* [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755
@ 2021-07-22 5:14 Jason Lai
2021-08-02 16:22 ` Ulf Hansson
0 siblings, 1 reply; 4+ messages in thread
From: Jason Lai @ 2021-07-22 5:14 UTC (permalink / raw)
To: ulf.hansson, adrian.hunter
Cc: linux-mmc, linux-kernel, ben.chuang, greg.tu, AKASHI Takahiro
Summary
=======
In these patches we focus on uhs2 side to address Ulf's suggestion which
was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
Ulf's expection.
Please review this series (particularly Patch 29/29).
Thanks.
-Jason Lai
------ original cover letter from v3 ------
This is an interim snapshot of our next version, v4, for enabling
UHS-II on MMC/SD.
It is focused on 'sdhci' side to address Adrian's comments regarding
"modularising" sdhci-uhs2.c.
The whole aim of this version is to get early feedback from Adrian (and
others) on this issue. Without any consensus about the code structure,
it would make little sense to go further ahead on sdhci side.
(Actually, Adrian has made no comments other than "modularising" so far.)
I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
set to meet what I believe Adrian expects; no UHS-II related code in
Legacy (UHS-I) code or sdhci.c.
Nevertheless, almost of all changes I made are trivial and straightforward
in this direction, and I believe that there is no logic changed since v3
except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
command sequences in addition to UHS-II errors. So I added extra handlings.
I admit that there is plenty of room for improvements (for example,
handling host->flags), but again the focal point here is how sdhci-uhs2.c
should be built as a module.
Please review this series (particularly Patch#8-#26 and #27) from this
viewpoint in the first place.
(Ben is working on 'host' side but there is no change on 'host' side
in this submission except a minor tweak.)
Thanks,
-Takahiro Akashi
------ original cover letter from v3 ------
Summary
=======
These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
About UHS-II, roughly deal with the following three parts:
1) A UHS-II detection and initialization:
- Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
[2]).
- Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
- In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
Setup Sequence.
2) Send Legacy SD command through SD-TRAN
- Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
Types and Format Overview[3]).
- Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
3) UHS-II Interrupt
- Except for UHS-II error interrupts, most interrupts share the original
interrupt registers.
Patch structure
===============
patch#1-#7: for core
patch#8-#17: for sdhci
patch#18-#21: for GL9755
Tests
=====
Ran 'dd' command to evaluate the performance:
(SanDisk UHS-II card on GL9755 controller)
Read Write
UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
UHS-II enabled : 206MB/s 80MB/s
TODO
====
- replace some define with BIT macro
Reference
=========
[1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
[2] SD Host Controller Simplified Specification 4.20
[3] UHS-II Simplified Addendum 1.02
Changes in v3 (Jul. 10, 2020)
* rebased to v5.8-rc4
* add copyright notice
* reorganize the patch set and split some commits into smaller ones
* separate uhs-2 headers from others
* correct wrong spellings
* fix most of checkpatch warnings/errors
* remove all k[cz]alloc() from the code
* guard sdhci-uhs2 specific code with
'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
* make sdhci-uhs2.c as a module
* trivial changes, including
- rename back sdhci-core.c to sdhci.c
- allow vendor code to disable uhs2 if v4_mode == 0
in __sdhci_add_host()
- merge uhs2_power_up() into mmc_power_up()
- remove flag_uhs2 from mmc_attach_sd()
- add function descriptions to EXPORT'ed functions
- other minor code optimization
Changes in v2 (Jan. 9, 2020)
* rebased to v5.5-rc5
AKASHI Takahiro (23):
mmc: core: UHS-II support, modify power-up sequence
mmc: core: UHS-II support, skip set_chip_select()
mmc: core: UHS-II support, skip TMODE setup in some cases
mmc: core: UHS-II support, generate UHS-II SD command packet
mmc: core: UHS-II support, set APP_CMD bit if necessary
mmc: sdhci: add a kernel configuration for enabling UHS-II support
mmc: sdhci: add UHS-II related definitions in headers
mmc: sdhci: add UHS-II module
mmc: sdhci-uhs2: dump UHS-II registers
mmc: sdhci-uhs2: add reset function
mmc: sdhci-uhs2: add set_power() to support vdd2
mmc: sdhci-uhs2: skip signal_voltage_switch()
mmc: sdhci-uhs2: add set_timeout()
mmc: sdhci-uhs2: add set_ios()
mmc: sdhci-uhs2: add detect_init() to detect the interface
mmc: sdhci-uhs2: add clock operations
mmc: sdhci-uhs2: add set_reg() to initialise the interface
mmc: sdhci-uhs2: add request() and others
