* [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
@ 2021-07-28 17:43 chevron
2021-08-20 18:20 ` Bjorn Andersson
0 siblings, 1 reply; 5+ messages in thread
From: chevron @ 2021-07-28 17:43 UTC (permalink / raw)
To: agross, bjorn.andersson, linux-arm-msm, linux-kernel
Cc: shaper.liu, chevron.li, xiaoguang.yu, shirley.her
Improve the signal integrity for long SD bus trace by using 845+BH201 SD host redriver chip
Signed-off-by: chevron.li <chevron.li@bayhubtech.com>
---
change in V1:
1. copy Qualcomm driver base from sdhci-msm.c to sdhci-bayhub.c
2. implement the BH201 chip initialization function at sdhci-bayhub.c
3. implement the BH201 chip power control function at sdhci-bayhub.c
4. implement the BH201 chip tuning function at sdhci-bayhub.c
5. re-implement mmc_rescan to match BH201 mode switch flow at sdhci-bayhub.c
---
---
.../devicetree/bindings/mmc/sdhci-msm.txt | 1 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-bayhub.c | 6563 +++++++++++++++++
3 files changed, 6565 insertions(+)
create mode 100644 drivers/mmc/host/sdhci-bayhub.c
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index 4c7fa6a4ed15..a0401dc16929 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -20,6 +20,7 @@ Required properties:
"qcom,qcs404-sdhci", "qcom,sdhci-msm-v5"
"qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
"qcom,sdm845-sdhci", "qcom,sdhci-msm-v5"
+ "qcom,sdm845-bayhub-sdhci", "qcom,sdhci-msm-bayhub-v5"
"qcom,sdx55-sdhci", "qcom,sdhci-msm-v5";
"qcom,sm8250-sdhci", "qcom,sdhci-msm-v5"
NOTE that some old device tree files may be floating around that only
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 14004cc09aaa..d4d6f4cca732 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_MMC_SDHCI_OF_SPARX5) += sdhci-of-sparx5.o
obj-$(CONFIG_MMC_SDHCI_BCM_KONA) += sdhci-bcm-kona.o
obj-$(CONFIG_MMC_SDHCI_IPROC) += sdhci-iproc.o
obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-msm.o
+obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-bayhub.o
obj-$(CONFIG_MMC_SDHCI_ST) += sdhci-st.o
obj-$(CONFIG_MMC_SDHCI_MICROCHIP_PIC32) += sdhci-pic32.o
obj-$(CONFIG_MMC_SDHCI_BRCMSTB) += sdhci-brcmstb.o
diff --git a/drivers/mmc/host/sdhci-bayhub.c b/drivers/mmc/host/sdhci-bayhub.c
new file mode 100644
index 000000000000..75029470bd22
--- /dev/null
+++ b/drivers/mmc/host/sdhci-bayhub.c
@@ -0,0 +1,6563 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Bayhub Technologies, Inc. BH201 SDHCI bridge IC for
+ * VENDOR SDHCI platform driver source file
+ *
+ * Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/delay.h>
+#include <linux/mmc/mmc.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/iopoll.h>
+#include <linux/regulator/consumer.h>
+#include <linux/interconnect.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sd.h>
+#include <linux/io.h>
+#include <linux/of_gpio.h>
+
+#include "sdhci-pltfm.h"
+#include "cqhci.h"
+#include "../core/core.h"
+#include "../core/sd_ops.h"
+#include "../core/sdio_ops.h"
+#include "../core/mmc_ops.h"
+#include "../core/sd.h"
+#include "../core/bus.h"
+#include "../core/host.h"
+#include "../core/card.h"
+#include "../core/pwrseq.h"
+
+#define TRUE 1
+#define FALSE 0
+
+#define SD_FNC_AM_SDR50 0x2
+#define SD_FNC_AM_SDR104 0x3
+#define BIT_PASS_MASK (0x7ff)
+#define SDR104_MANUAL_INJECT 0x3ff
+#define SDR50_MANUAL_INJECT 0x77f
+
+#define TRUNING_RING_IDX(x) ((x) % TUNING_PHASE_SIZE)
+#define GET_IDX_VALUE(tb, x) (tb & (1 << (x)))
+#define GENERATE_IDX_VALUE(x) (1 << (x))
+#define GET_TRUNING_RING_IDX_VALUE(tb, x) \
+ (tb & (1 << TRUNING_RING_IDX(x)))
+#define GENERATE_TRUNING_RING_IDX_VALUE(x) \
+ (1 << TRUNING_RING_IDX(x))
+#define MAX_CFG_BIT_VAL (383)
+
+#define CORE_MCI_VERSION 0x50
+#define CORE_VERSION_MAJOR_SHIFT 28
+#define CORE_VERSION_MAJOR_MASK (0xf << CORE_VERSION_MAJOR_SHIFT)
+#define CORE_VERSION_MINOR_MASK 0xff
+
+#define CORE_MCI_GENERICS 0x70
+#define SWITCHABLE_SIGNALING_VOLTAGE BIT(29)
+
+#define HC_MODE_EN 0x1
+#define CORE_POWER 0x0
+#define CORE_SW_RST BIT(7)
+#define FF_CLK_SW_RST_DIS BIT(13)
+
+#define CORE_PWRCTL_BUS_OFF BIT(0)
+#define CORE_PWRCTL_BUS_ON BIT(1)
+#define CORE_PWRCTL_IO_LOW BIT(2)
+#define CORE_PWRCTL_IO_HIGH BIT(3)
+#define CORE_PWRCTL_BUS_SUCCESS BIT(0)
+#define CORE_PWRCTL_BUS_FAIL BIT(1)
+#define CORE_PWRCTL_IO_SUCCESS BIT(2)
+#define CORE_PWRCTL_IO_FAIL BIT(3)
+#define REQ_BUS_OFF BIT(0)
+#define REQ_BUS_ON BIT(1)
+#define REQ_IO_LOW BIT(2)
+#define REQ_IO_HIGH BIT(3)
+#define INT_MASK 0xf
+#define MAX_PHASES 16
+#define CORE_DLL_LOCK BIT(7)
+#define CORE_DDR_DLL_LOCK BIT(11)
+#define CORE_DLL_EN BIT(16)
+#define CORE_CDR_EN BIT(17)
+#define CORE_CK_OUT_EN BIT(18)
+#define CORE_CDR_EXT_EN BIT(19)
+#define CORE_DLL_PDN BIT(29)
+#define CORE_DLL_RST BIT(30)
+#define CORE_CMD_DAT_TRACK_SEL BIT(0)
+
+#define CORE_DDR_CAL_EN BIT(0)
+#define CORE_FLL_CYCLE_CNT BIT(18)
+#define CORE_DLL_CLOCK_DISABLE BIT(21)
+
+#define DLL_USR_CTL_POR_VAL 0x10800
+#define ENABLE_DLL_LOCK_STATUS BIT(26)
+#define FINE_TUNE_MODE_EN BIT(27)
+#define BIAS_OK_SIGNAL BIT(29)
+
+#define DLL_CONFIG_3_LOW_FREQ_VAL 0x08
+#define DLL_CONFIG_3_HIGH_FREQ_VAL 0x10
+
+#define CORE_VENDOR_SPEC_POR_VAL 0xa9c
+#define CORE_CLK_PWRSAVE BIT(1)
+#define CORE_HC_MCLK_SEL_DFLT (2 << 8)
+#define CORE_HC_MCLK_SEL_HS400 (3 << 8)
+#define CORE_HC_MCLK_SEL_MASK (3 << 8)
+#define CORE_IO_PAD_PWR_SWITCH_EN BIT(15)
+#define CORE_IO_PAD_PWR_SWITCH BIT(16)
+#define CORE_HC_SELECT_IN_EN BIT(18)
+#define CORE_HC_SELECT_IN_HS400 (6 << 19)
+#define CORE_HC_SELECT_IN_MASK (7 << 19)
+
+#define CORE_3_0V_SUPPORT BIT(25)
+#define CORE_1_8V_SUPPORT BIT(26)
+#define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT)
+
+#define CORE_CSR_CDC_CTLR_CFG0 0x130
+#define CORE_SW_TRIG_FULL_CALIB BIT(16)
+#define CORE_HW_AUTOCAL_ENA BIT(17)
+
+#define CORE_CSR_CDC_CTLR_CFG1 0x134
+#define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138
+#define CORE_TIMER_ENA BIT(16)
+
+#define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C
+#define CORE_CSR_CDC_REFCOUNT_CFG 0x140
+#define CORE_CSR_CDC_COARSE_CAL_CFG 0x144
+#define CORE_CDC_OFFSET_CFG 0x14C
+#define CORE_CSR_CDC_DELAY_CFG 0x150
+#define CORE_CDC_SLAVE_DDA_CFG 0x160
+#define CORE_CSR_CDC_STATUS0 0x164
+#define CORE_CALIBRATION_DONE BIT(0)
+
+#define CORE_CDC_ERROR_CODE_MASK 0x7000000
+
+#define CORE_CSR_CDC_GEN_CFG 0x178
+#define CORE_CDC_SWITCH_BYPASS_OFF BIT(0)
+#define CORE_CDC_SWITCH_RC_EN BIT(1)
+
+#define CORE_CDC_T4_DLY_SEL BIT(0)
+#define CORE_CMDIN_RCLK_EN BIT(1)
+#define CORE_START_CDC_TRAFFIC BIT(6)
+
+#define CORE_PWRSAVE_DLL BIT(3)
+
+#define DDR_CONFIG_POR_VAL 0x80040873
+
+
+#define INVALID_TUNING_PHASE -1
+#define SDHCI_MSM_MIN_CLOCK 400000
+#define CORE_FREQ_100MHZ (100 * 1000 * 1000)
+
+#define CDR_SELEXT_SHIFT 20
+#define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT)
+#define CMUX_SHIFT_PHASE_SHIFT 24
+#define CMUX_SHIFT_PHASE_MASK (7 << CMUX_SHIFT_PHASE_SHIFT)
+
+#define MSM_MMC_AUTOSUSPEND_DELAY_MS 50
+
+/* Timeout value to avoid infinite waiting for pwr_irq */
+#define MSM_PWR_IRQ_TIMEOUT_MS 5000
+
+/* Max load for eMMC Vdd-io supply */
+#define MMC_VQMMC_MAX_LOAD_UA 325000
+
+#define msm_bayhub_host_readl(msm_bayhub_host, host, offset) \
+ msm_bayhub_host->var_ops->msm_bayhub_readl_relaxed(host, offset)
+
+#define msm_bayhub_host_writel(msm_bayhub_host, val, host, offset) \
+ msm_bayhub_host->var_ops->msm_bayhub_writel_relaxed(val, host, offset)
+
+/* CQHCI vendor specific registers */
+#define CQHCI_VENDOR_CFG1 0xA00
+#define CQHCI_VENDOR_DIS_RST_ON_CQ_EN (0x3 << 13)
+
+#define TUNING_PHASE_SIZE 11
+#define GGC_CFG_DATA {0x07000000, 0x07364022, 0x01015412, 0x01062400,\
+ 0x10400076, 0x00025432, 0x01046076, 0x62011000,\
+ 0x30503106, 0x64141711, 0x10057513, 0x00336200,\
+ 0x00020006, 0x40000400, 0x12200310, 0x3A314177}
+
+struct ggc_bus_mode_cfg_t {
+ u32 tx_selb_tb[TUNING_PHASE_SIZE];
+ u32 all_selb_tb[TUNING_PHASE_SIZE];
+ u32 tx_selb_failed_history;
+ int bus_mode;
+ int default_sela;
+ int default_selb;
+ u32 default_delaycode;
+ u32 dll_voltage_unlock_cnt[4];
+ u32 max_delaycode;
+ u32 min_delaycode;
+ u32 delaycode_narrowdown_index;
+ u32 fail_phase;
+};
+
+enum tuning_stat_et {
+ NO_TUNING = 0,
+ OUTPUT_PASS_TYPE = 1,
+ SET_PHASE_FAIL_TYPE = 2,
+ TUNING_FAIL_TYPE = 3,
+ READ_STATUS_FAIL_TYPE = 4,
+ TUNING_CMD7_TIMEOUT = 5,
+ RETUNING_CASE = 6,
+};
+
+
+struct t_gg_reg_strt {
+ u32 ofs;
+ u32 mask;
+ u32 value;
+};
+
+struct rl_bit_lct {
+ u8 bits;
+ u8 rl_bits;
+};
+
+struct chk_type_t {
+ u8 right_valid:1;
+ u8 first_valid:1;
+ u8 record_valid:1;
+ u8 reserved:5;
+};
+
+static const char *const op_dbg_str[] = {
+ "no tuning",
+ "pass",
+ "set_phase_fail",
+ "tuning fail",
+ "read status fail",
+ "tuning CMD7 timeout",
+ "retuning case"
+};
+
+struct ggc_platform_t {
+ struct ggc_bus_mode_cfg_t sdr50;
+ struct ggc_bus_mode_cfg_t sdr104;
+ struct ggc_bus_mode_cfg_t *cur_bus_mode;
+
+ struct t_gg_reg_strt pha_stas_rx_low32;
+ struct t_gg_reg_strt pha_stas_rx_high32;
+ struct t_gg_reg_strt pha_stas_tx_low32;
+ struct t_gg_reg_strt pha_stas_tx_high32;
+ struct t_gg_reg_strt dll_sela_after_mask;
+ struct t_gg_reg_strt dll_selb_after_mask;
+
+ struct t_gg_reg_strt dll_delay_100m_backup;
+ struct t_gg_reg_strt dll_delay_200m_backup;
+
+ struct t_gg_reg_strt dll_sela_100m_cfg;
+ struct t_gg_reg_strt dll_sela_200m_cfg;
+ struct t_gg_reg_strt dll_selb_100m_cfg;
+ struct t_gg_reg_strt dll_selb_200m_cfg;
+ struct t_gg_reg_strt dll_selb_100m_cfg_en;
+ struct t_gg_reg_strt dll_selb_200m_cfg_en;
+ struct t_gg_reg_strt internl_tuning_en_100m;
+ struct t_gg_reg_strt internl_tuning_en_200m;
+ struct t_gg_reg_strt cmd19_cnt_cfg;
+
+ struct t_gg_reg_strt inject_failure_for_tuning_enable_cfg;
+ struct t_gg_reg_strt inject_failure_for_200m_tuning_cfg;
+ struct t_gg_reg_strt inject_failure_for_100m_tuning_cfg;
+
+ int def_sela_100m;
+ int def_sela_200m;
+ int def_selb_100m;
+ int def_selb_200m;
+
+ u32 _gg_reg_cur[16];
+ u8 _cur_read_buf[512];
+
+ bool dll_unlock_reinit_flg;
+ u8 driver_strength_reinit_flg;
+ bool tuning_cmd7_timeout_reinit_flg;
+ u32 tuning_cmd7_timeout_reinit_cnt;
+ u32 ggc_cur_sela;
+ bool selx_tuning_done_flag;
+ u32 ggc_cmd_tx_selb_failed_range;
+ int ggc_sw_selb_tuning_first_selb;
+ enum tuning_stat_et ggc_sela_tuning_result[11];
+ int dll_voltage_scan_map[4];
+ int cur_dll_voltage_idx;
+ int sdr50_notuning_sela_inject_flag;
+ int sdr50_notuning_crc_error_flag;
+ u32 sdr50_notuning_sela_rx_inject;
+ u32 bh201_sdr50_sela_sw_inject;
+ u32 bh201_sdr50_selb_hw_inject;
+ u32 bh201_sdr104_selb_hw_inject;
+ u32 bh201_drive_strength;
+ bool tuning_in_progress;
+ int bh201_used;
+ int pwr_gpio; /* External power enable pin for Redriver IC */
+ int det_gpio;
+};
+
+struct sdhci_msm_bayhub_offset {
+ u32 core_hc_mode;
+ u32 core_mci_data_cnt;
+ u32 core_mci_status;
+ u32 core_mci_fifo_cnt;
+ u32 core_mci_version;
+ u32 core_generics;
+ u32 core_testbus_config;
+ u32 core_testbus_sel2_bit;
+ u32 core_testbus_ena;
+ u32 core_testbus_sel2;
+ u32 core_pwrctl_status;
+ u32 core_pwrctl_mask;
+ u32 core_pwrctl_clear;
+ u32 core_pwrctl_ctl;
+ u32 core_sdcc_debug_reg;
+ u32 core_dll_config;
+ u32 core_dll_status;
+ u32 core_vendor_spec;
+ u32 core_vendor_spec_adma_err_addr0;
+ u32 core_vendor_spec_adma_err_addr1;
+ u32 core_vendor_spec_func2;
+ u32 core_vendor_spec_capabilities0;
+ u32 core_ddr_200_cfg;
+ u32 core_vendor_spec3;
+ u32 core_dll_config_2;
+ u32 core_dll_config_3;
+ u32 core_ddr_config_old; /* Applicable to sdcc minor ver < 0x49 */
+ u32 core_ddr_config;
+ u32 core_dll_usr_ctl; /* Present on SDCC5.1 onwards */
+};
+
+static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_v5_offset = {
+ .core_mci_data_cnt = 0x35c,
+ .core_mci_status = 0x324,
+ .core_mci_fifo_cnt = 0x308,
+ .core_mci_version = 0x318,
+ .core_generics = 0x320,
+ .core_testbus_config = 0x32c,
+ .core_testbus_sel2_bit = 3,
+ .core_testbus_ena = (1 << 31),
+ .core_testbus_sel2 = (1 << 3),
+ .core_pwrctl_status = 0x240,
+ .core_pwrctl_mask = 0x244,
+ .core_pwrctl_clear = 0x248,
+ .core_pwrctl_ctl = 0x24c,
+ .core_sdcc_debug_reg = 0x358,
+ .core_dll_config = 0x200,
+ .core_dll_status = 0x208,
+ .core_vendor_spec = 0x20c,
+ .core_vendor_spec_adma_err_addr0 = 0x214,
+ .core_vendor_spec_adma_err_addr1 = 0x218,
+ .core_vendor_spec_func2 = 0x210,
+ .core_vendor_spec_capabilities0 = 0x21c,
+ .core_ddr_200_cfg = 0x224,
+ .core_vendor_spec3 = 0x250,
+ .core_dll_config_2 = 0x254,
+ .core_dll_config_3 = 0x258,
+ .core_ddr_config = 0x25c,
+ .core_dll_usr_ctl = 0x388,
+};
+
+static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_mci_offset = {
+ .core_hc_mode = 0x78,
+ .core_mci_data_cnt = 0x30,
+ .core_mci_status = 0x34,
+ .core_mci_fifo_cnt = 0x44,
+ .core_mci_version = 0x050,
+ .core_generics = 0x70,
+ .core_testbus_config = 0x0cc,
+ .core_testbus_sel2_bit = 4,
+ .core_testbus_ena = (1 << 3),
+ .core_testbus_sel2 = (1 << 4),
+ .core_pwrctl_status = 0xdc,
+ .core_pwrctl_mask = 0xe0,
+ .core_pwrctl_clear = 0xe4,
+ .core_pwrctl_ctl = 0xe8,
+ .core_sdcc_debug_reg = 0x124,
+ .core_dll_config = 0x100,
+ .core_dll_status = 0x108,
+ .core_vendor_spec = 0x10c,
+ .core_vendor_spec_adma_err_addr0 = 0x114,
+ .core_vendor_spec_adma_err_addr1 = 0x118,
+ .core_vendor_spec_func2 = 0x110,
+ .core_vendor_spec_capabilities0 = 0x11c,
+ .core_ddr_200_cfg = 0x184,
+ .core_vendor_spec3 = 0x1b0,
+ .core_dll_config_2 = 0x1b4,
+ .core_ddr_config_old = 0x1b8,
+ .core_ddr_config = 0x1bc,
+};
+
+struct sdhci_msm_bayhub_variant_ops {
+ u32 (*msm_bayhub_readl_relaxed)(struct sdhci_host *host, u32 offset);
+ void (*msm_bayhub_writel_relaxed)(u32 val, struct sdhci_host *host,
+ u32 offset);
+};
+
+/*
+ * From V5, register spaces have changed. Wrap this info in a structure
+ * and choose the data_structure based on version info mentioned in DT.
+ */
+struct sdhci_msm_bayhub_variant_info {
+ bool mci_removed;
+ bool restore_dll_config;
+ bool uses_tassadar_dll;
+ const struct sdhci_msm_bayhub_variant_ops *var_ops;
+ const struct sdhci_msm_bayhub_offset *offset;
+};
+
+struct sdhci_msm_bayhub_host {
+ struct platform_device *pdev;
+ void __iomem *core_mem; /* MSM SDCC mapped address */
+ int pwr_irq; /* power irq */
+ struct clk *bus_clk; /* SDHC bus voter clock */
+ struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/
+ struct clk_bulk_data bulk_clks[4]; /* core, iface, cal, sleep clocks */
+ unsigned long clk_rate;
+ struct mmc_host *mmc;
+ struct opp_table *opp_table;
+ bool has_opp_table;
+ bool use_14lpp_dll_reset;
+ bool tuning_done;
+ bool calibration_done;
+ u8 saved_tuning_phase;
+ bool use_cdclp533;
+ u32 curr_pwr_state;
+ u32 curr_io_level;
+ wait_queue_head_t pwr_irq_wait;
+ bool pwr_irq_flag;
+ u32 caps_0;
+ bool mci_removed;
+ bool restore_dll_config;
+ const struct sdhci_msm_bayhub_variant_ops *var_ops;
+ const struct sdhci_msm_bayhub_offset *offset;
+ bool use_cdr;
+ u32 transfer_mode;
+ bool updated_ddr_cfg;
+ bool uses_tassadar_dll;
+ u32 dll_config;
+ u32 ddr_config;
+ bool vqmmc_enabled;
+ struct ggc_platform_t ggc;
+};
+
+static const struct sdhci_msm_bayhub_offset *sdhci_priv_msm_bayhub_offset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ return msm_bayhub_host->offset;
+}
+
+/*
+ * APIs to read/write to vendor specific registers which were there in the
+ * core_mem region before MCI was removed.
+ */
+static u32 sdhci_msm_bayhub_mci_variant_readl_relaxed(struct sdhci_host *host,
+ u32 offset)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ return readl_relaxed(msm_bayhub_host->core_mem + offset);
+}
+
+static u32 sdhci_msm_bayhub_v5_variant_readl_relaxed(struct sdhci_host *host,
+ u32 offset)
+{
+ return readl_relaxed(host->ioaddr + offset);
+}
+
+static void sdhci_msm_bayhub_mci_variant_writel_relaxed(u32 val,
+ struct sdhci_host *host, u32 offset)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ writel_relaxed(val, msm_bayhub_host->core_mem + offset);
+}
+
+static void sdhci_msm_bayhub_v5_variant_writel_relaxed(u32 val,
+ struct sdhci_host *host, u32 offset)
+{
+ writel_relaxed(val, host->ioaddr + offset);
+}
+
+static unsigned int msm_bayhub_get_clock_mult_for_bus_mode(struct sdhci_host *host)
+{
+ struct mmc_ios ios = host->mmc->ios;
+ /*
+ * The SDHC requires internal clock frequency to be double the
+ * actual clock that will be set for DDR mode. The controller
+ * uses the faster clock(100/400MHz) for some of its parts and
+ * send the actual required clock (50/200MHz) to the card.
+ */
+ if (ios.timing == MMC_TIMING_UHS_DDR50 ||
+ ios.timing == MMC_TIMING_MMC_DDR52 ||
+ ios.timing == MMC_TIMING_MMC_HS400 ||
+ host->flags & SDHCI_HS400_TUNING)
+ return 2;
+ return 1;
+}
+
+static void msm_bayhub_set_clock_rate_for_bus_mode(struct sdhci_host *host,
+ unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_ios curr_ios = host->mmc->ios;
+ struct clk *core_clk = msm_bayhub_host->bulk_clks[0].clk;
+ unsigned long achieved_rate;
+ unsigned int desired_rate;
+ unsigned int mult;
+ int rc;
+
+ mult = msm_bayhub_get_clock_mult_for_bus_mode(host);
+ desired_rate = clock * mult;
+ rc = dev_pm_opp_set_rate(mmc_dev(host->mmc), desired_rate);
+ if (rc) {
+ pr_err("%s: Failed to set clock at rate %u at timing %d\n",
+ mmc_hostname(host->mmc), desired_rate, curr_ios.timing);
+ return;
+ }
+
+ /*
+ * Qualcomm clock drivers by default round clock _up_ if they can't
+ * make the requested rate. This is not good for SD. Yell if we
+ * encounter it.
+ */
+ achieved_rate = clk_get_rate(core_clk);
+ if (achieved_rate > desired_rate)
+ pr_warn("%s: Card appears overclocked; req %u Hz, actual %lu Hz\n",
+ mmc_hostname(host->mmc), desired_rate, achieved_rate);
+ host->mmc->actual_clock = achieved_rate / mult;
+
+ /* Stash the rate we requested to use in sdhci_msm_bayhub_runtime_resume() */
+ msm_bayhub_host->clk_rate = desired_rate;
+
+ pr_debug("%s: Setting clock at rate %lu at timing %d\n",
+ mmc_hostname(host->mmc), achieved_rate, curr_ios.timing);
+}
+
+/* Platform specific tuning */
+static inline int msm_bayhub_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll)
+{
+ u32 wait_cnt = 50;
+ u8 ck_out_en;
+ struct mmc_host *mmc = host->mmc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ /* Poll for CK_OUT_EN bit. max. poll time = 50us */
+ ck_out_en = !!(readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config) & CORE_CK_OUT_EN);
+
+ while (ck_out_en != poll) {
+ if (--wait_cnt == 0) {
+ dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n",
+ mmc_hostname(mmc), poll);
+ return -ETIMEDOUT;
+ }
+ udelay(1);
+
+ ck_out_en = !!(readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config) & CORE_CK_OUT_EN);
+ }
+
+ return 0;
+}
+
+static int msm_bayhub_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
+{
+ int rc;
+ static const u8 grey_coded_phase_table[] = {
+ 0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4,
+ 0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8
+ };
+ unsigned long flags;
+ u32 config;
+ struct mmc_host *mmc = host->mmc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ if (phase > 0xf)
+ return -EINVAL;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN);
+ config |= (CORE_CDR_EXT_EN | CORE_DLL_EN);
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */
+ rc = msm_bayhub_dll_poll_ck_out_en(host, 0);
+ if (rc)
+ goto err_out;
+
+ /*
+ * Write the selected DLL clock output phase (0 ... 15)
+ * to CDR_SELEXT bit field of DLL_CONFIG register.
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~CDR_SELEXT_MASK;
+ config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
+ rc = msm_bayhub_dll_poll_ck_out_en(host, 1);
+ if (rc)
+ goto err_out;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CDR_EN;
+ config &= ~CORE_CDR_EXT_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+ goto out;
+
+err_out:
+ dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n",
+ mmc_hostname(mmc), phase);
+out:
+ spin_unlock_irqrestore(&host->lock, flags);
+ return rc;
+}
+
+/*
+ * Find out the greatest range of consecuitive selected
+ * DLL clock output phases that can be used as sampling
+ * setting for SD3.0 UHS-I card read operation (in SDR104
+ * timing mode) or for eMMC4.5 card read operation (in
+ * HS400/HS200 timing mode).
+ * Select the 3/4 of the range and configure the DLL with the
+ * selected DLL clock output phase.
+ */
+
+static int msm_bayhub_find_most_appropriate_phase(struct sdhci_host *host,
+ u8 *phase_table, u8 total_phases)
+{
+ int ret;
+ u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} };
+ u8 phases_per_row[MAX_PHASES] = { 0 };
+ int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0;
+ int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0;
+ bool phase_0_found = false, phase_15_found = false;
+ struct mmc_host *mmc = host->mmc;
+
+ if (!total_phases || (total_phases > MAX_PHASES)) {
+ dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n",
+ mmc_hostname(mmc), total_phases);
+ return -EINVAL;
+ }
+
+ for (cnt = 0; cnt < total_phases; cnt++) {
+ ranges[row_index][col_index] = phase_table[cnt];
+ phases_per_row[row_index] += 1;
+ col_index++;
+
+ if ((cnt + 1) == total_phases) {
+ continue;
+ /* check if next phase in phase_table is consecutive or not */
+ } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) {
+ row_index++;
+ col_index = 0;
+ }
+ }
+
+ if (row_index >= MAX_PHASES)
+ return -EINVAL;
+
+ /* Check if phase-0 is present in first valid window? */
+ if (!ranges[0][0]) {
+ phase_0_found = true;
+ phase_0_raw_index = 0;
+ /* Check if cycle exist between 2 valid windows */
+ for (cnt = 1; cnt <= row_index; cnt++) {
+ if (phases_per_row[cnt]) {
+ for (i = 0; i < phases_per_row[cnt]; i++) {
+ if (ranges[cnt][i] == 15) {
+ phase_15_found = true;
+ phase_15_raw_index = cnt;
+ break;
+ }
+ }
+ }
+ }
+ }
+
+ /* If 2 valid windows form cycle then merge them as single window */
+ if (phase_0_found && phase_15_found) {
+ /* number of phases in raw where phase 0 is present */
+ u8 phases_0 = phases_per_row[phase_0_raw_index];
+ /* number of phases in raw where phase 15 is present */
+ u8 phases_15 = phases_per_row[phase_15_raw_index];
+
+ if (phases_0 + phases_15 >= MAX_PHASES)
+ /*
+ * If there are more than 1 phase windows then total
+ * number of phases in both the windows should not be
+ * more than or equal to MAX_PHASES.
+ */
+ return -EINVAL;
+
+ /* Merge 2 cyclic windows */
+ i = phases_15;
+ for (cnt = 0; cnt < phases_0; cnt++) {
+ ranges[phase_15_raw_index][i] =
+ ranges[phase_0_raw_index][cnt];
+ if (++i >= MAX_PHASES)
+ break;
+ }
+
+ phases_per_row[phase_0_raw_index] = 0;
+ phases_per_row[phase_15_raw_index] = phases_15 + phases_0;
+ }
+
+ for (cnt = 0; cnt <= row_index; cnt++) {
+ if (phases_per_row[cnt] > curr_max) {
+ curr_max = phases_per_row[cnt];
+ selected_row_index = cnt;
+ }
+ }
+
+ i = (curr_max * 3) / 4;
+ if (i)
+ i--;
+
+ ret = ranges[selected_row_index][i];
+
+ if (ret >= MAX_PHASES) {
+ ret = -EINVAL;
+ dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n",
+ mmc_hostname(mmc), ret);
+ }
+
+ return ret;
+}
+
+static inline void msm_bayhub_cm_dll_set_freq(struct sdhci_host *host)
+{
+ u32 mclk_freq = 0, config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ /* Program the MCLK value to MCLK_FREQ bit field */
+ if (host->clock <= 112000000)
+ mclk_freq = 0;
+ else if (host->clock <= 125000000)
+ mclk_freq = 1;
+ else if (host->clock <= 137000000)
+ mclk_freq = 2;
+ else if (host->clock <= 150000000)
+ mclk_freq = 3;
+ else if (host->clock <= 162000000)
+ mclk_freq = 4;
+ else if (host->clock <= 175000000)
+ mclk_freq = 5;
+ else if (host->clock <= 187000000)
+ mclk_freq = 6;
+ else if (host->clock <= 200000000)
+ mclk_freq = 7;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~CMUX_SHIFT_PHASE_MASK;
+ config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+}
+
+/* Initialize the DLL (Programmable Delay Line) */
+static int msm_bayhub_init_cm_dll(struct sdhci_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int wait_cnt = 50;
+ unsigned long flags, xo_clk = 0;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ if (msm_bayhub_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_bayhub_host->xo_clk))
+ xo_clk = clk_get_rate(msm_bayhub_host->xo_clk);
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ /*
+ * Make sure that clock is always enabled when DLL
+ * tuning is in progress. Keeping PWRSAVE ON may
+ * turn off the clock.
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_CLK_PWRSAVE;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ if (msm_bayhub_host->dll_config)
+ writel_relaxed(msm_bayhub_host->dll_config,
+ host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config |= CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ if (!msm_bayhub_host->dll_config)
+ msm_bayhub_cm_dll_set_freq(host);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset &&
+ !IS_ERR_OR_NULL(msm_bayhub_host->xo_clk)) {
+ u32 mclk_freq = 0;
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= CORE_FLL_CYCLE_CNT;
+ if (config)
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8),
+ xo_clk);
+ else
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4),
+ xo_clk);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= ~(0xFF << 10);
+ config |= mclk_freq << 10;
+
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ /* wait for 5us before enabling DLL clock */
+ udelay(5);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset) {
+ if (!msm_bayhub_host->dll_config)
+ msm_bayhub_cm_dll_set_freq(host);
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= ~CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ }
+
+ /*
+ * Configure DLL user control register to enable DLL status.
+ * This setting is applicable to SDCC v5.1 onwards only.
+ */
+ if (msm_bayhub_host->uses_tassadar_dll) {
+ config = DLL_USR_CTL_POR_VAL | FINE_TUNE_MODE_EN |
+ ENABLE_DLL_LOCK_STATUS | BIAS_OK_SIGNAL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_usr_ctl);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_3);
+ config &= ~0xFF;
+ if (msm_bayhub_host->clk_rate < 150000000)
+ config |= DLL_CONFIG_3_LOW_FREQ_VAL;
+ else
+ config |= DLL_CONFIG_3_HIGH_FREQ_VAL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_3);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
+ while (!(readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_status) &
+ CORE_DLL_LOCK)) {
+ /* max. wait for 50us sec for LOCK bit to be set */
+ if (--wait_cnt == 0) {
+ dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
+ mmc_hostname(mmc));
+ spin_unlock_irqrestore(&host->lock, flags);
+ return -ETIMEDOUT;
+ }
+ udelay(1);
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+ return 0;
+}
+
+static void msm_bayhub_hc_select_default(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ if (!msm_bayhub_host->use_cdclp533) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ config &= ~CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_DFLT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ /*
+ * Disable HC_SELECT_IN to be able to use the UHS mode select
+ * configuration from Host Control2 register for all other
+ * modes.
+ * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field
+ * in VENDOR_SPEC_FUNC
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_SELECT_IN_EN;
+ config &= ~CORE_HC_SELECT_IN_MASK;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ /*
+ * Make sure above writes impacting free running MCLK are completed
+ * before changing the clk_rate at GCC.
+ */
+ wmb();
+}
+
+static void msm_bayhub_hc_select_hs400(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_ios ios = host->mmc->ios;
+ u32 config, dll_lock;
+ int rc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ /* Select the divided clock (free running MCLK/2) */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_HS400;
+
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ /*
+ * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC
+ * register
+ */
+ if ((msm_bayhub_host->tuning_done || ios.enhanced_strobe) &&
+ !msm_bayhub_host->calibration_done) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ config |= CORE_HC_SELECT_IN_HS400;
+ config |= CORE_HC_SELECT_IN_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ }
+ if (!msm_bayhub_host->clk_rate && !msm_bayhub_host->use_cdclp533) {
+ /*
+ * Poll on DLL_LOCK or DDR_DLL_LOCK bits in
+ * core_dll_status to be set. This should get set
+ * within 15 us at 200 MHz.
+ */
+ rc = readl_relaxed_poll_timeout(host->ioaddr +
+ msm_bayhub_offset->core_dll_status,
+ dll_lock,
+ (dll_lock &
+ (CORE_DLL_LOCK |
+ CORE_DDR_DLL_LOCK)), 10,
+ 1000);
+ if (rc == -ETIMEDOUT)
+ pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n",
+ mmc_hostname(host->mmc), dll_lock);
+ }
+ /*
+ * Make sure above writes impacting free running MCLK are completed
+ * before changing the clk_rate at GCC.
+ */
+ wmb();
+}
+
+/*
+ * sdhci_msm_bayhub_hc_select_mode :- In general all timing modes are
+ * controlled via UHS mode select in Host Control2 register.
+ * eMMC specific HS200/HS400 doesn't have their respective modes
+ * defined here, hence we use these values.
+ *
+ * HS200 - SDR104 (Since they both are equivalent in functionality)
+ * HS400 - This involves multiple configurations
+ * Initially SDR104 - when tuning is required as HS200
+ * Then when switching to DDR @ 400MHz (HS400) we use
+ * the vendor specific HC_SELECT_IN to control the mode.
+ *
+ * In addition to controlling the modes we also need to select the
+ * correct input clock for DLL depending on the mode.
+ *
+ * HS400 - divided clock (free running MCLK/2)
+ * All other modes - default (free running MCLK)
+ */
+static void sdhci_msm_bayhub_hc_select_mode(struct sdhci_host *host)
+{
+ struct mmc_ios ios = host->mmc->ios;
+
+ if (ios.timing == MMC_TIMING_MMC_HS400 ||
+ host->flags & SDHCI_HS400_TUNING)
+ msm_bayhub_hc_select_hs400(host);
+ else
+ msm_bayhub_hc_select_default(host);
+}
+
+static int sdhci_msm_bayhub_cdclp533_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 config, calib_done;
+ int ret;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ /* Set the selected phase in delay line hw block */
+ ret = msm_bayhub_config_cm_dll_phase(host, msm_bayhub_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config &= ~CORE_CDC_T4_DLY_SEL;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config &= ~CORE_CDC_SWITCH_BYPASS_OFF;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config |= CORE_CDC_SWITCH_RC_EN;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config &= ~CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+
+ /* Perform CDC Register Initialization Sequence */
+
+ writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1);
+ writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1);
+ writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG);
+ writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG);
+ writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG);
+ writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG);
+ writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG);
+
+ /* CDC HW Calibration */
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config &= ~CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_HW_AUTOCAL_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ config |= CORE_TIMER_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0,
+ calib_done,
+ (calib_done & CORE_CALIBRATION_DONE),
+ 1, 50);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CDC calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0)
+ & CORE_CDC_ERROR_CODE_MASK;
+ if (ret) {
+ pr_err("%s: %s: CDC error code %d\n",
+ mmc_hostname(host->mmc), __func__, ret);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config |= CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_cm_dll_sdc4_calibration(struct sdhci_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ u32 dll_status, config, ddr_cfg_offset;
+ int ret;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Currently the core_ddr_config register defaults to desired
+ * configuration on reset. Currently reprogramming the power on
+ * reset (POR) value in case it might have been modified by
+ * bootloaders. In the future, if this changes, then the desired
+ * values will need to be programmed appropriately.
+ */
+ if (msm_bayhub_host->updated_ddr_cfg)
+ ddr_cfg_offset = msm_bayhub_offset->core_ddr_config;
+ else
+ ddr_cfg_offset = msm_bayhub_offset->core_ddr_config_old;
+ writel_relaxed(msm_bayhub_host->ddr_config, host->ioaddr + ddr_cfg_offset);
+
+ if (mmc->ios.enhanced_strobe) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_ddr_200_cfg);
+ config |= CORE_CMDIN_RCLK_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_ddr_200_cfg);
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_2);
+ config |= CORE_DDR_CAL_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config_2);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr +
+ msm_bayhub_offset->core_dll_status,
+ dll_status,
+ (dll_status & CORE_DDR_DLL_LOCK),
+ 10, 1000);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ /*
+ * Set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3.
+ * When MCLK is gated OFF, it is not gated for less than 0.5us
+ * and MCLK must be switched on for at-least 1us before DATA
+ * starts coming. Controllers with 14lpp and later tech DLL cannot
+ * guarantee above requirement. So PWRSAVE_DLL should not be
+ * turned on for host controllers using this DLL.
+ */
+ if (!msm_bayhub_host->use_14lpp_dll_reset) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ config |= CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ }
+
+ /*
+ * Drain writebuffer to ensure above DLL calibration
+ * and PWRSAVE DLL is enabled.
+ */
+ wmb();
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_hs400_dll_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_host *mmc = host->mmc;
+ int ret;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ if (!mmc->ios.enhanced_strobe) {
+ /* Set the selected phase in delay line hw block */
+ ret = msm_bayhub_config_cm_dll_phase(host,
+ msm_bayhub_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ }
+
+ if (msm_bayhub_host->use_cdclp533)
+ ret = sdhci_msm_bayhub_cdclp533_calibration(host);
+ else
+ ret = sdhci_msm_bayhub_cm_dll_sdc4_calibration(host);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static bool sdhci_msm_bayhub_is_tuning_needed(struct sdhci_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+
+ /*
+ * Tuning is required for SDR104, HS200 and HS400 cards and
+ * if clock frequency is greater than 100MHz in these modes.
+ */
+ if (host->clock <= CORE_FREQ_100MHZ ||
+ !(ios->timing == MMC_TIMING_MMC_HS400 ||
+ ios->timing == MMC_TIMING_MMC_HS200 ||
+ ios->timing == MMC_TIMING_UHS_SDR104) ||
+ ios->enhanced_strobe)
+ return false;
+
+ return true;
+}
+
+static int sdhci_msm_bayhub_restore_sdr_dll_config(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ /*
+ * SDR DLL comes into picture only for timing modes which needs
+ * tuning.
+ */
+ if (!sdhci_msm_bayhub_is_tuning_needed(host))
+ return 0;
+
+ /* Reset the tuning block */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ return ret;
+
+ /* Restore the tuning block */
+ ret = msm_bayhub_config_cm_dll_phase(host, msm_bayhub_host->saved_tuning_phase);
+
+ return ret;
+}
+
+static void sdhci_msm_bayhub_set_cdr(struct sdhci_host *host, bool enable)
+{
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+ u32 config, oldconfig = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = oldconfig;
+ if (enable) {
+ config |= CORE_CDR_EN;
+ config &= ~CORE_CDR_EXT_EN;
+ } else {
+ config &= ~CORE_CDR_EN;
+ config |= CORE_CDR_EXT_EN;
+ }
+
+ if (config != oldconfig) {
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ }
+}
+
+static int sdhci_msm_bayhub_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ int tuning_seq_cnt = 10;
+ u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
+ int rc;
+ struct mmc_ios ios = host->mmc->ios;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!sdhci_msm_bayhub_is_tuning_needed(host)) {
+ msm_bayhub_host->use_cdr = false;
+ sdhci_msm_bayhub_set_cdr(host, false);
+ return 0;
+ }
+
+ /* Clock-Data-Recovery used to dynamically adjust RX sampling point */
+ msm_bayhub_host->use_cdr = true;
+
+ /*
+ * Clear tuning_done flag before tuning to ensure proper
+ * HS400 settings.
+ */
+ msm_bayhub_host->tuning_done = 0;
+
+ /*
+ * For HS400 tuning in HS200 timing requires:
+ * - select MCLK/2 in VENDOR_SPEC
+ * - program MCLK to 400MHz (or nearest supported) in GCC
+ */
+ if (host->flags & SDHCI_HS400_TUNING) {
+ sdhci_msm_bayhub_hc_select_mode(host);
+ msm_bayhub_set_clock_rate_for_bus_mode(host, ios.clock);
+ host->flags &= ~SDHCI_HS400_TUNING;
+ }
+
+retry:
+ /* First of all reset the tuning block */
+ rc = msm_bayhub_init_cm_dll(host);
+ if (rc)
+ return rc;
+
+ phase = 0;
+ do {
+ /* Set the phase in delay line hw block */
+ rc = msm_bayhub_config_cm_dll_phase(host, phase);
+ if (rc)
+ return rc;
+
+ rc = mmc_send_tuning(mmc, opcode, NULL);
+ if (!rc) {
+ /* Tuning is successful at this tuning point */
+ tuned_phases[tuned_phase_cnt++] = phase;
+ dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
+ mmc_hostname(mmc), phase);
+ }
+
+ if (msm_bayhub_host->ggc.bh201_used)
+ usleep_range(1000, 1200);
+
+ } while (++phase < ARRAY_SIZE(tuned_phases));
+
+ if (tuned_phase_cnt) {
+ if (tuned_phase_cnt == ARRAY_SIZE(tuned_phases)) {
+ /*
+ * All phases valid is _almost_ as bad as no phases
+ * valid. Probably all phases are not really reliable
+ * but we didn't detect where the unreliable place is.
+ * That means we'll essentially be guessing and hoping
+ * we get a good phase. Better to try a few times.
+ */
+ dev_dbg(mmc_dev(mmc), "%s: All phases valid; try again\n",
+ mmc_hostname(mmc));
+ if (--tuning_seq_cnt) {
+ tuned_phase_cnt = 0;
+ goto retry;
+ }
+ }
+
+ rc = msm_bayhub_find_most_appropriate_phase(host, tuned_phases,
+ tuned_phase_cnt);
+ if (rc >= 0)
+ phase = rc;
+ else
+ return rc;
+
+ /*
+ * Finally set the selected phase in delay
+ * line hw block.
+ */
+ rc = msm_bayhub_config_cm_dll_phase(host, phase);
+ if (rc)
+ return rc;
+ msm_bayhub_host->saved_tuning_phase = phase;
+ dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
+ mmc_hostname(mmc), phase);
+ } else {
+ if (--tuning_seq_cnt)
+ goto retry;
+ /* Tuning failed */
+ dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n",
+ mmc_hostname(mmc));
+ rc = -EIO;
+ }
+
+ if (!rc)
+ msm_bayhub_host->tuning_done = true;
+ return rc;
+}
+
+static const unsigned int freqs[] = { 400000, 300000, 200000, 100000 };
+
+static void cfg_bit_2_bt(int max_bit, int tar, int *byt, int *bit)
+{
+ struct rl_bit_lct cfg_bit_map[6] = {
+ {0, 6}, {1, 5}, {2, 4},
+ {3, 2}, {4, 1}, {5, 0},
+ };
+
+ *byt = (max_bit - tar) / 6;
+ *bit = cfg_bit_map[(max_bit - tar) % 6].rl_bits;
+}
+
+static u32 cfg_read_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+ return rv;
+}
+
+static void get_default_setting(struct sdhci_host *host, u8 *data)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ vendor_host->ggc.def_sela_100m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
+ vendor_host->ggc.def_sela_200m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
+ vendor_host->ggc.def_selb_100m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
+ vendor_host->ggc.def_selb_200m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
+}
+
+static void cfg_write_bits_ofs_mask(u8 *cfg,
+ struct t_gg_reg_strt *bts, u32 w_value)
+{
+ u32 wv = w_value & bts->mask;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
+ if (wv & 1)
+ cfg[byt] |= (u8) (1 << bit);
+ else
+ cfg[byt] &= (u8) (~(1 << bit));
+
+ i++;
+ wv >>= 1;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+}
+
+static void ram_bit_2_bt(int tar, int *byt, int *bit)
+{
+ *byt = tar / 8;
+ *bit = tar % 8;
+}
+
+static void set_gg_reg_cur_val(struct ggc_platform_t *ggc,
+ u8 *data, u8 len)
+{
+ memcpy(&ggc->_gg_reg_cur[0], data, len);
+}
+
+static void get_gg_reg_cur_val(struct ggc_platform_t *ggc,
+ u8 *data, u8 len)
+{
+ memcpy(data, &ggc->_gg_reg_cur[0], len);
+}
+
+static void get_gg_reg_def(struct sdhci_host *host, u8 *data)
+{
+ u32 gg_sw_def[16] = GGC_CFG_DATA;
+
+ memcpy(data, (u8 *)&(gg_sw_def[0]), sizeof(gg_sw_def));
+}
+
+static u32 read_ram_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ ram_bit_2_bt(bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+
+ } while (1);
+ return rv;
+}
+
+static void ggc_dll_voltage_init(struct sdhci_host *host)
+{
+ int i = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ for (i = 0; i < 4; i++) {
+ vendor_host->ggc.dll_voltage_scan_map[i] = 0;
+ vendor_host->ggc.sdr50.dll_voltage_unlock_cnt[i] = 0;
+ vendor_host->ggc.sdr104.dll_voltage_unlock_cnt[i] = 0;
+ }
+}
+
+static void ggc_chip_init(struct sdhci_host *host)
+{
+ u8 data[512] = { 0 };
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_def(host, data);
+ get_default_setting(host, data);
+ set_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+}
+
+static int driver_send_command7(struct sdhci_host *host)
+{
+ int ret = 0;
+ int err;
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_command cmd = {0};
+
+ cmd.opcode = MMC_SELECT_CARD;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+ err = mmc_wait_for_cmd(mmc, &cmd, 3);
+ if (err)
+ ret = 0;
+ else
+ ret = 1;
+
+ return ret;
+}
+
+static void driver_send_command24(struct sdhci_host *host,
+ u32 *cfg_data, int data_len)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_request mrq = {0};
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+
+ memcpy(data1, (u8 *)&(cfg_data[0]), data_len);
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_WRITE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_WRITE;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+ kfree(data1);
+}
+
+static void bht_update_cfg(struct mmc_host *mmc_host,
+ struct mmc_card *card, u32 *cfg_data, int data_len)
+{
+ int ret = 0;
+ struct sdhci_host *host;
+
+ host = mmc_priv(mmc_host);
+ mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_4);
+ if (host->ops->reset)
+ host->ops->reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
+
+ driver_send_command7(host);
+ driver_send_command24(host, cfg_data, data_len);
+ driver_send_command7(host);
+
+ mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_1);
+}
+
+
+static void tx_selb_failed_tb_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ memset(&vendor_host->ggc.sdr104.tx_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr104.tx_selb_tb));
+ memset(&vendor_host->ggc.sdr50.tx_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr50.tx_selb_tb));
+}
+
+static void all_selb_failed_tb_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ memset(vendor_host->ggc.sdr104.all_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr104.all_selb_tb));
+ memset(vendor_host->ggc.sdr50.all_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr50.all_selb_tb));
+}
+
+static void tx_selb_failed_history_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ vendor_host->ggc.sdr50.tx_selb_failed_history = BIT_PASS_MASK;
+ vendor_host->ggc.sdr104.tx_selb_failed_history = BIT_PASS_MASK;
+}
+
+static void ggc_reset_selx_failed_tb(struct sdhci_host *host)
+{
+ tx_selb_failed_tb_reset(host);
+ all_selb_failed_tb_reset(host);
+ tx_selb_failed_history_reset(host);
+}
+
+static void _ggc_reset_sela_tuning_result(
+ struct sdhci_msm_bayhub_host *host)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ host->ggc.ggc_sela_tuning_result[i] = NO_TUNING;
+}
+
+static void _ggc_reset_tuning_result_for_dll(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ ggc_reset_selx_failed_tb(host);
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range = BIT_PASS_MASK;
+ vendor_host->ggc.selx_tuning_done_flag = 0;
+ _ggc_reset_sela_tuning_result(vendor_host);
+}
+
+static void ggc_tuning_result_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ _ggc_reset_tuning_result_for_dll(host);
+
+ vendor_host->ggc.sdr50.bus_mode = SD_FNC_AM_SDR50;
+ vendor_host->ggc.sdr104.bus_mode = SD_FNC_AM_SDR104;
+ vendor_host->ggc.driver_strength_reinit_flg = 0;
+ vendor_host->ggc.cur_bus_mode = NULL;
+ vendor_host->ggc.dll_unlock_reinit_flg = 0;
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 0;
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_cnt = 0;
+ vendor_host->ggc.sdr50_notuning_sela_inject_flag = 1;
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 0;
+ if (vendor_host->ggc.bh201_sdr50_sela_sw_inject)
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject =
+ vendor_host->ggc.bh201_sdr50_sela_sw_inject;
+ else
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject = 0x47F;
+}
+
+static void bht_load_hw_inject(struct mmc_host *mmc_host,
+ struct mmc_card *card, u32 *cfg_data, int data_len,
+ u32 sel200, u32 sel100)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+ u32 gg_hw_inj[16] = GGC_CFG_DATA;
+
+ gg_hw_inj[1] = 0x7364032;
+
+ if (vendor_host->ggc.bh201_sdr104_selb_hw_inject)
+ gg_hw_inj[11] = vendor_host->ggc.bh201_sdr104_selb_hw_inject;
+ else
+ gg_hw_inj[11] = 0x57336200;
+
+ if (vendor_host->ggc.bh201_sdr50_selb_hw_inject)
+ gg_hw_inj[12] = vendor_host->ggc.bh201_sdr50_selb_hw_inject;
+ else
+ gg_hw_inj[12] = 0x00725777;
+
+ if (vendor_host->ggc.bh201_drive_strength)
+ gg_hw_inj[15] = vendor_host->ggc.bh201_drive_strength;
+
+ bht_update_cfg(mmc_host, card, gg_hw_inj, data_len);
+}
+
+static void bht_load(struct mmc_host *mmc_host, struct mmc_card *card)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+ u8 driver_strength_reinit_flg =
+ vendor_host->ggc.driver_strength_reinit_flg;
+ int cur_dll_voltage_idx = vendor_host->ggc.cur_dll_voltage_idx;
+ u32 i = 0;
+ u32 reg;
+ u32 gg_sw_def[16] = GGC_CFG_DATA;
+ u8 data[512];
+ static const int s_dll_voltage_cfg[4][2] = {
+ {0x30503106, 0x64141711},
+ {0x31503106, 0x64141711},
+ {0x30503106, 0x64141751},
+ {0x31503106, 0x64141751},
+ };
+
+ if (vendor_host->ggc.bh201_used) {
+ pr_debug("%s: Load BHT patch\n", mmc_hostname(mmc_host));
+
+ mmc_send_relative_addr(mmc_host, &card->rca);
+ mmc_host->card = card;
+ if (vendor_host->ggc.dll_unlock_reinit_flg) {
+ pr_debug("dll unlock reinit: idx=%d\n",
+ cur_dll_voltage_idx);
+ ggc_tuning_result_reset(host);
+ gg_sw_def[8] = s_dll_voltage_cfg[cur_dll_voltage_idx][0];
+ gg_sw_def[9] = s_dll_voltage_cfg[cur_dll_voltage_idx][1];
+ }
+ if (vendor_host->ggc.driver_strength_reinit_flg) {
+ pr_debug("%s: driver strength should be init to %d\n",
+ mmc_hostname(mmc_host), driver_strength_reinit_flg);
+ ggc_tuning_result_reset(host);
+ if (vendor_host->ggc.driver_strength_reinit_flg <= 7) {
+ gg_sw_def[15] &= 0x0f0fffff;
+ gg_sw_def[15] |= (driver_strength_reinit_flg << 28)
+ | (driver_strength_reinit_flg << 20);
+ }
+ }
+ driver_send_command7(host);
+ if (vendor_host->ggc.tuning_cmd7_timeout_reinit_flg == 0
+ && vendor_host->ggc.selx_tuning_done_flag == 0) {
+ bht_load_hw_inject(mmc_host, card, gg_sw_def,
+ sizeof(gg_sw_def), 0x3ff, 0x77f);
+ bht_update_cfg(mmc_host, card, gg_sw_def, sizeof(gg_sw_def));
+ set_gg_reg_cur_val(&vendor_host->ggc, (u8 *)gg_sw_def, sizeof(gg_sw_def));
+ } else {
+ if (vendor_host->ggc.selx_tuning_done_flag)
+ pr_debug("%s: skip load default configuration for tuning done\n",
+ mmc_hostname(mmc_host));
+ if (vendor_host->ggc.tuning_cmd7_timeout_reinit_flg) {
+ pr_debug("%s: write previous inject results to bh201 for cmd7 timeout flag is set\n",
+ mmc_hostname(mmc_host));
+ get_gg_reg_cur_val(&vendor_host->ggc, data, sizeof(gg_sw_def));
+
+ pr_debug("%s: dump config data before write to bh201\n", __func__);
+ for (i = 0; i < 128; i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("ggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+ bht_update_cfg(mmc_host, card, (u32 *)data, sizeof(data));
+ }
+ }
+ }
+}
+
+static void bh201_signal_voltage_on_off(struct sdhci_host *host, u32 on_off)
+{
+ int card_present_status = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (vendor_host->ggc.bh201_used) {
+ if (gpio_is_valid(vendor_host->ggc.det_gpio)) {
+ card_present_status = gpio_get_value(vendor_host->ggc.det_gpio);
+ pr_debug("%s: detect_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.det_gpio, card_present_status);
+ } else {
+ pr_err("%s: no det_gpio provided\n", mmc_hostname(host->mmc));
+ }
+
+ if (on_off) {
+ pr_debug("%s: apply bht power on patch\n", mmc_hostname(host->mmc));
+
+ ggc_dll_voltage_init(host);
+
+ ggc_chip_init(host);
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ gpio_direction_output(vendor_host->ggc.pwr_gpio, 1);
+ msleep(100);
+ pr_debug("%s: pwr_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio,
+ gpio_get_value(vendor_host->ggc.pwr_gpio));
+ } else {
+ pr_err("%s: no pwr_gpio provided\n", mmc_hostname(host->mmc));
+ }
+ } else {
+ pr_debug("%s: apply bht power off patch\n", mmc_hostname(host->mmc));
+
+ ggc_dll_voltage_init(host);
+
+ if (card_present_status <= 0) {
+ pr_debug("%s: clear tuning result for power off and card removed\n",
+ mmc_hostname(host->mmc));
+ ggc_tuning_result_reset(host);
+ }
+ ggc_chip_init(host);
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ gpio_direction_output(vendor_host->ggc.pwr_gpio, 0);
+ pr_debug("%s: pwr_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio,
+ gpio_get_value(vendor_host->ggc.pwr_gpio));
+ } else {
+ pr_err("%s: no pwr_gpio provided\n", mmc_hostname(host->mmc));
+ }
+ }
+ }
+}
+
+static void sdhci_bh201_parse(struct mmc_host *mmc_host)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct device_node *np = vendor_host->pdev->dev.of_node;
+ struct t_gg_reg_strt index_array[] = {
+ { 14, 0xffffffff, 0 }, { 46, 0xffffffff, 0 },
+ { 205, 0xffffffff, 0 }, { 237, 0xffffffff, 0 },
+ { 141, 0xf, 0 }, { 145, 0xf, 0 },
+ { 83, 0xfff, 0 }, { 95, 0xfff, 0 },
+ { 126, 0xf, 0 }, { 130, 0xf, 0 },
+ { 140, 0xf, 0 }, { 144, 0xf, 0 },
+ { 183, 0x1, 0 }, { 184, 0x1, 0 },
+ { 171, 0x1, 0 }, { 172, 0x1, 0 },
+ { 173, 0x3f, 0 }, { 357, 0x1, 0 },
+ { 93, 0x7ff, 0 }, { 81, 0x7ff, 0 },
+ };
+
+ memcpy(&vendor_host->ggc.pha_stas_rx_low32, &index_array[0],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_rx_high32, &index_array[1],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_tx_low32, &index_array[2],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_tx_high32, &index_array[3],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_sela_after_mask, &index_array[4],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_after_mask, &index_array[5],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.dll_delay_100m_backup, &index_array[6],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_delay_200m_backup, &index_array[7],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.dll_sela_100m_cfg, &index_array[8],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_sela_200m_cfg, &index_array[9],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_100m_cfg, &index_array[10],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_200m_cfg, &index_array[11],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_100m_cfg_en, &index_array[12],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_200m_cfg_en, &index_array[13],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.internl_tuning_en_100m, &index_array[14],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.internl_tuning_en_200m, &index_array[15],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.cmd19_cnt_cfg, &index_array[16],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.inject_failure_for_tuning_enable_cfg,
+ &index_array[17], sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.inject_failure_for_200m_tuning_cfg,
+ &index_array[18], sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.inject_failure_for_100m_tuning_cfg,
+ &index_array[19], sizeof(struct t_gg_reg_strt));
+
+ vendor_host->ggc.bh201_drive_strength = 0;
+ vendor_host->ggc.bh201_sdr50_sela_sw_inject = 0;
+ vendor_host->ggc.bh201_sdr50_selb_hw_inject = 0;
+ vendor_host->ggc.bh201_sdr104_selb_hw_inject = 0;
+ vendor_host->ggc.bh201_used = 1;
+ host->flags |= SDHCI_SDR50_NEEDS_TUNING;
+ host->mmc_host_ops.init_card = bht_load;
+
+ if (of_find_property(np, "bh201_drive_strength", NULL))
+ of_property_read_u32_index(np, "bh201_drive_strength", 0,
+ &vendor_host->ggc.bh201_drive_strength);
+ if (of_find_property(np, "bh201_sdr50_sela_sw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr50_sela_sw_inject", 0,
+ &vendor_host->ggc.bh201_sdr50_sela_sw_inject);
+ if (of_find_property(np, "bh201_sdr50_selb_hw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr50_selb_hw_inject", 0,
+ &vendor_host->ggc.bh201_sdr50_selb_hw_inject);
+ if (of_find_property(np, "bh201_sdr104_selb_hw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr104_selb_hw_inject", 0,
+ &vendor_host->ggc.bh201_sdr104_selb_hw_inject);
+
+ vendor_host->ggc.pwr_gpio = of_get_named_gpio(np, "pwr-gpios", 0);
+ if (!gpio_is_valid(vendor_host->ggc.pwr_gpio))
+ dev_err(&vendor_host->pdev->dev, "no pwr-gpio provided !\n");
+ else
+ dev_info(&vendor_host->pdev->dev, "pwr-gpio provided\n");
+
+ vendor_host->ggc.det_gpio = of_get_named_gpio(np, "det-gpios", 0);
+ if (!gpio_is_valid(vendor_host->ggc.det_gpio))
+ dev_err(&vendor_host->pdev->dev, "no det-gpio provided !\n");
+ else
+ dev_info(&vendor_host->pdev->dev, "det-gpio provided\n");
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ devm_gpio_request_one(&vendor_host->pdev->dev, vendor_host->ggc.pwr_gpio,
+ GPIOF_OUT_INIT_LOW, "sprd-1-pwr");
+ pr_debug("%s: detect_gpio pin %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio);
+ } else {
+ pr_err("%s: no detect_gpio provided\n",
+ mmc_hostname(host->mmc));
+ }
+
+ if (gpio_is_valid(vendor_host->ggc.det_gpio)) {
+ devm_gpio_request_one(&vendor_host->pdev->dev, vendor_host->ggc.det_gpio,
+ GPIOF_DIR_IN, "sprd-1-det");
+ pr_debug("%s: detect_gpio pin %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.det_gpio);
+ } else {
+ pr_err("%s: no detect_gpio provided\n",
+ mmc_hostname(host->mmc));
+ }
+}
+
+static int sd_select_driver_type(struct mmc_card *card, u8 *status)
+{
+ int card_drv_type, drive_strength, drv_type;
+ int err;
+
+ card->drive_strength = 0;
+
+ card_drv_type = card->sw_caps.sd3_drv_type | SD_DRIVER_TYPE_B;
+
+ drive_strength = mmc_select_drive_strength(card,
+ card->sw_caps.uhs_max_dtr,
+ card_drv_type, &drv_type);
+
+ if (drive_strength) {
+ err = mmc_sd_switch(card, 1, 2, drive_strength, status);
+ if (err)
+ return err;
+ if ((status[15] & 0xF) != drive_strength) {
+ pr_warn("%s: Problem setting drive strength!\n",
+ mmc_hostname(card->host));
+ return 0;
+ }
+ card->drive_strength = drive_strength;
+ }
+
+ if (drv_type)
+ mmc_set_driver_type(card->host, drv_type);
+
+ return 0;
+}
+
+/* Get host's max current setting at its current voltage */
+static u32 sd_get_host_max_current(struct mmc_host *host)
+{
+ u32 voltage, max_current;
+
+ voltage = 1 << host->ios.vdd;
+ switch (voltage) {
+ case MMC_VDD_165_195:
+ max_current = host->max_current_180;
+ break;
+ case MMC_VDD_29_30:
+ case MMC_VDD_30_31:
+ max_current = host->max_current_300;
+ break;
+ case MMC_VDD_32_33:
+ case MMC_VDD_33_34:
+ max_current = host->max_current_330;
+ break;
+ default:
+ max_current = 0;
+ }
+
+ return max_current;
+}
+
+static int sd_set_current_limit(struct mmc_card *card, u8 *status)
+{
+ int current_limit = SD_SET_CURRENT_NO_CHANGE;
+ int err;
+ u32 max_current;
+
+ /*
+ * Current limit switch is only defined for SDR50, SDR104, and DDR50
+ * bus speed modes. For other bus speed modes, we do not change the
+ * current limit.
