From: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
To: Neil Armstrong <narmstrong@baylibre.com>
Cc: jbrunet@baylibre.com, linux-amlogic@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-clk@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/2] clk: meson: g12a: add cpu clocks
Date: Fri, 1 Mar 2019 16:21:52 +0100 [thread overview]
Message-ID: <CAFBinCC1b5Q8Y=5qXKJ+B1XBhpo8PGFYHwTEeVTgbXwz7ge3-A@mail.gmail.com> (raw)
In-Reply-To: <20190301102140.7181-3-narmstrong@baylibre.com>
Hi Neil,
it's great to see the progress on G12A!
On Fri, Mar 1, 2019 at 11:22 AM Neil Armstrong <narmstrong@baylibre.com> wrote:
>
> Add the Amlogic G12A Family CPU Clock tree in read/only for now.
>
> The CPU clock can either use the SYS_PLL for > 1GHz frequencies or
> use a couple of div+mux from 1GHz/667MHz/24MHz source with 2 non-glitch
> muxes.
>
> Proper DVFS support will come in a second time.
can you please also mention that this adds various CPU clock
post-dividers (APB, ATB, AXI and CPU trace)?
I don't mind them being int his patchset
disclaimer for my code-review:
- I don't have access to the datasheet so I can't verify if the clock
tree from this patch is correct
- the latest buildroot code with G12A support
(buildroot_openlinux_kernel_4.9_fbdev_20180706) doesn't have proper
names for all clocks
- based on my experience with Meson8* this looks good overall, some
questions and comments below
> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
>
> ---
> drivers/clk/meson/g12a.c | 348 +++++++++++++++++++++++++++++++++++++++
> drivers/clk/meson/g12a.h | 1 +
> 2 files changed, 349 insertions(+)
>
> diff --git a/drivers/clk/meson/g12a.c b/drivers/clk/meson/g12a.c
> index 0e1ce8c03259..4c938f1b8421 100644
> --- a/drivers/clk/meson/g12a.c
> +++ b/drivers/clk/meson/g12a.c
> @@ -150,6 +150,316 @@ static struct clk_regmap g12a_sys_pll = {
> },
> };
>
> +static struct clk_regmap g12a_sys_pll_div16_en = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 24,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "sys_pll_div16_en",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "sys_pll" },
> + .num_parents = 1,
> + /*
> + * This clock is used to debug the sys_pll range
> + * Linux should not change it at runtime
> + */
if we're not supposed to touch this the enable bit, can you switch to
clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> +static struct clk_fixed_factor g12a_sys_pll_div16 = {
> + .mult = 1,
> + .div = 16,
> + .hw.init = &(struct clk_init_data){
> + .name = "sys_pll_div16",
> + .ops = &clk_fixed_factor_ops,
> + .parent_names = (const char *[]){ "sys_pll_div16_en" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn0_sel = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x3,
> + .shift = 0,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn0_sel",
the buildroot code has a variable with the name "p_premux"
I'm not sure what the datasheet states, but maybe this should be
cpu_clk_dyn0_pre_sel
same applies to the corresponding dyn1 clock below
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ IN_PREFIX "xtal",
> + "fclk_div2",
> + "fclk_div3" },
> + .num_parents = 3,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn0_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .shift = 4,
> + .width = 6,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn0_div",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn0_sel" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn0 = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x1,
> + .shift = 2,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn0",
the buildroot code has a variable with the name "p_postmux". in this
case I would leave the name "cpu_clk_dyn0" because it's the "output"
of this specific "clock tree/branch".
