linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lubomir Rintel <lkundrak@v3.sk>
To: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>,
	Neil Armstrong <narmstrong@baylibre.com>,
	Jonas Karlman <jonas@kwiboo.se>,
	Jernej Skrabec <jernej.skrabec@siol.net>,
	Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	David Airlie <airlied@linux.ie>, Daniel Vetter <daniel@ffwll.ch>,
	dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH 3/3] drm/bridge: chrontel-ch7033: Add a new driver
Date: Sat, 11 Jan 2020 00:00:55 +0100	[thread overview]
Message-ID: <b3a08fc36f19347e50b9fe0943287503d7f39cf7.camel@v3.sk> (raw)
In-Reply-To: <20200108152036.GF4884@pendragon.ideasonboard.com>

Hello Laurent,

On Wed, 2020-01-08 at 17:20 +0200, Laurent Pinchart wrote:
> Hi Lubomir,
> 
> Thank you for the patch.
> 
> On Fri, Dec 20, 2019 at 08:49:14AM +0100, Lubomir Rintel wrote:
> > This is a driver for video encoder with VGA and DVI/HDMI outputs.
> > 
> > There is no documentation for the chip -- the operation was guessed from
> > what was sniffed on a Dell Wyse 3020 ThinOS terminal, the register names
> > come from the ch7035 driver in Mediatek's GPL code dump.
> > 
> > Only bare minimum is implemented -- no fancy stuff, such as scaling. That
> > would only worsen our misery. We don't load the firmware and we don't need
> > to even bother enabling the MCU.  There are probably no distributable
> > firmware images anyway.
> > 
> > Just like the tda998x driver, this one uses the component framework and
> > adds an encoder on component bind, so that it works with the Armada DRM
> > driver.
> 
> Any chance the Armada DRM driver could use of_drm_find_bridge() to avoid
> having to use the component framework everywhere ?

Thanks for the response.

I've brought this up previously and the Armada DRM maintainer pointed
out that drm_bridge_remove() is essentialy a surprise removal [1].
Unlike the component unbind, it doesn't let the crtc driver know that
the bridge is gone. Understandably, he wasn't too fond of the idea of
losing the ability to unload the bridge driver and not much has changed
since.

[1] https://www.spinics.net/lists/dri-devel/msg201927.html

This shouldn't be too much of a problem (other than extra LOC in the
driver), because the bridge is registered outside the component bind
path, therefore the drivers that choose not to use the component
framework can use just the bridge alone just fine.

Thank you
Lubo

> > Tested with a handful of monitors ranging from 1024x768@75 to 1400x1050@60,
> > with VGA as well as DVI.
> > 
> > Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
> > ---
> >  drivers/gpu/drm/bridge/Kconfig           |  10 +
> >  drivers/gpu/drm/bridge/Makefile          |   1 +
> >  drivers/gpu/drm/bridge/chrontel-ch7033.c | 722 +++++++++++++++++++++++
> >  3 files changed, 733 insertions(+)
> >  create mode 100644 drivers/gpu/drm/bridge/chrontel-ch7033.c
> > 
> > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> > index 34362976cd6fd..9456ea968c5b7 100644
> > --- a/drivers/gpu/drm/bridge/Kconfig
> > +++ b/drivers/gpu/drm/bridge/Kconfig
> > @@ -37,6 +37,16 @@ config DRM_CDNS_DSI
> >  	  Support Cadence DPI to DSI bridge. This is an internal
> >  	  bridge and is meant to be directly embedded in a SoC.
> >  
> > +config DRM_CHRONTEL_CH7033
> > +	tristate "Chrontel CH7033 Video Encoder"
> > +	depends on OF
> > +	select DRM_KMS_HELPER
> > +	help
> > +	  Enable support for the Chrontel CH7033 VGA/DVI/HDMI Encoder, as
> > +	  found in the Dell Wyse 3020 thin client.
> > +
> > +	  If in doubt, say "N".