mmc: sdhci-uhs2: add irq() and others
mmc: sdhci-uhs2: add add_host() and others to set up the driver
mmc: core: add post-mmc_attach_sd hook
mmc: sdhci-pci: add UHS-II support framework
mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
Ben Chuang (4):
mmc: add UHS-II related definitions in public headers
mmc: core: UHS-II support, try to select UHS-II interface
mmc: sdhci-uhs2: add pre-detect_init hook
mmc: sdhci-uhs2: add post-mmc_attach_sd hook
drivers/mmc/core/Makefile | 2 +-
drivers/mmc/core/block.c | 7 +-
drivers/mmc/core/bus.c | 5 +-
drivers/mmc/core/core.c | 118 +-
drivers/mmc/core/regulator.c | 14 +
drivers/mmc/core/sd.c | 32 +
drivers/mmc/core/sd_ops.c | 12 +
drivers/mmc/core/uhs2.c | 883 +++++++++++++++
drivers/mmc/core/uhs2.h | 21 +
drivers/mmc/host/Kconfig | 10 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-pci-core.c | 16 +-
drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
drivers/mmc/host/sdhci-pci.h | 3 +
drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
drivers/mmc/host/sdhci-uhs2.h | 224 ++++
drivers/mmc/host/sdhci.c | 333 +++---
drivers/mmc/host/sdhci.h | 117 +-
include/linux/mmc/card.h | 1 +
include/linux/mmc/core.h | 6 +
include/linux/mmc/host.h | 31 +
include/linux/mmc/uhs2.h | 268 +++++
22 files changed, 3961 insertions(+), 158 deletions(-)
create mode 100644 drivers/mmc/core/uhs2.c
create mode 100644 drivers/mmc/core/uhs2.h
create mode 100644 drivers/mmc/host/sdhci-uhs2.c
create mode 100644 drivers/mmc/host/sdhci-uhs2.h
create mode 100644 include/linux/mmc/uhs2.h
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755
2021-07-22 5:14 [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755 Jason Lai
@ 2021-08-02 16:22 ` Ulf Hansson
2021-08-06 6:37 ` Lai Jason
0 siblings, 1 reply; 4+ messages in thread
From: Ulf Hansson @ 2021-08-02 16:22 UTC (permalink / raw)
To: Jason Lai
Cc: Adrian Hunter, linux-mmc, Linux Kernel Mailing List, Ben Chuang,
GregTu[杜啟軒],
AKASHI Takahiro
On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@gmail.com> wrote:
>
> Summary
> =======
> In these patches we focus on uhs2 side to address Ulf's suggestion which
> was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
>
>
> I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> Ulf's expection.
>
> Please review this series (particularly Patch 29/29).
I think you have misunderstood the intent with the series that I
posted [1] a while ago. The idea was to add the foundation of what
should be needed in the mmc core to support UHS-II cards. Note, it's
only the foundation, not the complete code.
In other words, I think you should base the next version of $subject
series *on top* of my series [1], rather than the opposite.
Moreover, next time, please try to better describe in each changelog
and in a cover letter what you have changed and why, as it helps me to
review.
Kind regards
Uffe
[1]
https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
>
> Thanks.
> -Jason Lai
>
> ------ original cover letter from v3 ------
> This is an interim snapshot of our next version, v4, for enabling
> UHS-II on MMC/SD.
>
> It is focused on 'sdhci' side to address Adrian's comments regarding
> "modularising" sdhci-uhs2.c.
> The whole aim of this version is to get early feedback from Adrian (and
> others) on this issue. Without any consensus about the code structure,
> it would make little sense to go further ahead on sdhci side.
> (Actually, Adrian has made no comments other than "modularising" so far.)
>
> I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> set to meet what I believe Adrian expects; no UHS-II related code in
> Legacy (UHS-I) code or sdhci.c.
>
> Nevertheless, almost of all changes I made are trivial and straightforward
> in this direction, and I believe that there is no logic changed since v3
> except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> command sequences in addition to UHS-II errors. So I added extra handlings.
>
> I admit that there is plenty of room for improvements (for example,
> handling host->flags), but again the focal point here is how sdhci-uhs2.c
> should be built as a module.
>
> Please review this series (particularly Patch#8-#26 and #27) from this
> viewpoint in the first place.
> (Ben is working on 'host' side but there is no change on 'host' side
> in this submission except a minor tweak.)
>
> Thanks,
> -Takahiro Akashi
>
> ------ original cover letter from v3 ------
> Summary
> =======
> These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
>
> About UHS-II, roughly deal with the following three parts:
> 1) A UHS-II detection and initialization:
> - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
> [2]).
> - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
> 3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
> Setup Sequence.
