[PATCH v4 0/3] Add ilitek ili9341 panel driver

[PATCH v4 0/3] Add ilitek ili9341 panel driver

[dillon.minfei]

From: Dillon Min <dillon.minfei@gmail.com>

Since the st,sf-tc240t-9370-t dts binding already exist in stm32f429-disco.dts
but, the panel driver didn't get accepted from mainline. it's time to submit
patch fot it.

This driver can support two different interface by different dts bindings:
- spi+dpi, use spi to configure register, dpi for graphic data.
  st,sf-tc240t-9370-t
- only spi, just like tiny/ili9341.c (actually, this part is copy from tiny)
  adafruit,yx240qv29

I was submited the first patch last year, you can find it at [1].
this patch has one major difference from that one, which is replace the low
level communication way, from spi_sync() to mipi_dbi_{command,
command_stackbuf}() interface, referred from Linus's patch [2].

both the two dpi/dbi interface was tested on stm32f429-disco board, if anyone
want to verify this patch, you need apply the clk patch for this board first,
you can get it from [3].

[1] "drm/panel: Add ilitek ili9341 panel driver"
https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@gmail.com/

[2] "drm/panel: s6e63m0: Switch to DBI abstraction for SPI"
https://lore.kernel.org/dri-devel/20210611214243.669892-1-linus.walleij@linaro.org/

[3]
https://lore.kernel.org/lkml/1590378348-8115-6-git-send-email-dillon.minfei@gmail.com/

v4:
- fix m68k-allmodconfig build error which reported by lkp, thanks.
- add Copyright 2018 David Lechner <david@lechnology.com>.
v3 link:
https://lore.kernel.org/lkml/1627013203-23099-1-git-send-email-dillon.minfei@gmail.com/

v3:
- add Fixes tags.
- collect reviewed-by tags from linus and jagan.
- replace DRM_ERROR() with dev_err() or drm_err().
- remove kernel-doc markers from struct ili9341_config{}.
- reorder include headers.
- remove the struct device *dev from struct ili9341{}.
- restructure the ili9341_probe() function, add two ili9341_{dbi,dpi)_probe()
  to make it more readable according to jagan's suggestion, thanks.

for the full drm driver exist in drm/panel need Sam and Laurent's feedback.
so, not cover this part at this time, will be update later.

v2 link:
https://lore.kernel.org/lkml/1626853288-31223-1-git-send-email-dillon.minfei@gmail.com/

v2:
- replace vcc regulator to bulk regulators in driver, from linus suggestion.
- fix dtbs_check warnings on ili9341 dts binding check.
- add bulk regulation node in ilitek,ili9341.yaml.
v1 link:
https://lore.kernel.org/lkml/1626430843-23823-1-git-send-email-dillon.minfei@gmail.com/

Dillon Min (3):
  dt-bindings: display: panel: Add ilitek ili9341 panel bindings
  ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding
  drm/panel: Add ilitek ili9341 panel driver

 .../bindings/display/panel/ilitek,ili9341.yaml     |  78 ++
 arch/arm/boot/dts/stm32f429-disco.dts              |   2 +-
 drivers/gpu/drm/panel/Kconfig                      |  12 +
 drivers/gpu/drm/panel/Makefile                     |   1 +
 drivers/gpu/drm/panel/panel-ilitek-ili9341.c       | 792 +++++++++++++++++++++
 5 files changed, 884 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c

-- 
1.9.1

[PATCH v4 1/3] dt-bindings: display: panel: Add ilitek ili9341 panel bindings

[dillon.minfei]

From: Dillon Min <dillon.minfei@gmail.com>

Add documentation for "ilitek,ili9341" panel.

Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/lkml/1626853288-31223-2-git-send-email-dillon.minfei@gmail.com/
---
v4: no change.

 .../bindings/display/panel/ilitek,ili9341.yaml     | 78 ++++++++++++++++++++++
 1 file changed, 78 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
new file mode 100644
index 000000000000..2ed010f91e2d
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
@@ -0,0 +1,78 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ilitek,ili9341.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ilitek-9341 Display Panel
+
+maintainers:
+  - Dillon Min <dillon.minfei@gmail.com>
+
+description: |
+  Ilitek ILI9341 TFT panel driver with SPI control bus
+  This is a driver for 320x240 TFT panels, accepting a rgb input
+  streams with 16 bits or 18 bits.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          # ili9341 240*320 Color on stm32f429-disco board
+        - st,sf-tc240t-9370-t
+      - const: ilitek,ili9341
+
+  reg: true
+
+  dc-gpios:
+    maxItems: 1
+    description: Display data/command selection (D/CX) of this DBI panel
+
+  spi-3wire: true
+
+  spi-max-frequency:
+    const: 10000000
+
+  port: true
+
+  vci-supply:
+    description: Analog voltage supply (2.5 .. 3.3V)
+
+  vddi-supply:
+    description: Voltage supply for interface logic (1.65 .. 3.3 V)
+
+  vddi-led-supply:
+    description: Voltage supply for the LED driver (1.65 .. 3.3 V)
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - dc-gpios
+  - port
+
+examples:
+  - |+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        panel: display@0 {
+                 compatible = "st,sf-tc240t-9370-t",
+                              "ilitek,ili9341";
+                 reg = <0>;
+                 spi-3wire;
+                 spi-max-frequency = <10000000>;
+                 dc-gpios = <&gpiod 13 0>;
+                 port {
+                         panel_in: endpoint {
+                           remote-endpoint = <&display_out>;
+                      };
+                 };
+             };
+        };
+...
+
-- 
1.9.1

[PATCH v4 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding

[dillon.minfei]

From: Dillon Min <dillon.minfei@gmail.com>

Since the compatible string defined from ilitek,ili9341.yaml is
"st,sf-tc240t-9370-t", "ilitek,ili9341"

so, append "ilitek,ili9341" to avoid the below dtbs_check warning.

arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
['st,sf-tc240t-9370-t'] is too short

Fixes: a726e2f000ec ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
---
v4: no change.

 arch/arm/boot/dts/stm32f429-disco.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
index 075ac57d0bf4..6435e099c632 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -192,7 +192,7 @@
 
 	display: display@1{
 		/* Connect panel-ilitek-9341 to ltdc */
-		compatible = "st,sf-tc240t-9370-t";
+		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
 		reg = <1>;
 		spi-3wire;
 		spi-max-frequency = <10000000>;
-- 
1.9.1

[PATCH v4 3/3] drm/panel: Add ilitek ili9341 panel driver

[dillon.minfei]

From: Dillon Min <dillon.minfei@gmail.com>

This driver combines tiny/ili9341.c mipi_dbi_interface driver
with mipi_dpi_interface driver, can support ili9341 with serial
mode and parallel rgb interface mode by different dts bindings.

Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
---
v4:
- fix m68k-allmodconfig build error which reported by lkp, thanks.
- add Copyright 2018 David Lechner <david@lechnology.com>.

 drivers/gpu/drm/panel/Kconfig                |  12 +
 drivers/gpu/drm/panel/Makefile               |   1 +
 drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 792 +++++++++++++++++++++++++++
 3 files changed, 805 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index ef87d92cdf49..eb34b8d1b19a 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -124,6 +124,18 @@ config DRM_PANEL_ILITEK_IL9322
 	  Say Y here if you want to enable support for Ilitek IL9322
 	  QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
 
