af 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
 obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
 obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
+obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
 obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
 obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
 obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c b/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
new file mode 100644
index 000000000000..8992a6431c30
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
@@ -0,0 +1,489 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017, Free Electrons
+ * Author: Maxime Ripard <maxime.ripard@free-electrons.com>
+ */
+
+#include <linux/backlight.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/fb.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include <linux/gpio/consumer.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+#include <video/mipi_display.h>
+
+struct ili9881c {
+	struct drm_panel	panel;
+	struct mipi_dsi_device	*dsi;
+
+	struct backlight_device *backlight;
+	struct gpio_desc	*power;
+	struct gpio_desc	*reset;
+};
+
+enum ili9881c_op {
+	ILI9881C_SWITCH_PAGE,
+	ILI9881C_COMMAND,
+};
+
+struct ili9881c_instr {
+	enum ili9881c_op	op;
+
+	union arg {
+		struct cmd {
+			u8	cmd;
+			u8	data;
+		} cmd;
+		u8	page;
+	} arg;
+};
+
+#define ILI9881C_SWITCH_PAGE_INSTR(_page)	\
+	{					\
+		.op = ILI9881C_SWITCH_PAGE,	\
+		.arg = {			\
+			.page = (_page),	\
+		},				\
+	}
+
+#define ILI9881C_COMMAND_INSTR(_cmd, _data)		\
+	{						\
+		.op = ILI9881C_COMMAND,		\
+		.arg = {				\
+			.cmd = {			\
+				.cmd = (_cmd),		\
+				.data = (_data),	\
+			},				\
+		},					\
+	}
+
+static struct ili9881c_instr ili9881c_init[] = {
+	ILI9881C_SWITCH_PAGE_INSTR(3),
+	ILI9881C_COMMAND_INSTR(0x01, 0x00),
+	ILI9881C_COMMAND_INSTR(0x02, 0x00),
+	ILI9881C_COMMAND_INSTR(0x03, 0x73),
+	ILI9881C_COMMAND_INSTR(0x04, 0x03),
+	ILI9881C_COMMAND_INSTR(0x05, 0x00),
+	ILI9881C_COMMAND_INSTR(0x06, 0x06),
+	ILI9881C_COMMAND_INSTR(0x07, 0x06),
+	ILI9881C_COMMAND_INSTR(0x08, 0x00),
+	ILI9881C_COMMAND_INSTR(0x09, 0x18),
+	ILI9881C_COMMAND_INSTR(0x0a, 0x04),
+	ILI9881C_COMMAND_INSTR(0x0b, 0x00),
+	ILI9881C_COMMAND_INSTR(0x0c, 0x02),
+	ILI9881C_COMMAND_INSTR(0x0d, 0x03),
+	ILI9881C_COMMAND_INSTR(0x0e, 0x00),
+	ILI9881C_COMMAND_INSTR(0x0f, 0x25),
+	ILI9881C_COMMAND_INSTR(0x10, 0x25),
+	ILI9881C_COMMAND_INSTR(0x11, 0x00),
+	ILI9881C_COMMAND_INSTR(0x12, 0x00),
+	ILI9881C_COMMAND_INSTR(0x13, 0x00),
+	ILI9881C_COMMAND_INSTR(0x14, 0x00),
+	ILI9881C_COMMAND_INSTR(0x15, 0x00),
+	ILI9881C_COMMAND_INSTR(0x16, 0x0C),
+	ILI9881C_COMMAND_INSTR(0x17, 0x00),
+	ILI9881C_COMMAND_INSTR(0x18, 0x00),
+	ILI9881C_COMMAND_INSTR(0x19, 0x00),
+	ILI9881C_COMMAND_INSTR(0x1a, 0x00),
+	ILI9881C_COMMAND_INSTR(0x1b, 0x00),
+	ILI9881C_COMMAND_INSTR(0x1c, 0x00),
+	ILI9881C_COMMAND_INSTR(0x1d, 0x00),
+	ILI9881C_COMMAND_INSTR(0x1e, 0xC0),
+	ILI9881C_COMMAND_INSTR(0x1f, 0x80),
+	ILI9881C_COMMAND_INSTR(0x20, 0x04),
+	ILI9881C_COMMAND_INSTR(0x21, 0x01),
+	ILI9881C_COMMAND_INSTR(0x22, 0x00),
+	ILI9881C_COMMAND_INSTR(0x23, 0x00),
+	ILI9881C_COMMAND_INSTR(0x24, 0x00),
+	ILI9881C_COMMAND_INSTR(0x25, 0x00),
+	ILI9881C_COMMAND_INSTR(0x26, 0x00),
+	ILI9881C_COMMAND_INSTR(0x27, 0x00),
+	ILI9881C_COMMAND_INSTR(0x28, 0x33),
+	ILI9881C_COMMAND_INSTR(0x29, 0x03),
+	ILI9881C_COMMAND_INSTR(0x2a, 0x00),
+	ILI9881C_COMMAND_INSTR(0x2b, 0x00),
+	ILI9881C_COMMAND_INSTR(0x2c, 0x00),
+	ILI9881C_COMMAND_INSTR(0x2d, 0x00),
+	ILI9881C_COMMAND_INSTR(0x2e, 0x00),
+	ILI9881C_COMMAND_INSTR(0x2f, 0x00),
+	ILI9881C_COMMAND_INSTR(0x30, 0x00),
+	ILI9881C_COMMAND_INSTR(0x31, 0x00),
+	ILI9881C_COMMAND_INSTR(0x32, 0x00),
+	ILI9881C_COMMAND_INSTR(0x33, 0x00),
+	ILI9881C_COMMAND_INSTR(0x34, 0x04),
+	ILI9881C_COMMAND_INSTR(0x35, 0x00),
+	ILI9881C_COMMAND_INSTR(0x36, 0x00),
+	ILI9881C_COMMAND_INSTR(0x37, 0x00),
+	ILI9881C_COMMAND_INSTR(0x38, 0x3C),
+	ILI9881C_COMMAND_INSTR(0x39, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3a, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3b, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3c, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3d, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3e, 0x00),
+	ILI9881C_COMMAND_INSTR(0x3f, 0x00),
+	ILI9881C_COMMAND_INSTR(0x40, 0x00),
+	ILI9881C_COMMAND_INSTR(0x41, 0x00),
+	ILI9881C_COMMAND_INSTR(0x42, 0x00),
+	ILI9881C_COMMAND_INSTR(0x43, 0x00),
+	ILI9881C_COMMAND_INSTR(0x44, 0x00),
+	ILI9881C_COMMAND_INSTR(0x50, 0x01),
+	ILI9881C_COMMAND_INSTR(0x51, 0x23),
+	ILI9881C_COMMAND_INSTR(0x52, 0x45),
+	ILI9881C_COMMAND_INSTR(0x53, 0x67),
+	ILI9881C_COMMAND_INSTR(0x54, 0x89),
+	ILI9881C_COMMAND_INSTR(0x55, 0xab),
+	ILI9881C_COMMAND_INSTR(0x56, 0x01),
