From: Amit Kucheria <amit.kucheria@linaro.org>
To: Eduardo Valentin <edubezval@gmail.com>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Andy Gross <andy.gross@linaro.org>,
vkoul@kernel.org,
Khasim Syed Mohammed <khasim.mohammed@linaro.org>,
David Brown <david.brown@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>
Subject: Re: [PATCH v3 4/4] arm64: dts: qcom: qcs404: Add thermal zones for each sensor
Date: Tue, 4 Dec 2018 16:56:15 +0530 [thread overview]
Message-ID: <CAP245DXz=6vCoB+ssV6kBEk-vqSmVTFnsRJxDoGUd_JmPZv0jg@mail.gmail.com> (raw)
In-Reply-To: <20181129165709.GF2688@localhost.localdomain>
On Thu, Nov 29, 2018 at 10:27 PM Eduardo Valentin <edubezval@gmail.com> wrote:
>
> On Tue, Nov 27, 2018 at 09:59:07PM +0530, Amit Kucheria wrote:
> > qcs404 has 10 sensors connected to the single TSENS IP. Define a thermal
> > zone for each of those sensors to expose the temperature of each zone.
> >
> > Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
> > Reviewed-by: Vinod Koul <vkoul@kernel.org>
> > Tested-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > arch/arm64/boot/dts/qcom/qcs404.dtsi | 206 +++++++++++++++++++++++++++
> > 1 file changed, 206 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> > index 57d14d8f0c90..cbc3fd378893 100644
> > --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
> > +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> > @@ -30,6 +30,7 @@
> > reg = <0x100>;
> > enable-method = "psci";
> > next-level-cache = <&L2_0>;
> > + #cooling-cells= <2>;
> > };
> >
> > CPU1: cpu@101 {
> > @@ -38,6 +39,7 @@
> > reg = <0x101>;
> > enable-method = "psci";
> > next-level-cache = <&L2_0>;
> > + #cooling-cells= <2>;
> > };
> >
> > CPU2: cpu@102 {
> > @@ -46,6 +48,7 @@
> > reg = <0x102>;
> > enable-method = "psci";
> > next-level-cache = <&L2_0>;
> > + #cooling-cells= <2>;
> > };
> >
> > CPU3: cpu@103 {
> > @@ -54,6 +57,7 @@
> > reg = <0x103>;
> > enable-method = "psci";
> > next-level-cache = <&L2_0>;
> > + #cooling-cells= <2>;
> > };
> >
> > L2_0: l2-cache {
> > @@ -507,4 +511,206 @@
> > #interrupt-cells = <2>;
> > };
> > };
> > +
> > + thermal-zones {
> > + aoss-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 0>;
> > +
> > + trips {
> > + aoss_alert: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
>
>
> A passive trip and yet no cooling map associate to it..
Oops, was waiting for cpufreq to be enabled on the platform. I'll get
rid of the trips for now.
>
> > + };
> > + aoss_crit: trip1 {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + dsp-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 1>;
> > +
> > + trips {
> > + dsp_alert: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + dsp_crit: trip1 {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + lpass-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 2>;
> > +
> > + trips {
> > + lpass_alert: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + lpass_crit: trip1 {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + wlan-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 3>;
> > +
> > + trips {
> > + wlan_alert: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + wlan_crit: trip1 {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + cluster-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 4>;
> > +
> > + trips {
> > + cluster_alert: cluster_alert {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cluster_crit: cluster_crit {
> > + temperature = <110000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + cpu-thermal0 {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 5>;
> > +
> > + trips {
> > + cpu_alert0: cpu_alert0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cpu_crit0: cpu_crit0 {
> > + temperature = <110000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + cpu-thermal1 {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 6>;
> > +
> > + trips {
> > + cpu_alert1: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cpu_crit1: trip1 {
> > + temperature = <110000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + cpu-thermal2 {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 7>;
> > +
> > + trips {
> > + cpu_alert2: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cpu_crit2: trip1 {
> > + temperature = <110000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + cpu-thermal3 {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 8>;
> > +
> > + trips {
> > + cpu_alert3: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cpu_crit3: trip1 {
> > + temperature = <110000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > +
> > + gpu-thermal {
> > + polling-delay-passive = <250>;
> > + polling-delay = <1000>;
> > +
> > + thermal-sensors = <&tsens 9>;
> > +
> > + trips {
> > + gpu_alert: trip0 {
> > + temperature = <75000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + gpu_crit: trip1 {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
> > + };
> > };
> > --
> > 2.17.1
> >
next prev parent reply other threads:[~2018-12-04 11:26 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-27 16:29 [PATCH v3 0/4] thermal: tsens: Add support for QCS404 platform Amit Kucheria
2018-11-27 16:29 ` [PATCH v3 1/4] dt: thermal: tsens: Add bindings for qcs404 Amit Kucheria
2018-11-27 16:29 ` [PATCH v3 2/4] drivers: thermal: tsens: Add generic support for TSENS v1 IP Amit Kucheria
2018-11-29 16:56 ` Eduardo Valentin
2018-12-04 11:24 ` Amit Kucheria
2018-12-04 16:43 ` Eduardo Valentin
2018-11-27 16:29 ` [PATCH v3 3/4] arm64: dts: qcom: qcs404: Add tsens controller Amit Kucheria
2018-11-27 16:29 ` [PATCH v3 4/4] arm64: dts: qcom: qcs404: Add thermal zones for each sensor Amit Kucheria
2018-11-29 16:57 ` Eduardo Valentin
2018-12-04 11:26 ` Amit Kucheria [this message]
2018-12-04 16:36 ` Eduardo Valentin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to='CAP245DXz=6vCoB+ssV6kBEk-vqSmVTFnsRJxDoGUd_JmPZv0jg@mail.gmail.com' \
--to=amit.kucheria@linaro.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=edubezval@gmail.com \
--cc=khasim.mohammed@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).