Re: [PATCH v3 3/4] arm64: dts: qcom: Add base QDU1000/QRU1000 DTSIs

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 26/10/2022 16:04, Melody Olvera wrote:
> Add the base DTSI files for QDU1000 and QRU1000 SoCs, including base
> descriptions of CPUs, GCC, RPMHCC, QUP, TLMM, and interrupt-controller
> to boot to shell with console on these SoCs.
> 
> Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
> ---
>  arch/arm64/boot/dts/qcom/qdu1000.dtsi | 1406 +++++++++++++++++++++++++

Please use scripts/get_maintainers.pl to get a list of necessary people
and lists to CC.  It might happen, that command when run on an older
kernel, gives you outdated entries.  Therefore please be sure you base
your patches on recent Linux kernel.

>  arch/arm64/boot/dts/qcom/qru1000.dtsi |   27 +
>  2 files changed, 1433 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/qdu1000.dtsi
>  create mode 100644 arch/arm64/boot/dts/qcom/qru1000.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/qdu1000.dtsi b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
> new file mode 100644
> index 000000000000..76474106e931
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qdu1000.dtsi
> @@ -0,0 +1,1406 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022 Qualcomm Innovation Center, Inc. All rights reserved.
> + */

(...)

> +
> +	soc: soc@0 {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges = <0 0 0 0 0x10 0>;
> +		dma-ranges = <0 0 0 0 0x10 0>;
> +		compatible = "simple-bus";
> +
> +		gcc: clock-controller@80000 {
> +			compatible = "qcom,gcc-qdu1000", "syscon";
> +			reg = <0x0 0x80000 0x0 0x1f4200>;
> +			#clock-cells = <1>;
> +			#reset-cells = <1>;
> +			#power-domain-cells = <1>;
> +			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
> +			clock-names = "bi_tcxo", "sleep_clk";
> +		};
> +
> +		gpi_dma0: dma-controller@900000  {
> +			compatible = "qcom,sm6350-gpi-dma";

You should add here a specific compatible as well. Same in other places.
All places. I had impression we talked about this few times, so I don't
know what is missing on your side.

This must be:
"qcom,qdu1000-gpi-dma", "qcom,sm6350-gpi-dma"

> +			#dma-cells = <3>;
> +			reg = <0x0 0x900000 0x0 0x60000>;
> +			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> +			dma-channels = <12>;
> +			dma-channel-mask = <0x3f>;
> +			iommus = <&apps_smmu 0xf6 0x0>;
> +		};
> +

(...)


> +
> +		tlmm: pinctrl@f000000 {
> +			compatible = "qcom,qdu1000-tlmm";
> +			reg = <0x0 0xf000000 0x0 0x1000000>;
> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			gpio-ranges = <&tlmm 0 0 151>;
> +			wakeup-parent = <&pdc>;
> +
> +			qup_uart0_default: qup-uart0-default-state {
> +				pins = "gpio6", "gpio7", "gpio8", "gpio9";
> +				function = "qup00";
> +			};
> +
> +			qup_i2c1_data_clk: qup-i2c1-data-clk-state {
> +				pins = "gpio10", "gpio11";
> +				function = "qup01";
> +				drive-strength = <2>;

Can we have some generic agreement where to put drive-strengths and bias?

See also:
https://lore.kernel.org/linux-devicetree/20221026200357.391635-2-krzysztof.kozlowski@linaro.org/

https://lore.kernel.org/lkml/CAD=FV=VUL4GmjaibAMhKNdpEso_Hg_R=XeMaqah1LSj_9-Ce4Q@mail.gmail.com/

> +				bias-pull-up;
> +			};

(...)

> +		};
> +
> +		cpufreq_hw: cpufreq@17d90000 {
> +			compatible = "qcom,sm8250-cpufreq-epss", "qcom,cpufreq-epss";

This is not sm8250...

> +			reg = <0x0 0x17d90000 0x0 0x1000>, <0x0 0x17d91000 0x0 0x1000>;
> +			reg-names = "freq-domain0", "freq-domain1";
> +			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
> +			clock-names = "xo", "alternate";
> +			#freq-domain-cells = <1>;
> +		};
> +
> +		gem_noc: interconnect@19100000 {
> +			reg = <0x0 0x19100000 0x0 0xB8080>;
> +			compatible = "qcom,qdu1000-gem-noc";
> +			#interconnect-cells = <1>;
> +			qcom,bcm-voters = <&apps_bcm_voter>;
> +		};
> +	};

Best regards,
Krzysztof