linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH 0/2] Add ilitek ili9341 panel driver
@ 2021-07-16 10:20 dillon.minfei
  2021-07-16 10:20 ` [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings dillon.minfei
  2021-07-16 10:20 ` [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver dillon.minfei
  0 siblings, 2 replies; 9+ messages in thread
From: dillon.minfei @ 2021-07-16 10:20 UTC (permalink / raw)
  To: thierry.reding, sam, airlied, daniel, robh+dt, linus.walleij
  Cc: noralf, dianders, alexandre.torgue, dri-devel, devicetree,
	linux-kernel, Dillon Min

From: Dillon Min <dillon.minfei@gmail.com>

Since the st,sf-tc240t-9370-t dts binding already exist in stm32f429-disco.dts
but, the panel driver didn't get accepted from mainline. it's time to submit
patch fot it.

This driver can support two different interface by different dts bindings:
- spi+dpi, use spi to configure register, dpi for graphic data.
  st,sf-tc240t-9370-t
- only spi, just like tiny/ili9341.c (actually, this part is copy from tiny)
  adafruit,yx240qv29

I submited the first patch last year, you can find it at [1].
this patch has one major difference from that one, which is replace the low
level communication way, from spi_sync() to mipi_dbi_{command,
command_stackbuf}() interface, referred from Linus's patch [2].

both the two dpi/dbi interface was tested on stm32f429-disco board, if anyone
want to verify this patch, you need apply the clk patch for this board first,
you can get it from [3]

[1] "drm/panel: Add ilitek ili9341 panel driver"
https://lore.kernel.org/lkml/1590378348-8115-7-git-send-email-dillon.minfei@gmail.com/

[2] "drm/panel: s6e63m0: Switch to DBI abstraction for SPI"
https://lore.kernel.org/dri-devel/20210611214243.669892-1-linus.walleij@linaro.org/

[3]
https://lore.kernel.org/lkml/1590378348-8115-6-git-send-email-dillon.minfei@gmail.com/


Dillon Min (2):
  dt-bindings: display: panel: Add ilitek ili9341 panel bindings
  drm/panel: Add ilitek ili9341 panel driver

 .../bindings/display/panel/ilitek,ili9341.yaml     |  69 ++
 drivers/gpu/drm/panel/Kconfig                      |  12 +
 drivers/gpu/drm/panel/Makefile                     |   1 +
 drivers/gpu/drm/panel/panel-ilitek-ili9341.c       | 778 +++++++++++++++++++++
 4 files changed, 860 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c

-- 
2.7.4


^ permalink raw reply	[flat|nested] 9+ messages in thread

* [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings
  2021-07-16 10:20 [PATCH 0/2] Add ilitek ili9341 panel driver dillon.minfei
@ 2021-07-16 10:20 ` dillon.minfei
  2021-07-18  0:16   ` Linus Walleij
  2021-07-20  5:32   ` kernel test robot
  2021-07-16 10:20 ` [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver dillon.minfei
  1 sibling, 2 replies; 9+ messages in thread
From: dillon.minfei @ 2021-07-16 10:20 UTC (permalink / raw)
  To: thierry.reding, sam, airlied, daniel, robh+dt, linus.walleij
  Cc: noralf, dianders, alexandre.torgue, dri-devel, devicetree,
	linux-kernel, Dillon Min

From: Dillon Min <dillon.minfei@gmail.com>

Add documentation for "ilitek,ili9341" panel.

Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
---
 .../bindings/display/panel/ilitek,ili9341.yaml     | 69 ++++++++++++++++++++++
 1 file changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml

diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
new file mode 100644
index 000000000000..2172f889af3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/ilitek,ili9341.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ilitek-9341 Display Panel
+
+maintainers:
+  - Dillon Min <dillon.minfei@gmail.com>
+
+description: |
+  Ilitek ILI9341 TFT panel driver with SPI control bus
+  This is a driver for 320x240 TFT panels, accepting a rgb input
+  streams with 16 bits or 18 bits.
+
+allOf:
+  - $ref: panel-common.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          # ili9341 240*320 Color on stm32f429-disco board
+        - st,sf-tc240t-9370-t
+      - const: ilitek,ili9341
+
+  reg: true
+
+  dc-gpios:
+    maxItems: 1
+    description: Display data/command selection (D/CX)
+
+  spi-3wire: true
+
+  spi-max-frequency:
+    const: 10000000
+
+  port: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - dc-gpios
+  - port
+
+examples:
+  - |+
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        panel: display@0 {
+                 compatible = "st,sf-tc240t-9370-t",
+                              "ilitek,ili9341";
+                 reg = <0>;
+                 spi-3wire;
+                 spi-max-frequency = <10000000>;
+                 dc-gpios = <&gpiod 13 0>;
+                 port {
+                         panel_in: endpoint {
+                           remote-endpoint = <&display_out>;
+                      };
+                 };
+             };
+        };
+...
+
-- 
2.7.4


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver
  2021-07-16 10:20 [PATCH 0/2] Add ilitek ili9341 panel driver dillon.minfei
  2021-07-16 10:20 ` [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings dillon.minfei
@ 2021-07-16 10:20 ` dillon.minfei
  2021-07-18  0:31   ` Linus Walleij
  1 sibling, 1 reply; 9+ messages in thread
From: dillon.minfei @ 2021-07-16 10:20 UTC (permalink / raw)
  To: thierry.reding, sam, airlied, daniel, robh+dt, linus.walleij
  Cc: noralf, dianders, alexandre.torgue, dri-devel, devicetree,
	linux-kernel, Dillon Min

From: Dillon Min <dillon.minfei@gmail.com>

This driver combine tiny/ili9341.c mipi_dbi_interface driver
with mipi_dpi_interface driver, can support ili9341 with serial
mode or parallel rgb interface mode by register configuration.

Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
---
 drivers/gpu/drm/panel/Kconfig                |  12 +
 drivers/gpu/drm/panel/Makefile               |   1 +
 drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 778 +++++++++++++++++++++++++++
 3 files changed, 791 insertions(+)
 create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c

diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index ef87d92cdf49..eb34b8d1b19a 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -124,6 +124,18 @@ config DRM_PANEL_ILITEK_IL9322
 	  Say Y here if you want to enable support for Ilitek IL9322
 	  QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
 