+config DRM_PANEL_ILITEK_ILI9341
+	tristate "Ilitek ILI9341 240x320 QVGA panels"
+	depends on OF && SPI
+	depends on DRM_KMS_HELPER
+	depends on DRM_KMS_CMA_HELPER
+	depends on BACKLIGHT_CLASS_DEVICE
+	select DRM_MIPI_DBI
+	help
+	  Say Y here if you want to enable support for Ilitek IL9341
+	  QVGA (240x320) RGB panels. support serial & parallel rgb
+	  interface.
+
 config DRM_PANEL_ILITEK_ILI9881C
 	tristate "Ilitek ILI9881C-based panels"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index cae4d976c069..0ecde184665d 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
 obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
+obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
 obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
 obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
new file mode 100644
index 000000000000..2c3378a259b1
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
@@ -0,0 +1,792 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Ilitek ILI9341 TFT LCD drm_panel driver.
+ *
+ * This panel can be configured to support:
+ * - 16-bit parallel RGB interface
+ * - 18-bit parallel RGB interface
+ * - 4-line serial spi interface
+ *
+ * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com>
+ *
+ * For dbi+dpi part:
+ * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
+ * the reuse of DBI abstraction part referred from Linus's patch
+ * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI"
+ *
+ * For only-dbi part, copy from David's code (drm/tiny/ili9341.c)
+ * Copyright 2018 David Lechner <david@lechnology.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+
+#include <video/mipi_display.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_drv.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_atomic_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_mipi_dbi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#define ILI9341_RGB_INTERFACE  0xb0   /* RGB Interface Signal Control */
+#define ILI9341_FRC            0xb1   /* Frame Rate Control register */
+#define ILI9341_DFC            0xb6   /* Display Function Control register */
+#define ILI9341_POWER1         0xc0   /* Power Control 1 register */
+#define ILI9341_POWER2         0xc1   /* Power Control 2 register */
+#define ILI9341_VCOM1          0xc5   /* VCOM Control 1 register */
+#define ILI9341_VCOM2          0xc7   /* VCOM Control 2 register */
+#define ILI9341_POWERA         0xcb   /* Power control A register */
+#define ILI9341_POWERB         0xcf   /* Power control B register */
+#define ILI9341_PGAMMA         0xe0   /* Positive Gamma Correction register */
+#define ILI9341_NGAMMA         0xe1   /* Negative Gamma Correction register */
+#define ILI9341_DTCA           0xe8   /* Driver timing control A */
+#define ILI9341_DTCB           0xea   /* Driver timing control B */
+#define ILI9341_POWER_SEQ      0xed   /* Power on sequence register */
+#define ILI9341_3GAMMA_EN      0xf2   /* 3 Gamma enable register */
+#define ILI9341_INTERFACE      0xf6   /* Interface control register */
+#define ILI9341_PRC            0xf7   /* Pump ratio control register */
+#define ILI9341_ETMOD	       0xb7   /* Entry mode set */
+
+#define ILI9341_MADCTL_BGR	BIT(3)
+#define ILI9341_MADCTL_MV	BIT(5)
+#define ILI9341_MADCTL_MX	BIT(6)
+#define ILI9341_MADCTL_MY	BIT(7)
+
+#define ILI9341_POWER_B_LEN	3
+#define ILI9341_POWER_SEQ_LEN	4
+#define ILI9341_DTCA_LEN	3
+#define ILI9341_DTCB_LEN	2
+#define ILI9341_POWER_A_LEN	5
+#define ILI9341_DFC_1_LEN	2
+#define ILI9341_FRC_LEN		2
+#define ILI9341_VCOM_1_LEN	2
+#define ILI9341_DFC_2_LEN	4
+#define ILI9341_COLUMN_ADDR_LEN	4
+#define ILI9341_PAGE_ADDR_LEN	4
+#define ILI9341_INTERFACE_LEN	3
+#define ILI9341_PGAMMA_LEN	15
+#define ILI9341_NGAMMA_LEN	15
+#define ILI9341_CA_LEN		3
+
+#define ILI9341_PIXEL_DPI_16_BITS	(BIT(6) | BIT(4))
+#define ILI9341_PIXEL_DPI_18_BITS	(BIT(6) | BIT(5))
+#define ILI9341_GAMMA_CURVE_1		BIT(0)
+#define ILI9341_IF_WE_MODE		BIT(0)
+#define ILI9341_IF_BIG_ENDIAN		0x00
+#define ILI9341_IF_DM_RGB		BIT(2)
+#define ILI9341_IF_DM_INTERNAL		0x00
+#define ILI9341_IF_DM_VSYNC		BIT(3)
+#define ILI9341_IF_RM_RGB		BIT(1)
+#define ILI9341_IF_RIM_RGB		0x00
+
+#define ILI9341_COLUMN_ADDR		0x00ef
+#define ILI9341_PAGE_ADDR		0x013f
+
+#define ILI9341_RGB_EPL			BIT(0)
+#define ILI9341_RGB_DPL			BIT(1)
+#define ILI9341_RGB_HSPL		BIT(2)
+#define ILI9341_RGB_VSPL		BIT(3)
+#define ILI9341_RGB_DE_MODE		BIT(6)
+#define ILI9341_RGB_DISP_PATH_MEM	BIT(7)
+
+#define ILI9341_DBI_VCOMH_4P6V		0x23
+#define ILI9341_DBI_PWR_2_DEFAULT	0x10
+#define ILI9341_DBI_PRC_NORMAL		0x20
+#define ILI9341_DBI_VCOM_1_VMH_4P25V	0x3e
+#define ILI9341_DBI_VCOM_1_VML_1P5V	0x28
+#define ILI9341_DBI_VCOM_2_DEC_58	0x86
+#define ILI9341_DBI_FRC_DIVA		0x00
+#define ILI9341_DBI_FRC_RTNA		0x1b
+#define ILI9341_DBI_EMS_GAS		BIT(0)
+#define ILI9341_DBI_EMS_DTS		BIT(1)
+#define ILI9341_DBI_EMS_GON		BIT(2)
+
+/* struct ili9341_config - the system specific ILI9341 configuration */
+struct ili9341_config {
+	u32 max_spi_speed;
+	/* mode: the drm display mode */
+	const struct drm_display_mode mode;
+	/* ca: TODO: need comments for this register */
+	u8 ca[ILI9341_CA_LEN];
+	/* power_b: TODO: need comments for this register */
+	u8 power_b[ILI9341_POWER_B_LEN];
+	/* power_seq: TODO: need comments for this register */
+	u8 power_seq[ILI9341_POWER_SEQ_LEN];
+	/* dtca: TODO: need comments for this register */
+	u8 dtca[ILI9341_DTCA_LEN];
+	/* dtcb: TODO: need comments for this register */
+	u8 dtcb[ILI9341_DTCB_LEN];
+	/* power_a: TODO: need comments for this register */
+	u8 power_a[ILI9341_POWER_A_LEN];
+	/* frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */
+	u8 frc[ILI9341_FRC_LEN];
+	/* prc: TODO: need comments for this register */
+	u8 prc;
+	/* dfc_1: B6h DISCTRL (Display Function Control) */
+	u8 dfc_1[ILI9341_DFC_1_LEN];
