* [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc
@ 2021-07-05 15:50 Shaik Sajida Bhanu
2021-07-15 5:29 ` Adrian Hunter
0 siblings, 1 reply; 3+ messages in thread
From: Shaik Sajida Bhanu @ 2021-07-05 15:50 UTC (permalink / raw)
To: adrian.hunter, ulf.hansson
Cc: asutoshd, stummala, vbadigan, rampraka, sayalil, sartgarg,
rnayak, cang, pragalla, nitirawa, linux-mmc, linux-kernel,
linux-arm-msm, agross, bjorn.andersson, robh+dt,
Shaik Sajida Bhanu
Whenever SDHC run at clock rate 50MHZ or below, the hardware data
timeout value will be 21.47secs, which is approx. 22secs and we have
a current software timeout value as 10secs. We have to set software
timeout value more than the hardware data timeout value to avioid seeing
the below register dumps.
[ 332.953670] mmc2: Timeout waiting for hardware interrupt.
[ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00007202
[ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001
[ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000027
[ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl: 0x0000001f
[ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap: 0x00000000
[ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007
[ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000000
[ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b
[ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x0000808f
[ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr: 0x00000000
[ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x00000000
[ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000
[ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr:
0x0000000ffffff218
[ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
-----------
[ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
0x6000642c | DLL cfg2: 0x0020a000
[ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
0x00000000 | DDR cfg: 0x80040873
[ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
0xf88218a8 Vndr func3: 0x02626040
[ 333.102371] mmc2: sdhci: ============================================
So, set software timeout value more than hardware timeout value.
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
---
Changes since V2:
- Updated 22 with 22LL to avoid compiler warning as suggested by
Adrian Hunter.
- Added a check to update software data timeout value if its value is
less than the calculated hardware data timeout value as suggested
by Veerabhadrarao Badiganti.
Changes since V1:
- Moved software data timeout update part to qcom specific file
as suggested by Veerabhadrarao Badiganti.
---
drivers/mmc/host/sdhci-msm.c | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index e44b7a6..64fb85e 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
sdhci_cqe_disable(mmc, recovery);
}
+static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
+{
+
+ u32 count, start = 15;
+
+ __sdhci_set_timeout(host, cmd);
+ count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
+ /*
+ * Update software timeout value if its value is less than hardware data
+ * timeout value. Qcom SoC hardware data timeout value was calculated
+ * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
+ */
+ if (cmd && cmd->data && host->clock > 400000 && host->clock <= 50000000
+ && ((1 << (count + start)) > (10 * host->clock)))
+ host->data_timeout = 22LL * NSEC_PER_SEC;
+}
+
static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
.enable = sdhci_msm_cqe_enable,
.disable = sdhci_msm_cqe_disable,
@@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
.irq = sdhci_msm_cqe_irq,
.dump_vendor_regs = sdhci_msm_dump_vendor_regs,
.set_power = sdhci_set_power_noreg,
+ .set_timeout = sdhci_msm_set_timeout,
};
static const struct sdhci_pltfm_data sdhci_msm_pdata = {
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc
2021-07-05 15:50 [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc Shaik Sajida Bhanu
@ 2021-07-15 5:29 ` Adrian Hunter
2021-07-16 6:18 ` sbhanu
0 siblings, 1 reply; 3+ messages in thread
From: Adrian Hunter @ 2021-07-15 5:29 UTC (permalink / raw)
To: Shaik Sajida Bhanu, ulf.hansson
Cc: asutoshd, stummala, vbadigan, rampraka, sayalil, sartgarg,
rnayak, cang, pragalla, nitirawa, linux-mmc, linux-kernel,
linux-arm-msm, agross, bjorn.andersson, robh+dt
On 5/07/21 6:50 pm, Shaik Sajida Bhanu wrote:
> Whenever SDHC run at clock rate 50MHZ or below, the hardware data
> timeout value will be 21.47secs, which is approx. 22secs and we have
> a current software timeout value as 10secs. We have to set software
> timeout value more than the hardware data timeout value to avioid seeing
> the below register dumps.
>
> [ 332.953670] mmc2: Timeout waiting for hardware interrupt.
> [ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
> [ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version: 0x00007202
> [ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000001
> [ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000027
> [ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl: 0x0000001f
> [ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap: 0x00000000
> [ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x00000007
> [ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat: 0x00000000
> [ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab: 0x03ff100b
> [ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
> [ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1: 0x0000808f
> [ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr: 0x00000000
> [ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]: 0x00000000
> [ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
> [ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000
> [ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr:
> 0x0000000ffffff218
> [ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
> -----------
> [ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
> 0x6000642c | DLL cfg2: 0x0020a000
> [ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
> 0x00000000 | DDR cfg: 0x80040873
> [ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
> 0xf88218a8 Vndr func3: 0x02626040
> [ 333.102371] mmc2: sdhci: ============================================
>
> So, set software timeout value more than hardware timeout value.