> > +
> >  config DRM_DUMB_VGA_DAC
> >  	tristate "Dumb VGA DAC Bridge support"
> >  	depends on OF
> > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> > index 4934fcf5a6f82..74a9ab2f17468 100644
> > --- a/drivers/gpu/drm/bridge/Makefile
> > +++ b/drivers/gpu/drm/bridge/Makefile
> > @@ -1,6 +1,7 @@
> >  # SPDX-License-Identifier: GPL-2.0
> >  obj-$(CONFIG_DRM_ANALOGIX_ANX78XX) += analogix-anx78xx.o
> >  obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
> > +obj-$(CONFIG_DRM_CHRONTEL_CH7033) += chrontel-ch7033.o
> >  obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> >  obj-$(CONFIG_DRM_LVDS_ENCODER) += lvds-encoder.o
> >  obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
> > diff --git a/drivers/gpu/drm/bridge/chrontel-ch7033.c b/drivers/gpu/drm/bridge/chrontel-ch7033.c
> > new file mode 100644
> > index 0000000000000..a3b63984226a4
> > --- /dev/null
> > +++ b/drivers/gpu/drm/bridge/chrontel-ch7033.c
> > @@ -0,0 +1,722 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Chrontel CH7033 Video Encoder Driver
> > + *
> > + * Copyright (C) 2019 Lubomir Rintel
> > + */
> > +
> > +#include <linux/component.h>
> > +#include <linux/module.h>
> > +#include <linux/gpio/consumer.h>
> 
> Could you please sort these alphabetically ?
> 
> > +
> > +#include <drm/drm_atomic_helper.h>
> > +#include <drm/drm_bridge.h>
> > +#include <drm/drm_edid.h>
> > +#include <drm/drm_of.h>
> > +#include <drm/drm_print.h>
> > +#include <drm/drm_probe_helper.h>
> > +
> > +/* Page 0, Register 0x07 */
> > +enum {
> > +	DRI_PD		= BIT(3),
> > +	IO_PD		= BIT(5),
> > +};
> > +
> > +/* Page 0, Register 0x08 */
> > +enum {
> > +	DRI_PDDRI	= GENMASK(7, 4),
> > +	PDDAC		= GENMASK(3, 1),
> > +	PANEN		= BIT(0),
> > +};
> > +
> > +/* Page 0, Register 0x09 */
> > +enum {
> > +	DPD		= BIT(7),
> > +	GCKOFF		= BIT(6),
> > +	TV_BP		= BIT(5),
> > +	SCLPD		= BIT(4),
> > +	SDPD		= BIT(3),
> > +	VGA_PD		= BIT(2),
> > +	HDBKPD		= BIT(1),
> > +	HDMI_PD		= BIT(0),
> > +};
> > +
> > +/* Page 0, Register 0x0a */
> > +enum {
> > +	MEMINIT		= BIT(7),
> > +	MEMIDLE		= BIT(6),
> > +	MEMPD		= BIT(5),
> > +	STOP		= BIT(4),
> > +	LVDS_PD		= BIT(3),
> > +	HD_DVIB		= BIT(2),
> > +	HDCP_PD		= BIT(1),
> > +	MCU_PD		= BIT(0),
> > +};
> > +
> > +/* Page 0, Register 0x18 */
> > +enum {
> > +	IDF		= GENMASK(7, 4),
> > +	INTEN		= BIT(3),
> > +	SWAP		= GENMASK(2, 0),
> > +};
> > +
> > +enum {
> > +	BYTE_SWAP_RGB	= 0,
> > +	BYTE_SWAP_RBG	= 1,
> > +	BYTE_SWAP_GRB	= 2,
> > +	BYTE_SWAP_GBR	= 3,
> > +	BYTE_SWAP_BRG	= 4,
> > +	BYTE_SWAP_BGR	= 5,
> > +};
> > +
> > +/* Page 0, Register 0x19 */
> > +enum {
> > +	HPO_I		= BIT(5),
> > +	VPO_I		= BIT(4),
> > +	DEPO_I		= BIT(3),
> > +	CRYS_EN		= BIT(2),
> > +	GCLKFREQ	= GENMASK(2, 0),
> > +};
> > +
> > +/* Page 0, Register 0x2e */
> > +enum {
> > +	HFLIP		= BIT(7),
> > +	VFLIP		= BIT(6),
> > +	DEPO_O		= BIT(5),
> > +	HPO_O		= BIT(4),
> > +	VPO_O		= BIT(3),
> > +	TE		= GENMASK(2, 0),
> > +};
> > +
> > +/* Page 0, Register 0x2b */
> > +enum {
> > +	SWAPS		= GENMASK(7, 4),
> > +	VFMT		= GENMASK(3, 0),
> > +};