+	/* power_1: Power Control 1 (C0h) */
+	u8 power_1;
+	/* power_2: Power Control 2 (C1h) */
+	u8 power_2;
+	/* vcom_1: VCOM Control 1(C5h) */
+	u8 vcom_1[ILI9341_VCOM_1_LEN];
+	/* vcom_2: VCOM Control 2(C7h) */
+	u8 vcom_2;
+	/* address_mode: Memory Access Control (36h) */
+	u8 address_mode;
+	/* g3amma_en: TODO: need comments for this register */
+	u8 g3amma_en;
+	/* rgb_interface: RGB Interface Signal Control (B0h) */
+	u8 rgb_interface;
+	/* dfc_2: refer to dfc_1 */
+	u8 dfc_2[ILI9341_DFC_2_LEN];
+	/* column_addr: Column Address Set (2Ah) */
+	u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
+	/* page_addr: Page Address Set (2Bh) */
+	u8 page_addr[ILI9341_PAGE_ADDR_LEN];
+	/* interface: Interface Control (F6h) */
+	u8 interface[ILI9341_INTERFACE_LEN];
+	/*
+	 * pixel_format: This command sets the pixel format for the RGB
+	 * image data used by
+	 */
+	u8 pixel_format;
+	/*
+	 * gamma_curve: This command is used to select the desired Gamma
+	 * curve for the
+	 */
+	u8 gamma_curve;
+	/* pgamma: Positive Gamma Correction (E0h) */
+	u8 pgamma[ILI9341_PGAMMA_LEN];
+	/* ngamma: Negative Gamma Correction (E1h) */
+	u8 ngamma[ILI9341_NGAMMA_LEN];
+};
+
+struct ili9341 {
+	struct device *dev;
+	const struct ili9341_config *conf;
+	struct drm_panel panel;
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *dc_gpio;
+	struct mipi_dbi *dbi;
+	u32 max_spi_speed;
+	struct regulator_bulk_data supplies[3];
+};
+
+/*
+ * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
+ */
+static const struct ili9341_config ili9341_stm32f429_disco_data = {
+	.max_spi_speed = 10000000,
+	.mode = {
+		.clock = 6100,
+		.hdisplay = 240,
+		.hsync_start = 240 + 10,/* hfp 10 */
+		.hsync_end = 240 + 10 + 10,/* hsync 10 */
+		.htotal = 240 + 10 + 10 + 20,/* hbp 20 */
+		.vdisplay = 320,
+		.vsync_start = 320 + 4,/* vfp 4 */
+		.vsync_end = 320 + 4 + 2,/* vsync 2 */
+		.vtotal = 320 + 4 + 2 + 2,/* vbp 2 */
+		.flags = 0,
+		.width_mm = 65,
+		.height_mm = 50,
+		.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	},
+	.ca = {0xc3, 0x08, 0x50},
+	.power_b = {0x00, 0xc1, 0x30},
+	.power_seq = {0x64, 0x03, 0x12, 0x81},
+	.dtca = {0x85, 0x00, 0x78},
+	.power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
+	.prc = 0x20,
+	.dtcb = {0x00, 0x00},
+	/* 0x00 fosc, 0x1b 70hz */
+	.frc = {0x00, 0x1b},
+	/*
+	 * 0x0a Interval scan, AGND AGND AGND AGND
+	 * 0xa2 Normally white, G1 -> G320, S720 -> S1,
+	 *	Scan Cycle 5 frames,85ms
+	 */
+	.dfc_1 = {0x0a, 0xa2},
+	/* 0x10 3.65v */
+	.power_1 = 0x10,
+	/* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
+	.power_2 = 0x10,
+	/* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
+	.vcom_1 = {0x45, 0x15},
+	/* 0x90 offset voltage, VMH-48, VML-48 */
+	.vcom_2 = 0x90,
+	/*
+	 * 0xc8 Row Address Order, Column Address Order
+	 * BGR 1
+	 */
+	.address_mode = 0xc8,
+	.g3amma_en = 0x00,
+	/*
+	 * 0xc2
+	 * Display Data Path: Memory
+	 * RGB: DE mode
+	 * DOTCLK polarity set (data fetched at the falling time)
+	 */
+	.rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
+			ILI9341_RGB_DE_MODE |
+			ILI9341_RGB_DPL,
+	/*
+	 * 0x0a
+	 * Gate outputs in non-display area: Interval scan
+	 * Determine source/VCOM output in a non-display area in the partial
+	 * display mode: AGND AGND AGND AGND
+	 *
+	 * 0xa7
+	 * Scan Cycle: 15 frames
+	 * fFLM = 60Hz: 255ms
+	 * Liquid crystal type: Normally white
+	 * Gate Output Scan Direction: G1 -> G320
+	 * Source Output Scan Direction: S720 -> S1
+	 *
+	 * 0x27
+	 * LCD Driver Line: 320 lines
+	 *
+	 * 0x04
+	 * PCDIV: 4
+	 */
+	.dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
+	/* column address: 240 */
+	.column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
+				ILI9341_COLUMN_ADDR & 0xff},
+	/* page address: 320 */
+	.page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
+				ILI9341_PAGE_ADDR & 0xff},
+	/*
+	 * Memory write control: When the transfer number of data exceeds
+	 * (EC-SC+1)*(EP-SP+1), the column and page number will be
+	 * reset, and the exceeding data will be written into the following
+	 * column and page.
+	 * Display Operation Mode: RGB Interface Mode
+	 * Interface for RAM Access: RGB interface
+	 * 16- bit RGB interface (1 transfer/pixel)
+	 */
+	.interface = {ILI9341_IF_WE_MODE, 0x00,
+			ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},
+	/* DPI: 16 bits / pixel */
+	.pixel_format = ILI9341_PIXEL_DPI_16_BITS,
+	/* Curve Selected: Gamma curve 1 (G2.2) */
+	.gamma_curve = ILI9341_GAMMA_CURVE_1,
+	.pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
+			0x09, 0x4e, 0x78, 0x3c, 0x09,
+			0x13, 0x05, 0x17, 0x11, 0x00},
+	.ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
+			0x07, 0x31, 0x33, 0x42, 0x05,
+			0x0c, 0x0a, 0x28, 0x2f, 0x0f},
+};
+
+static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
+{
+	return container_of(panel, struct ili9341, panel);
+}
+
+static void ili9341_dpi_init(struct ili9341 *ili)
+{
+	struct device *dev = (&ili->panel)->dev;
+	struct mipi_dbi *dbi = ili->dbi;
+	struct ili9341_config *cfg = (struct ili9341_config *)ili->conf;
+
+	/* Power Control */
+	mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b,
+				  ILI9341_POWER_B_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq,
+				  ILI9341_POWER_SEQ_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca,
+				  ILI9341_DTCA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a,
+				  ILI9341_POWER_A_LEN);
+	mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb,
+				  ILI9341_DTCB_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1,
+				  ILI9341_DFC_1_LEN);
+	mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1);
+	mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2);
+
+	/* VCOM */
+	mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1,
+				  ILI9341_VCOM_1_LEN);
