From mboxrd@z Thu Jan  1 00:00:00 1970
Return-Path: <linux-kernel-owner@vger.kernel.org>
Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand
        id S1752614AbeEOJZm (ORCPT <rfc822;w@1wt.eu>);
        Tue, 15 May 2018 05:25:42 -0400
Received: from mail-it0-f65.google.com ([209.85.214.65]:54701 "EHLO
        mail-it0-f65.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org
        with ESMTP id S1752390AbeEOJZj (ORCPT
        <rfc822;linux-kernel@vger.kernel.org>);
        Tue, 15 May 2018 05:25:39 -0400
X-Google-Smtp-Source: AB8JxZq+2Gzj971T8+7U0nCw0m3KxJNEmkki4QgSJfYLY5eOEvzqr5vblUNseOBigC6Ky6DOM0ksZ6LqvaCty12/+k8=
MIME-Version: 1.0
In-Reply-To: <CAHCN7xJ6+vmyrTQGYH=pKz5GRf7rLT4otreNgu6TJi_3UAEX5w@mail.gmail.com>
References: <20180509172606.29387-1-david@lechnology.com> <CAHCN7xJ6+vmyrTQGYH=pKz5GRf7rLT4otreNgu6TJi_3UAEX5w@mail.gmail.com>
From: Bartosz Golaszewski <brgl@bgdev.pl>
Date: Tue, 15 May 2018 11:25:38 +0200
Message-ID: <CAMRc=MdO0EtzDHp3RF4ym3umWM_KfhvpWHV2+Y3270ygKz9iGw@mail.gmail.com>
Subject: =?UTF-8?Q?Re=3A_=5BPATCH_v10_00=2F27=5D_ARM=3A_davinci=3A_convert_to_commo?=
        =?UTF-8?Q?n_clock_framework=E2=80=8B?=
To: Adam Ford <aford173@gmail.com>
Cc: David Lechner <david@lechnology.com>,
        linux-clk <linux-clk@vger.kernel.org>,
        devicetree <devicetree@vger.kernel.org>,
        arm-soc <linux-arm-kernel@lists.infradead.org>,
        Michael Turquette <mturquette@baylibre.com>,
        Stephen Boyd <sboyd@codeaurora.org>, Rob Herring <robh+dt@kernel.org>,
        Mark Rutland <mark.rutland@arm.com>, Sekhar Nori <nsekhar@ti.com>,
        Kevin Hilman <khilman@kernel.org>,
        Bartosz Golaszewski <bgolaszewski@baylibre.com>,
        Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Content-Type: text/plain; charset="UTF-8"
Sender: linux-kernel-owner@vger.kernel.org
List-ID: <linux-kernel.vger.kernel.org>
X-Mailing-List: linux-kernel@vger.kernel.org

2018-05-14 2:40 GMT+02:00 Adam Ford <aford173@gmail.com>:
> On Wed, May 9, 2018 at 12:25 PM, David Lechner <david@lechnology.com> wrote:
>> This series converts mach-davinci to use the common clock framework.
>>
>> The series works like this, the first 3 patches fix some issues with the clock
>> drivers that have already been accepted into the mainline kernel.
>>
>> Then, starting with "ARM: davinci: pass clock as parameter to
>> davinci_timer_init()", we get the mach code ready for the switch by adding the
>> code needed for the new clock drivers and adding #ifndef CONFIG_COMMON_CLK
>> around the legacy clocks so that we can switch easily between the old and the
>> new.
>>
>> "ARM: davinci: switch to common clock framework" actually flips the switch
>> to start using the new clock drivers. Then the next 8 patches remove all
>> of the old clock code.
>>
>> The final four patches add device tree clock support to the one SoC that
>> supports it.
>>
>> This series has been tested on TI OMAP-L138 LCDK (both device tree and legacy
>> board file).
>>
>
> I am not sure if I did something wrong, but I attempted to build and I
> wasn't able to boot the da850-evm.dtb your repo common-clk-v11,
> however the legacy board file boot was OK.
>
> make davinci_all_defconfig ARCH=arm
> make zImage modules da850-evm.dtb ARCH=arm CROSS_COMPILE=arm-linux- -j8
>
> 3140416 bytes read in 1464 ms (2 MiB/s)
> 20353 bytes read in 15 ms (1.3 MiB/s)
> ## Flattened Device Tree blob at c0600000
>    Booting using the fdt blob at 0xc0600000
>    Loading Device Tree to c7e57000, end c7e5ef80 ... OK
>
> Starting kernel ...
>
> Uncompressing Linux... done, booting the kernel.
>
> (and hang)
>
> If you have some suggestions, I am try them as I get time.
>
> adam
>

Runs fine on da850-lcdk and dm365-evm. I'll test the da850-evm
tomorrow when I'll have access to it.

Bart