+ */
+ if ((card->sd_bus_speed != UHS_SDR50_BUS_SPEED) &&
+ (card->sd_bus_speed != UHS_SDR104_BUS_SPEED) &&
+ (card->sd_bus_speed != UHS_DDR50_BUS_SPEED))
+ return 0;
+
+ /*
+ * Host has different current capabilities when operating at
+ * different voltages, so find out its max current first.
+ */
+ max_current = sd_get_host_max_current(card->host);
+
+ /*
+ * We only check host's capability here, if we set a limit that is
+ * higher than the card's maximum current, the card will be using its
+ * maximum current, e.g. if the card's maximum current is 300ma, and
+ * when we set current limit to 200ma, the card will draw 200ma, and
+ * when we set current limit to 400/600/800ma, the card will draw its
+ * maximum 300ma from the host.
+ *
+ * The above is incorrect: if we try to set a current limit that is
+ * not supported by the card, the card can rightfully error out the
+ * attempt, and remain at the default current limit. This results
+ * in a 300mA card being limited to 200mA even though the host
+ * supports 800mA. Failures seen with SanDisk 8GB UHS cards with
+ * an iMX6 host. --rmk
+ */
+ if (max_current >= 800 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800)
+ current_limit = SD_SET_CURRENT_LIMIT_800;
+ else if (max_current >= 600 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_600)
+ current_limit = SD_SET_CURRENT_LIMIT_600;
+ else if (max_current >= 400 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400)
+ current_limit = SD_SET_CURRENT_LIMIT_400;
+ else if (max_current >= 200 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200)
+ current_limit = SD_SET_CURRENT_LIMIT_200;
+
+ if (current_limit != SD_SET_CURRENT_NO_CHANGE) {
+ err = mmc_sd_switch(card, 1, 3, current_limit, status);
+ if (err)
+ return err;
+
+ if (((status[15] >> 4) & 0x0F) != current_limit)
+ pr_warn("%s: Problem setting current limit!\n",
+ mmc_hostname(card->host));
+
+ }
+
+ return 0;
+}
+
+static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
+{
+ int err;
+ unsigned int timing = 0;
+
+ switch (card->sd_bus_speed) {
+ case UHS_SDR104_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR104;
+ card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
+ break;
+ case UHS_DDR50_BUS_SPEED:
+ timing = MMC_TIMING_UHS_DDR50;
+ card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
+ break;
+ case UHS_SDR50_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR50;
+ card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
+ break;
+ case UHS_SDR25_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR25;
+ card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
+ break;
+ case UHS_SDR12_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR12;
+ card->sw_caps.uhs_max_dtr = UHS_SDR12_MAX_DTR;
+ break;
+ default:
+ return 0;
+ }
+
+ err = mmc_sd_switch(card, 1, 0, card->sd_bus_speed, status);
+ if (err)
+ return err;
+
+ if ((status[16] & 0xF) != card->sd_bus_speed)
+ pr_warn("%s: Problem setting bus speed mode!\n",
+ mmc_hostname(card->host));
+ else {
+ mmc_set_timing(card->host, timing);
+ mmc_set_clock(card->host, card->sw_caps.uhs_max_dtr);
+ }
+
+ return 0;
+}
+
+static void sd_update_bus_speed_mode(struct mmc_card *card)
+{
+ /*
+ * If the host doesn't support any of the UHS-I modes, fallback on
+ * default speed.
+ */
+ if (!mmc_host_uhs(card->host)) {
+ card->sd_bus_speed = 0;
+ return;
+ }
+
+ if ((card->host->caps & MMC_CAP_UHS_SDR104) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)) {
+ card->sd_bus_speed = UHS_SDR104_BUS_SPEED;
+ } else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
+ card->sd_bus_speed = UHS_DDR50_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
+ SD_MODE_UHS_SDR50)) {
+ card->sd_bus_speed = UHS_SDR50_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
+ card->sd_bus_speed = UHS_SDR25_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
+ MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
+ SD_MODE_UHS_SDR12)) {
+ card->sd_bus_speed = UHS_SDR12_BUS_SPEED;
+ }
+}
+
+static int mmc_wait_for_app_cmd(struct mmc_host *host, struct mmc_card *card,
+ struct mmc_command *cmd)
+{
+ struct mmc_request mrq = {};
+ int i, err = -EIO;
+
+ /*
+ * We have to resend MMC_APP_CMD for each attempt so
+ * we cannot use the retries field in mmc_command.
+ */
+ for (i = 0; i <= MMC_CMD_RETRIES; i++) {
+ err = mmc_app_cmd(host, card);
+ if (err) {
+ /* no point in retrying; no APP commands allowed */
+ if (mmc_host_is_spi(host)) {
+ if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
+ break;
+ }
+ continue;
+ }
+
+ memset(&mrq, 0, sizeof(struct mmc_request));
+
+ memset(cmd->resp, 0, sizeof(cmd->resp));
+ cmd->retries = 0;
+
+ mrq.cmd = cmd;
+ cmd->data = NULL;
+
+ mmc_wait_for_req(host, &mrq);
+
+ err = cmd->error;
+ if (!cmd->error)
+ break;
+
+ /* no point in retrying illegal APP commands */
+ if (mmc_host_is_spi(host)) {
+ if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
+ break;
+ }
+ }
+
+ return err;
+}
+
+static int mmc_app_set_clr_card_detect(struct mmc_card *card)
+{
+ struct mmc_command cmd = {};
+
+ cmd.opcode = 42;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+
+ return mmc_wait_for_app_cmd(card->host, card, &cmd);
+}
+
+/*
+ * UHS-I specific initialization procedure
+ */
+static int sd_init_uhs_card(struct mmc_card *card)
+{
+ int err;
+ u8 *status;
+
+ if (!(card->csd.cmdclass & CCC_SWITCH))
+ return 0;
+
+ status = kmalloc(64, GFP_KERNEL);
+ if (!status)
+ return -ENOMEM;
+
+ /* Set 4-bit bus width */
+ err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
+ if (err)
+ goto out;
+
+ mmc_set_bus_width(card->host, MMC_BUS_WIDTH_4);
+
+ /*
+ * Select the bus speed mode depending on host
+ * and card capability.
+ */
+ sd_update_bus_speed_mode(card);
+
+ mmc_app_set_clr_card_detect(card);
+
+ /* Set the driver strength for the card */
+ err = sd_select_driver_type(card, status);
+ if (err)
+ goto out;
+
+ /* Set current limit for the card */
+ err = sd_set_current_limit(card, status);
+ if (err)
+ goto out;
+
+ /* Set bus speed mode of the card */
+ err = sd_set_bus_speed_mode(card, status);
+ if (err)
+ goto out;
+
+ /*
+ * SPI mode doesn't define CMD19 and tuning is only valid for SDR50 and
+ * SDR104 mode SD-cards. Note that tuning is mandatory for SDR104.
+ */
+ if (!mmc_host_is_spi(card->host) &&
+ (card->host->ios.timing == MMC_TIMING_UHS_SDR50 ||
+ card->host->ios.timing == MMC_TIMING_UHS_DDR50 ||
+ card->host->ios.timing == MMC_TIMING_UHS_SDR104)) {
+ err = mmc_execute_tuning(card);
+
+ /*
+ * As SD Specifications Part1 Physical Layer Specification
+ * Version 3.01 says, CMD19 tuning is available for unlocked
+ * cards in transfer state of 1.8V signaling mode. The small
+ * difference between v3.00 and 3.01 spec means that CMD19
+ * tuning is also available for DDR50 mode.
+ */
+ if (err && card->host->ios.timing == MMC_TIMING_UHS_DDR50) {
+ pr_warn("%s: ddr50 tuning failed\n",
+ mmc_hostname(card->host));
+ err = 0;
+ }
+ }
+
+out:
+ kfree(status);
+
+ return err;
+}
+
+static bool mmc_sd_card_using_v18(struct mmc_card *card)
+{
+ /*
+ * According to the SD spec., the Bus Speed Mode (function group 1) bits
+ * 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
+ * they can be used to determine if the card has already switched to
+ * 1.8V signaling.
+ */
+ return card->sw_caps.sd3_bus_mode &
+ (SD_MODE_UHS_SDR50 | SD_MODE_UHS_SDR104 | SD_MODE_UHS_DDR50);
+}
+
+/*
+ * Fetches and decodes switch information
+ */
+static int mmc_read_switch(struct mmc_card *card)
+{
+ int err;
+ u8 *status;
+
+ if (card->scr.sda_vsn < SCR_SPEC_VER_1)
+ return 0;
+
+ if (!(card->csd.cmdclass & CCC_SWITCH)) {
+ pr_warn("%s: card lacks mandatory switch function, performance might suffer\n",
+ mmc_hostname(card->host));
+ return 0;
+ }
+
+ status = kmalloc(64, GFP_KERNEL);
+ if (!status)
+ return -ENOMEM;
+
+ /*
+ * Find out the card's support bits with a mode 0 operation.
+ * The argument does not matter, as the support bits do not
+ * change with the arguments.
+ */
+ err = mmc_sd_switch(card, 0, 0, 0, status);
+ if (err) {
+ /*
+ * If the host or the card can't do the switch,
+ * fail more gracefully.
+ */
+ if (err != -EINVAL && err != -ENOSYS && err != -EFAULT)
+ goto out;
+
+ pr_warn("%s: problem reading Bus Speed modes\n",
+ mmc_hostname(card->host));
+ err = 0;
+
+ goto out;
+ }
+
+ if (status[13] & SD_MODE_HIGH_SPEED)
+ card->sw_caps.hs_max_dtr = HIGH_SPEED_MAX_DTR;
+
+ if (card->scr.sda_spec3) {
+ card->sw_caps.sd3_bus_mode = status[13];
+ /* Driver Strengths supported by the card */
+ card->sw_caps.sd3_drv_type = status[9];
+ card->sw_caps.sd3_curr_limit = status[7] | status[6] << 8;
+ }
+
+out:
+ kfree(status);
+
+ return err;
+}
+
+/*
+ * Handle the detection and initialisation of a card.
+ *
+ * In the case of a resume, "oldcard" will contain the card
+ * we're trying to reinitialise.
+ */
+int sd_init_card(struct mmc_host *host, u32 ocr,
+ struct mmc_card *oldcard)
+{
+ struct mmc_card *card;
+ int err;
+ u32 cid[4];
+ u32 rocr = 0;
+ bool v18_fixup_failed = false;
+
+ WARN_ON(!host->claimed);
+retry:
+ err = mmc_sd_get_cid(host, ocr, cid, &rocr);
+ if (err)
+ return err;
+
+ if (oldcard) {
+ if (memcmp(cid, oldcard->raw_cid, sizeof(cid)) != 0) {
+ pr_debug("%s: Perhaps the card was replaced\n",
+ mmc_hostname(host));
+ return -ENOENT;
+ }
+
+ card = oldcard;
+ } else {
+ /*
+ * Allocate card structure.
+ */
+ card = mmc_alloc_card(host, &sd_type);
+ if (IS_ERR(card))
+ return PTR_ERR(card);
+
+ card->ocr = ocr;
+ card->type = MMC_TYPE_SD;
+ memcpy(card->raw_cid, cid, sizeof(card->raw_cid));
+ }
+
+ /*
+ * Call the optional HC's init_card function to handle quirks.
+ */
+ if (host->ops->init_card)
+ host->ops->init_card(host, card);
+
+ /*
+ * For native busses: get card RCA and quit open drain mode.
+ */
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_send_relative_addr(host, &card->rca);
+ if (err)
+ goto free_card;
+ }
+
+ if (!oldcard) {
+ err = mmc_sd_get_csd(host, card);
+ if (err)
+ goto free_card;
+
+ mmc_decode_cid(card);
+ }
+
+ /*
+ * handling only for cards supporting DSR and hosts requesting
+ * DSR configuration
+ */
+ if (card->csd.dsr_imp && host->dsr_req)
+ mmc_set_dsr(host);
+
+ /*
+ * Select card, as all following commands rely on that.
+ */
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_select_card(card);
+ if (err)
+ goto free_card;
+ }
+
+ err = mmc_sd_setup_card(host, card, oldcard != NULL);
+ if (err)
+ goto free_card;
+
+ /*
+ * If the card has not been power cycled, it may still be using 1.8V
+ * signaling. Detect that situation and try to initialize a UHS-I (1.8V)
+ * transfer mode.
+ */
+ if (!v18_fixup_failed && !mmc_host_is_spi(host) && mmc_host_uhs(host) &&
+ mmc_sd_card_using_v18(card) &&
+ host->ios.signal_voltage != MMC_SIGNAL_VOLTAGE_180) {
+ /*
+ * Re-read switch information in case it has changed since
+ * oldcard was initialized.
+ */
+ if (oldcard) {
+ err = mmc_read_switch(card);
+ if (err)
+ goto free_card;
+ }
+ if (mmc_sd_card_using_v18(card)) {
+ if (mmc_host_set_uhs_voltage(host) ||
+ sd_init_uhs_card(card)) {
+ v18_fixup_failed = true;
+ mmc_power_cycle(host, ocr);
+ if (!oldcard)
+ mmc_remove_card(card);
+ goto retry;
+ }
+ goto done;
+ }
+ }
+
+ /* Initialization sequence for UHS-I cards */
+ if (rocr & SD_ROCR_S18A && mmc_host_uhs(host)) {
+ err = sd_init_uhs_card(card);
+ if (err)
+ goto free_card;
+ } else {
+ /*
+ * Switch to wider bus (if supported).
+ */
+ if ((host->caps & MMC_CAP_4_BIT_DATA) &&
+ (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
+ err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
+ if (err)
+ goto free_card;
+
+ mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
+ }
+
+ mmc_app_set_clr_card_detect(card);
+
+ /*
+ * Attempt to change to high-speed (if supported)
+ */
+ err = mmc_sd_switch_hs(card);
+ if (err > 0)
+ mmc_set_timing(card->host, MMC_TIMING_SD_HS);
+ else if (err)
+ goto free_card;
+
+ /*
+ * Set bus speed.
+ */
+ mmc_set_clock(host, mmc_sd_get_max_clock(card));
+ }
+
+ if (host->caps2 & MMC_CAP2_AVOID_3_3V &&
+ host->ios.signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ pr_err("%s: Host failed to negotiate down from 3.3V\n",
+ mmc_hostname(host));
+ err = -EINVAL;
+ goto free_card;
+ }
+done:
+
+ host->card = card;
+ return 0;
+
+free_card:
+ if (!oldcard)
+ mmc_remove_card(card);
+
+ return err;
+}
+
+
+/*
+ * Host is being removed. Free up the current card.
+ */
+static void mmc_sd_remove(struct mmc_host *host)
+{
+ mmc_remove_card(host->card);
+ host->card = NULL;
+}
+
+/*
+ * Card detection - card is alive.
+ */
+static int mmc_sd_alive(struct mmc_host *host)
+{
+ return mmc_send_status(host->card, NULL);
+}
+
+/*
+ * Card detection callback from host.
+ */
+static void mmc_sd_detect(struct mmc_host *host)
+{
+ int err;
+
+ mmc_get_card(host->card, NULL);
+
+ /*
+ * Just check if our card has been removed.
+ */
+ err = _mmc_detect_card_removed(host);
+
+ mmc_put_card(host->card, NULL);
+
+ if (err) {
+ mmc_sd_remove(host);
+
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+ mmc_power_off(host);
+ mmc_release_host(host);
+ }
+}
+
+static int _mmc_sd_suspend(struct mmc_host *host)
+{
+ int err = 0;
+
+ mmc_claim_host(host);
+
+ if (mmc_card_suspended(host->card))
+ goto out;
+
+ if (!mmc_host_is_spi(host))
+ err = mmc_deselect_cards(host);
+
+ if (!err) {
+ mmc_power_off(host);
+ mmc_card_set_suspended(host->card);
+ }
+
+out:
+ mmc_release_host(host);
+ return err;
+}
+
+/*
+ * Callback for suspend
+ */
+static int mmc_sd_suspend(struct mmc_host *host)
+{
+ int err;
+
+ err = _mmc_sd_suspend(host);
+ if (!err) {
+ pm_runtime_disable(&host->card->dev);
+ pm_runtime_set_suspended(&host->card->dev);
+ }
+
+ return err;
+}
+
+/*
+ * This function tries to determine if the same card is still present
+ * and, if so, restore all state to it.
+ */
+static int _mmc_sd_resume(struct mmc_host *host)
+{
+ int err = 0;
+
+ mmc_claim_host(host);
+
+ if (!mmc_card_suspended(host->card))
+ goto out;
+
+ mmc_power_up(host, host->card->ocr);
+ err = sd_init_card(host, host->card->ocr, host->card);
+ mmc_card_clr_suspended(host->card);
+
+out:
+ mmc_release_host(host);
+ return err;
+}
+
+/*
+ * Callback for resume
+ */
+static int mmc_sd_resume(struct mmc_host *host)
+{
+ pm_runtime_enable(&host->card->dev);
+ return 0;
+}
+
+/*
+ * Callback for runtime_suspend.
+ */
+static int mmc_sd_runtime_suspend(struct mmc_host *host)
+{
+ int err;
+
+ if (!(host->caps & MMC_CAP_AGGRESSIVE_PM))
+ return 0;
+
+ err = _mmc_sd_suspend(host);
+ if (err)
+ pr_err("%s: error %d doing aggressive suspend\n",
+ mmc_hostname(host), err);
+
+ return err;
+}
+
+/*
+ * Callback for runtime_resume.
+ */
+static int mmc_sd_runtime_resume(struct mmc_host *host)
+{
+ int err;
+
+ err = _mmc_sd_resume(host);
+ if (err && err != -ENOMEDIUM)
+ pr_err("%s: error %d doing runtime resume\n",
+ mmc_hostname(host), err);
+
+ return 0;
+}
+
+static int mmc_sd_hw_reset(struct mmc_host *host)
+{
+ mmc_power_cycle(host, host->card->ocr);
+ return sd_init_card(host, host->card->ocr, host->card);
+}
+
+static const struct mmc_bus_ops mmc_sd_ops = {
+ .remove = mmc_sd_remove,
+ .detect = mmc_sd_detect,
+ .runtime_suspend = mmc_sd_runtime_suspend,
+ .runtime_resume = mmc_sd_runtime_resume,
+ .suspend = mmc_sd_suspend,
+ .resume = mmc_sd_resume,
+ .alive = mmc_sd_alive,
+ .shutdown = mmc_sd_suspend,
+ .hw_reset = mmc_sd_hw_reset,
+};
+
+/*
+ * Starting point for SD card init.
+ */
+static int attach_sd(struct mmc_host *host)
+{
+ int err;
+ u32 ocr, rocr;
+
+ WARN_ON(!host->claimed);
+
+ err = mmc_send_app_op_cond(host, 0, &ocr);
+ if (err)
+ return err;
+
+ mmc_attach_bus(host, &mmc_sd_ops);
+ if (host->ocr_avail_sd)
+ host->ocr_avail = host->ocr_avail_sd;
+
+ /*
+ * We need to get OCR a different way for SPI.
+ */
+ if (mmc_host_is_spi(host)) {
+ mmc_go_idle(host);
+
+ err = mmc_spi_read_ocr(host, 0, &ocr);
+ if (err)
+ goto err;
+ }
+
+ /*
+ * Some SD cards claims an out of spec VDD voltage range. Let's treat
+ * these bits as being in-valid and especially also bit7.
+ */
+ ocr &= ~0x7FFF;
+
+ rocr = mmc_select_voltage(host, ocr);
+
+ /*
+ * Can we support the voltage(s) of the card(s)?
+ */
+ if (!rocr) {
+ err = -EINVAL;
+ goto err;
+ }
+
+ /*
+ * Detect and init the card.
+ */
+ err = sd_init_card(host, rocr, NULL);
+ if (err)
+ goto err;
+
+ mmc_release_host(host);
+ err = mmc_add_card(host->card);
+ if (err)
+ goto remove_card;
+
+ mmc_claim_host(host);
+ return 0;
+
+remove_card:
+ mmc_remove_card(host->card);
+ host->card = NULL;
+ mmc_claim_host(host);
+err:
+ mmc_detach_bus(host);
+
+ pr_err("%s: error %d whilst initialising SD card\n",
+ mmc_hostname(host), err);
+
+ return err;
+}
+
+static int mmc_schedule_delayed_work(struct delayed_work *work,
+ unsigned long delay)
+{
+ /*
+ * We use the system_freezable_wq, because of two reasons.
+ * First, it allows several works (not the same work item) to be
+ * executed simultaneously. Second, the queue becomes frozen when
+ * userspace becomes frozen during system PM.
+ */
+ return queue_delayed_work(system_freezable_wq, work, delay);
+}
+
+static void mmc_hw_reset_for_init(struct mmc_host *host)
+{
+ mmc_pwrseq_reset(host);
+
+ if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
+ return;
+ host->ops->hw_reset(host);
+}
+
+static int mmc_rescan_try_freq(struct mmc_host *host, unsigned int freq)
+{
+ host->f_init = freq;
+
+ pr_debug("%s: %s: trying to init card at %u Hz\n",
+ mmc_hostname(host), __func__, host->f_init);
+
+ mmc_power_up(host, host->ocr_avail);
+
+ /*
+ * Some eMMCs (with VCCQ always on) may not be reset after power up, so
+ * do a hardware reset if possible.
+ */
+ mmc_hw_reset_for_init(host);
+
+ /*
+ * sdio_reset sends CMD52 to reset card. Since we do not know
+ * if the card is being re-initialized, just send it. CMD52
+ * should be ignored by SD/eMMC cards.
+ * Skip it if we already know that we do not support SDIO commands
+ */
+ if (!(host->caps2 & MMC_CAP2_NO_SDIO))
+ sdio_reset(host);
+
+ mmc_go_idle(host);
+
+ if (!(host->caps2 & MMC_CAP2_NO_SD))
+ mmc_send_if_cond(host, host->ocr_avail);
+
+ /* Order's important: probe SDIO, then SD, then MMC */
+ if (!(host->caps2 & MMC_CAP2_NO_SDIO))
+ if (!mmc_attach_sdio(host))
+ return 0;
+
+ if (!(host->caps2 & MMC_CAP2_NO_SD))
+ if (!attach_sd(host))
+ return 0;
+
+ if (!(host->caps2 & MMC_CAP2_NO_MMC))
+ if (!mmc_attach_mmc(host))
+ return 0;
+
+ mmc_power_off(host);
+ return -EIO;
+}
+
+/*
+ * Cleanup when the last reference to the bus operator is dropped.
+ */
+static void __mmc_release_bus(struct mmc_host *host)
+{
+ WARN_ON(!host->bus_dead);
+
+ host->bus_ops = NULL;
+}
+
+/*
+ * Increase reference count of bus operator
+ */
+static inline void mmc_bus_get(struct mmc_host *host)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->bus_refs++;
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+/*
+ * Decrease reference count of bus operator and free it if
+ * it is the last reference.
+ */
+static inline void mmc_bus_put(struct mmc_host *host)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->bus_refs--;
+ if ((host->bus_refs == 0) && host->bus_ops)
+ __mmc_release_bus(host);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+void mmc_rescan_bayhub(struct work_struct *work)
+{
+ struct mmc_host *host =
+ container_of(work, struct mmc_host, detect.work);
+ int i;
+
+ if (host->rescan_disable)
+ return;
+
+ /* If there is a non-removable card registered, only scan once */
+ if (!mmc_card_is_removable(host) && host->rescan_entered)
+ return;
+ host->rescan_entered = 1;
+
+ if (host->trigger_card_event && host->ops->card_event) {
+ mmc_claim_host(host);
+ host->ops->card_event(host);
+ mmc_release_host(host);
+ host->trigger_card_event = false;
+ }
+
+ mmc_bus_get(host);
+
+ /* Verify a registered card to be functional, else remove it. */
+ if (host->bus_ops && !host->bus_dead)
+ host->bus_ops->detect(host);
+
+ host->detect_change = 0;
+
+ /*
+ * Let mmc_bus_put() free the bus/bus_ops if we've found that
+ * the card is no longer present.
+ */
+ mmc_bus_put(host);
+ mmc_bus_get(host);
+
+ /* if there still is a card present, stop here */
+ if (host->bus_ops != NULL) {
+ mmc_bus_put(host);
+ goto out;
+ }
+
+ /*
+ * Only we can add a new handler, so it's safe to
+ * release the lock here.
+ */
+ mmc_bus_put(host);
+
+ mmc_claim_host(host);
+ if (mmc_card_is_removable(host) && host->ops->get_cd &&
+ host->ops->get_cd(host) == 0) {
+ mmc_power_off(host);
+ mmc_release_host(host);
+ goto out;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(freqs); i++) {
+ if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
+ break;
+ if (freqs[i] <= host->f_min)
+ break;
+ }
+ mmc_release_host(host);
+
+ out:
+ if (host->caps & MMC_CAP_NEEDS_POLL)
+ mmc_schedule_delayed_work(&host->detect, HZ);
+}
+
+static int card_deselect_card(struct sdhci_host *host)
+{
+ int ret = -1;
+ int err;
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_command cmd = { 0 };
+
+ cmd.opcode = MMC_SELECT_CARD;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+
+ err = mmc_wait_for_cmd(mmc, &cmd, 3);
+ if (err)
+ pr_err("BHT ERR: CMD7 FAIL: err = %d\n", err);
+ else
+ ret = 0;
+
+ return ret;
+}
+
+static bool enter_exit_emulator_mode(struct sdhci_host *host, bool b_enter)
+{
+ bool ret = FALSE;
+ u8 times = b_enter ? 2 : 1;
+ u8 i = 0;
+
+ for (i = 0; i < times; i++) {
+ ret = card_deselect_card(host);
+ if (ret)
+ break;
+ }
+ return ret;
+}
+
+static bool _gg_emulator_read_only(struct sdhci_host *host,
+ u8 *in_data, u32 datalen)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int rc = 0;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+ struct mmc_request mrq = { 0 };
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+
+ if (!data1) {
+ pr_err("BHT MSG:gg read no memory\n");
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_READ_SINGLE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_READ;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+ memcpy(in_data, data1, datalen);
+
+ kfree(data1);
+
+ if ((cmd.error == -EILSEQ) || (data.error == -EILSEQ))
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+
+ if (cmd.error || data.error)
+ rc = -1;
+out:
+ return rc;
+}
+
+static void host_cmddat_line_reset(struct sdhci_host *host)
+{
+ if (host->ops->reset)
+ host->ops->reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
+}
+
+static int gg_select_card_spec(struct sdhci_host *host)
+{
+ int err;
+ struct mmc_command cmd = { 0 };
+ struct mmc_card *card = host->mmc->card;
+
+ cmd.opcode = MMC_SELECT_CARD;
+
+ if (card) {
+ cmd.arg = card->rca << 16;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+ } else {
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+ }
+
+ err = mmc_wait_for_cmd(host->mmc, &cmd, 0);
+ if (err == -EILSEQ) {
+ host_cmddat_line_reset(host);
+
+ memset(&cmd, 0, sizeof(struct mmc_command));
+ cmd.opcode = 5;
+ cmd.arg = 0;
+ cmd.flags =
+ MMC_RSP_SPI_R4 | MMC_RSP_R4 | MMC_CMD_BCR;
+
+ mmc_wait_for_cmd(host->mmc, &cmd, 0);
+
+ pr_err("BHT ERR:%s: CMD7 CRC\n", __func__);
+ host_cmddat_line_reset(host);
+ return 0;
+ }
+ if (err == -ETIMEDOUT) {
+ pr_err("BHT ERR:%s: CMD7 timeout\n", __func__);
+ host_cmddat_line_reset(host);
+ return err;
+ }
+ return 0;
+}
+
+static bool gg_emulator_read_ext(struct sdhci_host *host, bool *card_status,
+ bool *read_status, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool card_ret = TRUE;
+ bool rd_ret = FALSE;
+
+ if (enter_exit_emulator_mode(host, TRUE) == 0)
+ ret = TRUE;
+ else
+ ret = FALSE;
+ if (!ret)
+ goto exit;
+
+ if (_gg_emulator_read_only(host, data, datalen) == 0)
+ rd_ret = TRUE;
+ else
+ rd_ret = FALSE;
+
+ if (enter_exit_emulator_mode(host, FALSE) == 0)
+ ret = TRUE;
+ else
+ ret = FALSE;
+
+ if (!ret)
+ goto exit;
+
+ if (gg_select_card_spec(host) == 0)
+ card_ret = TRUE;
+ else
+ card_ret = FALSE;
+
+ if (!rd_ret)
+ pr_err("BHT ERR:GGC read status error\n");
+
+exit:
+ if (!card_ret) {
+ pr_err("BHT ERR:GGC Emulator exit Fail!!\n");
+ ret = FALSE;
+ }
+
+ if (card_status)
+ *card_status = ret;
+
+ if (read_status)
+ *read_status = rd_ret;
+
+ if (rd_ret && !ret)
+ pr_err("BHT ERR:data read ok, but exit NG\n");
+ else if (!rd_ret && ret)
+ pr_err("BHT ERR:data read NG, but exit ok\n");
+
+ return ret;
+}
+
+static void _status_bit_2_bt(int tar, int *byt, int *bit)
+{
+ *byt = tar / 8;
+ *bit = tar % 8;
+}
+
+static u32 _read_status_data_read_register(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ _status_bit_2_bt(bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+ return rv;
+}
+
+static bool ggc_read_registers_ext(struct sdhci_host *host,
+ bool *card_status, bool *read_status,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num)
+{
+ u8 get_idx = 0;
+ bool ret = FALSE;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+
+ if (read_status)
+ *read_status = FALSE;
+ if (card_status)
+ *card_status = FALSE;
+
+ memset(ggc->_cur_read_buf, 0, 512);
+ ret = gg_emulator_read_ext(host, card_status, read_status, ggc->_cur_read_buf, 512);
+ if (read_status == FALSE)
+ goto exit;
+
+ for (get_idx = 0; get_idx < num; get_idx++)
+ (gg_reg_arr + get_idx)->value =
+ _read_status_data_read_register(ggc->_cur_read_buf, (gg_reg_arr + get_idx));
+
+exit:
+ return ret;
+}
+
+static bool gg_emulator_read(struct sdhci_host *host, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool rd_ret = FALSE;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ rd_ret = _gg_emulator_read_only(host, data, datalen);
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = gg_select_card_spec(host);
+
+exit:
+ if (rd_ret)
+ pr_err("BHT ERR:GGC read status error\n");
+
+ if (ret)
+ pr_err("BHT ERR:GGC Emulator exit Fail!!\n");
+
+ if (rd_ret == 0 && ret) {
+ pr_err("BHT ERR:data read ok, but exit NG\n");
+ ret = 0;
+ }
+
+ if (rd_ret && ret == 0) {
+ pr_err("BHT ERR:data read NG, but exit ok\n");
+ ret = -1;
+ }
+
+ return ret ? FALSE : TRUE;
+}
+
+static bool _ggc_emulator_write_only(struct sdhci_host *host,
+ u8 *in_data, u32 datalen)
+{
+ struct mmc_host *mmc = host->mmc;
+ int rc = 0;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+ struct mmc_request mrq = { 0 };
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!data1) {
+ pr_err("BHT MSG:gg write no memory\n");
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ memcpy(data1, in_data, datalen);
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_WRITE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_WRITE;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+
+ if (cmd.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+
+ kfree(data1);
+out:
+ return rc;
+}
+
+static bool gg_emulator_write(struct sdhci_host *host, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool wr_ret = FALSE;
+ u32 i = 0;
+ u32 reg;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ pr_debug("BHT MSG: dump config data\n");
+ for (i = 0; i < (datalen/sizeof(u32)); i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("BHT MSG:\tggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+
+ _ggc_emulator_write_only(host, data, datalen);
+ wr_ret = TRUE;
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = gg_select_card_spec(host);
+
+exit:
+ if (wr_ret == FALSE)
+ ret = FALSE;
+
+ if (ret == FALSE)
+ pr_err("BHT ERR:%s: GGC Emulator Write Fail!!\n", __func__);
+
+ return ret;
+}
+
+static bool get_gg_reg_cur(struct sdhci_host *host, u8 *data,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num)
+{
+ u8 get_idx = 0;
+ bool ret = FALSE;
+
+ /* read ggc register */
+ memset(data, 0, 512);
+ ret = gg_emulator_read(host, data, 512);
+
+ if (ret == FALSE)
+ goto exit;
+
+ /* read the offset bits value */
+ for (get_idx = 0; get_idx < num; get_idx++) {
+ (gg_reg_arr + get_idx)->value =
+ read_ram_bits_ofs_mask(data, (gg_reg_arr + get_idx));
+ }
+exit:
+ return ret;
+}
+
+static void chg_gg_reg_cur_val(struct ggc_platform_t *ggc, u8 *data,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num, bool b_sav_chg)
+{
+ u8 chg_idx = 0;
+
+ for (chg_idx = 0; chg_idx < num; chg_idx++) {
+ /* modify the ggc register bit value */
+ cfg_write_bits_ofs_mask(data, (gg_reg_arr + chg_idx),
+ (gg_reg_arr + chg_idx)->value);
+ }
+
+ if (b_sav_chg)
+ set_gg_reg_cur_val(ggc, data, 64);
+}
+
+static void log_bin(u32 n)
+{
+ int i = 0;
+ u8 tb[33] = { 0 };
+
+ for (i = 0; i < 32; i++) {
+ if (n & (1 << i))
+ tb[i] = '1';
+ else
+ tb[i] = '0';
+ }
+ pr_debug("BHT MSG:bin:%s\n", tb);
+}
+
+static void phase_str(u8 *tb, u32 n)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (n & (1 << i))
+ tb[i] = '1';
+ else
+ tb[i] = '0';
+ }
+ tb[TUNING_PHASE_SIZE] = 0;
+}
+
+static int get_bit_number(u32 n)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (n & (1 << i))
+ cnt++;
+ }
+ return cnt;
+}
+
+static bool gg_emulator_write_ext(struct sdhci_host *host, bool *card_status, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool wr_ret = FALSE;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ _ggc_emulator_write_only(host, data, datalen);
+ wr_ret = TRUE;
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = (gg_select_card_spec(host) == 0) ? TRUE : FALSE;
+ if (ret == FALSE) {
+ if (card_status)
+ *card_status = FALSE;
+ }
+
+exit:
+ if (wr_ret == FALSE)
+ ret = FALSE;
+
+ if (ret == FALSE)
+ pr_err("BHT ERR:%s: GGC Emulator Write Fail!!\n", __func__);
+
+ return ret;
+}
+
+static bool ggc_set_output_tuning_phase_ext(struct sdhci_host *host,
+ bool *card_status, int sela, int selb)
+{
+ bool ret = TRUE;
+ u8 data[512] = { 0 };
+ struct t_gg_reg_strt gg_reg_arr[8];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_sela_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_sela_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_selb_100m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_200m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.internl_tuning_en_100m,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.internl_tuning_en_200m,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = sela;
+ gg_reg_arr[1].value = sela;
+ gg_reg_arr[2].value = selb;
+ gg_reg_arr[3].value = selb;
+ gg_reg_arr[4].value = 1;
+ gg_reg_arr[5].value = 1;
+ gg_reg_arr[6].value = 1;
+ gg_reg_arr[7].value = 1;
+ if (card_status)
+ *card_status = TRUE;
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 8, TRUE);
+ ret = gg_emulator_write_ext(host, card_status, data, 512);
+ return ret;
+}
+
+static bool gg_fix_output_tuning_phase(struct sdhci_host *host, int sela, int selb)
+{
+ u8 data[512] = { 0 };
+ struct t_gg_reg_strt gg_reg_arr[10];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("BHT MSG: %s - sela dll: %x, selb dll: %x\n", __func__, sela,
+ selb);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_sela_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_sela_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_selb_100m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_200m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.internl_tuning_en_100m,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.internl_tuning_en_200m,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = sela;
+ gg_reg_arr[1].value = sela;
+ gg_reg_arr[2].value = selb;
+ gg_reg_arr[3].value = selb;
+ gg_reg_arr[4].value = 1;
+ gg_reg_arr[5].value = 1;
+ gg_reg_arr[6].value = 0;
+ gg_reg_arr[7].value = 0;
+
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 8, TRUE);
+
+ return gg_emulator_write(host, data, 512);
+}
+
+static void gen_array_data(u32 low32, u32 high32, u32 *ptw)
+{
+ u8 tu_res_per[6][TUNING_PHASE_SIZE];
+ u8 i = 0, j = 0;
+ u8 i_mode = 0;
+ u32 tw = 0;
+
+ memset(tu_res_per, 1, sizeof(tu_res_per));
+ for (i = 0; i < 64; i++) {
+ u32 tmp_data = (i < 32) ? low32 : high32;
+
+ tu_res_per[i / TUNING_PHASE_SIZE][i % TUNING_PHASE_SIZE] =
+ (tmp_data & (1 << (i % 32))) >> (i % 32);
+ }
+
+ for (i_mode = 0; i_mode < TUNING_PHASE_SIZE; i_mode++) {
+ for (j = 0; j < 6; j++) {
+ if (tu_res_per[j][i_mode] != 0)
+ tw |= (1 << i_mode);
+ else {
+ tw &= ~(1 << i_mode);
+ break;
+ }
+ }
+ }
+ if (ptw)
+ *ptw = tw;
+}
+
+static bool sw_calc_tuning_result(struct sdhci_host *host, u32 *tx_selb,
+ u32 *all_selb, u64 *raw_tx_selb)
+{
+ bool ret = FALSE;
+ u8 data[512] = { 0 };
+ u32 selb_status_tx_low32 = 0, selb_status_tx_high32 = 0;
+ u32 selb_status_ggc_low32 = 0, selb_status_ggc_high32 = 0;
+ struct t_gg_reg_strt gg_reg_arr[6];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.pha_stas_tx_low32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.pha_stas_tx_high32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.pha_stas_rx_low32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.pha_stas_rx_high32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_sela_after_mask, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_after_mask, sizeof(struct t_gg_reg_strt));
+
+ ret = get_gg_reg_cur(host, data, gg_reg_arr, 6);
+
+ if (ret == TRUE) {
+ selb_status_tx_low32 = gg_reg_arr[0].value;
+ pr_debug("BHT MSG:[205-236]:\n");
+ log_bin(selb_status_tx_low32);
+ selb_status_tx_high32 = gg_reg_arr[1].value;
+ pr_debug("BHT MSG:[237-268]:\n");
+ log_bin(selb_status_tx_high32);
+ selb_status_ggc_low32 = gg_reg_arr[2].value;
+ pr_debug("BHT MSG:[14-45]:\n");
+ log_bin(selb_status_ggc_low32);
+ selb_status_ggc_high32 = gg_reg_arr[3].value;
+ pr_debug("BHT MSG:[46-77]:\n");
+ log_bin(selb_status_ggc_high32);
+ pr_debug("BHT MSG:dll sela after mask=%xh\n", gg_reg_arr[4].value);
+ pr_debug("BHT MSG:dll selb after mask=%xh\n", gg_reg_arr[5].value);
+
+ if (raw_tx_selb) {
+ *raw_tx_selb = gg_reg_arr[1].value;
+ (*raw_tx_selb) <<= 32;
+ *raw_tx_selb += gg_reg_arr[0].value;
+ pr_debug("BHT MSG:raw_tx_selb:%llxh\n", *raw_tx_selb);
+ }
+
+ if (tx_selb) {
+ gen_array_data(gg_reg_arr[0].value, gg_reg_arr[1].value,
+ tx_selb);
+ pr_debug("BHT MSG:tx_selb:%xh\n", *tx_selb);
+ }
+ if (all_selb) {
+ gen_array_data(gg_reg_arr[2].value, gg_reg_arr[3].value,
+ all_selb);
+ pr_debug("BHT MSG:all_selb:%xh\n", *all_selb);
+ }
+ }
+
+ return ret;
+}
+
+static bool gg_tuning_result(struct sdhci_host *host, u32 *tx_selb, u32 *all_selb,
+ u64 *raw_tx_selb)
+{
+ host_cmddat_line_reset(host);
+ return sw_calc_tuning_result(host, tx_selb, all_selb, raw_tx_selb);
+}
+
+static u64 GENERATE_64_IDX_VALUE(int sft)
+{
+ u64 val = 1;
+
+ return val << sft;
+}
+
+static bool is_bus_mode_sdr104(struct sdhci_host *host)
+{
+ bool ret = FALSE;
+
+ if (host->timing == MMC_TIMING_UHS_SDR104)
+ ret = TRUE;
+
+ return ret;
+}
+
+static bool _check_bus_mode(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+
+ if (is_bus_mode_sdr104(host))
+ ggc->cur_bus_mode = &vendor_host->ggc.sdr104;
+ else
+ ggc->cur_bus_mode = &vendor_host->ggc.sdr50;
+
+ return true;
+}
+
+static void tx_selb_failed_history_update(struct sdhci_host *host, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+
+ vendor_host->ggc.cur_bus_mode->tx_selb_failed_history &= val;
+}
+
+static u32 tx_selb_failed_history_get(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+
+ return vendor_host->ggc.cur_bus_mode->tx_selb_failed_history;
+}
+
+static void tx_selb_failed_tb_update(struct sdhci_host *host, int sela, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+ vendor_host->ggc.cur_bus_mode->tx_selb_tb[sela] &= val;
+}
+
+static u32 tx_selb_failed_tb_get(struct sdhci_host *host, int sela)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 value = 0;
+
+ _check_bus_mode(host);
+
+ if (is_bus_mode_sdr104(host))
+ value = vendor_host->ggc.sdr104.tx_selb_tb[sela];
+ else
+ value = vendor_host->ggc.sdr50.tx_selb_tb[sela];
+
+ return value;
+}
+
+static void all_selb_failed_tb_update(struct sdhci_host *host, int sela, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+ vendor_host->ggc.cur_bus_mode->all_selb_tb[sela] &= val;
+}
+
+static u32 all_selb_failed_tb_get(struct sdhci_host *host, int sela)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 val;
+
+ _check_bus_mode(host);
+
+ val = vendor_host->ggc.cur_bus_mode->all_selb_tb[sela];
+
+ return val;
+}
+
+static void chk_phase_window(u8 *tuning_win, u8 *mid_val, u8 *max_pass_win)
+{
+ u8 tuning_pass[TUNING_PHASE_SIZE + 32];
+ u8 tuning_pass_start[TUNING_PHASE_SIZE + 32];
+ u8 tuning_pass_num_max = 0;
+ u8 first_0 = 0;
+ u8 i = 0, j = 0;
+ u8 i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 1, sizeof(tuning_pass));
+ memset(tuning_pass_start, 1, sizeof(tuning_pass_start));
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = (first_0 + i) % TUNING_PHASE_SIZE;
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0)
+ pr_err
+ ("Get max pass window fail, there is no any pass phase!!\n");
+ else {
+ *max_pass_win = tuning_pass_num_max - 1;
+ tuning_pass_num_max /= 2;
+ selb_mode = tuning_pass_start[i_mode] + tuning_pass_num_max;
+ if ((*max_pass_win % 2 == 0))
+ selb_mode += 1;
+ selb_mode %= TUNING_PHASE_SIZE;
+ }
+
+ *mid_val = selb_mode;
+}
+
+static void dump_array(u8 *tb)
+{
+ int i = 0;
+ u8 str[12] = { 0 };
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ str[i] = tb[i] + '0';
+}
+
+static void bits_generate_array(u8 *tb, u32 v)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if ((v & (1 << i)))
+ tb[i] = 1;
+ else
+ tb[i] = 0;
+ }
+ dump_array(tb);
+}
+
+static void chk_arr_max_win(u8 *tuning_win, u8 first_i, u8 *mid_val,
+ u8 *first_val, u8 *max_pass_win, struct chk_type_t type)
+{
+ u8 tuning_pass[TUNING_PHASE_SIZE];
+ u8 tuning_pass_start[TUNING_PHASE_SIZE];
+ u8 tuning_pass_num_max = 0;
+ u8 first_0 = 0;
+ u8 i = 0, j = 0;
+ u8 i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 1, sizeof(tuning_pass));
+ memset(tuning_pass_start, 1, sizeof(tuning_pass_start));
+
+ if (type.first_valid)
+ first_0 = first_i;
+ else {
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = (first_0 + i) % TUNING_PHASE_SIZE;
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0)
+ pr_err
+ ("Get max pass window fail, there is no any pass phase!!\n");
+ else {
+ *max_pass_win = tuning_pass_num_max - 1;
+ tuning_pass_num_max /= 2;
+ if (first_val)
+ *first_val = tuning_pass_start[i_mode];
+ selb_mode = tuning_pass_start[i_mode] + tuning_pass_num_max;
+ if ((*max_pass_win % 2 == 0) && (type.right_valid)
+ )
+ selb_mode += 1;
+ selb_mode %= TUNING_PHASE_SIZE;
+ }
+
+ *mid_val = selb_mode;
+}
+
+void no_fail_p(u8 *tuning_win, u8 *mid_val, u8 *max_pass_win, u8 *first_val)
+{
+ struct chk_type_t type;
+ u8 first_0 = 0;
+
+ memset((u8 *)&type, 0, sizeof(struct chk_type_t));
+
+ type.first_valid = 0;
+ type.right_valid = 1;
+ type.record_valid = 0;
+
+ chk_arr_max_win(tuning_win, first_0, mid_val, first_val,
+ max_pass_win, type);
+}
+
+static int ggc_get_selx_weight(u32 val)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i))
+ cnt++;
+ }
+ return cnt;
+}
+
+void tx_selb_calculate_valid_phase_range(u32 val, int *start,
+ int *pass_cnt)
+{
+ int i = 0, flg = 0;
+
+ *pass_cnt = ggc_get_selx_weight(val);
+ for (i = 0; i < (TUNING_PHASE_SIZE * 2); i++) {
+ if ((GET_TRUNING_RING_IDX_VALUE(val, i)) == 0 && (flg == 0))
+ flg = 1;
+ if ((flg == 1) && GET_TRUNING_RING_IDX_VALUE(val, i)) {
+ *start = TRUNING_RING_IDX(i);
+ break;
+ }
+ }
+}
+
+bool ggc_update_default_selb_phase_tuning_cnt(struct sdhci_host *host, int selb,
+ int tuning_cnt)
+{
+ struct t_gg_reg_strt gg_reg_arr[3];
+ u8 data[512];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+
+ pr_debug("BHT MSG: selb:%xh,tuning_cnt:%xh\n", selb,
+ tuning_cnt);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.cmd19_cnt_cfg,
+ sizeof(struct t_gg_reg_strt));
+
+ gg_reg_arr[0].value = selb;
+ gg_reg_arr[1].value = selb;
+ gg_reg_arr[2].value = tuning_cnt;
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 3, TRUE);
+
+ return TRUE;
+}
+
+static void _ggc_update_cur_setting_for_sw_selb_tuning(struct sdhci_host *host,
+ u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int start = 0, pass_cnt = 0;
+
+ tx_selb_calculate_valid_phase_range(val, &start, &pass_cnt);
+ pr_debug("BHT MSG:%s %x %x %x\n", __func__, val, start, pass_cnt);
+ ggc_update_default_selb_phase_tuning_cnt(host, start, pass_cnt); //update
+ vendor_host->ggc.ggc_sw_selb_tuning_first_selb = start;
+}
+
+int sdhci_bht_sdr50_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+
+ u8 phase, *data_buf;
+ int size = 64;
+ int rc = 0;
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__);
+
+ data_buf = kmalloc(size, GFP_KERNEL);
+
+ phase = 0;
+ do {
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct mmc_request mrq = {
+ .cmd = &cmd,
+ .data = &data
+ };
+ struct scatterlist sg;
+
+ cmd.opcode = opcode;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+
+ data.blksz = size;
+ data.blocks = 1;
+ data.flags = MMC_DATA_READ;
+ data.timeout_ns = 30 * 1000 * 1000; /* 30ms */
+
+ data.sg = &sg;
+ data.sg_len = 1;
+ sg_init_one(&sg, data_buf, size);
+ memset(data_buf, 0, size);
+ host_cmddat_line_reset(host);
+ mmc_wait_for_req(mmc, &mrq);
+
+ if (cmd.error) {
+ if (cmd.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+ if (cmd.error == -ETIMEDOUT && phase == 0) {
+ pr_err("BHT ERR:cmd19 timeout\n");
+ rc = -ETIMEDOUT;
+ goto kfree;
+ }
+ }
+
+ if (data.error) {
+ if (data.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+ }
+ } while (++phase < 16);
+
+kfree:
+ kfree(data_buf);
+
+ return rc;
+}
+
+int get_config_sela_setting(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (is_bus_mode_sdr104(host))
+ return vendor_host->ggc.def_sela_200m;
+ else
+ return vendor_host->ggc.def_sela_100m;
+}
+
+int get_config_selb_setting(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (is_bus_mode_sdr104(host))
+ return vendor_host->ggc.def_selb_200m;
+ else
+ return vendor_host->ggc.def_selb_100m;
+}
+
+u32 get_all_sela_status(struct sdhci_host *host, u32 target_selb)
+{
+ u32 all_sela = 0;
+ u32 all_selb = 0;
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ all_selb = all_selb_failed_tb_get(host, i);
+ if (all_selb & (1 << target_selb))
+ all_sela |= 1 << i;
+ }
+ return all_sela;
+}
+
+int get_pass_window_weight(u32 val)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i))
+ cnt++;
+ }
+ return cnt;
+}
+
+int get_sela_nearby_pass_window(u32 sela, u32 base)
+{
+
+ int i = 0;
+ int idx = base;
+ int cnt = 0;
+
+ if (GET_IDX_VALUE(sela, idx) == 0)
+ return 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(sela, idx)) {
+ idx++;
+ idx %= TUNING_PHASE_SIZE;
+ } else {
+ break;
+ }
+ }
+
+ if (idx == 0)
+ idx = 0xa;
+ else
+ idx--;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(sela, idx)) {
+ cnt++;
+ if (idx == 0)
+ idx = 0xa;
+ else
+ idx--;
+ } else {
+ break;
+ }
+ }
+ return cnt;
+}
+
+int get_left_one_sel(int base)
+{
+ if (base == 0)
+ return 0xa;
+ else
+ return base - 1;
+}
+
+int get_right_one_sel(int base)
+{
+ if (base == 0xa)
+ return 0x0;
+ else
+ return base + 1;
+}
+
+int get_dif(int x, int y)
+{
+ int dif = 0;
+
+ if (y > x)
+ dif = y - x;
+ else
+ dif = x - y;
+
+ return dif;
+}
+
+static int update_selb(struct sdhci_host *host, int target_selb)
+{
+ return target_selb;
+}
+
+static int ggc_get_10case_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val,
+ TRUNING_RING_IDX(i + TUNING_PHASE_SIZE -
+ 1))) {
+ return i;
+ }
+ }
+
+ return -1;
+}
+
+static u32 ggc_get_01case_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val, TRUNING_RING_IDX(i + 1))) {
+ return i;
+ }
+ }
+
+ return -1;
+}
+
+static int ggc_get_next_1_index(u32 val, int pos)
+{
+ int i = 0;
+
+ pos = pos % TUNING_PHASE_SIZE;
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, (pos+i)%TUNING_PHASE_SIZE))
+ break;
+ }
+ if (GET_IDX_VALUE(val, (pos+i)%TUNING_PHASE_SIZE))
+ return (pos+i)%TUNING_PHASE_SIZE;
+ else
+ return -1;
+}
+
+static u32 ggc_get_01case_1_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val, TRUNING_RING_IDX(i + 1))) {
+ return TRUNING_RING_IDX(i + 1);
+ }
+ }
+
+ return -1;
+}
+
+static int ggc_get_first_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0)
+ return i;
+ }
+ pr_debug("BHT MSG:oops-not find 0 index\n");
+ return 0;
+}
+
+static int _tx_selb_inject_policy(int tx_selb, int org_selb)
+{
+ int group_pos[TUNING_PHASE_SIZE+1][3];
+ int group_cnt = 0;
+ int max_len_group = 0;
+ int max_len = 0;
+ int i, j, cnt;
+ int zero_start, zero_end, sel;
+
+ if ((org_selb & BIT_PASS_MASK) != BIT_PASS_MASK) {
+ sel = tx_selb;
+ zero_start = ggc_get_10case_0_index(sel);
+ sel &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (zero_start));
+ zero_end = ggc_get_01case_0_index(sel);
+ sel &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (zero_end));
+ if (sel != (sel & tx_selb)) {
+ pr_err
+ ("tx selb reinject exception case :not adjacent phase\n");
+ pr_err("BHT ERR:selb_failed range:%xh ,new tx_selb:%x\n",
+ org_selb, tx_selb);
+ }
+ org_selb &= tx_selb;
+ } else {
+ cnt = ggc_get_selx_weight(~tx_selb);
+ pr_debug("BHT MSG:%d\n", cnt);
+ switch (cnt) {
+ case 1:
+ i = ggc_get_first_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (i));
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (i));
+
+ break;
+ case 2:
+ i = ggc_get_10case_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (i));
+ i = ggc_get_01case_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (i));
+ break;
+ default:
+ pr_debug("BHT MSG:>= 3 point case\n");
+ }
+ org_selb &= tx_selb;
+ }
+
+ pr_debug("BHT MSG:will check continuous 0bits: 0x%x\n", org_selb);
+
+ memset(group_pos, 0, sizeof(group_pos));
+ for (i = ggc_get_01case_1_index(org_selb);
+ i < TUNING_PHASE_SIZE && i >= 0 && group_cnt < TUNING_PHASE_SIZE;) {
+ for (j = 1; j < TUNING_PHASE_SIZE; j++) {
+ if (GET_TRUNING_RING_IDX_VALUE(org_selb, i+j) != 0)
+ continue;
+ else
+ break;
+ }
+ group_pos[group_cnt][0] = i;
+ group_pos[group_cnt][1] = (i + j - 1) % TUNING_PHASE_SIZE;
+ group_pos[group_cnt][2] = j;
+ group_cnt++;
+ if (group_pos[group_cnt-1][0] > group_pos[group_cnt-1][1])
+ break;
+ i = ggc_get_next_1_index(org_selb, (i+j)%TUNING_PHASE_SIZE);
+ for (j = 0; j < group_cnt; j++) {
+ if (i == group_pos[j][0])
+ break;
+ }
+ if (j < group_cnt)
+ break;
+ }
+
+ if (group_cnt > 1) {
+ pr_err("BHT ERR:After inject, selb 0x%x has %d continuous 0 bits\n",
+ org_selb, group_cnt);
+
+ for (i = 0; i < group_cnt; i++) {
+ if (max_len < group_pos[i][2]) {
+ max_len = group_pos[i][2];
+ max_len_group = i;
+ }
+ }
+ for (i = (group_pos[max_len_group][1] + 1) % TUNING_PHASE_SIZE;
+ i != group_pos[max_len_group][0]; i = (i+1)%TUNING_PHASE_SIZE) {
+ org_selb &= ~(1 << i);
+ }
+ pr_err("BHT ERR:After merge incontious 0 group, selb changed to 0x%x\n", org_selb);
+ } else if (group_cnt > 0) {
+ pr_err("BHT ERR:After merge incontious 0 group, selb = 0x%x\n", org_selb);
+ } else {
+ pr_err("BHT ERR:selb 0x%x has no bit is 0\n", org_selb);
+ }
+
+ return org_selb;
+}
+
+void tx_selb_inject_policy(struct sdhci_host *host, int tx_selb)
+{
+
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("BHT MSG:before inject, failed ragen 0x%x, tx_selb 0x%x\n",
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, tx_selb);
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range =
+ _tx_selb_inject_policy(tx_selb, vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ tx_selb_failed_history_update(host, vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ pr_debug("BHT MSG:after inject %xh range:%xh\n", tx_selb,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ if (is_bus_mode_sdr104(host))
+ vendor_host->ggc.sdr104.fail_phase = vendor_host->ggc.ggc_cmd_tx_selb_failed_range;
+ else
+ vendor_host->ggc.sdr50.fail_phase = vendor_host->ggc.ggc_cmd_tx_selb_failed_range;