> > +
> > +/* Page 0, Register 0x54 */
> > +enum {
> > +	COMP_BP		= BIT(7),
> > +	DAC_EN_T	= BIT(6),
> > +	HWO_HDMI_HI	= GENMASK(5, 3),
> > +	HOO_HDMI_HI	= GENMASK(2, 0),
> > +};
> > +
> > +/* Page 0, Register 0x57 */
> > +enum {
> > +	FLDSEN		= BIT(7),
> > +	VWO_HDMI_HI	= GENMASK(5, 3),
> > +	VOO_HDMI_HI	= GENMASK(2, 0),
> > +};
> > +
> > +/* Page 0, Register 0x7e */
> > +enum {
> > +	HDMI_LVDS_SEL	= BIT(7),
> > +	DE_GEN		= BIT(6),
> > +	PWM_INDEX_HI	= BIT(5),
> > +	USE_DE		= BIT(4),
> > +	R_INT		= GENMASK(3, 0),
> > +};
> > +
> > +/* Page 1, Register 0x07 */
> > +enum {
> > +	BPCKSEL		= BIT(7),
> > +	DRI_CMFB_EN	= BIT(6),
> > +	CEC_PUEN	= BIT(5),
> > +	CEC_T		= BIT(3),
> > +	CKINV		= BIT(2),
> > +	CK_TVINV	= BIT(1),
> > +	DRI_CKS2	= BIT(0),
> > +};
> > +
> > +/* Page 1, Register 0x08 */
> > +enum {
> > +	DACG		= BIT(6),
> > +	DACKTST		= BIT(5),
> > +	DEDGEB		= BIT(4),
> > +	SYO		= BIT(3),
> > +	DRI_IT_LVDS	= GENMASK(2, 1),
> > +	DISPON		= BIT(0),
> > +};
> > +
> > +/* Page 1, Register 0x0c */
> > +enum {
> > +	DRI_PLL_CP	= GENMASK(7, 6),
> > +	DRI_PLL_DIVSEL	= BIT(5),
> > +	DRI_PLL_N1_1	= BIT(4),
> > +	DRI_PLL_N1_0	= BIT(3),
> > +	DRI_PLL_N3_1	= BIT(2),
> > +	DRI_PLL_N3_0	= BIT(1),
> > +	DRI_PLL_CKTSTEN = BIT(0),
> > +};
> > +
> > +/* Page 1, Register 0x6b */
> > +enum {
> > +	VCO3CS		= GENMASK(7, 6),
> > +	ICPGBK2_0	= GENMASK(5, 3),
> > +	DRI_VCO357SC	= BIT(2),
> > +	PDPLL2		= BIT(1),
> > +	DRI_PD_SER	= BIT(0),
> > +};
> > +
> > +/* Page 1, Register 0x6c */
> > +enum {
> > +	PLL2N11		= GENMASK(7, 4),
> > +	PLL2N5_4	= BIT(3),
> > +	PLL2N5_TOP	= BIT(2),
> > +	DRI_PLL_PD	= BIT(1),
> > +	PD_I2CM		= BIT(0),
> > +};
> > +
> > +/* Page 3, Register 0x28 */
> > +enum {
> > +	DIFF_EN		= GENMASK(7, 6),
> > +	CORREC_EN	= GENMASK(5, 4),
> > +	VGACLK_BP	= BIT(3),
> > +	HM_LV_SEL	= BIT(2),
> > +	HD_VGA_SEL	= BIT(1),
> > +};
> > +
> > +/* Page 3, Register 0x2a */
> > +enum {
> > +	LVDSCLK_BP	= BIT(7),
> > +	HDTVCLK_BP	= BIT(6),
> > +	HDMICLK_BP	= BIT(5),
> > +	HDTV_BP		= BIT(4),
> > +	HDMI_BP		= BIT(3),
> > +	THRWL		= GENMASK(2, 0),
> > +};
> > +
> > +/* Page 4, Register 0x52 */
> > +enum {
> > +	PGM_ARSTB	= BIT(7),
> > +	MCU_ARSTB	= BIT(6),
> > +	MCU_RETB	= BIT(2),
> > +	RESETIB		= BIT(1),
> > +	RESETDB		= BIT(0),
> > +};
> > +
> > +struct ch7033_priv {
> > +	struct i2c_client *client;
> > +	struct i2c_adapter *ddc;
> > +	struct gpio_desc *hpd;
> > +	struct drm_encoder encoder;
> > +	struct drm_bridge bridge;
> > +	struct drm_connector connector;
> > +};
> > +
> > +#define conn_to_ch7033_priv(x) \
> > +	container_of(x, struct ch7033_priv, connector)
> > +#define bridge_to_ch7033_priv(x) \
> > +	container_of(x, struct ch7033_priv, bridge)
> > +
> > +
> > +static int32_t ch7033_update_reg(struct i2c_client *client,
> > +				 u8 command, u8 value, u8 mask)
> > +{
> > +	int ret;
> > +
> > +	ret = i2c_smbus_read_byte_data(client, command);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	ret &= ~mask;
> > +	ret |= value;
> > +	return i2c_smbus_write_byte_data(client, command, ret);
> 
> How about using regmap ?
