From: Amit Kucheria <amit.kucheria@linaro.org>
To: Ilia Lin <ilialin@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>,
sboyd@kernel.org, Rob Herring <robh@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Viresh Kumar <viresh.kumar@linaro.org>,
nm@ti.com, lgirdwood@gmail.com, broonie@kernel.org,
Andy Gross <andy.gross@linaro.org>,
David Brown <david.brown@linaro.org>,
catalin.marinas@arm.com, will.deacon@arm.com,
"Rafael J. Wysocki" <rjw@rjwysocki.net>,
linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
LKML <linux-kernel@vger.kernel.org>,
Linux PM list <linux-pm@vger.kernel.org>,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
lakml <linux-arm-kernel@lists.infradead.org>,
Rajendra Nayak <rnayak@codeaurora.org>,
nicolas.dechesne@linaro.org, celster@codeaurora.org,
tfinkel@codeaurora.org
Subject: Re: [PATCH v7 13/14] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
Date: Wed, 16 May 2018 16:12:27 +0300 [thread overview]
Message-ID: <CAHLCerMivA_3sJUAg8syyiP=63SFkZoTb7rPLhG0m2BX39QLOg@mail.gmail.com> (raw)
In-Reply-To: <1526375616-16904-14-git-send-email-ilialin@codeaurora.org>
On Tue, May 15, 2018 at 12:13 PM, Ilia Lin <ilialin@codeaurora.org> wrote:
> In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
> that have KRYO processors, the CPU ferequencies subset and voltage value
s/ferequencies/frequency
> of each OPP varies based on the silicon variant in use.
> Qualcomm Technologies, Inc. Process Voltage Scaling Tables
> defines the voltage and frequency value based on the msm-id in SMEM
> and speedbin blown in the efuse combination.
> The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> to provide the OPP framework with required information.
> This is used to determine the voltage and frequency value for each OPP of
> operating-points-v2 table when it is parsed by the OPP framework.
>
> This change adds documentation.
Change this to actually document the extension of the op-v2 binding
with a list of compatible HW.
> Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> ---
> .../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
> 1 file changed, 680 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
>
> diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
> new file mode 100644
> index 0000000..c2127b9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
> @@ -0,0 +1,680 @@
> +Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
> +===================================
> +
> +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
> +that have KRYO processors, the CPU ferequencies subset and voltage value
> +of each OPP varies based on the silicon variant in use.
> +Qualcomm Technologies, Inc. Process Voltage Scaling Tables
> +defines the voltage and frequency value based on the msm-id in SMEM
> +and speedbin blown in the efuse combination.
> +The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
> +to provide the OPP framework with required information (existing HW bitmap).
> +This is used to determine the voltage and frequency value for each OPP of
> +operating-points-v2 table when it is parsed by the OPP framework.
> +
> +Required properties:
> +--------------------
> +In 'cpus' nodes:
> +- operating-points-v2: Phandle to the operating-points-v2 table to use.
> +
> +In 'operating-points-v2' table:
> +- compatible: Should be
> + - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
> +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
> + efuse registers that has information about the
> + speedbin that is used to select the right frequency/voltage
> + value pair.
> + Please refer the for nvmem-cells
> + bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
> + and also examples below.