+}
+
+int get_selb_failure_point(int start, u64 raw_tx_selb, int tuning_cnt)
+{
+ int last = start + (tuning_cnt - 1);
+ int i = 0;
+ int j = 0;
+ int phase = start;
+ int vct = BIT_PASS_MASK;
+
+ pr_debug("BHT MSG:%s start:%d tuning_cnt:%d\n", __func__, start,
+ tuning_cnt);
+
+ for (i = 0; i < tuning_cnt; i++) {
+ if ((raw_tx_selb & GENERATE_64_IDX_VALUE(last - i)) == 0)
+ break;
+ }
+ if (i == tuning_cnt) {
+ phase = last % TUNING_PHASE_SIZE;
+ vct &= (~(1 << phase));
+ goto exit;
+ }
+
+ for (i = 0; i < tuning_cnt; i++) {
+ if ((raw_tx_selb & GENERATE_64_IDX_VALUE(last - i)) != 0)
+ break;
+ }
+ for (j = i - 2; j >= 0; j--)
+ raw_tx_selb |= (1 << (last - j));
+
+ for (j = 0; j < tuning_cnt; j++) {
+ if (0 == (raw_tx_selb & GENERATE_64_IDX_VALUE(last - j)))
+ vct &= (~(1 << (last-j)));
+ }
+
+exit:
+ pr_debug("BHT MSG:%s: after adjust raw_tx_selb: 0x%llx, vct 0x%x\n",
+ __func__, raw_tx_selb, vct);
+
+ return vct;
+}
+
+bool selx_failure_point_exist(u32 val)
+{
+ return (val & BIT_PASS_MASK) != BIT_PASS_MASK;
+}
+
+static int _bits_vct_get_left_index(int base)
+{
+ return TRUNING_RING_IDX(base + TUNING_PHASE_SIZE - 1);
+}
+
+int _get_best_window_phase(u32 vct, int *pmax_pass_win, int shif_left_flg)
+{
+ u8 tuning_win[TUNING_PHASE_SIZE] = { 0 };
+ u8 tuning_pass[TUNING_PHASE_SIZE];
+ int tuning_pass_start[TUNING_PHASE_SIZE];
+ int tuning_pass_num_max = 0;
+ int first_0 = 0;
+ int i = 0, j = 0;
+ int i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 0, sizeof(tuning_pass));
+ memset(tuning_pass_start, 0, sizeof(tuning_pass_start));
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(vct, i))
+ tuning_win[i] = 1;
+ else
+ tuning_win[i] = 0;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = TRUNING_RING_IDX(first_0 + i);
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0) {
+ pr_err("BHT ERR:###### Get max pass window fail, there is no any pass phase!!\n");
+ selb_mode = 0;
+ } else {
+ if (tuning_pass_num_max % 2) {
+ selb_mode = tuning_pass_start[i_mode] + (tuning_pass_num_max - 1) / 2;
+ } else {
+ selb_mode = tuning_pass_start[i_mode] + (tuning_pass_num_max) / 2;
+ if (shif_left_flg) {
+ selb_mode = _bits_vct_get_left_index(selb_mode);
+ pr_debug("BHT MSG:shift left index\n");
+ }
+ }
+ selb_mode = TRUNING_RING_IDX(selb_mode);
+ }
+ if (pmax_pass_win)
+ *pmax_pass_win = tuning_pass_num_max;
+
+ return selb_mode;
+}
+
+
+int get_best_window_phase(u32 vct, int *pmax_pass_win)
+{
+ return _get_best_window_phase(vct, pmax_pass_win, 0);
+}
+
+static int _ggc_get_suitable_selb_for_next_tuning(struct sdhci_host *host)
+{
+ int selb = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 inj_tx_selb = BIT_PASS_MASK;
+
+ if (selx_failure_point_exist(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) {
+ selb = vendor_host->ggc.ggc_sw_selb_tuning_first_selb;
+ } else {
+ pr_debug("BHT MSG:manual inject for all pass case\n");
+ if (is_bus_mode_sdr104(host))
+ inj_tx_selb &= SDR104_MANUAL_INJECT;
+ else
+ inj_tx_selb &= SDR50_MANUAL_INJECT;
+
+ pr_debug("BHT MSG:manual inject for all pass case, inj_tx_selb=0x%x\n",
+ inj_tx_selb);
+ selb = get_best_window_phase(inj_tx_selb, NULL);
+ pr_debug("BHT MSG:select selb %d for all pass case\n", selb);
+ }
+ return selb;
+}
+
+static int ggc_get_tuning_cnt_from_buffer(struct sdhci_host *host)
+{
+ int cnt = 0;
+ u8 data[512];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ cnt = (int)cfg_read_bits_ofs_mask(data, &vendor_host->ggc.cmd19_cnt_cfg);
+
+ pr_debug("BHT MSG:tuning cnt=%d\n", cnt);
+ return cnt;
+}
+
+bool ggc_hw_inject_ext(struct sdhci_host *host, bool *card_status,
+ u32 sel200, u32 sel100, bool writetobh201)
+{
+ bool ret = TRUE;
+ u8 data[512];
+ struct t_gg_reg_strt gg_reg_arr[10];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 i = 0;
+ u32 reg;
+
+ pr_debug("BHT MSG:%s sel200:%xh,sel100:%xh\n", __func__, sel200, sel100);
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.inject_failure_for_tuning_enable_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.inject_failure_for_200m_tuning_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.inject_failure_for_100m_tuning_cfg,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = 1;
+ gg_reg_arr[1].value = sel200;
+ gg_reg_arr[2].value = sel100;
+
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 3, TRUE);
+ if (writetobh201)
+ ret = gg_emulator_write_ext(host, card_status, data, 512);
+ else {
+ pr_debug("BHT MSG:%s: dump config data instead write to bh201\n", __func__);
+ for (i = 0; i < 128; i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("BHT MSG: ggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+ }
+ return ret;
+}
+
+bool _ggc_hw_inject_may_recursive(struct sdhci_host *host, u32 sel200,
+ u32 sel100, int max_recur, bool writetobh201)
+{
+ bool ret = TRUE, card_status = TRUE;
+ int selb = BIT_PASS_MASK;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ ret = ggc_hw_inject_ext(host, &card_status, vendor_host->ggc.ggc_cmd_tx_selb_failed_range,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, writetobh201);
+ pr_debug("BHT MSG:ret:%x\n", ret);
+ if ((ret == FALSE) && (card_status == FALSE)) {
+ pr_debug("BHT MSG:inject again when hw inject\n");
+ selb &= ~GENERATE_IDX_VALUE(vendor_host->ggc.ggc_sw_selb_tuning_first_selb);
+ tx_selb_inject_policy(host, selb);
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+
+ if (((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) >= 5)) {
+ pr_err("BHT ERR:pass windows too small,reinit recursive\n");
+ return FALSE;
+ }
+
+ if (max_recur--)
+ return _ggc_hw_inject_may_recursive(host,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, max_recur, writetobh201);
+ else
+ return FALSE;
+ } else
+ return TRUE;
+}
+
+bool ggc_hw_inject_may_recursive(struct sdhci_host *host, u32 sel200,
+ u32 sel100, bool writetobh201)
+{
+ return _ggc_hw_inject_may_recursive(host, sel200, sel100, 4, writetobh201);
+}
+
+bool get_next_dll_voltage(int cur, int *next, u32 *dll_voltage_unlock_cnt,
+ int *dll_voltage_scan_map)
+{
+ int min_idx = 0, cur_cnt = 0, next_cnt = 0;
+ int cur_flg = 0;
+ int i = 0;
+ u8 ret = 0;
+
+ pr_warn("BHT WARN:dll_voltage_unlock_cnt:%x %x %x %x\n",
+ dll_voltage_unlock_cnt[0], dll_voltage_unlock_cnt[1],
+ dll_voltage_unlock_cnt[2], dll_voltage_unlock_cnt[3]);
+ pr_warn("BHT WARN:dll_voltage_scan_map:%x %x %x %x\n",
+ dll_voltage_scan_map[0], dll_voltage_scan_map[1],
+ dll_voltage_scan_map[2], dll_voltage_scan_map[3]);
+ for (i = 1; i < 4; i++) {
+ if (cur_flg == 0) {
+ if (dll_voltage_scan_map[(cur + i) % 4] != 0)
+ continue;
+ cur_cnt = dll_voltage_unlock_cnt[(cur + i) % 4];
+ cur_flg = 1;
+ min_idx = (cur + i) % 4;
+ continue;
+ } else {
+ if (dll_voltage_scan_map[(cur + i) % 4] != 0)
+ continue;
+ next_cnt = dll_voltage_unlock_cnt[(cur + i) % 4];
+ if (cur_cnt > next_cnt) {
+ cur_cnt = next_cnt;
+ min_idx = (cur + i) % 4;
+ }
+ }
+ }
+ if (cur_flg == 0) {
+ pr_err("BHT ERR:no find available voltage\n");
+ ret = FALSE;
+ } else {
+ *next = min_idx;
+ pr_err("BHT ERR:next available voltage %d\n", min_idx);
+ ret = TRUE;
+ }
+ return ret;
+}
+
+bool ggc_sw_calc_tuning_result(struct sdhci_host *host, bool *card_status,
+ bool *read_status, u32 *tx_selb, u32 *all_selb, u64 *raw_tx_selb)
+{
+ bool ret = FALSE;
+ bool card_ret = FALSE;
+ bool read_ret = FALSE;
+ u32 selb_status_tx_low32 = 0, selb_status_tx_high32 = 0;
+ u32 selb_status_ggc_low32 = 0, selb_status_ggc_high32 = 0;
+ struct t_gg_reg_strt gg_reg_arr[8] = {{0}};
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.pha_stas_tx_low32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.pha_stas_tx_high32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.pha_stas_rx_low32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.pha_stas_rx_high32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_sela_after_mask,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_after_mask,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.dll_delay_100m_backup,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.dll_delay_200m_backup,
+ sizeof(struct t_gg_reg_strt));
+
+ ret = ggc_read_registers_ext(host, &card_ret, &read_ret, gg_reg_arr, 8);
+ if (read_ret == TRUE) {
+ selb_status_tx_low32 = gg_reg_arr[0].value;
+ pr_debug("BHT MSG:[205-236]:\n");
+ log_bin(selb_status_tx_low32);
+ selb_status_tx_high32 = gg_reg_arr[1].value;
+ pr_debug("BHT MSG:[237-268]:\n");
+ log_bin(selb_status_tx_high32);
+ selb_status_ggc_low32 = gg_reg_arr[2].value;
+ pr_debug("BHT MSG:[14-45]:\n");
+ log_bin(selb_status_ggc_low32);
+ selb_status_ggc_high32 = gg_reg_arr[3].value;
+ pr_debug("BHT MSG:[46-77]:\n");
+ log_bin(selb_status_ggc_high32);
+ pr_debug("BHT MSG:dll sela after mask=%xh", gg_reg_arr[4].value);
+ pr_debug("BHT MSG:dll selb after mask=%xh", gg_reg_arr[5].value);
+
+ if (raw_tx_selb) {
+ *raw_tx_selb = gg_reg_arr[1].value;
+ (*raw_tx_selb) <<= 32;
+ *raw_tx_selb += gg_reg_arr[0].value;
+ pr_debug("BHT MSG:raw_tx_selb:%llxh\n", *raw_tx_selb);
+ }
+
+ if (tx_selb) {
+ gen_array_data(gg_reg_arr[0].value, gg_reg_arr[1].value,
+ tx_selb);
+ pr_debug("BHT MSG:tx_selb:%xh\n", *tx_selb);
+ }
+ if (all_selb) {
+ gen_array_data(gg_reg_arr[2].value, gg_reg_arr[3].value,
+ all_selb);
+ pr_debug("BHT MSG:all_selb:%xh\n", *all_selb);
+ }
+ }
+
+ if (read_status)
+ (*read_status) = read_ret;
+ if (card_status)
+ (*card_status) = card_ret;
+
+ if (card_status && read_status)
+ pr_debug("BHT MSG:card_status,read_status:%x %x\n", *card_status, *read_status);
+ return ret;
+}
+
+bool _ggc_calc_cur_sela_tuning_result(struct sdhci_host *host, int cur_sela, int start_selb)
+{
+ bool read_status = FALSE;
+ bool card_status = FALSE;
+ bool ret = TRUE;
+ u32 tx_selb, all_selb;
+ u64 raw_tx_selb = 0;
+ bool retuning_flg = FALSE;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int selb;
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+ enum tuning_stat_et *psela_tuning_result = ggc->ggc_sela_tuning_result;
+
+ ret = ggc_sw_calc_tuning_result(host, &card_status,
+ &read_status, &tx_selb, &all_selb, &raw_tx_selb);
+
+ if (card_status == FALSE) {
+ if (read_status == TRUE) {
+ selb = get_selb_failure_point(start_selb, raw_tx_selb,
+ ggc_get_tuning_cnt_from_buffer(host));
+ pr_debug("BHT MSG:inject selb %03x for CMD7 read timeout\n", selb);
+ tx_selb_inject_policy(host, selb);
+ } else {
+ pr_debug("BHT MSG:%s dll:%xh read status failed\n",
+ __func__, cur_sela);
+ }
+ ret = FALSE;
+ goto exit;
+ } else {
+ if (read_status == TRUE) {
+ if (selx_failure_point_exist(tx_selb)) {
+ if ((11-get_bit_number(tx_selb)) <= 3) {
+ tx_selb_inject_policy(host, tx_selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ } else if (get_bit_number(tx_selb) == 0) {
+ selb = get_selb_failure_point(start_selb, raw_tx_selb,
+ ggc_get_tuning_cnt_from_buffer(host));
+ tx_selb_inject_policy(host, selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, selb);
+ tx_selb_failed_history_update(host, selb);
+ retuning_flg = TRUE;
+ } else {
+ tx_selb_inject_policy(host, tx_selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ retuning_flg = TRUE;
+ }
+
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host, ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, TRUE);
+ } else {
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ }
+
+ if (retuning_flg == TRUE) {
+ pr_debug("BHT MSG: %s dll:%xh need retuning\n",
+ __func__, cur_sela);
+ psela_tuning_result[cur_sela] = RETUNING_CASE;
+ } else {
+ pr_debug("BHT MSG: %s dll:%xh pass\n",
+ __func__, cur_sela);
+ psela_tuning_result[cur_sela] = OUTPUT_PASS_TYPE;
+ }
+ } else {
+ psela_tuning_result[cur_sela] = READ_STATUS_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ pr_debug("BHT MSG:== %s dll:%xh read status failed ==\n",
+ __func__, cur_sela);
+ }
+ }
+exit:
+ return ret;
+}
+static int sdhci_bht_sdr104_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+ struct mmc_host *mmc = host->mmc;
+
+ return sdhci_msm_bayhub_execute_tuning(mmc, opcode);
+}
+
+static int sd_tuning_sw(struct sdhci_host *host)
+{
+ int ret = 0;
+
+ if (is_bus_mode_sdr104(host))
+ ret = sdhci_bht_sdr104_execute_tuning(host, 0x13);
+ else
+ ret = sdhci_bht_sdr50_execute_tuning(host, 0x13);
+
+ return ret;
+}
+
+static bool sd_gg_tuning_status(struct sdhci_host *host,
+ u32 *tx_selb, u32 *all_selb, u64 *raw_tx_selb,
+ bool *status_ret, bool *first_cmd19_status)
+{
+ bool ret = TRUE;
+ int err = sd_tuning_sw(host);
+
+ ret = err == 0 ? TRUE : FALSE;
+ if (err == -ETIMEDOUT) {
+ ret = FALSE;
+ if (first_cmd19_status)
+ *first_cmd19_status = false;
+ goto exit;
+ }
+
+ if (status_ret) {
+ *status_ret =
+ gg_tuning_result(host, tx_selb, all_selb,
+ raw_tx_selb);
+ } else {
+ gg_tuning_result(host, 0, 0, 0);
+ }
+
+exit:
+ return ret;
+}
+
+static bool ggc_sd_tuning(struct sdhci_host *host,
+ bool *first_cmd19_status)
+{
+ bool ret = TRUE;
+ int err = sd_tuning_sw(host);
+
+ ret = err == 0 ? TRUE : FALSE;
+ if (err == -ETIMEDOUT) {
+ ret = FALSE;
+ if (first_cmd19_status)
+ *first_cmd19_status = false;
+ goto exit;
+ }
+
+exit:
+ return ret;
+}
+
+static bool _ggc_output_tuning(struct sdhci_host *host, u8 *selb_pass_win)
+{
+ int cur_sela = 0, dll_sela_cnt = 0;
+ int dll_sela_basis = 0;
+ bool ret = FALSE;
+ u8 win_tb[12] = { 0 };
+ u8 win_mid = 0;
+ u8 win_max = 0;
+ u32 tx_tmp = 0;
+ int target_sela = 0;
+ int target_selb = 0;
+ u32 all_sela, tx_selb, all_selb;
+ u64 raw_tx_selb;
+ bool status_ret = FALSE;
+ int cur_selb = 0;
+ int tuning_error_type[16] = { 0 };
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+ enum tuning_stat_et *psela_tuning_result = ggc->ggc_sela_tuning_result;
+ int i = 0;
+ u32 idx_r, idx_c;
+ u32 min_pos = 0;
+ u32 all_selb_ar[TUNING_PHASE_SIZE] = { 0 };
+ u32 pass_cnt[TUNING_PHASE_SIZE] = { 0 };
+ u32 cfg = 0;
+ int rescan_selb_cnt = 0;
+ int returning_selb_cnt = 0;
+ bool first_cmd19_sta = TRUE;
+ int next = 0;
+ bool card_status = TRUE;
+ int selb = BIT_PASS_MASK;
+ u8 all_str[TUNING_PHASE_SIZE + 1], tx_str[TUNING_PHASE_SIZE + 1];
+
+ ggc->driver_strength_reinit_flg = 0;
+ vendor_host->ggc.dll_unlock_reinit_flg = 0;
+ dll_sela_basis = get_config_sela_setting(host);
+ cur_selb = get_config_selb_setting(host);
+
+ if (ggc->tuning_cmd7_timeout_reinit_flg) {
+ ggc->tuning_cmd7_timeout_reinit_flg = 0;
+ dll_sela_basis = vendor_host->ggc.ggc_cur_sela;
+ cur_selb = vendor_host->ggc.ggc_sw_selb_tuning_first_selb;
+ pr_debug
+ ("BHT MSG:Tuning start sela: 0x%x, selb: 0x%x where CMD7 timeout\n",
+ dll_sela_basis, cur_selb);
+ }
+
+ for (dll_sela_cnt = 0; dll_sela_cnt < TUNING_PHASE_SIZE; dll_sela_cnt++) {
+ cur_sela =
+ (dll_sela_cnt + dll_sela_basis) % TUNING_PHASE_SIZE;
+ ggc->ggc_cur_sela = cur_sela;
+ pr_debug("BHT MSG: %s select sela dll: %x, selb dll: %x\n",
+ __func__, cur_sela, cur_selb);
+ if (psela_tuning_result[cur_sela] != NO_TUNING) {
+ pr_debug("BHT MSG:sela tuning=%d already tuning,so skip it\n", cur_sela);
+ continue;
+ }
+rescan_selb:
+ host_cmddat_line_reset(host);
+
+ if (dll_sela_cnt == 0) {
+ if (!selx_failure_point_exist
+ (vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) {
+ rescan_selb_cnt = 3;
+ pr_debug("BHT MSG:no need rescan case\n");
+ }
+ status_ret = FALSE;
+ ret = ggc_sd_tuning(host, &first_cmd19_sta);
+
+ if (first_cmd19_sta == FALSE) {
+ _check_bus_mode(host);
+ ggc->cur_bus_mode->dll_voltage_unlock_cnt
+ [ggc->cur_dll_voltage_idx]++;
+ ggc->dll_voltage_scan_map[ggc->cur_dll_voltage_idx] = 1;
+ if (get_next_dll_voltage(ggc->cur_dll_voltage_idx, &next,
+ ggc->cur_bus_mode->dll_voltage_unlock_cnt,
+ ggc->dll_voltage_scan_map) == TRUE)
+ ggc->cur_dll_voltage_idx = next;
+ else
+ ggc->cur_dll_voltage_idx =
+ (ggc->cur_dll_voltage_idx + 1) % 4;
+
+ pr_err("BHT ERR:first cmd19 timeout\n");
+ vendor_host->ggc.dll_unlock_reinit_flg = 1;
+ _ggc_reset_tuning_result_for_dll(host);
+ ret = FALSE;
+ goto exit;
+ }
+ } else if ((is_bus_mode_sdr104(host) == FALSE)
+ && vendor_host->ggc.sdr50_notuning_sela_inject_flag == 1
+ && !GET_IDX_VALUE(vendor_host->ggc.sdr50_notuning_sela_rx_inject,
+ cur_sela)) {
+ pr_debug("BHT MSG:skip %d\n", cur_sela);
+ tuning_error_type[cur_sela] = READ_STATUS_FAIL_TYPE;
+ goto cur_sela_failed;
+ } else {
+ ret = ggc_set_output_tuning_phase_ext(host, &card_status,
+ cur_sela, update_selb(host, cur_selb));
+ if (ret == FALSE || card_status == FALSE) {
+ pr_err
+ ("BHT ERR: output_tuning fail at phase %d,ret=%d,card_status=%d\n",
+ cur_sela, ret, card_status);
+ if (card_status == FALSE) {
+ selb &= ~GENERATE_IDX_VALUE(cur_selb);
+ pr_err("BHT ERR:inject selb %d for update sela/selb fail\n",
+ selb);
+ tx_selb_inject_policy(host, selb);
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host,
+ ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, TRUE);
+
+ if (((11 - get_bit_number(
+ ggc->ggc_cmd_tx_selb_failed_range)) >= 5)) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small\n");
+
+ ggc->driver_strength_reinit_flg =
+ current_ds < 7 ? current_ds + 1 : 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+
+ goto exit;
+ }
+ cur_selb = _ggc_get_suitable_selb_for_next_tuning(host);
+ }
+ psela_tuning_result[cur_sela] = RETUNING_CASE;
+ goto retuning_case;
+ }
+ ret = ggc_sd_tuning(host, NULL);
+ }
+
+ if (ret == FALSE) {
+ pr_err("BHT ERR:Error when output_tuning, fail at phase %d\n",
+ cur_sela);
+ psela_tuning_result[cur_sela] = TUNING_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ continue;
+ }
+
+ ret = _ggc_calc_cur_sela_tuning_result(host, cur_sela, cur_selb);
+
+ if ((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) >= 5) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small after result calculate, reinit\n");
+ if (current_ds < 7)
+ ggc->driver_strength_reinit_flg = current_ds + 1;
+ else
+ ggc->driver_strength_reinit_flg = 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+ pr_err("BHT ERR:will change driver strength from %d to %d\n",
+ current_ds,
+ ggc->driver_strength_reinit_flg);
+ goto exit;
+ }
+
+ if (ret == FALSE) {
+ pr_err("BHT ERR:cmd7 timeout fail,reinit\n");
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 1;
+
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host, ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, FALSE);
+ if ((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range))
+ >= 5) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small, driver strength reinit\n");
+
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 0;
+
+ ggc->driver_strength_reinit_flg =
+ current_ds < 7 ? current_ds + 1 : 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+ pr_err("BHT ERR:will change driver strength from %d to %d\n",
+ current_ds,
+ ggc->driver_strength_reinit_flg);
+ goto exit;
+ }
+ goto exit;
+ }
+
+ cur_selb = _ggc_get_suitable_selb_for_next_tuning(host);
+
+ pr_debug("BHT MSG: output sela:%xh pass\n", cur_sela);
+ rescan_selb_cnt++;
+ if ((rescan_selb_cnt < 3) &&
+ (selx_failure_point_exist(vendor_host->ggc.ggc_cmd_tx_selb_failed_range))) {
+ pr_debug("BHT MSG:rescan cnt %d, ggc_cmd_tx_selb_failed_range=0x%x\n",
+ rescan_selb_cnt,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ goto rescan_selb;
+ }
+
+retuning_case:
+ if (psela_tuning_result[cur_sela] == RETUNING_CASE) {
+ returning_selb_cnt++;
+ if (returning_selb_cnt < 3) {
+ rescan_selb_cnt = 0;
+ pr_debug("BHT MSG:retuning %d\n", rescan_selb_cnt);
+ goto rescan_selb;
+ } else {
+ psela_tuning_result[cur_sela] = SET_PHASE_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ continue;
+ }
+ }
+
+ goto next_dll_sela;
+
+cur_sela_failed:
+ pr_debug("BHT MSG:read status failedB\n");
+ all_selb = 0;
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ pr_debug("BHT MSG: output sela:%xh failed ===\n", cur_sela);
+next_dll_sela:
+ if ((is_bus_mode_sdr104(host) == FALSE)
+ && vendor_host->ggc.sdr50_notuning_crc_error_flag) {
+ u32 fp = 0;
+
+ fp = GENERATE_IDX_VALUE(cur_sela);
+ fp |= GENERATE_IDX_VALUE((cur_sela + 1) % TUNING_PHASE_SIZE);
+ fp |= GENERATE_IDX_VALUE((cur_sela + 10) % TUNING_PHASE_SIZE);
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject &= ~fp;
+ vendor_host->ggc.sdr50_notuning_sela_inject_flag = 1;
+ pr_debug("BHT MSG:sdr50_notuning_sela_rx_inject:%x\n",
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject);
+ ret = FALSE;
+ goto exit;
+ };
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ phase_str(all_str, all_selb_failed_tb_get(host, i));
+ phase_str(tx_str, tx_selb_failed_tb_get(host, i));
+ pr_debug
+ ("BHT MSG:DLL sela[%x] all selb: %s tx selb: %s [%xh,%xh] %s\n",
+ i, all_str, tx_str,
+ all_selb_failed_tb_get(host, i),
+ tx_selb_failed_tb_get(host, i),
+ op_dbg_str[tuning_error_type[i]]);
+
+ }
+
+ /* remove margin passed all selb phase */
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ all_selb_ar[i] = all_selb_failed_tb_get(host, i);
+
+ /* calculate cumulation of diagonal bits */
+ for (idx_c = 0; idx_c < TUNING_PHASE_SIZE; idx_c++) {
+ for (idx_r = 0; idx_r < TUNING_PHASE_SIZE;
+ idx_r++) {
+ pass_cnt[idx_c] += ((all_selb_ar[idx_r] >>
+ ((idx_r + idx_c) % TUNING_PHASE_SIZE)) & 0x01);
+ }
+ if (idx_c == 0)
+ min_pos = 0;
+ else if (pass_cnt[idx_c] < pass_cnt[min_pos])
+ min_pos = idx_c;
+ }
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ all_selb_ar[i] &= ~(1 << (min_pos + i) % TUNING_PHASE_SIZE);
+ all_selb_failed_tb_update(host, i, all_selb_ar[i]);
+ }
+
+ tx_selb = tx_selb_failed_history_get(host);
+
+ pr_debug("inject sw selb & merge tx_selb failed point to all_selb\n");
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ all_selb_failed_tb_update(host, i, tx_selb);
+
+ pr_debug("BHT MSG:inject sw sela failed point to all_selb\n");
+ if (is_bus_mode_sdr104(host))
+ cfg = 0x7ff;
+ else
+ cfg = 0x7ff;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(cfg, i) == 0)
+ all_selb_failed_tb_update(host, i, 0);
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ phase_str(all_str, all_selb_failed_tb_get(host, i));
+ phase_str(tx_str, tx_selb_failed_tb_get(host, i));
+ pr_debug("BHT MSG:DLL sela[%x] all selb: %s tx selb: %s [%xh,%xh] %s\n",
+ i, all_str, tx_str,
+ all_selb_failed_tb_get(host, i),
+ tx_selb_failed_tb_get(host, i),
+ op_dbg_str[tuning_error_type[i]]);
+ }
+
+ tx_selb = tx_selb_failed_history_get(host);
+ tx_selb &= 0x7ff;
+ tx_tmp = tx_selb;
+
+ pr_debug("BHT MSG:---selb merge---\n");
+ if ((tx_selb&0x7ff) == 0x7ff) {
+ if (is_bus_mode_sdr104(host)) {
+ u32 cfg = SDR104_MANUAL_INJECT;
+
+ tx_selb &= cfg;
+ pr_debug("tx selb:%xh SDR104 inject:%xh merge tx_selb:%xh\n",
+ tx_tmp, cfg, tx_selb);
+ } else {
+ u32 cfg = SDR50_MANUAL_INJECT;
+
+ tx_selb &= cfg;
+ pr_debug("tx selb:%xh SDR50 inject:%xh merge tx_selb:%xh\n",
+ tx_tmp, cfg, tx_selb);
+ }
+ }
+
+ if (tx_selb == 0) {
+ pr_err("all failed, force fixed phase sela selb to default\n");
+ target_selb =
+ get_config_selb_setting(host);
+ target_sela =
+ get_config_sela_setting(host);
+ goto final;
+ }
+ phase_str(win_tb, tx_selb);
+ pr_debug("BHT MSG: tx selb[%xh] 11 bit: %s\n",
+ tx_selb, win_tb);
+ bits_generate_array(win_tb, tx_selb);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ target_selb = win_mid;
+
+ all_sela = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ u32 all_selb = all_selb_failed_tb_get(host, i);
+
+ phase_str(win_tb, all_selb);
+ pr_debug("BHT MSG: all_selb[%xh] 11 bit: %s\n",
+ all_selb, win_tb);
+ bits_generate_array(win_tb, all_selb);
+ chk_phase_window(win_tb, &win_mid,
+ &win_max);
+ *selb_pass_win = win_max;
+ if (all_selb & (1 << target_selb))
+ all_sela |= 1 << i;
+ }
+
+ phase_str(win_tb, all_sela);
+ pr_debug("BHT MSG: all_sela[%xh] 11 bit: %s\n",
+ all_sela, win_tb);
+ bits_generate_array(win_tb, all_sela);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ target_sela = win_mid;
+
+final:
+
+ gg_fix_output_tuning_phase(host, target_sela,
+ target_selb);
+
+ ret = sd_gg_tuning_status(host, &tx_selb,
+ &all_selb, &raw_tx_selb, &status_ret, NULL);
+ if (ret == FALSE) {
+ pr_err("Error when output_tuning, sd_tuning fail\n");
+ ret = FALSE;
+ goto exit;
+ }
+
+ /* use final pass windows */
+ phase_str(win_tb, all_selb);
+ pr_debug("BHT MSG: all_selb[%xh] 11 bit: %s\n",
+ all_selb, win_tb);
+ bits_generate_array(win_tb, all_selb);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ *selb_pass_win = win_max;
+
+ vendor_host->ggc.selx_tuning_done_flag = 1;
+
+exit:
+ pr_debug("BHT MSG:exit:%s %d\n", __func__, ret);
+ return ret;
+}
+
+static int sdhci_bht_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u8 tw = 0;
+ int ret = 0;
+
+ if (vendor_host->ggc.bh201_used) {
+ pr_debug("BHT MSG:enter bht tuning\n");
+ if (host->clock < CORE_FREQ_100MHZ) {
+ pr_debug("BHT MSG:%d less 100Mhz,no tuning\n", host->clock);
+ return 0;
+ }
+
+ if (vendor_host->ggc.tuning_in_progress) {
+ pr_debug("BHT MSG:tuning_in_progress\n");
+ return 0;
+ }
+ vendor_host->ggc.tuning_in_progress = true;
+
+ if (vendor_host->ggc.selx_tuning_done_flag) {
+ pr_debug("BHT MSG:GGC tuning is done, just do vendor host tuning");
+ if (is_bus_mode_sdr104(host))
+ ret = sdhci_bht_sdr104_execute_tuning(host, 0x13);
+ else
+ ret = sdhci_bht_sdr50_execute_tuning(host, 0x13);
+ } else {
+ ret = !_ggc_output_tuning(host, &tw);
+ }
+ vendor_host->ggc.tuning_in_progress = false;
+ return ret;
+ } else
+ return sdhci_msm_bayhub_execute_tuning(vendor_host->mmc, opcode);
+}
+
+/*
+ * sdhci_msm_bayhub_hs400 - Calibrate the DLL for HS400 bus speed mode operation.
+ * This needs to be done for both tuning and enhanced_strobe mode.
+ * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz
+ * fixed feedback clock is used.
+ */
+static void sdhci_msm_bayhub_hs400(struct sdhci_host *host, struct mmc_ios *ios)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ if (host->clock > CORE_FREQ_100MHZ &&
+ (msm_bayhub_host->tuning_done || ios->enhanced_strobe) &&
+ !msm_bayhub_host->calibration_done) {
+ ret = sdhci_msm_bayhub_hs400_dll_calibration(host);
+ if (!ret)
+ msm_bayhub_host->calibration_done = true;
+ else
+ pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n",
+ mmc_hostname(host->mmc), ret);
+ }
+}
+
+static void sdhci_msm_bayhub_set_uhs_signaling(struct sdhci_host *host,
+ unsigned int uhs)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u16 ctrl_2;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ /* Select Bus Speed Mode for host */
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ switch (uhs) {
+ case MMC_TIMING_UHS_SDR12:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
+ break;
+ case MMC_TIMING_UHS_SDR25:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
+ break;
+ case MMC_TIMING_MMC_HS400:
+ case MMC_TIMING_MMC_HS200:
+ case MMC_TIMING_UHS_SDR104:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
+ break;
+ case MMC_TIMING_UHS_DDR50:
+ case MMC_TIMING_MMC_DDR52:
+ ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
+ break;
+ }
+
+ /*
+ * When clock frequency is less than 100MHz, the feedback clock must be
+ * provided and DLL must not be used so that tuning can be skipped. To
+ * provide feedback clock, the mode selection can be any value less
+ * than 3'b011 in bits [2:0] of HOST CONTROL2 register.
+ */
+ if (host->clock <= CORE_FREQ_100MHZ) {
+ if (uhs == MMC_TIMING_MMC_HS400 ||
+ uhs == MMC_TIMING_MMC_HS200 ||
+ uhs == MMC_TIMING_UHS_SDR104)
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ /*
+ * DLL is not required for clock <= 100MHz
+ * Thus, make sure DLL it is disabled when not required
+ */
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ /*
+ * The DLL needs to be restored and CDCLP533 recalibrated
+ * when the clock frequency is set back to 400MHz.
+ */
+ msm_bayhub_host->calibration_done = false;
+ }
+
+ dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
+ mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+ if (mmc->ios.timing == MMC_TIMING_MMC_HS400)
+ sdhci_msm_bayhub_hs400(host, &mmc->ios);
+}
+
+static int sdhci_msm_bayhub_set_pincfg(struct sdhci_msm_bayhub_host *msm_bayhub_host, bool level)
+{
+ struct platform_device *pdev = msm_bayhub_host->pdev;
+ int ret;
+
+ if (level)
+ ret = pinctrl_pm_select_default_state(&pdev->dev);
+ else
+ ret = pinctrl_pm_select_sleep_state(&pdev->dev);
+
+ return ret;
+}
+
+static int sdhci_msm_bayhub_set_vmmc(struct mmc_host *mmc)
+{
+ if (IS_ERR(mmc->supply.vmmc))
+ return 0;
+
+ return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
+}
+
+static int msm_bayhub_toggle_vqmmc(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool level)
+{
+ int ret;
+ struct mmc_ios ios;
+
+ if (msm_bayhub_host->vqmmc_enabled == level)
+ return 0;
+
+ if (level) {
+ /* Set the IO voltage regulator to default voltage level */
+ if (msm_bayhub_host->caps_0 & CORE_3_0V_SUPPORT)
+ ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330;
+ else if (msm_bayhub_host->caps_0 & CORE_1_8V_SUPPORT)
+ ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180;
+
+ if (msm_bayhub_host->caps_0 & CORE_VOLT_SUPPORT) {
+ ret = mmc_regulator_set_vqmmc(mmc, &ios);
+ if (ret < 0) {
+ dev_err(mmc_dev(mmc), "%s: vqmmc set volgate failed: %d\n",
+ mmc_hostname(mmc), ret);
+ goto out;
+ }
+ }
+ ret = regulator_enable(mmc->supply.vqmmc);
+ } else {
+ ret = regulator_disable(mmc->supply.vqmmc);
+ }
+
+ if (ret)
+ dev_err(mmc_dev(mmc), "%s: vqmm %sable failed: %d\n",
+ mmc_hostname(mmc), level ? "en":"dis", ret);
+ else
+ msm_bayhub_host->vqmmc_enabled = level;
+out:
+ return ret;
+}
+
+static int msm_bayhub_config_vqmmc_mode(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool hpm)
+{
+ int load, ret;
+
+ load = hpm ? MMC_VQMMC_MAX_LOAD_UA : 0;
+ ret = regulator_set_load(mmc->supply.vqmmc, load);
+ if (ret)
+ dev_err(mmc_dev(mmc), "%s: vqmmc set load failed: %d\n",
+ mmc_hostname(mmc), ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_set_vqmmc(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool level)
+{
+ int ret;
+ bool always_on;
+
+ if (IS_ERR(mmc->supply.vqmmc) ||
+ (mmc->ios.power_mode == MMC_POWER_UNDEFINED))
+ return 0;
+ /*
+ * For eMMC don't turn off Vqmmc, Instead just configure it in LPM
+ * and HPM modes by setting the corresponding load.
+ *
+ * Till eMMC is initialized (i.e. always_on == 0), just turn on/off
+ * Vqmmc. Vqmmc gets turned off only if init fails and mmc_power_off
+ * gets invoked. Once eMMC is initialized (i.e. always_on == 1),
+ * Vqmmc should remain ON, So just set the load instead of turning it
+ * off/on.
+ */
+ always_on = !mmc_card_is_removable(mmc) &&
+ mmc->card && mmc_card_mmc(mmc->card);
+
+ if (always_on)
+ ret = msm_bayhub_config_vqmmc_mode(msm_bayhub_host, mmc, level);
+ else
+ ret = msm_bayhub_toggle_vqmmc(msm_bayhub_host, mmc, level);
+
+ return ret;
+}
+
+static inline void sdhci_msm_bayhub_init_pwr_irq_wait(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ init_waitqueue_head(&msm_bayhub_host->pwr_irq_wait);
+}
+
+static inline void sdhci_msm_bayhub_complete_pwr_irq_wait(
+ struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ wake_up(&msm_bayhub_host->pwr_irq_wait);
+}
+
+/*
+ * sdhci_msm_bayhub_check_power_status API should be called when registers writes
+ * which can toggle sdhci IO bus ON/OFF or change IO lines HIGH/LOW happens.
+ * To what state the register writes will change the IO lines should be passed
+ * as the argument req_type. This API will check whether the IO line's state
+ * is already the expected state and will wait for power irq only if
+ * power irq is expected to be triggered based on the current IO line state
+ * and expected IO line state.
+ */
+static void sdhci_msm_bayhub_check_power_status(struct sdhci_host *host, u32 req_type)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ bool done = false;
+ u32 val = SWITCHABLE_SIGNALING_VOLTAGE;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n",
+ mmc_hostname(host->mmc), __func__, req_type,
+ msm_bayhub_host->curr_pwr_state, msm_bayhub_host->curr_io_level);
+
+ /*
+ * The power interrupt will not be generated for signal voltage
+ * switches if SWITCHABLE_SIGNALING_VOLTAGE in MCI_GENERICS is not set.
+ * Since sdhci-msm_bayhub-v5, this bit has been removed and SW must consider
+ * it as always set.
+ */
+ if (!msm_bayhub_host->mci_removed)
+ val = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_generics);
+ if ((req_type & REQ_IO_HIGH || req_type & REQ_IO_LOW) &&
+ !(val & SWITCHABLE_SIGNALING_VOLTAGE)) {
+ return;
+ }
+
+ /*
+ * The IRQ for request type IO High/LOW will be generated when -
+ * there is a state change in 1.8V enable bit (bit 3) of
+ * SDHCI_HOST_CONTROL2 register. The reset state of that bit is 0
+ * which indicates 3.3V IO voltage. So, when MMC core layer tries
+ * to set it to 3.3V before card detection happens, the
+ * IRQ doesn't get triggered as there is no state change in this bit.
+ * The driver already handles this case by changing the IO voltage
+ * level to high as part of controller power up sequence. Hence, check
+ * for host->pwr to handle a case where IO voltage high request is
+ * issued even before controller power up.
+ */
+ if ((req_type & REQ_IO_HIGH) && !host->pwr) {
+ pr_debug("%s: do not wait for power IRQ that never comes, req_type: %d\n",
+ mmc_hostname(host->mmc), req_type);
+ return;
+ }
+ if ((req_type & msm_bayhub_host->curr_pwr_state) ||
+ (req_type & msm_bayhub_host->curr_io_level))
+ done = true;
+ /*
+ * This is needed here to handle cases where register writes will
+ * not change the current bus state or io level of the controller.
+ * In this case, no power irq will be triggerred and we should
+ * not wait.
+ */
+ if (!done) {
+ if (!wait_event_timeout(msm_bayhub_host->pwr_irq_wait,
+ msm_bayhub_host->pwr_irq_flag,
+ msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS)))
+ dev_warn(&msm_bayhub_host->pdev->dev,
+ "%s: pwr_irq for req: (%d) timed out\n",
+ mmc_hostname(host->mmc), req_type);
+ }
+ pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc),
+ __func__, req_type);
+}
+
+static void sdhci_msm_bayhub_dump_pwr_ctrl_regs(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x\n",
+ mmc_hostname(host->mmc),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_status),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_mask),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_ctl));
+}
+
+static void sdhci_msm_bayhub_handle_pwr_irq(struct sdhci_host *host, int irq)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_host *mmc = host->mmc;
+ u32 irq_status, irq_ack = 0;
+ int retry = 10, ret;
+ u32 pwr_state = 0, io_level = 0;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ irq_status = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_pwrctl_status);
+ irq_status &= INT_MASK;
+
+ msm_bayhub_host_writel(msm_bayhub_host, irq_status, host,
+ msm_bayhub_offset->core_pwrctl_clear);
+
+ /*
+ * There is a rare HW scenario where the first clear pulse could be
+ * lost when actual reset and clear/read of status register is
+ * happening at a time. Hence, retry for at least 10 times to make
+ * sure status register is cleared. Otherwise, this will result in
+ * a spurious power IRQ resulting in system instability.
+ */
+ while (irq_status & msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_pwrctl_status)) {
+ if (retry == 0) {
+ pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n",
+ mmc_hostname(host->mmc), irq_status);
+ sdhci_msm_bayhub_dump_pwr_ctrl_regs(host);
+ WARN_ON(1);
+ break;
+ }
+ msm_bayhub_host_writel(msm_bayhub_host, irq_status, host,
+ msm_bayhub_offset->core_pwrctl_clear);
+ retry--;
+ udelay(10);
+ }
+
+ /* Handle BUS ON/OFF*/
+ if (irq_status & CORE_PWRCTL_BUS_ON) {
+ if (msm_bayhub_host->ggc.bh201_used)
+ bh201_signal_voltage_on_off(host, 1);
+ pwr_state = REQ_BUS_ON;
+ io_level = REQ_IO_HIGH;
+ }
+ if (irq_status & CORE_PWRCTL_BUS_OFF) {
+ if (msm_bayhub_host->ggc.bh201_used)
+ bh201_signal_voltage_on_off(host, 0);
+ pwr_state = REQ_BUS_OFF;
+ io_level = REQ_IO_LOW;
+ }
+
+ if (pwr_state) {
+ ret = sdhci_msm_bayhub_set_vmmc(mmc);
+ if (!ret)
+ ret = sdhci_msm_bayhub_set_vqmmc(msm_bayhub_host, mmc,
+ pwr_state & REQ_BUS_ON);
+ if (!ret)
+ ret = sdhci_msm_bayhub_set_pincfg(msm_bayhub_host,
+ pwr_state & REQ_BUS_ON);
+ if (!ret)
+ irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+ else
+ irq_ack |= CORE_PWRCTL_BUS_FAIL;
+ }
+
+ /* Handle IO LOW/HIGH */
+ if (irq_status & CORE_PWRCTL_IO_LOW)
+ io_level = REQ_IO_LOW;
+
+ if (irq_status & CORE_PWRCTL_IO_HIGH)
+ io_level = REQ_IO_HIGH;
+
+ if (io_level)
+ irq_ack |= CORE_PWRCTL_IO_SUCCESS;
+
+ if (io_level && !IS_ERR(mmc->supply.vqmmc) && !pwr_state) {
+ ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios);
+ if (ret < 0) {
+ dev_err(mmc_dev(mmc), "%s: IO_level setting failed(%d). signal_voltage: %d, vdd: %d irq_status: 0x%08x\n",
+ mmc_hostname(mmc), ret,
+ mmc->ios.signal_voltage, mmc->ios.vdd,
+ irq_status);
+ irq_ack |= CORE_PWRCTL_IO_FAIL;
+ }
+ }
+
+ /*
+ * The driver has to acknowledge the interrupt, switch voltages and
+ * report back if it succeeded or not to this register. The voltage
+ * switches are handled by the sdhci core, so just report success.
+ */
+ msm_bayhub_host_writel(msm_bayhub_host, irq_ack, host,
+ msm_bayhub_offset->core_pwrctl_ctl);
+
+ /*
+ * If we don't have info regarding the voltage levels supported by
+ * regulators, don't change the IO PAD PWR SWITCH.
+ */
+ if (msm_bayhub_host->caps_0 & CORE_VOLT_SUPPORT) {
+ u32 new_config;
+ /*
+ * We should unset IO PAD PWR switch only if the register write
+ * can set IO lines high and the regulator also switches to 3 V.
+ * Else, we should keep the IO PAD PWR switch set.
+ * This is applicable to certain targets where eMMC vccq supply
+ * is only 1.8V. In such targets, even during REQ_IO_HIGH, the
+ * IO PAD PWR switch must be kept set to reflect actual
+ * regulator voltage. This way, during initialization of
+ * controllers with only 1.8V, we will set the IO PAD bit
+ * without waiting for a REQ_IO_LOW.
+ */
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ new_config = config;
+
+ if ((io_level & REQ_IO_HIGH) &&
+ (msm_bayhub_host->caps_0 & CORE_3_0V_SUPPORT))
+ new_config &= ~CORE_IO_PAD_PWR_SWITCH;
+ else if ((io_level & REQ_IO_LOW) ||
+ (msm_bayhub_host->caps_0 & CORE_1_8V_SUPPORT))
+ new_config |= CORE_IO_PAD_PWR_SWITCH;
+
+ if (config ^ new_config)
+ writel_relaxed(new_config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ }
+
+ if (pwr_state)
+ msm_bayhub_host->curr_pwr_state = pwr_state;
+ if (io_level)
+ msm_bayhub_host->curr_io_level = io_level;
+
+ dev_dbg(mmc_dev(mmc), "%s: %s: Handled IRQ(%d), irq_status=0x%x, ack=0x%x\n",
+ mmc_hostname(msm_bayhub_host->mmc), __func__, irq, irq_status,
+ irq_ack);
+}
+
+static irqreturn_t sdhci_msm_bayhub_pwr_irq(int irq, void *data)
+{
+ struct sdhci_host *host = (struct sdhci_host *)data;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ sdhci_msm_bayhub_handle_pwr_irq(host, irq);
+ msm_bayhub_host->pwr_irq_flag = 1;
+ sdhci_msm_bayhub_complete_pwr_irq_wait(msm_bayhub_host);
+
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int sdhci_msm_bayhub_get_max_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct clk *core_clk = msm_bayhub_host->bulk_clks[0].clk;
+
+ return clk_round_rate(core_clk, ULONG_MAX);
+}
+
+static unsigned int sdhci_msm_bayhub_get_min_clock(struct sdhci_host *host)
+{
+ return SDHCI_MSM_MIN_CLOCK;
+}
+
+/**
+ * __sdhci_msm_bayhub_set_clock - sdhci_msm_bayhub clock control.
+ *
+ * Description:
+ * MSM controller does not use internal divider and
+ * instead directly control the GCC clock as per
+ * HW recommendation.
+ **/
+static void __sdhci_msm_bayhub_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ u16 clk;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ /*
+ * MSM controller do not use clock divider.
+ * Thus read SDHCI_CLOCK_CONTROL and only enable
+ * clock with no divider value programmed.
+ */
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ sdhci_enable_clk(host, clk);
+}
+
+/* sdhci_msm_bayhub_set_clock - Called with (host->lock) spinlock held. */
+static void sdhci_msm_bayhub_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!clock) {
+ host->mmc->actual_clock = msm_bayhub_host->clk_rate = 0;
+ goto out;
+ }
+
+ sdhci_msm_bayhub_hc_select_mode(host);
+
+ msm_bayhub_set_clock_rate_for_bus_mode(host, clock);
+out:
+ __sdhci_msm_bayhub_set_clock(host, clock);
+}
+
+/*****************************************************************************\
+ * *
+ * MSM Command Queue Engine (CQE) *
+ * *
+\*****************************************************************************/
+
+static u32 sdhci_msm_bayhub_cqe_irq(struct sdhci_host *host, u32 intmask)
+{
+ int cmd_error = 0;
+ int data_error = 0;
+
+ if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
+ return intmask;
+
+ cqhci_irq(host->mmc, intmask, cmd_error, data_error);
+ return 0;
+}
+
+static void sdhci_msm_bayhub_cqe_disable(struct mmc_host *mmc, bool recovery)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+ u32 ctrl;
+
+ /*
+ * When CQE is halted, the legacy SDHCI path operates only
+ * on 16-byte descriptors in 64bit mode.
+ */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ host->desc_sz = 16;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ /*
+ * During CQE command transfers, command complete bit gets latched.
+ * So s/w should clear command complete interrupt status when CQE is
+ * either halted or disabled. Otherwise unexpected SDCHI legacy
+ * interrupt gets triggered when CQE is halted/disabled.
+ */
+ ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
+ ctrl |= SDHCI_INT_RESPONSE;
+ sdhci_writel(host, ctrl, SDHCI_INT_ENABLE);
+ sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ sdhci_cqe_disable(mmc, recovery);
+}
+
+static const struct cqhci_host_ops sdhci_msm_bayhub_cqhci_ops = {
+ .enable = sdhci_cqe_enable,
+ .disable = sdhci_msm_bayhub_cqe_disable,
+};
+
+static int sdhci_msm_bayhub_cqe_add_host(struct sdhci_host *host,
+ struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct cqhci_host *cq_host;
+ bool dma64;
+ u32 cqcfg;
+ int ret;
+
+ /*
+ * When CQE is halted, SDHC operates only on 16byte ADMA descriptors.
+ * So ensure ADMA table is allocated for 16byte descriptors.
+ */
+ if (host->caps & SDHCI_CAN_64BIT)
+ host->alloc_desc_sz = 16;
+
+ ret = sdhci_setup_host(host);
+ if (ret)
+ return ret;
+
+ cq_host = cqhci_pltfm_init(pdev);
+ if (IS_ERR(cq_host)) {
+ ret = PTR_ERR(cq_host);
+ dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
+ goto cleanup;
+ }
+
+ msm_bayhub_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
+ cq_host->ops = &sdhci_msm_bayhub_cqhci_ops;
+
+ dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
+
+ ret = cqhci_init(cq_host, host->mmc, dma64);
+ if (ret) {
+ dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
+ mmc_hostname(host->mmc), ret);
+ goto cleanup;
+ }
+
+ /* Disable cqe reset due to cqe enable signal */
+ cqcfg = cqhci_readl(cq_host, CQHCI_VENDOR_CFG1);
+ cqcfg |= CQHCI_VENDOR_DIS_RST_ON_CQ_EN;
+ cqhci_writel(cq_host, cqcfg, CQHCI_VENDOR_CFG1);
+
+ /*
+ * SDHC expects 12byte ADMA descriptors till CQE is enabled.
+ * So limit desc_sz to 12 so that the data commands that are sent
+ * during card initialization (before CQE gets enabled) would
+ * get executed without any issues.
+ */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ host->desc_sz = 12;
+
+ ret = __sdhci_add_host(host);
+ if (ret)
+ goto cleanup;
+
+ dev_info(&pdev->dev, "%s: CQE init: success\n",
+ mmc_hostname(host->mmc));
+ return ret;
+
+cleanup:
+ sdhci_cleanup_host(host);
+ return ret;
+}
+
+/*
+ * Platform specific register write functions. This is so that, if any
+ * register write needs to be followed up by platform specific actions,
+ * they can be added here. These functions can go to sleep when writes
+ * to certain registers are done.
+ * These functions are relying on sdhci_set_ios not using spinlock.
+ */
+static int __sdhci_msm_bayhub_check_write(struct sdhci_host *host, u16 val, int reg)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 req_type = 0;
+
+ switch (reg) {
+ case SDHCI_HOST_CONTROL2:
+ req_type = (val & SDHCI_CTRL_VDD_180) ? REQ_IO_LOW :
+ REQ_IO_HIGH;
+ break;
+ case SDHCI_SOFTWARE_RESET:
+ if (host->pwr && (val & SDHCI_RESET_ALL))
+ req_type = REQ_BUS_OFF;
+ break;
+ case SDHCI_POWER_CONTROL:
+ req_type = !val ? REQ_BUS_OFF : REQ_BUS_ON;
+ break;
+ case SDHCI_TRANSFER_MODE:
+ msm_bayhub_host->transfer_mode = val;
+ break;
+ case SDHCI_COMMAND:
+ if (!msm_bayhub_host->use_cdr)
+ break;
+ if ((msm_bayhub_host->transfer_mode & SDHCI_TRNS_READ) &&
+ SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK_HS200 &&
+ SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK)
+ sdhci_msm_bayhub_set_cdr(host, true);
+ else
+ sdhci_msm_bayhub_set_cdr(host, false);
+ break;
+ }
+
+ if (req_type) {
+ msm_bayhub_host->pwr_irq_flag = 0;
+ /*
+ * Since this register write may trigger a power irq, ensure
+ * all previous register writes are complete by this point.
+ */
+ mb();
+ }
+ return req_type;
+}
+
+/* This function may sleep*/
+static void sdhci_msm_bayhub_writew(struct sdhci_host *host, u16 val, int reg)
+{
+ u32 req_type = 0;
+
+ req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
+ writew_relaxed(val, host->ioaddr + reg);
+
+ if (req_type)
+ sdhci_msm_bayhub_check_power_status(host, req_type);
+}
+
+/* This function may sleep*/
+static void sdhci_msm_bayhub_writeb(struct sdhci_host *host, u8 val, int reg)
+{
+ u32 req_type = 0;
+
+ req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
+
+ writeb_relaxed(val, host->ioaddr + reg);
+
+ if (req_type)
+ sdhci_msm_bayhub_check_power_status(host, req_type);
+}
+
+static void sdhci_msm_bayhub_set_regulator_caps(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ struct mmc_host *mmc = msm_bayhub_host->mmc;
+ struct regulator *supply = mmc->supply.vqmmc;
+ u32 caps = 0, config;
+ struct sdhci_host *host = mmc_priv(mmc);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ if (regulator_is_supported_voltage(supply, 1700000, 1950000))
+ caps |= CORE_1_8V_SUPPORT;
+ if (regulator_is_supported_voltage(supply, 2700000, 3600000))
+ caps |= CORE_3_0V_SUPPORT;
+
+ if (!caps)
+ pr_warn("%s: 1.8/3V not supported for vqmmc\n",
+ mmc_hostname(mmc));
+ }
+
+ if (caps) {
+ /*
+ * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH
+ * bit can be used as required later on.
+ */
+ u32 io_level = msm_bayhub_host->curr_io_level;
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ config |= CORE_IO_PAD_PWR_SWITCH_EN;
+
+ if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT))
+ config &= ~CORE_IO_PAD_PWR_SWITCH;
+ else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT))
+ config |= CORE_IO_PAD_PWR_SWITCH;
+
+ writel_relaxed(config,
+ host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ }
+ msm_bayhub_host->caps_0 |= caps;
+ pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
+}
+
+static void sdhci_msm_bayhub_reset(struct sdhci_host *host, u8 mask)
+{
+ if ((host->mmc->caps2 & MMC_CAP2_CQE) && (mask & SDHCI_RESET_ALL))
+ cqhci_deactivate(host->mmc);
+ sdhci_reset(host, mask);
+}
+
+static int sdhci_msm_bayhub_register_vreg(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ int ret;
+
+ ret = mmc_regulator_get_supply(msm_bayhub_host->mmc);
+ if (ret)
+ return ret;
+
+ sdhci_msm_bayhub_set_regulator_caps(msm_bayhub_host);
+
+ return 0;
+}
+
+static int sdhci_msm_bayhub_start_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ u16 ctrl, status;
+
+ /*
+ * Signal Voltage Switching is only applicable for Host Controllers
+ * v3.00 and above.