>
> 2) Send Legacy SD command through SD-TRAN
> - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
> compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
> Types and Format Overview[3]).
> - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
> CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
>
> 3) UHS-II Interrupt
> - Except for UHS-II error interrupts, most interrupts share the original
> interrupt registers.
>
> Patch structure
> ===============
> patch#1-#7: for core
> patch#8-#17: for sdhci
> patch#18-#21: for GL9755
>
> Tests
> =====
> Ran 'dd' command to evaluate the performance:
> (SanDisk UHS-II card on GL9755 controller)
> Read Write
> UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> UHS-II enabled : 206MB/s 80MB/s
>
> TODO
> ====
> - replace some define with BIT macro
>
> Reference
> =========
> [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> [2] SD Host Controller Simplified Specification 4.20
> [3] UHS-II Simplified Addendum 1.02
>
> Changes in v3 (Jul. 10, 2020)
> * rebased to v5.8-rc4
> * add copyright notice
> * reorganize the patch set and split some commits into smaller ones
> * separate uhs-2 headers from others
> * correct wrong spellings
> * fix most of checkpatch warnings/errors
> * remove all k[cz]alloc() from the code
> * guard sdhci-uhs2 specific code with
> 'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> * make sdhci-uhs2.c as a module
> * trivial changes, including
> - rename back sdhci-core.c to sdhci.c
> - allow vendor code to disable uhs2 if v4_mode == 0
> in __sdhci_add_host()
> - merge uhs2_power_up() into mmc_power_up()
> - remove flag_uhs2 from mmc_attach_sd()
> - add function descriptions to EXPORT'ed functions
> - other minor code optimization
>
> Changes in v2 (Jan. 9, 2020)
> * rebased to v5.5-rc5
>
> AKASHI Takahiro (23):
> mmc: core: UHS-II support, modify power-up sequence
> mmc: core: UHS-II support, skip set_chip_select()
> mmc: core: UHS-II support, skip TMODE setup in some cases
> mmc: core: UHS-II support, generate UHS-II SD command packet
> mmc: core: UHS-II support, set APP_CMD bit if necessary
> mmc: sdhci: add a kernel configuration for enabling UHS-II support
> mmc: sdhci: add UHS-II related definitions in headers
> mmc: sdhci: add UHS-II module
> mmc: sdhci-uhs2: dump UHS-II registers
> mmc: sdhci-uhs2: add reset function
> mmc: sdhci-uhs2: add set_power() to support vdd2
> mmc: sdhci-uhs2: skip signal_voltage_switch()
> mmc: sdhci-uhs2: add set_timeout()
> mmc: sdhci-uhs2: add set_ios()
> mmc: sdhci-uhs2: add detect_init() to detect the interface
> mmc: sdhci-uhs2: add clock operations
> mmc: sdhci-uhs2: add set_reg() to initialise the interface
> mmc: sdhci-uhs2: add request() and others
> mmc: sdhci-uhs2: add irq() and others
> mmc: sdhci-uhs2: add add_host() and others to set up the driver
> mmc: core: add post-mmc_attach_sd hook
> mmc: sdhci-pci: add UHS-II support framework
> mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
>
> Ben Chuang (4):
> mmc: add UHS-II related definitions in public headers
> mmc: core: UHS-II support, try to select UHS-II interface
> mmc: sdhci-uhs2: add pre-detect_init hook
> mmc: sdhci-uhs2: add post-mmc_attach_sd hook
>
> drivers/mmc/core/Makefile | 2 +-
> drivers/mmc/core/block.c | 7 +-
> drivers/mmc/core/bus.c | 5 +-
> drivers/mmc/core/core.c | 118 +-
> drivers/mmc/core/regulator.c | 14 +
> drivers/mmc/core/sd.c | 32 +
> drivers/mmc/core/sd_ops.c | 12 +
> drivers/mmc/core/uhs2.c | 883 +++++++++++++++
> drivers/mmc/core/uhs2.h | 21 +
> drivers/mmc/host/Kconfig | 10 +
> drivers/mmc/host/Makefile | 1 +
> drivers/mmc/host/sdhci-pci-core.c | 16 +-
> drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
> drivers/mmc/host/sdhci-pci.h | 3 +
> drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci-uhs2.h | 224 ++++
> drivers/mmc/host/sdhci.c | 333 +++---
> drivers/mmc/host/sdhci.h | 117 +-
> include/linux/mmc/card.h | 1 +
> include/linux/mmc/core.h | 6 +
> include/linux/mmc/host.h | 31 +
> include/linux/mmc/uhs2.h | 268 +++++
> 22 files changed, 3961 insertions(+), 158 deletions(-)
> create mode 100644 drivers/mmc/core/uhs2.c
> create mode 100644 drivers/mmc/core/uhs2.h
> create mode 100644 drivers/mmc/host/sdhci-uhs2.c
> create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> create mode 100644 include/linux/mmc/uhs2.h
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755
2021-08-02 16:22 ` Ulf Hansson
@ 2021-08-06 6:37 ` Lai Jason
2021-08-06 10:11 ` Ulf Hansson
0 siblings, 1 reply; 4+ messages in thread
From: Lai Jason @ 2021-08-06 6:37 UTC (permalink / raw)
To: Ulf Hansson
Cc: Adrian Hunter, linux-mmc, Linux Kernel Mailing List, Ben Chuang,
GregTu[杜啟軒],
AKASHI Takahiro, Jason Lai
On Tue, 03 Aug 2021 at 12:23, Ulf Hansson <ulf.hansson@linaro.org> wrote:
>
> On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@gmail.com> wrote:
> >
> > Summary
> > =======
> > In these patches we focus on uhs2 side to address Ulf's suggestion which
> > was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
> >
> >
> > I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> > Ulf's expection.