+	ILI9881C_COMMAND_INSTR(0x57, 0x23),
+	ILI9881C_COMMAND_INSTR(0x58, 0x45),
+	ILI9881C_COMMAND_INSTR(0x59, 0x67),
+	ILI9881C_COMMAND_INSTR(0x5a, 0x89),
+	ILI9881C_COMMAND_INSTR(0x5b, 0xab),
+	ILI9881C_COMMAND_INSTR(0x5c, 0xcd),
+	ILI9881C_COMMAND_INSTR(0x5d, 0xef),
+	ILI9881C_COMMAND_INSTR(0x5e, 0x11),
+	ILI9881C_COMMAND_INSTR(0x5f, 0x02),
+	ILI9881C_COMMAND_INSTR(0x60, 0x02),
+	ILI9881C_COMMAND_INSTR(0x61, 0x02),
+	ILI9881C_COMMAND_INSTR(0x62, 0x02),
+	ILI9881C_COMMAND_INSTR(0x63, 0x02),
+	ILI9881C_COMMAND_INSTR(0x64, 0x02),
+	ILI9881C_COMMAND_INSTR(0x65, 0x02),
+	ILI9881C_COMMAND_INSTR(0x66, 0x02),
+	ILI9881C_COMMAND_INSTR(0x67, 0x02),
+	ILI9881C_COMMAND_INSTR(0x68, 0x02),
+	ILI9881C_COMMAND_INSTR(0x69, 0x02),
+	ILI9881C_COMMAND_INSTR(0x6a, 0x0C),
+	ILI9881C_COMMAND_INSTR(0x6b, 0x02),
+	ILI9881C_COMMAND_INSTR(0x6c, 0x0F),
+	ILI9881C_COMMAND_INSTR(0x6d, 0x0E),
+	ILI9881C_COMMAND_INSTR(0x6e, 0x0D),
+	ILI9881C_COMMAND_INSTR(0x6f, 0x06),
+	ILI9881C_COMMAND_INSTR(0x70, 0x07),
+	ILI9881C_COMMAND_INSTR(0x71, 0x02),
+	ILI9881C_COMMAND_INSTR(0x72, 0x02),
+	ILI9881C_COMMAND_INSTR(0x73, 0x02),
+	ILI9881C_COMMAND_INSTR(0x74, 0x02),
+	ILI9881C_COMMAND_INSTR(0x75, 0x02),
+	ILI9881C_COMMAND_INSTR(0x76, 0x02),
+	ILI9881C_COMMAND_INSTR(0x77, 0x02),
+	ILI9881C_COMMAND_INSTR(0x78, 0x02),
+	ILI9881C_COMMAND_INSTR(0x79, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7a, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7b, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7c, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7d, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7e, 0x02),
+	ILI9881C_COMMAND_INSTR(0x7f, 0x02),
+	ILI9881C_COMMAND_INSTR(0x80, 0x0C),
+	ILI9881C_COMMAND_INSTR(0x81, 0x02),
+	ILI9881C_COMMAND_INSTR(0x82, 0x0F),
+	ILI9881C_COMMAND_INSTR(0x83, 0x0E),
+	ILI9881C_COMMAND_INSTR(0x84, 0x0D),
+	ILI9881C_COMMAND_INSTR(0x85, 0x06),
+	ILI9881C_COMMAND_INSTR(0x86, 0x07),
+	ILI9881C_COMMAND_INSTR(0x87, 0x02),
+	ILI9881C_COMMAND_INSTR(0x88, 0x02),
+	ILI9881C_COMMAND_INSTR(0x89, 0x02),
+	ILI9881C_COMMAND_INSTR(0x8A, 0x02),
+	ILI9881C_SWITCH_PAGE_INSTR(4),
+	ILI9881C_COMMAND_INSTR(0x6C, 0x15),
+	ILI9881C_COMMAND_INSTR(0x6E, 0x22),
+	ILI9881C_COMMAND_INSTR(0x6F, 0x33),
+	ILI9881C_COMMAND_INSTR(0x3A, 0xA4),
+	ILI9881C_COMMAND_INSTR(0x8D, 0x0D),
+	ILI9881C_COMMAND_INSTR(0x87, 0xBA),
+	ILI9881C_COMMAND_INSTR(0x26, 0x76),
+	ILI9881C_COMMAND_INSTR(0xB2, 0xD1),
+	ILI9881C_SWITCH_PAGE_INSTR(1),
+	ILI9881C_COMMAND_INSTR(0x22, 0x0A),
+	ILI9881C_COMMAND_INSTR(0x53, 0xDC),
+	ILI9881C_COMMAND_INSTR(0x55, 0xA7),
+	ILI9881C_COMMAND_INSTR(0x50, 0x78),
+	ILI9881C_COMMAND_INSTR(0x51, 0x78),
+	ILI9881C_COMMAND_INSTR(0x31, 0x02),
+	ILI9881C_COMMAND_INSTR(0x60, 0x14),
+	ILI9881C_COMMAND_INSTR(0xA0, 0x2A),
+	ILI9881C_COMMAND_INSTR(0xA1, 0x39),
+	ILI9881C_COMMAND_INSTR(0xA2, 0x46),
+	ILI9881C_COMMAND_INSTR(0xA3, 0x0e),
+	ILI9881C_COMMAND_INSTR(0xA4, 0x12),
+	ILI9881C_COMMAND_INSTR(0xA5, 0x25),
+	ILI9881C_COMMAND_INSTR(0xA6, 0x19),
+	ILI9881C_COMMAND_INSTR(0xA7, 0x1d),
+	ILI9881C_COMMAND_INSTR(0xA8, 0xa6),
+	ILI9881C_COMMAND_INSTR(0xA9, 0x1C),
+	ILI9881C_COMMAND_INSTR(0xAA, 0x29),
+	ILI9881C_COMMAND_INSTR(0xAB, 0x85),
+	ILI9881C_COMMAND_INSTR(0xAC, 0x1C),
+	ILI9881C_COMMAND_INSTR(0xAD, 0x1B),
+	ILI9881C_COMMAND_INSTR(0xAE, 0x51),
+	ILI9881C_COMMAND_INSTR(0xAF, 0x22),
+	ILI9881C_COMMAND_INSTR(0xB0, 0x2d),
+	ILI9881C_COMMAND_INSTR(0xB1, 0x4f),
+	ILI9881C_COMMAND_INSTR(0xB2, 0x59),
+	ILI9881C_COMMAND_INSTR(0xB3, 0x3F),
+	ILI9881C_COMMAND_INSTR(0xC0, 0x2A),
+	ILI9881C_COMMAND_INSTR(0xC1, 0x3a),
+	ILI9881C_COMMAND_INSTR(0xC2, 0x45),
+	ILI9881C_COMMAND_INSTR(0xC3, 0x0e),
+	ILI9881C_COMMAND_INSTR(0xC4, 0x11),
+	ILI9881C_COMMAND_INSTR(0xC5, 0x24),
+	ILI9881C_COMMAND_INSTR(0xC6, 0x1a),
+	ILI9881C_COMMAND_INSTR(0xC7, 0x1c),
+	ILI9881C_COMMAND_INSTR(0xC8, 0xaa),
+	ILI9881C_COMMAND_INSTR(0xC9, 0x1C),
+	ILI9881C_COMMAND_INSTR(0xCA, 0x29),
+	ILI9881C_COMMAND_INSTR(0xCB, 0x96),
+	ILI9881C_COMMAND_INSTR(0xCC, 0x1C),
+	ILI9881C_COMMAND_INSTR(0xCD, 0x1B),
+	ILI9881C_COMMAND_INSTR(0xCE, 0x51),
+	ILI9881C_COMMAND_INSTR(0xCF, 0x22),
+	ILI9881C_COMMAND_INSTR(0xD0, 0x2b),
+	ILI9881C_COMMAND_INSTR(0xD1, 0x4b),
+	ILI9881C_COMMAND_INSTR(0xD2, 0x59),
+	ILI9881C_COMMAND_INSTR(0xD3, 0x3F),
+};
+
+static inline struct ili9881c *panel_to_ili9881c(struct drm_panel *panel)
+{
+	return container_of(panel, struct ili9881c, panel);
+}
+
+static int ili9881c_switch_page(struct ili9881c *ctx, u8 page)
+{
+	u8 buf[4] = { 0xff, 0x98, 0x81, page };
+	int ret;
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int ili9881c_send_cmd_data(struct ili9881c *ctx, u8 cmd, u8 data)
+{
+	u8 buf[2] = { cmd, data };
+	int ret;
+
+	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static int ili9881c_prepare(struct drm_panel *panel)