> +
> +In every OPP node:
> +- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
> + Bitmap:
> + 0: MSM8996 V3, speedbin 0
> + 1: MSM8996 V3, speedbin 1
> + 2: MSM8996 V3, speedbin 2
> + 3: unused
> + 4: MSM8996 SG, speedbin 0
> + 5: MSM8996 SG, speedbin 1
> + 6: MSM8996 SG, speedbin 2
> + 7-31: unused
> +
> +Example 1:
> +---------
> +
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + CPU0: cpu@0 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x0>;
> + enable-method = "psci";
> + clocks = <&kryocc 0>;
> + cpu-supply = <&pm8994_s11_saw>;
> + operating-points-v2 = <&cluster0_opp>;
> + #cooling-cells = <2>;
> + next-level-cache = <&L2_0>;
> + L2_0: l2-cache {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + CPU1: cpu@1 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x1>;
> + enable-method = "psci";
> + clocks = <&kryocc 0>;
> + cpu-supply = <&pm8994_s11_saw>;
> + operating-points-v2 = <&cluster0_opp>;
> + #cooling-cells = <2>;
> + next-level-cache = <&L2_0>;
> + };
> +
> + CPU2: cpu@100 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x100>;
> + enable-method = "psci";
> + clocks = <&kryocc 1>;
> + cpu-supply = <&pm8994_s11_saw>;
> + operating-points-v2 = <&cluster1_opp>;
> + #cooling-cells = <2>;
> + next-level-cache = <&L2_1>;
> + L2_1: l2-cache {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> +
> + CPU3: cpu@101 {
> + device_type = "cpu";
> + compatible = "qcom,kryo";
> + reg = <0x0 0x101>;
> + enable-method = "psci";
> + clocks = <&kryocc 1>;
> + cpu-supply = <&pm8994_s11_saw>;
> + operating-points-v2 = <&cluster1_opp>;
> + #cooling-cells = <2>;
> + next-level-cache = <&L2_1>;
> + };
> +
> + cpu-map {
> + cluster0 {
> + core0 {
> + cpu = <&CPU0>;
> + };
> +
> + core1 {
> + cpu = <&CPU1>;
> + };
> + };
> +
> + cluster1 {
> + core0 {
> + cpu = <&CPU2>;
> + };
> +
> + core1 {
> + cpu = <&CPU3>;
> + };
> + };
> + };
> + };
> +
> + cluster0_opp: opp_table0 {
> + compatible = "operating-points-v2-kryo-cpu";
> + nvmem-cells = <&speedbin_efuse>;
> + opp-shared;
> +
> + opp-307200000 {
> + opp-hz = /bits/ 64 <307200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x77>;
> + clock-latency-ns = <200000>;
> + };
> + opp-384000000 {
> + opp-hz = /bits/ 64 <384000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-422400000 {
> + opp-hz = /bits/ 64 <422400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-460800000 {
> + opp-hz = /bits/ 64 <460800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-480000000 {
> + opp-hz = /bits/ 64 <480000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-537600000 {
> + opp-hz = /bits/ 64 <537600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-556800000 {
> + opp-hz = /bits/ 64 <556800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-614400000 {
> + opp-hz = /bits/ 64 <614400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-652800000 {
> + opp-hz = /bits/ 64 <652800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-691200000 {
> + opp-hz = /bits/ 64 <691200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-729600000 {
> + opp-hz = /bits/ 64 <729600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-768000000 {
> + opp-hz = /bits/ 64 <768000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-844800000 {
> + opp-hz = /bits/ 64 <844800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x77>;
> + clock-latency-ns = <200000>;
> + };
> + opp-902400000 {
> + opp-hz = /bits/ 64 <902400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-960000000 {
> + opp-hz = /bits/ 64 <960000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-979200000 {
> + opp-hz = /bits/ 64 <979200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1036800000 {
> + opp-hz = /bits/ 64 <1036800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1056000000 {
> + opp-hz = /bits/ 64 <1056000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1113600000 {
> + opp-hz = /bits/ 64 <1113600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1132800000 {
> + opp-hz = /bits/ 64 <1132800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1190400000 {
> + opp-hz = /bits/ 64 <1190400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1209600000 {
> + opp-hz = /bits/ 64 <1209600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1228800000 {
> + opp-hz = /bits/ 64 <1228800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1286400000 {
> + opp-hz = /bits/ 64 <1286400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1324800000 {
> + opp-hz = /bits/ 64 <1324800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x5>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1363200000 {
> + opp-hz = /bits/ 64 <1363200000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x72>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1401600000 {
> + opp-hz = /bits/ 64 <1401600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x5>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1440000000 {
> + opp-hz = /bits/ 64 <1440000000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1478400000 {
> + opp-hz = /bits/ 64 <1478400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x1>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1497600000 {
> + opp-hz = /bits/ 64 <1497600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x4>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1516800000 {
> + opp-hz = /bits/ 64 <1516800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1593600000 {
> + opp-hz = /bits/ 64 <1593600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x71>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1996800000 {
> + opp-hz = /bits/ 64 <1996800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x20>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2188800000 {
> + opp-hz = /bits/ 64 <2188800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x10>;
> + clock-latency-ns = <200000>;
> + };
> + };
> +
> + cluster1_opp: opp_table1 {
> + compatible = "operating-points-v2-kryo-cpu";