+config DRM_PANEL_ILITEK_ILI9341
+	tristate "Ilitek ILI9341 240x320 QVGA panels"
+	depends on OF && SPI
+	depends on DRM_KMS_HELPER
+	depends on DRM_KMS_CMA_HELPER
+	depends on BACKLIGHT_CLASS_DEVICE
+	select DRM_MIPI_DBI
+	help
+	  Say Y here if you want to enable support for Ilitek IL9341
+	  QVGA (240x320) RGB panels. support serial & parallel rgb
+	  interface.
+
 config DRM_PANEL_ILITEK_ILI9881C
 	tristate "Ilitek ILI9881C-based panels"
 	depends on OF
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index cae4d976c069..0ecde184665d 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
 obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
 obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
+obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9341) += panel-ilitek-ili9341.o
 obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
 obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
 obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
new file mode 100644
index 000000000000..4fc312a43d3a
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
@@ -0,0 +1,778 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Ilitek ILI9341 TFT LCD drm_panel driver.
+ *
+ * This panel can be configured to support:
+ * - 16-bit parallel RGB interface
+ * - 18-bit parallel RGB interface
+ * - 4-line serial spi interface
+ *
+ * Copyright (C) 2021 Dillon Min <dillon.minfei@gmail.com>
+ * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
+ * the reuse of DBI abstraction part referred from Linus's patch
+ * "drm/panel: s6e63m0: Switch to DBI abstraction for SPI"
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/spi/spi.h>
+#include <linux/delay.h>
+#include <video/mipi_display.h>
+#include <drm/drm_mipi_dbi.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_atomic_helper.h>
+#include <drm/drm_atomic_helper.h>
+
+#include <drm/drm_drv.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_print.h>
+
+#define ILI9341_RGB_INTERFACE  0xb0   /* RGB Interface Signal Control */
+#define ILI9341_FRC            0xb1   /* Frame Rate Control register */
+#define ILI9341_DFC            0xb6   /* Display Function Control register */
+#define ILI9341_POWER1         0xc0   /* Power Control 1 register */
+#define ILI9341_POWER2         0xc1   /* Power Control 2 register */
+#define ILI9341_VCOM1          0xc5   /* VCOM Control 1 register */
+#define ILI9341_VCOM2          0xc7   /* VCOM Control 2 register */
+#define ILI9341_POWERA         0xcb   /* Power control A register */
+#define ILI9341_POWERB         0xcf   /* Power control B register */
+#define ILI9341_PGAMMA         0xe0   /* Positive Gamma Correction register */
+#define ILI9341_NGAMMA         0xe1   /* Negative Gamma Correction register */
+#define ILI9341_DTCA           0xe8   /* Driver timing control A */
+#define ILI9341_DTCB           0xea   /* Driver timing control B */
+#define ILI9341_POWER_SEQ      0xed   /* Power on sequence register */
+#define ILI9341_3GAMMA_EN      0xf2   /* 3 Gamma enable register */
+#define ILI9341_INTERFACE      0xf6   /* Interface control register */
+#define ILI9341_PRC            0xf7   /* Pump ratio control register */
+#define ILI9341_ETMOD	       0xb7   /* Entry mode set */
+
+#define ILI9341_MADCTL_BGR	BIT(3)
+#define ILI9341_MADCTL_MV	BIT(5)
+#define ILI9341_MADCTL_MX	BIT(6)
+#define ILI9341_MADCTL_MY	BIT(7)
+
+#define ILI9341_POWER_B_LEN	3
+#define ILI9341_POWER_SEQ_LEN	4
+#define ILI9341_DTCA_LEN	3
+#define ILI9341_DTCB_LEN	2
+#define ILI9341_POWER_A_LEN	5
+#define ILI9341_DFC_1_LEN	2
+#define ILI9341_FRC_LEN		2
+#define ILI9341_VCOM_1_LEN	2
+#define ILI9341_DFC_2_LEN	4
+#define ILI9341_COLUMN_ADDR_LEN	4
+#define ILI9341_PAGE_ADDR_LEN	4
+#define ILI9341_INTERFACE_LEN	3
+#define ILI9341_PGAMMA_LEN	15
+#define ILI9341_NGAMMA_LEN	15
+#define ILI9341_CA_LEN		3
+
+#define ILI9341_PIXEL_DPI_16_BITS	(BIT(6) | BIT(4))
+#define ILI9341_PIXEL_DPI_18_BITS	(BIT(6) | BIT(5))
+#define ILI9341_GAMMA_CURVE_1		BIT(0)
+#define ILI9341_IF_WE_MODE		BIT(0)
+#define ILI9341_IF_BIG_ENDIAN		0x00
+#define ILI9341_IF_DM_RGB		BIT(2)
+#define ILI9341_IF_DM_INTERNAL		0x00
+#define ILI9341_IF_DM_VSYNC		BIT(3)
+#define ILI9341_IF_RM_RGB		BIT(1)
+#define ILI9341_IF_RIM_RGB		0x00
+
+#define ILI9341_COLUMN_ADDR		0x00ef
+#define ILI9341_PAGE_ADDR		0x013f
+
+#define ILI9341_RGB_EPL			BIT(0)
+#define ILI9341_RGB_DPL			BIT(1)
+#define ILI9341_RGB_HSPL		BIT(2)
+#define ILI9341_RGB_VSPL		BIT(3)
+#define ILI9341_RGB_DE_MODE		BIT(6)
+#define ILI9341_RGB_DISP_PATH_MEM	BIT(7)
+
+#define ILI9341_DBI_VCOMH_4P6V		0x23
+#define ILI9341_DBI_PWR_2_DEFAULT	0x10
+#define ILI9341_DBI_PRC_NORMAL		0x20
+#define ILI9341_DBI_VCOM_1_VMH_4P25V	0x3e
+#define ILI9341_DBI_VCOM_1_VML_1P5V	0x28
+#define ILI9341_DBI_VCOM_2_DEC_58	0x86
+#define ILI9341_DBI_FRC_DIVA		0x00
+#define ILI9341_DBI_FRC_RTNA		0x1b
+#define ILI9341_DBI_EMS_GAS		BIT(0)
+#define ILI9341_DBI_EMS_DTS		BIT(1)
+#define ILI9341_DBI_EMS_GON		BIT(2)
+
+/**
+ * struct ili9341_config - the system specific ILI9341 configuration
+ * @max_spi_speed: 10000000
+ */
+struct ili9341_config {
+	u32 max_spi_speed;
+	/** @mode: the drm display mode */
+	const struct drm_display_mode mode;
+	/* @ca: TODO: need comments for this register */
+	u8 ca[ILI9341_CA_LEN];
+	/* @power_b: TODO: need comments for this register */
+	u8 power_b[ILI9341_POWER_B_LEN];
+	/* @power_seq: TODO: need comments for this register */
+	u8 power_seq[ILI9341_POWER_SEQ_LEN];
+	/* @dtca: TODO: need comments for this register */
+	u8 dtca[ILI9341_DTCA_LEN];
+	/* @dtcb: TODO: need comments for this register */
+	u8 dtcb[ILI9341_DTCB_LEN];
+	/* @power_a: TODO: need comments for this register */
+	u8 power_a[ILI9341_POWER_A_LEN];
+	/* @frc: Frame Rate Control (In Normal Mode/Full Colors) (B1h) */
+	u8 frc[ILI9341_FRC_LEN];
+	/* @prc: TODO: need comments for this register */
+	u8 prc;
+	/* @dfc_1: B6h DISCTRL (Display Function Control) */
+	u8 dfc_1[ILI9341_DFC_1_LEN];
+	/* @power_1: Power Control 1 (C0h) */
+	u8 power_1;
+	/* @power_2: Power Control 2 (C1h) */
