From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 9F2A0C25B50 for ; Fri, 20 Jan 2023 19:06:32 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S229501AbjATTGb (ORCPT ); Fri, 20 Jan 2023 14:06:31 -0500 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:43418 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S229547AbjATTG3 (ORCPT ); Fri, 20 Jan 2023 14:06:29 -0500 Received: from relay7-d.mail.gandi.net (relay7-d.mail.gandi.net [217.70.183.200]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id E0B317A53C; Fri, 20 Jan 2023 11:06:05 -0800 (PST) Received: (Authenticated sender: alexandre.belloni@bootlin.com) by mail.gandi.net (Postfix) with ESMTPSA id C12E120003; Fri, 20 Jan 2023 19:05:07 +0000 (UTC) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=bootlin.com; s=gm1; t=1674241508; h=from:from:reply-to:subject:subject:date:date:message-id:message-id: to:to:cc:cc:mime-version:mime-version:content-type:content-type: in-reply-to:in-reply-to:references:references; bh=9E+QtNt/tZxl4Is0JIBM8KaZdkhA+rSRubd0xlkD1hw=; b=Mb2Fh1aAnkRXnvGascZr+4jUG7mf45VPGVIDZ5JWEclvUMQSA4O8XxOEho9saTFPoLDAKr aolcDJFeJGw+ZBeqA6/cCGJHkYSk0CdX8apdLmW/w2x3vtJjthgcVl7EXkT5Rzi+fCxrmZ Speb6jwBwtbIvnEn9ZsVkozwfZooo9AKsKjBwNWd+Uu2Xlb+DzUsK2AjfN4pt/mUJNwm84 xx5mXRZ69BEilJkI+ofitdBqrDwQh18RefGedM+WqOGhqxdA+i92Aqx4SfGNwsp23GQzEF XGk/mil2kkZrS/pRC04umAlVhesz+bZb+EKGZjEqjUm5AuOJX8o281Zj+iYhtA== Date: Fri, 20 Jan 2023 20:05:07 +0100 From: Alexandre Belloni To: Hugo Villeneuve Cc: a.zummo@towertech.it, robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org, linux-rtc@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Hugo Villeneuve Subject: Re: [PATCH v3 00/14] rtc: pcf2127: add PCF2131 driver Message-ID: References: <20221215150214.1109074-1-hugo@hugovil.com> MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Content-Disposition: inline In-Reply-To: <20221215150214.1109074-1-hugo@hugovil.com> Precedence: bulk List-ID: X-Mailing-List: linux-kernel@vger.kernel.org Hello, I know I've been holding off on the review of this series for a while and I'm sorry for that. One of the main issue that is remaining is that the driver ends up being 53% bigger and generaly less efficient for no added functionality for the existing RTCs. I know performance is not a concern however, having more code in the set/read time and irq paths means that it is more difficult to set an get the time precisely. I guess I'll take it as a merged driver but I took a different decision for other RTCs. On 15/12/2022 10:02:01-0500, Hugo Villeneuve wrote: > From: Hugo Villeneuve > > Hello, > this patch series adds the driver for the PCF2131 real-time clock. > > This RTC is very similar in functionality to the PCF2127/29 with the > following differences: > -supports two new control registers at offsets 4 and 5 > -supports a new reset register > -supports 4 tamper detection functions instead of 1 > -has no nvmem (like the PCF2129) > -has two output interrupt pins instead of one > -has 1/100th seconds capabilities (not supported in this driver) > -pcf2127 has watchdog clock sources: 1/60, 1, 64 and 4096Hz > pcf2131 has watchdog clock sources: 1/64, 1/4, 4 and 64Hz > -watchdog value register cannot be read after being set > > Most of the register addresses are very different, although they still > follow the same layout. For example, the time/date and tamper registers > have a different base address, but the offsets are all the same. > Consequently, the source code of the PCF2127 driver can be easily adapted > to support this new device. > > Patches 1 to 6 modify the existing pcf2127 driver to make it more generic > and able to support multiple variants, like the PCF2131. This is done > mostly by using offsets instead of absolute hardcoded register addresses. > > Patch 7 add actual support for the PCF2131. > > Patch 8 configures all interrupt sources to go through the INT A pin. > > Patch 9 changes the PWRMNG bits to be the same with the PCF2131 as they > are with the PCF2127/29 (different default values). > > Patch 10 allow to confirm PCF2131 device presence by reading the reset > register fixed pattern. > > Patch 11 adapt the time/date registers write sequence for PCF2131 (STOP and > CPR bits). > > Patch 12 add support for generic watchdog timing configuration. > > Patch 13 add a new flag to identify if device has read support for reading > watchdog register value. > Since the watchdog value register cannot be read on the PCF2131 after > being set, it seems that we cannot detect if watchdog timer was > started by bootloader. I am not sure what is the best way to handle > this situation, suggestions are welcomed. > > Patch 14 add the dt-bindings for the PCF2131. > > I have tested the driver using a PCF2131-ARD evaluation board connected to > an NXP imx8mp evaluation board: > - Time get/set ok; > - Alarms get/set ok > - Timestamp 1 to 4 ok > - IRQ alarm ok > - Watchdog ok > - Also tested successfully with "RTC Driver Test Example" from > Documentation/rtc.txt > > I have also tested the driver on a custom PCF2129 adapter board connected to a > beaglebone black. > > Thank you. > > Link: [v1] https://patchwork.ozlabs.org/project/rtc-linux/patch/20220125200009.900660-2-hugo@hugovil.com/ > Link: [v2] https://patchwork.ozlabs.org/project/rtc-linux/list/?series=285734 > > Changes for V3: > - Rebased for kernel v6.1 > > Changes for V2: > - In general, fix and improvements after I have tested on real hardware > - Fix alarm interrupt A/B mask setting for PCF2131: > PCF2131_BIT_INT_AIE must be cleared, not set, to enable interrupt. > - Remove low_reg validation: only check if TS interrupt flag is > defined, as low_reg is defined at address 0 for PCF2127/29. > - Change PWRMNG value for PCF2131: default is different than PCF2127/29. > - Adapt time/date registers write sequence for PCF2131 (STOP and CPR bits). > - Map all interrupt sources to INT A pin > - Read and validate PCF2131 device presence from RESET register > - Adapt watchdog configuration for PCF2131 > > Hugo Villeneuve (14): > rtc: pcf2127: add variant-specific configuration structure > rtc: pcf2127: adapt for time/date registers at any offset > rtc: pcf2127: adapt for alarm registers at any offset > rtc: pcf2127: adapt for WD registers at any offset > rtc: pcf2127: adapt for CLKOUT register at any offset > rtc: pcf2127: add support for multiple TS functions > rtc: pcf2127: add support for PCF2131 RTC > rtc: pcf2127: add support for PCF2131 interrupts on output INT_A > rtc: pcf2127: set PWRMNG value for PCF2131 > rtc: pcf2127: read and validate PCF2131 device signature > rtc: pcf2127: adapt time/date registers write sequence for PCF2131 > rtc: pcf2127: support generic watchdog timing configuration > rtc: pcf2127: add flag for watchdog register value read support > dt-bindings: rtc: pcf2127: add PCF2131 > > .../devicetree/bindings/rtc/nxp,pcf2127.yaml | 4 +- > drivers/rtc/Kconfig | 4 +- > drivers/rtc/rtc-pcf2127.c | 939 ++++++++++++++---- > 3 files changed, 752 insertions(+), 195 deletions(-) > > -- > 2.30.2 > -- Alexandre Belloni, co-owner and COO, Bootlin Embedded Linux and Kernel engineering https://bootlin.com