From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Manivannan Sadhasivam <mani@kernel.org>,
Jassi Brar <jassisinghbrar@gmail.com>,
Johan Hovold <johan+linaro@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/4] arm64: dts: qcom: add SC8280XP platform
Date: Mon, 20 Jun 2022 22:37:06 -0500 [thread overview]
Message-ID: <YrE84tLOpJtzrNW4@builder.lan> (raw)
In-Reply-To: <79443fb4-5c09-a33f-594d-71ac93cc0317@linaro.org>
On Wed 08 Jun 03:18 CDT 2022, Krzysztof Kozlowski wrote:
> On 07/06/2022 23:41, Bjorn Andersson wrote:
> > Introduce initial support for the Qualcomm SC8280XP platform, aka 8cx
> > Gen 3. This initial contribution supports SMP, CPUfreq, CPU cluster
> > idling, GCC, TLMM, SMMU, RPMh regulators, power-domains and clocks,
> > interconnects, some QUPs, UFS, remoteprocs, USB, watchdog, LLCC and
> > tsens.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > ---
> > arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 2195 ++++++++++++++++++++++++
> > 1 file changed, 2195 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> > new file mode 100644
> > index 000000000000..4143813643ad
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> > @@ -0,0 +1,2195 @@
> > +// SPDX-License-Identifier: BSD-3-Clause
> > +/*
> > + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> > + * Copyright (c) 2022, Linaro Limited
> > + */
> > +
> > +#include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
> > +#include <dt-bindings/clock/qcom,rpmh.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/interconnect/qcom,sc8280xp.h>
> > +#include <dt-bindings/mailbox/qcom-ipcc.h>
> > +#include <dt-bindings/power/qcom-rpmpd.h>
> > +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
> > +#include <dt-bindings/thermal/thermal.h>
> > +
> > +/ {
> > + interrupt-parent = <&intc>;
> > +
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + clocks {
> > + xo_board: xo-board {
>
> xo-board-clk
>
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <38400000>;
>
> The clock is probably on the board, so the frequency should be rather
> defined in DTS.
>
It's an interesting question, but I don't think it's possible to change
the rate of this clock from one board to another.
So I think it's best to keep this in the .dtsi, to avoid unnecessary
duplication.
Thanks for the feedback, will update the remaining things.
Regards,
Bjorn
> > + };
> > +
> > + sleep_clk: sleep-clk {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <32764>;
> > + };
> > + };
>
> (...)
>
> > +
> > + qup1: geniqup@ac0000 {
> > + compatible = "qcom,geni-se-qup";
> > + reg = <0 0x00ac0000 0 0x6000>;
> > + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
> > + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
> > + clock-names = "m-ahb", "s-ahb";
> > + iommus = <&apps_smmu 0x83 0>;
> > +
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + status = "disabled";
> > + };
> > +
> > + ufs_mem_hc: ufshc@1d84000 {
>
> Just "ufs" as node name.