+{
+	struct ili9881c *ctx = panel_to_ili9881c(panel);
+	unsigned int i;
+	int ret;
+
+	/* Power the panel */
+	gpiod_set_value(ctx->power, 1);
+	msleep(5);
+
+	/* And reset it */
+	gpiod_set_value(ctx->reset, 1);
+	msleep(20);
+
+	gpiod_set_value(ctx->reset, 0);
+	msleep(20);
+
+	for (i = 0; i < ARRAY_SIZE(ili9881c_init); i++) {
+		struct ili9881c_instr *instr = &ili9881c_init[i];
+
+		if (instr->op == ILI9881C_SWITCH_PAGE)
+			ret = ili9881c_switch_page(ctx, instr->arg.page);
+		else if (instr->op == ILI9881C_COMMAND)
+			ret = ili9881c_send_cmd_data(ctx, instr->arg.cmd.cmd,
+						      instr->arg.cmd.data);
+
+		if (ret)
+			return ret;
+	}
+
+	ret = ili9881c_switch_page(ctx, 0);
+	if (ret)
+		return ret;
+
+	ret = mipi_dsi_dcs_set_tear_on(ctx->dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+	if (ret)
+		return ret;
+
+	mipi_dsi_dcs_exit_sleep_mode(ctx->dsi);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int ili9881c_enable(struct drm_panel *panel)
+{
+	struct ili9881c *ctx = panel_to_ili9881c(panel);
+
+	msleep(120);
+
+	mipi_dsi_dcs_set_display_on(ctx->dsi);
+	backlight_enable(ctx->backlight);
+
+	return 0;
+}
+
+static int ili9881c_disable(struct drm_panel *panel)
+{
+	struct ili9881c *ctx = panel_to_ili9881c(panel);
+
+	backlight_disable(ctx->backlight);
+	return mipi_dsi_dcs_set_display_off(ctx->dsi);
+}
+
+static int ili9881c_unprepare(struct drm_panel *panel)
+{
+	struct ili9881c *ctx = panel_to_ili9881c(panel);
+
+	mipi_dsi_dcs_enter_sleep_mode(ctx->dsi);
+	gpiod_set_value(ctx->power, 0);
+	gpiod_set_value(ctx->reset, 1);
+
+	return 0;
+}
+
+static const struct drm_display_mode default_mode = {
+	.clock		= 62000,
+	.vrefresh	= 60,
+
+	.hdisplay	= 720,
+	.hsync_start	= 720 + 10,
+	.hsync_end	= 720 + 10 + 20,
+	.htotal		= 720 + 10 + 20 + 30,
+
+	.vdisplay	= 1280,
+	.vsync_start	= 1280 + 10,
+	.vsync_end	= 1280 + 10 + 10,
+	.vtotal		= 1280 + 10 + 10 + 20,
+};
+
+static int ili9881c_get_modes(struct drm_panel *panel)
+{
+	struct drm_connector *connector = panel->connector;
+	struct ili9881c *ctx = panel_to_ili9881c(panel);
+	struct drm_display_mode *mode;
+
+	mode = drm_mode_duplicate(panel->drm, &default_mode);
+	if (!mode) {
+		dev_err(&ctx->dsi->dev, "failed to add mode %ux%ux@%u\n",
+			default_mode.hdisplay, default_mode.vdisplay,
+			default_mode.vrefresh);
+		return -ENOMEM;
+	}
+
+	drm_mode_set_name(mode);
+
+	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
+	drm_mode_probed_add(connector, mode);
+
+	panel->connector->display_info.width_mm = 62;
+	panel->connector->display_info.height_mm = 110;
+
+	return 1;
+}
+
+static const struct drm_panel_funcs ili9881c_funcs = {
+	.prepare	= ili9881c_prepare,
+	.unprepare	= ili9881c_unprepare,
+	.enable		= ili9881c_enable,
+	.disable	= ili9881c_disable,
+	.get_modes	= ili9881c_get_modes,
+};
+
+static int ili9881c_dsi_probe(struct mipi_dsi_device *dsi)
+{
+	struct device_node *np;
+	struct ili9881c *ctx;
+	int ret;
+
+	ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+	mipi_dsi_set_drvdata(dsi, ctx);
+	ctx->dsi = dsi;
+
+	drm_panel_init(&ctx->panel);
+	ctx->panel.dev = &dsi->dev;
+	ctx->panel.funcs = &ili9881c_funcs;
+
+	ctx->power = devm_gpiod_get(&dsi->dev, "power", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->power)) {
+		dev_err(&dsi->dev, "Couldn't get our power GPIO\n");
+		return PTR_ERR(ctx->power);
+	}
+
+	ctx->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(ctx->reset)) {
+		dev_err(&dsi->dev, "Couldn't get our reset GPIO\n");
+		return PTR_ERR(ctx->reset);
+	}
+
+	np = of_parse_phandle(dsi->dev.of_node, "backlight", 0);
+	if (np) {
+		ctx->backlight = of_find_backlight_by_node(np);
+		of_node_put(np);
+
+		if (!ctx->backlight)
+			return -EPROBE_DEFER;
+	}
+
+	ret = drm_panel_add(&ctx->panel);
+	if (ret < 0)
+		return ret;
+
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->lanes = 4;
+
+	return mipi_dsi_attach(dsi);
+}
+
+static int ili9881c_dsi_remove(struct mipi_dsi_device *dsi)
+{
+	struct ili9881c *ctx = mipi_dsi_get_drvdata(dsi);
+
+	mipi_dsi_detach(dsi);
+	drm_panel_remove(&ctx->panel);
+
+	if (ctx->backlight)
+		put_device(&ctx->backlight->dev);
+
+	return 0;
+}
+
+static const struct of_device_id ili9881c_of_match[] = {
+	{ .compatible = "bananapi,lhr050h41" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ili9881c_of_match);
+
+static struct mipi_dsi_driver ili9881c_dsi_driver = {
+	.probe		= ili9881c_dsi_probe,
+	.remove		= ili9881c_dsi_remove,
+	.driver = {
+		.name		= "ili9881c-dsi",
+		.of_match_table	= ili9881c_of_match,
+	},
+};
+module_mipi_dsi_driver(ili9881c_dsi_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
+MODULE_DESCRIPTION("Ilitek ILI9881C Controller Driver");
+MODULE_LICENSE("GPL v2");
-- 
git-series 0.9.1