+	u8 power_2;
+	/* @vcom_1: VCOM Control 1(C5h) */
+	u8 vcom_1[ILI9341_VCOM_1_LEN];
+	/* @vcom_2: VCOM Control 2(C7h) */
+	u8 vcom_2;
+	/* @address_mode: Memory Access Control (36h) */
+	u8 address_mode;
+	/* @g3amma_en: TODO: need comments for this register */
+	u8 g3amma_en;
+	/* @rgb_interface: RGB Interface Signal Control (B0h) */
+	u8 rgb_interface;
+	/* @dfc_2: refer to dfc_1 */
+	u8 dfc_2[ILI9341_DFC_2_LEN];
+	/* @column_addr: Column Address Set (2Ah) */
+	u8 column_addr[ILI9341_COLUMN_ADDR_LEN];
+	/* @page_addr: Page Address Set (2Bh) */
+	u8 page_addr[ILI9341_PAGE_ADDR_LEN];
+	/* @interface: Interface Control (F6h) */
+	u8 interface[ILI9341_INTERFACE_LEN];
+	/* @pixel_format: This command sets the pixel format for the RGB
+	 * image data used by
+	 */
+	u8 pixel_format;
+	/* @gamma_curve: This command is used to select the desired Gamma
+	 * curve for the
+	 */
+	u8 gamma_curve;
+	/* @pgamma: Positive Gamma Correction (E0h) */
+	u8 pgamma[ILI9341_PGAMMA_LEN];
+	/* @ngamma: Negative Gamma Correction (E1h) */
+	u8 ngamma[ILI9341_NGAMMA_LEN];
+};
+
+struct ili9341 {
+	struct device *dev;
+	const struct ili9341_config *conf;
+	struct drm_panel panel;
+	struct gpio_desc *reset_gpio;
+	struct gpio_desc *dc_gpio;
+	struct mipi_dbi *dbi;
+	u32 max_spi_speed;
+	struct regulator *vcc;
+};
+
+/*
+ * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
+ */
+static const struct ili9341_config ili9341_stm32f429_disco_data = {
+	.max_spi_speed = 10000000,
+	.mode = {
+		.clock = 6100,
+		.hdisplay = 240,
+		.hsync_start = 240 + 10,/* hfp 10 */
+		.hsync_end = 240 + 10 + 10,/* hsync 10 */
+		.htotal = 240 + 10 + 10 + 20,/* hbp 20 */
+		.vdisplay = 320,
+		.vsync_start = 320 + 4,/* vfp 4 */
+		.vsync_end = 320 + 4 + 2,/* vsync 2 */
+		.vtotal = 320 + 4 + 2 + 2,/* vbp 2 */
+		.flags = 0,
+		.width_mm = 65,
+		.height_mm = 50,
+		.type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED,
+	},
+	/* TODO: need comments for this register */
+	.ca = {0xc3, 0x08, 0x50},
+	/* TODO: need comments for this register */
+	.power_b = {0x00, 0xc1, 0x30},
+	/* TODO: need comments for this register */
+	.power_seq = {0x64, 0x03, 0x12, 0x81},
+	/* TODO: need comments for this register */
+	.dtca = {0x85, 0x00, 0x78},
+	/* TODO: need comments for this register */
+	.power_a = {0x39, 0x2c, 0x00, 0x34, 0x02},
+	/* TODO: need comments for this register */
+	.prc = 0x20,
+	/* TODO: need comments for this register */
+	.dtcb = {0x00, 0x00},
+	/* 0x00 fosc, 0x1b 70hz */
+	.frc = {0x00, 0x1b},
+	/* 0x0a Interval scan, AGND AGND AGND AGND
+	 * 0xa2 Normally white, G1 -> G320, S720 -> S1,
+	 *	Scan Cycle 5 frames,85ms
+	 */
+	.dfc_1 = {0x0a, 0xa2},
+	/* 0x10 3.65v */
+	.power_1 = 0x10,
+	/* 0x10 AVDD=vci*2, VGH=vci*7, VGL=-vci*4 */
+	.power_2 = 0x10,
+	/* 0x45 VCOMH 4.425v, 0x15 VCOML -1.975*/
+	.vcom_1 = {0x45, 0x15},
+	/* 0x90 offset voltage, VMH-48, VML-48 */
+	.vcom_2 = 0x90,
+	/* 0xc8 Row Address Order, Column Address Order
+	 * BGR 1
+	 */
+	.address_mode = 0xc8,
+	.g3amma_en = 0x00,
+	/* 0xc2
+	 * Display Data Path: Memory
+	 * RGB: DE mode
+	 * DOTCLK polarity set (data fetched at the falling time)
+	 */
+	.rgb_interface = ILI9341_RGB_DISP_PATH_MEM |
+			ILI9341_RGB_DE_MODE |
+			ILI9341_RGB_DPL,
+	/*
+	 * 0x0a
+	 * Gate outputs in non-display area: Interval scan
+	 * Determine source/VCOM output in a non-display area in the partial
+	 * display mode: AGND AGND AGND AGND
+	 *
+	 * 0xa7
+	 * Scan Cycle: 15 frames
+	 * fFLM = 60Hz: 255ms
+	 * Liquid crystal type: Normally white
+	 * Gate Output Scan Direction: G1 -> G320
+	 * Source Output Scan Direction: S720 -> S1
+	 *
+	 * 0x27
+	 * LCD Driver Line: 320 lines
+	 *
+	 * 0x04
+	 * PCDIV: 4
+	 */
+	.dfc_2 = {0x0a, 0xa7, 0x27, 0x04},
+	/* column address: 240 */
+	.column_addr = {0x00, 0x00, (ILI9341_COLUMN_ADDR >> 4) & 0xff,
+				ILI9341_COLUMN_ADDR & 0xff},
+	/* page address: 320 */
+	.page_addr = {0x00, 0x00, (ILI9341_PAGE_ADDR >> 4) & 0xff,
+				ILI9341_PAGE_ADDR & 0xff},
+	/* Memory write control: When the transfer number of data exceeds
+	 * (EC-SC+1)*(EP-SP+1), the column and page number will be
+	 * reset, and the exceeding data will be written into the following
+	 * column and page.
+	 * Display Operation Mode: RGB Interface Mode
+	 * Interface for RAM Access: RGB interface
+	 * 16- bit RGB interface (1 transfer/pixel)
+	 */
+	.interface = {ILI9341_IF_WE_MODE, 0x00,
+			ILI9341_IF_DM_RGB | ILI9341_IF_RM_RGB},
+	/* DPI: 16 bits / pixel */
+	.pixel_format = ILI9341_PIXEL_DPI_16_BITS,
+	/* Curve Selected: Gamma curve 1 (G2.2) */
+	.gamma_curve = ILI9341_GAMMA_CURVE_1,
+	.pgamma = {0x0f, 0x29, 0x24, 0x0c, 0x0e,
+			0x09, 0x4e, 0x78, 0x3c, 0x09,
+			0x13, 0x05, 0x17, 0x11, 0x00},
+	.ngamma = {0x00, 0x16, 0x1b, 0x04, 0x11,
+			0x07, 0x31, 0x33, 0x42, 0x05,
+			0x0c, 0x0a, 0x28, 0x2f, 0x0f},
+};
+
+static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
+{
+	return container_of(panel, struct ili9341, panel);
+}
+
+static void ili9341_dpi_init(struct ili9341 *ili)
+{
+	struct mipi_dbi *dbi = ili->dbi;
+	struct ili9341_config *cfg = (struct ili9341_config *)ili->conf;
+
+	/* Power Control */
+	mipi_dbi_command_stackbuf(dbi, 0xca, cfg->ca, ILI9341_CA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWERB, cfg->power_b,
+				  ILI9341_POWER_B_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWER_SEQ, cfg->power_seq,
+				  ILI9341_POWER_SEQ_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DTCA, cfg->dtca,
+				  ILI9341_DTCA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_POWERA, cfg->power_a,
+				  ILI9341_POWER_A_LEN);
+	mipi_dbi_command(ili->dbi, ILI9341_PRC, cfg->prc);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DTCB, cfg->dtcb,
+				  ILI9341_DTCB_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_FRC, cfg->frc, ILI9341_FRC_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_1,
+				  ILI9341_DFC_1_LEN);
+	mipi_dbi_command(dbi, ILI9341_POWER1, cfg->power_1);
+	mipi_dbi_command(dbi, ILI9341_POWER2, cfg->power_2);
+
+	/* VCOM */
