From: Peter <cogwepeter@cogweb.net>
To: linux-kernel@vger.kernel.org
Subject: Linux v2.6.0-test1
Date: Mon, 14 Jul 2003 00:26:02 -0700 (PDT) [thread overview]
Message-ID: <Pine.LNX.4.44.0307140015390.9819-100000@greenie.frogspace.net> (raw)
In-Reply-To: <Pine.LNX.4.44.0305221240040.15298-100000@greenie.frogspace.net>
The kernel compiled with no errors. On booting, I got this:
ACPI: Subsystem revision 20030619
ACPI breakpoint: Executed AML Breakpoint opcode
If I just wanted to boot, which option should I disable?
This is a vpr matrix 200a5 laptop with an ALi M1671 chipset and various
ACPI options enabled, including CONFIG_X86_P4_CLOCKMOD=m. Details below.
2.5.69 has been running fine for a long time now, but there are some new
ACPI options.
Cheers,
Peter
System:
00:00.0 Host bridge: ALi Corporation M1671 Super P4 Northbridge [AGP4X,PCI and SDR/DDR] (rev 02)
00:01.0 PCI bridge: ALi Corporation PCI to AGP Controller
00:06.0 Multimedia audio controller: ALi Corporation M5451 PCI AC-Link Controller Audio Device (rev 02)
00:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
00:09.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01)
00:0a.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
00:0b.0 USB Controller: VIA Technologies, Inc. USB (rev 50)
00:0b.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51)
00:0c.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c4)
00:11.0 Bridge: ALi Corporation M7101 PMU
00:12.0 Ethernet controller: National Semiconductor Corporation DP83815 (MacPhyter) Ethernet Controller
01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 420 Go 32M] (rev a3)
Configuration:
#
# Power management options (ACPI, APM)
#
CONFIG_PM=y
CONFIG_SOFTWARE_SUSPEND=y
#
# ACPI Support
#
CONFIG_ACPI=y
# CONFIG_ACPI_HT_ONLY is not set
CONFIG_ACPI_BOOT=y
CONFIG_ACPI_SLEEP=y
CONFIG_ACPI_SLEEP_PROC_FS=y
CONFIG_ACPI_AC=y
CONFIG_ACPI_BATTERY=y
CONFIG_ACPI_BUTTON=y
CONFIG_ACPI_FAN=y
CONFIG_ACPI_PROCESSOR=y
CONFIG_ACPI_THERMAL=y
# CONFIG_ACPI_ASUS is not set
# CONFIG_ACPI_TOSHIBA is not set
# CONFIG_ACPI_DEBUG is not set
CONFIG_ACPI_BUS=y
CONFIG_ACPI_INTERPRETER=y
CONFIG_ACPI_EC=y
CONFIG_ACPI_POWER=y
CONFIG_ACPI_PCI=y
CONFIG_ACPI_SYSTEM=y
# CONFIG_APM is not set
#
# CPU Frequency scaling
#
CONFIG_CPU_FREQ=y
# CONFIG_CPU_FREQ_PROC_INTF is not set
CONFIG_CPU_FREQ_GOV_USERSPACE=y
# CONFIG_CPU_FREQ_24_API is not set
CONFIG_CPU_FREQ_TABLE=y
#
# CPUFreq processor drivers
#
# CONFIG_X86_ACPI_CPUFREQ is not set
# CONFIG_X86_POWERNOW_K6 is not set
# CONFIG_X86_POWERNOW_K7 is not set
# CONFIG_X86_GX_SUSPMOD is not set
# CONFIG_X86_SPEEDSTEP_ICH is not set
# CONFIG_X86_SPEEDSTEP_CENTRINO is not set
CONFIG_X86_P4_CLOCKMOD=m
# CONFIG_X86_LONGRUN is not set
# CONFIG_X86_LONGHAUL is not set
next prev parent reply other threads:[~2003-07-14 7:11 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-05-22 20:12 DMA gone on ALI 1533 Peter
2003-05-22 20:36 ` Bartlomiej Zolnierkiewicz
2003-07-14 7:26 ` Peter [this message]
2003-07-14 17:59 ` Trying to get DMA working with IDE alim15x3 controller Peter
2003-07-14 3:59 Linux v2.6.0-test1 Linus Torvalds
2003-07-15 4:11 ` Matt Reppert
2003-07-15 10:56 ` Dave Jones
2003-07-15 17:38 ` Dominik Brodowski
2003-07-15 18:11 ` Dave Jones
2003-07-14 11:01 John Bradford
2003-07-14 11:15 ` Alan Cox
2003-07-14 11:39 John Bradford
2003-07-14 11:33 ` Alan Cox
2003-07-14 13:56 ` Marcelo Tosatti
2003-07-14 15:07 ` Alan Cox
2003-07-14 16:44 ` Marcelo Tosatti
2003-07-14 11:50 John Bradford
2003-07-14 11:53 ` Dave Jones
2003-07-14 12:00 ` William Lee Irwin III
2003-07-14 12:39 ` Alan Cox
2003-07-14 12:47 ` William Lee Irwin III
2003-07-14 12:47 ` Alan Cox
2003-07-14 12:40 ` Alan Cox
2003-07-14 16:55 ` Kurt Wall
2003-07-15 7:52 Dirk Meul
2003-07-16 6:32 ` Martin Schlemmer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.LNX.4.44.0307140015390.9819-100000@greenie.frogspace.net \
--to=cogwepeter@cogweb.net \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).