[PATCH v4 7/8] ARM: dts: sun8i: a33: Add the DSI-related nodes

[Maxime Ripard]

The A33 has a MIPI-DSI block, along with its D-PHY. Let's add it in order
to use it in the relevant boards.

Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 arch/arm/boot/dts/sun8i-a33.dtsi | 44 +++++++++++++++++++++++++++++++++-
 1 file changed, 44 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi
index 50eb84fa246a..10e683997760 100644
--- a/arch/arm/boot/dts/sun8i-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a33.dtsi
@@ -236,6 +236,11 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <1>;
+
+					tcon0_out_dsi: endpoint@1 {
+						reg = <1>;
+						remote-endpoint = <&dsi_in_tcon0>;
+					};
 				};
 			};
 		};
@@ -280,6 +285,45 @@
 			#io-channel-cells = <0>;
 		};
 
+		dsi: dsi@1ca0000 {
+			compatible = "allwinner,sun6i-a31-mipi-dsi";
+			reg = <0x01ca0000 0x1000>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_MIPI_DSI>,
+				 <&ccu CLK_DSI_SCLK>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_MIPI_DSI>;
+			phys = <&dphy>;
+			phy-names = "dphy";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+
+					dsi_in_tcon0: endpoint {
+						remote-endpoint = <&tcon0_out_dsi>;
+					};
+				};
+			};
+		};
+
+		dphy: d-phy@1ca1000 {
+			compatible = "allwinner,sun6i-a31-mipi-dphy";
+			reg = <0x01ca1000 0x1000>;
+			clocks = <&ccu CLK_BUS_MIPI_DSI>,
+				 <&ccu CLK_DSI_DPHY>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_MIPI_DSI>;
+			status = "disabled";
+			#phy-cells = <0>;
+		};
+
 		fe0: display-frontend@1e00000 {
 			compatible = "allwinner,sun8i-a33-display-frontend";
 			reg = <0x01e00000 0x20000>;
-- 
git-series 0.9.1

[PATCH v4 8/8] [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display

[Maxime Ripard]

The BananaPi M2M has an optional 1280x720 DSI panel. Since that panel is
optional, we can only show a DT patch that would show how to enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
---
 arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 39 +++++++++++++++++++++-
 1 file changed, 39 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
index eaf09666720d..30e710e94912 100644
--- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
+++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
@@ -44,6 +44,7 @@
 #include "sun8i-a33.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "BananaPi M2 Magic";
@@ -81,6 +82,14 @@
 		};
 	};
 
+	pwm_bl: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <1 2 4 8 16 32 64 128 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PG10 */
+	};
+
 	reg_vcc5v0: vcc5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc5v0";
@@ -120,6 +129,26 @@
 	status = "okay";
 };
 
+&de {
+	status = "okay";
+};
+
+&dphy {
+	status = "okay";
+};
+
+&dsi {
+	status = "okay";
+
+	panel@0 {
+		compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+		reg = <0>;
+		power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
+		reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
+		backlight = <&pwm_bl>;
+	};
+};
+
 &ehci0 {
 	status = "okay";
 };
@@ -179,6 +208,12 @@
 	status = "okay";
 };
 
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
+
 &r_rsb {
 	status = "okay";
 
@@ -291,6 +326,10 @@
 	status = "okay";
 };
 
+&tcon0 {
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins_b>;
-- 
git-series 0.9.1

Re: [PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 2488 bytes --]

On Wed, Apr 04, 2018 at 11:57:08AM +0200, Maxime Ripard wrote:
> Hi,
> 
> Here is an preliminary version of the MIPI-DSI support for the Allwinner
> SoCs.
> 
> This controller can be found on a number of recent SoCs, such as the
> A31, A33 or the A64.
> 
> Given the sparse documentation, there's a number of obscure areas, but
> the current implementation has been tested with a 4-lanes DSI panel on
> an A33.
> 
> The support is a bit rough around the edges at the time, and some artifacts
> are still shown on the screen for some reasons. Wider testing with
> different display will hopefully nail those down.
> 
> This needs the regmap_mmio_attach_clk, on its way to Linus in 4.17.
> 
> Let me know what you think,
> Maxime
> 
> Changes from v3:
>   - Rebased on top of current drm-misc-next
>   - Switched to SPDX license header
>   - Made the ECC array const
>   - Split the big DSI patch into two, one to add the DSI driver and one to
>     add the TCON bits.
>   - Removed the dithering code
>   - Changed the DT labels to remove the indices
>   - Used sleeps instead of delays in the panel driver
>   - Used the backlight_enable / _disable functions
>   - Added Chen-Yu's Reviewed-by
> 
> Changes from v2:
>   - Added a ports node under the DSI node
>   - Changed the huarui panel driver to an ili9881c driver
>   - Changed the panel vendor to bananapi
>   - Made the init table static in the panel driver
>   - Dropped the huarui vendor patch for the DT doc.
> 
> Changes from v1:
>   - Rebased on 4.16-rc1
>   - Constified a few function arguments and structures
>   - Reworked the DT binding example a bit
>   - Reworked the panel driver to check for DSI return codes, and use DCS
>     helpers when possible
> 
> Maxime Ripard (8):
>   drm/sun4i: tcon: Add TRI finish interrupt for vblank
>   dt-bindings: display: Add Allwinner MIPI-DSI bindings
>   drm/sun4i: Add Allwinner A31 MIPI-DSI controller support
>   drm/sun4i: Tie the DSI controller in the TCON
>   dt-bindings: panel: Add the Ilitek ILI9881c panel documentation
>   drm/panel: Add Ilitek ILI9881c panel driver
>   ARM: dts: sun8i: a33: Add the DSI-related nodes
>   [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display

I just pushed the patches 1-4 and 7. I'll wait for some feedback from
Thierry for the panel driver.

Maxime

-- 
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[Jagan Teki]

On Wed, Apr 11, 2018 at 6:13 PM, Maxime Ripard
<maxime.ripard@bootlin.com> wrote:
> On Wed, Apr 04, 2018 at 11:57:08AM +0200, Maxime Ripard wrote:
>> Hi,
>>
>> Here is an preliminary version of the MIPI-DSI support for the Allwinner
>> SoCs.
>>
>> This controller can be found on a number of recent SoCs, such as the
>> A31, A33 or the A64.
>>
>> Given the sparse documentation, there's a number of obscure areas, but
>> the current implementation has been tested with a 4-lanes DSI panel on
>> an A33.
>>
>> The support is a bit rough around the edges at the time, and some artifacts
>> are still shown on the screen for some reasons. Wider testing with
>> different display will hopefully nail those down.
>>
>> This needs the regmap_mmio_attach_clk, on its way to Linus in 4.17.
>>
>> Let me know what you think,
>> Maxime
>>
>> Changes from v3:
>>   - Rebased on top of current drm-misc-next
>>   - Switched to SPDX license header
>>   - Made the ECC array const
>>   - Split the big DSI patch into two, one to add the DSI driver and one to
>>     add the TCON bits.
>>   - Removed the dithering code
>>   - Changed the DT labels to remove the indices
>>   - Used sleeps instead of delays in the panel driver
>>   - Used the backlight_enable / _disable functions
>>   - Added Chen-Yu's Reviewed-by
>>
>> Changes from v2:
>>   - Added a ports node under the DSI node
>>   - Changed the huarui panel driver to an ili9881c driver
>>   - Changed the panel vendor to bananapi
>>   - Made the init table static in the panel driver
>>   - Dropped the huarui vendor patch for the DT doc.
>>
>> Changes from v1:
>>   - Rebased on 4.16-rc1
>>   - Constified a few function arguments and structures
>>   - Reworked the DT binding example a bit
>>   - Reworked the panel driver to check for DSI return codes, and use DCS
>>     helpers when possible
>>
>> Maxime Ripard (8):
>>   drm/sun4i: tcon: Add TRI finish interrupt for vblank
>>   dt-bindings: display: Add Allwinner MIPI-DSI bindings
>>   drm/sun4i: Add Allwinner A31 MIPI-DSI controller support
>>   drm/sun4i: Tie the DSI controller in the TCON
>>   dt-bindings: panel: Add the Ilitek ILI9881c panel documentation
>>   drm/panel: Add Ilitek ILI9881c panel driver
>>   ARM: dts: sun8i: a33: Add the DSI-related nodes
>>   [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display

I have reviewed most of the patches and reused for A64 all look fine
to me (except the panel driver). May be my issue is not relevant to
this thread, but I'm looking for help If I miss anything for A64 [1]
and [2] are changes made for A64, the issue is kernel hang while
loading sun6i_dsi.

