Re: [PATCH 3/3] arm64: dts: qcom: msm8916-acer-a1-724: Add accelerometer/magnetometer

From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: "Lin, Meng-Bo" <linmengbo0689@protonmail.com>,
	linux-kernel@vger.kernel.org
Cc: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <andersson@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Stephan Gerhold <stephan@gerhold.net>,
	Nikita Travkin <nikita@trvn.ru>,
	devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org,
	~postmarketos/upstreaming@lists.sr.ht
Subject: Re: [PATCH 3/3] arm64: dts: qcom: msm8916-acer-a1-724: Add accelerometer/magnetometer
Date: Mon, 21 Nov 2022 12:24:28 +0100	[thread overview]
Message-ID: <b6c03e36-6f4b-bf6d-b209-a2afbb7f65ad@linaro.org> (raw)
In-Reply-To: <20221119194727.92107-1-linmengbo0689@protonmail.com>


On 19.11.2022 20:48, Lin, Meng-Bo wrote:
> Iconia Talk S uses a Bosch BMC150 accelerometer/magnetometer combo.
> The chip provides two separate I2C devices for the accelerometer
> and magnetometer that are already supported by the bmc150-accel
> and bmc150-magn driver.
> 
> Signed-off-by: Lin, Meng-Bo <linmengbo0689@protonmail.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  .../boot/dts/qcom/msm8916-acer-a1-724.dts     | 38 +++++++++++++++++++
>  1 file changed, 38 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> index acd909551a75..3461a39ee866 100644
> --- a/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> +++ b/arch/arm64/boot/dts/qcom/msm8916-acer-a1-724.dts
> @@ -6,6 +6,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  /*
>   * NOTE: The original firmware from Acer can only boot 32-bit kernels.
> @@ -51,6 +52,35 @@ usb_id: usb-id {
>  	};
>  };
>  
> +&blsp_i2c2 {
> +	status = "okay";
> +
> +	accelerometer@10 {
> +		compatible = "bosch,bmc150_accel";
> +		reg = <0x10>;
> +		interrupt-parent = <&msmgpio>;
> +		interrupts = <115 IRQ_TYPE_EDGE_RISING>;
> +
> +		vdd-supply = <&pm8916_l17>;
> +		vddio-supply = <&pm8916_l6>;
> +
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&accel_int_default>;
> +
> +		mount-matrix = "0", "-1", "0",
> +			       "-1", "0", "0",
> +			       "0", "0", "1";
> +	};
> +
> +	magnetometer@12 {
> +		compatible = "bosch,bmc150_magn";
> +		reg = <0x12>;
> +
> +		vdd-supply = <&pm8916_l17>;
> +		vddio-supply = <&pm8916_l6>;
> +	};
> +};
> +
>  &blsp1_uart2 {
>  	status = "okay";
>  };
> @@ -199,6 +229,14 @@ l18 {
>  };
>  
>  &msmgpio {
> +	accel_int_default: accel-int-default-state {
> +		pins = "gpio115";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
>  	gpio_keys_default: gpio-keys-default-state {
>  		pins = "gpio107";
>  		function = "gpio";