+	mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode);
+
+	/* Gamma */
+	mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en);
+	mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2,
+				  ILI9341_DFC_2_LEN);
+
+	/* Colomn address set */
+	mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS,
+				  cfg->column_addr, ILI9341_COLUMN_ADDR_LEN);
+
+	/* Page address set */
+	mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS,
+				  cfg->page_addr, ILI9341_PAGE_ADDR_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface,
+				  ILI9341_INTERFACE_LEN);
+
+	/* Format */
+	mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format);
+	mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
+	msleep(200);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma,
+				  ILI9341_PGAMMA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma,
+				  ILI9341_NGAMMA_LEN);
+	mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(200);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+	mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
+
+	dev_info(dev, "Initialized display rgb interface\n");
+}
+
+static int ili9341_dpi_power_on(struct ili9341 *ili)
+{
+	struct device *dev = (&ili->panel)->dev;
+	int ret = 0;
+
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Enable power */
+	ret = regulator_bulk_enable(ARRAY_SIZE(ili->supplies),
+				    ili->supplies);
+	if (ret < 0) {
+		dev_err(dev, "unable to enable vcc\n");
+		return ret;
+	}
+	msleep(20);
+
+	/* De-assert RESET */
+	gpiod_set_value(ili->reset_gpio, 0);
+	msleep(20);
+
+	return 0;
+}
+
+static int ili9341_dpi_power_off(struct ili9341 *ili)
+{
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Disable power */
+	return regulator_bulk_disable(ARRAY_SIZE(ili->supplies),
+				      ili->supplies);
+}
+
+static int ili9341_dpi_disable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF);
+	return 0;
+}
+
+static int ili9341_dpi_unprepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	return ili9341_dpi_power_off(ili);
+}
+
+static int ili9341_dpi_prepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	int ret;
+
+	ret = ili9341_dpi_power_on(ili);
+	if (ret < 0)
+		return ret;
+
+	ili9341_dpi_init(ili);
+
+	return ret;
+}
+
+static int ili9341_dpi_enable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON);
+	return 0;
+}
+
+static int ili9341_dpi_get_modes(struct drm_panel *panel,
+				 struct drm_connector *connector)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	struct drm_device *drm = connector->dev;
+	struct drm_display_mode *mode;
+	struct drm_display_info *info;
+
+	info = &connector->display_info;
+	info->width_mm = ili->conf->mode.width_mm;
+	info->height_mm = ili->conf->mode.height_mm;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
+		info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
+
+	mode = drm_mode_duplicate(drm, &ili->conf->mode);
+	if (!mode) {
+		drm_err(drm, "bad mode or failed to add mode\n");
+		return -EINVAL;
+	}
+	drm_mode_set_name(mode);
+
+	/* Set up the polarity */
+	if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
+		mode->flags |= DRM_MODE_FLAG_PHSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NHSYNC;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
+		mode->flags |= DRM_MODE_FLAG_PVSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NVSYNC;
+
+	drm_mode_probed_add(connector, mode);
+
+	return 1; /* Number of modes */
+}
+
+static const struct drm_panel_funcs ili9341_dpi_funcs = {
+	.disable = ili9341_dpi_disable,
+	.unprepare = ili9341_dpi_unprepare,
+	.prepare = ili9341_dpi_prepare,
+	.enable = ili9341_dpi_enable,
+	.get_modes = ili9341_dpi_get_modes,
+};
+
+static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
+			       struct drm_crtc_state *crtc_state,
+			       struct drm_plane_state *plane_state)
+{
+	struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
+	struct mipi_dbi *dbi = &dbidev->dbi;
+	u8 addr_mode;
+	int ret, idx;
+
+	if (!drm_dev_enter(pipe->crtc.dev, &idx))
+		return;
+
+	ret = mipi_dbi_poweron_conditional_reset(dbidev);
+	if (ret < 0)
+		goto out_exit;
+	if (ret == 1)
+		goto out_enable;
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
+
+	mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
+	mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
+	mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
+	mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
+	mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
+	mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
+
+	/* Power Control */
+	mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
+	mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
+	/* VCOM */
+	mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
+			 ILI9341_DBI_VCOM_1_VML_1P5V);
+	mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
+
+	/* Memory Access Control */
+	mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
+			 MIPI_DCS_PIXEL_FMT_16BIT);
+
+	/* Frame Rate */
+	mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
+			 ILI9341_DBI_FRC_RTNA & 0x1f);
+
+	/* Gamma */
+	mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
+	mipi_dbi_command(dbi, ILI9341_PGAMMA,
+			 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,
+			 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);
+	mipi_dbi_command(dbi, ILI9341_NGAMMA,
+			 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,
+			 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);
+
+	/* DDRAM */
+	mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
+			 ILI9341_DBI_EMS_DTS |
+			 ILI9341_DBI_EMS_GON);
+
+	/* Display */
+	mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(100);
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+	msleep(100);
+
+out_enable:
+	switch (dbidev->rotation) {
+	default:
+		addr_mode = ILI9341_MADCTL_MX;