> 
> > +}
> > +
> > +static enum drm_connector_status ch7033_connector_detect(
> > +	struct drm_connector *connector, bool force)
> > +{
> > +	struct ch7033_priv *priv = conn_to_ch7033_priv(connector);
> > +
> > +	if (priv->hpd) {
> > +		if (gpiod_get_value_cansleep(priv->hpd))
> > +			return connector_status_connected;
> > +	} else if (priv->ddc) {
> > +		if (drm_probe_ddc(priv->ddc))
> > +			return connector_status_connected;
> > +	}
> > +
> > +	return connector_status_unknown;
> > +}
> > +
> > +static void ch7033_connector_destroy(struct drm_connector *connector)
> > +{
> > +	drm_connector_cleanup(connector);
> > +}
> > +
> > +static const struct drm_connector_funcs ch7033_connector_funcs = {
> > +	.reset = drm_atomic_helper_connector_reset,
> > +	.fill_modes = drm_helper_probe_single_connector_modes,
> > +	.detect = ch7033_connector_detect,
> > +	.destroy = ch7033_connector_destroy,
> > +	.atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> > +	.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> > +};
> > +
> > +static int ch7033_connector_get_modes(struct drm_connector *connector)
> > +{
> > +	struct ch7033_priv *priv = conn_to_ch7033_priv(connector);
> > +	struct edid *edid;
> > +	int ret;
> > +
> > +	edid = drm_get_edid(connector, priv->ddc);
> > +	drm_connector_update_edid_property(connector, edid);
> > +	if (edid) {
> > +		ret = drm_add_edid_modes(connector, edid);
> > +		kfree(edid);
> > +	} else {
> > +		ret = drm_add_modes_noedid(connector, 1920, 1080);
> > +		drm_set_preferred_mode(connector, 1024, 768);
> > +	}
> > +	return ret;
> > +}
> > +
> > +static struct drm_encoder *ch7033_connector_best_encoder(
> > +			struct drm_connector *connector)
> > +{
> > +	struct ch7033_priv *priv = conn_to_ch7033_priv(connector);
> > +
> > +	return priv->bridge.encoder;
> > +}
> > +
> > +static const struct drm_connector_helper_funcs ch7033_connector_helper_funcs = {
> > +	.get_modes = ch7033_connector_get_modes,
> > +	.best_encoder = ch7033_connector_best_encoder,
> > +};
> > +
> > +static irqreturn_t ch7033_hpd_irq(int irq, void *data)
> > +{
> > +	struct ch7033_priv *priv = data;
> > +
> > +	if (priv->connector.dev)
> > +		drm_helper_hpd_irq_event(priv->connector.dev);
> > +
> > +	return IRQ_HANDLED;
> > +}
> > +
> > +static int ch7033_bridge_attach(struct drm_bridge *bridge)
> > +{
> > +	struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge);
> > +	struct drm_connector *connector = &priv->connector;
> > +	int ret;
> > +
> > +	if (priv->hpd) {
> > +		connector->polled = DRM_CONNECTOR_POLL_HPD;
> > +	} else if (priv->ddc) {
> > +		connector->polled = DRM_CONNECTOR_POLL_CONNECT |
> > +				    DRM_CONNECTOR_POLL_DISCONNECT;
> > +	}
> > +
> > +	drm_connector_helper_add(connector,
> > +				 &ch7033_connector_helper_funcs);
> > +	ret = drm_connector_init_with_ddc(bridge->dev, connector,
> > +					  &ch7033_connector_funcs,
> > +					  DRM_MODE_CONNECTOR_DVII,
> > +					  priv->ddc);
> > +	if (ret) {
> > +		DRM_ERROR("Failed to initialize connector\n");
> > +		return ret;
> > +	}
> > +
> > +	drm_connector_attach_encoder(&priv->connector,
> > +				     priv->bridge.encoder);
> > +
> > +	return 0;
> > +}
> > +
> > +static void ch7033_bridge_detach(struct drm_bridge *bridge)
> > +{
> > +	struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge);
> > +
> > +	drm_connector_cleanup(&priv->connector);
> > +}
> > +
> > +static enum drm_mode_status ch7033_bridge_mode_valid(struct drm_bridge *bridge,