+	mipi_dbi_command_stackbuf(dbi, ILI9341_VCOM1, cfg->vcom_1,
+				  ILI9341_VCOM_1_LEN);
+	mipi_dbi_command(dbi, ILI9341_VCOM2, cfg->vcom_2);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, cfg->address_mode);
+
+	/* Gamma */
+	mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, cfg->g3amma_en);
+	mipi_dbi_command(dbi, ILI9341_RGB_INTERFACE, cfg->rgb_interface);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_DFC, cfg->dfc_2,
+				  ILI9341_DFC_2_LEN);
+
+	/* Colomn address set */
+	mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_COLUMN_ADDRESS,
+				  cfg->column_addr, ILI9341_COLUMN_ADDR_LEN);
+
+	/* Page address set */
+	mipi_dbi_command_stackbuf(dbi, MIPI_DCS_SET_PAGE_ADDRESS,
+				  cfg->page_addr, ILI9341_PAGE_ADDR_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_INTERFACE, cfg->interface,
+				  ILI9341_INTERFACE_LEN);
+
+	/* Format */
+	mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT, cfg->pixel_format);
+	mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
+	msleep(200);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, cfg->gamma_curve);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_PGAMMA, cfg->pgamma,
+				  ILI9341_PGAMMA_LEN);
+	mipi_dbi_command_stackbuf(dbi, ILI9341_NGAMMA, cfg->ngamma,
+				  ILI9341_NGAMMA_LEN);
+	mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(200);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+	mipi_dbi_command(dbi, MIPI_DCS_WRITE_MEMORY_START);
+
+	dev_info(ili->dev, "initialized display rgb interface\n");
+}
+
+static int ili9341_dpi_power_on(struct ili9341 *ili)
+{
+	int ret = 0;
+
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Enable power */
+	if (!IS_ERR(ili->vcc)) {
+		ret = regulator_enable(ili->vcc);
+		if (ret < 0) {
+			dev_err(ili->dev, "unable to enable vcc\n");
+			return ret;
+		}
+	}
+	msleep(20);
+
+	/* De-assert RESET */
+	gpiod_set_value(ili->reset_gpio, 0);
+	msleep(20);
+
+	return 0;
+}
+
+static int ili9341_dpi_power_off(struct ili9341 *ili)
+{
+	/* Assert RESET */
+	gpiod_set_value(ili->reset_gpio, 1);
+
+	/* Disable power */
+	if (!IS_ERR(ili->vcc))
+		return regulator_disable(ili->vcc);
+
+	return 0;
+}
+
+static int ili9341_dpi_disable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_OFF);
+	return 0;
+}
+
+static int ili9341_dpi_unprepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	return ili9341_dpi_power_off(ili);
+}
+
+static int ili9341_dpi_prepare(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	int ret;
+
+	ret = ili9341_dpi_power_on(ili);
+	if (ret < 0)
+		return ret;
+
+	ili9341_dpi_init(ili);
+
+	return ret;
+}
+
+static int ili9341_dpi_enable(struct drm_panel *panel)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+
+	mipi_dbi_command(ili->dbi, MIPI_DCS_SET_DISPLAY_ON);
+	return 0;
+}
+
+static int ili9341_dpi_get_modes(struct drm_panel *panel,
+				 struct drm_connector *connector)
+{
+	struct ili9341 *ili = panel_to_ili9341(panel);
+	struct drm_device *drm = connector->dev;
+	struct drm_display_mode *mode;
+	struct drm_display_info *info;
+
+	info = &connector->display_info;
+	info->width_mm = ili->conf->mode.width_mm;
+	info->height_mm = ili->conf->mode.height_mm;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_DPL)
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_EPL)
+		info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
+	else
+		info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
+
+	mode = drm_mode_duplicate(drm, &ili->conf->mode);
+	if (!mode) {
+		DRM_ERROR("bad mode or failed to add mode\n");
+		return -EINVAL;
+	}
+	drm_mode_set_name(mode);
+
+	/* Set up the polarity */
+	if (ili->conf->rgb_interface & ILI9341_RGB_HSPL)
+		mode->flags |= DRM_MODE_FLAG_PHSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NHSYNC;
+
+	if (ili->conf->rgb_interface & ILI9341_RGB_VSPL)
+		mode->flags |= DRM_MODE_FLAG_PVSYNC;
+	else
+		mode->flags |= DRM_MODE_FLAG_NVSYNC;
+
+	drm_mode_probed_add(connector, mode);
+
+	return 1; /* Number of modes */
+}
+
+static const struct drm_panel_funcs ili9341_dpi_funcs = {
+	.disable = ili9341_dpi_disable,
+	.unprepare = ili9341_dpi_unprepare,
+	.prepare = ili9341_dpi_prepare,
+	.enable = ili9341_dpi_enable,
+	.get_modes = ili9341_dpi_get_modes,
+};
+
+static void ili9341_dbi_enable(struct drm_simple_display_pipe *pipe,
+			       struct drm_crtc_state *crtc_state,
+			       struct drm_plane_state *plane_state)
+{
+	struct mipi_dbi_dev *dbidev = drm_to_mipi_dbi_dev(pipe->crtc.dev);
+	struct mipi_dbi *dbi = &dbidev->dbi;
+	u8 addr_mode;
+	int ret, idx;
+
+	if (!drm_dev_enter(pipe->crtc.dev, &idx))
+		return;
+
+	DRM_DEBUG_KMS("\n");
+
+	ret = mipi_dbi_poweron_conditional_reset(dbidev);
+	if (ret < 0)
+		goto out_exit;
+	if (ret == 1)
+		goto out_enable;
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_OFF);
+
+	mipi_dbi_command(dbi, ILI9341_POWERB, 0x00, 0xc1, 0x30);
+	mipi_dbi_command(dbi, ILI9341_POWER_SEQ, 0x64, 0x03, 0x12, 0x81);
+	mipi_dbi_command(dbi, ILI9341_DTCA, 0x85, 0x00, 0x78);
+	mipi_dbi_command(dbi, ILI9341_POWERA, 0x39, 0x2c, 0x00, 0x34, 0x02);
+	mipi_dbi_command(dbi, ILI9341_PRC, ILI9341_DBI_PRC_NORMAL);
+	mipi_dbi_command(dbi, ILI9341_DTCB, 0x00, 0x00);
+
+	/* Power Control */
+	mipi_dbi_command(dbi, ILI9341_POWER1, ILI9341_DBI_VCOMH_4P6V);
+	mipi_dbi_command(dbi, ILI9341_POWER2, ILI9341_DBI_PWR_2_DEFAULT);
+	/* VCOM */
+	mipi_dbi_command(dbi, ILI9341_VCOM1, ILI9341_DBI_VCOM_1_VMH_4P25V,
+			 ILI9341_DBI_VCOM_1_VML_1P5V);
+	mipi_dbi_command(dbi, ILI9341_VCOM2, ILI9341_DBI_VCOM_2_DEC_58);
+
+	/* Memory Access Control */
+	mipi_dbi_command(dbi, MIPI_DCS_SET_PIXEL_FORMAT,
+			 MIPI_DCS_PIXEL_FMT_16BIT);
+
+	/* Frame Rate */
+	mipi_dbi_command(dbi, ILI9341_FRC, ILI9341_DBI_FRC_DIVA & 0x03,
+			 ILI9341_DBI_FRC_RTNA & 0x1f);
+
+	/* Gamma */
+	mipi_dbi_command(dbi, ILI9341_3GAMMA_EN, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_SET_GAMMA_CURVE, ILI9341_GAMMA_CURVE_1);
+	mipi_dbi_command(dbi, ILI9341_PGAMMA,
+			 0x0f, 0x31, 0x2b, 0x0c, 0x0e, 0x08, 0x4e, 0xf1,
