From: Andy Tang <andy.tang@nxp.com>
To: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>, Leo Li <leoyang.li@nxp.com>,
Rob Herring <robh+dt@kernel.org>,
lakml <linux-arm-kernel@lists.infradead.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>, LKML <linux-kernel@vger.kernel.org>
Subject: RE: [EXT] Re: [PATCH 1/2] arm64: dts: ls1088a: add more thermal zone support
Date: Tue, 30 Jun 2020 05:28:16 +0000 [thread overview]
Message-ID: <DBBPR04MB609085CD69E4CCBDD49CCF66F36F0@DBBPR04MB6090.eurprd04.prod.outlook.com> (raw)
In-Reply-To: <CAHLCerO3B4Z67KP8VaF957Jkid21gLvzhS49gNeqUC+6muPkjA@mail.gmail.com>
> -----Original Message-----
> From: Amit Kucheria <amit.kucheria@linaro.org>
> Sent: 2020年6月30日 13:12
> To: Andy Tang <andy.tang@nxp.com>
> Cc: Shawn Guo <shawnguo@kernel.org>; Leo Li <leoyang.li@nxp.com>; Rob
> Herring <robh+dt@kernel.org>; lakml <linux-arm-kernel@lists.infradead.org>;
> open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS
> <devicetree@vger.kernel.org>; LKML <linux-kernel@vger.kernel.org>
> Subject: [EXT] Re: [PATCH 1/2] arm64: dts: ls1088a: add more thermal zone
> support
>
> Caution: EXT Email
>
> On Tue, Jun 30, 2020 at 8:56 AM <andy.tang@nxp.com> wrote:
> >
> > From: Yuantian Tang <andy.tang@nxp.com>
> >
> > There are 2 thermal zones in ls1088a soc. Add the other thermal zone
> > node to enable it.
> > Also update the values in calibration table to make the temperatures
> > monitored more precise.
> >
> > Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
> > ---
> > .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 100
> > +++++++++++-------
> > 1 file changed, 62 insertions(+), 38 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> > b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> > index 36a799554620..ccbbc23e6c85 100644
> > --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
> > @@ -129,19 +129,19 @@
> > };
> >
> > thermal-zones {
> > - cpu_thermal: cpu-thermal {
> > + core-cluster {
> > polling-delay-passive = <1000>;
> > polling-delay = <5000>;
> > thermal-sensors = <&tmu 0>;
> >
> > trips {
> > - cpu_alert: cpu-alert {
> > + core_cluster_alert:
> core-cluster-alert
> > + {
> > temperature = <85000>;
> > hysteresis = <2000>;
> > type = "passive";
> > };
> >
> > - cpu_crit: cpu-crit {
> > + core_cluster_crit: core-cluster-crit {
> > temperature = <95000>;
> > hysteresis = <2000>;
> > type = "critical"; @@
> -150,7
> > +150,7 @@
> >
> > cooling-maps {
> > map0 {
> > - trip = <&cpu_alert>;
> > + trip =
> <&core_cluster_alert>;
> > cooling-device =
> > <&cpu0
> THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > <&cpu1
> > THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, @@ -163,6 +163,26 @@
> > };
> > };
> > };
> > +
> > + soc {
> > + polling-delay-passive = <1000>;
> > + polling-delay = <5000>;
> > + thermal-sensors = <&tmu 1>;
> > +
> > + trips {
> > + soc-alert {
> > + temperature = <85000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > +
> > + soc-crit {
> > + temperature = <95000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + };
>
> You should also add a cooling-maps section for this thermal zone given that it
> has a passive trip type. Otherwise there is no use for a passive trip type.
It is better to have a cooling device. But there is only one cooling device on this platform
which is used by core-cluster. So there is no extra cooling device for it.
This zone can take action when critical temp is reached. So it is still useful.
What do you suggest?