+		break;
+	case 90:
+		addr_mode = ILI9341_MADCTL_MV;
+		break;
+	case 180:
+		addr_mode = ILI9341_MADCTL_MY;
+		break;
+	case 270:
+		addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |
+			    ILI9341_MADCTL_MX;
+		break;
+	}
+
+	addr_mode |= ILI9341_MADCTL_BGR;
+	mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
+	mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
+	drm_info(&dbidev->drm, "Initialized display serial interface\n");
+out_exit:
+	drm_dev_exit(idx);
+}
+
+static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
+	.enable = ili9341_dbi_enable,
+	.disable = mipi_dbi_pipe_disable,
+	.update = mipi_dbi_pipe_update,
+	.prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
+};
+
+static const struct drm_display_mode ili9341_dbi_mode = {
+	DRM_SIMPLE_MODE(240, 320, 37, 49),
+};
+
+DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
+
+static struct drm_driver ili9341_dbi_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
+	.fops			= &ili9341_dbi_fops,
+	DRM_GEM_CMA_DRIVER_OPS_VMAP,
+	.debugfs_init		= mipi_dbi_debugfs_init,
+	.name			= "ili9341",
+	.desc			= "Ilitek ILI9341",
+	.date			= "20210716",
+	.major			= 1,
+	.minor			= 0,
+};
+
+static int ili9341_dbi_probe(struct spi_device *spi, struct gpio_desc *dc,
+			     struct gpio_desc *reset)
+{
+	struct device *dev = &spi->dev;
+	struct mipi_dbi_dev *dbidev;
+	struct mipi_dbi *dbi;
+	struct drm_device *drm;
+	struct regulator *vcc;
+	u32 rotation = 0;
+	int ret;
+
+	vcc = devm_regulator_get_optional(dev, "vcc");
+	if (IS_ERR(vcc))
+		dev_err(dev, "get optional vcc failed\n");
+
+	dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
+				    struct mipi_dbi_dev, drm);
+	if (IS_ERR(dbidev))
+		return PTR_ERR(dbidev);
+
+	dbi = &dbidev->dbi;
+	drm = &dbidev->drm;
+	dbi->reset = reset;
+	dbidev->regulator = vcc;
+
+	drm_mode_config_init(drm);
+
+	dbidev->backlight = devm_of_find_backlight(dev);
+	if (IS_ERR(dbidev->backlight))
+		return PTR_ERR(dbidev->backlight);
+
+	device_property_read_u32(dev, "rotation", &rotation);
+
+	ret = mipi_dbi_spi_init(spi, dbi, dc);
+	if (ret)
+		return ret;
+
+	ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
+				&ili9341_dbi_mode, rotation);
+	if (ret)
+		return ret;
+
+	drm_mode_config_reset(drm);
+
+	ret = drm_dev_register(drm, 0);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, drm);
+
+	drm_fbdev_generic_setup(drm, 0);
+
+	return 0;
+}
+
+static int ili9341_dpi_probe(struct spi_device *spi, struct gpio_desc *dc,
+			     struct gpio_desc *reset)
+{
+	struct device *dev = &spi->dev;
+	struct ili9341 *ili;
+	int ret;
+
+	ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
+	if (!ili)
+		return -ENOMEM;
+
+	ili->dbi = devm_kzalloc(dev, sizeof(struct mipi_dbi),
+				GFP_KERNEL);
+	if (!ili->dbi)
+		return -ENOMEM;
+
+	ili->supplies[0].supply = "vci";
+	ili->supplies[1].supply = "vddi";
+	ili->supplies[2].supply = "vddi-led";
+	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(ili->supplies),
+				      ili->supplies);
+	if (ret < 0) {
+		dev_err(dev, "failed to get regulators: %d\n", ret);
+		return ret;
+	}
+
+	ret = mipi_dbi_spi_init(spi, ili->dbi, dc);
+	if (ret)
+		return ret;
+
+	spi_set_drvdata(spi, ili);
+	ili->reset_gpio = reset;
+	/*
+	 * Every new incarnation of this display must have a unique
+	 * data entry for the system in this driver.
+	 */
+	ili->conf = of_device_get_match_data(dev);
+	if (!ili->conf) {
+		dev_err(dev, "missing device configuration\n");
+		return -ENODEV;
+	}
+
+	ili->max_spi_speed = ili->conf->max_spi_speed;
+	drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
+		       DRM_MODE_CONNECTOR_DPI);
+	drm_panel_add(&ili->panel);
+
+	return 0;
+}
+
+static int ili9341_probe(struct spi_device *spi)
+{
+	struct device *dev = &spi->dev;
+	struct gpio_desc *dc;
+	struct gpio_desc *reset;
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(reset))
+		dev_err(dev, "Failed to get gpio 'reset'\n");
+
+	dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(dc))
+		dev_err(dev, "Failed to get gpio 'dc'\n");
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t"))
+		return ili9341_dpi_probe(spi, dc, reset);
+	else if (!strcmp(id->name, "yx240qv29"))
+		return ili9341_dbi_probe(spi, dc, reset);
+
+	return -1;
+}
+
+static int ili9341_remove(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+	struct ili9341 *ili = spi_get_drvdata(spi);
+	struct drm_device *drm = spi_get_drvdata(spi);
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t")) {
+		ili9341_dpi_power_off(ili);
+		drm_panel_remove(&ili->panel);
+	} else if (!strcmp(id->name, "yx240qv29")) {
+		drm_dev_unplug(drm);
+		drm_atomic_helper_shutdown(drm);
+	}
+	return 0;
+}
+
+static void ili9341_shutdown(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	if (!strcmp(id->name, "yx240qv29"))
+		drm_atomic_helper_shutdown(spi_get_drvdata(spi));
+}
+
+static const struct of_device_id ili9341_of_match[] = {
+	{
+		.compatible = "st,sf-tc240t-9370-t",
+		.data = &ili9341_stm32f429_disco_data,
+	},
+	{
+		/* porting from tiny/ili9341.c
+		 * for original mipi dbi compitable
+		 */
+		.compatible = "adafruit,yx240qv29",
+		.data = NULL,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ili9341_of_match);
+
+static const struct spi_device_id ili9341_id[] = {
+	{ "yx240qv29", 0 },
+	{ "sf-tc240t-9370-t", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ili9341_id);
+
+static struct spi_driver ili9341_driver = {
+	.probe = ili9341_probe,
+	.remove = ili9341_remove,
+	.shutdown = ili9341_shutdown,
+	.id_table = ili9341_id,
+	.driver = {
+		.name = "panel-ilitek-ili9341",
+		.of_match_table = ili9341_of_match,
+	},
+};
+module_spi_driver(ili9341_driver);
+
+MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>");
+MODULE_DESCRIPTION("ILI9341 LCD panel driver");
+MODULE_LICENSE("GPL v2");
-- 
1.9.1