+			 0x37, 0x07, 0x10, 0x03, 0x0e, 0x09, 0x00);
+	mipi_dbi_command(dbi, ILI9341_NGAMMA,
+			 0x00, 0x0e, 0x14, 0x03, 0x11, 0x07, 0x31, 0xc1,
+			 0x48, 0x08, 0x0f, 0x0c, 0x31, 0x36, 0x0f);
+
+	/* DDRAM */
+	mipi_dbi_command(dbi, ILI9341_ETMOD, ILI9341_DBI_EMS_GAS |
+			 ILI9341_DBI_EMS_DTS |
+			 ILI9341_DBI_EMS_GON);
+
+	/* Display */
+	mipi_dbi_command(dbi, ILI9341_DFC, 0x08, 0x82, 0x27, 0x00);
+	mipi_dbi_command(dbi, MIPI_DCS_EXIT_SLEEP_MODE);
+	msleep(100);
+
+	mipi_dbi_command(dbi, MIPI_DCS_SET_DISPLAY_ON);
+	msleep(100);
+
+out_enable:
+	switch (dbidev->rotation) {
+	default:
+		addr_mode = ILI9341_MADCTL_MX;
+		break;
+	case 90:
+		addr_mode = ILI9341_MADCTL_MV;
+		break;
+	case 180:
+		addr_mode = ILI9341_MADCTL_MY;
+		break;
+	case 270:
+		addr_mode = ILI9341_MADCTL_MV | ILI9341_MADCTL_MY |
+			    ILI9341_MADCTL_MX;
+		break;
+	}
+	addr_mode |= ILI9341_MADCTL_BGR;
+	mipi_dbi_command(dbi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode);
+	mipi_dbi_enable_flush(dbidev, crtc_state, plane_state);
+	DRM_DEBUG_KMS("initialized display serial interface\n");
+out_exit:
+	drm_dev_exit(idx);
+}
+
+static const struct drm_simple_display_pipe_funcs ili9341_dbi_funcs = {
+	.enable = ili9341_dbi_enable,
+	.disable = mipi_dbi_pipe_disable,
+	.update = mipi_dbi_pipe_update,
+	.prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
+};
+
+static const struct drm_display_mode ili9341_dbi_mode = {
+	DRM_SIMPLE_MODE(240, 320, 37, 49),
+};
+
+DEFINE_DRM_GEM_CMA_FOPS(ili9341_dbi_fops);
+
+static struct drm_driver ili9341_dbi_driver = {
+	.driver_features	= DRIVER_GEM | DRIVER_MODESET | DRIVER_ATOMIC,
+	.fops			= &ili9341_dbi_fops,
+	DRM_GEM_CMA_DRIVER_OPS_VMAP,
+	.debugfs_init		= mipi_dbi_debugfs_init,
+	.name			= "ili9341",
+	.desc			= "Ilitek ILI9341",
+	.date			= "20210716",
+	.major			= 1,
+	.minor			= 0,
+};
+
+static int _ili9341_probe(struct spi_device *spi, bool dpi)
+{
+	struct gpio_desc *dc;
+	struct gpio_desc *reset;
+	struct regulator *vcc;
+	struct device *dev = &spi->dev;
+	int ret;
+
+	reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(reset))
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'reset'\n");
+
+	dc = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
+	if (IS_ERR(dc))
+		DRM_DEV_ERROR(dev, "Failed to get gpio 'dc'\n");
+
+	vcc = devm_regulator_get_optional(dev, "vcc");
+	if (IS_ERR(vcc))
+		DRM_DEV_ERROR(dev, "get optional vcc failed\n");
+
+	if (!dpi) {
+		struct mipi_dbi_dev *dbidev;
+		struct mipi_dbi *dbi;
+		struct drm_device *drm;
+		u32 rotation = 0;
+
+		dbidev = devm_drm_dev_alloc(dev, &ili9341_dbi_driver,
+					    struct mipi_dbi_dev, drm);
+		if (IS_ERR(dbidev))
+			return PTR_ERR(dbidev);
+
+		dbi = &dbidev->dbi;
+		drm = &dbidev->drm;
+		dbi->reset = reset;
+		dbidev->regulator = vcc;
+
+		drm_mode_config_init(drm);
+		dbidev->backlight = devm_of_find_backlight(dev);
+		if (IS_ERR(dbidev->backlight))
+			return PTR_ERR(dbidev->backlight);
+
+		device_property_read_u32(dev, "rotation", &rotation);
+
+		ret = mipi_dbi_spi_init(spi, dbi, dc);
+		if (ret)
+			return ret;
+
+		ret = mipi_dbi_dev_init(dbidev, &ili9341_dbi_funcs,
+					&ili9341_dbi_mode, rotation);
+		if (ret)
+			return ret;
+
+		drm_mode_config_reset(drm);
+
+		ret = drm_dev_register(drm, 0);
+		if (ret)
+			return ret;
+
+		spi_set_drvdata(spi, drm);
+
+		drm_fbdev_generic_setup(drm, 0);
+	} else {
+		struct ili9341 *ili;
+
+		ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
+		if (!ili)
+			return -ENOMEM;
+
+		ili->dbi = devm_kzalloc(dev, sizeof(struct mipi_dbi),
+					GFP_KERNEL);
+		if (!ili->dbi)
+			return -ENOMEM;
+
+		ret = mipi_dbi_spi_init(spi, ili->dbi, dc);
+		if (ret)
+			return ret;
+
+		spi_set_drvdata(spi, ili);
+
+		ili->dev = dev;
+		ili->vcc = vcc;
+		ili->reset_gpio = reset;
+		/*
+		 * Every new incarnation of this display must have a unique
+		 * data entry for the system in this driver.
+		 */
+		ili->conf = of_device_get_match_data(dev);
+		if (!ili->conf) {
+			dev_err(dev, "missing device configuration\n");
+			return -ENODEV;
+		}
+
+		ili->max_spi_speed = ili->conf->max_spi_speed;
+
+		drm_panel_init(&ili->panel, dev, &ili9341_dpi_funcs,
+			       DRM_MODE_CONNECTOR_DPI);
+
+		drm_panel_add(&ili->panel);
+	}
+
+	return 0;
+}
+
+static int ili9341_probe(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t"))
+		return _ili9341_probe(spi, true);
+	else if (!strcmp(id->name, "yx240qv29"))
+		return _ili9341_probe(spi, false);
+
+	return -1;
+}
+
+static int ili9341_remove(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+	struct ili9341 *ili = spi_get_drvdata(spi);
+	struct drm_device *drm = spi_get_drvdata(spi);
+
+	if (!strcmp(id->name, "sf-tc240t-9370-t")) {
+		ili9341_dpi_power_off(ili);
+		drm_panel_remove(&ili->panel);
+	} else if (!strcmp(id->name, "yx240qv29")) {
+		drm_dev_unplug(drm);
+		drm_atomic_helper_shutdown(drm);
+	}
+	return 0;
+}
+
+static void ili9341_shutdown(struct spi_device *spi)
+{
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	if (!strcmp(id->name, "yx240qv29"))
+		drm_atomic_helper_shutdown(spi_get_drvdata(spi));
+}
+
+static const struct of_device_id ili9341_of_match[] = {
+	{
+		.compatible = "st,sf-tc240t-9370-t",
+		.data = &ili9341_stm32f429_disco_data,
+	},
+	{
+		/* porting from tiny/ili9341.c
+		 * for original mipi dbi compitable
+		 */
+		.compatible = "adafruit,yx240qv29",
+		.data = NULL,
+	},
+};
+MODULE_DEVICE_TABLE(of, ili9341_of_match);
+
+static const struct spi_device_id ili9341_id[] = {
+	{ "yx240qv29", 0 },
+	{ "sf-tc240t-9370-t", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, ili9341_id);
+
+static struct spi_driver ili9341_driver = {
+	.probe = ili9341_probe,
+	.remove = ili9341_remove,
+	.shutdown = ili9341_shutdown,
+	.id_table = ili9341_id,
+	.driver = {
+		.name = "panel-ilitek-ili9341",
+		.of_match_table = ili9341_of_match,
+	},
+};
+module_spi_driver(ili9341_driver);
+
+MODULE_AUTHOR("Dillon Min <dillon.minfei@gmail.com>");
+MODULE_DESCRIPTION("ILI9341 LCD panel driver");
+MODULE_LICENSE("GPL v2");
-- 
2.7.4