>
> Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
A couple of minor nitpicks below. Fix those and you can add:
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
> ---
>
> Changes since V2:
> - Updated 22 with 22LL to avoid compiler warning as suggested by
> Adrian Hunter.
> - Added a check to update software data timeout value if its value is
> less than the calculated hardware data timeout value as suggested
> by Veerabhadrarao Badiganti.
>
> Changes since V1:
> - Moved software data timeout update part to qcom specific file
> as suggested by Veerabhadrarao Badiganti.
> ---
> drivers/mmc/host/sdhci-msm.c | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
> index e44b7a6..64fb85e 100644
> --- a/drivers/mmc/host/sdhci-msm.c
> +++ b/drivers/mmc/host/sdhci-msm.c
> @@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
> sdhci_cqe_disable(mmc, recovery);
> }
>
> +static void sdhci_msm_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
> +{
> +
Unnecessary blank line.
> + u32 count, start = 15;
> +
> + __sdhci_set_timeout(host, cmd);
> + count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
> + /*
> + * Update software timeout value if its value is less than hardware data
> + * timeout value. Qcom SoC hardware data timeout value was calculated
> + * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
> + */
> + if (cmd && cmd->data && host->clock > 400000 && host->clock <= 50000000
> + && ((1 << (count + start)) > (10 * host->clock)))
'&&' is better at the end of the previous line
Also fewer parenthesis is more readable e.g.
if (cmd && cmd->data && host->clock > 400000 &&
host->clock <= 50000000 &&
(1 << (count + start)) > (10 * host->clock))
> + host->data_timeout = 22LL * NSEC_PER_SEC;
> +}
> +
> static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
> .enable = sdhci_msm_cqe_enable,
> .disable = sdhci_msm_cqe_disable,
> @@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
> .irq = sdhci_msm_cqe_irq,
> .dump_vendor_regs = sdhci_msm_dump_vendor_regs,
> .set_power = sdhci_set_power_noreg,
> + .set_timeout = sdhci_msm_set_timeout,
> };
>
> static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc
2021-07-15 5:29 ` Adrian Hunter
@ 2021-07-16 6:18 ` sbhanu
0 siblings, 0 replies; 3+ messages in thread
From: sbhanu @ 2021-07-16 6:18 UTC (permalink / raw)
To: Adrian Hunter
Cc: ulf.hansson, asutoshd, stummala, vbadigan, rampraka, sayalil,
sartgarg, rnayak, cang, pragalla, nitirawa, linux-mmc,
linux-kernel, linux-arm-msm, agross, bjorn.andersson, robh+dt
On 2021-07-15 10:59, Adrian Hunter wrote:
> On 5/07/21 6:50 pm, Shaik Sajida Bhanu wrote:
>> Whenever SDHC run at clock rate 50MHZ or below, the hardware data
>> timeout value will be 21.47secs, which is approx. 22secs and we have
>> a current software timeout value as 10secs. We have to set software
>> timeout value more than the hardware data timeout value to avioid
>> seeing
>> the below register dumps.
>>
>> [ 332.953670] mmc2: Timeout waiting for hardware interrupt.