Log:

# modprobe -a sun6i_dsi
[   18.798684] sun6i-mipi-dsi 1ca0000.dsi: Attached device ts8550b
[   18.819628] sun4i-drm display-engine: bound 1100000.mixer (ops
sun8i_mixer_ops)
[   18.827336] sun4i-drm display-engine: No panel or bridge found...
RGB output disabled
[   18.835200] sun4i-drm display-engine: bound 1c0c000.lcd-controller
(ops sun4i_tcon_ops)
[   18.843246] sun4i-drm display-engine: bound 1ca0000.dsi (ops
sun6i_dsi_ops [sun6i_dsi])
[   18.851263] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[   18.857878] [drm] No driver support for vblank timestamp query.

<< hang here >>

[1] https://github.com/openedev/linux-openedev/commit/9030929673b21971ff77b7593e88c26e84ed3742
[2] https://github.com/openedev/linux-openedev/commit/725afe3ce4507fa975fcb4a04b1bbb90d9d44a91

Jagan.

-- 
Jagan Teki
Free Software Engineer | www.openedev.com
U-Boot, Linux | Upstream Maintainer
Hyderabad, India.

Re: [PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 3107 bytes --]

On Fri, Apr 13, 2018 at 05:30:04PM +0530, Jagan Teki wrote:
> On Wed, Apr 11, 2018 at 6:13 PM, Maxime Ripard
> <maxime.ripard@bootlin.com> wrote:
> > On Wed, Apr 04, 2018 at 11:57:08AM +0200, Maxime Ripard wrote:
> >> Hi,
> >>
> >> Here is an preliminary version of the MIPI-DSI support for the Allwinner
> >> SoCs.
> >>
> >> This controller can be found on a number of recent SoCs, such as the
> >> A31, A33 or the A64.
> >>
> >> Given the sparse documentation, there's a number of obscure areas, but
> >> the current implementation has been tested with a 4-lanes DSI panel on
> >> an A33.
> >>
> >> The support is a bit rough around the edges at the time, and some artifacts
> >> are still shown on the screen for some reasons. Wider testing with
> >> different display will hopefully nail those down.
> >>
> >> This needs the regmap_mmio_attach_clk, on its way to Linus in 4.17.
> >>
> >> Let me know what you think,
> >> Maxime
> >>
> >> Changes from v3:
> >>   - Rebased on top of current drm-misc-next
> >>   - Switched to SPDX license header
> >>   - Made the ECC array const
> >>   - Split the big DSI patch into two, one to add the DSI driver and one to
> >>     add the TCON bits.
> >>   - Removed the dithering code
> >>   - Changed the DT labels to remove the indices
> >>   - Used sleeps instead of delays in the panel driver
> >>   - Used the backlight_enable / _disable functions
> >>   - Added Chen-Yu's Reviewed-by
> >>
> >> Changes from v2:
> >>   - Added a ports node under the DSI node
> >>   - Changed the huarui panel driver to an ili9881c driver
> >>   - Changed the panel vendor to bananapi
> >>   - Made the init table static in the panel driver
> >>   - Dropped the huarui vendor patch for the DT doc.
> >>
> >> Changes from v1:
> >>   - Rebased on 4.16-rc1
> >>   - Constified a few function arguments and structures
> >>   - Reworked the DT binding example a bit
> >>   - Reworked the panel driver to check for DSI return codes, and use DCS
> >>     helpers when possible
> >>
> >> Maxime Ripard (8):
> >>   drm/sun4i: tcon: Add TRI finish interrupt for vblank
> >>   dt-bindings: display: Add Allwinner MIPI-DSI bindings
> >>   drm/sun4i: Add Allwinner A31 MIPI-DSI controller support
> >>   drm/sun4i: Tie the DSI controller in the TCON
> >>   dt-bindings: panel: Add the Ilitek ILI9881c panel documentation
> >>   drm/panel: Add Ilitek ILI9881c panel driver
> >>   ARM: dts: sun8i: a33: Add the DSI-related nodes
> >>   [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display
> 
> I have reviewed most of the patches and reused for A64 all look fine
> to me (except the panel driver). May be my issue is not relevant to
> this thread, but I'm looking for help If I miss anything for A64 [1]
> and [2] are changes made for A64, the issue is kernel hang while
> loading sun6i_dsi.

My guess would be that you're not claiming the DE2 SRAM. See:
https://lkml.org/lkml/2018/3/16/1096

Maxime

-- 
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v4 0/8] drm/sun4i: Allwinner MIPI-DSI support

[Jagan Teki]

On Fri, Apr 13, 2018 at 5:39 PM, Maxime Ripard
<maxime.ripard@bootlin.com> wrote:
> On Fri, Apr 13, 2018 at 05:30:04PM +0530, Jagan Teki wrote:
>> On Wed, Apr 11, 2018 at 6:13 PM, Maxime Ripard
>> <maxime.ripard@bootlin.com> wrote:
>> > On Wed, Apr 04, 2018 at 11:57:08AM +0200, Maxime Ripard wrote:
>> >> Hi,
>> >>
>> >> Here is an preliminary version of the MIPI-DSI support for the Allwinner
>> >> SoCs.
>> >>
>> >> This controller can be found on a number of recent SoCs, such as the
>> >> A31, A33 or the A64.
>> >>
>> >> Given the sparse documentation, there's a number of obscure areas, but
>> >> the current implementation has been tested with a 4-lanes DSI panel on
>> >> an A33.
>> >>
>> >> The support is a bit rough around the edges at the time, and some artifacts
>> >> are still shown on the screen for some reasons. Wider testing with
>> >> different display will hopefully nail those down.
>> >>
>> >> This needs the regmap_mmio_attach_clk, on its way to Linus in 4.17.
>> >>
>> >> Let me know what you think,
>> >> Maxime
>> >>
>> >> Changes from v3:
>> >>   - Rebased on top of current drm-misc-next
>> >>   - Switched to SPDX license header
>> >>   - Made the ECC array const
>> >>   - Split the big DSI patch into two, one to add the DSI driver and one to
>> >>     add the TCON bits.
>> >>   - Removed the dithering code
>> >>   - Changed the DT labels to remove the indices
>> >>   - Used sleeps instead of delays in the panel driver
>> >>   - Used the backlight_enable / _disable functions
>> >>   - Added Chen-Yu's Reviewed-by
>> >>
>> >> Changes from v2:
>> >>   - Added a ports node under the DSI node
>> >>   - Changed the huarui panel driver to an ili9881c driver
>> >>   - Changed the panel vendor to bananapi
>> >>   - Made the init table static in the panel driver
>> >>   - Dropped the huarui vendor patch for the DT doc.
>> >>
>> >> Changes from v1:
>> >>   - Rebased on 4.16-rc1
>> >>   - Constified a few function arguments and structures
>> >>   - Reworked the DT binding example a bit
>> >>   - Reworked the panel driver to check for DSI return codes, and use DCS
>> >>     helpers when possible
>> >>
>> >> Maxime Ripard (8):
>> >>   drm/sun4i: tcon: Add TRI finish interrupt for vblank
>> >>   dt-bindings: display: Add Allwinner MIPI-DSI bindings
>> >>   drm/sun4i: Add Allwinner A31 MIPI-DSI controller support
>> >>   drm/sun4i: Tie the DSI controller in the TCON
>> >>   dt-bindings: panel: Add the Ilitek ILI9881c panel documentation
>> >>   drm/panel: Add Ilitek ILI9881c panel driver
>> >>   ARM: dts: sun8i: a33: Add the DSI-related nodes
>> >>   [DO NOT MERGE] arm: dts: sun8i: bpi-m2m: Add DSI display
>>
>> I have reviewed most of the patches and reused for A64 all look fine
>> to me (except the panel driver). May be my issue is not relevant to
>> this thread, but I'm looking for help If I miss anything for A64 [1]
>> and [2] are changes made for A64, the issue is kernel hang while
>> loading sun6i_dsi.
>
> My guess would be that you're not claiming the DE2 SRAM. See:
> https://lkml.org/lkml/2018/3/16/1096

Thanks Maxime, will try.

