From: Hsin-Yi Wang <hsinyi@chromium.org>
To: Xin Ji <xji@analogixsemi.com>,
dri-devel <dri-devel@lists.freedesktop.org>
Cc: David Airlie <airlied@linux.ie>,
Robert Foss <robert.foss@linaro.org>,
Sam Ravnborg <sam@ravnborg.org>, Rob Herring <robh+dt@kernel.org>,
Daniel Vetter <daniel@ffwll.ch>,
Devicetree List <devicetree@vger.kernel.org>,
lkml <linux-kernel@vger.kernel.org>,
Laurent Pinchart <Laurent.pinchart@ideasonboard.com>,
Neil Armstrong <narmstrong@baylibre.com>
Subject: Re: [PATCH v4 2/2] drm/bridge: anx7625: disable regulators when power off
Date: Thu, 18 Mar 2021 12:26:25 +0800 [thread overview]
Message-ID: <CAJMQK-ho9Ncqd=muCv-aMsHSRhgKtC3H6asxR=+3CODpeiWQWQ@mail.gmail.com> (raw)
In-Reply-To: <20210224061409.3996755-2-hsinyi@chromium.org>
On Wed, Feb 24, 2021 at 2:14 PM Hsin-Yi Wang <hsinyi@chromium.org> wrote:
>
> When suspending the driver, anx7625_power_standby() will be called to
> turn off reset-gpios and enable-gpios. However, power supplies are not
> disabled. To save power, the driver can get the power supply regulators
> and turn off them in anx7625_power_standby().
>
> Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
> Reviewed-by: Robert Foss <robert.foss@linaro.org>
> ---
Ping on the thread, thanks.
> drivers/gpu/drm/bridge/analogix/anx7625.c | 34 +++++++++++++++++++++++
> drivers/gpu/drm/bridge/analogix/anx7625.h | 1 +
> 2 files changed, 35 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> index 65cc05982f826..23283ba0c4f93 100644
> --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> @@ -11,6 +11,7 @@
> #include <linux/kernel.h>
> #include <linux/module.h>
> #include <linux/mutex.h>
> +#include <linux/regulator/consumer.h>
> #include <linux/slab.h>
> #include <linux/types.h>
> #include <linux/workqueue.h>
> @@ -875,12 +876,25 @@ static int sp_tx_edid_read(struct anx7625_data *ctx,
> static void anx7625_power_on(struct anx7625_data *ctx)
> {
> struct device *dev = &ctx->client->dev;
> + int ret, i;
>
> if (!ctx->pdata.low_power_mode) {
> DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n");
> return;
> }
>
> + for (i = 0; i < ARRAY_SIZE(ctx->pdata.supplies); i++) {
> + ret = regulator_enable(ctx->pdata.supplies[i].consumer);
> + if (ret < 0) {
> + DRM_DEV_DEBUG_DRIVER(dev, "cannot enable supply %d: %d\n",
> + i, ret);
> + goto reg_err;
> + }
> + usleep_range(2000, 2100);
> + }
> +
> + usleep_range(4000, 4100);
> +
> /* Power on pin enable */
> gpiod_set_value(ctx->pdata.gpio_p_on, 1);
> usleep_range(10000, 11000);
> @@ -889,11 +903,16 @@ static void anx7625_power_on(struct anx7625_data *ctx)
> usleep_range(10000, 11000);
>
> DRM_DEV_DEBUG_DRIVER(dev, "power on !\n");
> + return;
> +reg_err:
> + for (--i; i >= 0; i--)
> + regulator_disable(ctx->pdata.supplies[i].consumer);
> }
>
> static void anx7625_power_standby(struct anx7625_data *ctx)
> {
> struct device *dev = &ctx->client->dev;
> + int ret;
>
> if (!ctx->pdata.low_power_mode) {
> DRM_DEV_DEBUG_DRIVER(dev, "not low power mode!\n");
> @@ -904,6 +923,12 @@ static void anx7625_power_standby(struct anx7625_data *ctx)
> usleep_range(1000, 1100);
> gpiod_set_value(ctx->pdata.gpio_p_on, 0);
> usleep_range(1000, 1100);
> +
> + ret = regulator_bulk_disable(ARRAY_SIZE(ctx->pdata.supplies),
> + ctx->pdata.supplies);
> + if (ret < 0)
> + DRM_DEV_DEBUG_DRIVER(dev, "cannot disable supplies %d\n", ret);
> +
> DRM_DEV_DEBUG_DRIVER(dev, "power down\n");
> }
>
> @@ -1742,6 +1767,15 @@ static int anx7625_i2c_probe(struct i2c_client *client,
> platform->client = client;
> i2c_set_clientdata(client, platform);
>
> + pdata->supplies[0].supply = "vdd10";
> + pdata->supplies[1].supply = "vdd18";
> + pdata->supplies[2].supply = "vdd33";
> + ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(pdata->supplies),
> + pdata->supplies);
> + if (ret) {
> + DRM_DEV_ERROR(dev, "fail to get power supplies: %d\n", ret);
> + return ret;
> + }
> anx7625_init_gpio(platform);
>
> atomic_set(&platform->power_status, 0);
> diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
> index 193ad86c54503..e4a086b3a3d7b 100644
> --- a/drivers/gpu/drm/bridge/analogix/anx7625.h
> +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
> @@ -350,6 +350,7 @@ struct s_edid_data {
> struct anx7625_platform_data {
> struct gpio_desc *gpio_p_on;
> struct gpio_desc *gpio_reset;
> + struct regulator_bulk_data supplies[3];
> struct drm_bridge *panel_bridge;
> int intp_irq;
> u32 low_power_mode;
> --
> 2.30.1.766.gb4fecdf3b7-goog
>
next prev parent reply other threads:[~2021-03-18 4:28 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-02-24 6:14 [PATCH v4 1/2] dt-bindings: drm/bridge: anx7625: Add power supplies Hsin-Yi Wang
2021-02-24 6:14 ` [PATCH v4 2/2] drm/bridge: anx7625: disable regulators when power off Hsin-Yi Wang
2021-03-18 4:26 ` Hsin-Yi Wang [this message]
2021-03-19 2:49 ` Xin Ji
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAJMQK-ho9Ncqd=muCv-aMsHSRhgKtC3H6asxR=+3CODpeiWQWQ@mail.gmail.com' \
--to=hsinyi@chromium.org \
--cc=Laurent.pinchart@ideasonboard.com \
--cc=airlied@linux.ie \
--cc=daniel@ffwll.ch \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
--cc=robert.foss@linaro.org \
--cc=robh+dt@kernel.org \
--cc=sam@ravnborg.org \
--cc=xji@analogixsemi.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).