>> [ 332.959608] mmc2: sdhci: ============ SDHCI REGISTER DUMP
>> ===========
>> [ 332.966450] mmc2: sdhci: Sys addr: 0x00000000 | Version:
>> 0x00007202
>> [ 332.973256] mmc2: sdhci: Blk size: 0x00000200 | Blk cnt:
>> 0x00000001
>> [ 332.980054] mmc2: sdhci: Argument: 0x00000000 | Trn mode:
>> 0x00000027
>> [ 332.986864] mmc2: sdhci: Present: 0x01f801f6 | Host ctl:
>> 0x0000001f
>> [ 332.993671] mmc2: sdhci: Power: 0x00000001 | Blk gap:
>> 0x00000000
>> [ 333.000583] mmc2: sdhci: Wake-up: 0x00000000 | Clock:
>> 0x00000007
>> [ 333.007386] mmc2: sdhci: Timeout: 0x0000000e | Int stat:
>> 0x00000000
>> [ 333.014182] mmc2: sdhci: Int enab: 0x03ff100b | Sig enab:
>> 0x03ff100b
>> [ 333.020976] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int:
>> 0x00000000
>> [ 333.027771] mmc2: sdhci: Caps: 0x322dc8b2 | Caps_1:
>> 0x0000808f
>> [ 333.034561] mmc2: sdhci: Cmd: 0x0000183a | Max curr:
>> 0x00000000
>> [ 333.041359] mmc2: sdhci: Resp[0]: 0x00000900 | Resp[1]:
>> 0x00000000
>> [ 333.048157] mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]:
>> 0x00000000
>> [ 333.054945] mmc2: sdhci: Host ctl2: 0x00000000
>> [ 333.059657] mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr:
>> 0x0000000ffffff218
>> [ 333.067178] mmc2: sdhci_msm: ----------- VENDOR REGISTER DUMP
>> -----------
>> [ 333.074343] mmc2: sdhci_msm: DLL sts: 0x00000000 | DLL cfg:
>> 0x6000642c | DLL cfg2: 0x0020a000
>> [ 333.083417] mmc2: sdhci_msm: DLL cfg3: 0x00000000 | DLL usr ctl:
>> 0x00000000 | DDR cfg: 0x80040873
>> [ 333.092850] mmc2: sdhci_msm: Vndr func: 0x00008a9c | Vndr func2 :
>> 0xf88218a8 Vndr func3: 0x02626040
>> [ 333.102371] mmc2: sdhci:
>> ============================================
>>
>> So, set software timeout value more than hardware timeout value.
>>
>> Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
>
> A couple of minor nitpicks below. Fix those and you can add:
>
> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
>
>> ---
>>
>> Changes since V2:
>> - Updated 22 with 22LL to avoid compiler warning as suggested by
>> Adrian Hunter.
>> - Added a check to update software data timeout value if its value is
>> less than the calculated hardware data timeout value as suggested
>> by Veerabhadrarao Badiganti.
>>
>> Changes since V1:
>> - Moved software data timeout update part to qcom specific file
>> as suggested by Veerabhadrarao Badiganti.
>> ---
>> drivers/mmc/host/sdhci-msm.c | 18 ++++++++++++++++++
>> 1 file changed, 18 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci-msm.c
>> b/drivers/mmc/host/sdhci-msm.c
>> index e44b7a6..64fb85e 100644
>> --- a/drivers/mmc/host/sdhci-msm.c
>> +++ b/drivers/mmc/host/sdhci-msm.c
>> @@ -2089,6 +2089,23 @@ static void sdhci_msm_cqe_disable(struct
>> mmc_host *mmc, bool recovery)
>> sdhci_cqe_disable(mmc, recovery);
>> }
>>
>> +static void sdhci_msm_set_timeout(struct sdhci_host *host, struct
>> mmc_command *cmd)
>> +{
>> +
>
> Unnecessary blank line.
Sure i will address this in my next patch set , Thanks for the review.
>
>> + u32 count, start = 15;
>> +
>> + __sdhci_set_timeout(host, cmd);
>> + count = sdhci_readb(host, SDHCI_TIMEOUT_CONTROL);
>> + /*
>> + * Update software timeout value if its value is less than hardware
>> data
>> + * timeout value. Qcom SoC hardware data timeout value was
>> calculated
>> + * using 4 * MCLK * 2^(count + 13). where MCLK = 1 / host->clock.
>> + */
>> + if (cmd && cmd->data && host->clock > 400000 && host->clock <=
>> 50000000
>> + && ((1 << (count + start)) > (10 * host->clock)))
>
> '&&' is better at the end of the previous line
>
> Also fewer parenthesis is more readable e.g.
>
> if (cmd && cmd->data && host->clock > 400000 &&
> host->clock <= 50000000 &&
> (1 << (count + start)) > (10 * host->clock))
>
Sure i will address this in my next patch set , Thanks for the review.
>> + host->data_timeout = 22LL * NSEC_PER_SEC;
>> +}
>> +
>> static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
>> .enable = sdhci_msm_cqe_enable,
>> .disable = sdhci_msm_cqe_disable,
>> @@ -2438,6 +2455,7 @@ static const struct sdhci_ops sdhci_msm_ops = {
>> .irq = sdhci_msm_cqe_irq,
>> .dump_vendor_regs = sdhci_msm_dump_vendor_regs,
>> .set_power = sdhci_set_power_noreg,
>> + .set_timeout = sdhci_msm_set_timeout,
>> };
>>
>> static const struct sdhci_pltfm_data sdhci_msm_pdata = {
>>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-07-16 6:18 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-05 15:50 [PATCH V3] mmc: sdhci-msm: Update the software timeout value for sdhc Shaik Sajida Bhanu
2021-07-15 5:29 ` Adrian Hunter
2021-07-16 6:18 ` sbhanu
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).