* [PATCH v2] arm64: dts: qcom: db845c: Add support for MCP2517FD
@ 2022-04-19 4:33 Vinod Koul
2022-04-19 7:37 ` Krzysztof Kozlowski
0 siblings, 1 reply; 3+ messages in thread
From: Vinod Koul @ 2022-04-19 4:33 UTC (permalink / raw)
To: Bjorn Andersson
Cc: linux-arm-msm, Vinod Koul, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Manivannan Sadhasivam
Add support for onboard MCP2517FD SPI CAN transceiver attached to
SPI0 of RB3.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
Changes in v2:
- add cs and pinctrl config
- remove misleading comment
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 33 ++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 28fe45c5d516..4f4d45be93e3 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -28,6 +28,13 @@ chosen {
stdout-path = "serial0:115200n8";
};
+ /* Fixed crystal oscillator dedicated to MCP2517FD */
+ clk40M: can_clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <40000000>;
+ };
+
dc12v: dc12v-regulator {
compatible = "regulator-fixed";
regulator-name = "DC12V";
@@ -746,6 +753,24 @@ codec {
};
};
+&spi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_spi0_default>;
+ cs-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+
+ can@0 {
+ compatible = "microchip,mcp2517fd";
+ reg = <0>;
+ clocks = <&clk40M>;
+ interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <10000000>;
+ vdd-supply = <&vdc_5v>;
+ xceiver-supply = <&vdc_5v>;
+ status = "okay";
+ };
+};
+
&spi2 {
/* On Low speed expansion */
label = "LS-SPI0";
@@ -1219,3 +1244,11 @@ ov7251_ep: endpoint {
};
};
};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+&qup_spi0_default {
+ config {
+ drive-strength = <6>;
+ bias-disable;
+ };
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v2] arm64: dts: qcom: db845c: Add support for MCP2517FD
2022-04-19 4:33 [PATCH v2] arm64: dts: qcom: db845c: Add support for MCP2517FD Vinod Koul
@ 2022-04-19 7:37 ` Krzysztof Kozlowski
2022-04-21 7:23 ` Vinod Koul
0 siblings, 1 reply; 3+ messages in thread
From: Krzysztof Kozlowski @ 2022-04-19 7:37 UTC (permalink / raw)
To: Vinod Koul, Bjorn Andersson
Cc: linux-arm-msm, Rob Herring, Krzysztof Kozlowski, devicetree,
linux-kernel, Manivannan Sadhasivam
On 19/04/2022 06:33, Vinod Koul wrote:
> Add support for onboard MCP2517FD SPI CAN transceiver attached to
> SPI0 of RB3.
>
> Signed-off-by: Vinod Koul <vkoul@kernel.org>
> ---
> Changes in v2:
> - add cs and pinctrl config
> - remove misleading comment
>
> arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 33 ++++++++++++++++++++++
> 1 file changed, 33 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> index 28fe45c5d516..4f4d45be93e3 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> @@ -28,6 +28,13 @@ chosen {
> stdout-path = "serial0:115200n8";
> };
>
> + /* Fixed crystal oscillator dedicated to MCP2517FD */
> + clk40M: can_clock {
No underscores in node names.
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <40000000>;
> + };
> +
> dc12v: dc12v-regulator {
> compatible = "regulator-fixed";
> regulator-name = "DC12V";
> @@ -746,6 +753,24 @@ codec {
> };
> };
>
> +&spi0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_spi0_default>;
> + cs-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
> +
> + can@0 {
> + compatible = "microchip,mcp2517fd";
> + reg = <0>;
> + clocks = <&clk40M>;
> + interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
> + spi-max-frequency = <10000000>;
> + vdd-supply = <&vdc_5v>;
> + xceiver-supply = <&vdc_5v>;
> + status = "okay";
No need for status for new nodes (unless it is an extension of existing
node?), it is okay by default.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v2] arm64: dts: qcom: db845c: Add support for MCP2517FD
2022-04-19 7:37 ` Krzysztof Kozlowski
@ 2022-04-21 7:23 ` Vinod Koul
0 siblings, 0 replies; 3+ messages in thread
From: Vinod Koul @ 2022-04-21 7:23 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Bjorn Andersson, linux-arm-msm, Rob Herring, Krzysztof Kozlowski,
devicetree, linux-kernel, Manivannan Sadhasivam
On 19-04-22, 09:37, Krzysztof Kozlowski wrote:
> On 19/04/2022 06:33, Vinod Koul wrote:
> > Add support for onboard MCP2517FD SPI CAN transceiver attached to
> > SPI0 of RB3.
> >
> > Signed-off-by: Vinod Koul <vkoul@kernel.org>
> > ---
> > Changes in v2:
> > - add cs and pinctrl config
> > - remove misleading comment
> >
> > arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 33 ++++++++++++++++++++++
> > 1 file changed, 33 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> > index 28fe45c5d516..4f4d45be93e3 100644
> > --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> > +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
> > @@ -28,6 +28,13 @@ chosen {
> > stdout-path = "serial0:115200n8";
> > };
> >
> > + /* Fixed crystal oscillator dedicated to MCP2517FD */
> > + clk40M: can_clock {
>
> No underscores in node names.
right, will patch up the original source as well :D
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <40000000>;
> > + };
> > +
> > dc12v: dc12v-regulator {
> > compatible = "regulator-fixed";
> > regulator-name = "DC12V";
> > @@ -746,6 +753,24 @@ codec {
> > };
> > };
> >
> > +&spi0 {
> > + status = "okay";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&qup_spi0_default>;
> > + cs-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
> > +
> > + can@0 {
> > + compatible = "microchip,mcp2517fd";
> > + reg = <0>;
> > + clocks = <&clk40M>;
> > + interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
> > + spi-max-frequency = <10000000>;
> > + vdd-supply = <&vdc_5v>;
> > + xceiver-supply = <&vdc_5v>;
> > + status = "okay";
>
> No need for status for new nodes (unless it is an extension of existing
> node?), it is okay by default.
Yep
--
~Vinod
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-04-21 7:23 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-04-19 4:33 [PATCH v2] arm64: dts: qcom: db845c: Add support for MCP2517FD Vinod Koul
2022-04-19 7:37 ` Krzysztof Kozlowski
2022-04-21 7:23 ` Vinod Koul
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).