same applies to the corresponding dyn1 clock below
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn0_sel",
> + "cpu_clk_dyn0_div" },
> + .num_parents = 2,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn1_sel = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x3,
> + .shift = 16,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn1_sel",
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ IN_PREFIX "xtal",
> + "fclk_div2",
> + "fclk_div3" },
> + .num_parents = 3,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn1_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .shift = 20,
> + .width = 6,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn1_div",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn1_sel" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn1 = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x1,
> + .shift = 18,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn1",
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn1_sel",
> + "cpu_clk_dyn1_div" },
> + .num_parents = 2,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_dyn = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x1,
> + .shift = 10,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_dyn",
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn0",
> + "cpu_clk_dyn1" },
> + .num_parents = 2,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk = {
> + .data = &(struct clk_regmap_mux_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL0,
> + .mask = 0x1,
> + .shift = 11,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk",
> + .ops = &clk_regmap_mux_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk_dyn",
> + "sys_pll" },
> + .num_parents = 2,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_div16_en = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 1,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "cpu_clk_div16_en",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "cpu_clk" },
> + .num_parents = 1,
> + /*
> + * This clock is used to debug the cpu_clk range
> + * Linux should not change it at runtime
> + */
same as above: if we're not supposed to touch this the enable bit, can
you switch to clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> +static struct clk_fixed_factor g12a_cpu_clk_div16 = {
> + .mult = 1,
> + .div = 16,
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_div16",
> + .ops = &clk_fixed_factor_ops,
> + .parent_names = (const char *[]){ "cpu_clk_div16_en" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_apb_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .shift = 3,
> + .width = 3,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_apb_div",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_apb = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 1,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "cpu_clk_apb",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "cpu_clk_apb_div" },
> + .num_parents = 1,
> + /*
> + * This clock is set by the ROM monitor code,
> + * Linux should not change it at runtime
> + */
same as above: if we're not supposed to touch this the enable bit, can
you switch to clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_atb_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .shift = 6,
> + .width = 3,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_atb_div",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_atb = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 17,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "cpu_clk_atb",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "cpu_clk_atb_div" },
> + .num_parents = 1,
> + /*
> + * This clock is set by the ROM monitor code,
> + * Linux should not change it at runtime
> + */
same as above: if we're not supposed to touch this the enable bit, can
you switch to clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_axi_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .shift = 9,
> + .width = 3,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_axi_div",
> + .ops = &clk_regmap_divider_ro_ops,
out of curiosity (this applies to all CPU clock post-dividers):
did you check whether CLK_DIVIDER_POWER_OF_TWO is correct on G12A?
I'm asking because on Meson8b the post-dividers select between one of:
"cpu_clk divided by 2, 3, 4, 5, 6, 7 or 8". also some of the
post-dividers use register value 0 for cpu_clk_div2 while others use
register value 1 for cpu_clk_div2.
> + .parent_names = (const char *[]){ "cpu_clk" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_axi = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 18,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "cpu_clk_axi",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "cpu_clk_axi_div" },
> + .num_parents = 1,
> + /*
> + * This clock is set by the ROM monitor code,
> + * Linux should not change it at runtime
> + */
same as above: if we're not supposed to touch this the enable bit, can
you switch to clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_trace_div = {
> + .data = &(struct clk_regmap_div_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .shift = 20,
> + .width = 3,
> + .flags = CLK_DIVIDER_POWER_OF_TWO,
> + },
> + .hw.init = &(struct clk_init_data){
> + .name = "cpu_clk_trace_div",
> + .ops = &clk_regmap_divider_ro_ops,
> + .parent_names = (const char *[]){ "cpu_clk" },
> + .num_parents = 1,
> + },
> +};
> +
> +static struct clk_regmap g12a_cpu_clk_trace = {
> + .data = &(struct clk_regmap_gate_data){
> + .offset = HHI_SYS_CPU_CLK_CNTL1,
> + .bit_idx = 23,
> + },
> + .hw.init = &(struct clk_init_data) {
> + .name = "cpu_clk_trace",
> + .ops = &clk_regmap_gate_ops,
> + .parent_names = (const char *[]){ "cpu_clk_trace_div" },
> + .num_parents = 1,
> + /*
> + * This clock is set by the ROM monitor code,
> + * Linux should not change it at runtime
> + */
same as above: if we're not supposed to touch this the enable bit, can
you switch to clk_regmap_gate_ro_ops ?