+ */
+ if (host->version < SDHCI_SPEC_300)
+ return 0;
+
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ switch (ios->signal_voltage) {
+ case MMC_SIGNAL_VOLTAGE_330:
+ if (!(host->flags & SDHCI_SIGNALING_330))
+ return -EINVAL;
+
+ /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+ ctrl &= ~SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_SIGNAL_VOLTAGE_180:
+ if (!(host->flags & SDHCI_SIGNALING_180))
+ return -EINVAL;
+
+ /* Enable 1.8V Signal Enable in the Host Control2 register */
+ ctrl |= SDHCI_CTRL_VDD_180;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
+
+ /* regulator output should be stable within 5 ms */
+ status = ctrl & SDHCI_CTRL_VDD_180;
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if ((ctrl & SDHCI_CTRL_VDD_180) == status)
+ return 0;
+
+ dev_warn(mmc_dev(mmc), "%s: Regulator output did not became stable\n",
+ mmc_hostname(mmc));
+
+ return -EAGAIN;
+}
+
+#define DRIVER_NAME "sdhci_msm_bayhub"
+#define SDHCI_MSM_DUMP(f, x...) \
+ pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
+
+static void sdhci_msm_bayhub_dump_vendor_regs(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ SDHCI_MSM_DUMP("----------- VENDOR REGISTER DUMP -----------\n");
+
+ SDHCI_MSM_DUMP(
+ "DLL sts: 0x%08x | DLL cfg: 0x%08x | DLL cfg2: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_status),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_2));
+ SDHCI_MSM_DUMP(
+ "DLL cfg3: 0x%08x | DLL usr ctl: 0x%08x | DDR cfg: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_3),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_usr_ctl),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_config));
+ SDHCI_MSM_DUMP(
+ "Vndr func: 0x%08x | Vndr func2 : 0x%08x Vndr func3: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec),
+ readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec_func2),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec3));
+}
+
+static const struct sdhci_msm_bayhub_variant_ops mci_var_ops = {
+ .msm_bayhub_readl_relaxed = sdhci_msm_bayhub_mci_variant_readl_relaxed,
+ .msm_bayhub_writel_relaxed = sdhci_msm_bayhub_mci_variant_writel_relaxed,
+};
+
+static const struct sdhci_msm_bayhub_variant_ops v5_var_ops = {
+ .msm_bayhub_readl_relaxed = sdhci_msm_bayhub_v5_variant_readl_relaxed,
+ .msm_bayhub_writel_relaxed = sdhci_msm_bayhub_v5_variant_writel_relaxed,
+};
+
+static const struct sdhci_msm_bayhub_variant_info sdhci_msm_bayhub_v5_var = {
+ .mci_removed = true,
+ .var_ops = &v5_var_ops,
+ .offset = &sdhci_msm_bayhub_v5_offset,
+};
+
+static const struct sdhci_msm_bayhub_variant_info sdm845_sdhci_var = {
+ .mci_removed = true,
+ .restore_dll_config = true,
+ .var_ops = &v5_var_ops,
+ .offset = &sdhci_msm_bayhub_v5_offset,
+};
+
+static const struct of_device_id sdhci_msm_bayhub_dt_match[] = {
+ {.compatible = "qcom,sdhci-msm-bayhub-v5", .data = &sdhci_msm_bayhub_v5_var},
+ {.compatible = "qcom,sdm845-bayhub-sdhci", .data = &sdm845_sdhci_var},
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, sdhci_msm_bayhub_dt_match);
+
+static const struct sdhci_ops sdhci_msm_bayhub_ops = {
+ .reset = sdhci_msm_bayhub_reset,
+ .set_clock = sdhci_msm_bayhub_set_clock,
+ .get_min_clock = sdhci_msm_bayhub_get_min_clock,
+ .get_max_clock = sdhci_msm_bayhub_get_max_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .set_uhs_signaling = sdhci_msm_bayhub_set_uhs_signaling,
+ .write_w = sdhci_msm_bayhub_writew,
+ .write_b = sdhci_msm_bayhub_writeb,
+ .irq = sdhci_msm_bayhub_cqe_irq,
+ .dump_vendor_regs = sdhci_msm_bayhub_dump_vendor_regs,
+ .set_power = sdhci_set_power_noreg,
+};
+
+static const struct sdhci_pltfm_data sdhci_msm_bayhub_pdata = {
+ .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+ SDHCI_QUIRK_SINGLE_POWER_WRITE |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,
+
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
+ .ops = &sdhci_msm_bayhub_ops,
+};
+
+static inline void sdhci_msm_bayhub_get_of_property(struct platform_device *pdev,
+ struct sdhci_host *host)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (of_property_read_u32(node, "qcom,ddr-config",
+ &msm_bayhub_host->ddr_config))
+ msm_bayhub_host->ddr_config = DDR_CONFIG_POR_VAL;
+
+ of_property_read_u32(node, "qcom,dll-config", &msm_bayhub_host->dll_config);
+}
+
+static int sdhci_msm_bayhub_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_msm_bayhub_host *msm_bayhub_host;
+ struct resource *core_memres;
+ struct clk *clk;
+ int ret;
+ u16 host_version, core_minor;
+ u32 core_version, config;
+ u8 core_major;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset;
+ const struct sdhci_msm_bayhub_variant_info *var_info;
+ struct device_node *node = pdev->dev.of_node;
+
+ host = sdhci_pltfm_init(pdev, &sdhci_msm_bayhub_pdata, sizeof(*msm_bayhub_host));
+ if (IS_ERR(host))
+ return PTR_ERR(host);
+
+ host->sdma_boundary = 0;
+ pltfm_host = sdhci_priv(host);
+ msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ msm_bayhub_host->mmc = host->mmc;
+ msm_bayhub_host->pdev = pdev;
+
+ ret = mmc_of_parse(host->mmc);
+ if (ret)
+ goto pltfm_free;
+
+ if (of_find_property(node, "use-bayhub-bh201", NULL)) {
+ sdhci_bh201_parse(msm_bayhub_host->mmc);
+ INIT_DELAYED_WORK(&host->mmc->detect, mmc_rescan_bayhub);
+ } else
+ msm_bayhub_host->ggc.bh201_used = 0;
+
+ /*
+ * Based on the compatible string, load the required msm_bayhub host info from
+ * the data associated with the version info.
+ */
+ var_info = of_device_get_match_data(&pdev->dev);
+
+ msm_bayhub_host->mci_removed = var_info->mci_removed;
+ msm_bayhub_host->restore_dll_config = var_info->restore_dll_config;
+ msm_bayhub_host->var_ops = var_info->var_ops;
+ msm_bayhub_host->offset = var_info->offset;
+ msm_bayhub_host->uses_tassadar_dll = var_info->uses_tassadar_dll;
+
+ msm_bayhub_offset = msm_bayhub_host->offset;
+
+ sdhci_get_of_property(pdev);
+ sdhci_msm_bayhub_get_of_property(pdev, host);
+
+ msm_bayhub_host->saved_tuning_phase = INVALID_TUNING_PHASE;
+
+ /* Setup SDCC bus voter clock. */
+ msm_bayhub_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
+ if (!IS_ERR(msm_bayhub_host->bus_clk)) {
+ /* Vote for max. clk rate for max. performance */
+ ret = clk_set_rate(msm_bayhub_host->bus_clk, INT_MAX);
+ if (ret)
+ goto pltfm_free;
+ ret = clk_prepare_enable(msm_bayhub_host->bus_clk);
+ if (ret)
+ goto pltfm_free;
+ }
+
+ /* Setup main peripheral bus clock */
+ clk = devm_clk_get(&pdev->dev, "iface");
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
+ dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret);
+ goto bus_clk_disable;
+ }
+ msm_bayhub_host->bulk_clks[1].clk = clk;
+
+ /* Setup SDC MMC clock */
+ clk = devm_clk_get(&pdev->dev, "core");
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
+ dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret);
+ goto bus_clk_disable;
+ }
+ msm_bayhub_host->bulk_clks[0].clk = clk;
+
+ /* Check for optional interconnect paths */
+ ret = dev_pm_opp_of_find_icc_paths(&pdev->dev, NULL);
+ if (ret)
+ goto bus_clk_disable;
+
+ msm_bayhub_host->opp_table = dev_pm_opp_set_clkname(&pdev->dev, "core");
+ if (IS_ERR(msm_bayhub_host->opp_table)) {
+ ret = PTR_ERR(msm_bayhub_host->opp_table);
+ goto bus_clk_disable;
+ }
+
+ /* OPP table is optional */
+ ret = dev_pm_opp_of_add_table(&pdev->dev);
+ if (!ret) {
+ msm_bayhub_host->has_opp_table = true;
+ } else if (ret != -ENODEV) {
+ dev_err(&pdev->dev, "Invalid OPP table in Device tree\n");
+ goto opp_cleanup;
+ }
+
+ /* Vote for maximum clock rate for maximum performance */
+ ret = dev_pm_opp_set_rate(&pdev->dev, INT_MAX);
+ if (ret)
+ dev_warn(&pdev->dev, "core clock boost failed\n");
+
+ clk = devm_clk_get(&pdev->dev, "cal");
+ if (IS_ERR(clk))
+ clk = NULL;
+ msm_bayhub_host->bulk_clks[2].clk = clk;
+
+ clk = devm_clk_get(&pdev->dev, "sleep");
+ if (IS_ERR(clk))
+ clk = NULL;
+ msm_bayhub_host->bulk_clks[3].clk = clk;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (ret)
+ goto opp_cleanup;
+
+ /*
+ * xo clock is needed for FLL feature of cm_dll.
+ * In case if xo clock is not mentioned in DT, warn and proceed.
+ */
+ msm_bayhub_host->xo_clk = devm_clk_get(&pdev->dev, "xo");
+ if (IS_ERR(msm_bayhub_host->xo_clk)) {
+ ret = PTR_ERR(msm_bayhub_host->xo_clk);
+ dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret);
+ }
+
+ if (!msm_bayhub_host->mci_removed) {
+ core_memres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ msm_bayhub_host->core_mem = devm_ioremap_resource(&pdev->dev,
+ core_memres);
+
+ if (IS_ERR(msm_bayhub_host->core_mem)) {
+ ret = PTR_ERR(msm_bayhub_host->core_mem);
+ goto clk_disable;
+ }
+ }
+
+ /* Reset the vendor spec register to power on reset state */
+ writel_relaxed(CORE_VENDOR_SPEC_POR_VAL,
+ host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ if (!msm_bayhub_host->mci_removed) {
+ /* Set HC_MODE_EN bit in HC_MODE register */
+ msm_bayhub_host_writel(msm_bayhub_host, HC_MODE_EN, host,
+ msm_bayhub_offset->core_hc_mode);
+ config = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_hc_mode);
+ config |= FF_CLK_SW_RST_DIS;
+ msm_bayhub_host_writel(msm_bayhub_host, config, host,
+ msm_bayhub_offset->core_hc_mode);
+ }
+
+ host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
+ dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
+ host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
+ SDHCI_VENDOR_VER_SHIFT));
+
+ core_version = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_mci_version);
+ core_major = (core_version & CORE_VERSION_MAJOR_MASK) >>
+ CORE_VERSION_MAJOR_SHIFT;
+ core_minor = core_version & CORE_VERSION_MINOR_MASK;
+ dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
+ core_version, core_major, core_minor);
+
+ if (core_major == 1 && core_minor >= 0x42)
+ msm_bayhub_host->use_14lpp_dll_reset = true;
+
+ /*
+ * SDCC 5 controller with major version 1, minor version 0x34 and later
+ * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL.
+ */
+ if (core_major == 1 && core_minor < 0x34)
+ msm_bayhub_host->use_cdclp533 = true;
+
+ /*
+ * Support for some capabilities is not advertised by newer
+ * controller versions and must be explicitly enabled.
+ */
+ if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
+ config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
+ config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec_capabilities0);
+ }
+
+ if (core_major == 1 && core_minor >= 0x49)
+ msm_bayhub_host->updated_ddr_cfg = true;
+
+ ret = sdhci_msm_bayhub_register_vreg(msm_bayhub_host);
+ if (ret)
+ goto clk_disable;
+
+ /*
+ * Power on reset state may trigger power irq if previous status of
+ * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq
+ * interrupt in GIC, any pending power irq interrupt should be
+ * acknowledged. Otherwise power irq interrupt handler would be
+ * fired prematurely.
+ */
+ sdhci_msm_bayhub_handle_pwr_irq(host, 0);
+
+ /*
+ * Ensure that above writes are propogated before interrupt enablement
+ * in GIC.
+ */
+ mb();
+
+ /* Setup IRQ for handling power/voltage tasks with PMIC */
+ msm_bayhub_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
+ if (msm_bayhub_host->pwr_irq < 0) {
+ ret = msm_bayhub_host->pwr_irq;
+ goto clk_disable;
+ }
+
+ sdhci_msm_bayhub_init_pwr_irq_wait(msm_bayhub_host);
+ /* Enable pwr irq interrupts */
+ msm_bayhub_host_writel(msm_bayhub_host, INT_MASK, host,
+ msm_bayhub_offset->core_pwrctl_mask);
+
+ ret = devm_request_threaded_irq(&pdev->dev, msm_bayhub_host->pwr_irq, NULL,
+ sdhci_msm_bayhub_pwr_irq, IRQF_ONESHOT,
+ dev_name(&pdev->dev), host);
+ if (ret) {
+ dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret);
+ goto clk_disable;
+ }
+
+ msm_bayhub_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_NEED_RSP_BUSY;
+
+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev,
+ MSM_MMC_AUTOSUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(&pdev->dev);
+
+ host->mmc_host_ops.start_signal_voltage_switch =
+ sdhci_msm_bayhub_start_signal_voltage_switch;
+ if (msm_bayhub_host->ggc.bh201_used)
+ host->mmc_host_ops.execute_tuning = sdhci_bht_execute_tuning;
+ else
+ host->mmc_host_ops.execute_tuning = sdhci_msm_bayhub_execute_tuning;
+
+ if (of_property_read_bool(node, "supports-cqe"))
+ ret = sdhci_msm_bayhub_cqe_add_host(host, pdev);
+ else
+ ret = sdhci_add_host(host);
+ if (ret)
+ goto pm_runtime_disable;
+
+ pm_runtime_mark_last_busy(&pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
+ return 0;
+
+pm_runtime_disable:
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+clk_disable:
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+opp_cleanup:
+ if (msm_bayhub_host->has_opp_table)
+ dev_pm_opp_of_remove_table(&pdev->dev);
+ dev_pm_opp_put_clkname(msm_bayhub_host->opp_table);
+bus_clk_disable:
+ if (!IS_ERR(msm_bayhub_host->bus_clk))
+ clk_disable_unprepare(msm_bayhub_host->bus_clk);
+pltfm_free:
+ if (msm_bayhub_host->ggc.bh201_used) {
+ if (gpio_is_valid(msm_bayhub_host->ggc.det_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.det_gpio);
+ if (gpio_is_valid(msm_bayhub_host->ggc.pwr_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.pwr_gpio);
+ }
+
+ sdhci_pltfm_free(pdev);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
+ 0xffffffff);
+
+ sdhci_remove_host(host, dead);
+ if (msm_bayhub_host->ggc.bh201_used) {
+ if (gpio_is_valid(msm_bayhub_host->ggc.det_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.det_gpio);
+ if (gpio_is_valid(msm_bayhub_host->ggc.pwr_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.pwr_gpio);
+ }
+ if (msm_bayhub_host->has_opp_table)
+ dev_pm_opp_of_remove_table(&pdev->dev);
+ dev_pm_opp_put_clkname(msm_bayhub_host->opp_table);
+ pm_runtime_get_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (!IS_ERR(msm_bayhub_host->bus_clk))
+ clk_disable_unprepare(msm_bayhub_host->bus_clk);
+ sdhci_pltfm_free(pdev);
+ return 0;
+}
+
+static __maybe_unused int sdhci_msm_bayhub_runtime_suspend(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ /* Drop the performance vote */
+ dev_pm_opp_set_rate(dev, 0);
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+
+ return 0;
+}
+
+static __maybe_unused int sdhci_msm_bayhub_runtime_resume(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (ret)
+ return ret;
+ /*
+ * Whenever core-clock is gated dynamically, it's needed to
+ * restore the SDR DLL settings when the clock is ungated.
+ */
+ if (msm_bayhub_host->restore_dll_config && msm_bayhub_host->clk_rate)
+ ret = sdhci_msm_bayhub_restore_sdr_dll_config(host);
+
+ dev_pm_opp_set_rate(dev, msm_bayhub_host->clk_rate);
+
+ return ret;
+}
+
+static const struct dev_pm_ops sdhci_msm_bayhub_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(sdhci_msm_bayhub_runtime_suspend,
+ sdhci_msm_bayhub_runtime_resume,
+ NULL)
+};
+
+static struct platform_driver sdhci_msm_bayhub_driver = {
+ .probe = sdhci_msm_bayhub_probe,
+ .remove = sdhci_msm_bayhub_remove,
+ .driver = {
+ .name = "sdhci_msm_bayhub",
+ .of_match_table = sdhci_msm_bayhub_dt_match,
+ .pm = &sdhci_msm_bayhub_pm_ops,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+};
+
+module_platform_driver(sdhci_msm_bayhub_driver);
+
+MODULE_DESCRIPTION("Qualcomm-bayhub Secure Digital Host Controller Interface driver");
+MODULE_LICENSE("GPL v2");
--
2.25.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
2021-07-28 17:43 [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue chevron
@ 2021-08-20 18:20 ` Bjorn Andersson
2021-08-30 12:14 ` 回复: " Chevron Li (WH)
0 siblings, 1 reply; 5+ messages in thread
From: Bjorn Andersson @ 2021-08-20 18:20 UTC (permalink / raw)
To: chevron
Cc: agross, linux-arm-msm, linux-kernel, shaper.liu, xiaoguang.yu,
shirley.her
On Wed 28 Jul 10:43 PDT 2021, chevron wrote:
> Improve the signal integrity for long SD bus trace by using 845+BH201 SD host redriver chip
>
This is a large patch with a very short commit message, which likely is
the reason why you've not gotten any reviews.
What is this hardware? The commit message gives me a feeling that the
BH201 is an external redriver that has been paired with the SDM845
sometimes?
Please describe properly how the hardware setup looks like.
I did skim through the patch trying to figure out what you're doing and
gave you some feedback below, but this is far from a complete review.
And many of the things I point out repeats throughout the patch.
I think the first step is to figure out what this is and if your design
is the right one...
> Signed-off-by: chevron.li <chevron.li@bayhubtech.com>
Is your name really chevron.li? Perhaps Chevron Li?
> ---
> change in V1:
I'm not able to find v0, can you point me to it, because I would like to
understand why these changes was made:
> 1. copy Qualcomm driver base from sdhci-msm.c to sdhci-bayhub.c
Why do we need to duplicate all this code.
> 2. implement the BH201 chip initialization function at sdhci-bayhub.c
Submitting this as a large "copy sdhci-msm and implement BH201" makes it
impossible to figure out what the BH201 specific pieces (that needs the
review) are.
> 3. implement the BH201 chip power control function at sdhci-bayhub.c
> 4. implement the BH201 chip tuning function at sdhci-bayhub.c
> 5. re-implement mmc_rescan to match BH201 mode switch flow at sdhci-bayhub.c
If this is an external redriver, can this be paired with any other SDHCI
controller?
> ---
> ---
[..]
> diff --git a/drivers/mmc/host/sdhci-bayhub.c b/drivers/mmc/host/sdhci-bayhub.c
> new file mode 100644
> index 000000000000..75029470bd22
> --- /dev/null
> +++ b/drivers/mmc/host/sdhci-bayhub.c
> @@ -0,0 +1,6563 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Bayhub Technologies, Inc. BH201 SDHCI bridge IC for
> + * VENDOR SDHCI platform driver source file
> + *
> + * Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
The SPDX header covers this, so don't repeat the license text here.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/delay.h>
> +#include <linux/mmc/mmc.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/pm_opp.h>
> +#include <linux/slab.h>
> +#include <linux/iopoll.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/interconnect.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/mmc/host.h>
> +#include <linux/mmc/card.h>
> +#include <linux/mmc/sd.h>
> +#include <linux/io.h>
> +#include <linux/of_gpio.h>
> +
> +#include "sdhci-pltfm.h"
> +#include "cqhci.h"
> +#include "../core/core.h"
> +#include "../core/sd_ops.h"
> +#include "../core/sdio_ops.h"
> +#include "../core/mmc_ops.h"
> +#include "../core/sd.h"
> +#include "../core/bus.h"
> +#include "../core/host.h"
> +#include "../core/card.h"
> +#include "../core/pwrseq.h"
> +
> +#define TRUE 1
> +#define FALSE 0
Use "true" and "false"...
> +
> +#define SD_FNC_AM_SDR50 0x2
> +#define SD_FNC_AM_SDR104 0x3
> +#define BIT_PASS_MASK (0x7ff)
> +#define SDR104_MANUAL_INJECT 0x3ff
> +#define SDR50_MANUAL_INJECT 0x77f
> +
[..]
> +#define TUNING_PHASE_SIZE 11
> +#define GGC_CFG_DATA {0x07000000, 0x07364022, 0x01015412, 0x01062400,\
> + 0x10400076, 0x00025432, 0x01046076, 0x62011000,\
> + 0x30503106, 0x64141711, 0x10057513, 0x00336200,\
> + 0x00020006, 0x40000400, 0x12200310, 0x3A314177}
> +
> +struct ggc_bus_mode_cfg_t {
Does "_t" say this is a struct? No need for that as "struct ggc..."
already says "it's a struct".
> + u32 tx_selb_tb[TUNING_PHASE_SIZE];
> + u32 all_selb_tb[TUNING_PHASE_SIZE];
> + u32 tx_selb_failed_history;
> + int bus_mode;
> + int default_sela;
> + int default_selb;
> + u32 default_delaycode;
> + u32 dll_voltage_unlock_cnt[4];
> + u32 max_delaycode;
> + u32 min_delaycode;
> + u32 delaycode_narrowdown_index;
> + u32 fail_phase;
> +};
> +
> +enum tuning_stat_et {
Does "_et" make this an enum?
> + NO_TUNING = 0,
> + OUTPUT_PASS_TYPE = 1,
> + SET_PHASE_FAIL_TYPE = 2,
> + TUNING_FAIL_TYPE = 3,
> + READ_STATUS_FAIL_TYPE = 4,
> + TUNING_CMD7_TIMEOUT = 5,
> + RETUNING_CASE = 6,
> +};
> +
> +
> +struct t_gg_reg_strt {
What is a "t gg reg strt"?
> + u32 ofs;
> + u32 mask;
> + u32 value;
> +};
> +
> +struct rl_bit_lct {
> + u8 bits;
> + u8 rl_bits;
> +};
> +
> +struct chk_type_t {
This only time this is used, it's there to pass 3 bools into a function.
Just use function arguments.
> + u8 right_valid:1;
> + u8 first_valid:1;
> + u8 record_valid:1;
> + u8 reserved:5;
> +};
> +
> +static const char *const op_dbg_str[] = {
> + "no tuning",
> + "pass",
> + "set_phase_fail",
> + "tuning fail",
> + "read status fail",
> + "tuning CMD7 timeout",
> + "retuning case"
> +};
> +
> +struct ggc_platform_t {
What is this "ggc" and what "platform" does this represent?
> + struct ggc_bus_mode_cfg_t sdr50;
> + struct ggc_bus_mode_cfg_t sdr104;
> + struct ggc_bus_mode_cfg_t *cur_bus_mode;
> +
> + struct t_gg_reg_strt pha_stas_rx_low32;
> + struct t_gg_reg_strt pha_stas_rx_high32;
> + struct t_gg_reg_strt pha_stas_tx_low32;
> + struct t_gg_reg_strt pha_stas_tx_high32;
> + struct t_gg_reg_strt dll_sela_after_mask;
> + struct t_gg_reg_strt dll_selb_after_mask;
> +
> + struct t_gg_reg_strt dll_delay_100m_backup;
> + struct t_gg_reg_strt dll_delay_200m_backup;
> +
> + struct t_gg_reg_strt dll_sela_100m_cfg;
> + struct t_gg_reg_strt dll_sela_200m_cfg;
> + struct t_gg_reg_strt dll_selb_100m_cfg;
> + struct t_gg_reg_strt dll_selb_200m_cfg;
> + struct t_gg_reg_strt dll_selb_100m_cfg_en;
> + struct t_gg_reg_strt dll_selb_200m_cfg_en;
> + struct t_gg_reg_strt internl_tuning_en_100m;
> + struct t_gg_reg_strt internl_tuning_en_200m;
> + struct t_gg_reg_strt cmd19_cnt_cfg;
> +
> + struct t_gg_reg_strt inject_failure_for_tuning_enable_cfg;
> + struct t_gg_reg_strt inject_failure_for_200m_tuning_cfg;
> + struct t_gg_reg_strt inject_failure_for_100m_tuning_cfg;
> +
> + int def_sela_100m;
> + int def_sela_200m;
> + int def_selb_100m;
> + int def_selb_200m;
> +
> + u32 _gg_reg_cur[16];
> + u8 _cur_read_buf[512];
Why does these have a '_' prefix?
> +
> + bool dll_unlock_reinit_flg;
> + u8 driver_strength_reinit_flg;
> + bool tuning_cmd7_timeout_reinit_flg;
> + u32 tuning_cmd7_timeout_reinit_cnt;
> + u32 ggc_cur_sela;
> + bool selx_tuning_done_flag;
> + u32 ggc_cmd_tx_selb_failed_range;
> + int ggc_sw_selb_tuning_first_selb;
> + enum tuning_stat_et ggc_sela_tuning_result[11];
> + int dll_voltage_scan_map[4];
> + int cur_dll_voltage_idx;
> + int sdr50_notuning_sela_inject_flag;
> + int sdr50_notuning_crc_error_flag;
> + u32 sdr50_notuning_sela_rx_inject;
> + u32 bh201_sdr50_sela_sw_inject;
> + u32 bh201_sdr50_selb_hw_inject;
> + u32 bh201_sdr104_selb_hw_inject;
> + u32 bh201_drive_strength;
> + bool tuning_in_progress;
> + int bh201_used;
> + int pwr_gpio; /* External power enable pin for Redriver IC */
> + int det_gpio;
> +};
[..]
> +static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_v5_offset = {
> + .core_mci_data_cnt = 0x35c,
> + .core_mci_status = 0x324,
> + .core_mci_fifo_cnt = 0x308,
> + .core_mci_version = 0x318,
> + .core_generics = 0x320,
> + .core_testbus_config = 0x32c,
> + .core_testbus_sel2_bit = 3,
> + .core_testbus_ena = (1 << 31),
> + .core_testbus_sel2 = (1 << 3),
> + .core_pwrctl_status = 0x240,
> + .core_pwrctl_mask = 0x244,
> + .core_pwrctl_clear = 0x248,
> + .core_pwrctl_ctl = 0x24c,
> + .core_sdcc_debug_reg = 0x358,
> + .core_dll_config = 0x200,
> + .core_dll_status = 0x208,
> + .core_vendor_spec = 0x20c,
> + .core_vendor_spec_adma_err_addr0 = 0x214,
> + .core_vendor_spec_adma_err_addr1 = 0x218,
> + .core_vendor_spec_func2 = 0x210,
> + .core_vendor_spec_capabilities0 = 0x21c,
> + .core_ddr_200_cfg = 0x224,
> + .core_vendor_spec3 = 0x250,
> + .core_dll_config_2 = 0x254,
> + .core_dll_config_3 = 0x258,
> + .core_ddr_config = 0x25c,
> + .core_dll_usr_ctl = 0x388,
> +};
> +
> +static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_mci_offset = {
This is unused and as such you don't need the sdhci_msm_bayhub_offset
either.
> + .core_hc_mode = 0x78,
> + .core_mci_data_cnt = 0x30,
> + .core_mci_status = 0x34,
> + .core_mci_fifo_cnt = 0x44,
> + .core_mci_version = 0x050,
> + .core_generics = 0x70,
> + .core_testbus_config = 0x0cc,
> + .core_testbus_sel2_bit = 4,
> + .core_testbus_ena = (1 << 3),
> + .core_testbus_sel2 = (1 << 4),
> + .core_pwrctl_status = 0xdc,
> + .core_pwrctl_mask = 0xe0,
> + .core_pwrctl_clear = 0xe4,
> + .core_pwrctl_ctl = 0xe8,
> + .core_sdcc_debug_reg = 0x124,
> + .core_dll_config = 0x100,
> + .core_dll_status = 0x108,
> + .core_vendor_spec = 0x10c,
> + .core_vendor_spec_adma_err_addr0 = 0x114,
> + .core_vendor_spec_adma_err_addr1 = 0x118,
> + .core_vendor_spec_func2 = 0x110,
> + .core_vendor_spec_capabilities0 = 0x11c,
> + .core_ddr_200_cfg = 0x184,
> + .core_vendor_spec3 = 0x1b0,
> + .core_dll_config_2 = 0x1b4,
> + .core_ddr_config_old = 0x1b8,
> + .core_ddr_config = 0x1bc,
> +};
> +
[..]
> +static const unsigned int freqs[] = { 400000, 300000, 200000, 100000 };
> +
> +static void cfg_bit_2_bt(int max_bit, int tar, int *byt, int *bit)
> +{
> + struct rl_bit_lct cfg_bit_map[6] = {
> + {0, 6}, {1, 5}, {2, 4},
> + {3, 2}, {4, 1}, {5, 0},
> + };
So you have an array of tuples, where the first entry in the tuple is
the index in the array? And then you only use rl_bits anyways...
How about:
u8 bit_map[6] = { 6, 5, 4, 2, 1, 0 }
> +
> + *byt = (max_bit - tar) / 6;
> + *bit = cfg_bit_map[(max_bit - tar) % 6].rl_bits;
> +}
> +
> +static u32 cfg_read_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
> +{
> + u32 rv = 0;
> + u32 msk = bts->mask;
> + int byt = 0, bit = 0;
> + int i = 0;
> +
> + do {
> + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
So "bt" is short for "byte" and "bts" is "bytes"?
> + if (cfg[byt] & (1 << bit))
> + rv |= 1 << i;
> +
> + i++;
> + msk >>= 1;
> + if (msk == 0)
> + break;
There's no case where mask is 0 (and I don't see why it would be), so
while (msk) {
...;
msk >>= 1;
}
Seems cleaner
But all of this would benefit from better naming and probably some
comments describing the actual format/structure of these bits and bytes.
> + } while (1);
> + return rv;
> +}
> +
> +static void get_default_setting(struct sdhci_host *host, u8 *data)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
> +
> + vendor_host->ggc.def_sela_100m =
> + cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
> + vendor_host->ggc.def_sela_200m =
> + cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
> + vendor_host->ggc.def_selb_100m =
> + cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
> + vendor_host->ggc.def_selb_200m =
> + cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
> +}
> +
> +static void cfg_write_bits_ofs_mask(u8 *cfg,
> + struct t_gg_reg_strt *bts, u32 w_value)
> +{
> + u32 wv = w_value & bts->mask;
> + u32 msk = bts->mask;
> + int byt = 0, bit = 0;
> + int i = 0;
> +
> + do {
> + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
> + if (wv & 1)
> + cfg[byt] |= (u8) (1 << bit);
> + else
> + cfg[byt] &= (u8) (~(1 << bit));
> +
> + i++;
> + wv >>= 1;
> + msk >>= 1;
> + if (msk == 0)
> + break;
> + } while (1);
> +}
> +
> +static void ram_bit_2_bt(int tar, int *byt, int *bit)
So the "ram" variant is just a regular bitmap with 8 bits per byte?
include/linux/bitmap.h gives your an interface for dealing with those.
> +{
> + *byt = tar / 8;
> + *bit = tar % 8;
> +}
> +
> +static void set_gg_reg_cur_val(struct ggc_platform_t *ggc,
> + u8 *data, u8 len)
> +{
> + memcpy(&ggc->_gg_reg_cur[0], data, len);
> +}
> +
> +static void get_gg_reg_cur_val(struct ggc_platform_t *ggc,
> + u8 *data, u8 len)
> +{
> + memcpy(data, &ggc->_gg_reg_cur[0], len);
> +}
> +
> +static void get_gg_reg_def(struct sdhci_host *host, u8 *data)
> +{
> + u32 gg_sw_def[16] = GGC_CFG_DATA;
> +
> + memcpy(data, (u8 *)&(gg_sw_def[0]), sizeof(gg_sw_def));
(u8 *)&(gg_sw_def[0])... The address of the first element, type casted
to a (u8*), then passed to a void *?
Isn't that the same thing as just typing "gg_sw_def"?
But why is GGC_CFG_DATA a define and not just a static const u32 array,
in which case you can replace this function with just a simple memcpy in
ggc_chip_init().
> +}
> +
> +static u32 read_ram_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
> +{
> + u32 rv = 0;
> + u32 msk = bts->mask;
> + int byt = 0, bit = 0;
> + int i = 0;
> +
> + do {
> + ram_bit_2_bt(bts->ofs + i, &byt, &bit);
> + if (cfg[byt] & (1 << bit))
> + rv |= 1 << i;
> +
> + i++;
> + msk >>= 1;
> + if (msk == 0)
> + break;
> +
> + } while (1);
> + return rv;
> +}
> +
> +static void ggc_dll_voltage_init(struct sdhci_host *host)
> +{
> + int i = 0;
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct sdhci_msm_bayhub_host *vendor_host =
> + sdhci_pltfm_priv(pltfm_host);
> +
> + for (i = 0; i < 4; i++) {
> + vendor_host->ggc.dll_voltage_scan_map[i] = 0;
> + vendor_host->ggc.sdr50.dll_voltage_unlock_cnt[i] = 0;
> + vendor_host->ggc.sdr104.dll_voltage_unlock_cnt[i] = 0;
> + }
> +}
> +
> +static void ggc_chip_init(struct sdhci_host *host)
> +{
> + u8 data[512] = { 0 };
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct sdhci_msm_bayhub_host *vendor_host =
> + sdhci_pltfm_priv(pltfm_host);
> +
> + get_gg_reg_def(host, data);
> + get_default_setting(host, data);
> + set_gg_reg_cur_val(&vendor_host->ggc, data, 64);
> +}
> +
> +static int driver_send_command7(struct sdhci_host *host)
> +{
> + int ret = 0;
> + int err;
> + struct mmc_host *mmc = host->mmc;
> + struct mmc_command cmd = {0};
> +
> + cmd.opcode = MMC_SELECT_CARD;
> + cmd.arg = 0;
> + cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
> + err = mmc_wait_for_cmd(mmc, &cmd, 3);
> + if (err)
> + ret = 0;
> + else
> + ret = 1;
> +
> + return ret;
return mmc_wait_for_cmd() seems more reasonable, but you don't check the
return value in any off the call sites...
> +}
> +
> +static void driver_send_command24(struct sdhci_host *host,
> + u32 *cfg_data, int data_len)
> +{
> + struct mmc_host *mmc = host->mmc;
> + struct mmc_request mrq = {0};
> + struct mmc_command cmd = { 0 };
> + struct mmc_data data = { 0 };
> + struct scatterlist sg;
> + u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
This allocation needs a NULL check.
> +
> + memcpy(data1, (u8 *)&(cfg_data[0]), data_len);
> + sg_init_one(&sg, data1, 512);
> +
> + cmd.opcode = MMC_WRITE_BLOCK;
> + cmd.arg = 0;
> + cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
> + data.blksz = 512;
> + data.blocks = 1;
> + data.flags = MMC_DATA_WRITE;
> + data.timeout_ns = 1000 * 1000 * 1000;
> + data.sg = &sg;
> + data.sg_len = 1;
> + mrq.cmd = &cmd;
> + mrq.data = &data;
> + mrq.stop = NULL;
> +
> + mmc_wait_for_req(mmc, &mrq);
> + kfree(data1);
> +}
> +
> +static void bht_update_cfg(struct mmc_host *mmc_host,
> + struct mmc_card *card, u32 *cfg_data, int data_len)
> +{
> + int ret = 0;
This is unused.
> + struct sdhci_host *host;
> +
> + host = mmc_priv(mmc_host);
> + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_4);
> + if (host->ops->reset)
> + host->ops->reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
> +
> + driver_send_command7(host);
> + driver_send_command24(host, cfg_data, data_len);
> + driver_send_command7(host);
> +
> + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_1);
> +}
> +
> +
[..]
> +static void bht_load_hw_inject(struct mmc_host *mmc_host,
> + struct mmc_card *card, u32 *cfg_data, int data_len,
> + u32 sel200, u32 sel100)
> +{
> + struct sdhci_host *host = mmc_priv(mmc_host);
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct sdhci_msm_bayhub_host *vendor_host =
> + sdhci_pltfm_priv(pltfm_host);
> + u32 gg_hw_inj[16] = GGC_CFG_DATA;
> +
> + gg_hw_inj[1] = 0x7364032;
> +
> + if (vendor_host->ggc.bh201_sdr104_selb_hw_inject)
> + gg_hw_inj[11] = vendor_host->ggc.bh201_sdr104_selb_hw_inject;
> + else
> + gg_hw_inj[11] = 0x57336200;
Make this the default value of bh201_sdr50_selb_hw_inject and you don't
need to make these conditionals throughout the code.
> +
> + if (vendor_host->ggc.bh201_sdr50_selb_hw_inject)
> + gg_hw_inj[12] = vendor_host->ggc.bh201_sdr50_selb_hw_inject;
> + else
> + gg_hw_inj[12] = 0x00725777;
> +
> + if (vendor_host->ggc.bh201_drive_strength)
> + gg_hw_inj[15] = vendor_host->ggc.bh201_drive_strength;
> +
> + bht_update_cfg(mmc_host, card, gg_hw_inj, data_len);
> +}
> +
[..]
> +static void sdhci_msm_bayhub_writeb(struct sdhci_host *host, u8 val, int reg)
> +{
> + u32 req_type = 0;
Don't initialize variables when the next operation on that variable is
an assignment.
> +
> + req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
> +
> + writeb_relaxed(val, host->ioaddr + reg);
> +
> + if (req_type)
> + sdhci_msm_bayhub_check_power_status(host, req_type);
> +}
[..]
> +static int sdhci_msm_bayhub_probe(struct platform_device *pdev)
> +{
[..]
> + if (of_find_property(node, "use-bayhub-bh201", NULL)) {
Why would someone use the bayhub compatible, but not have the bh201?
Isn't this a leftover from a previous version where this was a patch
ontop of sdhci-msm?
> + sdhci_bh201_parse(msm_bayhub_host->mmc);
> + INIT_DELAYED_WORK(&host->mmc->detect, mmc_rescan_bayhub);
> + } else
> + msm_bayhub_host->ggc.bh201_used = 0;
> +
Regards,
Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
* 回复: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
2021-08-20 18:20 ` Bjorn Andersson
@ 2021-08-30 12:14 ` Chevron Li (WH)
2021-11-04 6:51 ` Chevron Li (WH)
0 siblings, 1 reply; 5+ messages in thread
From: Chevron Li (WH) @ 2021-08-30 12:14 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, linux-arm-msm, linux-kernel, Shaper Liu (WH),
Xiaoguang Yu (WH), Shirley Her (SC)
Hi, Bjorn,
Thanks for your generous advice.
I have answered your questions embedded.
If there are no problem, I will come out the V2 as your advice.
Thank you for your patient again!
BR,
Chevron
> -----邮件原件-----
> 发件人: Bjorn Andersson <bjorn.andersson@linaro.org>
> 发送时间: Saturday, August 21, 2021 2:21
> 收件人: Chevron Li (WH) <chevron.li@bayhubtech.com>
> 抄送: agross@kernel.org; linux-arm-msm@vger.kernel.org; linux-
> kernel@vger.kernel.org; Shaper Liu (WH) <shaper.liu@bayhubtech.com>;
> Xiaoguang Yu (WH) <xiaoguang.yu@bayhubtech.com>; Shirley Her (SC)
> <shirley.her@bayhubtech.com>
> 主题: Re: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD
> card compatibility issue
>
> On Wed 28 Jul 10:43 PDT 2021, chevron wrote:
>
> > Improve the signal integrity for long SD bus trace by using 845+BH201
> > SD host redriver chip
> >
>
> This is a large patch with a very short commit message, which likely is the
> reason why you've not gotten any reviews.
>
Yes, I'm a freshman for the patch submission. Thanks for your patient review!
> What is this hardware? The commit message gives me a feeling that the
> BH201 is an external redriver that has been paired with the SDM845
> sometimes?
>
The hardware is GGC(chip name), and this project name is BH201.
GGC is a SD bus signal re-timing IC that has been paired with the SDM845 sometimes.
> Please describe properly how the hardware setup looks like.
>
Assign resource for GGC chip during Qualcomm host probe:
1. GGC structure initialization
2. GGC GPIO resource apply
3. Implement GGC chip special initialization function with "host->mmc_host_ops.init_card" callback.
4. Reload host->mmc->detect with GGC chip special initiation flow.
GGC chip special initiation flow match with SD spec, but not match with current SD initialization flow of Linux.
It's not necessary if we can patch the code at sd.c.
5. Reload the host->mmc_host_ops.execute_tuning with GGC chip special tuning flow.
The key points are initialized GGC chip during SD initialization and use GGC special tuning flow to re-timing SD bus signal.
>
> I did skim through the patch trying to figure out what you're doing and gave
> you some feedback below, but this is far from a complete review.
> And many of the things I point out repeats throughout the patch.
>
> I think the first step is to figure out what this is and if your design is the right
> one...
>
Yes, absolutely agree, thanks for your patient again.
The function of the patch is already verified on Chrome OS, and Google request us to submit the patch to Linux.
> > Signed-off-by: chevron.li <chevron.li@bayhubtech.com>
>
> Is your name really chevron.li? Perhaps Chevron Li?
>
Yes, thanks for your advice.
> > ---
> > change in V1:
>
> I'm not able to find v0, can you point me to it, because I would like to
> understand why these changes was made:
>
Sorry to confuse you, this patch is the first version, you can think it as V0.
> > 1. copy Qualcomm driver base from sdhci-msm.c to sdhci-bayhub.c
>
> Why do we need to duplicate all this code.
>
1. GGC is a SD bus signal re-timing IC, has no vendor ID, and need to work with sd host IC together.
2. Qualcomm engineer doesn’t allow us to add code into their source code file.
3. We will remove the unused code of Qualcomm next version.
4. We also copy some codes from core folder to implement GGC chip initialization. It matches with SD host spec, but don’t match with current sd initialazation flow.
Key points as below:
4.1 Bus width switch should at front of transfer mode switch during mode switch stage
4.2 ACMD42 should be added between Bus width switch and transfer mode switch
4.3 If above two points can be patched to sd.c directly, we can decrease much redundant code.
> > 2. implement the BH201 chip initialization function at sdhci-bayhub.c
>
> Submitting this as a large "copy sdhci-msm and implement BH201" makes it
> impossible to figure out what the BH201 specific pieces (that needs the
> review) are.
>
If we need to submit BH201 chip initialization function with an independent patch?
If yes, I will do it at next version.
> > 3. implement the BH201 chip power control function at sdhci-bayhub.c
> > 4. implement the BH201 chip tuning function at sdhci-bayhub.c 5.
> > re-implement mmc_rescan to match BH201 mode switch flow at
> > sdhci-bayhub.c
>
> If this is an external redriver, can this be paired with any other SDHCI
> controller?
>
1. GGC is a SD bus signal re-timing IC, can work with any other standard SDHCI controller to improve SD signal SI and Timing, specially used at high-speed SD mode(ex. SDR104) and long wires of SD signals.
2. We cooperated with Intel/Qualcomm/MTK/SPRD sd host already.
> > ---
> > ---
> [..]
> > diff --git a/drivers/mmc/host/sdhci-bayhub.c
> > b/drivers/mmc/host/sdhci-bayhub.c new file mode 100644 index
> > 000000000000..75029470bd22
> > --- /dev/null
> > +++ b/drivers/mmc/host/sdhci-bayhub.c
> > @@ -0,0 +1,6563 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Bayhub Technologies, Inc. BH201 SDHCI bridge IC for
> > + * VENDOR SDHCI platform driver source file
> > + *
> > + * Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > +modify
> > + * it under the terms of the GNU General Public License version 2 and
> > + * only version 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
>
> The SPDX header covers this, so don't repeat the license text here.
>
Yes, thanks for your advice.
> > + */
> > +
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/delay.h>
> > +#include <linux/mmc/mmc.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/pm_opp.h>
> > +#include <linux/slab.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/regulator/consumer.h> #include <linux/interconnect.h>
> > +#include <linux/pinctrl/consumer.h> #include <linux/mmc/host.h>
> > +#include <linux/mmc/card.h> #include <linux/mmc/sd.h> #include
> > +<linux/io.h> #include <linux/of_gpio.h>
> > +
> > +#include "sdhci-pltfm.h"
> > +#include "cqhci.h"
> > +#include "../core/core.h"
> > +#include "../core/sd_ops.h"
> > +#include "../core/sdio_ops.h"
> > +#include "../core/mmc_ops.h"
> > +#include "../core/sd.h"
> > +#include "../core/bus.h"
> > +#include "../core/host.h"
> > +#include "../core/card.h"
> > +#include "../core/pwrseq.h"
> > +
> > +#define TRUE 1
> > +#define FALSE 0
>
> Use "true" and "false"...
>
Yes, thanks for your advice.
> > +
> > +#define SD_FNC_AM_SDR50 0x2
> > +#define SD_FNC_AM_SDR104 0x3
> > +#define BIT_PASS_MASK (0x7ff)
> > +#define SDR104_MANUAL_INJECT 0x3ff
> > +#define SDR50_MANUAL_INJECT 0x77f
> > +
> [..]
> > +#define TUNING_PHASE_SIZE 11
> > +#define GGC_CFG_DATA {0x07000000, 0x07364022, 0x01015412,
> 0x01062400,\
> > + 0x10400076, 0x00025432, 0x01046076, 0x62011000,\
> > + 0x30503106, 0x64141711, 0x10057513, 0x00336200,\
> > + 0x00020006, 0x40000400, 0x12200310, 0x3A314177}
> > +
> > +struct ggc_bus_mode_cfg_t {
>
> Does "_t" say this is a struct? No need for that as "struct ggc..."
> already says "it's a struct".
>
Yes, thanks for your advice.
> > + u32 tx_selb_tb[TUNING_PHASE_SIZE];
> > + u32 all_selb_tb[TUNING_PHASE_SIZE];
> > + u32 tx_selb_failed_history;
> > + int bus_mode;
> > + int default_sela;
> > + int default_selb;
> > + u32 default_delaycode;
> > + u32 dll_voltage_unlock_cnt[4];
> > + u32 max_delaycode;
> > + u32 min_delaycode;
> > + u32 delaycode_narrowdown_index;
> > + u32 fail_phase;
> > +};
> > +
> > +enum tuning_stat_et {
>
> Does "_et" make this an enum?
Yes, will modify at next version.
>
> > + NO_TUNING = 0,
> > + OUTPUT_PASS_TYPE = 1,
> > + SET_PHASE_FAIL_TYPE = 2,
> > + TUNING_FAIL_TYPE = 3,
> > + READ_STATUS_FAIL_TYPE = 4,
> > + TUNING_CMD7_TIMEOUT = 5,
> > + RETUNING_CASE = 6,
> > +};
> > +
> > +
> > +struct t_gg_reg_strt {
>
> What is a "t gg reg strt"?
>
It means GGC register structure, use the special structure to configure GGC registers.
> > + u32 ofs;
> > + u32 mask;
> > + u32 value;
> > +};
> > +
> > +struct rl_bit_lct {
> > + u8 bits;
> > + u8 rl_bits;
> > +};
> > +
> > +struct chk_type_t {
>
> This only time this is used, it's there to pass 3 bools into a function.
> Just use function arguments.
>
Yes, thanks for your advice.
> > + u8 right_valid:1;
> > + u8 first_valid:1;
> > + u8 record_valid:1;
> > + u8 reserved:5;
> > +};
> > +
> > +static const char *const op_dbg_str[] = {
> > + "no tuning",
> > + "pass",
> > + "set_phase_fail",
> > + "tuning fail",
> > + "read status fail",
> > + "tuning CMD7 timeout",
> > + "retuning case"
> > +};
> > +
> > +struct ggc_platform_t {
>
> What is this "ggc" and what "platform" does this represent?
>
GGC is the chip IC name for BH201 project, platform means the IC related maybe can use host to replace it.
> > + struct ggc_bus_mode_cfg_t sdr50;
> > + struct ggc_bus_mode_cfg_t sdr104;
> > + struct ggc_bus_mode_cfg_t *cur_bus_mode;
> > +
> > + struct t_gg_reg_strt pha_stas_rx_low32;
> > + struct t_gg_reg_strt pha_stas_rx_high32;
> > + struct t_gg_reg_strt pha_stas_tx_low32;
> > + struct t_gg_reg_strt pha_stas_tx_high32;
> > + struct t_gg_reg_strt dll_sela_after_mask;
> > + struct t_gg_reg_strt dll_selb_after_mask;
> > +
> > + struct t_gg_reg_strt dll_delay_100m_backup;
> > + struct t_gg_reg_strt dll_delay_200m_backup;
> > +
> > + struct t_gg_reg_strt dll_sela_100m_cfg;
> > + struct t_gg_reg_strt dll_sela_200m_cfg;
> > + struct t_gg_reg_strt dll_selb_100m_cfg;
> > + struct t_gg_reg_strt dll_selb_200m_cfg;
> > + struct t_gg_reg_strt dll_selb_100m_cfg_en;
> > + struct t_gg_reg_strt dll_selb_200m_cfg_en;
> > + struct t_gg_reg_strt internl_tuning_en_100m;
> > + struct t_gg_reg_strt internl_tuning_en_200m;
> > + struct t_gg_reg_strt cmd19_cnt_cfg;
> > +
> > + struct t_gg_reg_strt inject_failure_for_tuning_enable_cfg;
> > + struct t_gg_reg_strt inject_failure_for_200m_tuning_cfg;
> > + struct t_gg_reg_strt inject_failure_for_100m_tuning_cfg;
> > +
> > + int def_sela_100m;
> > + int def_sela_200m;
> > + int def_selb_100m;
> > + int def_selb_200m;
> > +
> > + u32 _gg_reg_cur[16];
> > + u8 _cur_read_buf[512];
>
> Why does these have a '_' prefix?
>
It's no need, will modify at next version.
> > +
> > + bool dll_unlock_reinit_flg;
> > + u8 driver_strength_reinit_flg;
> > + bool tuning_cmd7_timeout_reinit_flg;
> > + u32 tuning_cmd7_timeout_reinit_cnt;
> > + u32 ggc_cur_sela;
> > + bool selx_tuning_done_flag;
> > + u32 ggc_cmd_tx_selb_failed_range;
> > + int ggc_sw_selb_tuning_first_selb;
> > + enum tuning_stat_et ggc_sela_tuning_result[11];
> > + int dll_voltage_scan_map[4];
> > + int cur_dll_voltage_idx;
> > + int sdr50_notuning_sela_inject_flag;
> > + int sdr50_notuning_crc_error_flag;
> > + u32 sdr50_notuning_sela_rx_inject;
> > + u32 bh201_sdr50_sela_sw_inject;
> > + u32 bh201_sdr50_selb_hw_inject;
> > + u32 bh201_sdr104_selb_hw_inject;
> > + u32 bh201_drive_strength;
> > + bool tuning_in_progress;
> > + int bh201_used;
> > + int pwr_gpio; /* External power enable pin for Redriver IC */
> > + int det_gpio;
> > +};
> [..]
> > +static const struct sdhci_msm_bayhub_offset
> sdhci_msm_bayhub_v5_offset = {
> > + .core_mci_data_cnt = 0x35c,
> > + .core_mci_status = 0x324,
> > + .core_mci_fifo_cnt = 0x308,
> > + .core_mci_version = 0x318,
> > + .core_generics = 0x320,
> > + .core_testbus_config = 0x32c,
> > + .core_testbus_sel2_bit = 3,
> > + .core_testbus_ena = (1 << 31),
> > + .core_testbus_sel2 = (1 << 3),
> > + .core_pwrctl_status = 0x240,
> > + .core_pwrctl_mask = 0x244,
> > + .core_pwrctl_clear = 0x248,
> > + .core_pwrctl_ctl = 0x24c,
> > + .core_sdcc_debug_reg = 0x358,
> > + .core_dll_config = 0x200,
> > + .core_dll_status = 0x208,
> > + .core_vendor_spec = 0x20c,
> > + .core_vendor_spec_adma_err_addr0 = 0x214,
> > + .core_vendor_spec_adma_err_addr1 = 0x218,
> > + .core_vendor_spec_func2 = 0x210,
> > + .core_vendor_spec_capabilities0 = 0x21c,
> > + .core_ddr_200_cfg = 0x224,
> > + .core_vendor_spec3 = 0x250,
> > + .core_dll_config_2 = 0x254,
> > + .core_dll_config_3 = 0x258,
> > + .core_ddr_config = 0x25c,
> > + .core_dll_usr_ctl = 0x388,
> > +};
> > +
> > +static const struct sdhci_msm_bayhub_offset
> > +sdhci_msm_bayhub_mci_offset = {
>
> This is unused and as such you don't need the sdhci_msm_bayhub_offset
> either.
>
Yes, will modify at next version.
> > + .core_hc_mode = 0x78,
> > + .core_mci_data_cnt = 0x30,
> > + .core_mci_status = 0x34,
> > + .core_mci_fifo_cnt = 0x44,
> > + .core_mci_version = 0x050,
> > + .core_generics = 0x70,
> > + .core_testbus_config = 0x0cc,
> > + .core_testbus_sel2_bit = 4,
> > + .core_testbus_ena = (1 << 3),
> > + .core_testbus_sel2 = (1 << 4),
> > + .core_pwrctl_status = 0xdc,
> > + .core_pwrctl_mask = 0xe0,
> > + .core_pwrctl_clear = 0xe4,
> > + .core_pwrctl_ctl = 0xe8,
> > + .core_sdcc_debug_reg = 0x124,
> > + .core_dll_config = 0x100,
> > + .core_dll_status = 0x108,
> > + .core_vendor_spec = 0x10c,
> > + .core_vendor_spec_adma_err_addr0 = 0x114,
> > + .core_vendor_spec_adma_err_addr1 = 0x118,
> > + .core_vendor_spec_func2 = 0x110,
> > + .core_vendor_spec_capabilities0 = 0x11c,
> > + .core_ddr_200_cfg = 0x184,
> > + .core_vendor_spec3 = 0x1b0,
> > + .core_dll_config_2 = 0x1b4,
> > + .core_ddr_config_old = 0x1b8,
> > + .core_ddr_config = 0x1bc,
> > +};
> > +
> [..]
> > +static const unsigned int freqs[] = { 400000, 300000, 200000, 100000
> > +};
> > +
> > +static void cfg_bit_2_bt(int max_bit, int tar, int *byt, int *bit) {
> > + struct rl_bit_lct cfg_bit_map[6] = {
> > + {0, 6}, {1, 5}, {2, 4},
> > + {3, 2}, {4, 1}, {5, 0},
> > + };
>
> So you have an array of tuples, where the first entry in the tuple is the index
> in the array? And then you only use rl_bits anyways...
>
> How about:
> u8 bit_map[6] = { 6, 5, 4, 2, 1, 0 }
>
Yes, thanks for your advice.
> > +
> > + *byt = (max_bit - tar) / 6;
> > + *bit = cfg_bit_map[(max_bit - tar) % 6].rl_bits; }
> > +
> > +static u32 cfg_read_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
> > +{
> > + u32 rv = 0;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
>
> So "bt" is short for "byte" and "bts" is "bytes"?
Yes, will use full name at next version.
>
> > + if (cfg[byt] & (1 << bit))
> > + rv |= 1 << i;
> > +
> > + i++;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
>
> There's no case where mask is 0 (and I don't see why it would be), so
>
> while (msk) {
> ...;
> msk >>= 1;
> }
>
> Seems cleaner
>
>
> But all of this would benefit from better naming and probably some
> comments describing the actual format/structure of these bits and bytes.
>
Yes, thanks for your advice.
> > + } while (1);
> > + return rv;
> > +}
> > +
> > +static void get_default_setting(struct sdhci_host *host, u8 *data) {
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > +sdhci_pltfm_priv(pltfm_host);
> > +
> > + vendor_host->ggc.def_sela_100m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_100m_cfg);
> > + vendor_host->ggc.def_sela_200m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_200m_cfg);
> > + vendor_host->ggc.def_selb_100m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_100m_cfg);
> > + vendor_host->ggc.def_selb_200m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_200m_cfg);
> > +}
> > +
> > +static void cfg_write_bits_ofs_mask(u8 *cfg,
> > + struct t_gg_reg_strt *bts, u32 w_value) {
> > + u32 wv = w_value & bts->mask;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
> > + if (wv & 1)
> > + cfg[byt] |= (u8) (1 << bit);
> > + else
> > + cfg[byt] &= (u8) (~(1 << bit));
> > +
> > + i++;
> > + wv >>= 1;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
> > + } while (1);
> > +}
> > +
> > +static void ram_bit_2_bt(int tar, int *byt, int *bit)
>
> So the "ram" variant is just a regular bitmap with 8 bits per byte?
> include/linux/bitmap.h gives your an interface for dealing with those.
>
Yes, thanks for your advice. I will check it.
> > +{
> > + *byt = tar / 8;
> > + *bit = tar % 8;
> > +}
> > +
> > +static void set_gg_reg_cur_val(struct ggc_platform_t *ggc,
> > + u8 *data, u8 len)
> > +{
> > + memcpy(&ggc->_gg_reg_cur[0], data, len); }
> > +
> > +static void get_gg_reg_cur_val(struct ggc_platform_t *ggc,
> > + u8 *data, u8 len)
> > +{
> > + memcpy(data, &ggc->_gg_reg_cur[0], len); }
> > +
> > +static void get_gg_reg_def(struct sdhci_host *host, u8 *data) {
> > + u32 gg_sw_def[16] = GGC_CFG_DATA;
> > +
> > + memcpy(data, (u8 *)&(gg_sw_def[0]), sizeof(gg_sw_def));
>
> (u8 *)&(gg_sw_def[0])... The address of the first element, type casted to a
> (u8*), then passed to a void *?
>
> Isn't that the same thing as just typing "gg_sw_def"?
>
>
> But why is GGC_CFG_DATA a define and not just a static const u32 array, in
> which case you can replace this function with just a simple memcpy in
> ggc_chip_init().
>
Yes, thanks for your advice. I will check it.
> > +}
> > +
> > +static u32 read_ram_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
> > +{
> > + u32 rv = 0;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + ram_bit_2_bt(bts->ofs + i, &byt, &bit);
> > + if (cfg[byt] & (1 << bit))
> > + rv |= 1 << i;
> > +
> > + i++;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
> > +
> > + } while (1);
> > + return rv;
> > +}
> > +
> > +static void ggc_dll_voltage_init(struct sdhci_host *host) {
> > + int i = 0;
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > +
> > + for (i = 0; i < 4; i++) {
> > + vendor_host->ggc.dll_voltage_scan_map[i] = 0;
> > + vendor_host->ggc.sdr50.dll_voltage_unlock_cnt[i] = 0;
> > + vendor_host->ggc.sdr104.dll_voltage_unlock_cnt[i] = 0;
> > + }
> > +}
> > +
> > +static void ggc_chip_init(struct sdhci_host *host) {
> > + u8 data[512] = { 0 };
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > +
> > + get_gg_reg_def(host, data);
> > + get_default_setting(host, data);
> > + set_gg_reg_cur_val(&vendor_host->ggc, data, 64); }
> > +
> > +static int driver_send_command7(struct sdhci_host *host) {
> > + int ret = 0;
> > + int err;
> > + struct mmc_host *mmc = host->mmc;
> > + struct mmc_command cmd = {0};
> > +
> > + cmd.opcode = MMC_SELECT_CARD;
> > + cmd.arg = 0;
> > + cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
> > + err = mmc_wait_for_cmd(mmc, &cmd, 3);
> > + if (err)
> > + ret = 0;
> > + else
> > + ret = 1;
> > +
> > + return ret;
>
> return mmc_wait_for_cmd() seems more reasonable, but you don't check
> the return value in any off the call sites...
>
Yes, thanks for your advice. I will check it.
> > +}
> > +
> > +static void driver_send_command24(struct sdhci_host *host,
> > + u32 *cfg_data, int data_len)
> > +{
> > + struct mmc_host *mmc = host->mmc;
> > + struct mmc_request mrq = {0};
> > + struct mmc_command cmd = { 0 };
> > + struct mmc_data data = { 0 };
> > + struct scatterlist sg;
> > + u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
>
> This allocation needs a NULL check.
>
Yes, thanks for your advice.