> >
> > Please review this series (particularly Patch 29/29).
>
> I think you have misunderstood the intent with the series that I
> posted [1] a while ago. The idea was to add the foundation of what
> should be needed in the mmc core to support UHS-II cards. Note, it's
> only the foundation, not the complete code.
>
> In other words, I think you should base the next version of $subject
> series *on top* of my series [1], rather than the opposite.
>
Actually, I understand your intention is to implement functions which
can be applied to control all UHS-II cards.
However, why do I choose to base it on “[RFC,v3.1,00/27] Add support
UHS-II for GL9755”?
Because it contains a complete UHS-II interface(both host & card side)
and UHS-II card can work normally.
The functionality of uhs2.c in the previous version of $subject almost
equal to sd_uhs2.c in your series [1].
The only difference is that UHS-II card initialization flow had been
modulated according to different phases(detect / phy_init /
legacy_init…).
Hence, I decided to apply your architecture of sd_uhs2.c to uhs2.c and
rename uhs2.c to sd_uhs2.c.
All patches are briefed below:
1. Patch #1 to patch #26 are used to create a UHS-II interface, both
in host side and sd card side.
- patch#1: add UHS-II support in public headers. (include/linux/mmc).
- patch#2: add UHS-II relative features in mmc_power_up() /
mmc_power_off() / mmc_regulator_get_supply().
- patch#3: skip set_chip_select().
- patch#4: flow of “interface selection and initialization” was a
bit modified for UHS-II card.
- patch#5: skip TMODE(field of UHS-II command packet) setup in some cases.
- patch#6 - #7: generate UHS-II SD command packet.
- patch#8: add a kernel configuration for enabling UHS-II support.
- patch#9: add UHS-II related definitions in sdhci.h and sdhci-uhs2.h.
- patch#10: add sdhci-uhs2.c as a module for UHS-II support.
- patch#11: dump UHS-II registers
- patch#12 - #26: add UHS-II host setting / control / attach,
card detect / attach.
2. Patch #27: drivers/mmc/host/sdhci-pci-gli.c contains
vendor(Genesyslogic) specific operations which are related to hardware
control.
3. Patch #28: remove redundant code.
4. Patch #29: move code from uhs2.c to sd_uhs2.c and place them to
proper functions.
> Moreover, next time, please try to better describe in each changelog
> and in a cover letter what you have changed and why, as it helps me to
> review.
Okay.
So what is the next you suggest to do after my explanation?
1. Update cover letter & change note in current version of $subject.
2. Submit a new version on top of your series [1].
For example: Series “Add Support UHS-II for GL9755“
patch #1~#4 are your original series[1] and patch #33 is to apply
your patch to support UHS-II cards. Below is the patch list:
[0/33] mmc: core: Add Support UHS-II for GL9755
[1/33] mmc: core: Cleanup printing of speed mode at card insertion
[2/33] mmc: core: Prepare to support SD UHS-II cards
[3/33] mmc: core: Announce successful insertion of an SD UHS-II card
[4/33] mmc: core: Extend support for mmc regulators with a vqmmc2
[5/33] mmc: add UHS-II related definitions in public headers
[6/33] mmc: core: UHS-II support, modify power-up sequence
……
[33/33] mmc: core: Apply Ulf's patch for supporting UHS-II car
Kind regards,
Jason Lai
> Kind regards
> Uffe
>
> [1]
> https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
>
> >
> > Thanks.
> > -Jason Lai
> >
> > ------ original cover letter from v3 ------
> > This is an interim snapshot of our next version, v4, for enabling
> > UHS-II on MMC/SD.