^ permalink raw reply related	[flat|nested] 9+ messages in thread

* Re: [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings
  2021-07-16 10:20 ` [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings dillon.minfei
@ 2021-07-18  0:16   ` Linus Walleij
       [not found]     ` <CAL9mu0JufzC_2p+X0PHdEpuYUqCNJ6XoT+f18oEsRa5Wm7wS3g@mail.gmail.com>
  2021-07-20  5:32   ` kernel test robot
  1 sibling, 1 reply; 9+ messages in thread
From: Linus Walleij @ 2021-07-18  0:16 UTC (permalink / raw)
  To: dillon min
  Cc: thierry.reding, Sam Ravnborg, Dave Airlie, Daniel Vetter,
	Rob Herring, Noralf Trønnes, Doug Anderson,
	Alexandre Torgue, open list:DRM PANEL DRIVERS,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	linux-kernel

Hi Dillon,

thanks for your patch!

On Fri, Jul 16, 2021 at 12:20 PM <dillon.minfei@gmail.com> wrote:

> From: Dillon Min <dillon.minfei@gmail.com>
>
> Add documentation for "ilitek,ili9341" panel.
>
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>

> +  dc-gpios:
> +    maxItems: 1
> +    description: Display data/command selection (D/CX)

This is a DBI feature so mention in the description that this is a
DBI panel.

> +  spi-3wire: true
> +
> +  spi-max-frequency:
> +    const: 10000000
> +
> +  port: true
> +
> +additionalProperties: false

Please add regulator supplies for the power lines, it's fine
not to implement code handling them in the driver but they
should be in the bindings.

For the ili9341 it should be

  vci-supply:
    description: Analog voltage supply (2.5 .. 3.3V)

  vddi-supply:
    description: Voltage supply for interface logic (1.65 .. 3.3 V)

  vddi-led-supply:
    description: Voltage supply for the LED driver (1.65 .. 3.3 V)

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver
  2021-07-16 10:20 ` [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver dillon.minfei
@ 2021-07-18  0:31   ` Linus Walleij
       [not found]     ` <CAL9mu0+C1p1mMEbw90Z66KCt1Rp2=GV=RcXgZizJRxu8rVaOGw@mail.gmail.com>
  0 siblings, 1 reply; 9+ messages in thread
From: Linus Walleij @ 2021-07-18  0:31 UTC (permalink / raw)
  To: dillon min
  Cc: thierry.reding, Sam Ravnborg, Dave Airlie, Daniel Vetter,
	Rob Herring, Noralf Trønnes, Doug Anderson,
	Alexandre Torgue, open list:DRM PANEL DRIVERS,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	linux-kernel

Hi Dillon,

thanks for your patch!

On Fri, Jul 16, 2021 at 12:20 PM <dillon.minfei@gmail.com> wrote:

> From: Dillon Min <dillon.minfei@gmail.com>
>
> This driver combine tiny/ili9341.c mipi_dbi_interface driver
> with mipi_dpi_interface driver, can support ili9341 with serial
> mode or parallel rgb interface mode by register configuration.
>
> Signed-off-by: Dillon Min <dillon.minfei@gmail.com>

Nice!