> > +				     const struct drm_display_mode *mode)
> > +{
> > +	if (mode->clock > 165000)
> > +		return MODE_CLOCK_HIGH;
> > +	if (mode->hdisplay >= 1920)
> > +		return MODE_BAD_HVALUE;
> > +	if (mode->vdisplay >= 1080)
> > +		return MODE_BAD_VVALUE;
> > +	return MODE_OK;
> > +}
> > +
> > +static void ch7033_bridge_disable(struct drm_bridge *bridge)
> > +{
> > +	struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge);
> > +
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x04);
> > +	ch7033_update_reg(priv->client, 0x52, 0x00, RESETDB);
> > +}
> > +
> > +static void ch7033_bridge_enable(struct drm_bridge *bridge)
> > +{
> > +	struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge);
> > +
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x04);
> > +	ch7033_update_reg(priv->client, 0x52, RESETDB, RESETDB);
> > +}
> > +
> > +static void ch7033_bridge_mode_set(struct drm_bridge *bridge,
> > +				   const struct drm_display_mode *mode,
> > +				   const struct drm_display_mode *adjusted_mode)
> > +{
> > +	struct ch7033_priv *priv = bridge_to_ch7033_priv(bridge);
> > +	int hbporch = mode->hsync_start - mode->hdisplay;
> > +	int hsynclen = mode->hsync_end - mode->hsync_start;
> > +	int vbporch = mode->vsync_start - mode->vdisplay;
> > +	int vsynclen = mode->vsync_end - mode->vsync_start;
> > +
> > +	/*
> > +	 * Page 4
> > +	 */
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x04);
> > +
> > +	/* Turn everything off to set all the registers to their defaults. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x52, 0x00);
> > +	/* Bring I/O block up. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x52, RESETIB);
> > +
> > +	/*
> > +	 * Page 0
> > +	 */
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x00);
> > +
> > +	/* Bring up parts we need from the power down. */
> > +	ch7033_update_reg(priv->client, 0x07, 0, DRI_PD | IO_PD);
> > +	ch7033_update_reg(priv->client, 0x08, 0, DRI_PDDRI | PDDAC | PANEN);
> > +	ch7033_update_reg(priv->client, 0x09, 0, HDMI_PD | VGA_PD |
> > +						 DPD | GCKOFF);
> > +	ch7033_update_reg(priv->client, 0x0a, 0, HD_DVIB);
> > +
> > +	/* Horizontal input timing. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x0b, (mode->htotal >> 8) << 3 |
> > +						      (mode->hdisplay >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x0c, mode->hdisplay);
> > +	i2c_smbus_write_byte_data(priv->client, 0x0d, mode->htotal);
> > +	i2c_smbus_write_byte_data(priv->client, 0x0e, (hsynclen >> 8) << 3 |
> > +						      (hbporch >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x0f, hbporch);
> > +	i2c_smbus_write_byte_data(priv->client, 0x10, hsynclen);
> > +
> > +	/* Vertical input timing. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x11, (mode->vtotal >> 8) << 3 |
> > +						      (mode->vdisplay >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x12, mode->vdisplay);
> > +	i2c_smbus_write_byte_data(priv->client, 0x13, mode->vtotal);
> > +	i2c_smbus_write_byte_data(priv->client, 0x14, ((vsynclen >> 8) << 3) |
> > +						      (vbporch >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x15, vbporch);
> > +	i2c_smbus_write_byte_data(priv->client, 0x16, vsynclen);
> > +
> > +	/* Input color swap. */
> > +	ch7033_update_reg(priv->client, 0x18, BYTE_SWAP_BGR, SWAP);
> > +
> > +	/* Input clock and sync polarity. */
> > +	ch7033_update_reg(priv->client, 0x19, mode->clock >> 16, 0x1);
> > +	ch7033_update_reg(priv->client, 0x19,
> > +			  (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_I : 0 |