> + nvmem-cells = <&speedbin_efuse>;
> + opp-shared;
> +
> + opp-307200000 {
> + opp-hz = /bits/ 64 <307200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x77>;
> + clock-latency-ns = <200000>;
> + };
> + opp-384000000 {
> + opp-hz = /bits/ 64 <384000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-403200000 {
> + opp-hz = /bits/ 64 <403200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-460800000 {
> + opp-hz = /bits/ 64 <460800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-480000000 {
> + opp-hz = /bits/ 64 <480000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-537600000 {
> + opp-hz = /bits/ 64 <537600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-556800000 {
> + opp-hz = /bits/ 64 <556800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-614400000 {
> + opp-hz = /bits/ 64 <614400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-652800000 {
> + opp-hz = /bits/ 64 <652800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-691200000 {
> + opp-hz = /bits/ 64 <691200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-729600000 {
> + opp-hz = /bits/ 64 <729600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-748800000 {
> + opp-hz = /bits/ 64 <748800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-806400000 {
> + opp-hz = /bits/ 64 <806400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-825600000 {
> + opp-hz = /bits/ 64 <825600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-883200000 {
> + opp-hz = /bits/ 64 <883200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-902400000 {
> + opp-hz = /bits/ 64 <902400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-940800000 {
> + opp-hz = /bits/ 64 <940800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-979200000 {
> + opp-hz = /bits/ 64 <979200000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1036800000 {
> + opp-hz = /bits/ 64 <1036800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1056000000 {
> + opp-hz = /bits/ 64 <1056000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1113600000 {
> + opp-hz = /bits/ 64 <1113600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1132800000 {
> + opp-hz = /bits/ 64 <1132800000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1190400000 {
> + opp-hz = /bits/ 64 <1190400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1209600000 {
> + opp-hz = /bits/ 64 <1209600000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1248000000 {
> + opp-hz = /bits/ 64 <1248000000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1286400000 {
> + opp-hz = /bits/ 64 <1286400000>;
> + opp-microvolt = <905000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1324800000 {
> + opp-hz = /bits/ 64 <1324800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1363200000 {
> + opp-hz = /bits/ 64 <1363200000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1401600000 {
> + opp-hz = /bits/ 64 <1401600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1440000000 {
> + opp-hz = /bits/ 64 <1440000000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1478400000 {
> + opp-hz = /bits/ 64 <1478400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1516800000 {
> + opp-hz = /bits/ 64 <1516800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1555200000 {
> + opp-hz = /bits/ 64 <1555200000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1593600000 {
> + opp-hz = /bits/ 64 <1593600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1632000000 {
> + opp-hz = /bits/ 64 <1632000000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1670400000 {
> + opp-hz = /bits/ 64 <1670400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1708800000 {
> + opp-hz = /bits/ 64 <1708800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1747200000 {
> + opp-hz = /bits/ 64 <1747200000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x70>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1785600000 {
> + opp-hz = /bits/ 64 <1785600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x7>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1804800000 {
> + opp-hz = /bits/ 64 <1804800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x6>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1824000000 {
> + opp-hz = /bits/ 64 <1824000000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x71>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1900800000 {
> + opp-hz = /bits/ 64 <1900800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x74>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1920000000 {
> + opp-hz = /bits/ 64 <1920000000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x1>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1977600000 {
> + opp-hz = /bits/ 64 <1977600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x30>;
> + clock-latency-ns = <200000>;
> + };
> + opp-1996800000 {
> + opp-hz = /bits/ 64 <1996800000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x1>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2054400000 {
> + opp-hz = /bits/ 64 <2054400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x30>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2073600000 {
> + opp-hz = /bits/ 64 <2073600000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x1>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2150400000 {
> + opp-hz = /bits/ 64 <2150400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x31>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2246400000 {
> + opp-hz = /bits/ 64 <2246400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x10>;
> + clock-latency-ns = <200000>;
> + };
> + opp-2342400000 {
> + opp-hz = /bits/ 64 <2342400000>;
> + opp-microvolt = <1140000 905000 1140000>;
> + opp-supported-hw = <0x10>;
> + clock-latency-ns = <200000>;
> + };
> + };
> +
> +....
> +
> +reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +....
> + smem_mem: smem-mem@86000000 {
> + reg = <0x0 0x86000000 0x0 0x200000>;
> + no-map;
> + };
> +....