> +config DRM_PANEL_ILITEK_ILI9341
> +       tristate "Ilitek ILI9341 240x320 QVGA panels"
> +       depends on OF && SPI
> +       depends on DRM_KMS_HELPER
> +       depends on DRM_KMS_CMA_HELPER
(...)
> +#include <drm/drm_gem_framebuffer_helper.h>
> +#include <drm/drm_gem_cma_helper.h>
> +#include <drm/drm_fb_helper.h>
> +#include <drm/drm_gem_atomic_helper.h>
> +#include <drm/drm_atomic_helper.h>

Hm now there is a (partial) KMS driver in the panel driver, kinda, sorta.
Is this the right split? I'm not the best with DRM infrastructure,
just asking.

> +struct ili9341_config {
> +       u32 max_spi_speed;
> +       /** @mode: the drm display mode */
> +       const struct drm_display_mode mode;
> +       /* @ca: TODO: need comments for this register */
> +       u8 ca[ILI9341_CA_LEN];

These are all in the datasheet but I guess you plan to add these
TODOs later. (It's fine I suppose, the driver is already very nice.)

> +       struct regulator *vcc;

Use the right name of the pin for the regulator. I guess this is actually
vci. I would implement all three regulators and get them as bulk.
See e.g. drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
for an example on how to get and enable several regulators
using bulk.

The regulator framework will provide dummy regulators if you
didn't define some of them so it is fine to just provide one or two.

Yours,
Linus Walleij

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Re: [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings
  2021-07-16 10:20 ` [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings dillon.minfei
  2021-07-18  0:16   ` Linus Walleij
@ 2021-07-20  5:32   ` kernel test robot
       [not found]     ` <CAL9mu0LVdt1wtKzBa=201AJ-Eb4BdKtVx18hzQfaB0-Ga0jx9g@mail.gmail.com>
  1 sibling, 1 reply; 9+ messages in thread
From: kernel test robot @ 2021-07-20  5:32 UTC (permalink / raw)
  To: dillon.minfei, thierry.reding, sam, airlied, daniel, robh+dt,
	linus.walleij
  Cc: kbuild-all, devicetree, alexandre.torgue, linux-kernel, dri-devel

Hi,

Thank you for the patch! Perhaps something to improve:

[auto build test WARNING on robh/for-next]
[also build test WARNING on linus/master v5.14-rc2 next-20210719]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/dillon-minfei-gmail-com/Add-ilitek-ili9341-panel-driver/20210718-103113
base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
compiler: arm-linux-gnueabi-gcc (GCC) 10.3.0
reproduce: make ARCH=arm dtbs_check

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>


dtcheck warnings: (new ones prefixed by >>)
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /interrupt-controller@e000e100: failed to match any schema with compatible: ['arm,armv7m-nvic']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /timer@e000e010: failed to match any schema with compatible: ['arm,armv7m-systick']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/i2c@40005c00/stmpe811@41: failed to match any schema with compatible: ['st,stmpe811']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/i2c@40005c00/stmpe811@41/stmpe_touchscreen: failed to match any schema with compatible: ['st,stmpe-ts']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml: l3gd20@0: 'spi-max-frequency' does not match any of the regexes: 'pinctrl-[0-9]+'
   	From schema: Documentation/devicetree/bindings/iio/st,st-sensors.yaml
>> arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible: ['st,sf-tc240t-9370-t'] is too short
   	From schema: Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/crc@40023000: failed to match any schema with compatible: ['st,stm32f4-crc']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/rcc@40023800: failed to match any schema with compatible: ['st,stm32f42xx-rcc', 'st,stm32-rcc']
   arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/rcc@40023800: failed to match any schema with compatible: ['st,stm32f42xx-rcc', 'st,stm32-rcc']

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Fwd: [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings
       [not found]     ` <CAL9mu0JufzC_2p+X0PHdEpuYUqCNJ6XoT+f18oEsRa5Wm7wS3g@mail.gmail.com>
@ 2021-07-21  8:08       ` Dillon Min
  0 siblings, 0 replies; 9+ messages in thread
From: Dillon Min @ 2021-07-21  8:08 UTC (permalink / raw)
  To: Linux Kernel Mailing List,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS

Hi Linus,

Thanks for your detailed reply.

On Sun, 18 Jul 2021 at 08:17, Linus Walleij <linus.walleij@linaro.org> wrote:
>
> Hi Dillon,
>
> thanks for your patch!
>
> On Fri, Jul 16, 2021 at 12:20 PM <dillon.minfei@gmail.com> wrote:
>
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > Add documentation for "ilitek,ili9341" panel.
> >
> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
>
> > +  dc-gpios:
> > +    maxItems: 1
> > +    description: Display data/command selection (D/CX)
>
> This is a DBI feature so mention in the description that this is a
> DBI panel.


Okay, I will add the DBI panel to v2.

>
>
> > +  spi-3wire: true
> > +
> > +  spi-max-frequency:
> > +    const: 10000000
> > +
> > +  port: true
> > +
> > +additionalProperties: false
>
> Please add regulator supplies for the power lines, it's fine
> not to implement code handling them in the driver but they
> should be in the bindings.
>
> For the ili9341 it should be
>
>   vci-supply:
>     description: Analog voltage supply (2.5 .. 3.3V)
>
>   vddi-supply:
>     description: Voltage supply for interface logic (1.65 .. 3.3 V)
>
>   vddi-led-supply:
>     description: Voltage supply for the LED driver (1.65 .. 3.3 V)
>

Thanks so much, I will add it to v2.

>
> Yours,
> Linus Walleij

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Fwd: [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings
       [not found]     ` <CAL9mu0LVdt1wtKzBa=201AJ-Eb4BdKtVx18hzQfaB0-Ga0jx9g@mail.gmail.com>
@ 2021-07-21  8:11       ` Dillon Min
  0 siblings, 0 replies; 9+ messages in thread
From: Dillon Min @ 2021-07-21  8:11 UTC (permalink / raw)
  To: open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
	Linux Kernel Mailing List

Hi Kernel test robot,

Thanks for your time to test my patch.

I did the dtbs_check on my side, and got the same warnings.

But I guess these warnings do not come from this submission,
So, I will not be going to fix it at this time, but will at other submissions
to fix these, add arm,armv7m-nvic.yaml ... to describe compatibles, etc.