> + .flags = CLK_IGNORE_UNUSED,
> + },
> +};
> +
> static const struct pll_mult_range g12a_gp0_pll_mult_range = {
> .min = 55,
> .max = 255,
> @@ -2167,6 +2477,26 @@ static struct clk_hw_onecell_data g12a_hw_onecell_data = {
> [CLKID_MALI] = &g12a_mali.hw,
> [CLKID_MPLL_5OM_DIV] = &g12a_mpll_50m_div.hw,
> [CLKID_MPLL_5OM] = &g12a_mpll_50m.hw,
> + [CLKID_SYS_PLL_DIV16_EN] = &g12a_sys_pll_div16_en.hw,
> + [CLKID_SYS_PLL_DIV16] = &g12a_sys_pll_div16.hw,
> + [CLKID_CPU_CLK_DYN0_SEL] = &g12a_cpu_clk_dyn0_sel.hw,
> + [CLKID_CPU_CLK_DYN0_DIV] = &g12a_cpu_clk_dyn0_div.hw,
> + [CLKID_CPU_CLK_DYN0] = &g12a_cpu_clk_dyn0.hw,
> + [CLKID_CPU_CLK_DYN1_SEL] = &g12a_cpu_clk_dyn1_sel.hw,
> + [CLKID_CPU_CLK_DYN1_DIV] = &g12a_cpu_clk_dyn1_div.hw,
> + [CLKID_CPU_CLK_DYN1] = &g12a_cpu_clk_dyn1.hw,
> + [CLKID_CPU_CLK_DYN] = &g12a_cpu_clk_dyn.hw,
> + [CLKID_CPU_CLK] = &g12a_cpu_clk.hw,
> + [CLKID_CPU_CLK_DIV16_EN] = &g12a_cpu_clk_div16_en.hw,
> + [CLKID_CPU_CLK_DIV16] = &g12a_cpu_clk_div16.hw,
> + [CLKID_CPU_CLK_APB_DIV] = &g12a_cpu_clk_apb_div.hw,
> + [CLKID_CPU_CLK_APB] = &g12a_cpu_clk_apb.hw,
> + [CLKID_CPU_CLK_ATB_DIV] = &g12a_cpu_clk_atb_div.hw,
> + [CLKID_CPU_CLK_ATB] = &g12a_cpu_clk_atb.hw,
> + [CLKID_CPU_CLK_AXI_DIV] = &g12a_cpu_clk_axi_div.hw,
> + [CLKID_CPU_CLK_AXI] = &g12a_cpu_clk_axi.hw,
> + [CLKID_CPU_CLK_TRACE_DIV] = &g12a_cpu_clk_trace_div.hw,
> + [CLKID_CPU_CLK_TRACE] = &g12a_cpu_clk_trace.hw,
> [NR_CLKS] = NULL,
> },
> .num = NR_CLKS,
> @@ -2335,6 +2665,24 @@ static struct clk_regmap *const g12a_clk_regmaps[] = {
> &g12a_mali_1,
> &g12a_mali,
> &g12a_mpll_50m,
> + &g12a_sys_pll_div16_en,
> + &g12a_cpu_clk_dyn0_sel,
> + &g12a_cpu_clk_dyn0_div,
> + &g12a_cpu_clk_dyn0,
> + &g12a_cpu_clk_dyn1_sel,
> + &g12a_cpu_clk_dyn1_div,
> + &g12a_cpu_clk_dyn1,
> + &g12a_cpu_clk_dyn,
> + &g12a_cpu_clk,
> + &g12a_cpu_clk_div16_en,
> + &g12a_cpu_clk_apb_div,
> + &g12a_cpu_clk_apb,
> + &g12a_cpu_clk_atb_div,
> + &g12a_cpu_clk_atb,
> + &g12a_cpu_clk_axi_div,
> + &g12a_cpu_clk_axi,
> + &g12a_cpu_clk_trace_div,
> + &g12a_cpu_clk_trace,
> };
>
> static const struct meson_eeclkc_data g12a_clkc_data = {
> diff --git a/drivers/clk/meson/g12a.h b/drivers/clk/meson/g12a.h
> index 4854750df902..0ba3bfe4d46d 100644
> --- a/drivers/clk/meson/g12a.h
> +++ b/drivers/clk/meson/g12a.h
> @@ -50,6 +50,7 @@
> #define HHI_GCLK_MPEG2 0x148
> #define HHI_GCLK_OTHER 0x150
> #define HHI_GCLK_OTHER2 0x154
> +#define HHI_SYS_CPU_CLK_CNTL1 0x15c
> #define HHI_VID_CLK_DIV 0x164
> #define HHI_MPEG_CLK_CNTL 0x174
> #define HHI_AUD_CLK_CNTL 0x178
> --
> 2.20.1
>
>
> _______________________________________________
> linux-amlogic mailing list
> linux-amlogic@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-03-01 15:22 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-03-01 10:21 [PATCH 0/2] clk: meson: g12a: Add CPU Clock support Neil Armstrong
2019-03-01 10:21 ` [PATCH 1/2] clk: meson-g12a: add cpu clock bindings Neil Armstrong
2019-03-01 15:26 ` Martin Blumenstingl
2019-03-01 16:43 ` Neil Armstrong
2019-03-01 17:05 ` Martin Blumenstingl
2019-03-01 10:21 ` [PATCH 2/2] clk: meson: g12a: add cpu clocks Neil Armstrong
2019-03-01 15:21 ` Martin Blumenstingl [this message]
2019-03-01 16:41 ` Neil Armstrong
2019-03-01 16:52 ` Martin Blumenstingl
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAFBinCC1b5Q8Y=5qXKJ+B1XBhpo8PGFYHwTEeVTgbXwz7ge3-A@mail.gmail.com' \
--to=martin.blumenstingl@googlemail.com \
--cc=jbrunet@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).