> > +
> > + memcpy(data1, (u8 *)&(cfg_data[0]), data_len);
> > + sg_init_one(&sg, data1, 512);
> > +
> > + cmd.opcode = MMC_WRITE_BLOCK;
> > + cmd.arg = 0;
> > + cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
> > + data.blksz = 512;
> > + data.blocks = 1;
> > + data.flags = MMC_DATA_WRITE;
> > + data.timeout_ns = 1000 * 1000 * 1000;
> > + data.sg = &sg;
> > + data.sg_len = 1;
> > + mrq.cmd = &cmd;
> > + mrq.data = &data;
> > + mrq.stop = NULL;
> > +
> > + mmc_wait_for_req(mmc, &mrq);
> > + kfree(data1);
> > +}
> > +
> > +static void bht_update_cfg(struct mmc_host *mmc_host,
> > + struct mmc_card *card, u32 *cfg_data, int data_len) {
> > + int ret = 0;
>
> This is unused.
>
Yes, will remove it next version.
> > + struct sdhci_host *host;
> > +
> > + host = mmc_priv(mmc_host);
> > + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_4);
> > + if (host->ops->reset)
> > + host->ops->reset(host,
> SDHCI_RESET_CMD|SDHCI_RESET_DATA);
> > +
> > + driver_send_command7(host);
> > + driver_send_command24(host, cfg_data, data_len);
> > + driver_send_command7(host);
> > +
> > + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_1); }
> > +
> > +
> [..]
> > +static void bht_load_hw_inject(struct mmc_host *mmc_host,
> > + struct mmc_card *card, u32 *cfg_data, int data_len,
> > + u32 sel200, u32 sel100)
> > +{
> > + struct sdhci_host *host = mmc_priv(mmc_host);
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > + u32 gg_hw_inj[16] = GGC_CFG_DATA;
> > +
> > + gg_hw_inj[1] = 0x7364032;
> > +
> > + if (vendor_host->ggc.bh201_sdr104_selb_hw_inject)
> > + gg_hw_inj[11] = vendor_host-
> >ggc.bh201_sdr104_selb_hw_inject;
> > + else
> > + gg_hw_inj[11] = 0x57336200;
>
> Make this the default value of bh201_sdr50_selb_hw_inject and you don't
> need to make these conditionals throughout the code.
>
Yes, thanks for your advice.
> > +
> > + if (vendor_host->ggc.bh201_sdr50_selb_hw_inject)
> > + gg_hw_inj[12] = vendor_host-
> >ggc.bh201_sdr50_selb_hw_inject;
> > + else
> > + gg_hw_inj[12] = 0x00725777;
> > +
> > + if (vendor_host->ggc.bh201_drive_strength)
> > + gg_hw_inj[15] = vendor_host->ggc.bh201_drive_strength;
> > +
> > + bht_update_cfg(mmc_host, card, gg_hw_inj, data_len); }
> > +
> [..]
> > +static void sdhci_msm_bayhub_writeb(struct sdhci_host *host, u8 val,
> > +int reg) {
> > + u32 req_type = 0;
>
> Don't initialize variables when the next operation on that variable is an
> assignment.
>
Yes, thanks for your advice.
> > +
> > + req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
> > +
> > + writeb_relaxed(val, host->ioaddr + reg);
> > +
> > + if (req_type)
> > + sdhci_msm_bayhub_check_power_status(host, req_type); }
> [..]
> > +static int sdhci_msm_bayhub_probe(struct platform_device *pdev) {
> [..]
> > + if (of_find_property(node, "use-bayhub-bh201", NULL)) {
>
> Why would someone use the bayhub compatible, but not have the bh201?
>
> Isn't this a leftover from a previous version where this was a patch ontop of
> sdhci-msm?
>
Yes, you are right, will modify it at next version.
> > + sdhci_bh201_parse(msm_bayhub_host->mmc);
> > + INIT_DELAYED_WORK(&host->mmc->detect,
> mmc_rescan_bayhub);
> > + } else
> > + msm_bayhub_host->ggc.bh201_used = 0;
> > +
>
> Regards,
> Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
* 回复: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
2021-08-30 12:14 ` 回复: " Chevron Li (WH)
@ 2021-11-04 6:51 ` Chevron Li (WH)
0 siblings, 0 replies; 5+ messages in thread
From: Chevron Li (WH) @ 2021-11-04 6:51 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, linux-arm-msm, linux-kernel, Shaper Liu (WH),
XiaoGuang Yu (WH), Shirley Her(SC)
Hi, Bjorn,
Excuse me.
Have you checked our feedback yet?
If there are other points need to be noticed at V2 besides your advice?
Look forward to your reply.
BR,
Chevron
-----邮件原件-----
发件人: Chevron Li (WH)
发送时间: Monday, August 30, 2021 20:15
收件人: Bjorn Andersson <bjorn.andersson@linaro.org>
抄送: agross@kernel.org; linux-arm-msm@vger.kernel.org; linux-kernel@vger.kernel.org; Shaper Liu (WH) <shaper.liu@bayhubtech.com>; Xiaoguang Yu (WH) <xiaoguang.yu@bayhubtech.com>; Shirley Her (SC) <shirley.her@bayhubtech.com>
主题: 回复: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
Hi, Bjorn,
Thanks for your generous advice.
I have answered your questions embedded.
If there are no problem, I will come out the V2 as your advice.
Thank you for your patient again!
BR,
Chevron
> -----邮件原件-----
> 发件人: Bjorn Andersson <bjorn.andersson@linaro.org>
> 发送时间: Saturday, August 21, 2021 2:21
> 收件人: Chevron Li (WH) <chevron.li@bayhubtech.com>
> 抄送: agross@kernel.org; linux-arm-msm@vger.kernel.org; linux-
> kernel@vger.kernel.org; Shaper Liu (WH) <shaper.liu@bayhubtech.com>;
> Xiaoguang Yu (WH) <xiaoguang.yu@bayhubtech.com>; Shirley Her (SC)
> <shirley.her@bayhubtech.com>
> 主题: Re: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD
> card compatibility issue
>
> On Wed 28 Jul 10:43 PDT 2021, chevron wrote:
>
> > Improve the signal integrity for long SD bus trace by using
> > 845+BH201 SD host redriver chip
> >
>
> This is a large patch with a very short commit message, which likely
> is the reason why you've not gotten any reviews.
>
Yes, I'm a freshman for the patch submission. Thanks for your patient review!
> What is this hardware? The commit message gives me a feeling that the
> BH201 is an external redriver that has been paired with the SDM845
> sometimes?
>
The hardware is GGC(chip name), and this project name is BH201.
GGC is a SD bus signal re-timing IC that has been paired with the SDM845 sometimes.
> Please describe properly how the hardware setup looks like.
>
Assign resource for GGC chip during Qualcomm host probe:
1. GGC structure initialization
2. GGC GPIO resource apply
3. Implement GGC chip special initialization function with "host->mmc_host_ops.init_card" callback.
4. Reload host->mmc->detect with GGC chip special initiation flow.
GGC chip special initiation flow match with SD spec, but not match with current SD initialization flow of Linux.
It's not necessary if we can patch the code at sd.c.
5. Reload the host->mmc_host_ops.execute_tuning with GGC chip special tuning flow.
The key points are initialized GGC chip during SD initialization and use GGC special tuning flow to re-timing SD bus signal.
>
> I did skim through the patch trying to figure out what you're doing
> and gave you some feedback below, but this is far from a complete review.
> And many of the things I point out repeats throughout the patch.
>
> I think the first step is to figure out what this is and if your
> design is the right one...
>
Yes, absolutely agree, thanks for your patient again.
The function of the patch is already verified on Chrome OS, and Google request us to submit the patch to Linux.
> > Signed-off-by: chevron.li <chevron.li@bayhubtech.com>
>
> Is your name really chevron.li? Perhaps Chevron Li?
>
Yes, thanks for your advice.
> > ---
> > change in V1:
>
> I'm not able to find v0, can you point me to it, because I would like
> to understand why these changes was made:
>
Sorry to confuse you, this patch is the first version, you can think it as V0.
> > 1. copy Qualcomm driver base from sdhci-msm.c to sdhci-bayhub.c
>
> Why do we need to duplicate all this code.
>
1. GGC is a SD bus signal re-timing IC, has no vendor ID, and need to work with sd host IC together.
2. Qualcomm engineer doesn’t allow us to add code into their source code file.
3. We will remove the unused code of Qualcomm next version.
4. We also copy some codes from core folder to implement GGC chip initialization. It matches with SD host spec, but don’t match with current sd initialazation flow.
Key points as below:
4.1 Bus width switch should at front of transfer mode switch during mode switch stage
4.2 ACMD42 should be added between Bus width switch and transfer mode switch
4.3 If above two points can be patched to sd.c directly, we can decrease much redundant code.
> > 2. implement the BH201 chip initialization function at
> > sdhci-bayhub.c
>
> Submitting this as a large "copy sdhci-msm and implement BH201" makes
> it impossible to figure out what the BH201 specific pieces (that needs
> the
> review) are.
>
If we need to submit BH201 chip initialization function with an independent patch?
If yes, I will do it at next version.
> > 3. implement the BH201 chip power control function at sdhci-bayhub.c
> > 4. implement the BH201 chip tuning function at sdhci-bayhub.c 5.
> > re-implement mmc_rescan to match BH201 mode switch flow at
> > sdhci-bayhub.c
>
> If this is an external redriver, can this be paired with any other
> SDHCI controller?
>
1. GGC is a SD bus signal re-timing IC, can work with any other standard SDHCI controller to improve SD signal SI and Timing, specially used at high-speed SD mode(ex. SDR104) and long wires of SD signals.
2. We cooperated with Intel/Qualcomm/MTK/SPRD sd host already.
> > ---
> > ---
> [..]
> > diff --git a/drivers/mmc/host/sdhci-bayhub.c
> > b/drivers/mmc/host/sdhci-bayhub.c new file mode 100644 index
> > 000000000000..75029470bd22
> > --- /dev/null
> > +++ b/drivers/mmc/host/sdhci-bayhub.c
> > @@ -0,0 +1,6563 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Bayhub Technologies, Inc. BH201 SDHCI bridge IC for
> > + * VENDOR SDHCI platform driver source file
> > + *
> > + * Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > +modify
> > + * it under the terms of the GNU General Public License version 2
> > +and
> > + * only version 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
>
> The SPDX header covers this, so don't repeat the license text here.
>
Yes, thanks for your advice.
> > + */
> > +
> > +#include <linux/module.h>
> > +#include <linux/of_device.h>
> > +#include <linux/delay.h>
> > +#include <linux/mmc/mmc.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/pm_opp.h>
> > +#include <linux/slab.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/regulator/consumer.h> #include
> > +<linux/interconnect.h> #include <linux/pinctrl/consumer.h> #include
> > +<linux/mmc/host.h> #include <linux/mmc/card.h> #include
> > +<linux/mmc/sd.h> #include <linux/io.h> #include <linux/of_gpio.h>
> > +
> > +#include "sdhci-pltfm.h"
> > +#include "cqhci.h"
> > +#include "../core/core.h"
> > +#include "../core/sd_ops.h"
> > +#include "../core/sdio_ops.h"
> > +#include "../core/mmc_ops.h"
> > +#include "../core/sd.h"
> > +#include "../core/bus.h"
> > +#include "../core/host.h"
> > +#include "../core/card.h"
> > +#include "../core/pwrseq.h"
> > +
> > +#define TRUE 1
> > +#define FALSE 0
>
> Use "true" and "false"...
>
Yes, thanks for your advice.
> > +
> > +#define SD_FNC_AM_SDR50 0x2
> > +#define SD_FNC_AM_SDR104 0x3
> > +#define BIT_PASS_MASK (0x7ff)
> > +#define SDR104_MANUAL_INJECT 0x3ff
> > +#define SDR50_MANUAL_INJECT 0x77f
> > +
> [..]
> > +#define TUNING_PHASE_SIZE 11
> > +#define GGC_CFG_DATA {0x07000000, 0x07364022, 0x01015412,
> 0x01062400,\
> > + 0x10400076, 0x00025432, 0x01046076, 0x62011000,\
> > + 0x30503106, 0x64141711, 0x10057513, 0x00336200,\
> > + 0x00020006, 0x40000400, 0x12200310, 0x3A314177}
> > +
> > +struct ggc_bus_mode_cfg_t {
>
> Does "_t" say this is a struct? No need for that as "struct ggc..."
> already says "it's a struct".
>
Yes, thanks for your advice.
> > + u32 tx_selb_tb[TUNING_PHASE_SIZE];
> > + u32 all_selb_tb[TUNING_PHASE_SIZE];
> > + u32 tx_selb_failed_history;
> > + int bus_mode;
> > + int default_sela;
> > + int default_selb;
> > + u32 default_delaycode;
> > + u32 dll_voltage_unlock_cnt[4];
> > + u32 max_delaycode;
> > + u32 min_delaycode;
> > + u32 delaycode_narrowdown_index;
> > + u32 fail_phase;
> > +};
> > +
> > +enum tuning_stat_et {
>
> Does "_et" make this an enum?
Yes, will modify at next version.
>
> > + NO_TUNING = 0,
> > + OUTPUT_PASS_TYPE = 1,
> > + SET_PHASE_FAIL_TYPE = 2,
> > + TUNING_FAIL_TYPE = 3,
> > + READ_STATUS_FAIL_TYPE = 4,
> > + TUNING_CMD7_TIMEOUT = 5,
> > + RETUNING_CASE = 6,
> > +};
> > +
> > +
> > +struct t_gg_reg_strt {
>
> What is a "t gg reg strt"?
>
It means GGC register structure, use the special structure to configure GGC registers.
> > + u32 ofs;
> > + u32 mask;
> > + u32 value;
> > +};
> > +
> > +struct rl_bit_lct {
> > + u8 bits;
> > + u8 rl_bits;
> > +};
> > +
> > +struct chk_type_t {
>
> This only time this is used, it's there to pass 3 bools into a function.
> Just use function arguments.
>
Yes, thanks for your advice.
> > + u8 right_valid:1;
> > + u8 first_valid:1;
> > + u8 record_valid:1;
> > + u8 reserved:5;
> > +};
> > +
> > +static const char *const op_dbg_str[] = {
> > + "no tuning",
> > + "pass",
> > + "set_phase_fail",
> > + "tuning fail",
> > + "read status fail",
> > + "tuning CMD7 timeout",
> > + "retuning case"
> > +};
> > +
> > +struct ggc_platform_t {
>
> What is this "ggc" and what "platform" does this represent?
>
GGC is the chip IC name for BH201 project, platform means the IC related maybe can use host to replace it.
> > + struct ggc_bus_mode_cfg_t sdr50;
> > + struct ggc_bus_mode_cfg_t sdr104;
> > + struct ggc_bus_mode_cfg_t *cur_bus_mode;
> > +
> > + struct t_gg_reg_strt pha_stas_rx_low32;
> > + struct t_gg_reg_strt pha_stas_rx_high32;
> > + struct t_gg_reg_strt pha_stas_tx_low32;
> > + struct t_gg_reg_strt pha_stas_tx_high32;
> > + struct t_gg_reg_strt dll_sela_after_mask;
> > + struct t_gg_reg_strt dll_selb_after_mask;
> > +
> > + struct t_gg_reg_strt dll_delay_100m_backup;
> > + struct t_gg_reg_strt dll_delay_200m_backup;
> > +
> > + struct t_gg_reg_strt dll_sela_100m_cfg;
> > + struct t_gg_reg_strt dll_sela_200m_cfg;
> > + struct t_gg_reg_strt dll_selb_100m_cfg;
> > + struct t_gg_reg_strt dll_selb_200m_cfg;
> > + struct t_gg_reg_strt dll_selb_100m_cfg_en;
> > + struct t_gg_reg_strt dll_selb_200m_cfg_en;
> > + struct t_gg_reg_strt internl_tuning_en_100m;
> > + struct t_gg_reg_strt internl_tuning_en_200m;
> > + struct t_gg_reg_strt cmd19_cnt_cfg;
> > +
> > + struct t_gg_reg_strt inject_failure_for_tuning_enable_cfg;
> > + struct t_gg_reg_strt inject_failure_for_200m_tuning_cfg;
> > + struct t_gg_reg_strt inject_failure_for_100m_tuning_cfg;
> > +
> > + int def_sela_100m;
> > + int def_sela_200m;
> > + int def_selb_100m;
> > + int def_selb_200m;
> > +
> > + u32 _gg_reg_cur[16];
> > + u8 _cur_read_buf[512];
>
> Why does these have a '_' prefix?
>
It's no need, will modify at next version.
> > +
> > + bool dll_unlock_reinit_flg;
> > + u8 driver_strength_reinit_flg;
> > + bool tuning_cmd7_timeout_reinit_flg;
> > + u32 tuning_cmd7_timeout_reinit_cnt;
> > + u32 ggc_cur_sela;
> > + bool selx_tuning_done_flag;
> > + u32 ggc_cmd_tx_selb_failed_range;
> > + int ggc_sw_selb_tuning_first_selb;
> > + enum tuning_stat_et ggc_sela_tuning_result[11];
> > + int dll_voltage_scan_map[4];
> > + int cur_dll_voltage_idx;
> > + int sdr50_notuning_sela_inject_flag;
> > + int sdr50_notuning_crc_error_flag;
> > + u32 sdr50_notuning_sela_rx_inject;
> > + u32 bh201_sdr50_sela_sw_inject;
> > + u32 bh201_sdr50_selb_hw_inject;
> > + u32 bh201_sdr104_selb_hw_inject;
> > + u32 bh201_drive_strength;
> > + bool tuning_in_progress;
> > + int bh201_used;
> > + int pwr_gpio; /* External power enable pin for Redriver IC */
> > + int det_gpio;
> > +};
> [..]
> > +static const struct sdhci_msm_bayhub_offset
> sdhci_msm_bayhub_v5_offset = {
> > + .core_mci_data_cnt = 0x35c,
> > + .core_mci_status = 0x324,
> > + .core_mci_fifo_cnt = 0x308,
> > + .core_mci_version = 0x318,
> > + .core_generics = 0x320,
> > + .core_testbus_config = 0x32c,
> > + .core_testbus_sel2_bit = 3,
> > + .core_testbus_ena = (1 << 31),
> > + .core_testbus_sel2 = (1 << 3),
> > + .core_pwrctl_status = 0x240,
> > + .core_pwrctl_mask = 0x244,
> > + .core_pwrctl_clear = 0x248,
> > + .core_pwrctl_ctl = 0x24c,
> > + .core_sdcc_debug_reg = 0x358,
> > + .core_dll_config = 0x200,
> > + .core_dll_status = 0x208,
> > + .core_vendor_spec = 0x20c,
> > + .core_vendor_spec_adma_err_addr0 = 0x214,
> > + .core_vendor_spec_adma_err_addr1 = 0x218,
> > + .core_vendor_spec_func2 = 0x210,
> > + .core_vendor_spec_capabilities0 = 0x21c,
> > + .core_ddr_200_cfg = 0x224,
> > + .core_vendor_spec3 = 0x250,
> > + .core_dll_config_2 = 0x254,
> > + .core_dll_config_3 = 0x258,
> > + .core_ddr_config = 0x25c,
> > + .core_dll_usr_ctl = 0x388,
> > +};
> > +
> > +static const struct sdhci_msm_bayhub_offset
> > +sdhci_msm_bayhub_mci_offset = {
>
> This is unused and as such you don't need the sdhci_msm_bayhub_offset
> either.
>
Yes, will modify at next version.
> > + .core_hc_mode = 0x78,
> > + .core_mci_data_cnt = 0x30,
> > + .core_mci_status = 0x34,
> > + .core_mci_fifo_cnt = 0x44,
> > + .core_mci_version = 0x050,
> > + .core_generics = 0x70,
> > + .core_testbus_config = 0x0cc,
> > + .core_testbus_sel2_bit = 4,
> > + .core_testbus_ena = (1 << 3),
> > + .core_testbus_sel2 = (1 << 4),
> > + .core_pwrctl_status = 0xdc,
> > + .core_pwrctl_mask = 0xe0,
> > + .core_pwrctl_clear = 0xe4,
> > + .core_pwrctl_ctl = 0xe8,
> > + .core_sdcc_debug_reg = 0x124,
> > + .core_dll_config = 0x100,
> > + .core_dll_status = 0x108,
> > + .core_vendor_spec = 0x10c,
> > + .core_vendor_spec_adma_err_addr0 = 0x114,
> > + .core_vendor_spec_adma_err_addr1 = 0x118,
> > + .core_vendor_spec_func2 = 0x110,
> > + .core_vendor_spec_capabilities0 = 0x11c,
> > + .core_ddr_200_cfg = 0x184,
> > + .core_vendor_spec3 = 0x1b0,
> > + .core_dll_config_2 = 0x1b4,
> > + .core_ddr_config_old = 0x1b8,
> > + .core_ddr_config = 0x1bc,
> > +};
> > +
> [..]
> > +static const unsigned int freqs[] = { 400000, 300000, 200000,
> > +100000 };
> > +
> > +static void cfg_bit_2_bt(int max_bit, int tar, int *byt, int *bit) {
> > + struct rl_bit_lct cfg_bit_map[6] = {
> > + {0, 6}, {1, 5}, {2, 4},
> > + {3, 2}, {4, 1}, {5, 0},
> > + };
>
> So you have an array of tuples, where the first entry in the tuple is
> the index in the array? And then you only use rl_bits anyways...
>
> How about:
> u8 bit_map[6] = { 6, 5, 4, 2, 1, 0 }
>
Yes, thanks for your advice.
> > +
> > + *byt = (max_bit - tar) / 6;
> > + *bit = cfg_bit_map[(max_bit - tar) % 6].rl_bits; }
> > +
> > +static u32 cfg_read_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt
> > +*bts) {
> > + u32 rv = 0;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
>
> So "bt" is short for "byte" and "bts" is "bytes"?
Yes, will use full name at next version.
>
> > + if (cfg[byt] & (1 << bit))
> > + rv |= 1 << i;
> > +
> > + i++;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
>
> There's no case where mask is 0 (and I don't see why it would be), so
>
> while (msk) {
> ...;
> msk >>= 1;
> }
>
> Seems cleaner
>
>
> But all of this would benefit from better naming and probably some
> comments describing the actual format/structure of these bits and bytes.
>
Yes, thanks for your advice.
> > + } while (1);
> > + return rv;
> > +}
> > +
> > +static void get_default_setting(struct sdhci_host *host, u8 *data) {
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > +sdhci_pltfm_priv(pltfm_host);
> > +
> > + vendor_host->ggc.def_sela_100m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_100m_cfg);
> > + vendor_host->ggc.def_sela_200m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_200m_cfg);
> > + vendor_host->ggc.def_selb_100m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_100m_cfg);
> > + vendor_host->ggc.def_selb_200m =
> > + cfg_read_bits_ofs_mask(data, &vendor_host-
> >ggc.dll_sela_200m_cfg);
> > +}
> > +
> > +static void cfg_write_bits_ofs_mask(u8 *cfg,
> > + struct t_gg_reg_strt *bts, u32 w_value) {
> > + u32 wv = w_value & bts->mask;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
> > + if (wv & 1)
> > + cfg[byt] |= (u8) (1 << bit);
> > + else
> > + cfg[byt] &= (u8) (~(1 << bit));
> > +
> > + i++;
> > + wv >>= 1;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
> > + } while (1);
> > +}
> > +
> > +static void ram_bit_2_bt(int tar, int *byt, int *bit)
>
> So the "ram" variant is just a regular bitmap with 8 bits per byte?
> include/linux/bitmap.h gives your an interface for dealing with those.
>
Yes, thanks for your advice. I will check it.
> > +{
> > + *byt = tar / 8;
> > + *bit = tar % 8;
> > +}
> > +
> > +static void set_gg_reg_cur_val(struct ggc_platform_t *ggc,
> > + u8 *data, u8 len)
> > +{
> > + memcpy(&ggc->_gg_reg_cur[0], data, len); }
> > +
> > +static void get_gg_reg_cur_val(struct ggc_platform_t *ggc,
> > + u8 *data, u8 len)
> > +{
> > + memcpy(data, &ggc->_gg_reg_cur[0], len); }
> > +
> > +static void get_gg_reg_def(struct sdhci_host *host, u8 *data) {
> > + u32 gg_sw_def[16] = GGC_CFG_DATA;
> > +
> > + memcpy(data, (u8 *)&(gg_sw_def[0]), sizeof(gg_sw_def));
>
> (u8 *)&(gg_sw_def[0])... The address of the first element, type casted
> to a (u8*), then passed to a void *?
>
> Isn't that the same thing as just typing "gg_sw_def"?
>
>
> But why is GGC_CFG_DATA a define and not just a static const u32
> array, in which case you can replace this function with just a simple
> memcpy in ggc_chip_init().
>
Yes, thanks for your advice. I will check it.
> > +}
> > +
> > +static u32 read_ram_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt
> > +*bts) {
> > + u32 rv = 0;
> > + u32 msk = bts->mask;
> > + int byt = 0, bit = 0;
> > + int i = 0;
> > +
> > + do {
> > + ram_bit_2_bt(bts->ofs + i, &byt, &bit);
> > + if (cfg[byt] & (1 << bit))
> > + rv |= 1 << i;
> > +
> > + i++;
> > + msk >>= 1;
> > + if (msk == 0)
> > + break;
> > +
> > + } while (1);
> > + return rv;
> > +}
> > +
> > +static void ggc_dll_voltage_init(struct sdhci_host *host) {
> > + int i = 0;
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > +
> > + for (i = 0; i < 4; i++) {
> > + vendor_host->ggc.dll_voltage_scan_map[i] = 0;
> > + vendor_host->ggc.sdr50.dll_voltage_unlock_cnt[i] = 0;
> > + vendor_host->ggc.sdr104.dll_voltage_unlock_cnt[i] = 0;
> > + }
> > +}
> > +
> > +static void ggc_chip_init(struct sdhci_host *host) {
> > + u8 data[512] = { 0 };
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > +
> > + get_gg_reg_def(host, data);
> > + get_default_setting(host, data);
> > + set_gg_reg_cur_val(&vendor_host->ggc, data, 64); }
> > +
> > +static int driver_send_command7(struct sdhci_host *host) {
> > + int ret = 0;
> > + int err;
> > + struct mmc_host *mmc = host->mmc;
> > + struct mmc_command cmd = {0};
> > +
> > + cmd.opcode = MMC_SELECT_CARD;
> > + cmd.arg = 0;
> > + cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
> > + err = mmc_wait_for_cmd(mmc, &cmd, 3);
> > + if (err)
> > + ret = 0;
> > + else
> > + ret = 1;
> > +
> > + return ret;
>
> return mmc_wait_for_cmd() seems more reasonable, but you don't check
> the return value in any off the call sites...
>
Yes, thanks for your advice. I will check it.
> > +}
> > +
> > +static void driver_send_command24(struct sdhci_host *host,
> > + u32 *cfg_data, int data_len)
> > +{
> > + struct mmc_host *mmc = host->mmc;
> > + struct mmc_request mrq = {0};
> > + struct mmc_command cmd = { 0 };
> > + struct mmc_data data = { 0 };
> > + struct scatterlist sg;
> > + u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
>
> This allocation needs a NULL check.
>
Yes, thanks for your advice.
> > +
> > + memcpy(data1, (u8 *)&(cfg_data[0]), data_len);
> > + sg_init_one(&sg, data1, 512);
> > +
> > + cmd.opcode = MMC_WRITE_BLOCK;
> > + cmd.arg = 0;
> > + cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
> > + data.blksz = 512;
> > + data.blocks = 1;
> > + data.flags = MMC_DATA_WRITE;
> > + data.timeout_ns = 1000 * 1000 * 1000;
> > + data.sg = &sg;
> > + data.sg_len = 1;
> > + mrq.cmd = &cmd;
> > + mrq.data = &data;
> > + mrq.stop = NULL;
> > +
> > + mmc_wait_for_req(mmc, &mrq);
> > + kfree(data1);
> > +}
> > +
> > +static void bht_update_cfg(struct mmc_host *mmc_host,
> > + struct mmc_card *card, u32 *cfg_data, int data_len) {
> > + int ret = 0;
>
> This is unused.
>
Yes, will remove it next version.
> > + struct sdhci_host *host;
> > +
> > + host = mmc_priv(mmc_host);
> > + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_4);
> > + if (host->ops->reset)
> > + host->ops->reset(host,
> SDHCI_RESET_CMD|SDHCI_RESET_DATA);
> > +
> > + driver_send_command7(host);
> > + driver_send_command24(host, cfg_data, data_len);
> > + driver_send_command7(host);
> > +
> > + mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_1); }
> > +
> > +
> [..]
> > +static void bht_load_hw_inject(struct mmc_host *mmc_host,
> > + struct mmc_card *card, u32 *cfg_data, int data_len,
> > + u32 sel200, u32 sel100)
> > +{
> > + struct sdhci_host *host = mmc_priv(mmc_host);
> > + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> > + struct sdhci_msm_bayhub_host *vendor_host =
> > + sdhci_pltfm_priv(pltfm_host);
> > + u32 gg_hw_inj[16] = GGC_CFG_DATA;
> > +
> > + gg_hw_inj[1] = 0x7364032;
> > +
> > + if (vendor_host->ggc.bh201_sdr104_selb_hw_inject)
> > + gg_hw_inj[11] = vendor_host-
> >ggc.bh201_sdr104_selb_hw_inject;
> > + else
> > + gg_hw_inj[11] = 0x57336200;
>
> Make this the default value of bh201_sdr50_selb_hw_inject and you
> don't need to make these conditionals throughout the code.
>
Yes, thanks for your advice.
> > +
> > + if (vendor_host->ggc.bh201_sdr50_selb_hw_inject)
> > + gg_hw_inj[12] = vendor_host-
> >ggc.bh201_sdr50_selb_hw_inject;
> > + else
> > + gg_hw_inj[12] = 0x00725777;
> > +
> > + if (vendor_host->ggc.bh201_drive_strength)
> > + gg_hw_inj[15] = vendor_host->ggc.bh201_drive_strength;
> > +
> > + bht_update_cfg(mmc_host, card, gg_hw_inj, data_len); }
> > +
> [..]
> > +static void sdhci_msm_bayhub_writeb(struct sdhci_host *host, u8
> > +val, int reg) {
> > + u32 req_type = 0;
>
> Don't initialize variables when the next operation on that variable is
> an assignment.
>
Yes, thanks for your advice.
> > +
> > + req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
> > +
> > + writeb_relaxed(val, host->ioaddr + reg);
> > +
> > + if (req_type)
> > + sdhci_msm_bayhub_check_power_status(host, req_type); }
> [..]
> > +static int sdhci_msm_bayhub_probe(struct platform_device *pdev) {
> [..]
> > + if (of_find_property(node, "use-bayhub-bh201", NULL)) {
>
> Why would someone use the bayhub compatible, but not have the bh201?
>
> Isn't this a leftover from a previous version where this was a patch
> ontop of sdhci-msm?
>
Yes, you are right, will modify it at next version.
> > + sdhci_bh201_parse(msm_bayhub_host->mmc);
> > + INIT_DELAYED_WORK(&host->mmc->detect,
> mmc_rescan_bayhub);
> > + } else
> > + msm_bayhub_host->ggc.bh201_used = 0;
> > +
>
> Regards,
> Bjorn
^ permalink raw reply [flat|nested] 5+ messages in thread
* 回复: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
[not found] <20210714010742.4707-1-chevron.li@bayhubtech.com>
@ 2021-07-20 11:43 ` Chevron Li (WH)
0 siblings, 0 replies; 5+ messages in thread
From: Chevron Li (WH) @ 2021-07-20 11:43 UTC (permalink / raw)
To: adrian.hunter, ulf.hansson, linux-mmc, linux-kernel
Cc: Shaper Liu (WH), Xiaoguang Yu (WH), Shirley Her (SC)
Hi, Adrian&Ulf,
Can you give some comments for this patch?
Your suggestion is important for us.
We look forward to hearing from you.
-----邮件原件-----
发件人: Chevron Li (WH) <chevron.li@bayhubtech.com>
发送时间: Wednesday, July 14, 2021 9:08 AM
收件人: adrian.hunter@intel.com; ulf.hansson@linaro.org; linux-mmc@vger.kernel.org; linux.kernel@vger.kernel.org
抄送: Shaper Liu (WH) <shaper.liu@bayhubtech.com>; Chevron Li (WH) <chevron.li@bayhubtech.com>; Xiaoguang Yu (WH) <xiaoguang.yu@bayhubtech.com>; Shirley Her (SC) <shirley.her@bayhubtech.com>
主题: [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue
Improve the signal integrity for long SD bus trace by using 845+BH201 SD host redriver chip
Signed-off-by: chevron.li <chevron.li@bayhubtech.com>
---
change in V1:
1. copy Qualcomm driver base from sdhci-msm.c to sdhci-bayhub.c
2. implement the BH201 chip initialization function at sdhci-bayhub.c
3. implement the BH201 chip power control function at sdhci-bayhub.c
4. implement the BH201 chip tuning function at sdhci-bayhub.c
5. re-implement mmc_rescan to match BH201 mode switch flow at sdhci-bayhub.c
---
---
.../devicetree/bindings/mmc/sdhci-msm.txt | 1 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-bayhub.c | 6563 +++++++++++++++++
3 files changed, 6565 insertions(+)
create mode 100644 drivers/mmc/host/sdhci-bayhub.c
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
index 4c7fa6a4ed15..a0401dc16929 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.txt
@@ -20,6 +20,7 @@ Required properties:
"qcom,qcs404-sdhci", "qcom,sdhci-msm-v5"
"qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
"qcom,sdm845-sdhci", "qcom,sdhci-msm-v5"
+ "qcom,sdm845-bayhub-sdhci", "qcom,sdhci-msm-bayhub-v5"
"qcom,sdx55-sdhci", "qcom,sdhci-msm-v5";
"qcom,sm8250-sdhci", "qcom,sdhci-msm-v5"
NOTE that some old device tree files may be floating around that only
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 14004cc09aaa..d4d6f4cca732 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_MMC_SDHCI_OF_SPARX5) += sdhci-of-sparx5.o
obj-$(CONFIG_MMC_SDHCI_BCM_KONA) += sdhci-bcm-kona.o
obj-$(CONFIG_MMC_SDHCI_IPROC) += sdhci-iproc.o
obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-msm.o
+obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-bayhub.o
obj-$(CONFIG_MMC_SDHCI_ST) += sdhci-st.o
obj-$(CONFIG_MMC_SDHCI_MICROCHIP_PIC32) += sdhci-pic32.o
obj-$(CONFIG_MMC_SDHCI_BRCMSTB) += sdhci-brcmstb.o
diff --git a/drivers/mmc/host/sdhci-bayhub.c b/drivers/mmc/host/sdhci-bayhub.c
new file mode 100644
index 000000000000..75029470bd22
--- /dev/null
+++ b/drivers/mmc/host/sdhci-bayhub.c
@@ -0,0 +1,6563 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Bayhub Technologies, Inc. BH201 SDHCI bridge IC for
+ * VENDOR SDHCI platform driver source file
+ *
+ * Copyright (c) 2012-2018, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/delay.h>
+#include <linux/mmc/mmc.h>
+#include <linux/pm_runtime.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/iopoll.h>
+#include <linux/regulator/consumer.h>
+#include <linux/interconnect.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/sd.h>
+#include <linux/io.h>
+#include <linux/of_gpio.h>
+
+#include "sdhci-pltfm.h"
+#include "cqhci.h"
+#include "../core/core.h"
+#include "../core/sd_ops.h"
+#include "../core/sdio_ops.h"
+#include "../core/mmc_ops.h"
+#include "../core/sd.h"
+#include "../core/bus.h"
+#include "../core/host.h"
+#include "../core/card.h"
+#include "../core/pwrseq.h"
+
+#define TRUE 1
+#define FALSE 0
+
+#define SD_FNC_AM_SDR50 0x2
+#define SD_FNC_AM_SDR104 0x3
+#define BIT_PASS_MASK (0x7ff)
+#define SDR104_MANUAL_INJECT 0x3ff
+#define SDR50_MANUAL_INJECT 0x77f
+
+#define TRUNING_RING_IDX(x) ((x) % TUNING_PHASE_SIZE)
+#define GET_IDX_VALUE(tb, x) (tb & (1 << (x)))
+#define GENERATE_IDX_VALUE(x) (1 << (x))
+#define GET_TRUNING_RING_IDX_VALUE(tb, x) \
+ (tb & (1 << TRUNING_RING_IDX(x)))
+#define GENERATE_TRUNING_RING_IDX_VALUE(x) \
+ (1 << TRUNING_RING_IDX(x))
+#define MAX_CFG_BIT_VAL (383)
+
+#define CORE_MCI_VERSION 0x50
+#define CORE_VERSION_MAJOR_SHIFT 28
+#define CORE_VERSION_MAJOR_MASK (0xf << CORE_VERSION_MAJOR_SHIFT)
+#define CORE_VERSION_MINOR_MASK 0xff
+
+#define CORE_MCI_GENERICS 0x70
+#define SWITCHABLE_SIGNALING_VOLTAGE BIT(29)
+
+#define HC_MODE_EN 0x1
+#define CORE_POWER 0x0
+#define CORE_SW_RST BIT(7)
+#define FF_CLK_SW_RST_DIS BIT(13)
+
+#define CORE_PWRCTL_BUS_OFF BIT(0)
+#define CORE_PWRCTL_BUS_ON BIT(1)
+#define CORE_PWRCTL_IO_LOW BIT(2)
+#define CORE_PWRCTL_IO_HIGH BIT(3)
+#define CORE_PWRCTL_BUS_SUCCESS BIT(0)
+#define CORE_PWRCTL_BUS_FAIL BIT(1)
+#define CORE_PWRCTL_IO_SUCCESS BIT(2)
+#define CORE_PWRCTL_IO_FAIL BIT(3)
+#define REQ_BUS_OFF BIT(0)
+#define REQ_BUS_ON BIT(1)
+#define REQ_IO_LOW BIT(2)
+#define REQ_IO_HIGH BIT(3)
+#define INT_MASK 0xf
+#define MAX_PHASES 16
+#define CORE_DLL_LOCK BIT(7)
+#define CORE_DDR_DLL_LOCK BIT(11)
+#define CORE_DLL_EN BIT(16)
+#define CORE_CDR_EN BIT(17)
+#define CORE_CK_OUT_EN BIT(18)
+#define CORE_CDR_EXT_EN BIT(19)
+#define CORE_DLL_PDN BIT(29)
+#define CORE_DLL_RST BIT(30)
+#define CORE_CMD_DAT_TRACK_SEL BIT(0)
+
+#define CORE_DDR_CAL_EN BIT(0)
+#define CORE_FLL_CYCLE_CNT BIT(18)
+#define CORE_DLL_CLOCK_DISABLE BIT(21)
+
+#define DLL_USR_CTL_POR_VAL 0x10800
+#define ENABLE_DLL_LOCK_STATUS BIT(26)
+#define FINE_TUNE_MODE_EN BIT(27)
+#define BIAS_OK_SIGNAL BIT(29)
+
+#define DLL_CONFIG_3_LOW_FREQ_VAL 0x08
+#define DLL_CONFIG_3_HIGH_FREQ_VAL 0x10
+
+#define CORE_VENDOR_SPEC_POR_VAL 0xa9c
+#define CORE_CLK_PWRSAVE BIT(1)
+#define CORE_HC_MCLK_SEL_DFLT (2 << 8)
+#define CORE_HC_MCLK_SEL_HS400 (3 << 8)
+#define CORE_HC_MCLK_SEL_MASK (3 << 8)
+#define CORE_IO_PAD_PWR_SWITCH_EN BIT(15)
+#define CORE_IO_PAD_PWR_SWITCH BIT(16)
+#define CORE_HC_SELECT_IN_EN BIT(18)
+#define CORE_HC_SELECT_IN_HS400 (6 << 19)
+#define CORE_HC_SELECT_IN_MASK (7 << 19)
+
+#define CORE_3_0V_SUPPORT BIT(25)
+#define CORE_1_8V_SUPPORT BIT(26)
+#define CORE_VOLT_SUPPORT (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT)
+
+#define CORE_CSR_CDC_CTLR_CFG0 0x130
+#define CORE_SW_TRIG_FULL_CALIB BIT(16)
+#define CORE_HW_AUTOCAL_ENA BIT(17)
+
+#define CORE_CSR_CDC_CTLR_CFG1 0x134
+#define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138
+#define CORE_TIMER_ENA BIT(16)
+
+#define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C
+#define CORE_CSR_CDC_REFCOUNT_CFG 0x140
+#define CORE_CSR_CDC_COARSE_CAL_CFG 0x144
+#define CORE_CDC_OFFSET_CFG 0x14C
+#define CORE_CSR_CDC_DELAY_CFG 0x150
+#define CORE_CDC_SLAVE_DDA_CFG 0x160
+#define CORE_CSR_CDC_STATUS0 0x164
+#define CORE_CALIBRATION_DONE BIT(0)
+
+#define CORE_CDC_ERROR_CODE_MASK 0x7000000
+
+#define CORE_CSR_CDC_GEN_CFG 0x178
+#define CORE_CDC_SWITCH_BYPASS_OFF BIT(0)
+#define CORE_CDC_SWITCH_RC_EN BIT(1)
+
+#define CORE_CDC_T4_DLY_SEL BIT(0)
+#define CORE_CMDIN_RCLK_EN BIT(1)
+#define CORE_START_CDC_TRAFFIC BIT(6)
+
+#define CORE_PWRSAVE_DLL BIT(3)
+
+#define DDR_CONFIG_POR_VAL 0x80040873
+
+
+#define INVALID_TUNING_PHASE -1
+#define SDHCI_MSM_MIN_CLOCK 400000
+#define CORE_FREQ_100MHZ (100 * 1000 * 1000)
+
+#define CDR_SELEXT_SHIFT 20
+#define CDR_SELEXT_MASK (0xf << CDR_SELEXT_SHIFT)
+#define CMUX_SHIFT_PHASE_SHIFT 24
+#define CMUX_SHIFT_PHASE_MASK (7 << CMUX_SHIFT_PHASE_SHIFT)
+
+#define MSM_MMC_AUTOSUSPEND_DELAY_MS 50
+
+/* Timeout value to avoid infinite waiting for pwr_irq */
+#define MSM_PWR_IRQ_TIMEOUT_MS 5000
+
+/* Max load for eMMC Vdd-io supply */
+#define MMC_VQMMC_MAX_LOAD_UA 325000
+
+#define msm_bayhub_host_readl(msm_bayhub_host, host, offset) \
+ msm_bayhub_host->var_ops->msm_bayhub_readl_relaxed(host, offset)
+
+#define msm_bayhub_host_writel(msm_bayhub_host, val, host, offset) \
+ msm_bayhub_host->var_ops->msm_bayhub_writel_relaxed(val, host, offset)
+
+/* CQHCI vendor specific registers */
+#define CQHCI_VENDOR_CFG1 0xA00
+#define CQHCI_VENDOR_DIS_RST_ON_CQ_EN (0x3 << 13)
+
+#define TUNING_PHASE_SIZE 11
+#define GGC_CFG_DATA {0x07000000, 0x07364022, 0x01015412, 0x01062400,\
+ 0x10400076, 0x00025432, 0x01046076, 0x62011000,\
+ 0x30503106, 0x64141711, 0x10057513, 0x00336200,\
+ 0x00020006, 0x40000400, 0x12200310, 0x3A314177}
+
+struct ggc_bus_mode_cfg_t {
+ u32 tx_selb_tb[TUNING_PHASE_SIZE];
+ u32 all_selb_tb[TUNING_PHASE_SIZE];
+ u32 tx_selb_failed_history;
+ int bus_mode;
+ int default_sela;
+ int default_selb;
+ u32 default_delaycode;
+ u32 dll_voltage_unlock_cnt[4];
+ u32 max_delaycode;
+ u32 min_delaycode;
+ u32 delaycode_narrowdown_index;
+ u32 fail_phase;
+};
+
+enum tuning_stat_et {
+ NO_TUNING = 0,
+ OUTPUT_PASS_TYPE = 1,
+ SET_PHASE_FAIL_TYPE = 2,
+ TUNING_FAIL_TYPE = 3,
+ READ_STATUS_FAIL_TYPE = 4,
+ TUNING_CMD7_TIMEOUT = 5,
+ RETUNING_CASE = 6,
+};
+
+
+struct t_gg_reg_strt {
+ u32 ofs;
+ u32 mask;
+ u32 value;
+};
+
+struct rl_bit_lct {
+ u8 bits;
+ u8 rl_bits;
+};
+
+struct chk_type_t {
+ u8 right_valid:1;
+ u8 first_valid:1;
+ u8 record_valid:1;
+ u8 reserved:5;
+};
+
+static const char *const op_dbg_str[] = {
+ "no tuning",
+ "pass",
+ "set_phase_fail",
+ "tuning fail",
+ "read status fail",
+ "tuning CMD7 timeout",
+ "retuning case"
+};
+
+struct ggc_platform_t {
+ struct ggc_bus_mode_cfg_t sdr50;
+ struct ggc_bus_mode_cfg_t sdr104;
+ struct ggc_bus_mode_cfg_t *cur_bus_mode;
+
+ struct t_gg_reg_strt pha_stas_rx_low32;
+ struct t_gg_reg_strt pha_stas_rx_high32;
+ struct t_gg_reg_strt pha_stas_tx_low32;
+ struct t_gg_reg_strt pha_stas_tx_high32;
+ struct t_gg_reg_strt dll_sela_after_mask;
+ struct t_gg_reg_strt dll_selb_after_mask;
+
+ struct t_gg_reg_strt dll_delay_100m_backup;
+ struct t_gg_reg_strt dll_delay_200m_backup;
+
+ struct t_gg_reg_strt dll_sela_100m_cfg;
+ struct t_gg_reg_strt dll_sela_200m_cfg;
+ struct t_gg_reg_strt dll_selb_100m_cfg;
+ struct t_gg_reg_strt dll_selb_200m_cfg;
+ struct t_gg_reg_strt dll_selb_100m_cfg_en;
+ struct t_gg_reg_strt dll_selb_200m_cfg_en;
+ struct t_gg_reg_strt internl_tuning_en_100m;
+ struct t_gg_reg_strt internl_tuning_en_200m;
+ struct t_gg_reg_strt cmd19_cnt_cfg;
+
+ struct t_gg_reg_strt inject_failure_for_tuning_enable_cfg;
+ struct t_gg_reg_strt inject_failure_for_200m_tuning_cfg;
+ struct t_gg_reg_strt inject_failure_for_100m_tuning_cfg;
+
+ int def_sela_100m;
+ int def_sela_200m;
+ int def_selb_100m;
+ int def_selb_200m;
+
+ u32 _gg_reg_cur[16];
+ u8 _cur_read_buf[512];
+
+ bool dll_unlock_reinit_flg;
+ u8 driver_strength_reinit_flg;
+ bool tuning_cmd7_timeout_reinit_flg;
+ u32 tuning_cmd7_timeout_reinit_cnt;
+ u32 ggc_cur_sela;
+ bool selx_tuning_done_flag;
+ u32 ggc_cmd_tx_selb_failed_range;
+ int ggc_sw_selb_tuning_first_selb;
+ enum tuning_stat_et ggc_sela_tuning_result[11];
+ int dll_voltage_scan_map[4];
+ int cur_dll_voltage_idx;
+ int sdr50_notuning_sela_inject_flag;
+ int sdr50_notuning_crc_error_flag;
+ u32 sdr50_notuning_sela_rx_inject;
+ u32 bh201_sdr50_sela_sw_inject;
+ u32 bh201_sdr50_selb_hw_inject;
+ u32 bh201_sdr104_selb_hw_inject;
+ u32 bh201_drive_strength;
+ bool tuning_in_progress;
+ int bh201_used;
+ int pwr_gpio; /* External power enable pin for Redriver IC */
+ int det_gpio;
+};
+
+struct sdhci_msm_bayhub_offset {
+ u32 core_hc_mode;
+ u32 core_mci_data_cnt;
+ u32 core_mci_status;
+ u32 core_mci_fifo_cnt;
+ u32 core_mci_version;
+ u32 core_generics;
+ u32 core_testbus_config;
+ u32 core_testbus_sel2_bit;
+ u32 core_testbus_ena;
+ u32 core_testbus_sel2;
+ u32 core_pwrctl_status;
+ u32 core_pwrctl_mask;
+ u32 core_pwrctl_clear;
+ u32 core_pwrctl_ctl;
+ u32 core_sdcc_debug_reg;
+ u32 core_dll_config;
+ u32 core_dll_status;
+ u32 core_vendor_spec;
+ u32 core_vendor_spec_adma_err_addr0;
+ u32 core_vendor_spec_adma_err_addr1;
+ u32 core_vendor_spec_func2;
+ u32 core_vendor_spec_capabilities0;
+ u32 core_ddr_200_cfg;
+ u32 core_vendor_spec3;
+ u32 core_dll_config_2;
+ u32 core_dll_config_3;
+ u32 core_ddr_config_old; /* Applicable to sdcc minor ver < 0x49 */
+ u32 core_ddr_config;
+ u32 core_dll_usr_ctl; /* Present on SDCC5.1 onwards */
+};
+
+static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_v5_offset = {
+ .core_mci_data_cnt = 0x35c,
+ .core_mci_status = 0x324,
+ .core_mci_fifo_cnt = 0x308,
+ .core_mci_version = 0x318,
+ .core_generics = 0x320,
+ .core_testbus_config = 0x32c,
+ .core_testbus_sel2_bit = 3,
+ .core_testbus_ena = (1 << 31),
+ .core_testbus_sel2 = (1 << 3),
+ .core_pwrctl_status = 0x240,
+ .core_pwrctl_mask = 0x244,
+ .core_pwrctl_clear = 0x248,
+ .core_pwrctl_ctl = 0x24c,
+ .core_sdcc_debug_reg = 0x358,
+ .core_dll_config = 0x200,
+ .core_dll_status = 0x208,
+ .core_vendor_spec = 0x20c,
+ .core_vendor_spec_adma_err_addr0 = 0x214,
+ .core_vendor_spec_adma_err_addr1 = 0x218,
+ .core_vendor_spec_func2 = 0x210,
+ .core_vendor_spec_capabilities0 = 0x21c,
+ .core_ddr_200_cfg = 0x224,
+ .core_vendor_spec3 = 0x250,
+ .core_dll_config_2 = 0x254,
+ .core_dll_config_3 = 0x258,
+ .core_ddr_config = 0x25c,
+ .core_dll_usr_ctl = 0x388,
+};
+
+static const struct sdhci_msm_bayhub_offset sdhci_msm_bayhub_mci_offset = {
+ .core_hc_mode = 0x78,
+ .core_mci_data_cnt = 0x30,
+ .core_mci_status = 0x34,
+ .core_mci_fifo_cnt = 0x44,
+ .core_mci_version = 0x050,
+ .core_generics = 0x70,
+ .core_testbus_config = 0x0cc,
+ .core_testbus_sel2_bit = 4,
+ .core_testbus_ena = (1 << 3),
+ .core_testbus_sel2 = (1 << 4),
+ .core_pwrctl_status = 0xdc,
+ .core_pwrctl_mask = 0xe0,
+ .core_pwrctl_clear = 0xe4,
+ .core_pwrctl_ctl = 0xe8,
+ .core_sdcc_debug_reg = 0x124,
+ .core_dll_config = 0x100,
+ .core_dll_status = 0x108,
+ .core_vendor_spec = 0x10c,
+ .core_vendor_spec_adma_err_addr0 = 0x114,
+ .core_vendor_spec_adma_err_addr1 = 0x118,
+ .core_vendor_spec_func2 = 0x110,
+ .core_vendor_spec_capabilities0 = 0x11c,
+ .core_ddr_200_cfg = 0x184,
+ .core_vendor_spec3 = 0x1b0,
+ .core_dll_config_2 = 0x1b4,
+ .core_ddr_config_old = 0x1b8,
+ .core_ddr_config = 0x1bc,
+};
+
+struct sdhci_msm_bayhub_variant_ops {
+ u32 (*msm_bayhub_readl_relaxed)(struct sdhci_host *host, u32 offset);
+ void (*msm_bayhub_writel_relaxed)(u32 val, struct sdhci_host *host,
+ u32 offset);
+};
+
+/*
+ * From V5, register spaces have changed. Wrap this info in a structure
+ * and choose the data_structure based on version info mentioned in DT.
+ */
+struct sdhci_msm_bayhub_variant_info {
+ bool mci_removed;
+ bool restore_dll_config;
+ bool uses_tassadar_dll;
+ const struct sdhci_msm_bayhub_variant_ops *var_ops;
+ const struct sdhci_msm_bayhub_offset *offset;
+};
+
+struct sdhci_msm_bayhub_host {
+ struct platform_device *pdev;
+ void __iomem *core_mem; /* MSM SDCC mapped address */
+ int pwr_irq; /* power irq */
+ struct clk *bus_clk; /* SDHC bus voter clock */
+ struct clk *xo_clk; /* TCXO clk needed for FLL feature of cm_dll*/
+ struct clk_bulk_data bulk_clks[4]; /* core, iface, cal, sleep clocks */
+ unsigned long clk_rate;
+ struct mmc_host *mmc;
+ struct opp_table *opp_table;
+ bool has_opp_table;
+ bool use_14lpp_dll_reset;
+ bool tuning_done;
+ bool calibration_done;
+ u8 saved_tuning_phase;
+ bool use_cdclp533;
+ u32 curr_pwr_state;
+ u32 curr_io_level;
+ wait_queue_head_t pwr_irq_wait;
+ bool pwr_irq_flag;
+ u32 caps_0;
+ bool mci_removed;
+ bool restore_dll_config;
+ const struct sdhci_msm_bayhub_variant_ops *var_ops;
+ const struct sdhci_msm_bayhub_offset *offset;
+ bool use_cdr;
+ u32 transfer_mode;
+ bool updated_ddr_cfg;
+ bool uses_tassadar_dll;
+ u32 dll_config;
+ u32 ddr_config;
+ bool vqmmc_enabled;
+ struct ggc_platform_t ggc;
+};
+
+static const struct sdhci_msm_bayhub_offset *sdhci_priv_msm_bayhub_offset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ return msm_bayhub_host->offset;
+}
+
+/*
+ * APIs to read/write to vendor specific registers which were there in the
+ * core_mem region before MCI was removed.
+ */
+static u32 sdhci_msm_bayhub_mci_variant_readl_relaxed(struct sdhci_host *host,
+ u32 offset)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ return readl_relaxed(msm_bayhub_host->core_mem + offset);
+}
+
+static u32 sdhci_msm_bayhub_v5_variant_readl_relaxed(struct sdhci_host *host,
+ u32 offset)
+{
+ return readl_relaxed(host->ioaddr + offset);
+}
+
+static void sdhci_msm_bayhub_mci_variant_writel_relaxed(u32 val,
+ struct sdhci_host *host, u32 offset)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ writel_relaxed(val, msm_bayhub_host->core_mem + offset);
+}
+
+static void sdhci_msm_bayhub_v5_variant_writel_relaxed(u32 val,
+ struct sdhci_host *host, u32 offset)
+{
+ writel_relaxed(val, host->ioaddr + offset);
+}
+
+static unsigned int msm_bayhub_get_clock_mult_for_bus_mode(struct sdhci_host *host)
+{
+ struct mmc_ios ios = host->mmc->ios;
+ /*
+ * The SDHC requires internal clock frequency to be double the
+ * actual clock that will be set for DDR mode. The controller
+ * uses the faster clock(100/400MHz) for some of its parts and
+ * send the actual required clock (50/200MHz) to the card.
+ */
+ if (ios.timing == MMC_TIMING_UHS_DDR50 ||
+ ios.timing == MMC_TIMING_MMC_DDR52 ||
+ ios.timing == MMC_TIMING_MMC_HS400 ||
+ host->flags & SDHCI_HS400_TUNING)
+ return 2;
+ return 1;
+}
+
+static void msm_bayhub_set_clock_rate_for_bus_mode(struct sdhci_host *host,
+ unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_ios curr_ios = host->mmc->ios;
+ struct clk *core_clk = msm_bayhub_host->bulk_clks[0].clk;
+ unsigned long achieved_rate;
+ unsigned int desired_rate;
+ unsigned int mult;
+ int rc;
+
+ mult = msm_bayhub_get_clock_mult_for_bus_mode(host);
+ desired_rate = clock * mult;
+ rc = dev_pm_opp_set_rate(mmc_dev(host->mmc), desired_rate);
+ if (rc) {
+ pr_err("%s: Failed to set clock at rate %u at timing %d\n",
+ mmc_hostname(host->mmc), desired_rate, curr_ios.timing);
+ return;
+ }
+
+ /*
+ * Qualcomm clock drivers by default round clock _up_ if they can't
+ * make the requested rate. This is not good for SD. Yell if we
+ * encounter it.
+ */
+ achieved_rate = clk_get_rate(core_clk);
+ if (achieved_rate > desired_rate)
+ pr_warn("%s: Card appears overclocked; req %u Hz, actual %lu Hz\n",
+ mmc_hostname(host->mmc), desired_rate, achieved_rate);
+ host->mmc->actual_clock = achieved_rate / mult;
+
+ /* Stash the rate we requested to use in sdhci_msm_bayhub_runtime_resume() */
+ msm_bayhub_host->clk_rate = desired_rate;
+
+ pr_debug("%s: Setting clock at rate %lu at timing %d\n",
+ mmc_hostname(host->mmc), achieved_rate, curr_ios.timing);
+}
+
+/* Platform specific tuning */
+static inline int msm_bayhub_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll)
+{
+ u32 wait_cnt = 50;
+ u8 ck_out_en;
+ struct mmc_host *mmc = host->mmc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ /* Poll for CK_OUT_EN bit. max. poll time = 50us */
+ ck_out_en = !!(readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config) & CORE_CK_OUT_EN);
+
+ while (ck_out_en != poll) {
+ if (--wait_cnt == 0) {
+ dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n",
+ mmc_hostname(mmc), poll);
+ return -ETIMEDOUT;
+ }
+ udelay(1);
+
+ ck_out_en = !!(readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config) & CORE_CK_OUT_EN);
+ }
+
+ return 0;
+}
+
+static int msm_bayhub_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
+{
+ int rc;
+ static const u8 grey_coded_phase_table[] = {
+ 0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4,
+ 0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8
+ };
+ unsigned long flags;
+ u32 config;
+ struct mmc_host *mmc = host->mmc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ if (phase > 0xf)
+ return -EINVAL;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN);
+ config |= (CORE_CDR_EXT_EN | CORE_DLL_EN);
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */
+ rc = msm_bayhub_dll_poll_ck_out_en(host, 0);
+ if (rc)
+ goto err_out;
+
+ /*
+ * Write the selected DLL clock output phase (0 ... 15)
+ * to CDR_SELEXT bit field of DLL_CONFIG register.
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~CDR_SELEXT_MASK;
+ config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
+ rc = msm_bayhub_dll_poll_ck_out_en(host, 1);
+ if (rc)
+ goto err_out;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CDR_EN;
+ config &= ~CORE_CDR_EXT_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+ goto out;
+
+err_out:
+ dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n",
+ mmc_hostname(mmc), phase);
+out:
+ spin_unlock_irqrestore(&host->lock, flags);
+ return rc;
+}
+
+/*
+ * Find out the greatest range of consecuitive selected
+ * DLL clock output phases that can be used as sampling
+ * setting for SD3.0 UHS-I card read operation (in SDR104
+ * timing mode) or for eMMC4.5 card read operation (in
+ * HS400/HS200 timing mode).
+ * Select the 3/4 of the range and configure the DLL with the
+ * selected DLL clock output phase.