> > +			  (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_I : 0 |
> > +			  mode->clock >> 16,
> > +			  HPO_I | VPO_I | GCLKFREQ);
> > +	i2c_smbus_write_byte_data(priv->client, 0x1a, mode->clock >> 8);
> > +	i2c_smbus_write_byte_data(priv->client, 0x1b, mode->clock);
> > +
> > +	/* Horizontal output timing. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x1f, (mode->htotal >> 8) << 3 |
> > +						      (mode->hdisplay >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x20, mode->hdisplay);
> > +	i2c_smbus_write_byte_data(priv->client, 0x21, mode->htotal);
> > +
> > +	/* Vertical output timing. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x25, (mode->vtotal >> 8) << 3 |
> > +						      (mode->vdisplay >> 8));
> > +	i2c_smbus_write_byte_data(priv->client, 0x26, mode->vdisplay);
> > +	i2c_smbus_write_byte_data(priv->client, 0x27, mode->vtotal);
> > +
> > +	/* VGA channel bypass */
> > +	ch7033_update_reg(priv->client, 0x2b, 9, VFMT);
> > +
> > +	/* Output sync polarity. */
> > +	ch7033_update_reg(priv->client, 0x2e,
> > +			  (mode->flags & DRM_MODE_FLAG_PHSYNC) ? HPO_O : 0 |
> > +			  (mode->flags & DRM_MODE_FLAG_PVSYNC) ? VPO_O : 0,
> > +			  HPO_O | VPO_O);
> > +
> > +	/* HDMI horizontal output timing. */
> > +	ch7033_update_reg(priv->client, 0x54, (hsynclen >> 8) << 3 |
> > +					      (hbporch >> 8),
> > +					      HWO_HDMI_HI | HOO_HDMI_HI);
> > +	i2c_smbus_write_byte_data(priv->client, 0x55, hbporch);
> > +	i2c_smbus_write_byte_data(priv->client, 0x56, hsynclen);
> > +
> > +	/* HDMI vertical output timing. */
> > +	ch7033_update_reg(priv->client, 0x57, (vsynclen >> 8) << 3 |
> > +					      (vbporch >> 8),
> > +					      VWO_HDMI_HI | VOO_HDMI_HI);
> > +	i2c_smbus_write_byte_data(priv->client, 0x58, vbporch);
> > +	i2c_smbus_write_byte_data(priv->client, 0x59, vsynclen);
> > +
> > +	/* Pick HDMI, not LVDS. */
> > +	ch7033_update_reg(priv->client, 0x7e, HDMI_LVDS_SEL, HDMI_LVDS_SEL);
> > +
> > +	/*
> > +	 * Page 1
> > +	 */
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x01);
> > +
> > +	/* No idea what these do, but VGA is wobbly and blinky without them. */
> > +	ch7033_update_reg(priv->client, 0x07, CKINV, CKINV);
> > +	ch7033_update_reg(priv->client, 0x08, DISPON, DISPON);
> > +
> > +	/* DRI PLL */
> > +	ch7033_update_reg(priv->client, 0x0c, DRI_PLL_DIVSEL, DRI_PLL_DIVSEL);
> > +	if (mode->clock <= 40000) {
> > +		ch7033_update_reg(priv->client, 0x0c, 0,
> > +						      DRI_PLL_N1_1 |
> > +						      DRI_PLL_N1_0 |
> > +						      DRI_PLL_N3_1 |
> > +						      DRI_PLL_N3_0);
> > +	} else if (mode->clock < 80000) {
> > +		ch7033_update_reg(priv->client, 0x0c, DRI_PLL_N3_0 |
> > +						      DRI_PLL_N1_0,
> > +						      DRI_PLL_N1_1 |
> > +						      DRI_PLL_N1_0 |
> > +						      DRI_PLL_N3_1 |
> > +						      DRI_PLL_N3_0);
> > +	} else {
> > +		ch7033_update_reg(priv->client, 0x0c, DRI_PLL_N3_1 |
> > +						      DRI_PLL_N1_1,
> > +						      DRI_PLL_N1_1 |
> > +						      DRI_PLL_N1_0 |
> > +						      DRI_PLL_N3_1 |
> > +						      DRI_PLL_N3_0);
> > +	}
> > +
> > +	/* This seems to be color calibration for VGA. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x64, 0x29); /* LSB Blue */
> > +	i2c_smbus_write_byte_data(priv->client, 0x65, 0x29); /* LSB Green */
> > +	i2c_smbus_write_byte_data(priv->client, 0x66, 0x29); /* LSB Red */
> > +	i2c_smbus_write_byte_data(priv->client, 0x67, 0x00); /* MSB Blue */
> > +	i2c_smbus_write_byte_data(priv->client, 0x68, 0x00); /* MSB Green */