Re: [PATCH v4 6/8] drm/panel: Add Ilitek ILI9881c panel driver

[Thierry Reding]

[-- Attachment #1: Type: text/plain, Size: 18156 bytes --]

On Wed, Apr 04, 2018 at 11:57:14AM +0200, Maxime Ripard wrote:
> The LHR050H41 panel is the panel shipped with the BananaPi M2-Magic, and is
> based on the Ilitek ILI9881c Controller. Add a driver for it, modelled
> after the other Ilitek controller drivers.
> 
> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
> ---
>  drivers/gpu/drm/panel/Kconfig                 |   9 +-
>  drivers/gpu/drm/panel/Makefile                |   1 +-
>  drivers/gpu/drm/panel/panel-ilitek-ili9881c.c | 489 +++++++++++++++++++-
>  3 files changed, 499 insertions(+)
>  create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
> 
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 25682ff3449a..6020c30a33b3 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -46,6 +46,15 @@ config DRM_PANEL_ILITEK_IL9322
>  	  Say Y here if you want to enable support for Ilitek IL9322
>  	  QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
>  
> +config DRM_PANEL_ILITEK_ILI9881C
> +	tristate "Ilitek ILI9881C-based panels"
> +	depends on OF
> +	depends on DRM_MIPI_DSI
> +	depends on BACKLIGHT_CLASS_DEVICE
> +	help
> +	  Say Y if you want to enable support for panels based on the
> +	  Ilitek ILI9881c controller.
> +
>  config DRM_PANEL_INNOLUX_P079ZCA
>  	tristate "Innolux P079ZCA panel"
>  	depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index f26efc11d746..5ccaaa9d13af 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -3,6 +3,7 @@ obj-$(CONFIG_DRM_PANEL_ARM_VERSATILE) += panel-arm-versatile.o
>  obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
>  obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
>  obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
> +obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
>  obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
>  obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
>  obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
> diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c b/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
> new file mode 100644
> index 000000000000..8992a6431c30
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9881c.c
> @@ -0,0 +1,489 @@
> +// SPDX-License-Identifier: GPL-2.0+

This isn't a valid SPDX license specifier. The module license is GPL v2,
so the corresponding specifier would be: GPL-2.0-only.

> +/*
> + * Copyright (C) 2017, Free Electrons

-2018?

> + * Author: Maxime Ripard <maxime.ripard@free-electrons.com>

No need for this, it's already in MODULE_AUTHOR.

> + */
> +
> +#include <linux/backlight.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/errno.h>
> +#include <linux/fb.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +
> +#include <linux/gpio/consumer.h>
> +
> +#include <drm/drm_mipi_dsi.h>
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +
> +#include <video/mipi_display.h>
> +
> +struct ili9881c {
> +	struct drm_panel	panel;
> +	struct mipi_dsi_device	*dsi;
> +
> +	struct backlight_device *backlight;
> +	struct gpio_desc	*power;
> +	struct gpio_desc	*reset;
> +};
> +
> +enum ili9881c_op {
> +	ILI9881C_SWITCH_PAGE,
> +	ILI9881C_COMMAND,
> +};
> +
> +struct ili9881c_instr {
> +	enum ili9881c_op	op;
> +
> +	union arg {
> +		struct cmd {
> +			u8	cmd;
> +			u8	data;
> +		} cmd;
> +		u8	page;
> +	} arg;
> +};
> +
> +#define ILI9881C_SWITCH_PAGE_INSTR(_page)	\
> +	{					\
> +		.op = ILI9881C_SWITCH_PAGE,	\
> +		.arg = {			\
> +			.page = (_page),	\
> +		},				\
> +	}
> +
> +#define ILI9881C_COMMAND_INSTR(_cmd, _data)		\
> +	{						\
> +		.op = ILI9881C_COMMAND,		\
> +		.arg = {				\
> +			.cmd = {			\
> +				.cmd = (_cmd),		\
> +				.data = (_data),	\
> +			},				\
> +		},					\
> +	}
> +
> +static struct ili9881c_instr ili9881c_init[] = {

These are never modified, so they could be const, right?