> +};
> +
> +smem {
> + compatible = "qcom,smem";
> + memory-region = <&smem_mem>;
> + hwlocks = <&tcsr_mutex 3>;
> +};
> +
> +soc {
> +....
> + qfprom: qfprom@74000 {
> + compatible = "qcom,qfprom";
> + reg = <0x00074000 0x8ff>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ....
> + speedbin_efuse: speedbin@133 {
> + reg = <0x133 0x1>;
> + bits = <5 3>;
> + };
> + };
> +};
> --
> 1.9.1
>
next prev parent reply other threads:[~2018-05-16 13:12 UTC|newest]
Thread overview: 34+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-15 9:13 [PATCH v7 00/14] CPU scaling support for msm8996 Ilia Lin
2018-05-15 9:13 ` [PATCH v7 01/14] soc: qcom: Separate kryo l2 accessors from PMU driver Ilia Lin
2018-05-16 13:12 ` Amit Kucheria
2018-05-15 9:13 ` [PATCH v7 02/14] clk: qcom: Make clk_alpha_pll_configure available to modules Ilia Lin
2018-05-15 9:13 ` [PATCH v7 03/14] clk: qcom: Add CPU clock driver for msm8996 Ilia Lin
2018-05-16 13:12 ` Amit Kucheria
2018-05-17 16:31 ` kbuild test robot
2018-05-17 16:51 ` kbuild test robot
2018-05-15 9:13 ` [PATCH v7 04/14] clk: qcom: Add DT bindings for " Ilia Lin
2018-05-15 9:13 ` [PATCH v7 05/14] clk: qcom: cpu-8996: Add support to switch to alternate PLL Ilia Lin
2018-05-15 9:13 ` [PATCH v7 06/14] clk: qcom: cpu-8996: Add support to switch below 600Mhz Ilia Lin
2018-05-15 9:13 ` [PATCH v7 07/14] clk: qcom: Add ACD path to CPU clock driver for msm8996 Ilia Lin
2018-05-15 9:13 ` [PATCH v7 08/14] dt: qcom: Add opp and thermal to the msm8996 Ilia Lin
2018-05-15 9:13 ` [PATCH v7 09/14] regulator: qcom_spmi: Add support for SAW Ilia Lin
2018-05-15 9:13 ` [PATCH v7 10/14] dt-bindings: qcom_spmi: Add support for SAW documentation Ilia Lin
2018-05-16 13:12 ` Amit Kucheria
2018-05-17 7:24 ` ilialin
2018-05-15 9:13 ` [PATCH v7 11/14] dt: qcom: Add SAW regulator for 8x96 CPUs Ilia Lin
2018-05-15 9:13 ` [PATCH v7 12/14] cpufreq: Add Kryo CPU scaling driver Ilia Lin
2018-05-15 9:19 ` Viresh Kumar
2018-05-15 9:28 ` Rafael J. Wysocki
2018-05-16 4:13 ` kbuild test robot
2018-05-16 13:12 ` Amit Kucheria
2018-05-16 14:11 ` Viresh Kumar
2018-05-16 14:13 ` Amit Kucheria
2018-05-17 7:50 ` ilialin
2018-05-17 8:20 ` ilialin
2018-05-17 7:19 ` ilialin
2018-05-15 9:13 ` [PATCH v7 13/14] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu Ilia Lin
2018-05-16 13:12 ` Amit Kucheria [this message]
2018-05-15 9:13 ` [PATCH v7 14/14] dt: qcom: Add qcom-cpufreq-kryo driver configuration Ilia Lin
2018-05-15 9:19 ` Viresh Kumar
2018-05-16 13:12 ` Amit Kucheria
2018-05-16 13:11 ` [PATCH v7 00/14] CPU scaling support for msm8996 Amit Kucheria
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAHLCerMivA_3sJUAg8syyiP=63SFkZoTb7rPLhG0m2BX39QLOg@mail.gmail.com' \
--to=amit.kucheria@linaro.org \
--cc=andy.gross@linaro.org \
--cc=broonie@kernel.org \
--cc=catalin.marinas@arm.com \
--cc=celster@codeaurora.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=ilialin@codeaurora.org \
--cc=lgirdwood@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=nicolas.dechesne@linaro.org \
--cc=nm@ti.com \
--cc=rjw@rjwysocki.net \
--cc=rnayak@codeaurora.org \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=tfinkel@codeaurora.org \
--cc=viresh.kumar@linaro.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).