+ */
+
+static int msm_bayhub_find_most_appropriate_phase(struct sdhci_host *host,
+ u8 *phase_table, u8 total_phases)
+{
+ int ret;
+ u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} };
+ u8 phases_per_row[MAX_PHASES] = { 0 };
+ int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0;
+ int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0;
+ bool phase_0_found = false, phase_15_found = false;
+ struct mmc_host *mmc = host->mmc;
+
+ if (!total_phases || (total_phases > MAX_PHASES)) {
+ dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n",
+ mmc_hostname(mmc), total_phases);
+ return -EINVAL;
+ }
+
+ for (cnt = 0; cnt < total_phases; cnt++) {
+ ranges[row_index][col_index] = phase_table[cnt];
+ phases_per_row[row_index] += 1;
+ col_index++;
+
+ if ((cnt + 1) == total_phases) {
+ continue;
+ /* check if next phase in phase_table is consecutive or not */
+ } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) {
+ row_index++;
+ col_index = 0;
+ }
+ }
+
+ if (row_index >= MAX_PHASES)
+ return -EINVAL;
+
+ /* Check if phase-0 is present in first valid window? */
+ if (!ranges[0][0]) {
+ phase_0_found = true;
+ phase_0_raw_index = 0;
+ /* Check if cycle exist between 2 valid windows */
+ for (cnt = 1; cnt <= row_index; cnt++) {
+ if (phases_per_row[cnt]) {
+ for (i = 0; i < phases_per_row[cnt]; i++) {
+ if (ranges[cnt][i] == 15) {
+ phase_15_found = true;
+ phase_15_raw_index = cnt;
+ break;
+ }
+ }
+ }
+ }
+ }
+
+ /* If 2 valid windows form cycle then merge them as single window */
+ if (phase_0_found && phase_15_found) {
+ /* number of phases in raw where phase 0 is present */
+ u8 phases_0 = phases_per_row[phase_0_raw_index];
+ /* number of phases in raw where phase 15 is present */
+ u8 phases_15 = phases_per_row[phase_15_raw_index];
+
+ if (phases_0 + phases_15 >= MAX_PHASES)
+ /*
+ * If there are more than 1 phase windows then total
+ * number of phases in both the windows should not be
+ * more than or equal to MAX_PHASES.
+ */
+ return -EINVAL;
+
+ /* Merge 2 cyclic windows */
+ i = phases_15;
+ for (cnt = 0; cnt < phases_0; cnt++) {
+ ranges[phase_15_raw_index][i] =
+ ranges[phase_0_raw_index][cnt];
+ if (++i >= MAX_PHASES)
+ break;
+ }
+
+ phases_per_row[phase_0_raw_index] = 0;
+ phases_per_row[phase_15_raw_index] = phases_15 + phases_0;
+ }
+
+ for (cnt = 0; cnt <= row_index; cnt++) {
+ if (phases_per_row[cnt] > curr_max) {
+ curr_max = phases_per_row[cnt];
+ selected_row_index = cnt;
+ }
+ }
+
+ i = (curr_max * 3) / 4;
+ if (i)
+ i--;
+
+ ret = ranges[selected_row_index][i];
+
+ if (ret >= MAX_PHASES) {
+ ret = -EINVAL;
+ dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n",
+ mmc_hostname(mmc), ret);
+ }
+
+ return ret;
+}
+
+static inline void msm_bayhub_cm_dll_set_freq(struct sdhci_host *host)
+{
+ u32 mclk_freq = 0, config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ /* Program the MCLK value to MCLK_FREQ bit field */
+ if (host->clock <= 112000000)
+ mclk_freq = 0;
+ else if (host->clock <= 125000000)
+ mclk_freq = 1;
+ else if (host->clock <= 137000000)
+ mclk_freq = 2;
+ else if (host->clock <= 150000000)
+ mclk_freq = 3;
+ else if (host->clock <= 162000000)
+ mclk_freq = 4;
+ else if (host->clock <= 175000000)
+ mclk_freq = 5;
+ else if (host->clock <= 187000000)
+ mclk_freq = 6;
+ else if (host->clock <= 200000000)
+ mclk_freq = 7;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config &= ~CMUX_SHIFT_PHASE_MASK;
+ config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+}
+
+/* Initialize the DLL (Programmable Delay Line) */
+static int msm_bayhub_init_cm_dll(struct sdhci_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int wait_cnt = 50;
+ unsigned long flags, xo_clk = 0;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ if (msm_bayhub_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_bayhub_host->xo_clk))
+ xo_clk = clk_get_rate(msm_bayhub_host->xo_clk);
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ /*
+ * Make sure that clock is always enabled when DLL
+ * tuning is in progress. Keeping PWRSAVE ON may
+ * turn off the clock.
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_CLK_PWRSAVE;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ if (msm_bayhub_host->dll_config)
+ writel_relaxed(msm_bayhub_host->dll_config,
+ host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config |= CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ if (!msm_bayhub_host->dll_config)
+ msm_bayhub_cm_dll_set_freq(host);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset &&
+ !IS_ERR_OR_NULL(msm_bayhub_host->xo_clk)) {
+ u32 mclk_freq = 0;
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= CORE_FLL_CYCLE_CNT;
+ if (config)
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8),
+ xo_clk);
+ else
+ mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4),
+ xo_clk);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= ~(0xFF << 10);
+ config |= mclk_freq << 10;
+
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ /* wait for 5us before enabling DLL clock */
+ udelay(5);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config &= ~CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ if (msm_bayhub_host->use_14lpp_dll_reset) {
+ if (!msm_bayhub_host->dll_config)
+ msm_bayhub_cm_dll_set_freq(host);
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ config &= ~CORE_DLL_CLOCK_DISABLE;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_2);
+ }
+
+ /*
+ * Configure DLL user control register to enable DLL status.
+ * This setting is applicable to SDCC v5.1 onwards only.
+ */
+ if (msm_bayhub_host->uses_tassadar_dll) {
+ config = DLL_USR_CTL_POR_VAL | FINE_TUNE_MODE_EN |
+ ENABLE_DLL_LOCK_STATUS | BIAS_OK_SIGNAL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_usr_ctl);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config_3);
+ config &= ~0xFF;
+ if (msm_bayhub_host->clk_rate < 150000000)
+ config |= DLL_CONFIG_3_LOW_FREQ_VAL;
+ else
+ config |= DLL_CONFIG_3_HIGH_FREQ_VAL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config_3);
+ }
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_CK_OUT_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
+ while (!(readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_status) &
+ CORE_DLL_LOCK)) {
+ /* max. wait for 50us sec for LOCK bit to be set */
+ if (--wait_cnt == 0) {
+ dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
+ mmc_hostname(mmc));
+ spin_unlock_irqrestore(&host->lock, flags);
+ return -ETIMEDOUT;
+ }
+ udelay(1);
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
+ return 0;
+}
+
+static void msm_bayhub_hc_select_default(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ if (!msm_bayhub_host->use_cdclp533) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ config &= ~CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_DFLT;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ /*
+ * Disable HC_SELECT_IN to be able to use the UHS mode select
+ * configuration from Host Control2 register for all other
+ * modes.
+ * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field
+ * in VENDOR_SPEC_FUNC
+ */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_SELECT_IN_EN;
+ config &= ~CORE_HC_SELECT_IN_MASK;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ /*
+ * Make sure above writes impacting free running MCLK are completed
+ * before changing the clk_rate at GCC.
+ */
+ wmb();
+}
+
+static void msm_bayhub_hc_select_hs400(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_ios ios = host->mmc->ios;
+ u32 config, dll_lock;
+ int rc;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ /* Select the divided clock (free running MCLK/2) */
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ config &= ~CORE_HC_MCLK_SEL_MASK;
+ config |= CORE_HC_MCLK_SEL_HS400;
+
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ /*
+ * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC
+ * register
+ */
+ if ((msm_bayhub_host->tuning_done || ios.enhanced_strobe) &&
+ !msm_bayhub_host->calibration_done) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ config |= CORE_HC_SELECT_IN_HS400;
+ config |= CORE_HC_SELECT_IN_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ }
+ if (!msm_bayhub_host->clk_rate && !msm_bayhub_host->use_cdclp533) {
+ /*
+ * Poll on DLL_LOCK or DDR_DLL_LOCK bits in
+ * core_dll_status to be set. This should get set
+ * within 15 us at 200 MHz.
+ */
+ rc = readl_relaxed_poll_timeout(host->ioaddr +
+ msm_bayhub_offset->core_dll_status,
+ dll_lock,
+ (dll_lock &
+ (CORE_DLL_LOCK |
+ CORE_DDR_DLL_LOCK)), 10,
+ 1000);
+ if (rc == -ETIMEDOUT)
+ pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n",
+ mmc_hostname(host->mmc), dll_lock);
+ }
+ /*
+ * Make sure above writes impacting free running MCLK are completed
+ * before changing the clk_rate at GCC.
+ */
+ wmb();
+}
+
+/*
+ * sdhci_msm_bayhub_hc_select_mode :- In general all timing modes are
+ * controlled via UHS mode select in Host Control2 register.
+ * eMMC specific HS200/HS400 doesn't have their respective modes
+ * defined here, hence we use these values.
+ *
+ * HS200 - SDR104 (Since they both are equivalent in functionality)
+ * HS400 - This involves multiple configurations
+ * Initially SDR104 - when tuning is required as HS200
+ * Then when switching to DDR @ 400MHz (HS400) we use
+ * the vendor specific HC_SELECT_IN to control the mode.
+ *
+ * In addition to controlling the modes we also need to select the
+ * correct input clock for DLL depending on the mode.
+ *
+ * HS400 - divided clock (free running MCLK/2)
+ * All other modes - default (free running MCLK)
+ */
+static void sdhci_msm_bayhub_hc_select_mode(struct sdhci_host *host)
+{
+ struct mmc_ios ios = host->mmc->ios;
+
+ if (ios.timing == MMC_TIMING_MMC_HS400 ||
+ host->flags & SDHCI_HS400_TUNING)
+ msm_bayhub_hc_select_hs400(host);
+ else
+ msm_bayhub_hc_select_default(host);
+}
+
+static int sdhci_msm_bayhub_cdclp533_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 config, calib_done;
+ int ret;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ /* Set the selected phase in delay line hw block */
+ ret = msm_bayhub_config_cm_dll_phase(host, msm_bayhub_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config &= ~CORE_CDC_T4_DLY_SEL;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config &= ~CORE_CDC_SWITCH_BYPASS_OFF;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+ config |= CORE_CDC_SWITCH_RC_EN;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config &= ~CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+
+ /* Perform CDC Register Initialization Sequence */
+
+ writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1);
+ writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1);
+ writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG);
+ writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG);
+ writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG);
+ writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG);
+ writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG);
+
+ /* CDC HW Calibration */
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config &= ~CORE_SW_TRIG_FULL_CALIB;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+ config |= CORE_HW_AUTOCAL_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
+
+ config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+ config |= CORE_TIMER_ENA;
+ writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0,
+ calib_done,
+ (calib_done & CORE_CALIBRATION_DONE),
+ 1, 50);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CDC calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0)
+ & CORE_CDC_ERROR_CODE_MASK;
+ if (ret) {
+ pr_err("%s: %s: CDC error code %d\n",
+ mmc_hostname(host->mmc), __func__, ret);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+ config |= CORE_START_CDC_TRAFFIC;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_ddr_200_cfg);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_cm_dll_sdc4_calibration(struct sdhci_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ u32 dll_status, config, ddr_cfg_offset;
+ int ret;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Currently the core_ddr_config register defaults to desired
+ * configuration on reset. Currently reprogramming the power on
+ * reset (POR) value in case it might have been modified by
+ * bootloaders. In the future, if this changes, then the desired
+ * values will need to be programmed appropriately.
+ */
+ if (msm_bayhub_host->updated_ddr_cfg)
+ ddr_cfg_offset = msm_bayhub_offset->core_ddr_config;
+ else
+ ddr_cfg_offset = msm_bayhub_offset->core_ddr_config_old;
+ writel_relaxed(msm_bayhub_host->ddr_config, host->ioaddr + ddr_cfg_offset);
+
+ if (mmc->ios.enhanced_strobe) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_ddr_200_cfg);
+ config |= CORE_CMDIN_RCLK_EN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_ddr_200_cfg);
+ }
+
+ config = readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_2);
+ config |= CORE_DDR_CAL_EN;
+ writel_relaxed(config, host->ioaddr + msm_bayhub_offset->core_dll_config_2);
+
+ ret = readl_relaxed_poll_timeout(host->ioaddr +
+ msm_bayhub_offset->core_dll_status,
+ dll_status,
+ (dll_status & CORE_DDR_DLL_LOCK),
+ 10, 1000);
+
+ if (ret == -ETIMEDOUT) {
+ pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n",
+ mmc_hostname(host->mmc), __func__);
+ goto out;
+ }
+
+ /*
+ * Set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3.
+ * When MCLK is gated OFF, it is not gated for less than 0.5us
+ * and MCLK must be switched on for at-least 1us before DATA
+ * starts coming. Controllers with 14lpp and later tech DLL cannot
+ * guarantee above requirement. So PWRSAVE_DLL should not be
+ * turned on for host controllers using this DLL.
+ */
+ if (!msm_bayhub_host->use_14lpp_dll_reset) {
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ config |= CORE_PWRSAVE_DLL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec3);
+ }
+
+ /*
+ * Drain writebuffer to ensure above DLL calibration
+ * and PWRSAVE DLL is enabled.
+ */
+ wmb();
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_hs400_dll_calibration(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_host *mmc = host->mmc;
+ int ret;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
+
+ /*
+ * Retuning in HS400 (DDR mode) will fail, just reset the
+ * tuning block and restore the saved tuning phase.
+ */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ goto out;
+
+ if (!mmc->ios.enhanced_strobe) {
+ /* Set the selected phase in delay line hw block */
+ ret = msm_bayhub_config_cm_dll_phase(host,
+ msm_bayhub_host->saved_tuning_phase);
+ if (ret)
+ goto out;
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_CMD_DAT_TRACK_SEL;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ }
+
+ if (msm_bayhub_host->use_cdclp533)
+ ret = sdhci_msm_bayhub_cdclp533_calibration(host);
+ else
+ ret = sdhci_msm_bayhub_cm_dll_sdc4_calibration(host);
+out:
+ pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
+ __func__, ret);
+ return ret;
+}
+
+static bool sdhci_msm_bayhub_is_tuning_needed(struct sdhci_host *host)
+{
+ struct mmc_ios *ios = &host->mmc->ios;
+
+ /*
+ * Tuning is required for SDR104, HS200 and HS400 cards and
+ * if clock frequency is greater than 100MHz in these modes.
+ */
+ if (host->clock <= CORE_FREQ_100MHZ ||
+ !(ios->timing == MMC_TIMING_MMC_HS400 ||
+ ios->timing == MMC_TIMING_MMC_HS200 ||
+ ios->timing == MMC_TIMING_UHS_SDR104) ||
+ ios->enhanced_strobe)
+ return false;
+
+ return true;
+}
+
+static int sdhci_msm_bayhub_restore_sdr_dll_config(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ /*
+ * SDR DLL comes into picture only for timing modes which needs
+ * tuning.
+ */
+ if (!sdhci_msm_bayhub_is_tuning_needed(host))
+ return 0;
+
+ /* Reset the tuning block */
+ ret = msm_bayhub_init_cm_dll(host);
+ if (ret)
+ return ret;
+
+ /* Restore the tuning block */
+ ret = msm_bayhub_config_cm_dll_phase(host, msm_bayhub_host->saved_tuning_phase);
+
+ return ret;
+}
+
+static void sdhci_msm_bayhub_set_cdr(struct sdhci_host *host, bool enable)
+{
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ sdhci_priv_msm_bayhub_offset(host);
+ u32 config, oldconfig = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = oldconfig;
+ if (enable) {
+ config |= CORE_CDR_EN;
+ config &= ~CORE_CDR_EXT_EN;
+ } else {
+ config &= ~CORE_CDR_EN;
+ config |= CORE_CDR_EXT_EN;
+ }
+
+ if (config != oldconfig) {
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ }
+}
+
+static int sdhci_msm_bayhub_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ int tuning_seq_cnt = 10;
+ u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
+ int rc;
+ struct mmc_ios ios = host->mmc->ios;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!sdhci_msm_bayhub_is_tuning_needed(host)) {
+ msm_bayhub_host->use_cdr = false;
+ sdhci_msm_bayhub_set_cdr(host, false);
+ return 0;
+ }
+
+ /* Clock-Data-Recovery used to dynamically adjust RX sampling point */
+ msm_bayhub_host->use_cdr = true;
+
+ /*
+ * Clear tuning_done flag before tuning to ensure proper
+ * HS400 settings.
+ */
+ msm_bayhub_host->tuning_done = 0;
+
+ /*
+ * For HS400 tuning in HS200 timing requires:
+ * - select MCLK/2 in VENDOR_SPEC
+ * - program MCLK to 400MHz (or nearest supported) in GCC
+ */
+ if (host->flags & SDHCI_HS400_TUNING) {
+ sdhci_msm_bayhub_hc_select_mode(host);
+ msm_bayhub_set_clock_rate_for_bus_mode(host, ios.clock);
+ host->flags &= ~SDHCI_HS400_TUNING;
+ }
+
+retry:
+ /* First of all reset the tuning block */
+ rc = msm_bayhub_init_cm_dll(host);
+ if (rc)
+ return rc;
+
+ phase = 0;
+ do {
+ /* Set the phase in delay line hw block */
+ rc = msm_bayhub_config_cm_dll_phase(host, phase);
+ if (rc)
+ return rc;
+
+ rc = mmc_send_tuning(mmc, opcode, NULL);
+ if (!rc) {
+ /* Tuning is successful at this tuning point */
+ tuned_phases[tuned_phase_cnt++] = phase;
+ dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
+ mmc_hostname(mmc), phase);
+ }
+
+ if (msm_bayhub_host->ggc.bh201_used)
+ usleep_range(1000, 1200);
+
+ } while (++phase < ARRAY_SIZE(tuned_phases));
+
+ if (tuned_phase_cnt) {
+ if (tuned_phase_cnt == ARRAY_SIZE(tuned_phases)) {
+ /*
+ * All phases valid is _almost_ as bad as no phases
+ * valid. Probably all phases are not really reliable
+ * but we didn't detect where the unreliable place is.
+ * That means we'll essentially be guessing and hoping
+ * we get a good phase. Better to try a few times.
+ */
+ dev_dbg(mmc_dev(mmc), "%s: All phases valid; try again\n",
+ mmc_hostname(mmc));
+ if (--tuning_seq_cnt) {
+ tuned_phase_cnt = 0;
+ goto retry;
+ }
+ }
+
+ rc = msm_bayhub_find_most_appropriate_phase(host, tuned_phases,
+ tuned_phase_cnt);
+ if (rc >= 0)
+ phase = rc;
+ else
+ return rc;
+
+ /*
+ * Finally set the selected phase in delay
+ * line hw block.
+ */
+ rc = msm_bayhub_config_cm_dll_phase(host, phase);
+ if (rc)
+ return rc;
+ msm_bayhub_host->saved_tuning_phase = phase;
+ dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
+ mmc_hostname(mmc), phase);
+ } else {
+ if (--tuning_seq_cnt)
+ goto retry;
+ /* Tuning failed */
+ dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n",
+ mmc_hostname(mmc));
+ rc = -EIO;
+ }
+
+ if (!rc)
+ msm_bayhub_host->tuning_done = true;
+ return rc;
+}
+
+static const unsigned int freqs[] = { 400000, 300000, 200000, 100000 };
+
+static void cfg_bit_2_bt(int max_bit, int tar, int *byt, int *bit)
+{
+ struct rl_bit_lct cfg_bit_map[6] = {
+ {0, 6}, {1, 5}, {2, 4},
+ {3, 2}, {4, 1}, {5, 0},
+ };
+
+ *byt = (max_bit - tar) / 6;
+ *bit = cfg_bit_map[(max_bit - tar) % 6].rl_bits;
+}
+
+static u32 cfg_read_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+ return rv;
+}
+
+static void get_default_setting(struct sdhci_host *host, u8 *data)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ vendor_host->ggc.def_sela_100m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
+ vendor_host->ggc.def_sela_200m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
+ vendor_host->ggc.def_selb_100m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_100m_cfg);
+ vendor_host->ggc.def_selb_200m =
+ cfg_read_bits_ofs_mask(data, &vendor_host->ggc.dll_sela_200m_cfg);
+}
+
+static void cfg_write_bits_ofs_mask(u8 *cfg,
+ struct t_gg_reg_strt *bts, u32 w_value)
+{
+ u32 wv = w_value & bts->mask;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ cfg_bit_2_bt(MAX_CFG_BIT_VAL, bts->ofs + i, &byt, &bit);
+ if (wv & 1)
+ cfg[byt] |= (u8) (1 << bit);
+ else
+ cfg[byt] &= (u8) (~(1 << bit));
+
+ i++;
+ wv >>= 1;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+}
+
+static void ram_bit_2_bt(int tar, int *byt, int *bit)
+{
+ *byt = tar / 8;
+ *bit = tar % 8;
+}
+
+static void set_gg_reg_cur_val(struct ggc_platform_t *ggc,
+ u8 *data, u8 len)
+{
+ memcpy(&ggc->_gg_reg_cur[0], data, len);
+}
+
+static void get_gg_reg_cur_val(struct ggc_platform_t *ggc,
+ u8 *data, u8 len)
+{
+ memcpy(data, &ggc->_gg_reg_cur[0], len);
+}
+
+static void get_gg_reg_def(struct sdhci_host *host, u8 *data)
+{
+ u32 gg_sw_def[16] = GGC_CFG_DATA;
+
+ memcpy(data, (u8 *)&(gg_sw_def[0]), sizeof(gg_sw_def));
+}
+
+static u32 read_ram_bits_ofs_mask(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ ram_bit_2_bt(bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+
+ } while (1);
+ return rv;
+}
+
+static void ggc_dll_voltage_init(struct sdhci_host *host)
+{
+ int i = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ for (i = 0; i < 4; i++) {
+ vendor_host->ggc.dll_voltage_scan_map[i] = 0;
+ vendor_host->ggc.sdr50.dll_voltage_unlock_cnt[i] = 0;
+ vendor_host->ggc.sdr104.dll_voltage_unlock_cnt[i] = 0;
+ }
+}
+
+static void ggc_chip_init(struct sdhci_host *host)
+{
+ u8 data[512] = { 0 };
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_def(host, data);
+ get_default_setting(host, data);
+ set_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+}
+
+static int driver_send_command7(struct sdhci_host *host)
+{
+ int ret = 0;
+ int err;
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_command cmd = {0};
+
+ cmd.opcode = MMC_SELECT_CARD;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+ err = mmc_wait_for_cmd(mmc, &cmd, 3);
+ if (err)
+ ret = 0;
+ else
+ ret = 1;
+
+ return ret;
+}
+
+static void driver_send_command24(struct sdhci_host *host,
+ u32 *cfg_data, int data_len)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_request mrq = {0};
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+
+ memcpy(data1, (u8 *)&(cfg_data[0]), data_len);
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_WRITE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_WRITE;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+ kfree(data1);
+}
+
+static void bht_update_cfg(struct mmc_host *mmc_host,
+ struct mmc_card *card, u32 *cfg_data, int data_len)
+{
+ int ret = 0;
+ struct sdhci_host *host;
+
+ host = mmc_priv(mmc_host);
+ mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_4);
+ if (host->ops->reset)
+ host->ops->reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
+
+ driver_send_command7(host);
+ driver_send_command24(host, cfg_data, data_len);
+ driver_send_command7(host);
+
+ mmc_set_bus_width(mmc_host, MMC_BUS_WIDTH_1);
+}
+
+
+static void tx_selb_failed_tb_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ memset(&vendor_host->ggc.sdr104.tx_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr104.tx_selb_tb));
+ memset(&vendor_host->ggc.sdr50.tx_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr50.tx_selb_tb));
+}
+
+static void all_selb_failed_tb_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ memset(vendor_host->ggc.sdr104.all_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr104.all_selb_tb));
+ memset(vendor_host->ggc.sdr50.all_selb_tb, 0xff,
+ sizeof(vendor_host->ggc.sdr50.all_selb_tb));
+}
+
+static void tx_selb_failed_history_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ vendor_host->ggc.sdr50.tx_selb_failed_history = BIT_PASS_MASK;
+ vendor_host->ggc.sdr104.tx_selb_failed_history = BIT_PASS_MASK;
+}
+
+static void ggc_reset_selx_failed_tb(struct sdhci_host *host)
+{
+ tx_selb_failed_tb_reset(host);
+ all_selb_failed_tb_reset(host);
+ tx_selb_failed_history_reset(host);
+}
+
+static void _ggc_reset_sela_tuning_result(
+ struct sdhci_msm_bayhub_host *host)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ host->ggc.ggc_sela_tuning_result[i] = NO_TUNING;
+}
+
+static void _ggc_reset_tuning_result_for_dll(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ ggc_reset_selx_failed_tb(host);
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range = BIT_PASS_MASK;
+ vendor_host->ggc.selx_tuning_done_flag = 0;
+ _ggc_reset_sela_tuning_result(vendor_host);
+}
+
+static void ggc_tuning_result_reset(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+
+ _ggc_reset_tuning_result_for_dll(host);
+
+ vendor_host->ggc.sdr50.bus_mode = SD_FNC_AM_SDR50;
+ vendor_host->ggc.sdr104.bus_mode = SD_FNC_AM_SDR104;
+ vendor_host->ggc.driver_strength_reinit_flg = 0;
+ vendor_host->ggc.cur_bus_mode = NULL;
+ vendor_host->ggc.dll_unlock_reinit_flg = 0;
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 0;
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_cnt = 0;
+ vendor_host->ggc.sdr50_notuning_sela_inject_flag = 1;
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 0;
+ if (vendor_host->ggc.bh201_sdr50_sela_sw_inject)
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject =
+ vendor_host->ggc.bh201_sdr50_sela_sw_inject;
+ else
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject = 0x47F;
+}
+
+static void bht_load_hw_inject(struct mmc_host *mmc_host,
+ struct mmc_card *card, u32 *cfg_data, int data_len,
+ u32 sel200, u32 sel100)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+ u32 gg_hw_inj[16] = GGC_CFG_DATA;
+
+ gg_hw_inj[1] = 0x7364032;
+
+ if (vendor_host->ggc.bh201_sdr104_selb_hw_inject)
+ gg_hw_inj[11] = vendor_host->ggc.bh201_sdr104_selb_hw_inject;
+ else
+ gg_hw_inj[11] = 0x57336200;
+
+ if (vendor_host->ggc.bh201_sdr50_selb_hw_inject)
+ gg_hw_inj[12] = vendor_host->ggc.bh201_sdr50_selb_hw_inject;
+ else
+ gg_hw_inj[12] = 0x00725777;
+
+ if (vendor_host->ggc.bh201_drive_strength)
+ gg_hw_inj[15] = vendor_host->ggc.bh201_drive_strength;
+
+ bht_update_cfg(mmc_host, card, gg_hw_inj, data_len);
+}
+
+static void bht_load(struct mmc_host *mmc_host, struct mmc_card *card)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host =
+ sdhci_pltfm_priv(pltfm_host);
+ u8 driver_strength_reinit_flg =
+ vendor_host->ggc.driver_strength_reinit_flg;
+ int cur_dll_voltage_idx = vendor_host->ggc.cur_dll_voltage_idx;
+ u32 i = 0;
+ u32 reg;
+ u32 gg_sw_def[16] = GGC_CFG_DATA;
+ u8 data[512];
+ static const int s_dll_voltage_cfg[4][2] = {
+ {0x30503106, 0x64141711},
+ {0x31503106, 0x64141711},
+ {0x30503106, 0x64141751},
+ {0x31503106, 0x64141751},
+ };
+
+ if (vendor_host->ggc.bh201_used) {
+ pr_debug("%s: Load BHT patch\n", mmc_hostname(mmc_host));
+
+ mmc_send_relative_addr(mmc_host, &card->rca);
+ mmc_host->card = card;
+ if (vendor_host->ggc.dll_unlock_reinit_flg) {
+ pr_debug("dll unlock reinit: idx=%d\n",
+ cur_dll_voltage_idx);
+ ggc_tuning_result_reset(host);
+ gg_sw_def[8] = s_dll_voltage_cfg[cur_dll_voltage_idx][0];
+ gg_sw_def[9] = s_dll_voltage_cfg[cur_dll_voltage_idx][1];
+ }
+ if (vendor_host->ggc.driver_strength_reinit_flg) {
+ pr_debug("%s: driver strength should be init to %d\n",
+ mmc_hostname(mmc_host), driver_strength_reinit_flg);
+ ggc_tuning_result_reset(host);
+ if (vendor_host->ggc.driver_strength_reinit_flg <= 7) {
+ gg_sw_def[15] &= 0x0f0fffff;
+ gg_sw_def[15] |= (driver_strength_reinit_flg << 28)
+ | (driver_strength_reinit_flg << 20);
+ }
+ }
+ driver_send_command7(host);
+ if (vendor_host->ggc.tuning_cmd7_timeout_reinit_flg == 0
+ && vendor_host->ggc.selx_tuning_done_flag == 0) {
+ bht_load_hw_inject(mmc_host, card, gg_sw_def,
+ sizeof(gg_sw_def), 0x3ff, 0x77f);
+ bht_update_cfg(mmc_host, card, gg_sw_def, sizeof(gg_sw_def));
+ set_gg_reg_cur_val(&vendor_host->ggc, (u8 *)gg_sw_def, sizeof(gg_sw_def));
+ } else {
+ if (vendor_host->ggc.selx_tuning_done_flag)
+ pr_debug("%s: skip load default configuration for tuning done\n",
+ mmc_hostname(mmc_host));
+ if (vendor_host->ggc.tuning_cmd7_timeout_reinit_flg) {
+ pr_debug("%s: write previous inject results to bh201 for cmd7 timeout flag is set\n",
+ mmc_hostname(mmc_host));
+ get_gg_reg_cur_val(&vendor_host->ggc, data, sizeof(gg_sw_def));
+
+ pr_debug("%s: dump config data before write to bh201\n", __func__);
+ for (i = 0; i < 128; i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("ggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+ bht_update_cfg(mmc_host, card, (u32 *)data, sizeof(data));
+ }
+ }
+ }
+}
+
+static void bh201_signal_voltage_on_off(struct sdhci_host *host, u32 on_off)
+{
+ int card_present_status = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (vendor_host->ggc.bh201_used) {
+ if (gpio_is_valid(vendor_host->ggc.det_gpio)) {
+ card_present_status = gpio_get_value(vendor_host->ggc.det_gpio);
+ pr_debug("%s: detect_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.det_gpio, card_present_status);
+ } else {
+ pr_err("%s: no det_gpio provided\n", mmc_hostname(host->mmc));
+ }
+
+ if (on_off) {
+ pr_debug("%s: apply bht power on patch\n", mmc_hostname(host->mmc));
+
+ ggc_dll_voltage_init(host);
+
+ ggc_chip_init(host);
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ gpio_direction_output(vendor_host->ggc.pwr_gpio, 1);
+ msleep(100);
+ pr_debug("%s: pwr_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio,
+ gpio_get_value(vendor_host->ggc.pwr_gpio));
+ } else {
+ pr_err("%s: no pwr_gpio provided\n", mmc_hostname(host->mmc));
+ }
+ } else {
+ pr_debug("%s: apply bht power off patch\n", mmc_hostname(host->mmc));
+
+ ggc_dll_voltage_init(host);
+
+ if (card_present_status <= 0) {
+ pr_debug("%s: clear tuning result for power off and card removed\n",
+ mmc_hostname(host->mmc));
+ ggc_tuning_result_reset(host);
+ }
+ ggc_chip_init(host);
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ gpio_direction_output(vendor_host->ggc.pwr_gpio, 0);
+ pr_debug("%s: pwr_gpio pin %d status is %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio,
+ gpio_get_value(vendor_host->ggc.pwr_gpio));
+ } else {
+ pr_err("%s: no pwr_gpio provided\n", mmc_hostname(host->mmc));
+ }
+ }
+ }
+}
+
+static void sdhci_bh201_parse(struct mmc_host *mmc_host)
+{
+ struct sdhci_host *host = mmc_priv(mmc_host);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct device_node *np = vendor_host->pdev->dev.of_node;
+ struct t_gg_reg_strt index_array[] = {
+ { 14, 0xffffffff, 0 }, { 46, 0xffffffff, 0 },
+ { 205, 0xffffffff, 0 }, { 237, 0xffffffff, 0 },
+ { 141, 0xf, 0 }, { 145, 0xf, 0 },
+ { 83, 0xfff, 0 }, { 95, 0xfff, 0 },
+ { 126, 0xf, 0 }, { 130, 0xf, 0 },
+ { 140, 0xf, 0 }, { 144, 0xf, 0 },
+ { 183, 0x1, 0 }, { 184, 0x1, 0 },
+ { 171, 0x1, 0 }, { 172, 0x1, 0 },
+ { 173, 0x3f, 0 }, { 357, 0x1, 0 },
+ { 93, 0x7ff, 0 }, { 81, 0x7ff, 0 },
+ };
+
+ memcpy(&vendor_host->ggc.pha_stas_rx_low32, &index_array[0],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_rx_high32, &index_array[1],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_tx_low32, &index_array[2],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.pha_stas_tx_high32, &index_array[3],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_sela_after_mask, &index_array[4],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_after_mask, &index_array[5],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.dll_delay_100m_backup, &index_array[6],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_delay_200m_backup, &index_array[7],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.dll_sela_100m_cfg, &index_array[8],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_sela_200m_cfg, &index_array[9],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_100m_cfg, &index_array[10],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_200m_cfg, &index_array[11],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_100m_cfg_en, &index_array[12],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.dll_selb_200m_cfg_en, &index_array[13],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.internl_tuning_en_100m, &index_array[14],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.internl_tuning_en_200m, &index_array[15],
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.cmd19_cnt_cfg, &index_array[16],
+ sizeof(struct t_gg_reg_strt));
+
+ memcpy(&vendor_host->ggc.inject_failure_for_tuning_enable_cfg,
+ &index_array[17], sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.inject_failure_for_200m_tuning_cfg,
+ &index_array[18], sizeof(struct t_gg_reg_strt));
+ memcpy(&vendor_host->ggc.inject_failure_for_100m_tuning_cfg,
+ &index_array[19], sizeof(struct t_gg_reg_strt));
+
+ vendor_host->ggc.bh201_drive_strength = 0;
+ vendor_host->ggc.bh201_sdr50_sela_sw_inject = 0;
+ vendor_host->ggc.bh201_sdr50_selb_hw_inject = 0;
+ vendor_host->ggc.bh201_sdr104_selb_hw_inject = 0;
+ vendor_host->ggc.bh201_used = 1;
+ host->flags |= SDHCI_SDR50_NEEDS_TUNING;
+ host->mmc_host_ops.init_card = bht_load;
+
+ if (of_find_property(np, "bh201_drive_strength", NULL))
+ of_property_read_u32_index(np, "bh201_drive_strength", 0,
+ &vendor_host->ggc.bh201_drive_strength);
+ if (of_find_property(np, "bh201_sdr50_sela_sw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr50_sela_sw_inject", 0,
+ &vendor_host->ggc.bh201_sdr50_sela_sw_inject);
+ if (of_find_property(np, "bh201_sdr50_selb_hw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr50_selb_hw_inject", 0,
+ &vendor_host->ggc.bh201_sdr50_selb_hw_inject);
+ if (of_find_property(np, "bh201_sdr104_selb_hw_inject", NULL))
+ of_property_read_u32_index(np, "bh201_sdr104_selb_hw_inject", 0,
+ &vendor_host->ggc.bh201_sdr104_selb_hw_inject);
+
+ vendor_host->ggc.pwr_gpio = of_get_named_gpio(np, "pwr-gpios", 0);
+ if (!gpio_is_valid(vendor_host->ggc.pwr_gpio))
+ dev_err(&vendor_host->pdev->dev, "no pwr-gpio provided !\n");
+ else
+ dev_info(&vendor_host->pdev->dev, "pwr-gpio provided\n");
+
+ vendor_host->ggc.det_gpio = of_get_named_gpio(np, "det-gpios", 0);
+ if (!gpio_is_valid(vendor_host->ggc.det_gpio))
+ dev_err(&vendor_host->pdev->dev, "no det-gpio provided !\n");
+ else
+ dev_info(&vendor_host->pdev->dev, "det-gpio provided\n");
+
+ if (gpio_is_valid(vendor_host->ggc.pwr_gpio)) {
+ devm_gpio_request_one(&vendor_host->pdev->dev, vendor_host->ggc.pwr_gpio,
+ GPIOF_OUT_INIT_LOW, "sprd-1-pwr");
+ pr_debug("%s: detect_gpio pin %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.pwr_gpio);
+ } else {
+ pr_err("%s: no detect_gpio provided\n",
+ mmc_hostname(host->mmc));
+ }
+
+ if (gpio_is_valid(vendor_host->ggc.det_gpio)) {
+ devm_gpio_request_one(&vendor_host->pdev->dev, vendor_host->ggc.det_gpio,
+ GPIOF_DIR_IN, "sprd-1-det");
+ pr_debug("%s: detect_gpio pin %d\n",
+ mmc_hostname(host->mmc), vendor_host->ggc.det_gpio);
+ } else {
+ pr_err("%s: no detect_gpio provided\n",
+ mmc_hostname(host->mmc));
+ }
+}
+
+static int sd_select_driver_type(struct mmc_card *card, u8 *status)
+{
+ int card_drv_type, drive_strength, drv_type;
+ int err;
+
+ card->drive_strength = 0;
+
+ card_drv_type = card->sw_caps.sd3_drv_type | SD_DRIVER_TYPE_B;
+
+ drive_strength = mmc_select_drive_strength(card,
+ card->sw_caps.uhs_max_dtr,
+ card_drv_type, &drv_type);
+
+ if (drive_strength) {
+ err = mmc_sd_switch(card, 1, 2, drive_strength, status);
+ if (err)
+ return err;
+ if ((status[15] & 0xF) != drive_strength) {
+ pr_warn("%s: Problem setting drive strength!\n",
+ mmc_hostname(card->host));
+ return 0;
+ }
+ card->drive_strength = drive_strength;
+ }
+
+ if (drv_type)
+ mmc_set_driver_type(card->host, drv_type);
+
+ return 0;
+}
+
+/* Get host's max current setting at its current voltage */
+static u32 sd_get_host_max_current(struct mmc_host *host)
+{
+ u32 voltage, max_current;
+
+ voltage = 1 << host->ios.vdd;
+ switch (voltage) {
+ case MMC_VDD_165_195:
+ max_current = host->max_current_180;
+ break;
+ case MMC_VDD_29_30:
+ case MMC_VDD_30_31:
+ max_current = host->max_current_300;
+ break;
+ case MMC_VDD_32_33:
+ case MMC_VDD_33_34:
+ max_current = host->max_current_330;
+ break;
+ default:
+ max_current = 0;
+ }
+
+ return max_current;
+}
+
+static int sd_set_current_limit(struct mmc_card *card, u8 *status)
+{
+ int current_limit = SD_SET_CURRENT_NO_CHANGE;
+ int err;
+ u32 max_current;
+
+ /*
+ * Current limit switch is only defined for SDR50, SDR104, and DDR50
+ * bus speed modes. For other bus speed modes, we do not change the
+ * current limit.
+ */
+ if ((card->sd_bus_speed != UHS_SDR50_BUS_SPEED) &&
+ (card->sd_bus_speed != UHS_SDR104_BUS_SPEED) &&
+ (card->sd_bus_speed != UHS_DDR50_BUS_SPEED))
+ return 0;
+
+ /*
+ * Host has different current capabilities when operating at
+ * different voltages, so find out its max current first.
+ */
+ max_current = sd_get_host_max_current(card->host);
+
+ /*
+ * We only check host's capability here, if we set a limit that is
+ * higher than the card's maximum current, the card will be using its
+ * maximum current, e.g. if the card's maximum current is 300ma, and
+ * when we set current limit to 200ma, the card will draw 200ma, and
+ * when we set current limit to 400/600/800ma, the card will draw its
+ * maximum 300ma from the host.
+ *
+ * The above is incorrect: if we try to set a current limit that is
+ * not supported by the card, the card can rightfully error out the
+ * attempt, and remain at the default current limit. This results
+ * in a 300mA card being limited to 200mA even though the host
+ * supports 800mA. Failures seen with SanDisk 8GB UHS cards with
+ * an iMX6 host. --rmk
+ */
+ if (max_current >= 800 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_800)
+ current_limit = SD_SET_CURRENT_LIMIT_800;
+ else if (max_current >= 600 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_600)
+ current_limit = SD_SET_CURRENT_LIMIT_600;
+ else if (max_current >= 400 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_400)
+ current_limit = SD_SET_CURRENT_LIMIT_400;
+ else if (max_current >= 200 &&
+ card->sw_caps.sd3_curr_limit & SD_MAX_CURRENT_200)
+ current_limit = SD_SET_CURRENT_LIMIT_200;
+
+ if (current_limit != SD_SET_CURRENT_NO_CHANGE) {
+ err = mmc_sd_switch(card, 1, 3, current_limit, status);
+ if (err)
+ return err;
+
+ if (((status[15] >> 4) & 0x0F) != current_limit)
+ pr_warn("%s: Problem setting current limit!\n",
+ mmc_hostname(card->host));
+
+ }
+
+ return 0;
+}
+
+static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
+{
+ int err;
+ unsigned int timing = 0;
+
+ switch (card->sd_bus_speed) {
+ case UHS_SDR104_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR104;
+ card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
+ break;
+ case UHS_DDR50_BUS_SPEED:
+ timing = MMC_TIMING_UHS_DDR50;
+ card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
+ break;
+ case UHS_SDR50_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR50;
+ card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
+ break;
+ case UHS_SDR25_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR25;
+ card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
+ break;
+ case UHS_SDR12_BUS_SPEED:
+ timing = MMC_TIMING_UHS_SDR12;
+ card->sw_caps.uhs_max_dtr = UHS_SDR12_MAX_DTR;
+ break;
+ default:
+ return 0;
+ }
+
+ err = mmc_sd_switch(card, 1, 0, card->sd_bus_speed, status);
+ if (err)
+ return err;
+
+ if ((status[16] & 0xF) != card->sd_bus_speed)
+ pr_warn("%s: Problem setting bus speed mode!\n",
+ mmc_hostname(card->host));
+ else {
+ mmc_set_timing(card->host, timing);
+ mmc_set_clock(card->host, card->sw_caps.uhs_max_dtr);
+ }
+
+ return 0;
+}
+
+static void sd_update_bus_speed_mode(struct mmc_card *card)
+{
+ /*
+ * If the host doesn't support any of the UHS-I modes, fallback on
+ * default speed.
+ */
+ if (!mmc_host_uhs(card->host)) {
+ card->sd_bus_speed = 0;
+ return;
+ }
+
+ if ((card->host->caps & MMC_CAP_UHS_SDR104) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)) {
+ card->sd_bus_speed = UHS_SDR104_BUS_SPEED;
+ } else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
+ card->sd_bus_speed = UHS_DDR50_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
+ SD_MODE_UHS_SDR50)) {
+ card->sd_bus_speed = UHS_SDR50_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
+ (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
+ card->sd_bus_speed = UHS_SDR25_BUS_SPEED;
+ } else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+ MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
+ MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
+ SD_MODE_UHS_SDR12)) {
+ card->sd_bus_speed = UHS_SDR12_BUS_SPEED;
+ }
+}
+
+static int mmc_wait_for_app_cmd(struct mmc_host *host, struct mmc_card *card,
+ struct mmc_command *cmd)
+{
+ struct mmc_request mrq = {};
+ int i, err = -EIO;
+
+ /*
+ * We have to resend MMC_APP_CMD for each attempt so
+ * we cannot use the retries field in mmc_command.
+ */
+ for (i = 0; i <= MMC_CMD_RETRIES; i++) {
+ err = mmc_app_cmd(host, card);
+ if (err) {
+ /* no point in retrying; no APP commands allowed */
+ if (mmc_host_is_spi(host)) {
+ if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
+ break;
+ }
+ continue;
+ }
+
+ memset(&mrq, 0, sizeof(struct mmc_request));
+
+ memset(cmd->resp, 0, sizeof(cmd->resp));
+ cmd->retries = 0;
+
+ mrq.cmd = cmd;
+ cmd->data = NULL;
+
+ mmc_wait_for_req(host, &mrq);
+
+ err = cmd->error;
+ if (!cmd->error)
+ break;
+
+ /* no point in retrying illegal APP commands */
+ if (mmc_host_is_spi(host)) {
+ if (cmd->resp[0] & R1_SPI_ILLEGAL_COMMAND)
+ break;
+ }
+ }
+
+ return err;
+}
+
+static int mmc_app_set_clr_card_detect(struct mmc_card *card)
+{
+ struct mmc_command cmd = {};
+
+ cmd.opcode = 42;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+
+ return mmc_wait_for_app_cmd(card->host, card, &cmd);
+}
+
+/*
+ * UHS-I specific initialization procedure
+ */
+static int sd_init_uhs_card(struct mmc_card *card)
+{
+ int err;
+ u8 *status;
+
+ if (!(card->csd.cmdclass & CCC_SWITCH))
+ return 0;
+
+ status = kmalloc(64, GFP_KERNEL);
+ if (!status)
+ return -ENOMEM;
+
+ /* Set 4-bit bus width */
+ err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
+ if (err)
+ goto out;
+
+ mmc_set_bus_width(card->host, MMC_BUS_WIDTH_4);
+
+ /*
+ * Select the bus speed mode depending on host
+ * and card capability.
+ */
+ sd_update_bus_speed_mode(card);
+
+ mmc_app_set_clr_card_detect(card);
+
+ /* Set the driver strength for the card */
+ err = sd_select_driver_type(card, status);
+ if (err)
+ goto out;
+
+ /* Set current limit for the card */
+ err = sd_set_current_limit(card, status);
+ if (err)
+ goto out;
+
+ /* Set bus speed mode of the card */
+ err = sd_set_bus_speed_mode(card, status);
+ if (err)
+ goto out;
+
+ /*
+ * SPI mode doesn't define CMD19 and tuning is only valid for SDR50 and
+ * SDR104 mode SD-cards. Note that tuning is mandatory for SDR104.
+ */
+ if (!mmc_host_is_spi(card->host) &&
+ (card->host->ios.timing == MMC_TIMING_UHS_SDR50 ||
+ card->host->ios.timing == MMC_TIMING_UHS_DDR50 ||
+ card->host->ios.timing == MMC_TIMING_UHS_SDR104)) {
+ err = mmc_execute_tuning(card);
+
+ /*
+ * As SD Specifications Part1 Physical Layer Specification
+ * Version 3.01 says, CMD19 tuning is available for unlocked
+ * cards in transfer state of 1.8V signaling mode. The small
+ * difference between v3.00 and 3.01 spec means that CMD19
+ * tuning is also available for DDR50 mode.
+ */
+ if (err && card->host->ios.timing == MMC_TIMING_UHS_DDR50) {
+ pr_warn("%s: ddr50 tuning failed\n",
+ mmc_hostname(card->host));
+ err = 0;
+ }
+ }
+
+out:
+ kfree(status);
+
+ return err;
+}
+
+static bool mmc_sd_card_using_v18(struct mmc_card *card)
+{
+ /*
+ * According to the SD spec., the Bus Speed Mode (function group 1) bits
+ * 2 to 4 are zero if the card is initialized at 3.3V signal level. Thus
+ * they can be used to determine if the card has already switched to
+ * 1.8V signaling.
+ */
+ return card->sw_caps.sd3_bus_mode &
+ (SD_MODE_UHS_SDR50 | SD_MODE_UHS_SDR104 | SD_MODE_UHS_DDR50);
+}
+
+/*
+ * Fetches and decodes switch information
+ */
+static int mmc_read_switch(struct mmc_card *card)
+{
+ int err;
+ u8 *status;
+
+ if (card->scr.sda_vsn < SCR_SPEC_VER_1)
+ return 0;
+
+ if (!(card->csd.cmdclass & CCC_SWITCH)) {
+ pr_warn("%s: card lacks mandatory switch function, performance might suffer\n",
+ mmc_hostname(card->host));
+ return 0;
+ }
+
+ status = kmalloc(64, GFP_KERNEL);
+ if (!status)
+ return -ENOMEM;
+
+ /*
+ * Find out the card's support bits with a mode 0 operation.
+ * The argument does not matter, as the support bits do not
+ * change with the arguments.
+ */
+ err = mmc_sd_switch(card, 0, 0, 0, status);
+ if (err) {
+ /*
+ * If the host or the card can't do the switch,
+ * fail more gracefully.
+ */
+ if (err != -EINVAL && err != -ENOSYS && err != -EFAULT)
+ goto out;
+
+ pr_warn("%s: problem reading Bus Speed modes\n",
+ mmc_hostname(card->host));
+ err = 0;
+
+ goto out;
+ }
+
+ if (status[13] & SD_MODE_HIGH_SPEED)
+ card->sw_caps.hs_max_dtr = HIGH_SPEED_MAX_DTR;
+
+ if (card->scr.sda_spec3) {
+ card->sw_caps.sd3_bus_mode = status[13];
+ /* Driver Strengths supported by the card */
+ card->sw_caps.sd3_drv_type = status[9];
+ card->sw_caps.sd3_curr_limit = status[7] | status[6] << 8;
+ }
+
+out:
+ kfree(status);
+
+ return err;
+}
+
+/*
+ * Handle the detection and initialisation of a card.
+ *
+ * In the case of a resume, "oldcard" will contain the card
+ * we're trying to reinitialise.
+ */
+int sd_init_card(struct mmc_host *host, u32 ocr,
+ struct mmc_card *oldcard)
+{
+ struct mmc_card *card;
+ int err;
+ u32 cid[4];
+ u32 rocr = 0;
+ bool v18_fixup_failed = false;
+
+ WARN_ON(!host->claimed);
+retry:
+ err = mmc_sd_get_cid(host, ocr, cid, &rocr);
+ if (err)
+ return err;
+
+ if (oldcard) {
+ if (memcmp(cid, oldcard->raw_cid, sizeof(cid)) != 0) {
+ pr_debug("%s: Perhaps the card was replaced\n",
+ mmc_hostname(host));
+ return -ENOENT;
+ }
+
+ card = oldcard;
+ } else {
+ /*
+ * Allocate card structure.
+ */
+ card = mmc_alloc_card(host, &sd_type);
+ if (IS_ERR(card))
+ return PTR_ERR(card);
+
+ card->ocr = ocr;
+ card->type = MMC_TYPE_SD;
+ memcpy(card->raw_cid, cid, sizeof(card->raw_cid));
+ }
+
+ /*
+ * Call the optional HC's init_card function to handle quirks.
+ */
+ if (host->ops->init_card)
+ host->ops->init_card(host, card);
+
+ /*
+ * For native busses: get card RCA and quit open drain mode.
+ */
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_send_relative_addr(host, &card->rca);
+ if (err)
+ goto free_card;
+ }
+
+ if (!oldcard) {
+ err = mmc_sd_get_csd(host, card);
+ if (err)
+ goto free_card;
+
+ mmc_decode_cid(card);
+ }
+
+ /*
+ * handling only for cards supporting DSR and hosts requesting
+ * DSR configuration
+ */
+ if (card->csd.dsr_imp && host->dsr_req)
+ mmc_set_dsr(host);
+
+ /*
+ * Select card, as all following commands rely on that.
+ */
+ if (!mmc_host_is_spi(host)) {
+ err = mmc_select_card(card);
+ if (err)
+ goto free_card;
+ }
+
+ err = mmc_sd_setup_card(host, card, oldcard != NULL);
+ if (err)
+ goto free_card;
+
+ /*
+ * If the card has not been power cycled, it may still be using 1.8V
+ * signaling. Detect that situation and try to initialize a UHS-I (1.8V)
+ * transfer mode.
+ */
+ if (!v18_fixup_failed && !mmc_host_is_spi(host) && mmc_host_uhs(host) &&
+ mmc_sd_card_using_v18(card) &&
+ host->ios.signal_voltage != MMC_SIGNAL_VOLTAGE_180) {
+ /*
+ * Re-read switch information in case it has changed since
+ * oldcard was initialized.
+ */
+ if (oldcard) {
+ err = mmc_read_switch(card);
+ if (err)
+ goto free_card;
+ }
+ if (mmc_sd_card_using_v18(card)) {
+ if (mmc_host_set_uhs_voltage(host) ||
+ sd_init_uhs_card(card)) {
+ v18_fixup_failed = true;
+ mmc_power_cycle(host, ocr);
+ if (!oldcard)
+ mmc_remove_card(card);
+ goto retry;
+ }
+ goto done;
+ }
+ }
+
+ /* Initialization sequence for UHS-I cards */
+ if (rocr & SD_ROCR_S18A && mmc_host_uhs(host)) {
+ err = sd_init_uhs_card(card);
+ if (err)
+ goto free_card;
+ } else {
+ /*
+ * Switch to wider bus (if supported).
+ */
+ if ((host->caps & MMC_CAP_4_BIT_DATA) &&
+ (card->scr.bus_widths & SD_SCR_BUS_WIDTH_4)) {
+ err = mmc_app_set_bus_width(card, MMC_BUS_WIDTH_4);
+ if (err)
+ goto free_card;
+
+ mmc_set_bus_width(host, MMC_BUS_WIDTH_4);
+ }
+
+ mmc_app_set_clr_card_detect(card);
+
+ /*
+ * Attempt to change to high-speed (if supported)
+ */
+ err = mmc_sd_switch_hs(card);
+ if (err > 0)
+ mmc_set_timing(card->host, MMC_TIMING_SD_HS);
+ else if (err)
+ goto free_card;
+
+ /*
+ * Set bus speed.
+ */
+ mmc_set_clock(host, mmc_sd_get_max_clock(card));
+ }
+
+ if (host->caps2 & MMC_CAP2_AVOID_3_3V &&
+ host->ios.signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ pr_err("%s: Host failed to negotiate down from 3.3V\n",
+ mmc_hostname(host));
+ err = -EINVAL;
+ goto free_card;
+ }
+done:
+
+ host->card = card;
+ return 0;
+
+free_card:
+ if (!oldcard)
+ mmc_remove_card(card);
+
+ return err;
+}
+
+
+/*
+ * Host is being removed. Free up the current card.
+ */
+static void mmc_sd_remove(struct mmc_host *host)
+{
+ mmc_remove_card(host->card);
+ host->card = NULL;
+}
+
+/*
+ * Card detection - card is alive.
+ */
+static int mmc_sd_alive(struct mmc_host *host)
+{
+ return mmc_send_status(host->card, NULL);
+}
+
+/*
+ * Card detection callback from host.
+ */
+static void mmc_sd_detect(struct mmc_host *host)
+{
+ int err;
+
+ mmc_get_card(host->card, NULL);
+
+ /*
+ * Just check if our card has been removed.
+ */
+ err = _mmc_detect_card_removed(host);
+
+ mmc_put_card(host->card, NULL);
+
+ if (err) {
+ mmc_sd_remove(host);
+
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+ mmc_power_off(host);
+ mmc_release_host(host);
+ }
+}
+
+static int _mmc_sd_suspend(struct mmc_host *host)
+{
+ int err = 0;
+
+ mmc_claim_host(host);
+
+ if (mmc_card_suspended(host->card))
+ goto out;
+
+ if (!mmc_host_is_spi(host))
+ err = mmc_deselect_cards(host);
+
+ if (!err) {
+ mmc_power_off(host);
+ mmc_card_set_suspended(host->card);
+ }
+
+out:
+ mmc_release_host(host);
+ return err;
+}
+
+/*
+ * Callback for suspend
+ */
+static int mmc_sd_suspend(struct mmc_host *host)
+{
+ int err;
+
+ err = _mmc_sd_suspend(host);
+ if (!err) {
+ pm_runtime_disable(&host->card->dev);
+ pm_runtime_set_suspended(&host->card->dev);
+ }
+
+ return err;
+}
+
+/*
+ * This function tries to determine if the same card is still present
+ * and, if so, restore all state to it.
+ */
+static int _mmc_sd_resume(struct mmc_host *host)
+{
+ int err = 0;
+
+ mmc_claim_host(host);
+
+ if (!mmc_card_suspended(host->card))
+ goto out;
+
+ mmc_power_up(host, host->card->ocr);
+ err = sd_init_card(host, host->card->ocr, host->card);
+ mmc_card_clr_suspended(host->card);
+
+out:
+ mmc_release_host(host);
+ return err;
+}
+
+/*
+ * Callback for resume
+ */
+static int mmc_sd_resume(struct mmc_host *host)
+{
+ pm_runtime_enable(&host->card->dev);
+ return 0;
+}
+
+/*
+ * Callback for runtime_suspend.
+ */
+static int mmc_sd_runtime_suspend(struct mmc_host *host)
+{
+ int err;
+
+ if (!(host->caps & MMC_CAP_AGGRESSIVE_PM))
+ return 0;
+
+ err = _mmc_sd_suspend(host);
+ if (err)
+ pr_err("%s: error %d doing aggressive suspend\n",
+ mmc_hostname(host), err);
+
+ return err;
+}
+
+/*
+ * Callback for runtime_resume.
+ */
+static int mmc_sd_runtime_resume(struct mmc_host *host)
+{
+ int err;
+
+ err = _mmc_sd_resume(host);
+ if (err && err != -ENOMEDIUM)
+ pr_err("%s: error %d doing runtime resume\n",
+ mmc_hostname(host), err);
+
+ return 0;
+}
+
+static int mmc_sd_hw_reset(struct mmc_host *host)
+{
+ mmc_power_cycle(host, host->card->ocr);
+ return sd_init_card(host, host->card->ocr, host->card);
+}
+
+static const struct mmc_bus_ops mmc_sd_ops = {
+ .remove = mmc_sd_remove,
+ .detect = mmc_sd_detect,
+ .runtime_suspend = mmc_sd_runtime_suspend,
+ .runtime_resume = mmc_sd_runtime_resume,
+ .suspend = mmc_sd_suspend,
+ .resume = mmc_sd_resume,
+ .alive = mmc_sd_alive,
+ .shutdown = mmc_sd_suspend,
+ .hw_reset = mmc_sd_hw_reset,
+};
+
+/*
+ * Starting point for SD card init.
+ */
+static int attach_sd(struct mmc_host *host)
+{
+ int err;
+ u32 ocr, rocr;
+
+ WARN_ON(!host->claimed);
+
+ err = mmc_send_app_op_cond(host, 0, &ocr);
+ if (err)
+ return err;
+
+ mmc_attach_bus(host, &mmc_sd_ops);
+ if (host->ocr_avail_sd)
+ host->ocr_avail = host->ocr_avail_sd;
+
+ /*
+ * We need to get OCR a different way for SPI.
+ */
+ if (mmc_host_is_spi(host)) {
+ mmc_go_idle(host);
+
+ err = mmc_spi_read_ocr(host, 0, &ocr);
+ if (err)
+ goto err;
+ }
+
+ /*
+ * Some SD cards claims an out of spec VDD voltage range. Let's treat
+ * these bits as being in-valid and especially also bit7.
+ */
+ ocr &= ~0x7FFF;
+
+ rocr = mmc_select_voltage(host, ocr);
+
+ /*
+ * Can we support the voltage(s) of the card(s)?
+ */
+ if (!rocr) {
+ err = -EINVAL;
+ goto err;
+ }
+
+ /*
+ * Detect and init the card.