> > +	i2c_smbus_write_byte_data(priv->client, 0x69, 0x00); /* MSB Red */
> > +
> > +	ch7033_update_reg(priv->client, 0x6b, 0x00, DRI_PD_SER);
> > +	ch7033_update_reg(priv->client, 0x6c, 0x00, DRI_PLL_PD);
> > +
> > +	/*
> > +	 * Page 3
> > +	 */
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x03);
> > +
> > +	/* More bypasses and apparently another HDMI/LVDS selector. */
> > +	ch7033_update_reg(priv->client, 0x28, VGACLK_BP | HM_LV_SEL,
> > +					      VGACLK_BP | HM_LV_SEL);
> > +	ch7033_update_reg(priv->client, 0x2a, HDMICLK_BP | HDMI_BP,
> > +					      HDMICLK_BP | HDMI_BP);
> > +
> > +	/*
> > +	 * Page 4
> > +	 */
> > +	i2c_smbus_write_byte_data(priv->client, 0x03, 0x04);
> > +
> > +	/* Output clock. */
> > +	i2c_smbus_write_byte_data(priv->client, 0x10, mode->clock >> 16);
> > +	i2c_smbus_write_byte_data(priv->client, 0x11, mode->clock >> 8);
> > +	i2c_smbus_write_byte_data(priv->client, 0x12, mode->clock);
> > +}
> > +
> > +static const struct drm_bridge_funcs ch7033_bridge_funcs = {
> > +	.attach = ch7033_bridge_attach,
> > +	.detach = ch7033_bridge_detach,
> > +	.mode_valid = ch7033_bridge_mode_valid,
> > +	.disable = ch7033_bridge_disable,
> > +	.enable = ch7033_bridge_enable,
> > +	.mode_set = ch7033_bridge_mode_set,
> > +};
> > +
> > +static void ch7033_encoder_destroy(struct drm_encoder *encoder)
> > +{
> > +	drm_encoder_cleanup(encoder);
> > +}
> > +
> > +static const struct drm_encoder_funcs ch7033_encoder_funcs = {
> > +	.destroy = ch7033_encoder_destroy,
> > +};
> > +
> > +static int ch7033_bind(struct device *dev, struct device *master,
> > +		       void *data)
> > +{
> > +	struct drm_device *drm = data;
> > +	struct ch7033_priv *priv = dev_get_drvdata(dev);
> > +	uint32_t crtcs;
> > +	int ret;
> > +
> > +	crtcs = drm_of_find_possible_crtcs(drm, dev->of_node);
> > +	priv->encoder.possible_crtcs = crtcs;
> > +
> > +	ret = drm_encoder_init(drm, &priv->encoder, &ch7033_encoder_funcs,
> > +			       DRM_MODE_ENCODER_TMDS, NULL);
> 
> Bridge drivers must not create encoders, this is the responsibility of
> the display controller driver.
> 
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL);
> > +	if (ret)
> > +		drm_encoder_cleanup(&priv->encoder);
> > +
> > +	return ret;
> > +}
> > +
> > +static void ch7033_unbind(struct device *dev, struct device *master,
> > +			  void *data)
> > +{
> > +	struct ch7033_priv *priv = dev_get_drvdata(dev);
> > +
> > +	drm_encoder_cleanup(&priv->encoder);
> > +}
> > +
> > +static const struct component_ops ch7033_ops = {
> > +	.bind = ch7033_bind,
> > +	.unbind = ch7033_unbind,
> > +};
> > +
> > +static int ch7033_probe(struct i2c_client *client,
> > +			const struct i2c_device_id *id)
> > +{
> > +	struct device_node *ddc_node, *conn_node;
> > +	struct device *dev = &client->dev;
> > +	struct ch7033_priv *priv;
> > +	struct i2c_adapter *ddc;
> > +	int ret;
> > +
> > +	conn_node = of_graph_get_remote_node(dev->of_node, 1, -1);
> > +	if (!conn_node) {
> > +		dev_err(&client->dev, "unable to get the connector node\n");
> > +		return -EINVAL;
> > +	}
> > +
> > +	ddc_node = of_parse_phandle(conn_node, "ddc-i2c-bus", 0);
> > +	if (ddc_node) {
> > +		ddc = of_get_i2c_adapter_by_node(ddc_node);
> > +		if (!ddc) {
> > +			ret = -EPROBE_DEFER;
> > +			goto out;
> > +		}
> > +	} else {
> > +		dev_info(&client->dev, "no DDC bus for connector\n");
> > +		ddc = NULL;
> > +	}
> > +
> > +	ret = i2c_smbus_read_byte_data(client, 0x00);
> 
> Any idea what this is for ?