Re: [PATCH v4 0/3] Add ilitek ili9341 panel driver

[Dillon Min]

Hi All

Just a gentle ping, thanks.

Best regards.
Dillon

On Sat, 24 Jul 2021 at 11:44, <dillon.minfei@gmail.com> wrote:
>
> From: Dillon Min <dillon.minfei@gmail.com>
>
> Since the st,sf-tc240t-9370-t dts binding already exist in stm32f429-disco.dts
> but, the panel driver didn't get accepted from mainline. it's time to submit
> patch fot it.
>
> This driver can support two different interface by different dts bindings:
> - spi+dpi, use spi to configure register, dpi for graphic data.
>   st,sf-tc240t-9370-t
> - only spi, just like tiny/ili9341.c (actually, this part is copy from tiny)
>   adafruit,yx240qv29
>
> I was submited the first patch last year, you can find it at [1].
> this patch has one major difference from that one, which is replace the low
> level communication way, from spi_sync() to mipi_dbi_{command,
> command_stackbuf}() interface, referred from Linus's patch [2].
>
> both the two dpi/dbi interface was tested on stm32f429-disco board, if anyone
> want to verify this patch, you need apply the clk patch for this board first,
> you can get it from [3].
>
> [1] "drm/panel: Add ilitek ili9341 panel driver"
> https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@gmail.com/
>
> [2] "drm/panel: s6e63m0: Switch to DBI abstraction for SPI"
> https://lore.kernel.org/dri-devel/20210611214243.669892-1-linus.walleij@linaro.org/
>
> [3]
> https://lore.kernel.org/lkml/1590378348-8115-6-git-send-email-dillon.minfei@gmail.com/
>
> v4:
> - fix m68k-allmodconfig build error which reported by lkp, thanks.
> - add Copyright 2018 David Lechner <david@lechnology.com>.
> v3 link:
> https://lore.kernel.org/lkml/1627013203-23099-1-git-send-email-dillon.minfei@gmail.com/
>
> v3:
> - add Fixes tags.
> - collect reviewed-by tags from linus and jagan.
> - replace DRM_ERROR() with dev_err() or drm_err().
> - remove kernel-doc markers from struct ili9341_config{}.
> - reorder include headers.
> - remove the struct device *dev from struct ili9341{}.
> - restructure the ili9341_probe() function, add two ili9341_{dbi,dpi)_probe()
>   to make it more readable according to jagan's suggestion, thanks.
>
> for the full drm driver exist in drm/panel need Sam and Laurent's feedback.
> so, not cover this part at this time, will be update later.
>
> v2 link:
> https://lore.kernel.org/lkml/1626853288-31223-1-git-send-email-dillon.minfei@gmail.com/
>
> v2:
> - replace vcc regulator to bulk regulators in driver, from linus suggestion.
> - fix dtbs_check warnings on ili9341 dts binding check.
> - add bulk regulation node in ilitek,ili9341.yaml.
> v1 link:
> https://lore.kernel.org/lkml/1626430843-23823-1-git-send-email-dillon.minfei@gmail.com/
>
> Dillon Min (3):
>   dt-bindings: display: panel: Add ilitek ili9341 panel bindings
>   ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding
>   drm/panel: Add ilitek ili9341 panel driver
>
>  .../bindings/display/panel/ilitek,ili9341.yaml     |  78 ++
>  arch/arm/boot/dts/stm32f429-disco.dts              |   2 +-
>  drivers/gpu/drm/panel/Kconfig                      |  12 +
>  drivers/gpu/drm/panel/Makefile                     |   1 +
>  drivers/gpu/drm/panel/panel-ilitek-ili9341.c       | 792 +++++++++++++++++++++
>  5 files changed, 884 insertions(+), 1 deletion(-)
>  create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
>  create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
>
> --
> 1.9.1
>

Re: [PATCH v4 1/3] dt-bindings: display: panel: Add ilitek ili9341 panel bindings

[Linus Walleij]

On Sat, Jul 24, 2021 at 5:44 AM <dillon.minfei@gmail.com> wrote:

> From: Dillon Min <dillon.minfei@gmail.com>
>
> Add documentation for "ilitek,ili9341" panel.
>
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>
> Link: https://lore.kernel.org/lkml/1626853288-31223-2-git-send-email-dillon.minfei@gmail.com/

Patch applied to drm-misc-next.

Thanks for working on this!

Yours,
Linus Walleij

Re: [PATCH v4 3/3] drm/panel: Add ilitek ili9341 panel driver

[Linus Walleij]

On Sat, Jul 24, 2021 at 5:44 AM <dillon.minfei@gmail.com> wrote:

> From: Dillon Min <dillon.minfei@gmail.com>
>
> This driver combines tiny/ili9341.c mipi_dbi_interface driver
> with mipi_dpi_interface driver, can support ili9341 with serial
> mode and parallel rgb interface mode by different dts bindings.
>
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
> Reported-by: kernel test robot <lkp@intel.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
> ---
> v4:
> - fix m68k-allmodconfig build error which reported by lkp, thanks.
> - add Copyright 2018 David Lechner <david@lechnology.com>.

Patch applied to drm-misc-next

Thanks for working on this driver!

Yours,
Linus Walleij

Re: [PATCH v4 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding

[Linus Walleij]

On Sat, Jul 24, 2021 at 5:44 AM <dillon.minfei@gmail.com> wrote:

> From: Dillon Min <dillon.minfei@gmail.com>
>
> Since the compatible string defined from ilitek,ili9341.yaml is
> "st,sf-tc240t-9370-t", "ilitek,ili9341"
>
> so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
>
> arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
> ['st,sf-tc240t-9370-t'] is too short
>
> Fixes: a726e2f000ec ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
> Reported-by: kernel test robot <lkp@intel.com>
> ---
> v4: no change.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Please funnel this patch through the STM and ARM SoC tree.

Yours,
Linus Walleij

Re: [PATCH v4 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding

[Dillon Min]

Hi Linus

Thanks.

On Thu, 5 Aug 2021 at 17:11, Linus Walleij <linus.walleij@linaro.org> wrote:
>
> On Sat, Jul 24, 2021 at 5:44 AM <dillon.minfei@gmail.com> wrote:
>
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > Since the compatible string defined from ilitek,ili9341.yaml is
> > "st,sf-tc240t-9370-t", "ilitek,ili9341"
> >
> > so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
> >
> > arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
> > ['st,sf-tc240t-9370-t'] is too short
> >
> > Fixes: a726e2f000ec ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
> > Reported-by: kernel test robot <lkp@intel.com>
> > ---
> > v4: no change.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
>
> Please funnel this patch through the STM and ARM SoC tree.

Sure, I will let Alex know. Thanks for your help on this driver.

Hi Alex,
Should I send v5 with Linus's Reviewed-by tag on this patch? thanks.