> >
> > It is focused on 'sdhci' side to address Adrian's comments regarding
> > "modularising" sdhci-uhs2.c.
> > The whole aim of this version is to get early feedback from Adrian (and
> > others) on this issue. Without any consensus about the code structure,
> > it would make little sense to go further ahead on sdhci side.
> > (Actually, Adrian has made no comments other than "modularising" so far.)
> >
> > I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> > set to meet what I believe Adrian expects; no UHS-II related code in
> > Legacy (UHS-I) code or sdhci.c.
> >
> > Nevertheless, almost of all changes I made are trivial and straightforward
> > in this direction, and I believe that there is no logic changed since v3
> > except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> > command sequences in addition to UHS-II errors. So I added extra handlings.
> >
> > I admit that there is plenty of room for improvements (for example,
> > handling host->flags), but again the focal point here is how sdhci-uhs2.c
> > should be built as a module.
> >
> > Please review this series (particularly Patch#8-#26 and #27) from this
> > viewpoint in the first place.
> > (Ben is working on 'host' side but there is no change on 'host' side
> > in this submission except a minor tweak.)
> >
> > Thanks,
> > -Takahiro Akashi
> >
> > ------ original cover letter from v3 ------
> > Summary
> > =======
> > These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
> >
> > About UHS-II, roughly deal with the following three parts:
> > 1) A UHS-II detection and initialization:
> > - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
> > [2]).
> > - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> > - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
> > 3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
> > Setup Sequence.
> >
> > 2) Send Legacy SD command through SD-TRAN
> > - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
> > compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
> > Types and Format Overview[3]).
> > - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
> > CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
> >
> > 3) UHS-II Interrupt
> > - Except for UHS-II error interrupts, most interrupts share the original
> > interrupt registers.
> >
> > Patch structure
> > ===============
> > patch#1-#7: for core
> > patch#8-#17: for sdhci
> > patch#18-#21: for GL9755
> >
> > Tests
> > =====
> > Ran 'dd' command to evaluate the performance:
> > (SanDisk UHS-II card on GL9755 controller)
> > Read Write
> > UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> > UHS-II enabled : 206MB/s 80MB/s
> >
> > TODO
> > ====
> > - replace some define with BIT macro
> >
> > Reference
> > =========
> > [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> > [2] SD Host Controller Simplified Specification 4.20
> > [3] UHS-II Simplified Addendum 1.02
> >
> > Changes in v3 (Jul. 10, 2020)
> > * rebased to v5.8-rc4
> > * add copyright notice
> > * reorganize the patch set and split some commits into smaller ones
> > * separate uhs-2 headers from others
> > * correct wrong spellings
> > * fix most of checkpatch warnings/errors
> > * remove all k[cz]alloc() from the code
> > * guard sdhci-uhs2 specific code with
> > 'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> > * make sdhci-uhs2.c as a module
> > * trivial changes, including
> > - rename back sdhci-core.c to sdhci.c
> > - allow vendor code to disable uhs2 if v4_mode == 0
> > in __sdhci_add_host()
> > - merge uhs2_power_up() into mmc_power_up()
> > - remove flag_uhs2 from mmc_attach_sd()
> > - add function descriptions to EXPORT'ed functions
> > - other minor code optimization
> >
> > Changes in v2 (Jan. 9, 2020)
> > * rebased to v5.5-rc5
> >
> > AKASHI Takahiro (23):
> > mmc: core: UHS-II support, modify power-up sequence
> > mmc: core: UHS-II support, skip set_chip_select()
> > mmc: core: UHS-II support, skip TMODE setup in some cases
> > mmc: core: UHS-II support, generate UHS-II SD command packet
> > mmc: core: UHS-II support, set APP_CMD bit if necessary
> > mmc: sdhci: add a kernel configuration for enabling UHS-II support
> > mmc: sdhci: add UHS-II related definitions in headers
> > mmc: sdhci: add UHS-II module
> > mmc: sdhci-uhs2: dump UHS-II registers
> > mmc: sdhci-uhs2: add reset function
> > mmc: sdhci-uhs2: add set_power() to support vdd2
> > mmc: sdhci-uhs2: skip signal_voltage_switch()
> > mmc: sdhci-uhs2: add set_timeout()
> > mmc: sdhci-uhs2: add set_ios()
> > mmc: sdhci-uhs2: add detect_init() to detect the interface