> 
> > +	if ((i2c_smbus_read_byte_data(client, 0x00) & 0xf7) != 0x56) {
> > +		dev_err(&client->dev, "the device is not a ch7033\n");
> > +		ret = -ENODEV;
> > +		goto out;
> > +	}
> > +
> > +	i2c_smbus_write_byte_data(client, 0x03, 0x04);
> > +	ret = i2c_smbus_read_byte_data(client, 0x51) & 0x0f;
> > +	if (ret != 3) {
> > +		dev_err(&client->dev, "unknown revision %d\n", ret);
> > +		ret = -ENODEV;
> > +		goto out;
> > +	}
> > +
> > +	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> > +	if (!priv) {
> > +		ret = -ENODEV;
> > +		goto out;
> > +	}
> > +
> > +	dev_set_drvdata(dev, priv);
> > +
> > +	INIT_LIST_HEAD(&priv->bridge.list);
> > +
> > +	priv->client = client;
> > +	priv->ddc = ddc;
> > +
> > +	priv->hpd = devm_gpiod_get_from_of_node(dev, conn_node, "hpd-gpios",
> > +						0, GPIOD_IN, "HPD");
> > +	if (IS_ERR(priv->hpd)) {
> > +		if (PTR_ERR(priv->hpd) == -ENOENT) {
> > +			dev_info(&client->dev, "no HPD pin\n");
> > +			priv->hpd = NULL;
> > +		} else {
> > +			ret = PTR_ERR(priv->hpd);
> > +			goto out;
> > +		}
> > +	}
> > +
> > +	if (priv->hpd) {
> > +		ret = devm_request_threaded_irq(&client->dev,
> > +						gpiod_to_irq(priv->hpd),
> > +						NULL, ch7033_hpd_irq,
> > +						IRQF_TRIGGER_RISING |
> > +						IRQF_TRIGGER_FALLING |
> > +						IRQF_ONESHOT,
> > +						"HPD", priv);
> > +		if (ret) {
> > +			dev_err(&client->dev, "failed to request irq\n");
> > +			goto out;
> > +		}
> > +	}
> 
> Instead of manually handling the connector DT node, how about using
> https://patchwork.freedesktop.org/patch/346013/ ? We're about to merge
> it.
> 
> > +
> > +	priv->bridge.funcs = &ch7033_bridge_funcs;
> > +	priv->bridge.of_node = dev->of_node;
> > +
> > +	drm_bridge_add(&priv->bridge);
> > +
> > +	ret = component_add(dev, &ch7033_ops);
> > +	if (ret) {
> > +		drm_bridge_remove(&priv->bridge);
> > +		goto out;
> > +	}
> > +
> > +	dev_info(dev, "Chrontel CH7033 Video Encoder\n");
> > +out:
> > +	of_node_put(conn_node);
> > +	return ret;
> > +}
> > +
> > +static int ch7033_remove(struct i2c_client *client)
> > +{
> > +	struct device *dev = &client->dev;
> > +	struct ch7033_priv *priv = dev_get_drvdata(dev);
> > +
> > +	component_del(dev, &ch7033_ops);
> > +	drm_bridge_remove(&priv->bridge);
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct of_device_id ch7033_dt_ids[] = {
> > +	{ .compatible = "chrontel,ch7033", },
> > +	{ }
> > +};
> > +MODULE_DEVICE_TABLE(of, ch7033_dt_ids);
> > +
> > +static const struct i2c_device_id ch7033_ids[] = {
> > +	{ "ch7033", 0 },
> > +	{ }
> > +};
> > +MODULE_DEVICE_TABLE(i2c, ch7033_ids);
> > +
> > +static struct i2c_driver ch7033_driver = {
> > +	.probe = ch7033_probe,
> > +	.remove = ch7033_remove,
> > +	.driver = {
> > +		.name = "ch7033",
> > +		.of_match_table = of_match_ptr(ch7033_dt_ids),
> > +	},
> > +	.id_table = ch7033_ids,
> > +};
> > +
> > +module_i2c_driver(ch7033_driver);
> > +
> > +MODULE_AUTHOR("Lubomir Rintel <lkundrak@v3.sk>");
> > +MODULE_DESCRIPTION("Chrontel CH7033 Video Encoder Driver");
> > +MODULE_LICENSE("GPL v2");


      reply	other threads:[~2020-01-10 23:01 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-20  7:49 Add support for Chrontel CH7033 VGA/DVI Encoder Lubomir Rintel
2019-12-20  7:49 ` [PATCH 1/3] dt-bindings: Add vendor prefix for Chrontel, Inc Lubomir Rintel
2020-01-08 14:19   ` Rob Herring
2019-12-20  7:49 ` [PATCH 2/3] dt-bindings: display: Add Chrontel CH7033 Video Encoder binding Lubomir Rintel
2020-01-08 14:21   ` Rob Herring
2019-12-20  7:49 ` [PATCH 3/3] drm/bridge: chrontel-ch7033: Add a new driver Lubomir Rintel
2020-01-08 15:20   ` Laurent Pinchart
2020-01-10 23:00     ` Lubomir Rintel [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=b3a08fc36f19347e50b9fe0943287503d7f39cf7.camel@v3.sk \
    --to=lkundrak@v3.sk \
    --cc=a.hajda@samsung.com \
    --cc=airlied@linux.ie \
    --cc=daniel@ffwll.ch \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=jernej.skrabec@siol.net \
    --cc=jonas@kwiboo.se \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=narmstrong@baylibre.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).