> +	ILI9881C_SWITCH_PAGE_INSTR(3),
> +	ILI9881C_COMMAND_INSTR(0x01, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x02, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x03, 0x73),
> +	ILI9881C_COMMAND_INSTR(0x04, 0x03),
> +	ILI9881C_COMMAND_INSTR(0x05, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x06, 0x06),
> +	ILI9881C_COMMAND_INSTR(0x07, 0x06),
> +	ILI9881C_COMMAND_INSTR(0x08, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x09, 0x18),
> +	ILI9881C_COMMAND_INSTR(0x0a, 0x04),
> +	ILI9881C_COMMAND_INSTR(0x0b, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x0c, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x0d, 0x03),
> +	ILI9881C_COMMAND_INSTR(0x0e, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x0f, 0x25),
> +	ILI9881C_COMMAND_INSTR(0x10, 0x25),
> +	ILI9881C_COMMAND_INSTR(0x11, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x12, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x13, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x14, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x15, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x16, 0x0C),
> +	ILI9881C_COMMAND_INSTR(0x17, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x18, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x19, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x1a, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x1b, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x1c, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x1d, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x1e, 0xC0),
> +	ILI9881C_COMMAND_INSTR(0x1f, 0x80),
> +	ILI9881C_COMMAND_INSTR(0x20, 0x04),
> +	ILI9881C_COMMAND_INSTR(0x21, 0x01),
> +	ILI9881C_COMMAND_INSTR(0x22, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x23, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x24, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x25, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x26, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x27, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x28, 0x33),
> +	ILI9881C_COMMAND_INSTR(0x29, 0x03),
> +	ILI9881C_COMMAND_INSTR(0x2a, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x2b, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x2c, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x2d, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x2e, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x2f, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x30, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x31, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x32, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x33, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x34, 0x04),
> +	ILI9881C_COMMAND_INSTR(0x35, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x36, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x37, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x38, 0x3C),
> +	ILI9881C_COMMAND_INSTR(0x39, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3a, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3b, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3c, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3d, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3e, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x3f, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x40, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x41, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x42, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x43, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x44, 0x00),
> +	ILI9881C_COMMAND_INSTR(0x50, 0x01),
> +	ILI9881C_COMMAND_INSTR(0x51, 0x23),
> +	ILI9881C_COMMAND_INSTR(0x52, 0x45),
> +	ILI9881C_COMMAND_INSTR(0x53, 0x67),
> +	ILI9881C_COMMAND_INSTR(0x54, 0x89),
> +	ILI9881C_COMMAND_INSTR(0x55, 0xab),
> +	ILI9881C_COMMAND_INSTR(0x56, 0x01),
> +	ILI9881C_COMMAND_INSTR(0x57, 0x23),
> +	ILI9881C_COMMAND_INSTR(0x58, 0x45),
> +	ILI9881C_COMMAND_INSTR(0x59, 0x67),
> +	ILI9881C_COMMAND_INSTR(0x5a, 0x89),
> +	ILI9881C_COMMAND_INSTR(0x5b, 0xab),
> +	ILI9881C_COMMAND_INSTR(0x5c, 0xcd),
> +	ILI9881C_COMMAND_INSTR(0x5d, 0xef),
> +	ILI9881C_COMMAND_INSTR(0x5e, 0x11),
> +	ILI9881C_COMMAND_INSTR(0x5f, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x60, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x61, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x62, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x63, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x64, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x65, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x66, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x67, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x68, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x69, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x6a, 0x0C),
> +	ILI9881C_COMMAND_INSTR(0x6b, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x6c, 0x0F),
> +	ILI9881C_COMMAND_INSTR(0x6d, 0x0E),
> +	ILI9881C_COMMAND_INSTR(0x6e, 0x0D),
> +	ILI9881C_COMMAND_INSTR(0x6f, 0x06),
> +	ILI9881C_COMMAND_INSTR(0x70, 0x07),
> +	ILI9881C_COMMAND_INSTR(0x71, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x72, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x73, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x74, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x75, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x76, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x77, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x78, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x79, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7a, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7b, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7c, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7d, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7e, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x7f, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x80, 0x0C),
> +	ILI9881C_COMMAND_INSTR(0x81, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x82, 0x0F),
> +	ILI9881C_COMMAND_INSTR(0x83, 0x0E),
> +	ILI9881C_COMMAND_INSTR(0x84, 0x0D),
> +	ILI9881C_COMMAND_INSTR(0x85, 0x06),
> +	ILI9881C_COMMAND_INSTR(0x86, 0x07),
> +	ILI9881C_COMMAND_INSTR(0x87, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x88, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x89, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x8A, 0x02),
> +	ILI9881C_SWITCH_PAGE_INSTR(4),
> +	ILI9881C_COMMAND_INSTR(0x6C, 0x15),
> +	ILI9881C_COMMAND_INSTR(0x6E, 0x22),
> +	ILI9881C_COMMAND_INSTR(0x6F, 0x33),
> +	ILI9881C_COMMAND_INSTR(0x3A, 0xA4),
> +	ILI9881C_COMMAND_INSTR(0x8D, 0x0D),
> +	ILI9881C_COMMAND_INSTR(0x87, 0xBA),
> +	ILI9881C_COMMAND_INSTR(0x26, 0x76),
> +	ILI9881C_COMMAND_INSTR(0xB2, 0xD1),
> +	ILI9881C_SWITCH_PAGE_INSTR(1),
> +	ILI9881C_COMMAND_INSTR(0x22, 0x0A),
> +	ILI9881C_COMMAND_INSTR(0x53, 0xDC),
> +	ILI9881C_COMMAND_INSTR(0x55, 0xA7),
> +	ILI9881C_COMMAND_INSTR(0x50, 0x78),
> +	ILI9881C_COMMAND_INSTR(0x51, 0x78),
> +	ILI9881C_COMMAND_INSTR(0x31, 0x02),
> +	ILI9881C_COMMAND_INSTR(0x60, 0x14),
> +	ILI9881C_COMMAND_INSTR(0xA0, 0x2A),
> +	ILI9881C_COMMAND_INSTR(0xA1, 0x39),
> +	ILI9881C_COMMAND_INSTR(0xA2, 0x46),
> +	ILI9881C_COMMAND_INSTR(0xA3, 0x0e),
> +	ILI9881C_COMMAND_INSTR(0xA4, 0x12),
> +	ILI9881C_COMMAND_INSTR(0xA5, 0x25),
> +	ILI9881C_COMMAND_INSTR(0xA6, 0x19),
> +	ILI9881C_COMMAND_INSTR(0xA7, 0x1d),
> +	ILI9881C_COMMAND_INSTR(0xA8, 0xa6),
> +	ILI9881C_COMMAND_INSTR(0xA9, 0x1C),
> +	ILI9881C_COMMAND_INSTR(0xAA, 0x29),
> +	ILI9881C_COMMAND_INSTR(0xAB, 0x85),
> +	ILI9881C_COMMAND_INSTR(0xAC, 0x1C),
> +	ILI9881C_COMMAND_INSTR(0xAD, 0x1B),
> +	ILI9881C_COMMAND_INSTR(0xAE, 0x51),
> +	ILI9881C_COMMAND_INSTR(0xAF, 0x22),
> +	ILI9881C_COMMAND_INSTR(0xB0, 0x2d),
> +	ILI9881C_COMMAND_INSTR(0xB1, 0x4f),
> +	ILI9881C_COMMAND_INSTR(0xB2, 0x59),
> +	ILI9881C_COMMAND_INSTR(0xB3, 0x3F),
> +	ILI9881C_COMMAND_INSTR(0xC0, 0x2A),
> +	ILI9881C_COMMAND_INSTR(0xC1, 0x3a),
> +	ILI9881C_COMMAND_INSTR(0xC2, 0x45),
> +	ILI9881C_COMMAND_INSTR(0xC3, 0x0e),
> +	ILI9881C_COMMAND_INSTR(0xC4, 0x11),
> +	ILI9881C_COMMAND_INSTR(0xC5, 0x24),
> +	ILI9881C_COMMAND_INSTR(0xC6, 0x1a),
> +	ILI9881C_COMMAND_INSTR(0xC7, 0x1c),
> +	ILI9881C_COMMAND_INSTR(0xC8, 0xaa),
> +	ILI9881C_COMMAND_INSTR(0xC9, 0x1C),
> +	ILI9881C_COMMAND_INSTR(0xCA, 0x29),
> +	ILI9881C_COMMAND_INSTR(0xCB, 0x96),
> +	ILI9881C_COMMAND_INSTR(0xCC, 0x1C),
> +	ILI9881C_COMMAND_INSTR(0xCD, 0x1B),
> +	ILI9881C_COMMAND_INSTR(0xCE, 0x51),
> +	ILI9881C_COMMAND_INSTR(0xCF, 0x22),
> +	ILI9881C_COMMAND_INSTR(0xD0, 0x2b),
> +	ILI9881C_COMMAND_INSTR(0xD1, 0x4b),
> +	ILI9881C_COMMAND_INSTR(0xD2, 0x59),
> +	ILI9881C_COMMAND_INSTR(0xD3, 0x3F),
> +};
> +
> +static inline struct ili9881c *panel_to_ili9881c(struct drm_panel *panel)
> +{
> +	return container_of(panel, struct ili9881c, panel);
> +}
> +
> +static int ili9881c_switch_page(struct ili9881c *ctx, u8 page)
> +{
> +	u8 buf[4] = { 0xff, 0x98, 0x81, page };
> +	int ret;
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, buf, sizeof(buf));
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int ili9881c_send_cmd_data(struct ili9881c *ctx, u8 cmd, u8 data)
> +{
> +	u8 buf[2] = { cmd, data };
> +	int ret;
> +
> +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, buf, sizeof(buf));
> +	if (ret < 0)
> +		return ret;
> +
> +	return 0;
> +}

According to this you're sending DCS commands, but none of the above
look like valid DCS commands. Do you know what's going on here? Also,
can you include a reference to a datasheet where these instructions
come from?