BR,
Andy
>
> > };
> >
> > timer {
> > @@ -209,45 +229,49 @@
> > compatible = "fsl,qoriq-tmu";
> > reg = <0x0 0x1f80000 0x0 0x10000>;
> > interrupts = <0 23 0x4>;
> > - fsl,tmu-range = <0xb0000 0x9002a 0x6004c
> 0x30062>;
> > + fsl,tmu-range = <0xb0000 0x9002a 0x6004c
> > + 0x70062>;
> > fsl,tmu-calibration =
> > /* Calibration data group 1 */
> > - <0x00000000 0x00000026
> > - 0x00000001 0x0000002d
> > - 0x00000002 0x00000032
> > - 0x00000003 0x00000039
> > - 0x00000004 0x0000003f
> > - 0x00000005 0x00000046
> > - 0x00000006 0x0000004d
> > - 0x00000007 0x00000054
> > - 0x00000008 0x0000005a
> > - 0x00000009 0x00000061
> > - 0x0000000a 0x0000006a
> > - 0x0000000b 0x00000071
> > + <0x00000000 0x00000023
> > + 0x00000001 0x0000002a
> > + 0x00000002 0x00000030
> > + 0x00000003 0x00000037
> > + 0x00000004 0x0000003d
> > + 0x00000005 0x00000044
> > + 0x00000006 0x0000004a
> > + 0x00000007 0x00000051
> > + 0x00000008 0x00000057
> > + 0x00000009 0x0000005e
> > + 0x0000000a 0x00000064
> > + 0x0000000b 0x0000006b
> > /* Calibration data group 2 */
> > - 0x00010000 0x00000025
> > - 0x00010001 0x0000002c
> > - 0x00010002 0x00000035
> > - 0x00010003 0x0000003d
> > - 0x00010004 0x00000045
> > - 0x00010005 0x0000004e
> > - 0x00010006 0x00000057
> > - 0x00010007 0x00000061
> > - 0x00010008 0x0000006b
> > - 0x00010009 0x00000076
> > + 0x00010000 0x00000022
> > + 0x00010001 0x0000002a
> > + 0x00010002 0x00000032
> > + 0x00010003 0x0000003a
> > + 0x00010004 0x00000042
> > + 0x00010005 0x0000004a
> > + 0x00010006 0x00000052
> > + 0x00010007 0x0000005a
> > + 0x00010008 0x00000062
> > + 0x00010009 0x0000006a
> > /* Calibration data group 3 */
> > - 0x00020000 0x00000029
> > - 0x00020001 0x00000033
> > - 0x00020002 0x0000003d
> > - 0x00020003 0x00000049
> > - 0x00020004 0x00000056
> > - 0x00020005 0x00000061
> > - 0x00020006 0x0000006d
> > + 0x00020000 0x00000021
> > + 0x00020001 0x0000002b
> > + 0x00020002 0x00000035
> > + 0x00020003 0x00000040
> > + 0x00020004 0x0000004a
> > + 0x00020005 0x00000054
> > + 0x00020006 0x0000005e
> > /* Calibration data group 4 */
> > - 0x00030000 0x00000021
> > - 0x00030001 0x0000002a
> > - 0x00030002 0x0000003c
> > - 0x00030003 0x0000004e>;
> > + 0x00030000 0x00000010
> > + 0x00030001 0x0000001c
> > + 0x00030002 0x00000027
> > + 0x00030003 0x00000032
> > + 0x00030004 0x0000003e
> > + 0x00030005 0x00000049
> > + 0x00030006 0x00000054
> > + 0x00030007 0x00000060>;
> > little-endian;
> > #thermal-sensor-cells = <1>;
> > };
> > --
> > 2.17.1
> >
next prev parent reply other threads:[~2020-06-30 5:28 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-06-30 3:20 [PATCH 1/2] arm64: dts: ls1088a: add more thermal zone support andy.tang
2020-06-30 3:20 ` [PATCH 2/2] arm64: dts: ls208xa: " andy.tang
2020-06-30 5:12 ` [PATCH 1/2] arm64: dts: ls1088a: " Amit Kucheria
2020-06-30 5:28 ` Andy Tang [this message]
2020-06-30 5:36 ` [EXT] " Amit Kucheria
2020-06-30 6:37 ` Andy Tang
2020-06-30 6:46 ` Amit Kucheria
2020-06-30 7:27 ` Andy Tang
2020-07-02 3:33 ` Andy Tang
2020-07-13 3:15 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=DBBPR04MB609085CD69E4CCBDD49CCF66F36F0@DBBPR04MB6090.eurprd04.prod.outlook.com \
--to=andy.tang@nxp.com \
--cc=amit.kucheria@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).