RE: [PATCH/RFC 03/12] dt-bindings: panel: lvds: Add dual-link LVDS display support

[Fabrizio Castro <fabrizio.castro@bp.renesas.com>]

Hi Laurent,

Thank you for your feedback!

> From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Sent: 02 August 2019 09:00
> Subject: Re: [PATCH/RFC 03/12] dt-bindings: panel: lvds: Add dual-link LVDS display support
> 
> Hi Fabrizio,
> 
> Thank you for the patch.
> 
> On Fri, Aug 02, 2019 at 08:34:00AM +0100, Fabrizio Castro wrote:
> > Dual-link LVDS displays have two ports, therefore document this
> > with the bindings.
> >
> > Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
> > ---
> >  .../bindings/display/panel/panel-lvds.txt          | 91 ++++++++++++++++------
> >  1 file changed, 67 insertions(+), 24 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> > index 250850a..07795441 100644
> > --- a/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> > +++ b/Documentation/devicetree/bindings/display/panel/panel-lvds.txt
> > @@ -41,7 +41,8 @@ Required nodes:
> >
> >  - panel-timing: See panel-common.txt.
> >  - ports: See panel-common.txt. These bindings require a single port subnode
> > -  corresponding to the panel LVDS input.
> > +  (for a single link display) or two port subnodes (for a dual link display)
> > +  corresponding to the panel LVDS input(s).
> 
> I think you should expand this a bit to explain what the ports
> correspond to in the dual link mode.

Will change.

> 
> >  LVDS data mappings are defined as follows.
> > @@ -92,30 +93,72 @@ CTL3: 0
> >  Example
> >  -------
> >
> > -panel {
> > -	compatible = "mitsubishi,aa121td01", "panel-lvds";
> > -
> > -	width-mm = <261>;
> > -	height-mm = <163>;
> > -
> > -	data-mapping = "jeida-24";
> > -
> > -	panel-timing {
> > -		/* 1280x800 @60Hz */
> > -		clock-frequency = <71000000>;
> > -		hactive = <1280>;
> > -		vactive = <800>;
> > -		hsync-len = <70>;
> > -		hfront-porch = <20>;
> > -		hback-porch = <70>;
> > -		vsync-len = <5>;
> > -		vfront-porch = <3>;
> > -		vback-porch = <15>;
> > +Single port:
> > +	panel {
> > +		compatible = "mitsubishi,aa121td01", "panel-lvds";
> > +
> > +		width-mm = <261>;
> > +		height-mm = <163>;
> > +
> > +		data-mapping = "jeida-24";
> > +
> > +		panel-timing {
> > +			/* 1280x800 @60Hz */
> > +			clock-frequency = <71000000>;
> > +			hactive = <1280>;
> > +			vactive = <800>;
> > +			hsync-len = <70>;
> > +			hfront-porch = <20>;
> > +			hback-porch = <70>;
> > +			vsync-len = <5>;
> > +			vfront-porch = <3>;
> > +			vback-porch = <15>;
> > +		};
> > +
> > +		port {
> > +			panel_in: endpoint {
> > +				remote-endpoint = <&lvds_encoder>;
> > +			};
> > +		};
> >  	};
> >
> > -	port {
> > -		panel_in: endpoint {
> > -			remote-endpoint = <&lvds_encoder>;
> > +Two ports:
> > +	panel {
> > +		compatible = "advantech,idk-2121wr", "panel-lvds";
> > +
> > +		width-mm = <476>;
> > +		height-mm = <268>;
> > +
> > +		data-mapping = "vesa-24";
> > +
> > +		panel-timing {
> > +			clock-frequency = <148500000>;
> > +			hactive = <1920>;
> > +			vactive = <1080>;
> > +			hsync-len = <44>;
> > +			hfront-porch = <88>;
> > +			hback-porch = <148>;
> > +			vfront-porch = <4>;
> > +			vback-porch = <36>;
> > +			vsync-len = <5>;
> > +		};
> > +
> > +		ports {
> > +			#address-cells = <1>;
> > +			#size-cells = <0>;
> > +
> > +			port@0 {
> > +				reg = <0>;
> > +				lvds0_panel_in: endpoint {
> 
> I would name the label panel_in0 and panel_in1 below to have a common
> prefix showing that both refer to the same panel.

I agree, will change, thank you for pointing this out.

> 
> > +					remote-endpoint = <&lvds0_out>;
> > +				};
> > +			};
> > +
> > +			port@1 {
> > +				reg = <1>;
> > +				lvds1_panel_in: endpoint {
> > +					remote-endpoint = <&lvds1_out>;
> > +				};
> > +			};
> >  		};
> >  	};
> > -};

Thanks,
Fab

> 
> --
> Regards,
> 
> Laurent Pinchart