Thierry

> +
> +static int ili9881c_prepare(struct drm_panel *panel)
> +{
> +	struct ili9881c *ctx = panel_to_ili9881c(panel);
> +	unsigned int i;
> +	int ret;
> +
> +	/* Power the panel */
> +	gpiod_set_value(ctx->power, 1);
> +	msleep(5);
> +
> +	/* And reset it */
> +	gpiod_set_value(ctx->reset, 1);
> +	msleep(20);
> +
> +	gpiod_set_value(ctx->reset, 0);
> +	msleep(20);
> +
> +	for (i = 0; i < ARRAY_SIZE(ili9881c_init); i++) {
> +		struct ili9881c_instr *instr = &ili9881c_init[i];
> +
> +		if (instr->op == ILI9881C_SWITCH_PAGE)
> +			ret = ili9881c_switch_page(ctx, instr->arg.page);
> +		else if (instr->op == ILI9881C_COMMAND)
> +			ret = ili9881c_send_cmd_data(ctx, instr->arg.cmd.cmd,
> +						      instr->arg.cmd.data);
> +
> +		if (ret)
> +			return ret;
> +	}
> +
> +	ret = ili9881c_switch_page(ctx, 0);
> +	if (ret)
> +		return ret;
> +
> +	ret = mipi_dsi_dcs_set_tear_on(ctx->dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
> +	if (ret)
> +		return ret;
> +
> +	mipi_dsi_dcs_exit_sleep_mode(ctx->dsi);
> +	if (ret)
> +		return ret;
> +
> +	return 0;
> +}
> +
> +static int ili9881c_enable(struct drm_panel *panel)
> +{
> +	struct ili9881c *ctx = panel_to_ili9881c(panel);
> +
> +	msleep(120);
> +
> +	mipi_dsi_dcs_set_display_on(ctx->dsi);
> +	backlight_enable(ctx->backlight);
> +
> +	return 0;
> +}
> +
> +static int ili9881c_disable(struct drm_panel *panel)
> +{
> +	struct ili9881c *ctx = panel_to_ili9881c(panel);
> +
> +	backlight_disable(ctx->backlight);
> +	return mipi_dsi_dcs_set_display_off(ctx->dsi);
> +}
> +
> +static int ili9881c_unprepare(struct drm_panel *panel)
> +{
> +	struct ili9881c *ctx = panel_to_ili9881c(panel);
> +
> +	mipi_dsi_dcs_enter_sleep_mode(ctx->dsi);
> +	gpiod_set_value(ctx->power, 0);
> +	gpiod_set_value(ctx->reset, 1);
> +
> +	return 0;
> +}
> +
> +static const struct drm_display_mode default_mode = {
> +	.clock		= 62000,
> +	.vrefresh	= 60,
> +
> +	.hdisplay	= 720,
> +	.hsync_start	= 720 + 10,
> +	.hsync_end	= 720 + 10 + 20,
> +	.htotal		= 720 + 10 + 20 + 30,
> +
> +	.vdisplay	= 1280,
> +	.vsync_start	= 1280 + 10,
> +	.vsync_end	= 1280 + 10 + 10,
> +	.vtotal		= 1280 + 10 + 10 + 20,
> +};
> +
> +static int ili9881c_get_modes(struct drm_panel *panel)
> +{
> +	struct drm_connector *connector = panel->connector;
> +	struct ili9881c *ctx = panel_to_ili9881c(panel);
> +	struct drm_display_mode *mode;
> +
> +	mode = drm_mode_duplicate(panel->drm, &default_mode);
> +	if (!mode) {
> +		dev_err(&ctx->dsi->dev, "failed to add mode %ux%ux@%u\n",
> +			default_mode.hdisplay, default_mode.vdisplay,
> +			default_mode.vrefresh);
> +		return -ENOMEM;
> +	}
> +
> +	drm_mode_set_name(mode);
> +
> +	mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> +	drm_mode_probed_add(connector, mode);
> +
> +	panel->connector->display_info.width_mm = 62;
> +	panel->connector->display_info.height_mm = 110;
> +
> +	return 1;
> +}
> +
> +static const struct drm_panel_funcs ili9881c_funcs = {
> +	.prepare	= ili9881c_prepare,
> +	.unprepare	= ili9881c_unprepare,
> +	.enable		= ili9881c_enable,
> +	.disable	= ili9881c_disable,
> +	.get_modes	= ili9881c_get_modes,
> +};
> +
> +static int ili9881c_dsi_probe(struct mipi_dsi_device *dsi)
> +{
> +	struct device_node *np;
> +	struct ili9881c *ctx;
> +	int ret;
> +
> +	ctx = devm_kzalloc(&dsi->dev, sizeof(*ctx), GFP_KERNEL);
> +	if (!ctx)
> +		return -ENOMEM;
> +	mipi_dsi_set_drvdata(dsi, ctx);
> +	ctx->dsi = dsi;
> +
> +	drm_panel_init(&ctx->panel);
> +	ctx->panel.dev = &dsi->dev;
> +	ctx->panel.funcs = &ili9881c_funcs;
> +
> +	ctx->power = devm_gpiod_get(&dsi->dev, "power", GPIOD_OUT_LOW);
> +	if (IS_ERR(ctx->power)) {
> +		dev_err(&dsi->dev, "Couldn't get our power GPIO\n");
> +		return PTR_ERR(ctx->power);
> +	}
> +
> +	ctx->reset = devm_gpiod_get(&dsi->dev, "reset", GPIOD_OUT_LOW);
> +	if (IS_ERR(ctx->reset)) {
> +		dev_err(&dsi->dev, "Couldn't get our reset GPIO\n");
> +		return PTR_ERR(ctx->reset);
> +	}
> +
> +	np = of_parse_phandle(dsi->dev.of_node, "backlight", 0);
> +	if (np) {
> +		ctx->backlight = of_find_backlight_by_node(np);
> +		of_node_put(np);
> +
> +		if (!ctx->backlight)
> +			return -EPROBE_DEFER;
> +	}
> +
> +	ret = drm_panel_add(&ctx->panel);
> +	if (ret < 0)
> +		return ret;
> +
> +	dsi->mode_flags = MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
> +	dsi->format = MIPI_DSI_FMT_RGB888;
> +	dsi->lanes = 4;
> +
> +	return mipi_dsi_attach(dsi);
> +}
> +
> +static int ili9881c_dsi_remove(struct mipi_dsi_device *dsi)
> +{
> +	struct ili9881c *ctx = mipi_dsi_get_drvdata(dsi);
> +
> +	mipi_dsi_detach(dsi);
> +	drm_panel_remove(&ctx->panel);
> +
> +	if (ctx->backlight)
> +		put_device(&ctx->backlight->dev);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id ili9881c_of_match[] = {
> +	{ .compatible = "bananapi,lhr050h41" },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, ili9881c_of_match);
> +
> +static struct mipi_dsi_driver ili9881c_dsi_driver = {
> +	.probe		= ili9881c_dsi_probe,
> +	.remove		= ili9881c_dsi_remove,
> +	.driver = {
> +		.name		= "ili9881c-dsi",
> +		.of_match_table	= ili9881c_of_match,
> +	},
> +};
> +module_mipi_dsi_driver(ili9881c_dsi_driver);
> +
> +MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>");
> +MODULE_DESCRIPTION("Ilitek ILI9881C Controller Driver");
> +MODULE_LICENSE("GPL v2");
> -- 
> git-series 0.9.1

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]

Re: [PATCH v4 6/8] drm/panel: Add Ilitek ILI9881c panel driver

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 967 bytes --]

Hi Thierry,

Thanks for your review, I'll fix the other things you pointed out.

On Thu, Apr 26, 2018 at 05:07:12PM +0200, Thierry Reding wrote:
> > +static int ili9881c_send_cmd_data(struct ili9881c *ctx, u8 cmd, u8 data)
> > +{
> > +	u8 buf[2] = { cmd, data };
> > +	int ret;
> > +
> > +	ret = mipi_dsi_dcs_write_buffer(ctx->dsi, buf, sizeof(buf));
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	return 0;
> > +}
> 
> According to this you're sending DCS commands, but none of the above
> look like valid DCS commands. Do you know what's going on here?

It looks to me that they are custom DCS commands.

> Also, can you include a reference to a datasheet where these
> instructions come from?

I'm not sure an Excel spreadsheet coming from the panel supplier would
be a good thing to include in a driver :)

Maxime

-- 
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]