From: "Z.q. Hou" <zhiqiang.hou@nxp.com>
To: Shawn Guo <shawnguo@kernel.org>
Cc: "devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
"robh+dt@kernel.org" <robh+dt@kernel.org>,
"michael@walle.cc" <michael@walle.cc>,
Leo Li <leoyang.li@nxp.com>, Mingkai Hu <mingkai.hu@nxp.com>,
"M.h. Lian" <minghuan.lian@nxp.com>,
Xiaowei Bao <xiaowei.bao@nxp.com>
Subject: RE: [PATCHv7] arm64: dts: ls1028a: Add PCIe controller DT nodes
Date: Wed, 11 Mar 2020 09:50:29 +0000 [thread overview]
Message-ID: <DB8PR04MB674761BF8BA68ACA26497B4784FC0@DB8PR04MB6747.eurprd04.prod.outlook.com> (raw)
In-Reply-To: <20200311082117.GA29269@dragon>
Hi Shawn,
Thanks a lot for your comments!
> -----Original Message-----
> From: Shawn Guo <shawnguo@kernel.org>
> Sent: 2020年3月11日 16:21
> To: Z.q. Hou <zhiqiang.hou@nxp.com>
> Cc: devicetree@vger.kernel.org; linux-kernel@vger.kernel.org;
> robh+dt@kernel.org; michael@walle.cc; Leo Li <leoyang.li@nxp.com>;
> Mingkai Hu <mingkai.hu@nxp.com>; M.h. Lian <minghuan.lian@nxp.com>;
> Xiaowei Bao <xiaowei.bao@nxp.com>
> Subject: Re: [PATCHv7] arm64: dts: ls1028a: Add PCIe controller DT nodes
>
> On Mon, Mar 02, 2020 at 12:23:05PM +0800, Zhiqiang Hou wrote:
> > From: Xiaowei Bao <xiaowei.bao@nxp.com>
> >
> > LS1028a implements 2 PCIe 3.0 controllers.
> >
> > Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
> > Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
> > Tested-by: Michael Walle <michael@walle.cc>
> > ---
> > V7:
> > - Rebased the patch to the latest code base.
> > - Added property 'iommu-map'.
> >
> > .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 54
> +++++++++++++++++++
> > 1 file changed, 54 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> > index 41c9633293fb..3f31641dcced 100644
> > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> > @@ -717,6 +717,60 @@
> > #thermal-sensor-cells = <1>;
> > };
> >
> > + pcie@3400000 {
>
> Please keep nodes sorted in unit-address.
OK, will correct in next version.
Thanks,
Zhiqiang
>
> Shawn
>
> > + compatible = "fsl,ls1028a-pcie";
> > + reg = <0x00 0x03400000 0x0 0x00100000 /* controller
> registers */
> > + 0x80 0x00000000 0x0 0x00002000>; /* configuration
> space */
> > + reg-names = "regs", "config";
> > + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, /* PME
> interrupt */
> > + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; /* aer
> interrupt */
> > + interrupt-names = "pme", "aer";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + device_type = "pci";
> > + dma-coherent;
> > + num-viewport = <8>;
> > + bus-range = <0x0 0xff>;
> > + ranges = <0x81000000 0x0 0x00000000 0x80 0x00010000 0x0
> 0x00010000 /* downstream I/O */
> > + 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0
> 0x40000000>; /* non-prefetchable memory */
> > + msi-parent = <&its>;
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 7>;
> > + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 109
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 2 &gic 0 0 GIC_SPI 110
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 3 &gic 0 0 GIC_SPI 111
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 4 &gic 0 0 GIC_SPI 112
> IRQ_TYPE_LEVEL_HIGH>;
> > + iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
> > + status = "disabled";
> > + };
> > +
> > + pcie@3500000 {
> > + compatible = "fsl,ls1028a-pcie";
> > + reg = <0x00 0x03500000 0x0 0x00100000 /* controller
> registers */
> > + 0x88 0x00000000 0x0 0x00002000>; /* configuration
> space */
> > + reg-names = "regs", "config";
> > + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
> > + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "pme", "aer";
> > + #address-cells = <3>;
> > + #size-cells = <2>;
> > + device_type = "pci";
> > + dma-coherent;
> > + num-viewport = <8>;
> > + bus-range = <0x0 0xff>;
> > + ranges = <0x81000000 0x0 0x00000000 0x88 0x00010000 0x0
> 0x00010000 /* downstream I/O */
> > + 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0
> 0x40000000>; /* non-prefetchable memory */
> > + msi-parent = <&its>;
> > + #interrupt-cells = <1>;
> > + interrupt-map-mask = <0 0 0 7>;
> > + interrupt-map = <0000 0 0 1 &gic 0 0 GIC_SPI 114
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 2 &gic 0 0 GIC_SPI 115
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 3 &gic 0 0 GIC_SPI 116
> IRQ_TYPE_LEVEL_HIGH>,
> > + <0000 0 0 4 &gic 0 0 GIC_SPI 117
> IRQ_TYPE_LEVEL_HIGH>;
> > + iommu-map = <0 &smmu 0 1>; /* Fixed-up by bootloader */
> > + status = "disabled";
> > + };
> > +
> > pcie@1f0000000 { /* Integrated Endpoint Root Complex */
> > compatible = "pci-host-ecam-generic";
> > reg = <0x01 0xf0000000 0x0 0x100000>;
> > --
> > 2.17.1
> >
prev parent reply other threads:[~2020-03-11 9:50 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-02 4:23 [PATCHv7] arm64: dts: ls1028a: Add PCIe controller DT nodes Zhiqiang Hou
2020-03-11 8:21 ` Shawn Guo
2020-03-11 9:50 ` Z.q. Hou [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=DB8PR04MB674761BF8BA68ACA26497B4784FC0@DB8PR04MB6747.eurprd04.prod.outlook.com \
--to=zhiqiang.hou@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=michael@walle.cc \
--cc=minghuan.lian@nxp.com \
--cc=mingkai.hu@nxp.com \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
--cc=xiaowei.bao@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).