> > mmc: sdhci-uhs2: add clock operations
> > mmc: sdhci-uhs2: add set_reg() to initialise the interface
> > mmc: sdhci-uhs2: add request() and others
> > mmc: sdhci-uhs2: add irq() and others
> > mmc: sdhci-uhs2: add add_host() and others to set up the driver
> > mmc: core: add post-mmc_attach_sd hook
> > mmc: sdhci-pci: add UHS-II support framework
> > mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
> >
> > Ben Chuang (4):
> > mmc: add UHS-II related definitions in public headers
> > mmc: core: UHS-II support, try to select UHS-II interface
> > mmc: sdhci-uhs2: add pre-detect_init hook
> > mmc: sdhci-uhs2: add post-mmc_attach_sd hook
> >
> > drivers/mmc/core/Makefile | 2 +-
> > drivers/mmc/core/block.c | 7 +-
> > drivers/mmc/core/bus.c | 5 +-
> > drivers/mmc/core/core.c | 118 +-
> > drivers/mmc/core/regulator.c | 14 +
> > drivers/mmc/core/sd.c | 32 +
> > drivers/mmc/core/sd_ops.c | 12 +
> > drivers/mmc/core/uhs2.c | 883 +++++++++++++++
> > drivers/mmc/core/uhs2.h | 21 +
> > drivers/mmc/host/Kconfig | 10 +
> > drivers/mmc/host/Makefile | 1 +
> > drivers/mmc/host/sdhci-pci-core.c | 16 +-
> > drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
> > drivers/mmc/host/sdhci-pci.h | 3 +
> > drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci-uhs2.h | 224 ++++
> > drivers/mmc/host/sdhci.c | 333 +++---
> > drivers/mmc/host/sdhci.h | 117 +-
> > include/linux/mmc/card.h | 1 +
> > include/linux/mmc/core.h | 6 +
> > include/linux/mmc/host.h | 31 +
> > include/linux/mmc/uhs2.h | 268 +++++
> > 22 files changed, 3961 insertions(+), 158 deletions(-)
> > create mode 100644 drivers/mmc/core/uhs2.c
> > create mode 100644 drivers/mmc/core/uhs2.h
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.c
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> > create mode 100644 include/linux/mmc/uhs2.h
Ulf Hansson <ulf.hansson@linaro.org> 於 2021年8月3日 週二 上午12:23寫道：
>
> On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@gmail.com> wrote:
> >
> > Summary
> > =======
> > In these patches we focus on uhs2 side to address Ulf's suggestion which
> > was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
> >
> >
> > I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> > Ulf's expection.
> >
> > Please review this series (particularly Patch 29/29).
>
> I think you have misunderstood the intent with the series that I
> posted [1] a while ago. The idea was to add the foundation of what
> should be needed in the mmc core to support UHS-II cards. Note, it's
> only the foundation, not the complete code.
>
> In other words, I think you should base the next version of $subject
> series *on top* of my series [1], rather than the opposite.
>
> Moreover, next time, please try to better describe in each changelog
> and in a cover letter what you have changed and why, as it helps me to
> review.
>
> Kind regards
> Uffe
>
> [1]
> https://patchwork.kernel.org/project/linux-mmc/list/?series=438509
>
> >
> > Thanks.
> > -Jason Lai
> >
> > ------ original cover letter from v3 ------
> > This is an interim snapshot of our next version, v4, for enabling
> > UHS-II on MMC/SD.
> >
> > It is focused on 'sdhci' side to address Adrian's comments regarding
> > "modularising" sdhci-uhs2.c.
> > The whole aim of this version is to get early feedback from Adrian (and
> > others) on this issue. Without any consensus about the code structure,
> > it would make little sense to go further ahead on sdhci side.
> > (Actually, Adrian has made no comments other than "modularising" so far.)
> >
> > I heavily reworked/refactored sdhci-uhs2.c and re-organised the patch
> > set to meet what I believe Adrian expects; no UHS-II related code in
> > Legacy (UHS-I) code or sdhci.c.
> >
> > Nevertheless, almost of all changes I made are trivial and straightforward
> > in this direction, and I believe that there is no logic changed since v3
> > except sdhci_uhs2_irq(), as ops->irq hook, where we must deal with UHS-II
> > command sequences in addition to UHS-II errors. So I added extra handlings.
> >
> > I admit that there is plenty of room for improvements (for example,
> > handling host->flags), but again the focal point here is how sdhci-uhs2.c
> > should be built as a module.
> >
> > Please review this series (particularly Patch#8-#26 and #27) from this
> > viewpoint in the first place.
> > (Ben is working on 'host' side but there is no change on 'host' side
> > in this submission except a minor tweak.)
> >
> > Thanks,
> > -Takahiro Akashi
> >
> > ------ original cover letter from v3 ------
> > Summary
> > =======
> > These patches[1] support UHS-II and fix GL9755 UHS-II compatibility.