by the way, i did find a warning from the stm32f429-disco.dts and fixt it
in "[PATCH v2 2/3] ARM: dts: stm32: fix dtbs_check warning on ili9341
dts binding",

the warning:
arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible:
['st,sf-tc240t-9370-t'] is too short

my make command:
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml

Best regards
thanks

Dillon

On Tue, 20 Jul 2021 at 14:12, kernel test robot <lkp@intel.com> wrote:
>
> Hi,
>
> Thank you for the patch! Perhaps something to improve:
>
> [auto build test WARNING on robh/for-next]
> [also build test WARNING on linus/master v5.14-rc2 next-20210719]
> [If your patch is applied to the wrong git tree, kindly drop us a note.
> And when submitting patch, we suggest to use '--base' as documented in
> https://git-scm.com/docs/git-format-patch]
>
> url:    https://github.com/0day-ci/linux/commits/dillon-minfei-gmail-com/Add-ilitek-ili9341-panel-driver/20210718-103113
> base:   https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next
> compiler: arm-linux-gnueabi-gcc (GCC) 10.3.0
> reproduce: make ARCH=arm dtbs_check
>
> If you fix the issue, kindly add following tag as appropriate
> Reported-by: kernel test robot <lkp@intel.com>
>
>
> dtcheck warnings: (new ones prefixed by >>)
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /interrupt-controller@e000e100: failed to match any schema with compatible: ['arm,armv7m-nvic']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /timer@e000e010: failed to match any schema with compatible: ['arm,armv7m-systick']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/i2c@40005c00/stmpe811@41: failed to match any schema with compatible: ['st,stmpe811']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/i2c@40005c00/stmpe811@41/stmpe_touchscreen: failed to match any schema with compatible: ['st,stmpe-ts']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml: l3gd20@0: 'spi-max-frequency' does not match any of the regexes: 'pinctrl-[0-9]+'
>         From schema: Documentation/devicetree/bindings/iio/st,st-sensors.yaml
> >> arch/arm/boot/dts/stm32f429-disco.dt.yaml: display@1: compatible: ['st,sf-tc240t-9370-t'] is too short
>         From schema: Documentation/devicetree/bindings/display/panel/ilitek,ili9341.yaml
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/crc@40023000: failed to match any schema with compatible: ['st,stm32f4-crc']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/rcc@40023800: failed to match any schema with compatible: ['st,stm32f42xx-rcc', 'st,stm32-rcc']
>    arch/arm/boot/dts/stm32f429-disco.dt.yaml:0:0: /soc/rcc@40023800: failed to match any schema with compatible: ['st,stm32f42xx-rcc', 'st,stm32-rcc']
>
> ---
> 0-DAY CI Kernel Test Service, Intel Corporation
> https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

^ permalink raw reply	[flat|nested] 9+ messages in thread

* Fwd: [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver
       [not found]     ` <CAL9mu0+C1p1mMEbw90Z66KCt1Rp2=GV=RcXgZizJRxu8rVaOGw@mail.gmail.com>
@ 2021-07-21  8:13       ` Dillon Min
  0 siblings, 0 replies; 9+ messages in thread
From: Dillon Min @ 2021-07-21  8:13 UTC (permalink / raw)
  To: Linux Kernel Mailing List,
	open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS

Hi Linus,

Thanks for your detailed review.

On Sun, 18 Jul 2021 at 08:31, Linus Walleij <linus.walleij@linaro.org> wrote:
>
> Hi Dillon,
>
> thanks for your patch!
>
> On Fri, Jul 16, 2021 at 12:20 PM <dillon.minfei@gmail.com> wrote:
>
> > From: Dillon Min <dillon.minfei@gmail.com>
> >
> > This driver combine tiny/ili9341.c mipi_dbi_interface driver
> > with mipi_dpi_interface driver, can support ili9341 with serial
> > mode or parallel rgb interface mode by register configuration.
> >
> > Signed-off-by: Dillon Min <dillon.minfei@gmail.com>
>
> Nice!
>
> > +config DRM_PANEL_ILITEK_ILI9341
> > +       tristate "Ilitek ILI9341 240x320 QVGA panels"
> > +       depends on OF && SPI
> > +       depends on DRM_KMS_HELPER
> > +       depends on DRM_KMS_CMA_HELPER
> (...)
> > +#include <drm/drm_gem_framebuffer_helper.h>
> > +#include <drm/drm_gem_cma_helper.h>
> > +#include <drm/drm_fb_helper.h>
> > +#include <drm/drm_gem_atomic_helper.h>
> > +#include <drm/drm_atomic_helper.h>
>
> Hm now there is a (partial) KMS driver in the panel driver, kinda, sorta.
> Is this the right split? I'm not the best with DRM infrastructure,
> just asking.


I tried to remove one of these two headers, but got compile errors:

linux/drivers/gpu/drm/panel/panel-ilitek-ili9341.c:719:3: error:
implicit declaration of function 'drm_atomic_helper_shutdown'
[-Werror=implicit-function-declaration]
  719 |   drm_atomic_helper_shutdown(drm);
      |   ^~~~~~~~~~~~~~~~~~~~~~~~~~
or

linux/drivers/gpu/drm/panel/panel-ilitek-ili9341.c:562:16: error:
'drm_gem_simple_display_pipe_prepare_fb' undeclared here (not in a
function)
  562 |  .prepare_fb = drm_gem_simple_display_pipe_prepare_fb,
      |                ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Actually, these two headers are merged from tiny/ili9341.c to support
only-DBI interface, I'm
not sure whether the maintainers will ask me to remove
(tiny/ili9341.c) code from this patch.
If so, I will remove these headers.

But, It's a little strange to support different interfaces from
different drivers.

>
> > +struct ili9341_config {
> > +       u32 max_spi_speed;
> > +       /** @mode: the drm display mode */
> > +       const struct drm_display_mode mode;
> > +       /* @ca: TODO: need comments for this register */
> > +       u8 ca[ILI9341_CA_LEN];
>
> These are all in the datasheet but I guess you plan to add these
> TODOs later. (It's fine I suppose, the driver is already very nice.)


Yes, I didn't get detailed information about these registers from this
panel datasheet, so leave TODOs here.

>
> > +       struct regulator *vcc;
>
> Use the right name of the pin for the regulator. I guess this is actually
> vci. I would implement all three regulators and get them as bulk.
> See e.g. drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
> for an example on how to get and enable several regulators
> using bulk.
>
> The regulator framework will provide dummy regulators if you
> didn't define some of them so it is fine to just provide one or two.
>

Really appreciate your suggestion, will add to v2.

>
> Yours,
> Linus Walleij

^ permalink raw reply	[flat|nested] 9+ messages in thread

end of thread, other threads:[~2021-07-21  8:26 UTC | newest]

Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-16 10:20 [PATCH 0/2] Add ilitek ili9341 panel driver dillon.minfei
2021-07-16 10:20 ` [PATCH 1/2] dt-bindings: display: panel: Add ilitek ili9341 panel bindings dillon.minfei
2021-07-18  0:16   ` Linus Walleij
     [not found]     ` <CAL9mu0JufzC_2p+X0PHdEpuYUqCNJ6XoT+f18oEsRa5Wm7wS3g@mail.gmail.com>
2021-07-21  8:08       ` Fwd: " Dillon Min
2021-07-20  5:32   ` kernel test robot
     [not found]     ` <CAL9mu0LVdt1wtKzBa=201AJ-Eb4BdKtVx18hzQfaB0-Ga0jx9g@mail.gmail.com>
2021-07-21  8:11       ` Fwd: " Dillon Min
2021-07-16 10:20 ` [PATCH 2/2] drm/panel: Add ilitek ili9341 panel driver dillon.minfei
2021-07-18  0:31   ` Linus Walleij
     [not found]     ` <CAL9mu0+C1p1mMEbw90Z66KCt1Rp2=GV=RcXgZizJRxu8rVaOGw@mail.gmail.com>
2021-07-21  8:13       ` Fwd: " Dillon Min

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).