>
> > + compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
> > + "jedec,ufs-2.0";
> > + reg = <0 0x01d84000 0 0x3000>;
> > + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> > + phys = <&ufs_mem_phy_lanes>;
> > + phy-names = "ufsphy";
> > + lanes-per-direction = <2>;
> > + #reset-cells = <1>;
> > + resets = <&gcc GCC_UFS_PHY_BCR>;
> > + reset-names = "rst";
> > +
> > + power-domains = <&gcc UFS_PHY_GDSC>;
> > + required-opps = <&rpmhpd_opp_nom>;
> > +
> > + iommus = <&apps_smmu 0xe0 0x0>;
> > +
> > + clocks = <&gcc GCC_UFS_PHY_AXI_CLK>
> > + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
> > + <&gcc GCC_UFS_PHY_AHB_CLK>,
> > + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
> > + <&rpmhcc RPMH_CXO_CLK>,
> > + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
> > + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> > + <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
> > + clock-names = "core_clk",
> > + "bus_aggr_clk",
> > + "iface_clk",
> > + "core_clk_unipro",
> > + "ref_clk",
> > + "tx_lane0_sync_clk",
> > + "rx_lane0_sync_clk",
> > + "rx_lane1_sync_clk";
> > + freq-table-hz = <75000000 300000000>,
> > + <0 0>,
> > + <0 0>,
> > + <75000000 300000000>,
> > + <0 0>,
> > + <0 0>,
> > + <0 0>,
> > + <0 0>;
> > + status = "disabled";
> > + };
> > +
> > + ufs_mem_phy: phy@1d87000 {
> > + compatible = "qcom,sc8280xp-qmp-ufs-phy";
> > + reg = <0 0x01d87000 0 0xe10>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + clock-names = "ref",
> > + "ref_aux";
> > + clocks = <&rpmhcc RPMH_CXO_CLK>,
> > + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
> > +
> > + resets = <&ufs_mem_hc 0>;
> > + reset-names = "ufsphy";
> > + status = "disabled";
> > +
> > + ufs_mem_phy_lanes: phy@1d87400 {
> > + reg = <0 0x01d87400 0 0x108>,
> > + <0 0x01d87600 0 0x1e0>,
> > + <0 0x01d87c00 0 0x1dc>,
> > + <0 0x01d87800 0 0x108>,
> > + <0 0x01d87a00 0 0x1e0>;
> > + #phy-cells = <0>;
> > + #clock-cells = <0>;
> > + };
> > + };
> > +
> > + ufs_card_hc: ufshc@1da4000 {
>
> node name: ufs
>
> > + compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
> > + "jedec,ufs-2.0";
> > + reg = <0 0x01da4000 0 0x3000>;
> > + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
> > + phys = <&ufs_card_phy_lanes>;
> > + phy-names = "ufsphy";
> > + lanes-per-direction = <2>;
> > + #reset-cells = <1>;
> > + resets = <&gcc GCC_UFS_CARD_BCR>;
> > + reset-names = "rst";
> > +
> > + power-domains = <&gcc UFS_CARD_GDSC>;
> > +
> > + iommus = <&apps_smmu 0x4a0 0x0>;
> > +
> > + clocks = <&gcc GCC_UFS_CARD_AXI_CLK>,
> > + <&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>,
> > + <&gcc GCC_UFS_CARD_AHB_CLK>,
> > + <&gcc GCC_UFS_CARD_UNIPRO_CORE_CLK>,
> > + <&rpmhcc RPMH_CXO_CLK>,
> > + <&gcc GCC_UFS_CARD_TX_SYMBOL_0_CLK>,
> > + <&gcc GCC_UFS_CARD_RX_SYMBOL_0_CLK>,
> > + <&gcc GCC_UFS_CARD_RX_SYMBOL_1_CLK>;
> > + clock-names = "core_clk",
> > + "bus_aggr_clk",
> > + "iface_clk",
> > + "core_clk_unipro",
> > + "ref_clk",
> > + "tx_lane0_sync_clk",
> > + "rx_lane0_sync_clk",
> > + "rx_lane1_sync_clk";
> > + freq-table-hz = <75000000 300000000>,
> > + <0 0>,
> > + <0 0>,
> > + <75000000 300000000>,
> > + <0 0>,
> > + <0 0>,
> > + <0 0>,
> > + <0 0>;
> > + status = "disabled";
> > + };
> > +
> > + ufs_card_phy: phy@1da7000 {
> > + compatible = "qcom,sc8280xp-qmp-ufs-phy";
> > + reg = <0 0x01da7000 0 0xe10>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + clock-names = "ref",