> >
> > About UHS-II, roughly deal with the following three parts:
> > 1) A UHS-II detection and initialization:
> > - Host setup to support UHS-II (Section 3.13.1 Host Controller Setup Sequence
> > [2]).
> > - Detect a UHS-II I/F (Section 3.13.2 Card Interface Detection Sequence[2]).
> > - In step(9) of Section 3.13.2 in [2], UHS-II initialization is include Section
> > 3.13.3 UHS-II Card Initialization and Section 3.13.4 UHS-II Setting Register
> > Setup Sequence.
> >
> > 2) Send Legacy SD command through SD-TRAN
> > - Encapsulated SD packets are defined in SD-TRAN in order to ensure Legacy SD
> > compatibility and preserve Legacy SD infrastructures (Section 7.1.1 Packet
> > Types and Format Overview[3]).
> > - Host issue a UHS-II CCMD packet or a UHS-II DCMD (Section 3.13.5 UHS-II
> > CCMD Packet issuing and Section 3.13.6 UHS-II DCMD Packet issuing[2]).
> >
> > 3) UHS-II Interrupt
> > - Except for UHS-II error interrupts, most interrupts share the original
> > interrupt registers.
> >
> > Patch structure
> > ===============
> > patch#1-#7: for core
> > patch#8-#17: for sdhci
> > patch#18-#21: for GL9755
> >
> > Tests
> > =====
> > Ran 'dd' command to evaluate the performance:
> > (SanDisk UHS-II card on GL9755 controller)
> > Read Write
> > UHS-II disabled (UHS-I): 88.3MB/s 60.7MB/s
> > UHS-II enabled : 206MB/s 80MB/s
> >
> > TODO
> > ====
> > - replace some define with BIT macro
> >
> > Reference
> > =========
> > [1] https://gitlab.com/ben.chuang/linux-uhs2-gl9755.git
> > [2] SD Host Controller Simplified Specification 4.20
> > [3] UHS-II Simplified Addendum 1.02
> >
> > Changes in v3 (Jul. 10, 2020)
> > * rebased to v5.8-rc4
> > * add copyright notice
> > * reorganize the patch set and split some commits into smaller ones
> > * separate uhs-2 headers from others
> > * correct wrong spellings
> > * fix most of checkpatch warnings/errors
> > * remove all k[cz]alloc() from the code
> > * guard sdhci-uhs2 specific code with
> > 'if (IS_ENABLED(CONFIG_MMC_SDHCI_UHS2))'
> > * make sdhci-uhs2.c as a module
> > * trivial changes, including
> > - rename back sdhci-core.c to sdhci.c
> > - allow vendor code to disable uhs2 if v4_mode == 0
> > in __sdhci_add_host()
> > - merge uhs2_power_up() into mmc_power_up()
> > - remove flag_uhs2 from mmc_attach_sd()
> > - add function descriptions to EXPORT'ed functions
> > - other minor code optimization
> >
> > Changes in v2 (Jan. 9, 2020)
> > * rebased to v5.5-rc5
> >
> > AKASHI Takahiro (23):
> > mmc: core: UHS-II support, modify power-up sequence
> > mmc: core: UHS-II support, skip set_chip_select()
> > mmc: core: UHS-II support, skip TMODE setup in some cases
> > mmc: core: UHS-II support, generate UHS-II SD command packet
> > mmc: core: UHS-II support, set APP_CMD bit if necessary
> > mmc: sdhci: add a kernel configuration for enabling UHS-II support
> > mmc: sdhci: add UHS-II related definitions in headers
> > mmc: sdhci: add UHS-II module
> > mmc: sdhci-uhs2: dump UHS-II registers
> > mmc: sdhci-uhs2: add reset function
> > mmc: sdhci-uhs2: add set_power() to support vdd2
> > mmc: sdhci-uhs2: skip signal_voltage_switch()
> > mmc: sdhci-uhs2: add set_timeout()
> > mmc: sdhci-uhs2: add set_ios()
> > mmc: sdhci-uhs2: add detect_init() to detect the interface
> > mmc: sdhci-uhs2: add clock operations
> > mmc: sdhci-uhs2: add set_reg() to initialise the interface
> > mmc: sdhci-uhs2: add request() and others
> > mmc: sdhci-uhs2: add irq() and others
> > mmc: sdhci-uhs2: add add_host() and others to set up the driver
> > mmc: core: add post-mmc_attach_sd hook
> > mmc: sdhci-pci: add UHS-II support framework
> > mmc: sdhci-pci-gli: enable UHS-II mode for GL9755
> >
> > Ben Chuang (4):
> > mmc: add UHS-II related definitions in public headers
> > mmc: core: UHS-II support, try to select UHS-II interface
> > mmc: sdhci-uhs2: add pre-detect_init hook