+ */
+ err = sd_init_card(host, rocr, NULL);
+ if (err)
+ goto err;
+
+ mmc_release_host(host);
+ err = mmc_add_card(host->card);
+ if (err)
+ goto remove_card;
+
+ mmc_claim_host(host);
+ return 0;
+
+remove_card:
+ mmc_remove_card(host->card);
+ host->card = NULL;
+ mmc_claim_host(host);
+err:
+ mmc_detach_bus(host);
+
+ pr_err("%s: error %d whilst initialising SD card\n",
+ mmc_hostname(host), err);
+
+ return err;
+}
+
+static int mmc_schedule_delayed_work(struct delayed_work *work,
+ unsigned long delay)
+{
+ /*
+ * We use the system_freezable_wq, because of two reasons.
+ * First, it allows several works (not the same work item) to be
+ * executed simultaneously. Second, the queue becomes frozen when
+ * userspace becomes frozen during system PM.
+ */
+ return queue_delayed_work(system_freezable_wq, work, delay);
+}
+
+static void mmc_hw_reset_for_init(struct mmc_host *host)
+{
+ mmc_pwrseq_reset(host);
+
+ if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset)
+ return;
+ host->ops->hw_reset(host);
+}
+
+static int mmc_rescan_try_freq(struct mmc_host *host, unsigned int freq)
+{
+ host->f_init = freq;
+
+ pr_debug("%s: %s: trying to init card at %u Hz\n",
+ mmc_hostname(host), __func__, host->f_init);
+
+ mmc_power_up(host, host->ocr_avail);
+
+ /*
+ * Some eMMCs (with VCCQ always on) may not be reset after power up, so
+ * do a hardware reset if possible.
+ */
+ mmc_hw_reset_for_init(host);
+
+ /*
+ * sdio_reset sends CMD52 to reset card. Since we do not know
+ * if the card is being re-initialized, just send it. CMD52
+ * should be ignored by SD/eMMC cards.
+ * Skip it if we already know that we do not support SDIO commands
+ */
+ if (!(host->caps2 & MMC_CAP2_NO_SDIO))
+ sdio_reset(host);
+
+ mmc_go_idle(host);
+
+ if (!(host->caps2 & MMC_CAP2_NO_SD))
+ mmc_send_if_cond(host, host->ocr_avail);
+
+ /* Order's important: probe SDIO, then SD, then MMC */
+ if (!(host->caps2 & MMC_CAP2_NO_SDIO))
+ if (!mmc_attach_sdio(host))
+ return 0;
+
+ if (!(host->caps2 & MMC_CAP2_NO_SD))
+ if (!attach_sd(host))
+ return 0;
+
+ if (!(host->caps2 & MMC_CAP2_NO_MMC))
+ if (!mmc_attach_mmc(host))
+ return 0;
+
+ mmc_power_off(host);
+ return -EIO;
+}
+
+/*
+ * Cleanup when the last reference to the bus operator is dropped.
+ */
+static void __mmc_release_bus(struct mmc_host *host)
+{
+ WARN_ON(!host->bus_dead);
+
+ host->bus_ops = NULL;
+}
+
+/*
+ * Increase reference count of bus operator
+ */
+static inline void mmc_bus_get(struct mmc_host *host)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->bus_refs++;
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+/*
+ * Decrease reference count of bus operator and free it if
+ * it is the last reference.
+ */
+static inline void mmc_bus_put(struct mmc_host *host)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ host->bus_refs--;
+ if ((host->bus_refs == 0) && host->bus_ops)
+ __mmc_release_bus(host);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+void mmc_rescan_bayhub(struct work_struct *work)
+{
+ struct mmc_host *host =
+ container_of(work, struct mmc_host, detect.work);
+ int i;
+
+ if (host->rescan_disable)
+ return;
+
+ /* If there is a non-removable card registered, only scan once */
+ if (!mmc_card_is_removable(host) && host->rescan_entered)
+ return;
+ host->rescan_entered = 1;
+
+ if (host->trigger_card_event && host->ops->card_event) {
+ mmc_claim_host(host);
+ host->ops->card_event(host);
+ mmc_release_host(host);
+ host->trigger_card_event = false;
+ }
+
+ mmc_bus_get(host);
+
+ /* Verify a registered card to be functional, else remove it. */
+ if (host->bus_ops && !host->bus_dead)
+ host->bus_ops->detect(host);
+
+ host->detect_change = 0;
+
+ /*
+ * Let mmc_bus_put() free the bus/bus_ops if we've found that
+ * the card is no longer present.
+ */
+ mmc_bus_put(host);
+ mmc_bus_get(host);
+
+ /* if there still is a card present, stop here */
+ if (host->bus_ops != NULL) {
+ mmc_bus_put(host);
+ goto out;
+ }
+
+ /*
+ * Only we can add a new handler, so it's safe to
+ * release the lock here.
+ */
+ mmc_bus_put(host);
+
+ mmc_claim_host(host);
+ if (mmc_card_is_removable(host) && host->ops->get_cd &&
+ host->ops->get_cd(host) == 0) {
+ mmc_power_off(host);
+ mmc_release_host(host);
+ goto out;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(freqs); i++) {
+ if (!mmc_rescan_try_freq(host, max(freqs[i], host->f_min)))
+ break;
+ if (freqs[i] <= host->f_min)
+ break;
+ }
+ mmc_release_host(host);
+
+ out:
+ if (host->caps & MMC_CAP_NEEDS_POLL)
+ mmc_schedule_delayed_work(&host->detect, HZ);
+}
+
+static int card_deselect_card(struct sdhci_host *host)
+{
+ int ret = -1;
+ int err;
+ struct mmc_host *mmc = host->mmc;
+ struct mmc_command cmd = { 0 };
+
+ cmd.opcode = MMC_SELECT_CARD;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+
+ err = mmc_wait_for_cmd(mmc, &cmd, 3);
+ if (err)
+ pr_err("BHT ERR: CMD7 FAIL: err = %d\n", err);
+ else
+ ret = 0;
+
+ return ret;
+}
+
+static bool enter_exit_emulator_mode(struct sdhci_host *host, bool b_enter)
+{
+ bool ret = FALSE;
+ u8 times = b_enter ? 2 : 1;
+ u8 i = 0;
+
+ for (i = 0; i < times; i++) {
+ ret = card_deselect_card(host);
+ if (ret)
+ break;
+ }
+ return ret;
+}
+
+static bool _gg_emulator_read_only(struct sdhci_host *host,
+ u8 *in_data, u32 datalen)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int rc = 0;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+ struct mmc_request mrq = { 0 };
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+
+ if (!data1) {
+ pr_err("BHT MSG:gg read no memory\n");
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_READ_SINGLE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_READ;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+ memcpy(in_data, data1, datalen);
+
+ kfree(data1);
+
+ if ((cmd.error == -EILSEQ) || (data.error == -EILSEQ))
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+
+ if (cmd.error || data.error)
+ rc = -1;
+out:
+ return rc;
+}
+
+static void host_cmddat_line_reset(struct sdhci_host *host)
+{
+ if (host->ops->reset)
+ host->ops->reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
+}
+
+static int gg_select_card_spec(struct sdhci_host *host)
+{
+ int err;
+ struct mmc_command cmd = { 0 };
+ struct mmc_card *card = host->mmc->card;
+
+ cmd.opcode = MMC_SELECT_CARD;
+
+ if (card) {
+ cmd.arg = card->rca << 16;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
+ } else {
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_NONE | MMC_CMD_AC;
+ }
+
+ err = mmc_wait_for_cmd(host->mmc, &cmd, 0);
+ if (err == -EILSEQ) {
+ host_cmddat_line_reset(host);
+
+ memset(&cmd, 0, sizeof(struct mmc_command));
+ cmd.opcode = 5;
+ cmd.arg = 0;
+ cmd.flags =
+ MMC_RSP_SPI_R4 | MMC_RSP_R4 | MMC_CMD_BCR;
+
+ mmc_wait_for_cmd(host->mmc, &cmd, 0);
+
+ pr_err("BHT ERR:%s: CMD7 CRC\n", __func__);
+ host_cmddat_line_reset(host);
+ return 0;
+ }
+ if (err == -ETIMEDOUT) {
+ pr_err("BHT ERR:%s: CMD7 timeout\n", __func__);
+ host_cmddat_line_reset(host);
+ return err;
+ }
+ return 0;
+}
+
+static bool gg_emulator_read_ext(struct sdhci_host *host, bool *card_status,
+ bool *read_status, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool card_ret = TRUE;
+ bool rd_ret = FALSE;
+
+ if (enter_exit_emulator_mode(host, TRUE) == 0)
+ ret = TRUE;
+ else
+ ret = FALSE;
+ if (!ret)
+ goto exit;
+
+ if (_gg_emulator_read_only(host, data, datalen) == 0)
+ rd_ret = TRUE;
+ else
+ rd_ret = FALSE;
+
+ if (enter_exit_emulator_mode(host, FALSE) == 0)
+ ret = TRUE;
+ else
+ ret = FALSE;
+
+ if (!ret)
+ goto exit;
+
+ if (gg_select_card_spec(host) == 0)
+ card_ret = TRUE;
+ else
+ card_ret = FALSE;
+
+ if (!rd_ret)
+ pr_err("BHT ERR:GGC read status error\n");
+
+exit:
+ if (!card_ret) {
+ pr_err("BHT ERR:GGC Emulator exit Fail!!\n");
+ ret = FALSE;
+ }
+
+ if (card_status)
+ *card_status = ret;
+
+ if (read_status)
+ *read_status = rd_ret;
+
+ if (rd_ret && !ret)
+ pr_err("BHT ERR:data read ok, but exit NG\n");
+ else if (!rd_ret && ret)
+ pr_err("BHT ERR:data read NG, but exit ok\n");
+
+ return ret;
+}
+
+static void _status_bit_2_bt(int tar, int *byt, int *bit)
+{
+ *byt = tar / 8;
+ *bit = tar % 8;
+}
+
+static u32 _read_status_data_read_register(u8 *cfg, struct t_gg_reg_strt *bts)
+{
+ u32 rv = 0;
+ u32 msk = bts->mask;
+ int byt = 0, bit = 0;
+ int i = 0;
+
+ do {
+ _status_bit_2_bt(bts->ofs + i, &byt, &bit);
+ if (cfg[byt] & (1 << bit))
+ rv |= 1 << i;
+
+ i++;
+ msk >>= 1;
+ if (msk == 0)
+ break;
+ } while (1);
+ return rv;
+}
+
+static bool ggc_read_registers_ext(struct sdhci_host *host,
+ bool *card_status, bool *read_status,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num)
+{
+ u8 get_idx = 0;
+ bool ret = FALSE;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+
+ if (read_status)
+ *read_status = FALSE;
+ if (card_status)
+ *card_status = FALSE;
+
+ memset(ggc->_cur_read_buf, 0, 512);
+ ret = gg_emulator_read_ext(host, card_status, read_status, ggc->_cur_read_buf, 512);
+ if (read_status == FALSE)
+ goto exit;
+
+ for (get_idx = 0; get_idx < num; get_idx++)
+ (gg_reg_arr + get_idx)->value =
+ _read_status_data_read_register(ggc->_cur_read_buf, (gg_reg_arr + get_idx));
+
+exit:
+ return ret;
+}
+
+static bool gg_emulator_read(struct sdhci_host *host, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool rd_ret = FALSE;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ rd_ret = _gg_emulator_read_only(host, data, datalen);
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = gg_select_card_spec(host);
+
+exit:
+ if (rd_ret)
+ pr_err("BHT ERR:GGC read status error\n");
+
+ if (ret)
+ pr_err("BHT ERR:GGC Emulator exit Fail!!\n");
+
+ if (rd_ret == 0 && ret) {
+ pr_err("BHT ERR:data read ok, but exit NG\n");
+ ret = 0;
+ }
+
+ if (rd_ret && ret == 0) {
+ pr_err("BHT ERR:data read NG, but exit ok\n");
+ ret = -1;
+ }
+
+ return ret ? FALSE : TRUE;
+}
+
+static bool _ggc_emulator_write_only(struct sdhci_host *host,
+ u8 *in_data, u32 datalen)
+{
+ struct mmc_host *mmc = host->mmc;
+ int rc = 0;
+ u8 *data1 = kzalloc(PAGE_SIZE, GFP_KERNEL);
+ struct mmc_request mrq = { 0 };
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct scatterlist sg;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!data1) {
+ pr_err("BHT MSG:gg write no memory\n");
+ rc = -ENOMEM;
+ goto out;
+ }
+
+ memcpy(data1, in_data, datalen);
+ sg_init_one(&sg, data1, 512);
+
+ cmd.opcode = MMC_WRITE_BLOCK;
+ cmd.arg = 0;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+ data.blksz = 512;
+ data.blocks = 1;
+ data.flags = MMC_DATA_WRITE;
+ data.timeout_ns = 1000 * 1000 * 1000;
+ data.sg = &sg;
+ data.sg_len = 1;
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+ mrq.stop = NULL;
+
+ mmc_wait_for_req(mmc, &mrq);
+
+ if (cmd.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+
+ kfree(data1);
+out:
+ return rc;
+}
+
+static bool gg_emulator_write(struct sdhci_host *host, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool wr_ret = FALSE;
+ u32 i = 0;
+ u32 reg;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ pr_debug("BHT MSG: dump config data\n");
+ for (i = 0; i < (datalen/sizeof(u32)); i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("BHT MSG:\tggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+
+ _ggc_emulator_write_only(host, data, datalen);
+ wr_ret = TRUE;
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = gg_select_card_spec(host);
+
+exit:
+ if (wr_ret == FALSE)
+ ret = FALSE;
+
+ if (ret == FALSE)
+ pr_err("BHT ERR:%s: GGC Emulator Write Fail!!\n", __func__);
+
+ return ret;
+}
+
+static bool get_gg_reg_cur(struct sdhci_host *host, u8 *data,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num)
+{
+ u8 get_idx = 0;
+ bool ret = FALSE;
+
+ /* read ggc register */
+ memset(data, 0, 512);
+ ret = gg_emulator_read(host, data, 512);
+
+ if (ret == FALSE)
+ goto exit;
+
+ /* read the offset bits value */
+ for (get_idx = 0; get_idx < num; get_idx++) {
+ (gg_reg_arr + get_idx)->value =
+ read_ram_bits_ofs_mask(data, (gg_reg_arr + get_idx));
+ }
+exit:
+ return ret;
+}
+
+static void chg_gg_reg_cur_val(struct ggc_platform_t *ggc, u8 *data,
+ struct t_gg_reg_strt *gg_reg_arr, u8 num, bool b_sav_chg)
+{
+ u8 chg_idx = 0;
+
+ for (chg_idx = 0; chg_idx < num; chg_idx++) {
+ /* modify the ggc register bit value */
+ cfg_write_bits_ofs_mask(data, (gg_reg_arr + chg_idx),
+ (gg_reg_arr + chg_idx)->value);
+ }
+
+ if (b_sav_chg)
+ set_gg_reg_cur_val(ggc, data, 64);
+}
+
+static void log_bin(u32 n)
+{
+ int i = 0;
+ u8 tb[33] = { 0 };
+
+ for (i = 0; i < 32; i++) {
+ if (n & (1 << i))
+ tb[i] = '1';
+ else
+ tb[i] = '0';
+ }
+ pr_debug("BHT MSG:bin:%s\n", tb);
+}
+
+static void phase_str(u8 *tb, u32 n)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (n & (1 << i))
+ tb[i] = '1';
+ else
+ tb[i] = '0';
+ }
+ tb[TUNING_PHASE_SIZE] = 0;
+}
+
+static int get_bit_number(u32 n)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (n & (1 << i))
+ cnt++;
+ }
+ return cnt;
+}
+
+static bool gg_emulator_write_ext(struct sdhci_host *host, bool *card_status, u8 *data, u32 datalen)
+{
+ bool ret = FALSE;
+ bool wr_ret = FALSE;
+
+ ret = enter_exit_emulator_mode(host, TRUE);
+ if (ret)
+ goto exit;
+
+ _ggc_emulator_write_only(host, data, datalen);
+ wr_ret = TRUE;
+
+ ret = enter_exit_emulator_mode(host, FALSE);
+ if (ret)
+ goto exit;
+
+ ret = (gg_select_card_spec(host) == 0) ? TRUE : FALSE;
+ if (ret == FALSE) {
+ if (card_status)
+ *card_status = FALSE;
+ }
+
+exit:
+ if (wr_ret == FALSE)
+ ret = FALSE;
+
+ if (ret == FALSE)
+ pr_err("BHT ERR:%s: GGC Emulator Write Fail!!\n", __func__);
+
+ return ret;
+}
+
+static bool ggc_set_output_tuning_phase_ext(struct sdhci_host *host,
+ bool *card_status, int sela, int selb)
+{
+ bool ret = TRUE;
+ u8 data[512] = { 0 };
+ struct t_gg_reg_strt gg_reg_arr[8];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_sela_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_sela_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_selb_100m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_200m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.internl_tuning_en_100m,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.internl_tuning_en_200m,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = sela;
+ gg_reg_arr[1].value = sela;
+ gg_reg_arr[2].value = selb;
+ gg_reg_arr[3].value = selb;
+ gg_reg_arr[4].value = 1;
+ gg_reg_arr[5].value = 1;
+ gg_reg_arr[6].value = 1;
+ gg_reg_arr[7].value = 1;
+ if (card_status)
+ *card_status = TRUE;
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 8, TRUE);
+ ret = gg_emulator_write_ext(host, card_status, data, 512);
+ return ret;
+}
+
+static bool gg_fix_output_tuning_phase(struct sdhci_host *host, int sela, int selb)
+{
+ u8 data[512] = { 0 };
+ struct t_gg_reg_strt gg_reg_arr[10];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("BHT MSG: %s - sela dll: %x, selb dll: %x\n", __func__, sela,
+ selb);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_sela_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_sela_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_selb_100m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_200m_cfg_en,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.internl_tuning_en_100m,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.internl_tuning_en_200m,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = sela;
+ gg_reg_arr[1].value = sela;
+ gg_reg_arr[2].value = selb;
+ gg_reg_arr[3].value = selb;
+ gg_reg_arr[4].value = 1;
+ gg_reg_arr[5].value = 1;
+ gg_reg_arr[6].value = 0;
+ gg_reg_arr[7].value = 0;
+
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 8, TRUE);
+
+ return gg_emulator_write(host, data, 512);
+}
+
+static void gen_array_data(u32 low32, u32 high32, u32 *ptw)
+{
+ u8 tu_res_per[6][TUNING_PHASE_SIZE];
+ u8 i = 0, j = 0;
+ u8 i_mode = 0;
+ u32 tw = 0;
+
+ memset(tu_res_per, 1, sizeof(tu_res_per));
+ for (i = 0; i < 64; i++) {
+ u32 tmp_data = (i < 32) ? low32 : high32;
+
+ tu_res_per[i / TUNING_PHASE_SIZE][i % TUNING_PHASE_SIZE] =
+ (tmp_data & (1 << (i % 32))) >> (i % 32);
+ }
+
+ for (i_mode = 0; i_mode < TUNING_PHASE_SIZE; i_mode++) {
+ for (j = 0; j < 6; j++) {
+ if (tu_res_per[j][i_mode] != 0)
+ tw |= (1 << i_mode);
+ else {
+ tw &= ~(1 << i_mode);
+ break;
+ }
+ }
+ }
+ if (ptw)
+ *ptw = tw;
+}
+
+static bool sw_calc_tuning_result(struct sdhci_host *host, u32 *tx_selb,
+ u32 *all_selb, u64 *raw_tx_selb)
+{
+ bool ret = FALSE;
+ u8 data[512] = { 0 };
+ u32 selb_status_tx_low32 = 0, selb_status_tx_high32 = 0;
+ u32 selb_status_ggc_low32 = 0, selb_status_ggc_high32 = 0;
+ struct t_gg_reg_strt gg_reg_arr[6];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.pha_stas_tx_low32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.pha_stas_tx_high32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.pha_stas_rx_low32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.pha_stas_rx_high32, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_sela_after_mask, sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_after_mask, sizeof(struct t_gg_reg_strt));
+
+ ret = get_gg_reg_cur(host, data, gg_reg_arr, 6);
+
+ if (ret == TRUE) {
+ selb_status_tx_low32 = gg_reg_arr[0].value;
+ pr_debug("BHT MSG:[205-236]:\n");
+ log_bin(selb_status_tx_low32);
+ selb_status_tx_high32 = gg_reg_arr[1].value;
+ pr_debug("BHT MSG:[237-268]:\n");
+ log_bin(selb_status_tx_high32);
+ selb_status_ggc_low32 = gg_reg_arr[2].value;
+ pr_debug("BHT MSG:[14-45]:\n");
+ log_bin(selb_status_ggc_low32);
+ selb_status_ggc_high32 = gg_reg_arr[3].value;
+ pr_debug("BHT MSG:[46-77]:\n");
+ log_bin(selb_status_ggc_high32);
+ pr_debug("BHT MSG:dll sela after mask=%xh\n", gg_reg_arr[4].value);
+ pr_debug("BHT MSG:dll selb after mask=%xh\n", gg_reg_arr[5].value);
+
+ if (raw_tx_selb) {
+ *raw_tx_selb = gg_reg_arr[1].value;
+ (*raw_tx_selb) <<= 32;
+ *raw_tx_selb += gg_reg_arr[0].value;
+ pr_debug("BHT MSG:raw_tx_selb:%llxh\n", *raw_tx_selb);
+ }
+
+ if (tx_selb) {
+ gen_array_data(gg_reg_arr[0].value, gg_reg_arr[1].value,
+ tx_selb);
+ pr_debug("BHT MSG:tx_selb:%xh\n", *tx_selb);
+ }
+ if (all_selb) {
+ gen_array_data(gg_reg_arr[2].value, gg_reg_arr[3].value,
+ all_selb);
+ pr_debug("BHT MSG:all_selb:%xh\n", *all_selb);
+ }
+ }
+
+ return ret;
+}
+
+static bool gg_tuning_result(struct sdhci_host *host, u32 *tx_selb, u32 *all_selb,
+ u64 *raw_tx_selb)
+{
+ host_cmddat_line_reset(host);
+ return sw_calc_tuning_result(host, tx_selb, all_selb, raw_tx_selb);
+}
+
+static u64 GENERATE_64_IDX_VALUE(int sft)
+{
+ u64 val = 1;
+
+ return val << sft;
+}
+
+static bool is_bus_mode_sdr104(struct sdhci_host *host)
+{
+ bool ret = FALSE;
+
+ if (host->timing == MMC_TIMING_UHS_SDR104)
+ ret = TRUE;
+
+ return ret;
+}
+
+static bool _check_bus_mode(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+
+ if (is_bus_mode_sdr104(host))
+ ggc->cur_bus_mode = &vendor_host->ggc.sdr104;
+ else
+ ggc->cur_bus_mode = &vendor_host->ggc.sdr50;
+
+ return true;
+}
+
+static void tx_selb_failed_history_update(struct sdhci_host *host, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+
+ vendor_host->ggc.cur_bus_mode->tx_selb_failed_history &= val;
+}
+
+static u32 tx_selb_failed_history_get(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+
+ return vendor_host->ggc.cur_bus_mode->tx_selb_failed_history;
+}
+
+static void tx_selb_failed_tb_update(struct sdhci_host *host, int sela, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+ vendor_host->ggc.cur_bus_mode->tx_selb_tb[sela] &= val;
+}
+
+static u32 tx_selb_failed_tb_get(struct sdhci_host *host, int sela)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 value = 0;
+
+ _check_bus_mode(host);
+
+ if (is_bus_mode_sdr104(host))
+ value = vendor_host->ggc.sdr104.tx_selb_tb[sela];
+ else
+ value = vendor_host->ggc.sdr50.tx_selb_tb[sela];
+
+ return value;
+}
+
+static void all_selb_failed_tb_update(struct sdhci_host *host, int sela, u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ _check_bus_mode(host);
+ vendor_host->ggc.cur_bus_mode->all_selb_tb[sela] &= val;
+}
+
+static u32 all_selb_failed_tb_get(struct sdhci_host *host, int sela)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 val;
+
+ _check_bus_mode(host);
+
+ val = vendor_host->ggc.cur_bus_mode->all_selb_tb[sela];
+
+ return val;
+}
+
+static void chk_phase_window(u8 *tuning_win, u8 *mid_val, u8 *max_pass_win)
+{
+ u8 tuning_pass[TUNING_PHASE_SIZE + 32];
+ u8 tuning_pass_start[TUNING_PHASE_SIZE + 32];
+ u8 tuning_pass_num_max = 0;
+ u8 first_0 = 0;
+ u8 i = 0, j = 0;
+ u8 i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 1, sizeof(tuning_pass));
+ memset(tuning_pass_start, 1, sizeof(tuning_pass_start));
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = (first_0 + i) % TUNING_PHASE_SIZE;
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0)
+ pr_err
+ ("Get max pass window fail, there is no any pass phase!!\n");
+ else {
+ *max_pass_win = tuning_pass_num_max - 1;
+ tuning_pass_num_max /= 2;
+ selb_mode = tuning_pass_start[i_mode] + tuning_pass_num_max;
+ if ((*max_pass_win % 2 == 0))
+ selb_mode += 1;
+ selb_mode %= TUNING_PHASE_SIZE;
+ }
+
+ *mid_val = selb_mode;
+}
+
+static void dump_array(u8 *tb)
+{
+ int i = 0;
+ u8 str[12] = { 0 };
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ str[i] = tb[i] + '0';
+}
+
+static void bits_generate_array(u8 *tb, u32 v)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if ((v & (1 << i)))
+ tb[i] = 1;
+ else
+ tb[i] = 0;
+ }
+ dump_array(tb);
+}
+
+static void chk_arr_max_win(u8 *tuning_win, u8 first_i, u8 *mid_val,
+ u8 *first_val, u8 *max_pass_win, struct chk_type_t type)
+{
+ u8 tuning_pass[TUNING_PHASE_SIZE];
+ u8 tuning_pass_start[TUNING_PHASE_SIZE];
+ u8 tuning_pass_num_max = 0;
+ u8 first_0 = 0;
+ u8 i = 0, j = 0;
+ u8 i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 1, sizeof(tuning_pass));
+ memset(tuning_pass_start, 1, sizeof(tuning_pass_start));
+
+ if (type.first_valid)
+ first_0 = first_i;
+ else {
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = (first_0 + i) % TUNING_PHASE_SIZE;
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0)
+ pr_err
+ ("Get max pass window fail, there is no any pass phase!!\n");
+ else {
+ *max_pass_win = tuning_pass_num_max - 1;
+ tuning_pass_num_max /= 2;
+ if (first_val)
+ *first_val = tuning_pass_start[i_mode];
+ selb_mode = tuning_pass_start[i_mode] + tuning_pass_num_max;
+ if ((*max_pass_win % 2 == 0) && (type.right_valid)
+ )
+ selb_mode += 1;
+ selb_mode %= TUNING_PHASE_SIZE;
+ }
+
+ *mid_val = selb_mode;
+}
+
+void no_fail_p(u8 *tuning_win, u8 *mid_val, u8 *max_pass_win, u8 *first_val)
+{
+ struct chk_type_t type;
+ u8 first_0 = 0;
+
+ memset((u8 *)&type, 0, sizeof(struct chk_type_t));
+
+ type.first_valid = 0;
+ type.right_valid = 1;
+ type.record_valid = 0;
+
+ chk_arr_max_win(tuning_win, first_0, mid_val, first_val,
+ max_pass_win, type);
+}
+
+static int ggc_get_selx_weight(u32 val)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i))
+ cnt++;
+ }
+ return cnt;
+}
+
+void tx_selb_calculate_valid_phase_range(u32 val, int *start,
+ int *pass_cnt)
+{
+ int i = 0, flg = 0;
+
+ *pass_cnt = ggc_get_selx_weight(val);
+ for (i = 0; i < (TUNING_PHASE_SIZE * 2); i++) {
+ if ((GET_TRUNING_RING_IDX_VALUE(val, i)) == 0 && (flg == 0))
+ flg = 1;
+ if ((flg == 1) && GET_TRUNING_RING_IDX_VALUE(val, i)) {
+ *start = TRUNING_RING_IDX(i);
+ break;
+ }
+ }
+}
+
+bool ggc_update_default_selb_phase_tuning_cnt(struct sdhci_host *host, int selb,
+ int tuning_cnt)
+{
+ struct t_gg_reg_strt gg_reg_arr[3];
+ u8 data[512];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+
+ pr_debug("BHT MSG: selb:%xh,tuning_cnt:%xh\n", selb,
+ tuning_cnt);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.dll_selb_100m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.dll_selb_200m_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.cmd19_cnt_cfg,
+ sizeof(struct t_gg_reg_strt));
+
+ gg_reg_arr[0].value = selb;
+ gg_reg_arr[1].value = selb;
+ gg_reg_arr[2].value = tuning_cnt;
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 3, TRUE);
+
+ return TRUE;
+}
+
+static void _ggc_update_cur_setting_for_sw_selb_tuning(struct sdhci_host *host,
+ u32 val)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int start = 0, pass_cnt = 0;
+
+ tx_selb_calculate_valid_phase_range(val, &start, &pass_cnt);
+ pr_debug("BHT MSG:%s %x %x %x\n", __func__, val, start, pass_cnt);
+ ggc_update_default_selb_phase_tuning_cnt(host, start, pass_cnt); //update
+ vendor_host->ggc.ggc_sw_selb_tuning_first_selb = start;
+}
+
+int sdhci_bht_sdr50_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+
+ u8 phase, *data_buf;
+ int size = 64;
+ int rc = 0;
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__);
+
+ data_buf = kmalloc(size, GFP_KERNEL);
+
+ phase = 0;
+ do {
+ struct mmc_command cmd = { 0 };
+ struct mmc_data data = { 0 };
+ struct mmc_request mrq = {
+ .cmd = &cmd,
+ .data = &data
+ };
+ struct scatterlist sg;
+
+ cmd.opcode = opcode;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+
+ data.blksz = size;
+ data.blocks = 1;
+ data.flags = MMC_DATA_READ;
+ data.timeout_ns = 30 * 1000 * 1000; /* 30ms */
+
+ data.sg = &sg;
+ data.sg_len = 1;
+ sg_init_one(&sg, data_buf, size);
+ memset(data_buf, 0, size);
+ host_cmddat_line_reset(host);
+ mmc_wait_for_req(mmc, &mrq);
+
+ if (cmd.error) {
+ if (cmd.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+ if (cmd.error == -ETIMEDOUT && phase == 0) {
+ pr_err("BHT ERR:cmd19 timeout\n");
+ rc = -ETIMEDOUT;
+ goto kfree;
+ }
+ }
+
+ if (data.error) {
+ if (data.error == -EILSEQ)
+ vendor_host->ggc.sdr50_notuning_crc_error_flag = 1;
+ }
+ } while (++phase < 16);
+
+kfree:
+ kfree(data_buf);
+
+ return rc;
+}
+
+int get_config_sela_setting(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (is_bus_mode_sdr104(host))
+ return vendor_host->ggc.def_sela_200m;
+ else
+ return vendor_host->ggc.def_sela_100m;
+}
+
+int get_config_selb_setting(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (is_bus_mode_sdr104(host))
+ return vendor_host->ggc.def_selb_200m;
+ else
+ return vendor_host->ggc.def_selb_100m;
+}
+
+u32 get_all_sela_status(struct sdhci_host *host, u32 target_selb)
+{
+ u32 all_sela = 0;
+ u32 all_selb = 0;
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ all_selb = all_selb_failed_tb_get(host, i);
+ if (all_selb & (1 << target_selb))
+ all_sela |= 1 << i;
+ }
+ return all_sela;
+}
+
+int get_pass_window_weight(u32 val)
+{
+ int i = 0;
+ int cnt = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i))
+ cnt++;
+ }
+ return cnt;
+}
+
+int get_sela_nearby_pass_window(u32 sela, u32 base)
+{
+
+ int i = 0;
+ int idx = base;
+ int cnt = 0;
+
+ if (GET_IDX_VALUE(sela, idx) == 0)
+ return 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(sela, idx)) {
+ idx++;
+ idx %= TUNING_PHASE_SIZE;
+ } else {
+ break;
+ }
+ }
+
+ if (idx == 0)
+ idx = 0xa;
+ else
+ idx--;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(sela, idx)) {
+ cnt++;
+ if (idx == 0)
+ idx = 0xa;
+ else
+ idx--;
+ } else {
+ break;
+ }
+ }
+ return cnt;
+}
+
+int get_left_one_sel(int base)
+{
+ if (base == 0)
+ return 0xa;
+ else
+ return base - 1;
+}
+
+int get_right_one_sel(int base)
+{
+ if (base == 0xa)
+ return 0x0;
+ else
+ return base + 1;
+}
+
+int get_dif(int x, int y)
+{
+ int dif = 0;
+
+ if (y > x)
+ dif = y - x;
+ else
+ dif = x - y;
+
+ return dif;
+}
+
+static int update_selb(struct sdhci_host *host, int target_selb)
+{
+ return target_selb;
+}
+
+static int ggc_get_10case_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val,
+ TRUNING_RING_IDX(i + TUNING_PHASE_SIZE -
+ 1))) {
+ return i;
+ }
+ }
+
+ return -1;
+}
+
+static u32 ggc_get_01case_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val, TRUNING_RING_IDX(i + 1))) {
+ return i;
+ }
+ }
+
+ return -1;
+}
+
+static int ggc_get_next_1_index(u32 val, int pos)
+{
+ int i = 0;
+
+ pos = pos % TUNING_PHASE_SIZE;
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, (pos+i)%TUNING_PHASE_SIZE))
+ break;
+ }
+ if (GET_IDX_VALUE(val, (pos+i)%TUNING_PHASE_SIZE))
+ return (pos+i)%TUNING_PHASE_SIZE;
+ else
+ return -1;
+}
+
+static u32 ggc_get_01case_1_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0
+ && GET_IDX_VALUE(val, TRUNING_RING_IDX(i + 1))) {
+ return TRUNING_RING_IDX(i + 1);
+ }
+ }
+
+ return -1;
+}
+
+static int ggc_get_first_0_index(u32 val)
+{
+ int i = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(val, i) == 0)
+ return i;
+ }
+ pr_debug("BHT MSG:oops-not find 0 index\n");
+ return 0;
+}
+
+static int _tx_selb_inject_policy(int tx_selb, int org_selb)
+{
+ int group_pos[TUNING_PHASE_SIZE+1][3];
+ int group_cnt = 0;
+ int max_len_group = 0;
+ int max_len = 0;
+ int i, j, cnt;
+ int zero_start, zero_end, sel;
+
+ if ((org_selb & BIT_PASS_MASK) != BIT_PASS_MASK) {
+ sel = tx_selb;
+ zero_start = ggc_get_10case_0_index(sel);
+ sel &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (zero_start));
+ zero_end = ggc_get_01case_0_index(sel);
+ sel &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (zero_end));
+ if (sel != (sel & tx_selb)) {
+ pr_err
+ ("tx selb reinject exception case :not adjacent phase\n");
+ pr_err("BHT ERR:selb_failed range:%xh ,new tx_selb:%x\n",
+ org_selb, tx_selb);
+ }
+ org_selb &= tx_selb;
+ } else {
+ cnt = ggc_get_selx_weight(~tx_selb);
+ pr_debug("BHT MSG:%d\n", cnt);
+ switch (cnt) {
+ case 1:
+ i = ggc_get_first_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (i));
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (i));
+
+ break;
+ case 2:
+ i = ggc_get_10case_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_left_one_sel
+ (i));
+ i = ggc_get_01case_0_index(tx_selb);
+ tx_selb &=
+ ~GENERATE_TRUNING_RING_IDX_VALUE(get_right_one_sel
+ (i));
+ break;
+ default:
+ pr_debug("BHT MSG:>= 3 point case\n");
+ }
+ org_selb &= tx_selb;
+ }
+
+ pr_debug("BHT MSG:will check continuous 0bits: 0x%x\n", org_selb);
+
+ memset(group_pos, 0, sizeof(group_pos));
+ for (i = ggc_get_01case_1_index(org_selb);
+ i < TUNING_PHASE_SIZE && i >= 0 && group_cnt < TUNING_PHASE_SIZE;) {
+ for (j = 1; j < TUNING_PHASE_SIZE; j++) {
+ if (GET_TRUNING_RING_IDX_VALUE(org_selb, i+j) != 0)
+ continue;
+ else
+ break;
+ }
+ group_pos[group_cnt][0] = i;
+ group_pos[group_cnt][1] = (i + j - 1) % TUNING_PHASE_SIZE;
+ group_pos[group_cnt][2] = j;
+ group_cnt++;
+ if (group_pos[group_cnt-1][0] > group_pos[group_cnt-1][1])
+ break;
+ i = ggc_get_next_1_index(org_selb, (i+j)%TUNING_PHASE_SIZE);
+ for (j = 0; j < group_cnt; j++) {
+ if (i == group_pos[j][0])
+ break;
+ }
+ if (j < group_cnt)
+ break;
+ }
+
+ if (group_cnt > 1) {
+ pr_err("BHT ERR:After inject, selb 0x%x has %d continuous 0 bits\n",
+ org_selb, group_cnt);
+
+ for (i = 0; i < group_cnt; i++) {
+ if (max_len < group_pos[i][2]) {
+ max_len = group_pos[i][2];
+ max_len_group = i;
+ }
+ }
+ for (i = (group_pos[max_len_group][1] + 1) % TUNING_PHASE_SIZE;
+ i != group_pos[max_len_group][0]; i = (i+1)%TUNING_PHASE_SIZE) {
+ org_selb &= ~(1 << i);
+ }
+ pr_err("BHT ERR:After merge incontious 0 group, selb changed to 0x%x\n", org_selb);
+ } else if (group_cnt > 0) {
+ pr_err("BHT ERR:After merge incontious 0 group, selb = 0x%x\n", org_selb);
+ } else {
+ pr_err("BHT ERR:selb 0x%x has no bit is 0\n", org_selb);
+ }
+
+ return org_selb;
+}
+
+void tx_selb_inject_policy(struct sdhci_host *host, int tx_selb)
+{
+
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ pr_debug("BHT MSG:before inject, failed ragen 0x%x, tx_selb 0x%x\n",
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, tx_selb);
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range =
+ _tx_selb_inject_policy(tx_selb, vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ tx_selb_failed_history_update(host, vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ pr_debug("BHT MSG:after inject %xh range:%xh\n", tx_selb,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ if (is_bus_mode_sdr104(host))
+ vendor_host->ggc.sdr104.fail_phase = vendor_host->ggc.ggc_cmd_tx_selb_failed_range;
+ else
+ vendor_host->ggc.sdr50.fail_phase = vendor_host->ggc.ggc_cmd_tx_selb_failed_range;
+}
+
+int get_selb_failure_point(int start, u64 raw_tx_selb, int tuning_cnt)
+{
+ int last = start + (tuning_cnt - 1);
+ int i = 0;
+ int j = 0;
+ int phase = start;
+ int vct = BIT_PASS_MASK;
+
+ pr_debug("BHT MSG:%s start:%d tuning_cnt:%d\n", __func__, start,
+ tuning_cnt);
+
+ for (i = 0; i < tuning_cnt; i++) {
+ if ((raw_tx_selb & GENERATE_64_IDX_VALUE(last - i)) == 0)
+ break;
+ }
+ if (i == tuning_cnt) {
+ phase = last % TUNING_PHASE_SIZE;
+ vct &= (~(1 << phase));
+ goto exit;
+ }
+
+ for (i = 0; i < tuning_cnt; i++) {
+ if ((raw_tx_selb & GENERATE_64_IDX_VALUE(last - i)) != 0)
+ break;
+ }
+ for (j = i - 2; j >= 0; j--)
+ raw_tx_selb |= (1 << (last - j));
+
+ for (j = 0; j < tuning_cnt; j++) {
+ if (0 == (raw_tx_selb & GENERATE_64_IDX_VALUE(last - j)))
+ vct &= (~(1 << (last-j)));
+ }
+
+exit:
+ pr_debug("BHT MSG:%s: after adjust raw_tx_selb: 0x%llx, vct 0x%x\n",
+ __func__, raw_tx_selb, vct);
+
+ return vct;
+}
+
+bool selx_failure_point_exist(u32 val)
+{
+ return (val & BIT_PASS_MASK) != BIT_PASS_MASK;
+}
+
+static int _bits_vct_get_left_index(int base)
+{
+ return TRUNING_RING_IDX(base + TUNING_PHASE_SIZE - 1);
+}
+
+int _get_best_window_phase(u32 vct, int *pmax_pass_win, int shif_left_flg)
+{
+ u8 tuning_win[TUNING_PHASE_SIZE] = { 0 };
+ u8 tuning_pass[TUNING_PHASE_SIZE];
+ int tuning_pass_start[TUNING_PHASE_SIZE];
+ int tuning_pass_num_max = 0;
+ int first_0 = 0;
+ int i = 0, j = 0;
+ int i_mode = 0, selb_mode = 0;
+
+ memset(tuning_pass, 0, sizeof(tuning_pass));
+ memset(tuning_pass_start, 0, sizeof(tuning_pass_start));
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(vct, i))
+ tuning_win[i] = 1;
+ else
+ tuning_win[i] = 0;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_win[i] == 0) {
+ first_0 = i;
+ break;
+ }
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ i_mode = TRUNING_RING_IDX(first_0 + i);
+ if (tuning_win[i_mode] == 1)
+ tuning_pass[j]++;
+ else if (tuning_pass[j])
+ j++;
+ if (tuning_pass[j] == 1)
+ tuning_pass_start[j] = i_mode;
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (tuning_pass_num_max < tuning_pass[i]) {
+ tuning_pass_num_max = tuning_pass[i];
+ i_mode = i;
+ }
+ }
+
+ if (tuning_pass_num_max == 0) {
+ pr_err("BHT ERR:###### Get max pass window fail, there is no any pass phase!!\n");
+ selb_mode = 0;
+ } else {
+ if (tuning_pass_num_max % 2) {
+ selb_mode = tuning_pass_start[i_mode] + (tuning_pass_num_max - 1) / 2;
+ } else {
+ selb_mode = tuning_pass_start[i_mode] + (tuning_pass_num_max) / 2;
+ if (shif_left_flg) {
+ selb_mode = _bits_vct_get_left_index(selb_mode);
+ pr_debug("BHT MSG:shift left index\n");
+ }
+ }
+ selb_mode = TRUNING_RING_IDX(selb_mode);
+ }
+ if (pmax_pass_win)
+ *pmax_pass_win = tuning_pass_num_max;
+
+ return selb_mode;
+}
+
+
+int get_best_window_phase(u32 vct, int *pmax_pass_win)
+{
+ return _get_best_window_phase(vct, pmax_pass_win, 0);
+}
+
+static int _ggc_get_suitable_selb_for_next_tuning(struct sdhci_host *host)
+{
+ int selb = 0;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 inj_tx_selb = BIT_PASS_MASK;
+
+ if (selx_failure_point_exist(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) {
+ selb = vendor_host->ggc.ggc_sw_selb_tuning_first_selb;
+ } else {
+ pr_debug("BHT MSG:manual inject for all pass case\n");
+ if (is_bus_mode_sdr104(host))
+ inj_tx_selb &= SDR104_MANUAL_INJECT;
+ else
+ inj_tx_selb &= SDR50_MANUAL_INJECT;
+
+ pr_debug("BHT MSG:manual inject for all pass case, inj_tx_selb=0x%x\n",
+ inj_tx_selb);
+ selb = get_best_window_phase(inj_tx_selb, NULL);
+ pr_debug("BHT MSG:select selb %d for all pass case\n", selb);
+ }
+ return selb;
+}
+
+static int ggc_get_tuning_cnt_from_buffer(struct sdhci_host *host)
+{
+ int cnt = 0;
+ u8 data[512];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ cnt = (int)cfg_read_bits_ofs_mask(data, &vendor_host->ggc.cmd19_cnt_cfg);
+
+ pr_debug("BHT MSG:tuning cnt=%d\n", cnt);
+ return cnt;
+}
+
+bool ggc_hw_inject_ext(struct sdhci_host *host, bool *card_status,
+ u32 sel200, u32 sel100, bool writetobh201)
+{
+ bool ret = TRUE;
+ u8 data[512];
+ struct t_gg_reg_strt gg_reg_arr[10];
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u32 i = 0;
+ u32 reg;
+
+ pr_debug("BHT MSG:%s sel200:%xh,sel100:%xh\n", __func__, sel200, sel100);
+ get_gg_reg_cur_val(&vendor_host->ggc, data, 64);
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.inject_failure_for_tuning_enable_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.inject_failure_for_200m_tuning_cfg,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.inject_failure_for_100m_tuning_cfg,
+ sizeof(struct t_gg_reg_strt));
+ gg_reg_arr[0].value = 1;
+ gg_reg_arr[1].value = sel200;
+ gg_reg_arr[2].value = sel100;
+
+ chg_gg_reg_cur_val(&vendor_host->ggc, data, gg_reg_arr, 3, TRUE);
+ if (writetobh201)
+ ret = gg_emulator_write_ext(host, card_status, data, 512);
+ else {
+ pr_debug("BHT MSG:%s: dump config data instead write to bh201\n", __func__);
+ for (i = 0; i < 128; i++) {
+ memcpy(®, data+i*sizeof(u32), sizeof(u32));
+ pr_debug("BHT MSG: ggc_reg32[%03d]=0x%08x\n", i, reg);
+ }
+ }
+ return ret;
+}
+
+bool _ggc_hw_inject_may_recursive(struct sdhci_host *host, u32 sel200,
+ u32 sel100, int max_recur, bool writetobh201)
+{
+ bool ret = TRUE, card_status = TRUE;
+ int selb = BIT_PASS_MASK;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ ret = ggc_hw_inject_ext(host, &card_status, vendor_host->ggc.ggc_cmd_tx_selb_failed_range,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, writetobh201);
+ pr_debug("BHT MSG:ret:%x\n", ret);
+ if ((ret == FALSE) && (card_status == FALSE)) {
+ pr_debug("BHT MSG:inject again when hw inject\n");
+ selb &= ~GENERATE_IDX_VALUE(vendor_host->ggc.ggc_sw_selb_tuning_first_selb);
+ tx_selb_inject_policy(host, selb);
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+
+ if (((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) >= 5)) {
+ pr_err("BHT ERR:pass windows too small,reinit recursive\n");
+ return FALSE;
+ }
+
+ if (max_recur--)
+ return _ggc_hw_inject_may_recursive(host,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range, max_recur, writetobh201);
+ else
+ return FALSE;
+ } else
+ return TRUE;
+}
+
+bool ggc_hw_inject_may_recursive(struct sdhci_host *host, u32 sel200,
+ u32 sel100, bool writetobh201)
+{
+ return _ggc_hw_inject_may_recursive(host, sel200, sel100, 4, writetobh201);
+}
+
+bool get_next_dll_voltage(int cur, int *next, u32 *dll_voltage_unlock_cnt,
+ int *dll_voltage_scan_map)
+{
+ int min_idx = 0, cur_cnt = 0, next_cnt = 0;
+ int cur_flg = 0;
+ int i = 0;
+ u8 ret = 0;
+
+ pr_warn("BHT WARN:dll_voltage_unlock_cnt:%x %x %x %x\n",
+ dll_voltage_unlock_cnt[0], dll_voltage_unlock_cnt[1],
+ dll_voltage_unlock_cnt[2], dll_voltage_unlock_cnt[3]);
+ pr_warn("BHT WARN:dll_voltage_scan_map:%x %x %x %x\n",
+ dll_voltage_scan_map[0], dll_voltage_scan_map[1],
+ dll_voltage_scan_map[2], dll_voltage_scan_map[3]);
+ for (i = 1; i < 4; i++) {
+ if (cur_flg == 0) {
+ if (dll_voltage_scan_map[(cur + i) % 4] != 0)
+ continue;
+ cur_cnt = dll_voltage_unlock_cnt[(cur + i) % 4];
+ cur_flg = 1;
+ min_idx = (cur + i) % 4;
+ continue;
+ } else {
+ if (dll_voltage_scan_map[(cur + i) % 4] != 0)
+ continue;
+ next_cnt = dll_voltage_unlock_cnt[(cur + i) % 4];
+ if (cur_cnt > next_cnt) {
+ cur_cnt = next_cnt;
+ min_idx = (cur + i) % 4;
+ }
+ }
+ }
+ if (cur_flg == 0) {
+ pr_err("BHT ERR:no find available voltage\n");
+ ret = FALSE;
+ } else {
+ *next = min_idx;
+ pr_err("BHT ERR:next available voltage %d\n", min_idx);
+ ret = TRUE;
+ }
+ return ret;
+}
+
+bool ggc_sw_calc_tuning_result(struct sdhci_host *host, bool *card_status,
+ bool *read_status, u32 *tx_selb, u32 *all_selb, u64 *raw_tx_selb)
+{
+ bool ret = FALSE;
+ bool card_ret = FALSE;
+ bool read_ret = FALSE;
+ u32 selb_status_tx_low32 = 0, selb_status_tx_high32 = 0;
+ u32 selb_status_ggc_low32 = 0, selb_status_ggc_high32 = 0;
+ struct t_gg_reg_strt gg_reg_arr[8] = {{0}};
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+
+ memcpy(&gg_reg_arr[0], &vendor_host->ggc.pha_stas_tx_low32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[1], &vendor_host->ggc.pha_stas_tx_high32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[2], &vendor_host->ggc.pha_stas_rx_low32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[3], &vendor_host->ggc.pha_stas_rx_high32,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[4], &vendor_host->ggc.dll_sela_after_mask,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[5], &vendor_host->ggc.dll_selb_after_mask,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[6], &vendor_host->ggc.dll_delay_100m_backup,
+ sizeof(struct t_gg_reg_strt));
+ memcpy(&gg_reg_arr[7], &vendor_host->ggc.dll_delay_200m_backup,
+ sizeof(struct t_gg_reg_strt));
+
+ ret = ggc_read_registers_ext(host, &card_ret, &read_ret, gg_reg_arr, 8);
+ if (read_ret == TRUE) {
+ selb_status_tx_low32 = gg_reg_arr[0].value;
+ pr_debug("BHT MSG:[205-236]:\n");
+ log_bin(selb_status_tx_low32);
+ selb_status_tx_high32 = gg_reg_arr[1].value;
+ pr_debug("BHT MSG:[237-268]:\n");
+ log_bin(selb_status_tx_high32);
+ selb_status_ggc_low32 = gg_reg_arr[2].value;
+ pr_debug("BHT MSG:[14-45]:\n");
+ log_bin(selb_status_ggc_low32);
+ selb_status_ggc_high32 = gg_reg_arr[3].value;
+ pr_debug("BHT MSG:[46-77]:\n");
+ log_bin(selb_status_ggc_high32);
+ pr_debug("BHT MSG:dll sela after mask=%xh", gg_reg_arr[4].value);
+ pr_debug("BHT MSG:dll selb after mask=%xh", gg_reg_arr[5].value);
+
+ if (raw_tx_selb) {
+ *raw_tx_selb = gg_reg_arr[1].value;
+ (*raw_tx_selb) <<= 32;
+ *raw_tx_selb += gg_reg_arr[0].value;
+ pr_debug("BHT MSG:raw_tx_selb:%llxh\n", *raw_tx_selb);
+ }
+
+ if (tx_selb) {
+ gen_array_data(gg_reg_arr[0].value, gg_reg_arr[1].value,
+ tx_selb);
+ pr_debug("BHT MSG:tx_selb:%xh\n", *tx_selb);
+ }
+ if (all_selb) {
+ gen_array_data(gg_reg_arr[2].value, gg_reg_arr[3].value,
+ all_selb);
+ pr_debug("BHT MSG:all_selb:%xh\n", *all_selb);
+ }
+ }
+
+ if (read_status)
+ (*read_status) = read_ret;
+ if (card_status)
+ (*card_status) = card_ret;
+
+ if (card_status && read_status)
+ pr_debug("BHT MSG:card_status,read_status:%x %x\n", *card_status, *read_status);
+ return ret;
+}
+
+bool _ggc_calc_cur_sela_tuning_result(struct sdhci_host *host, int cur_sela, int start_selb)
+{
+ bool read_status = FALSE;
+ bool card_status = FALSE;
+ bool ret = TRUE;
+ u32 tx_selb, all_selb;
+ u64 raw_tx_selb = 0;
+ bool retuning_flg = FALSE;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ int selb;
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+ enum tuning_stat_et *psela_tuning_result = ggc->ggc_sela_tuning_result;
+
+ ret = ggc_sw_calc_tuning_result(host, &card_status,
+ &read_status, &tx_selb, &all_selb, &raw_tx_selb);
+
+ if (card_status == FALSE) {
+ if (read_status == TRUE) {
+ selb = get_selb_failure_point(start_selb, raw_tx_selb,
+ ggc_get_tuning_cnt_from_buffer(host));
+ pr_debug("BHT MSG:inject selb %03x for CMD7 read timeout\n", selb);
+ tx_selb_inject_policy(host, selb);
+ } else {
+ pr_debug("BHT MSG:%s dll:%xh read status failed\n",
+ __func__, cur_sela);
+ }
+ ret = FALSE;
+ goto exit;
+ } else {
+ if (read_status == TRUE) {
+ if (selx_failure_point_exist(tx_selb)) {
+ if ((11-get_bit_number(tx_selb)) <= 3) {
+ tx_selb_inject_policy(host, tx_selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ } else if (get_bit_number(tx_selb) == 0) {
+ selb = get_selb_failure_point(start_selb, raw_tx_selb,
+ ggc_get_tuning_cnt_from_buffer(host));
+ tx_selb_inject_policy(host, selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, selb);
+ tx_selb_failed_history_update(host, selb);
+ retuning_flg = TRUE;
+ } else {
+ tx_selb_inject_policy(host, tx_selb);
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ retuning_flg = TRUE;
+ }
+
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host, ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, TRUE);
+ } else {
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ tx_selb_failed_tb_update(host, cur_sela, tx_selb);
+ tx_selb_failed_history_update(host, tx_selb);
+ }
+
+ if (retuning_flg == TRUE) {
+ pr_debug("BHT MSG: %s dll:%xh need retuning\n",
+ __func__, cur_sela);
+ psela_tuning_result[cur_sela] = RETUNING_CASE;
+ } else {
+ pr_debug("BHT MSG: %s dll:%xh pass\n",
+ __func__, cur_sela);
+ psela_tuning_result[cur_sela] = OUTPUT_PASS_TYPE;
+ }
+ } else {
+ psela_tuning_result[cur_sela] = READ_STATUS_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ pr_debug("BHT MSG:== %s dll:%xh read status failed ==\n",
+ __func__, cur_sela);
+ }
+ }
+exit:
+ return ret;
+}
+static int sdhci_bht_sdr104_execute_tuning(struct sdhci_host *host, u32 opcode)
+{
+ struct mmc_host *mmc = host->mmc;
+
+ return sdhci_msm_bayhub_execute_tuning(mmc, opcode);
+}
+
+static int sd_tuning_sw(struct sdhci_host *host)
+{
+ int ret = 0;
+
+ if (is_bus_mode_sdr104(host))
+ ret = sdhci_bht_sdr104_execute_tuning(host, 0x13);
+ else
+ ret = sdhci_bht_sdr50_execute_tuning(host, 0x13);
+
+ return ret;
+}
+
+static bool sd_gg_tuning_status(struct sdhci_host *host,
+ u32 *tx_selb, u32 *all_selb, u64 *raw_tx_selb,
+ bool *status_ret, bool *first_cmd19_status)
+{
+ bool ret = TRUE;
+ int err = sd_tuning_sw(host);
+
+ ret = err == 0 ? TRUE : FALSE;
+ if (err == -ETIMEDOUT) {
+ ret = FALSE;
+ if (first_cmd19_status)
+ *first_cmd19_status = false;
+ goto exit;
+ }
+
+ if (status_ret) {
+ *status_ret =
+ gg_tuning_result(host, tx_selb, all_selb,
+ raw_tx_selb);
+ } else {
+ gg_tuning_result(host, 0, 0, 0);
+ }
+
+exit:
+ return ret;
+}
+
+static bool ggc_sd_tuning(struct sdhci_host *host,
+ bool *first_cmd19_status)
+{
+ bool ret = TRUE;
+ int err = sd_tuning_sw(host);
+
+ ret = err == 0 ? TRUE : FALSE;
+ if (err == -ETIMEDOUT) {
+ ret = FALSE;
+ if (first_cmd19_status)
+ *first_cmd19_status = false;
+ goto exit;
+ }
+
+exit:
+ return ret;
+}
+
+static bool _ggc_output_tuning(struct sdhci_host *host, u8 *selb_pass_win)
+{
+ int cur_sela = 0, dll_sela_cnt = 0;
+ int dll_sela_basis = 0;
+ bool ret = FALSE;
+ u8 win_tb[12] = { 0 };
+ u8 win_mid = 0;
+ u8 win_max = 0;
+ u32 tx_tmp = 0;
+ int target_sela = 0;
+ int target_selb = 0;
+ u32 all_sela, tx_selb, all_selb;
+ u64 raw_tx_selb;
+ bool status_ret = FALSE;
+ int cur_selb = 0;
+ int tuning_error_type[16] = { 0 };
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ struct ggc_platform_t *ggc = &vendor_host->ggc;
+ enum tuning_stat_et *psela_tuning_result = ggc->ggc_sela_tuning_result;
+ int i = 0;
+ u32 idx_r, idx_c;
+ u32 min_pos = 0;
+ u32 all_selb_ar[TUNING_PHASE_SIZE] = { 0 };
+ u32 pass_cnt[TUNING_PHASE_SIZE] = { 0 };
+ u32 cfg = 0;
+ int rescan_selb_cnt = 0;
+ int returning_selb_cnt = 0;
+ bool first_cmd19_sta = TRUE;
+ int next = 0;
+ bool card_status = TRUE;
+ int selb = BIT_PASS_MASK;
+ u8 all_str[TUNING_PHASE_SIZE + 1], tx_str[TUNING_PHASE_SIZE + 1];
+
+ ggc->driver_strength_reinit_flg = 0;
+ vendor_host->ggc.dll_unlock_reinit_flg = 0;
+ dll_sela_basis = get_config_sela_setting(host);
+ cur_selb = get_config_selb_setting(host);
+
+ if (ggc->tuning_cmd7_timeout_reinit_flg) {
+ ggc->tuning_cmd7_timeout_reinit_flg = 0;
+ dll_sela_basis = vendor_host->ggc.ggc_cur_sela;
+ cur_selb = vendor_host->ggc.ggc_sw_selb_tuning_first_selb;
+ pr_debug
+ ("BHT MSG:Tuning start sela: 0x%x, selb: 0x%x where CMD7 timeout\n",
+ dll_sela_basis, cur_selb);
+ }
+
+ for (dll_sela_cnt = 0; dll_sela_cnt < TUNING_PHASE_SIZE; dll_sela_cnt++) {
+ cur_sela =
+ (dll_sela_cnt + dll_sela_basis) % TUNING_PHASE_SIZE;
+ ggc->ggc_cur_sela = cur_sela;
+ pr_debug("BHT MSG: %s select sela dll: %x, selb dll: %x\n",
+ __func__, cur_sela, cur_selb);
+ if (psela_tuning_result[cur_sela] != NO_TUNING) {
+ pr_debug("BHT MSG:sela tuning=%d already tuning,so skip it\n", cur_sela);
+ continue;
+ }
+rescan_selb:
+ host_cmddat_line_reset(host);
+
+ if (dll_sela_cnt == 0) {
+ if (!selx_failure_point_exist
+ (vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) {
+ rescan_selb_cnt = 3;
+ pr_debug("BHT MSG:no need rescan case\n");
+ }
+ status_ret = FALSE;
+ ret = ggc_sd_tuning(host, &first_cmd19_sta);
+
+ if (first_cmd19_sta == FALSE) {
+ _check_bus_mode(host);
+ ggc->cur_bus_mode->dll_voltage_unlock_cnt
+ [ggc->cur_dll_voltage_idx]++;
+ ggc->dll_voltage_scan_map[ggc->cur_dll_voltage_idx] = 1;
+ if (get_next_dll_voltage(ggc->cur_dll_voltage_idx, &next,
+ ggc->cur_bus_mode->dll_voltage_unlock_cnt,
+ ggc->dll_voltage_scan_map) == TRUE)
+ ggc->cur_dll_voltage_idx = next;
+ else
+ ggc->cur_dll_voltage_idx =
+ (ggc->cur_dll_voltage_idx + 1) % 4;
+
+ pr_err("BHT ERR:first cmd19 timeout\n");
+ vendor_host->ggc.dll_unlock_reinit_flg = 1;
+ _ggc_reset_tuning_result_for_dll(host);
+ ret = FALSE;
+ goto exit;
+ }
+ } else if ((is_bus_mode_sdr104(host) == FALSE)
+ && vendor_host->ggc.sdr50_notuning_sela_inject_flag == 1
+ && !GET_IDX_VALUE(vendor_host->ggc.sdr50_notuning_sela_rx_inject,
+ cur_sela)) {
+ pr_debug("BHT MSG:skip %d\n", cur_sela);
+ tuning_error_type[cur_sela] = READ_STATUS_FAIL_TYPE;
+ goto cur_sela_failed;
+ } else {
+ ret = ggc_set_output_tuning_phase_ext(host, &card_status,
+ cur_sela, update_selb(host, cur_selb));
+ if (ret == FALSE || card_status == FALSE) {
+ pr_err
+ ("BHT ERR: output_tuning fail at phase %d,ret=%d,card_status=%d\n",
+ cur_sela, ret, card_status);
+ if (card_status == FALSE) {
+ selb &= ~GENERATE_IDX_VALUE(cur_selb);
+ pr_err("BHT ERR:inject selb %d for update sela/selb fail\n",
+ selb);
+ tx_selb_inject_policy(host, selb);
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host,
+ ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, TRUE);
+
+ if (((11 - get_bit_number(
+ ggc->ggc_cmd_tx_selb_failed_range)) >= 5)) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small\n");
+
+ ggc->driver_strength_reinit_flg =
+ current_ds < 7 ? current_ds + 1 : 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+
+ goto exit;
+ }
+ cur_selb = _ggc_get_suitable_selb_for_next_tuning(host);
+ }
+ psela_tuning_result[cur_sela] = RETUNING_CASE;
+ goto retuning_case;
+ }
+ ret = ggc_sd_tuning(host, NULL);
+ }
+
+ if (ret == FALSE) {
+ pr_err("BHT ERR:Error when output_tuning, fail at phase %d\n",
+ cur_sela);
+ psela_tuning_result[cur_sela] = TUNING_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ continue;
+ }
+
+ ret = _ggc_calc_cur_sela_tuning_result(host, cur_sela, cur_selb);
+
+ if ((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range)) >= 5) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small after result calculate, reinit\n");
+ if (current_ds < 7)
+ ggc->driver_strength_reinit_flg = current_ds + 1;
+ else
+ ggc->driver_strength_reinit_flg = 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+ pr_err("BHT ERR:will change driver strength from %d to %d\n",
+ current_ds,
+ ggc->driver_strength_reinit_flg);
+ goto exit;
+ }
+
+ if (ret == FALSE) {
+ pr_err("BHT ERR:cmd7 timeout fail,reinit\n");
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 1;
+
+ _ggc_update_cur_setting_for_sw_selb_tuning(host,
+ ggc->ggc_cmd_tx_selb_failed_range);
+ ggc_hw_inject_may_recursive(host, ggc->ggc_cmd_tx_selb_failed_range,
+ ggc->ggc_cmd_tx_selb_failed_range, FALSE);
+ if ((11 - get_bit_number(vendor_host->ggc.ggc_cmd_tx_selb_failed_range))
+ >= 5) {
+ u8 current_ds = (u8)(ggc->_gg_reg_cur[15] >> 28);
+
+ pr_err("BHT ERR:pass windows too small, driver strength reinit\n");
+
+ vendor_host->ggc.tuning_cmd7_timeout_reinit_flg = 0;
+
+ ggc->driver_strength_reinit_flg =
+ current_ds < 7 ? current_ds + 1 : 7;
+
+ ggc->_gg_reg_cur[15] &= 0x0F0FFFFF;
+ ggc->_gg_reg_cur[15] |=
+ (ggc->driver_strength_reinit_flg << 28)
+ | (ggc->driver_strength_reinit_flg << 20);
+ ret = FALSE;
+ pr_err("BHT ERR:will change driver strength from %d to %d\n",
+ current_ds,
+ ggc->driver_strength_reinit_flg);
+ goto exit;
+ }
+ goto exit;
+ }
+
+ cur_selb = _ggc_get_suitable_selb_for_next_tuning(host);
+
+ pr_debug("BHT MSG: output sela:%xh pass\n", cur_sela);
+ rescan_selb_cnt++;
+ if ((rescan_selb_cnt < 3) &&
+ (selx_failure_point_exist(vendor_host->ggc.ggc_cmd_tx_selb_failed_range))) {
+ pr_debug("BHT MSG:rescan cnt %d, ggc_cmd_tx_selb_failed_range=0x%x\n",
+ rescan_selb_cnt,
+ vendor_host->ggc.ggc_cmd_tx_selb_failed_range);
+ goto rescan_selb;
+ }
+
+retuning_case:
+ if (psela_tuning_result[cur_sela] == RETUNING_CASE) {
+ returning_selb_cnt++;
+ if (returning_selb_cnt < 3) {
+ rescan_selb_cnt = 0;
+ pr_debug("BHT MSG:retuning %d\n", rescan_selb_cnt);
+ goto rescan_selb;
+ } else {
+ psela_tuning_result[cur_sela] = SET_PHASE_FAIL_TYPE;
+ all_selb_failed_tb_update(host, cur_sela, 0);
+ continue;
+ }
+ }
+
+ goto next_dll_sela;
+
+cur_sela_failed:
+ pr_debug("BHT MSG:read status failedB\n");
+ all_selb = 0;
+ all_selb_failed_tb_update(host, cur_sela, all_selb);
+ pr_debug("BHT MSG: output sela:%xh failed ===\n", cur_sela);
+next_dll_sela:
+ if ((is_bus_mode_sdr104(host) == FALSE)
+ && vendor_host->ggc.sdr50_notuning_crc_error_flag) {
+ u32 fp = 0;
+
+ fp = GENERATE_IDX_VALUE(cur_sela);
+ fp |= GENERATE_IDX_VALUE((cur_sela + 1) % TUNING_PHASE_SIZE);
+ fp |= GENERATE_IDX_VALUE((cur_sela + 10) % TUNING_PHASE_SIZE);
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject &= ~fp;
+ vendor_host->ggc.sdr50_notuning_sela_inject_flag = 1;
+ pr_debug("BHT MSG:sdr50_notuning_sela_rx_inject:%x\n",
+ vendor_host->ggc.sdr50_notuning_sela_rx_inject);
+ ret = FALSE;
+ goto exit;
+ };
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ phase_str(all_str, all_selb_failed_tb_get(host, i));
+ phase_str(tx_str, tx_selb_failed_tb_get(host, i));
+ pr_debug
+ ("BHT MSG:DLL sela[%x] all selb: %s tx selb: %s [%xh,%xh] %s\n",
+ i, all_str, tx_str,
+ all_selb_failed_tb_get(host, i),
+ tx_selb_failed_tb_get(host, i),
+ op_dbg_str[tuning_error_type[i]]);
+
+ }
+
+ /* remove margin passed all selb phase */
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ all_selb_ar[i] = all_selb_failed_tb_get(host, i);
+
+ /* calculate cumulation of diagonal bits */
+ for (idx_c = 0; idx_c < TUNING_PHASE_SIZE; idx_c++) {
+ for (idx_r = 0; idx_r < TUNING_PHASE_SIZE;
+ idx_r++) {
+ pass_cnt[idx_c] += ((all_selb_ar[idx_r] >>
+ ((idx_r + idx_c) % TUNING_PHASE_SIZE)) & 0x01);
+ }
+ if (idx_c == 0)
+ min_pos = 0;
+ else if (pass_cnt[idx_c] < pass_cnt[min_pos])
+ min_pos = idx_c;
+ }
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ all_selb_ar[i] &= ~(1 << (min_pos + i) % TUNING_PHASE_SIZE);
+ all_selb_failed_tb_update(host, i, all_selb_ar[i]);
+ }
+
+ tx_selb = tx_selb_failed_history_get(host);
+
+ pr_debug("inject sw selb & merge tx_selb failed point to all_selb\n");
+ for (i = 0; i < TUNING_PHASE_SIZE; i++)
+ all_selb_failed_tb_update(host, i, tx_selb);
+
+ pr_debug("BHT MSG:inject sw sela failed point to all_selb\n");
+ if (is_bus_mode_sdr104(host))
+ cfg = 0x7ff;
+ else
+ cfg = 0x7ff;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ if (GET_IDX_VALUE(cfg, i) == 0)
+ all_selb_failed_tb_update(host, i, 0);
+ }
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ phase_str(all_str, all_selb_failed_tb_get(host, i));
+ phase_str(tx_str, tx_selb_failed_tb_get(host, i));
+ pr_debug("BHT MSG:DLL sela[%x] all selb: %s tx selb: %s [%xh,%xh] %s\n",
+ i, all_str, tx_str,
+ all_selb_failed_tb_get(host, i),
+ tx_selb_failed_tb_get(host, i),
+ op_dbg_str[tuning_error_type[i]]);
+ }
+
+ tx_selb = tx_selb_failed_history_get(host);
+ tx_selb &= 0x7ff;
+ tx_tmp = tx_selb;
+
+ pr_debug("BHT MSG:---selb merge---\n");
+ if ((tx_selb&0x7ff) == 0x7ff) {
+ if (is_bus_mode_sdr104(host)) {
+ u32 cfg = SDR104_MANUAL_INJECT;
+
+ tx_selb &= cfg;
+ pr_debug("tx selb:%xh SDR104 inject:%xh merge tx_selb:%xh\n",
+ tx_tmp, cfg, tx_selb);
+ } else {
+ u32 cfg = SDR50_MANUAL_INJECT;
+
+ tx_selb &= cfg;
+ pr_debug("tx selb:%xh SDR50 inject:%xh merge tx_selb:%xh\n",
+ tx_tmp, cfg, tx_selb);
+ }
+ }
+
+ if (tx_selb == 0) {
+ pr_err("all failed, force fixed phase sela selb to default\n");
+ target_selb =
+ get_config_selb_setting(host);
+ target_sela =
+ get_config_sela_setting(host);
+ goto final;
+ }
+ phase_str(win_tb, tx_selb);
+ pr_debug("BHT MSG: tx selb[%xh] 11 bit: %s\n",
+ tx_selb, win_tb);
+ bits_generate_array(win_tb, tx_selb);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ target_selb = win_mid;
+
+ all_sela = 0;
+
+ for (i = 0; i < TUNING_PHASE_SIZE; i++) {
+ u32 all_selb = all_selb_failed_tb_get(host, i);
+
+ phase_str(win_tb, all_selb);
+ pr_debug("BHT MSG: all_selb[%xh] 11 bit: %s\n",
+ all_selb, win_tb);
+ bits_generate_array(win_tb, all_selb);
+ chk_phase_window(win_tb, &win_mid,
+ &win_max);
+ *selb_pass_win = win_max;
+ if (all_selb & (1 << target_selb))
+ all_sela |= 1 << i;
+ }
+
+ phase_str(win_tb, all_sela);
+ pr_debug("BHT MSG: all_sela[%xh] 11 bit: %s\n",
+ all_sela, win_tb);
+ bits_generate_array(win_tb, all_sela);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ target_sela = win_mid;
+
+final:
+
+ gg_fix_output_tuning_phase(host, target_sela,
+ target_selb);
+
+ ret = sd_gg_tuning_status(host, &tx_selb,
+ &all_selb, &raw_tx_selb, &status_ret, NULL);
+ if (ret == FALSE) {
+ pr_err("Error when output_tuning, sd_tuning fail\n");
+ ret = FALSE;
+ goto exit;
+ }
+
+ /* use final pass windows */
+ phase_str(win_tb, all_selb);
+ pr_debug("BHT MSG: all_selb[%xh] 11 bit: %s\n",
+ all_selb, win_tb);
+ bits_generate_array(win_tb, all_selb);
+ chk_phase_window(win_tb, &win_mid, &win_max);
+ *selb_pass_win = win_max;
+
+ vendor_host->ggc.selx_tuning_done_flag = 1;
+
+exit:
+ pr_debug("BHT MSG:exit:%s %d\n", __func__, ret);
+ return ret;
+}
+
+static int sdhci_bht_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *vendor_host = sdhci_pltfm_priv(pltfm_host);
+ u8 tw = 0;
+ int ret = 0;
+
+ if (vendor_host->ggc.bh201_used) {
+ pr_debug("BHT MSG:enter bht tuning\n");
+ if (host->clock < CORE_FREQ_100MHZ) {
+ pr_debug("BHT MSG:%d less 100Mhz,no tuning\n", host->clock);
+ return 0;
+ }
+
+ if (vendor_host->ggc.tuning_in_progress) {
+ pr_debug("BHT MSG:tuning_in_progress\n");
+ return 0;
+ }
+ vendor_host->ggc.tuning_in_progress = true;
+
+ if (vendor_host->ggc.selx_tuning_done_flag) {
+ pr_debug("BHT MSG:GGC tuning is done, just do vendor host tuning");
+ if (is_bus_mode_sdr104(host))
+ ret = sdhci_bht_sdr104_execute_tuning(host, 0x13);
+ else
+ ret = sdhci_bht_sdr50_execute_tuning(host, 0x13);
+ } else {
+ ret = !_ggc_output_tuning(host, &tw);
+ }
+ vendor_host->ggc.tuning_in_progress = false;
+ return ret;
+ } else
+ return sdhci_msm_bayhub_execute_tuning(vendor_host->mmc, opcode);
+}
+
+/*
+ * sdhci_msm_bayhub_hs400 - Calibrate the DLL for HS400 bus speed mode operation.