> > + "ref_aux";
> > + clocks = <&gcc GCC_UFS_1_CARD_CLKREF_CLK>,
> > + <&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
> > +
> > + resets = <&ufs_card_hc 0>;
> > + reset-names = "ufsphy";
> > + status = "disabled";
> > +
> > + ufs_card_phy_lanes: phy@1da7400 {
> > + reg = <0 0x01da7400 0 0x108>,
> > + <0 0x01da7600 0 0x1e0>,
> > + <0 0x01da7c00 0 0x1dc>,
> > + <0 0x01da7800 0 0x108>,
> > + <0 0x01da7a00 0 0x1e0>;
> > + #phy-cells = <0>;
> > + #clock-cells = <0>;
> > + };
> > + };
> > +
> > + tcsr_mutex: hwlock@1f40000 {
> > + compatible = "qcom,tcsr-mutex";
> > + reg = <0x0 0x01f40000 0x0 0x20000>;
> > + #hwlock-cells = <1>;
> > + };
> > +
> > + usb_0_hsphy: phy@88e5000 {
> > + compatible = "qcom,sc8280xp-usb-hs-phy",
> > + "qcom,usb-snps-hs-5nm-phy";
> > + reg = <0 0x088e5000 0 0x400>;
> > + status = "disabled";
>
> status goes to the end
>
> > + #phy-cells = <0>;
> > +
> > + clocks = <&gcc GCC_USB2_HS0_CLKREF_CLK>;
> > + clock-names = "ref";
> > +
> > + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
> > + };
> > +
> > + usb_2_hsphy0: phy@88e7000 {
> > + compatible = "qcom,sc8280xp-usb-hs-phy",
> > + "qcom,usb-snps-hs-5nm-phy";
> > + reg = <0 0x088e7000 0 0x400>;
> > + status = "disabled";
>
> ditto
>
> > + #phy-cells = <0>;
> > +
> > + clocks = <&gcc GCC_USB2_HS0_CLKREF_CLK>;
> > + clock-names = "ref";
> > +
> > + resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>;
> > + };
> > +
> > + usb_2_hsphy1: phy@88e8000 {
> > + compatible = "qcom,sc8280xp-usb-hs-phy",
> > + "qcom,usb-snps-hs-5nm-phy";
> > + reg = <0 0x088e8000 0 0x400>;
> > + status = "disabled";
>
> ditto
>
> > + #phy-cells = <0>;
> > +
> > + clocks = <&gcc GCC_USB2_HS1_CLKREF_CLK>;
> > + clock-names = "ref";
> > +
> > + resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>;
> > + };
> > +
> > + usb_2_hsphy2: phy@88e9000 {
> > + compatible = "qcom,sc8280xp-usb-hs-phy",
> > + "qcom,usb-snps-hs-5nm-phy";
> > + reg = <0 0x088e9000 0 0x400>;
> > + status = "disabled";
>
> ditto and so on
>
> Best regards,
> Krzysztof
next prev parent reply other threads:[~2022-06-21 3:37 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-06-07 21:41 [PATCH 0/4] arm64: dts: qcom: Introduce SC8280XP Bjorn Andersson
2022-06-07 21:41 ` [PATCH 1/4] dt-bindings: mailbox: qcom-ipcc: Add NSP1 client Bjorn Andersson
2022-06-08 7:59 ` Krzysztof Kozlowski
2022-08-02 3:28 ` Jassi Brar
2022-06-07 21:41 ` [PATCH 2/4] arm64: dts: qcom: add SC8280XP platform Bjorn Andersson
2022-06-08 8:18 ` Krzysztof Kozlowski
2022-06-21 3:37 ` Bjorn Andersson [this message]
2022-06-21 6:53 ` Krzysztof Kozlowski
2022-06-22 3:32 ` Bjorn Andersson
2022-06-22 14:44 ` Krzysztof Kozlowski
2022-06-08 16:00 ` Johan Hovold
2022-06-23 5:22 ` Vinod Koul
2022-06-23 6:42 ` Johan Hovold
2022-06-07 21:41 ` [PATCH 3/4] arm64: dts: qcom: sc8280x: Add reference device Bjorn Andersson
2022-06-08 8:24 ` Krzysztof Kozlowski
2022-06-08 16:17 ` Johan Hovold
2022-06-21 3:39 ` Bjorn Andersson
2022-06-07 21:41 ` [PATCH 4/4] arm64: dts: qcom: add SA8540P and ADP Bjorn Andersson
2022-06-08 8:26 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YrE84tLOpJtzrNW4@builder.lan \
--to=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jassisinghbrar@gmail.com \
--cc=johan+linaro@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mani@kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).