> > mmc: sdhci-uhs2: add post-mmc_attach_sd hook
> >
> > drivers/mmc/core/Makefile | 2 +-
> > drivers/mmc/core/block.c | 7 +-
> > drivers/mmc/core/bus.c | 5 +-
> > drivers/mmc/core/core.c | 118 +-
> > drivers/mmc/core/regulator.c | 14 +
> > drivers/mmc/core/sd.c | 32 +
> > drivers/mmc/core/sd_ops.c | 12 +
> > drivers/mmc/core/uhs2.c | 883 +++++++++++++++
> > drivers/mmc/core/uhs2.h | 21 +
> > drivers/mmc/host/Kconfig | 10 +
> > drivers/mmc/host/Makefile | 1 +
> > drivers/mmc/host/sdhci-pci-core.c | 16 +-
> > drivers/mmc/host/sdhci-pci-gli.c | 318 +++++-
> > drivers/mmc/host/sdhci-pci.h | 3 +
> > drivers/mmc/host/sdhci-uhs2.c | 1697 +++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci-uhs2.h | 224 ++++
> > drivers/mmc/host/sdhci.c | 333 +++---
> > drivers/mmc/host/sdhci.h | 117 +-
> > include/linux/mmc/card.h | 1 +
> > include/linux/mmc/core.h | 6 +
> > include/linux/mmc/host.h | 31 +
> > include/linux/mmc/uhs2.h | 268 +++++
> > 22 files changed, 3961 insertions(+), 158 deletions(-)
> > create mode 100644 drivers/mmc/core/uhs2.c
> > create mode 100644 drivers/mmc/core/uhs2.h
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.c
> > create mode 100644 drivers/mmc/host/sdhci-uhs2.h
> > create mode 100644 include/linux/mmc/uhs2.h
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755
2021-08-06 6:37 ` Lai Jason
@ 2021-08-06 10:11 ` Ulf Hansson
0 siblings, 0 replies; 4+ messages in thread
From: Ulf Hansson @ 2021-08-06 10:11 UTC (permalink / raw)
To: Lai Jason
Cc: Adrian Hunter, linux-mmc, Linux Kernel Mailing List, Ben Chuang,
GregTu[杜啟軒],
AKASHI Takahiro, Jason Lai
On Fri, 6 Aug 2021 at 08:37, Lai Jason <jasonlai.genesyslogic@gmail.com> wrote:
>
> On Tue, 03 Aug 2021 at 12:23, Ulf Hansson <ulf.hansson@linaro.org> wrote:
> >
> > On Thu, 22 Jul 2021 at 07:14, Jason Lai <jasonlai.genesyslogic@gmail.com> wrote:
> > >
> > > Summary
> > > =======
> > > In these patches we focus on uhs2 side to address Ulf's suggestion which
> > > was mentioned in patch [mmc: core: Preparations to support SD UHS-II cards].
> > >
> > >
> > > I moved codes in uhs2.c to proper functions in sd_uhs2.c, which should meet
> > > Ulf's expection.
> > >
> > > Please review this series (particularly Patch 29/29).
> >
> > I think you have misunderstood the intent with the series that I
> > posted [1] a while ago. The idea was to add the foundation of what
> > should be needed in the mmc core to support UHS-II cards. Note, it's
> > only the foundation, not the complete code.
> >
> > In other words, I think you should base the next version of $subject
> > series *on top* of my series [1], rather than the opposite.
> >
> Actually, I understand your intention is to implement functions which
> can be applied to control all UHS-II cards.
> However, why do I choose to base it on “[RFC,v3.1,00/27] Add support
> UHS-II for GL9755”?
> Because it contains a complete UHS-II interface(both host & card side)
> and UHS-II card can work normally.
It doesn't matter if things "work".
The code/patches need to be better organized than currently,
especially the changes for the mmc core, which is why I stepped in and
tried to help out earlier. Otherwise it is impossible for me to review
the changes, but also to maintain the code in the long run.
The sdhci part is likely a bit more mature as it has been reviewed and
iterated with Adrian/Ben/Akashi-san. However, new/more changes needed
when my suggested changes for the mmc core come into play.
[...]
Kind regards
Uffe
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2021-08-06 10:13 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-22 5:14 [RFC PATCH v3.2 00/29] Add support UHS-II for GL9755 Jason Lai
2021-08-02 16:22 ` Ulf Hansson
2021-08-06 6:37 ` Lai Jason
2021-08-06 10:11 ` Ulf Hansson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).