+ * This needs to be done for both tuning and enhanced_strobe mode.
+ * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz
+ * fixed feedback clock is used.
+ */
+static void sdhci_msm_bayhub_hs400(struct sdhci_host *host, struct mmc_ios *ios)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ if (host->clock > CORE_FREQ_100MHZ &&
+ (msm_bayhub_host->tuning_done || ios->enhanced_strobe) &&
+ !msm_bayhub_host->calibration_done) {
+ ret = sdhci_msm_bayhub_hs400_dll_calibration(host);
+ if (!ret)
+ msm_bayhub_host->calibration_done = true;
+ else
+ pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n",
+ mmc_hostname(host->mmc), ret);
+ }
+}
+
+static void sdhci_msm_bayhub_set_uhs_signaling(struct sdhci_host *host,
+ unsigned int uhs)
+{
+ struct mmc_host *mmc = host->mmc;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u16 ctrl_2;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ /* Select Bus Speed Mode for host */
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ switch (uhs) {
+ case MMC_TIMING_UHS_SDR12:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
+ break;
+ case MMC_TIMING_UHS_SDR25:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
+ break;
+ case MMC_TIMING_UHS_SDR50:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
+ break;
+ case MMC_TIMING_MMC_HS400:
+ case MMC_TIMING_MMC_HS200:
+ case MMC_TIMING_UHS_SDR104:
+ ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
+ break;
+ case MMC_TIMING_UHS_DDR50:
+ case MMC_TIMING_MMC_DDR52:
+ ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
+ break;
+ }
+
+ /*
+ * When clock frequency is less than 100MHz, the feedback clock must be
+ * provided and DLL must not be used so that tuning can be skipped. To
+ * provide feedback clock, the mode selection can be any value less
+ * than 3'b011 in bits [2:0] of HOST CONTROL2 register.
+ */
+ if (host->clock <= CORE_FREQ_100MHZ) {
+ if (uhs == MMC_TIMING_MMC_HS400 ||
+ uhs == MMC_TIMING_MMC_HS200 ||
+ uhs == MMC_TIMING_UHS_SDR104)
+ ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
+ /*
+ * DLL is not required for clock <= 100MHz
+ * Thus, make sure DLL it is disabled when not required
+ */
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_RST;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+ config |= CORE_DLL_PDN;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_dll_config);
+
+ /*
+ * The DLL needs to be restored and CDCLP533 recalibrated
+ * when the clock frequency is set back to 400MHz.
+ */
+ msm_bayhub_host->calibration_done = false;
+ }
+
+ dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
+ mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
+ sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
+
+ if (mmc->ios.timing == MMC_TIMING_MMC_HS400)
+ sdhci_msm_bayhub_hs400(host, &mmc->ios);
+}
+
+static int sdhci_msm_bayhub_set_pincfg(struct sdhci_msm_bayhub_host *msm_bayhub_host, bool level)
+{
+ struct platform_device *pdev = msm_bayhub_host->pdev;
+ int ret;
+
+ if (level)
+ ret = pinctrl_pm_select_default_state(&pdev->dev);
+ else
+ ret = pinctrl_pm_select_sleep_state(&pdev->dev);
+
+ return ret;
+}
+
+static int sdhci_msm_bayhub_set_vmmc(struct mmc_host *mmc)
+{
+ if (IS_ERR(mmc->supply.vmmc))
+ return 0;
+
+ return mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, mmc->ios.vdd);
+}
+
+static int msm_bayhub_toggle_vqmmc(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool level)
+{
+ int ret;
+ struct mmc_ios ios;
+
+ if (msm_bayhub_host->vqmmc_enabled == level)
+ return 0;
+
+ if (level) {
+ /* Set the IO voltage regulator to default voltage level */
+ if (msm_bayhub_host->caps_0 & CORE_3_0V_SUPPORT)
+ ios.signal_voltage = MMC_SIGNAL_VOLTAGE_330;
+ else if (msm_bayhub_host->caps_0 & CORE_1_8V_SUPPORT)
+ ios.signal_voltage = MMC_SIGNAL_VOLTAGE_180;
+
+ if (msm_bayhub_host->caps_0 & CORE_VOLT_SUPPORT) {
+ ret = mmc_regulator_set_vqmmc(mmc, &ios);
+ if (ret < 0) {
+ dev_err(mmc_dev(mmc), "%s: vqmmc set volgate failed: %d\n",
+ mmc_hostname(mmc), ret);
+ goto out;
+ }
+ }
+ ret = regulator_enable(mmc->supply.vqmmc);
+ } else {
+ ret = regulator_disable(mmc->supply.vqmmc);
+ }
+
+ if (ret)
+ dev_err(mmc_dev(mmc), "%s: vqmm %sable failed: %d\n",
+ mmc_hostname(mmc), level ? "en":"dis", ret);
+ else
+ msm_bayhub_host->vqmmc_enabled = level;
+out:
+ return ret;
+}
+
+static int msm_bayhub_config_vqmmc_mode(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool hpm)
+{
+ int load, ret;
+
+ load = hpm ? MMC_VQMMC_MAX_LOAD_UA : 0;
+ ret = regulator_set_load(mmc->supply.vqmmc, load);
+ if (ret)
+ dev_err(mmc_dev(mmc), "%s: vqmmc set load failed: %d\n",
+ mmc_hostname(mmc), ret);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_set_vqmmc(struct sdhci_msm_bayhub_host *msm_bayhub_host,
+ struct mmc_host *mmc, bool level)
+{
+ int ret;
+ bool always_on;
+
+ if (IS_ERR(mmc->supply.vqmmc) ||
+ (mmc->ios.power_mode == MMC_POWER_UNDEFINED))
+ return 0;
+ /*
+ * For eMMC don't turn off Vqmmc, Instead just configure it in LPM
+ * and HPM modes by setting the corresponding load.
+ *
+ * Till eMMC is initialized (i.e. always_on == 0), just turn on/off
+ * Vqmmc. Vqmmc gets turned off only if init fails and mmc_power_off
+ * gets invoked. Once eMMC is initialized (i.e. always_on == 1),
+ * Vqmmc should remain ON, So just set the load instead of turning it
+ * off/on.
+ */
+ always_on = !mmc_card_is_removable(mmc) &&
+ mmc->card && mmc_card_mmc(mmc->card);
+
+ if (always_on)
+ ret = msm_bayhub_config_vqmmc_mode(msm_bayhub_host, mmc, level);
+ else
+ ret = msm_bayhub_toggle_vqmmc(msm_bayhub_host, mmc, level);
+
+ return ret;
+}
+
+static inline void sdhci_msm_bayhub_init_pwr_irq_wait(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ init_waitqueue_head(&msm_bayhub_host->pwr_irq_wait);
+}
+
+static inline void sdhci_msm_bayhub_complete_pwr_irq_wait(
+ struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ wake_up(&msm_bayhub_host->pwr_irq_wait);
+}
+
+/*
+ * sdhci_msm_bayhub_check_power_status API should be called when registers writes
+ * which can toggle sdhci IO bus ON/OFF or change IO lines HIGH/LOW happens.
+ * To what state the register writes will change the IO lines should be passed
+ * as the argument req_type. This API will check whether the IO line's state
+ * is already the expected state and will wait for power irq only if
+ * power irq is expected to be triggered based on the current IO line state
+ * and expected IO line state.
+ */
+static void sdhci_msm_bayhub_check_power_status(struct sdhci_host *host, u32 req_type)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ bool done = false;
+ u32 val = SWITCHABLE_SIGNALING_VOLTAGE;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n",
+ mmc_hostname(host->mmc), __func__, req_type,
+ msm_bayhub_host->curr_pwr_state, msm_bayhub_host->curr_io_level);
+
+ /*
+ * The power interrupt will not be generated for signal voltage
+ * switches if SWITCHABLE_SIGNALING_VOLTAGE in MCI_GENERICS is not set.
+ * Since sdhci-msm_bayhub-v5, this bit has been removed and SW must consider
+ * it as always set.
+ */
+ if (!msm_bayhub_host->mci_removed)
+ val = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_generics);
+ if ((req_type & REQ_IO_HIGH || req_type & REQ_IO_LOW) &&
+ !(val & SWITCHABLE_SIGNALING_VOLTAGE)) {
+ return;
+ }
+
+ /*
+ * The IRQ for request type IO High/LOW will be generated when -
+ * there is a state change in 1.8V enable bit (bit 3) of
+ * SDHCI_HOST_CONTROL2 register. The reset state of that bit is 0
+ * which indicates 3.3V IO voltage. So, when MMC core layer tries
+ * to set it to 3.3V before card detection happens, the
+ * IRQ doesn't get triggered as there is no state change in this bit.
+ * The driver already handles this case by changing the IO voltage
+ * level to high as part of controller power up sequence. Hence, check
+ * for host->pwr to handle a case where IO voltage high request is
+ * issued even before controller power up.
+ */
+ if ((req_type & REQ_IO_HIGH) && !host->pwr) {
+ pr_debug("%s: do not wait for power IRQ that never comes, req_type: %d\n",
+ mmc_hostname(host->mmc), req_type);
+ return;
+ }
+ if ((req_type & msm_bayhub_host->curr_pwr_state) ||
+ (req_type & msm_bayhub_host->curr_io_level))
+ done = true;
+ /*
+ * This is needed here to handle cases where register writes will
+ * not change the current bus state or io level of the controller.
+ * In this case, no power irq will be triggerred and we should
+ * not wait.
+ */
+ if (!done) {
+ if (!wait_event_timeout(msm_bayhub_host->pwr_irq_wait,
+ msm_bayhub_host->pwr_irq_flag,
+ msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS)))
+ dev_warn(&msm_bayhub_host->pdev->dev,
+ "%s: pwr_irq for req: (%d) timed out\n",
+ mmc_hostname(host->mmc), req_type);
+ }
+ pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc),
+ __func__, req_type);
+}
+
+static void sdhci_msm_bayhub_dump_pwr_ctrl_regs(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset =
+ msm_bayhub_host->offset;
+
+ pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x\n",
+ mmc_hostname(host->mmc),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_status),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_mask),
+ msm_bayhub_host_readl(msm_bayhub_host, host, msm_bayhub_offset->core_pwrctl_ctl));
+}
+
+static void sdhci_msm_bayhub_handle_pwr_irq(struct sdhci_host *host, int irq)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct mmc_host *mmc = host->mmc;
+ u32 irq_status, irq_ack = 0;
+ int retry = 10, ret;
+ u32 pwr_state = 0, io_level = 0;
+ u32 config;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ irq_status = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_pwrctl_status);
+ irq_status &= INT_MASK;
+
+ msm_bayhub_host_writel(msm_bayhub_host, irq_status, host,
+ msm_bayhub_offset->core_pwrctl_clear);
+
+ /*
+ * There is a rare HW scenario where the first clear pulse could be
+ * lost when actual reset and clear/read of status register is
+ * happening at a time. Hence, retry for at least 10 times to make
+ * sure status register is cleared. Otherwise, this will result in
+ * a spurious power IRQ resulting in system instability.
+ */
+ while (irq_status & msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_pwrctl_status)) {
+ if (retry == 0) {
+ pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n",
+ mmc_hostname(host->mmc), irq_status);
+ sdhci_msm_bayhub_dump_pwr_ctrl_regs(host);
+ WARN_ON(1);
+ break;
+ }
+ msm_bayhub_host_writel(msm_bayhub_host, irq_status, host,
+ msm_bayhub_offset->core_pwrctl_clear);
+ retry--;
+ udelay(10);
+ }
+
+ /* Handle BUS ON/OFF*/
+ if (irq_status & CORE_PWRCTL_BUS_ON) {
+ if (msm_bayhub_host->ggc.bh201_used)
+ bh201_signal_voltage_on_off(host, 1);
+ pwr_state = REQ_BUS_ON;
+ io_level = REQ_IO_HIGH;
+ }
+ if (irq_status & CORE_PWRCTL_BUS_OFF) {
+ if (msm_bayhub_host->ggc.bh201_used)
+ bh201_signal_voltage_on_off(host, 0);
+ pwr_state = REQ_BUS_OFF;
+ io_level = REQ_IO_LOW;
+ }
+
+ if (pwr_state) {
+ ret = sdhci_msm_bayhub_set_vmmc(mmc);
+ if (!ret)
+ ret = sdhci_msm_bayhub_set_vqmmc(msm_bayhub_host, mmc,
+ pwr_state & REQ_BUS_ON);
+ if (!ret)
+ ret = sdhci_msm_bayhub_set_pincfg(msm_bayhub_host,
+ pwr_state & REQ_BUS_ON);
+ if (!ret)
+ irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
+ else
+ irq_ack |= CORE_PWRCTL_BUS_FAIL;
+ }
+
+ /* Handle IO LOW/HIGH */
+ if (irq_status & CORE_PWRCTL_IO_LOW)
+ io_level = REQ_IO_LOW;
+
+ if (irq_status & CORE_PWRCTL_IO_HIGH)
+ io_level = REQ_IO_HIGH;
+
+ if (io_level)
+ irq_ack |= CORE_PWRCTL_IO_SUCCESS;
+
+ if (io_level && !IS_ERR(mmc->supply.vqmmc) && !pwr_state) {
+ ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios);
+ if (ret < 0) {
+ dev_err(mmc_dev(mmc), "%s: IO_level setting failed(%d). signal_voltage: %d, vdd: %d irq_status: 0x%08x\n",
+ mmc_hostname(mmc), ret,
+ mmc->ios.signal_voltage, mmc->ios.vdd,
+ irq_status);
+ irq_ack |= CORE_PWRCTL_IO_FAIL;
+ }
+ }
+
+ /*
+ * The driver has to acknowledge the interrupt, switch voltages and
+ * report back if it succeeded or not to this register. The voltage
+ * switches are handled by the sdhci core, so just report success.
+ */
+ msm_bayhub_host_writel(msm_bayhub_host, irq_ack, host,
+ msm_bayhub_offset->core_pwrctl_ctl);
+
+ /*
+ * If we don't have info regarding the voltage levels supported by
+ * regulators, don't change the IO PAD PWR SWITCH.
+ */
+ if (msm_bayhub_host->caps_0 & CORE_VOLT_SUPPORT) {
+ u32 new_config;
+ /*
+ * We should unset IO PAD PWR switch only if the register write
+ * can set IO lines high and the regulator also switches to 3 V.
+ * Else, we should keep the IO PAD PWR switch set.
+ * This is applicable to certain targets where eMMC vccq supply
+ * is only 1.8V. In such targets, even during REQ_IO_HIGH, the
+ * IO PAD PWR switch must be kept set to reflect actual
+ * regulator voltage. This way, during initialization of
+ * controllers with only 1.8V, we will set the IO PAD bit
+ * without waiting for a REQ_IO_LOW.
+ */
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ new_config = config;
+
+ if ((io_level & REQ_IO_HIGH) &&
+ (msm_bayhub_host->caps_0 & CORE_3_0V_SUPPORT))
+ new_config &= ~CORE_IO_PAD_PWR_SWITCH;
+ else if ((io_level & REQ_IO_LOW) ||
+ (msm_bayhub_host->caps_0 & CORE_1_8V_SUPPORT))
+ new_config |= CORE_IO_PAD_PWR_SWITCH;
+
+ if (config ^ new_config)
+ writel_relaxed(new_config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ }
+
+ if (pwr_state)
+ msm_bayhub_host->curr_pwr_state = pwr_state;
+ if (io_level)
+ msm_bayhub_host->curr_io_level = io_level;
+
+ dev_dbg(mmc_dev(mmc), "%s: %s: Handled IRQ(%d), irq_status=0x%x, ack=0x%x\n",
+ mmc_hostname(msm_bayhub_host->mmc), __func__, irq, irq_status,
+ irq_ack);
+}
+
+static irqreturn_t sdhci_msm_bayhub_pwr_irq(int irq, void *data)
+{
+ struct sdhci_host *host = (struct sdhci_host *)data;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ sdhci_msm_bayhub_handle_pwr_irq(host, irq);
+ msm_bayhub_host->pwr_irq_flag = 1;
+ sdhci_msm_bayhub_complete_pwr_irq_wait(msm_bayhub_host);
+
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int sdhci_msm_bayhub_get_max_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct clk *core_clk = msm_bayhub_host->bulk_clks[0].clk;
+
+ return clk_round_rate(core_clk, ULONG_MAX);
+}
+
+static unsigned int sdhci_msm_bayhub_get_min_clock(struct sdhci_host *host)
+{
+ return SDHCI_MSM_MIN_CLOCK;
+}
+
+/**
+ * __sdhci_msm_bayhub_set_clock - sdhci_msm_bayhub clock control.
+ *
+ * Description:
+ * MSM controller does not use internal divider and
+ * instead directly control the GCC clock as per
+ * HW recommendation.
+ **/
+static void __sdhci_msm_bayhub_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ u16 clk;
+
+ sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
+
+ if (clock == 0)
+ return;
+
+ /*
+ * MSM controller do not use clock divider.
+ * Thus read SDHCI_CLOCK_CONTROL and only enable
+ * clock with no divider value programmed.
+ */
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ sdhci_enable_clk(host, clk);
+}
+
+/* sdhci_msm_bayhub_set_clock - Called with (host->lock) spinlock held. */
+static void sdhci_msm_bayhub_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (!clock) {
+ host->mmc->actual_clock = msm_bayhub_host->clk_rate = 0;
+ goto out;
+ }
+
+ sdhci_msm_bayhub_hc_select_mode(host);
+
+ msm_bayhub_set_clock_rate_for_bus_mode(host, clock);
+out:
+ __sdhci_msm_bayhub_set_clock(host, clock);
+}
+
+/*****************************************************************************\
+ * *
+ * MSM Command Queue Engine (CQE) *
+ * *
+\*****************************************************************************/
+
+static u32 sdhci_msm_bayhub_cqe_irq(struct sdhci_host *host, u32 intmask)
+{
+ int cmd_error = 0;
+ int data_error = 0;
+
+ if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
+ return intmask;
+
+ cqhci_irq(host->mmc, intmask, cmd_error, data_error);
+ return 0;
+}
+
+static void sdhci_msm_bayhub_cqe_disable(struct mmc_host *mmc, bool recovery)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ unsigned long flags;
+ u32 ctrl;
+
+ /*
+ * When CQE is halted, the legacy SDHCI path operates only
+ * on 16-byte descriptors in 64bit mode.
+ */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ host->desc_sz = 16;
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ /*
+ * During CQE command transfers, command complete bit gets latched.
+ * So s/w should clear command complete interrupt status when CQE is
+ * either halted or disabled. Otherwise unexpected SDCHI legacy
+ * interrupt gets triggered when CQE is halted/disabled.
+ */
+ ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
+ ctrl |= SDHCI_INT_RESPONSE;
+ sdhci_writel(host, ctrl, SDHCI_INT_ENABLE);
+ sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ sdhci_cqe_disable(mmc, recovery);
+}
+
+static const struct cqhci_host_ops sdhci_msm_bayhub_cqhci_ops = {
+ .enable = sdhci_cqe_enable,
+ .disable = sdhci_msm_bayhub_cqe_disable,
+};
+
+static int sdhci_msm_bayhub_cqe_add_host(struct sdhci_host *host,
+ struct platform_device *pdev)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ struct cqhci_host *cq_host;
+ bool dma64;
+ u32 cqcfg;
+ int ret;
+
+ /*
+ * When CQE is halted, SDHC operates only on 16byte ADMA descriptors.
+ * So ensure ADMA table is allocated for 16byte descriptors.
+ */
+ if (host->caps & SDHCI_CAN_64BIT)
+ host->alloc_desc_sz = 16;
+
+ ret = sdhci_setup_host(host);
+ if (ret)
+ return ret;
+
+ cq_host = cqhci_pltfm_init(pdev);
+ if (IS_ERR(cq_host)) {
+ ret = PTR_ERR(cq_host);
+ dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
+ goto cleanup;
+ }
+
+ msm_bayhub_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
+ cq_host->ops = &sdhci_msm_bayhub_cqhci_ops;
+
+ dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
+
+ ret = cqhci_init(cq_host, host->mmc, dma64);
+ if (ret) {
+ dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
+ mmc_hostname(host->mmc), ret);
+ goto cleanup;
+ }
+
+ /* Disable cqe reset due to cqe enable signal */
+ cqcfg = cqhci_readl(cq_host, CQHCI_VENDOR_CFG1);
+ cqcfg |= CQHCI_VENDOR_DIS_RST_ON_CQ_EN;
+ cqhci_writel(cq_host, cqcfg, CQHCI_VENDOR_CFG1);
+
+ /*
+ * SDHC expects 12byte ADMA descriptors till CQE is enabled.
+ * So limit desc_sz to 12 so that the data commands that are sent
+ * during card initialization (before CQE gets enabled) would
+ * get executed without any issues.
+ */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ host->desc_sz = 12;
+
+ ret = __sdhci_add_host(host);
+ if (ret)
+ goto cleanup;
+
+ dev_info(&pdev->dev, "%s: CQE init: success\n",
+ mmc_hostname(host->mmc));
+ return ret;
+
+cleanup:
+ sdhci_cleanup_host(host);
+ return ret;
+}
+
+/*
+ * Platform specific register write functions. This is so that, if any
+ * register write needs to be followed up by platform specific actions,
+ * they can be added here. These functions can go to sleep when writes
+ * to certain registers are done.
+ * These functions are relying on sdhci_set_ios not using spinlock.
+ */
+static int __sdhci_msm_bayhub_check_write(struct sdhci_host *host, u16 val, int reg)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ u32 req_type = 0;
+
+ switch (reg) {
+ case SDHCI_HOST_CONTROL2:
+ req_type = (val & SDHCI_CTRL_VDD_180) ? REQ_IO_LOW :
+ REQ_IO_HIGH;
+ break;
+ case SDHCI_SOFTWARE_RESET:
+ if (host->pwr && (val & SDHCI_RESET_ALL))
+ req_type = REQ_BUS_OFF;
+ break;
+ case SDHCI_POWER_CONTROL:
+ req_type = !val ? REQ_BUS_OFF : REQ_BUS_ON;
+ break;
+ case SDHCI_TRANSFER_MODE:
+ msm_bayhub_host->transfer_mode = val;
+ break;
+ case SDHCI_COMMAND:
+ if (!msm_bayhub_host->use_cdr)
+ break;
+ if ((msm_bayhub_host->transfer_mode & SDHCI_TRNS_READ) &&
+ SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK_HS200 &&
+ SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK)
+ sdhci_msm_bayhub_set_cdr(host, true);
+ else
+ sdhci_msm_bayhub_set_cdr(host, false);
+ break;
+ }
+
+ if (req_type) {
+ msm_bayhub_host->pwr_irq_flag = 0;
+ /*
+ * Since this register write may trigger a power irq, ensure
+ * all previous register writes are complete by this point.
+ */
+ mb();
+ }
+ return req_type;
+}
+
+/* This function may sleep*/
+static void sdhci_msm_bayhub_writew(struct sdhci_host *host, u16 val, int reg)
+{
+ u32 req_type = 0;
+
+ req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
+ writew_relaxed(val, host->ioaddr + reg);
+
+ if (req_type)
+ sdhci_msm_bayhub_check_power_status(host, req_type);
+}
+
+/* This function may sleep*/
+static void sdhci_msm_bayhub_writeb(struct sdhci_host *host, u8 val, int reg)
+{
+ u32 req_type = 0;
+
+ req_type = __sdhci_msm_bayhub_check_write(host, val, reg);
+
+ writeb_relaxed(val, host->ioaddr + reg);
+
+ if (req_type)
+ sdhci_msm_bayhub_check_power_status(host, req_type);
+}
+
+static void sdhci_msm_bayhub_set_regulator_caps(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ struct mmc_host *mmc = msm_bayhub_host->mmc;
+ struct regulator *supply = mmc->supply.vqmmc;
+ u32 caps = 0, config;
+ struct sdhci_host *host = mmc_priv(mmc);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ if (regulator_is_supported_voltage(supply, 1700000, 1950000))
+ caps |= CORE_1_8V_SUPPORT;
+ if (regulator_is_supported_voltage(supply, 2700000, 3600000))
+ caps |= CORE_3_0V_SUPPORT;
+
+ if (!caps)
+ pr_warn("%s: 1.8/3V not supported for vqmmc\n",
+ mmc_hostname(mmc));
+ }
+
+ if (caps) {
+ /*
+ * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH
+ * bit can be used as required later on.
+ */
+ u32 io_level = msm_bayhub_host->curr_io_level;
+
+ config = readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec);
+ config |= CORE_IO_PAD_PWR_SWITCH_EN;
+
+ if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT))
+ config &= ~CORE_IO_PAD_PWR_SWITCH;
+ else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT))
+ config |= CORE_IO_PAD_PWR_SWITCH;
+
+ writel_relaxed(config,
+ host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+ }
+ msm_bayhub_host->caps_0 |= caps;
+ pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
+}
+
+static void sdhci_msm_bayhub_reset(struct sdhci_host *host, u8 mask)
+{
+ if ((host->mmc->caps2 & MMC_CAP2_CQE) && (mask & SDHCI_RESET_ALL))
+ cqhci_deactivate(host->mmc);
+ sdhci_reset(host, mask);
+}
+
+static int sdhci_msm_bayhub_register_vreg(struct sdhci_msm_bayhub_host *msm_bayhub_host)
+{
+ int ret;
+
+ ret = mmc_regulator_get_supply(msm_bayhub_host->mmc);
+ if (ret)
+ return ret;
+
+ sdhci_msm_bayhub_set_regulator_caps(msm_bayhub_host);
+
+ return 0;
+}
+
+static int sdhci_msm_bayhub_start_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ u16 ctrl, status;
+
+ /*
+ * Signal Voltage Switching is only applicable for Host Controllers
+ * v3.00 and above.
+ */
+ if (host->version < SDHCI_SPEC_300)
+ return 0;
+
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ switch (ios->signal_voltage) {
+ case MMC_SIGNAL_VOLTAGE_330:
+ if (!(host->flags & SDHCI_SIGNALING_330))
+ return -EINVAL;
+
+ /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+ ctrl &= ~SDHCI_CTRL_VDD_180;
+ break;
+ case MMC_SIGNAL_VOLTAGE_180:
+ if (!(host->flags & SDHCI_SIGNALING_180))
+ return -EINVAL;
+
+ /* Enable 1.8V Signal Enable in the Host Control2 register */
+ ctrl |= SDHCI_CTRL_VDD_180;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
+
+ /* regulator output should be stable within 5 ms */
+ status = ctrl & SDHCI_CTRL_VDD_180;
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if ((ctrl & SDHCI_CTRL_VDD_180) == status)
+ return 0;
+
+ dev_warn(mmc_dev(mmc), "%s: Regulator output did not became stable\n",
+ mmc_hostname(mmc));
+
+ return -EAGAIN;
+}
+
+#define DRIVER_NAME "sdhci_msm_bayhub"
+#define SDHCI_MSM_DUMP(f, x...) \
+ pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
+
+static void sdhci_msm_bayhub_dump_vendor_regs(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset = msm_bayhub_host->offset;
+
+ SDHCI_MSM_DUMP("----------- VENDOR REGISTER DUMP -----------\n");
+
+ SDHCI_MSM_DUMP(
+ "DLL sts: 0x%08x | DLL cfg: 0x%08x | DLL cfg2: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_status),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_2));
+ SDHCI_MSM_DUMP(
+ "DLL cfg3: 0x%08x | DLL usr ctl: 0x%08x | DDR cfg: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_config_3),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_dll_usr_ctl),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_ddr_config));
+ SDHCI_MSM_DUMP(
+ "Vndr func: 0x%08x | Vndr func2 : 0x%08x Vndr func3: 0x%08x\n",
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec),
+ readl_relaxed(host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec_func2),
+ readl_relaxed(host->ioaddr + msm_bayhub_offset->core_vendor_spec3));
+}
+
+static const struct sdhci_msm_bayhub_variant_ops mci_var_ops = {
+ .msm_bayhub_readl_relaxed = sdhci_msm_bayhub_mci_variant_readl_relaxed,
+ .msm_bayhub_writel_relaxed = sdhci_msm_bayhub_mci_variant_writel_relaxed,
+};
+
+static const struct sdhci_msm_bayhub_variant_ops v5_var_ops = {
+ .msm_bayhub_readl_relaxed = sdhci_msm_bayhub_v5_variant_readl_relaxed,
+ .msm_bayhub_writel_relaxed = sdhci_msm_bayhub_v5_variant_writel_relaxed,
+};
+
+static const struct sdhci_msm_bayhub_variant_info sdhci_msm_bayhub_v5_var = {
+ .mci_removed = true,
+ .var_ops = &v5_var_ops,
+ .offset = &sdhci_msm_bayhub_v5_offset,
+};
+
+static const struct sdhci_msm_bayhub_variant_info sdm845_sdhci_var = {
+ .mci_removed = true,
+ .restore_dll_config = true,
+ .var_ops = &v5_var_ops,
+ .offset = &sdhci_msm_bayhub_v5_offset,
+};
+
+static const struct of_device_id sdhci_msm_bayhub_dt_match[] = {
+ {.compatible = "qcom,sdhci-msm-bayhub-v5", .data = &sdhci_msm_bayhub_v5_var},
+ {.compatible = "qcom,sdm845-bayhub-sdhci", .data = &sdm845_sdhci_var},
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, sdhci_msm_bayhub_dt_match);
+
+static const struct sdhci_ops sdhci_msm_bayhub_ops = {
+ .reset = sdhci_msm_bayhub_reset,
+ .set_clock = sdhci_msm_bayhub_set_clock,
+ .get_min_clock = sdhci_msm_bayhub_get_min_clock,
+ .get_max_clock = sdhci_msm_bayhub_get_max_clock,
+ .set_bus_width = sdhci_set_bus_width,
+ .set_uhs_signaling = sdhci_msm_bayhub_set_uhs_signaling,
+ .write_w = sdhci_msm_bayhub_writew,
+ .write_b = sdhci_msm_bayhub_writeb,
+ .irq = sdhci_msm_bayhub_cqe_irq,
+ .dump_vendor_regs = sdhci_msm_bayhub_dump_vendor_regs,
+ .set_power = sdhci_set_power_noreg,
+};
+
+static const struct sdhci_pltfm_data sdhci_msm_bayhub_pdata = {
+ .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+ SDHCI_QUIRK_SINGLE_POWER_WRITE |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12,
+
+ .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
+ .ops = &sdhci_msm_bayhub_ops,
+};
+
+static inline void sdhci_msm_bayhub_get_of_property(struct platform_device *pdev,
+ struct sdhci_host *host)
+{
+ struct device_node *node = pdev->dev.of_node;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (of_property_read_u32(node, "qcom,ddr-config",
+ &msm_bayhub_host->ddr_config))
+ msm_bayhub_host->ddr_config = DDR_CONFIG_POR_VAL;
+
+ of_property_read_u32(node, "qcom,dll-config", &msm_bayhub_host->dll_config);
+}
+
+static int sdhci_msm_bayhub_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_msm_bayhub_host *msm_bayhub_host;
+ struct resource *core_memres;
+ struct clk *clk;
+ int ret;
+ u16 host_version, core_minor;
+ u32 core_version, config;
+ u8 core_major;
+ const struct sdhci_msm_bayhub_offset *msm_bayhub_offset;
+ const struct sdhci_msm_bayhub_variant_info *var_info;
+ struct device_node *node = pdev->dev.of_node;
+
+ host = sdhci_pltfm_init(pdev, &sdhci_msm_bayhub_pdata, sizeof(*msm_bayhub_host));
+ if (IS_ERR(host))
+ return PTR_ERR(host);
+
+ host->sdma_boundary = 0;
+ pltfm_host = sdhci_priv(host);
+ msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ msm_bayhub_host->mmc = host->mmc;
+ msm_bayhub_host->pdev = pdev;
+
+ ret = mmc_of_parse(host->mmc);
+ if (ret)
+ goto pltfm_free;
+
+ if (of_find_property(node, "use-bayhub-bh201", NULL)) {
+ sdhci_bh201_parse(msm_bayhub_host->mmc);
+ INIT_DELAYED_WORK(&host->mmc->detect, mmc_rescan_bayhub);
+ } else
+ msm_bayhub_host->ggc.bh201_used = 0;
+
+ /*
+ * Based on the compatible string, load the required msm_bayhub host info from
+ * the data associated with the version info.
+ */
+ var_info = of_device_get_match_data(&pdev->dev);
+
+ msm_bayhub_host->mci_removed = var_info->mci_removed;
+ msm_bayhub_host->restore_dll_config = var_info->restore_dll_config;
+ msm_bayhub_host->var_ops = var_info->var_ops;
+ msm_bayhub_host->offset = var_info->offset;
+ msm_bayhub_host->uses_tassadar_dll = var_info->uses_tassadar_dll;
+
+ msm_bayhub_offset = msm_bayhub_host->offset;
+
+ sdhci_get_of_property(pdev);
+ sdhci_msm_bayhub_get_of_property(pdev, host);
+
+ msm_bayhub_host->saved_tuning_phase = INVALID_TUNING_PHASE;
+
+ /* Setup SDCC bus voter clock. */
+ msm_bayhub_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
+ if (!IS_ERR(msm_bayhub_host->bus_clk)) {
+ /* Vote for max. clk rate for max. performance */
+ ret = clk_set_rate(msm_bayhub_host->bus_clk, INT_MAX);
+ if (ret)
+ goto pltfm_free;
+ ret = clk_prepare_enable(msm_bayhub_host->bus_clk);
+ if (ret)
+ goto pltfm_free;
+ }
+
+ /* Setup main peripheral bus clock */
+ clk = devm_clk_get(&pdev->dev, "iface");
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
+ dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret);
+ goto bus_clk_disable;
+ }
+ msm_bayhub_host->bulk_clks[1].clk = clk;
+
+ /* Setup SDC MMC clock */
+ clk = devm_clk_get(&pdev->dev, "core");
+ if (IS_ERR(clk)) {
+ ret = PTR_ERR(clk);
+ dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret);
+ goto bus_clk_disable;
+ }
+ msm_bayhub_host->bulk_clks[0].clk = clk;
+
+ /* Check for optional interconnect paths */
+ ret = dev_pm_opp_of_find_icc_paths(&pdev->dev, NULL);
+ if (ret)
+ goto bus_clk_disable;
+
+ msm_bayhub_host->opp_table = dev_pm_opp_set_clkname(&pdev->dev, "core");
+ if (IS_ERR(msm_bayhub_host->opp_table)) {
+ ret = PTR_ERR(msm_bayhub_host->opp_table);
+ goto bus_clk_disable;
+ }
+
+ /* OPP table is optional */
+ ret = dev_pm_opp_of_add_table(&pdev->dev);
+ if (!ret) {
+ msm_bayhub_host->has_opp_table = true;
+ } else if (ret != -ENODEV) {
+ dev_err(&pdev->dev, "Invalid OPP table in Device tree\n");
+ goto opp_cleanup;
+ }
+
+ /* Vote for maximum clock rate for maximum performance */
+ ret = dev_pm_opp_set_rate(&pdev->dev, INT_MAX);
+ if (ret)
+ dev_warn(&pdev->dev, "core clock boost failed\n");
+
+ clk = devm_clk_get(&pdev->dev, "cal");
+ if (IS_ERR(clk))
+ clk = NULL;
+ msm_bayhub_host->bulk_clks[2].clk = clk;
+
+ clk = devm_clk_get(&pdev->dev, "sleep");
+ if (IS_ERR(clk))
+ clk = NULL;
+ msm_bayhub_host->bulk_clks[3].clk = clk;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (ret)
+ goto opp_cleanup;
+
+ /*
+ * xo clock is needed for FLL feature of cm_dll.
+ * In case if xo clock is not mentioned in DT, warn and proceed.
+ */
+ msm_bayhub_host->xo_clk = devm_clk_get(&pdev->dev, "xo");
+ if (IS_ERR(msm_bayhub_host->xo_clk)) {
+ ret = PTR_ERR(msm_bayhub_host->xo_clk);
+ dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret);
+ }
+
+ if (!msm_bayhub_host->mci_removed) {
+ core_memres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ msm_bayhub_host->core_mem = devm_ioremap_resource(&pdev->dev,
+ core_memres);
+
+ if (IS_ERR(msm_bayhub_host->core_mem)) {
+ ret = PTR_ERR(msm_bayhub_host->core_mem);
+ goto clk_disable;
+ }
+ }
+
+ /* Reset the vendor spec register to power on reset state */
+ writel_relaxed(CORE_VENDOR_SPEC_POR_VAL,
+ host->ioaddr + msm_bayhub_offset->core_vendor_spec);
+
+ if (!msm_bayhub_host->mci_removed) {
+ /* Set HC_MODE_EN bit in HC_MODE register */
+ msm_bayhub_host_writel(msm_bayhub_host, HC_MODE_EN, host,
+ msm_bayhub_offset->core_hc_mode);
+ config = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_hc_mode);
+ config |= FF_CLK_SW_RST_DIS;
+ msm_bayhub_host_writel(msm_bayhub_host, config, host,
+ msm_bayhub_offset->core_hc_mode);
+ }
+
+ host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
+ dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
+ host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
+ SDHCI_VENDOR_VER_SHIFT));
+
+ core_version = msm_bayhub_host_readl(msm_bayhub_host, host,
+ msm_bayhub_offset->core_mci_version);
+ core_major = (core_version & CORE_VERSION_MAJOR_MASK) >>
+ CORE_VERSION_MAJOR_SHIFT;
+ core_minor = core_version & CORE_VERSION_MINOR_MASK;
+ dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
+ core_version, core_major, core_minor);
+
+ if (core_major == 1 && core_minor >= 0x42)
+ msm_bayhub_host->use_14lpp_dll_reset = true;
+
+ /*
+ * SDCC 5 controller with major version 1, minor version 0x34 and later
+ * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL.
+ */
+ if (core_major == 1 && core_minor < 0x34)
+ msm_bayhub_host->use_cdclp533 = true;
+
+ /*
+ * Support for some capabilities is not advertised by newer
+ * controller versions and must be explicitly enabled.
+ */
+ if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
+ config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
+ config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
+ writel_relaxed(config, host->ioaddr +
+ msm_bayhub_offset->core_vendor_spec_capabilities0);
+ }
+
+ if (core_major == 1 && core_minor >= 0x49)
+ msm_bayhub_host->updated_ddr_cfg = true;
+
+ ret = sdhci_msm_bayhub_register_vreg(msm_bayhub_host);
+ if (ret)
+ goto clk_disable;
+
+ /*
+ * Power on reset state may trigger power irq if previous status of
+ * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq
+ * interrupt in GIC, any pending power irq interrupt should be
+ * acknowledged. Otherwise power irq interrupt handler would be
+ * fired prematurely.
+ */
+ sdhci_msm_bayhub_handle_pwr_irq(host, 0);
+
+ /*
+ * Ensure that above writes are propogated before interrupt enablement
+ * in GIC.
+ */
+ mb();
+
+ /* Setup IRQ for handling power/voltage tasks with PMIC */
+ msm_bayhub_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
+ if (msm_bayhub_host->pwr_irq < 0) {
+ ret = msm_bayhub_host->pwr_irq;
+ goto clk_disable;
+ }
+
+ sdhci_msm_bayhub_init_pwr_irq_wait(msm_bayhub_host);
+ /* Enable pwr irq interrupts */
+ msm_bayhub_host_writel(msm_bayhub_host, INT_MASK, host,
+ msm_bayhub_offset->core_pwrctl_mask);
+
+ ret = devm_request_threaded_irq(&pdev->dev, msm_bayhub_host->pwr_irq, NULL,
+ sdhci_msm_bayhub_pwr_irq, IRQF_ONESHOT,
+ dev_name(&pdev->dev), host);
+ if (ret) {
+ dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret);
+ goto clk_disable;
+ }
+
+ msm_bayhub_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_NEED_RSP_BUSY;
+
+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev,
+ MSM_MMC_AUTOSUSPEND_DELAY_MS);
+ pm_runtime_use_autosuspend(&pdev->dev);
+
+ host->mmc_host_ops.start_signal_voltage_switch =
+ sdhci_msm_bayhub_start_signal_voltage_switch;
+ if (msm_bayhub_host->ggc.bh201_used)
+ host->mmc_host_ops.execute_tuning = sdhci_bht_execute_tuning;
+ else
+ host->mmc_host_ops.execute_tuning = sdhci_msm_bayhub_execute_tuning;
+
+ if (of_property_read_bool(node, "supports-cqe"))
+ ret = sdhci_msm_bayhub_cqe_add_host(host, pdev);
+ else
+ ret = sdhci_add_host(host);
+ if (ret)
+ goto pm_runtime_disable;
+
+ pm_runtime_mark_last_busy(&pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
+ return 0;
+
+pm_runtime_disable:
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+clk_disable:
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+opp_cleanup:
+ if (msm_bayhub_host->has_opp_table)
+ dev_pm_opp_of_remove_table(&pdev->dev);
+ dev_pm_opp_put_clkname(msm_bayhub_host->opp_table);
+bus_clk_disable:
+ if (!IS_ERR(msm_bayhub_host->bus_clk))
+ clk_disable_unprepare(msm_bayhub_host->bus_clk);
+pltfm_free:
+ if (msm_bayhub_host->ggc.bh201_used) {
+ if (gpio_is_valid(msm_bayhub_host->ggc.det_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.det_gpio);
+ if (gpio_is_valid(msm_bayhub_host->ggc.pwr_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.pwr_gpio);
+ }
+
+ sdhci_pltfm_free(pdev);
+ return ret;
+}
+
+static int sdhci_msm_bayhub_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
+ 0xffffffff);
+
+ sdhci_remove_host(host, dead);
+ if (msm_bayhub_host->ggc.bh201_used) {
+ if (gpio_is_valid(msm_bayhub_host->ggc.det_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.det_gpio);
+ if (gpio_is_valid(msm_bayhub_host->ggc.pwr_gpio))
+ devm_gpio_free(&pdev->dev, msm_bayhub_host->ggc.pwr_gpio);
+ }
+ if (msm_bayhub_host->has_opp_table)
+ dev_pm_opp_of_remove_table(&pdev->dev);
+ dev_pm_opp_put_clkname(msm_bayhub_host->opp_table);
+ pm_runtime_get_sync(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (!IS_ERR(msm_bayhub_host->bus_clk))
+ clk_disable_unprepare(msm_bayhub_host->bus_clk);
+ sdhci_pltfm_free(pdev);
+ return 0;
+}
+
+static __maybe_unused int sdhci_msm_bayhub_runtime_suspend(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+
+ /* Drop the performance vote */
+ dev_pm_opp_set_rate(dev, 0);
+ clk_bulk_disable_unprepare(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+
+ return 0;
+}
+
+static __maybe_unused int sdhci_msm_bayhub_runtime_resume(struct device *dev)
+{
+ struct sdhci_host *host = dev_get_drvdata(dev);
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_msm_bayhub_host *msm_bayhub_host = sdhci_pltfm_priv(pltfm_host);
+ int ret;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_bayhub_host->bulk_clks),
+ msm_bayhub_host->bulk_clks);
+ if (ret)
+ return ret;
+ /*
+ * Whenever core-clock is gated dynamically, it's needed to
+ * restore the SDR DLL settings when the clock is ungated.
+ */
+ if (msm_bayhub_host->restore_dll_config && msm_bayhub_host->clk_rate)
+ ret = sdhci_msm_bayhub_restore_sdr_dll_config(host);
+
+ dev_pm_opp_set_rate(dev, msm_bayhub_host->clk_rate);
+
+ return ret;
+}
+
+static const struct dev_pm_ops sdhci_msm_bayhub_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_RUNTIME_PM_OPS(sdhci_msm_bayhub_runtime_suspend,
+ sdhci_msm_bayhub_runtime_resume,
+ NULL)
+};
+
+static struct platform_driver sdhci_msm_bayhub_driver = {
+ .probe = sdhci_msm_bayhub_probe,
+ .remove = sdhci_msm_bayhub_remove,
+ .driver = {
+ .name = "sdhci_msm_bayhub",
+ .of_match_table = sdhci_msm_bayhub_dt_match,
+ .pm = &sdhci_msm_bayhub_pm_ops,
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+};
+
+module_platform_driver(sdhci_msm_bayhub_driver);
+
+MODULE_DESCRIPTION("Qualcomm-bayhub Secure Digital Host Controller Interface driver");
+MODULE_LICENSE("GPL v2");
--
2.25.1
^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2021-11-04 6:51 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-28 17:43 [PATCH V1 1/1]mmc:sdhci-bayhub:fix Qualcomm sd host 845 SD card compatibility issue chevron
2021-08-20 18:20 ` Bjorn Andersson
2021-08-30 12:14 ` 回复: " Chevron Li (WH)
2021-11-04 6:51 ` Chevron Li (WH)
[not found] <20210714010742.4707-1-chevron.li@bayhubtech.com>
2021-07-20 11:43 ` Chevron Li (WH)
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).