Best Regards
Dillon

>
> Yours,
> Linus Walleij

Re: [PATCH v4 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding

[Alexandre TORGUE]

Hi Dillon

On 8/5/21 11:19 AM, Dillon Min wrote:
> Hi Linus
> 
> Thanks.
> 
> On Thu, 5 Aug 2021 at 17:11, Linus Walleij <linus.walleij@linaro.org> wrote:
>>
>> On Sat, Jul 24, 2021 at 5:44 AM <dillon.minfei@gmail.com> wrote:
>>
>>> From: Dillon Min <dillon.minfei@gmail.com>
>>>
>>> Since the compatible string defined from ilitek,ili9341.yaml is
>>> "st,sf-tc240t-9370-t", "ilitek,ili9341"
>>>
>>> so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
>>>
>>> arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
>>> ['st,sf-tc240t-9370-t'] is too short
>>>
>>> Fixes: a726e2f000ec ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
>>> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
>>> Reported-by: kernel test robot <lkp@intel.com>
>>> ---
>>> v4: no change.
>>
>> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
>>
>> Please funnel this patch through the STM and ARM SoC tree.
> 
> Sure, I will let Alex know. Thanks for your help on this driver.
> 
> Hi Alex,
> Should I send v5 with Linus's Reviewed-by tag on this patch? thanks.

No, I'll do it.

cheers
alex

> 
> Best Regards
> Dillon
> 
>>
>> Yours,
>> Linus Walleij

Re: [PATCH v4 0/3] Add ilitek ili9341 panel driver

[Andy Shevchenko]

On Sat, Jul 24, 2021 at 6:46 AM <dillon.minfei@gmail.com> wrote:
>
> From: Dillon Min <dillon.minfei@gmail.com>
>
> Since the st,sf-tc240t-9370-t dts binding already exist in stm32f429-disco.dts
> but, the panel driver didn't get accepted from mainline. it's time to submit
> patch fot it.
>
> This driver can support two different interface by different dts bindings:
> - spi+dpi, use spi to configure register, dpi for graphic data.
>   st,sf-tc240t-9370-t
> - only spi, just like tiny/ili9341.c (actually, this part is copy from tiny)
>   adafruit,yx240qv29

...

> I was submited the first patch last year, you can find it at [1].

submitted

> this patch has one major difference from that one, which is replace the low
> level communication way, from spi_sync() to mipi_dbi_{command,
> command_stackbuf}() interface, referred from Linus's patch [2].

Can you shed a light on the road map here.
I have the SPI panel (tiny) based on the ILI9341 and I'm using
actually mi0283qt driver. With yours we will have 3 (three!) drivers
for the same chip. I really do not want this. Without road map on the
prospective of these all drivers, NAK.

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v4 0/3] Add ilitek ili9341 panel driver

[Dillon Min]

Hi Andy

Thanks for your question.

On Thu, 5 Aug 2021 at 18:16, Andy Shevchenko <andy.shevchenko@gmail.com> wrote:
>
> On Sat, Jul 24, 2021 at 6:46 AM <dillon.minfei@gmail.com> wrote:
> >
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > Since the st,sf-tc240t-9370-t dts binding already exist in stm32f429-disco.dts
> > but, the panel driver didn't get accepted from mainline. it's time to submit
> > patch fot it.
> >
> > This driver can support two different interface by different dts bindings:
> > - spi+dpi, use spi to configure register, dpi for graphic data.
> >   st,sf-tc240t-9370-t
> > - only spi, just like tiny/ili9341.c (actually, this part is copy from tiny)
> >   adafruit,yx240qv29
>
> ...
>
> > I was submited the first patch last year, you can find it at [1].
>
> submitted

Thanks.

>
> > this patch has one major difference from that one, which is replace the low
> > level communication way, from spi_sync() to mipi_dbi_{command,
> > command_stackbuf}() interface, referred from Linus's patch [2].
>
> Can you shed a light on the road map here.

Personally, I'd like to merge tiny/mi0283qt.c, tiny/ili9341.c(already
done) into this driver later
(keep original author, copyright, dts compatible string).
then remove these two drivers under tiny, but it's up to Sam and
Laurent agreement.

For long term, just like Peter suggested, let all panel based on
ili9xxx with single-dbi or dbi & dpi interface to be supported by
single ilitek-ili9xxx.c, something like panel/panel-simple.c
 (panel/panel-ilitek-ili9322c, tiny/ili9225.c, tiny/ili9486.c,
tiny/mi0283qt.c, etc).
it's also needs maintainers permission.

> I have the SPI panel (tiny) based on the ILI9341 and I'm using
> actually mi0283qt driver. With yours we will have 3 (three!) drivers
> for the same chip. I really do not want this. Without road map on the
> prospective of these all drivers, NAK.

Yes, it will make users confused if there are three different drivers
for the same chip.
I'll continue to work on this driver.

Thanks again for point this out.

Best Regards
Dillon

>
> --
> With Best Regards,
> Andy Shevchenko

Re: [PATCH v4 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341 dts binding

[Alexandre TORGUE]

Hi Dillon

On 7/24/21 5:44 AM, dillon.minfei@gmail.com wrote:
> From: Dillon Min <dillon.minfei@gmail.com>
> 
> Since the compatible string defined from ilitek,ili9341.yaml is
> "st,sf-tc240t-9370-t", "ilitek,ili9341"
> 
> so, append "ilitek,ili9341" to avoid the below dtbs_check warning.
> 
> arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
> ['st,sf-tc240t-9370-t'] is too short
> 
> Fixes: a726e2f000ec ("ARM: dts: stm32: enable ltdc binding with ili9341, gyro l3gd20 on stm32429-disco board")
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
> Reported-by: kernel test robot <lkp@intel.com>
> ---
> v4: no change.
> 
>   arch/arm/boot/dts/stm32f429-disco.dts | 2 +-
>   1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
> index 075ac57d0bf4..6435e099c632 100644
> --- a/arch/arm/boot/dts/stm32f429-disco.dts
> +++ b/arch/arm/boot/dts/stm32f429-disco.dts
> @@ -192,7 +192,7 @@
>   
>   	display: display@1{
>   		/* Connect panel-ilitek-9341 to ltdc */
> -		compatible = "st,sf-tc240t-9370-t";
> +		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
>   		reg = <1>;
>   		spi-3wire;
>   		spi-max-frequency = <10000000>;
> 

Patch applied on stm32-next. I updated commit title to indicate targeted 
board.

regards
Alex